In this Field Test Shooting Video I test out the KJWorks CZ P-09 GBB Airsoft Pistol in the Replica Airguns Indoor Sea Can Shooting Range to find out what the velocity and accuracy is using .20 gram Airsoft BB’s. If you’re more interested in details, specifications and close up video of the KJWorks CZ P-09 GBB Airsoft Pistol then make sure to watch my Table Top Video for that information.
Starting with the velocity test I averaged out 6 rounds using my chronograph to find out the fps velocity for the KJWorks CZ P-09 GBB Airsoft Pistol and I was able to get 279.5 fps, the slowest of the 6 shots was 279 with the fastest being 281 so actually fairly closer to each other. I do mention at the end of the video that it felt like the velocity was not consistent because the blowback action to me felt like it was heavier on some shots than others? I felt like this might effect accuracy in terms of elevations if the velocity was not consistent but it ended up not being a factor as far as I could tell.
For my accuracy test I loaded 10 rounds in the KJWorks CZ P-09 GBB Airsoft Pistol and proceeded to place them to the best of my ability into my paper target setup 30 feet down range using a rested and seated shooting position (Sand bag up front, seated on a stool in the back). Even though the grouping spread out to about 4 inches, all but one round stayed within about 2 inches and side to side the spread was closer to about 1.5 inches for all shots. In terms of placement on the target they where all fairly well centered out of the box.
The fps for the KJWorks CZ P-09 GBB Airsoft Pistol is a bit low using the preinstalled short internal barrel that does not allow for the added threaded barrel extension but you could install the short internal threaded barrel and add the external barrel extension to increase the fps to more in the range of 360+. That said you would have a fairly long brass inner barrel protruding from your gun with no way I can see to install a mock suppressor to hide it so it would not look so good this way and there is also the possibility of damaging the thin exposed external barrel. Overall the KJWorks CZ P-09 GBB Airsoft Pistol performed well but I feel needs a little bit of break in time to smooth out the blowback consistency but even as is it shot consistent fps and was able to get most rounds well placed on the center of the target.
Type: Gas Blowback Airsoft Pistol. Manufacturer: KJWorks Model: CZ P-09 Materials: Metal & Polymer. Weight: 2.3 pounds (1050 grams). Length: 9 inches (229mm) total. Barrel: 4.4 inches (120mm),Metal non-rifled smooth bore. (Comes with barrel extension) Propulsion: Green gas or propane. Action: Blowback, single and double action. Ammunition Type: 6mm plastic Airsoft BB's. Ammunition Capacity: 25rounds. FPS: 376 fps.
Trigger Pull: The trigger pull on the KJWorks CZ P-09 GBB Airsoft Pistol is good in both single and double action shooting modes. Most of the time you will be shooting in single action as the blowback action will do all the work cycling the slide and retracting the hammer allowing for light quick single action follow up shots. If you do decide to drop the hammer in-between shooting you can then pull the double action trigger which is much longer and a bit heavier but this will draw the hammer back and release the trigger as expected with single action shots to follow.
Accuracy: So far I have not made my Field Test Shooting Video for the KJWorks CZ P-09 GBB Airsoft Pistol but do expect it to behave much like the ASG distributed version of this same gun which by the way is also made by KJWorks. The only real difference to consider will be the gas used in both of these Airsoft guns as the ASG distributed version uses CO2 while the KJWorks version reviewed in this video uses Green Gas or Propane which will reduce the velocity a little bit. We will find out next week when I make my Field Test Shooting Video for the KJWorks CZ P-09 GBB Airsoft Pistol.
Build Quality: KJWorks is know for making high quality products and the KJWorks CZ P-09 GBB Airsoft Pistol is no different. Fit and finish is excellent and the quality of material is also very good with similar materials used as you would expect them compared to the real steel version with the exception of the metals not having to be as high grade because of way less force and pressure on the Airsoft version.
Realism: The KJWorks CZ P-09 GBB Airsoft Pistol is a one to one Replica of the real steel CZ P-09 firearm and on first inspection would be hard to tell apart. You are going to find CZ licensing throughout this Airsoft Pistol in all the right places and all the controls work just like the powder burning CZ P-09. The full blowback operation, reassessed barrel and ability to field strip it also aid in making the shooting experience super realistic.
Pros:
Build quality feels really goods, lots of weight to this Airsoft Pistol.
Full length blowback action.
Accurate licensed CZ P-09 Replica.
Trigger pull is nice in both single and double action.
Picatinny rail for adding accessories like a tac light or laser.
Double stack full size drop out Metal Magazine holds the Green Gas and 25 Airsoft BB’s
No orange tip which is always nice.
Easy to see white dot front and back sights.
Green Gas which when using propane is fairly cheap to shoot.
Easily Field Strippable.
Adjustable Hop-up.
Cons:
Sights don’t seem to be adjustable.
Controls are not fully ambidextrous.
Green Gas version has less velocity than CO2 version.
Comments:
The KJWorks CZ P-09 GBB Airsoft Pistol is really almost exactly like the ASG Distributed version since both are made by KJWorks at the end of the day. There are some slight differences between them like CO2 versus Green Gas and some other very minimal cosmetic changes. I would say go with which ever version is in stock and perhaps is less expensive at the time. You really can’t go wrong as this is a great choice to make for an Airsoft Side arm to use on the Airsoft field or for plinking in your yard or indoor range.
My Table Top Review Video of the KJWorks CZ P-09 GBB Airsoft Pistol:
In this Field Test Shooting Video I perform two main test in the Replica Airguns Sea Can using the KJWorks KP-16 GBB Airsoft Pistol. First a chronograph test to see what the real world velocity is and then I perform an accuracy test to see how accurate the KJWorks KP-16 GBB Airsoft Pistol is at 30 feet from the target. If you’re interested more in specifications and details along with close up video of the KJWorks KP-16 GBB Airsoft Pistol then check out my Table Top Video Review for it where I show you around and do a field strip on camera.
Starting off with my chronograph velocity test. I decided to find out what the differences would be using the included internal short barrel and the extended external barrel since the KJWorks KP-16 GBB Airsoft Pistol does come with both in the box to allow for higher fps and easier import into Canada. The KJWorks KP-16 GBB Airsoft Pistol is rated for 360+ fps using the extended longer barrel so I used that one first to establish a baseline and was able to achieve a 394 fps 4 shot average. Switching up to the shorter internal barrel without the extension, the velocity was reduces as expected and I got an average 3 shoot velocity of 301 fps. So I can safely say that the barrel extension added an additional 90+ fps to the velocity in this case!
Next I placed a brand new paper target 30 feet down range and shot ten 20 gram Airsoft BB’s into it using a seated shooting position with my hands resting on a sand bag up front, this allows for a fairly stable platform to shoot from but is not without some human error to factor in. I also decided to use the barrel extension for this test as the threading on the end of the internal barrel can disrupt airflow causing air turbulence a bit and effect accuracy. I was able to get around a 2 inch grouping with my 10 rounds. The KP-16 GBB Airsoft Pistol shot a bit low and to the left out fo the box, adjusting the hop-up should correct the elevation but in terms of windage there is not sight adjustment other than perhaps playing around with the front removable sight and trying to movie it a bit to the left so as to make it shoot more to the right.
My take on the KJWorks KP-16 GBB Airsoft Pistol is it is a solid Airsoft Shooter with great modern 1911 tactical looks. The white dot sights make it a lot easier for my older eyes to line up on the target which makes this more practical for me. I also like the higher capacity magazine which again makes this a decent side arm for Airsoft wars. If you like the look of the 1911 but want it in a bit more of a modern configuration then the KJWorks KP-16 GBB Airsoft Pistol may just be the way to go!
In this Update Preview Unboxing Video I take a look at 4 newer products that just came across my table and are in our Replica Airguns Online Stores. One is a CO2 Blowback BB Pistol, one is a CO2 .43 Caliber Paintball Pistol and two are GBB Airsoft Pistols, so a rather nice selection for us to take a look at here! I will be following up this Update Preview Unboxing Video with proper Table Top and Field Test Shooting Video to find out all the details and how well they perform.
Type: GBB Airsoft Pistol. Manufacturer: KJWorks Model:KP-16 Materials: Mostly all metal build. Weight: 2.16 pounds (980 grams). Barrel: 4.5 inches, non-rifled. Length: 9.75 inches. Propulsion: Green Gas / Propane (Can also accept a CO2 Magazine) Action: Semi Auto, single action only trigger. Ammunition Type: 6mm Plastic Airsoft BB's. Ammunition Capacity: 26 round full size dropout metal magazine. FPS: 366+ with extended barrel.
Trigger Pull: The trigger pull on the KJWorks KP-16 GBB Airsoft Pistol is exactly what your would expect from a 1911 pistol which is always a good thing as 1911’s are generally short and light which makes fast action shooting super fun and easy! There is virtually no take-up in the trigger, and then a predictable nice and light release. Trigger reset is almost non existent like most 1911’s.
Accuracy: I have not yet made my Field Test Shooting Video for the KJWorks KP-16 GBB Airsoft Pistol but plan to next week so stay posted for that video. I will be testing out both the included extended barrel and internal short barrels to see what the velocity difference will be and then when it comes to accuracy I will test out the KJWorks KP-16 GBB Airsoft Pistol using the extended barrel to exclude the threading on the short barrel interfering with airflow and accuracy.
Build Quality: The KJWorks KP-16 GBB Airsoft Pistol is a really great looking pistol with its tan with black/dark accent finish. You will find it has that KJWorks solid build quality, it is virtually all metal even including the chunky grips being metal. Fit and finish is excellent, I’m not sure if there is a better made Airsoft 1911 out there?
Realism: As is with most Full Blowback Airsoft Pistols they are built to look and act the part of their real steel counterparts and the KJWorks KP-16 GBB Airsoft Pistol checks off all the boxes here! All mechanical parts work just like the real steel version and you can easily field strip the KJWorks KP-16 GBB Airsoft Pistol to swap out the internal barrel and adjust the hop-up. I like the fact that If you are not a fan of the compensator extension then you will be happy to know that KJWorks also includes a standard barrel bushing you can replace it with to shorten up the gun and make it look more traditional to a 1911.
Pros:
Full metal gun with good weight to it.
Heavy Full blowback operation.
Excellent fit and finish as always with KJWorks pistols.
High capacity full size drop out magazine that holds 26 rounds.
Versatile magazine options, also works with CO2 magazines.
Easy to see white dot sights front and back.
All working components like the real steel 1911.
Vented extended barrel compensator looks great but can be removed easily.
Comes with extended barrel for higher velocity and easier import into Canada.
Field strip-able.
Cons:
Sights are not adjustable.
Real steel grips will not fit without some modifications.
Comments: In terms of Tactical 1911’s, I would saye the KJWorks KP-16 GBB Airsoft Pistol is one of my favorites out there. I really like the tan with dark highlights and the way KJWorks decided to match up the metal grips with the compensator with what I would call a dark chrome look to them. The KJWorks KP-16 GBB Airsoft Pistol really does look like it is right out of a video game or movie but if you want to dress it down a bit you can also remove the compensator to make it look more like most other Tactical 1911’s. I guess all that’s need to do now is test the KJWorks KP-16 GBB Airsoft Pistol out in the Replica Airguns Sea Can Range and see how well it performs!
My Table Top Video of the KJWorks KP-16 GBB Airsoft Pistol:
I have a nice Airgun Pistol Update Unboxing video to checkout where I take a look at 5 Airguns four of which are Gas Blowback Airsoft Pistols and one is a CO2 BB Revolver. I don’t go into a lot of details here on each Airgun as this is mainly just a preview video to let everyone know we have these products in our Online Replica Airgun Stores and give a you a quick look at them. I will be following up with individual Table Top and Field Test Videos where I go into more details and also show you how each gun performs in the Replica Airguns Indoor Sea Can Shooting Range.
Back in 2017 I made “Which Beretta Airgun is the Best” Video and showed off some 4.5mm Steel BB and .177 Caliber Pellet versions of my favorite Beretta 92 - M9 style Air Pistols. There have been some changes since then most noticeably the addition to Airsoft versions so I thought I would update this video with more current Beretta Airguns along with of course some of the same ones form my last video.
Because I show off 4.5mm Steel BB, .177 Caliber Pellet and 6mm Plastic Airsoft versions I decided to pick my favorites form each category. Watch my Vimeo Review Comparison Video so checkout these Air Pistols and see which ones are my favorites…
.177 Caliber Pellet Beretta 92 -M9 CO2 Air Pistols
In this Update Preview Unboxing Video I take a look at 5 products that came across my table and that I have not reviewed so far on the Replica Airguns YouTube channel.
First I show off an HPA tank from Air Venturi that works perfectly for the Sig Sauer MPX and MCX Pellet Rifles allowing for more consistent fps and I would image a higher overall fps? We will find out when I test it out in the replica Airguns Indoor Sea Can Airgun Range.
13 Oz Aluminum
10 Inches Long
2 Inches Diameter
Integrated Pressure Gauge
Includes Buttstock
CO2 Adaptor Included
3000 PSI Fill
1100 PSI Regulated
Next I take a look at the KJWorks M9A1 GBB Airsoft Pistol, I hover revived the CO2 version before but this version comes with the Gas magazine rather than the CO2 mag for those that prefer gas operated Blowback Airsoft Pistols. Because of the slightly lower FPS the Gas version comes with a barrel extension to make it Canada import friendly.
6mm Airsoft BB’s
Green Gas / Propane
370 fps
25 Round Magazine
2 Pounds
Probably one of the most interesting product I look at in this video at least for me is the EMG JW3 Combat Master GBB Airsoft Pistol. This Airsoft pistol is mainly aluminum with some polymer based off of the 2011 STI and was featured in the 2019 John Wick 3 Film. I’m really looking forward to testing this one out in the Sea Can Replica Airguns Airgun Range!
6mm Airsoft BB’s
Green Gas / Propane
9.4 Inches
366 fps
28 Round Magazine
2.4 Pounds
Moving along to another Air Pistol I finally get my hands on the Crosman P1 which is really just a KWC PT92 4.5mm Blowback CO2 BB Pistol but with Crosman Branding and an included laser. Since I have never shot a PT92 BB Pistol with a laser I will probably make a Field Test Shooting Video to see how well it performs.
4.5 mm Steel BB’s
CO2 x 1
4.2 Inch Barrel
330 fps
19 Round Magazine
2.4 Pounds
Comes with Laser Sight
Last up I take a look at the ASG TAC-6 which is pretty much the exact same ASG TAC-4.5 CO2 Air Rifle I tested a while back but in this case the 6 refers to it being a 6mm Airsoft Rifle rather than a 4.5mm Steel BB Riffle. I am not sure I will do a full Table Top Video since these guns are virtually identical but just in different Ammo types but I hope to get outside and see how well it performs shooting at a bit more distance than the 30 foot indoor range I usually test my Airgun in.
As promised this week, here is my full Field Test Shooting Video for the KJWorks KP-08 CO2 Airsoft Pistol. Make sure to watch my Table Top Review of the KJWorks KP-08 CO2 Airsoft Pistol if you’re looking for more details and specifications along with closeup video.
Starting with finding out the raw real world power for the KJWorks KP-08 CO2 Airsoft Pistol, I performed the Chronograph Test using my CaldwellBallistic Precision Chronograph and put 6 shots through it using a brand new 12 gram CO2 along with .20 gram plastic Airsoft BB’s. I was able to average 350 fps which is pretty decent considering it was only around 15 degrees Celsius (60 degrees Fahrenheit). In warmer summer conditions I am sure we would easily reach around 360-370+fps.
Next up I placed a paper target on my ammo trap 30 feet down range and shot off 10 steady paced rounds to see what kind of grouping I could get from the KJWorks KP-08 CO2 Airsoft Pistol. There is always going to be a bit of human factor involved since my Airguns are not braced in a vice or hold of any kind other than my two handed rested grip. (Sandbag upfront, sitting on a stool in the back). I was pleased to see a roughly 3 inch grouping on the target. There was one BB that did shoot a little bit higher then the rest of the grouping otherwise it would have been closer to a 2 inch grouping. I di notice that I was shooting a bit under the bullseye but this could are easily rectified by adjusting the hope slightly to add some more backspin to the Airsoft BB.
All in all I really like the KJWorks KP-08 CO2 Airsoft Pistol, it looks great, is well built, is not going to come in super heavy and seems to perform very well in terms of power and accuracy. I have always been a fan of the 1911 pistol and I like that KJWORKS didn’t deviate too much form the original A1 look and feel with this slightly more tactical version. It still looks and feels like a classic 1911 but is upgraded enough to keep the weight down while adding in a double stack styled magazine with more overall tactical features.
Trigger Pull: The trigger pull on the KJWORKS KP-08 CO2 Airsoft Pistol is what you would expect from a true 1911 single action only trigger, it has very little take up with a smooth crisp and light release to it The grip safety like a real 1911 also works on the KJWORKS KP-08 so it will needed to be engage in order for the trigger to function.
Accuracy: I have not shot the KJWORKS KP-08 CO2 Airsoft Pistol so far but plan to do so this week so I can have my Full Field Test Shooting Video Review for you ASAP. Keep posted as I this is next on my list!
Build Quality: I have always been extremely impressed with the build quality of all the KJWORKS Airsoft guns to date. The fit and finish is the best around compared with any of my airguns including my 4.5mm steel BB shooters. I would say KJWORKS and KWA Airsoft Guns are comparable in terms of build quality, fit and finish so it’s great we now offer both brands for you to choose from.
Realism: The KJWORKS KP-08 CO2 Airsoft Pistol is a replica of a High Capacity styled tactical 1911 45 Auto and is a great looking and functioning replica. You will not find actual Colt or other manufacturer licensing other than KJWORKS on this pistol and the CO2 magazine does stick out a bit to accommodate the 12 gram CO2 but other than that this Airsoft pistol looks and works near exactly like a real 1911 tactical 45 semi auto and is fully field strip-able. I really like the updated more tactical add ons like the tactical rail, machined trigger and hammer, white dot adjustable sights, and much lighter polymer frame that helps keep the overall gun weight down to around 2 pounds.
Metal parts where you need them, polymer frame to keep it lighter weight.
Heavy Full blowback operation.
Excellent fit and finish as always with KJWorks pistols.
High capacity full size drop out magazine that holds 28 rounds.
Versatile magazine options, also works with Marui Hi-Capa Magazines.
Easy to see white dot sights and adjustable for windage rear sight.
All working components like the real steel 1911.
Clean looking but still has that tactical quality about it.
Field strip-able.
Cons:
Grips are wider than a typical single stack 1911, may not fit the hands of small shooters.
No ambidextrous safety, not a problem for right handed shooters but lefties would benefit from this.
Comments:
The KJWORKS KP-08 CO2 Airsoft Pistol is KJWORKS first Airsoft pistol with a polymer frame. It’s also very versatile in that you can use KJWORKS KP-05 magazines and even High-Capa Marui Mags if you won them. The red internal gas tube allows you to use pretty much any type of magazine too which means Green gas, propane and CO2 are all good to go with the KJWORKS KP-08 CO2 Airsoft Pistol! The polymer frame really helps keep what would normally be a rather heavy Airsoft pistol a bit bit more light weigth and field friendly but you still have all the perks of a High-Capa 1911 so it’s a win win for me.
If you haven’t already watched my Table Top Comparison Review for the KWA M226-LE and KJWorks KJ1060 Sig Sauer P226 Airsoft Pistols than make sure to have a look at that video if you’re interested in more of the specifications and details and some closeup shots of both Airsoft Guns.
In this Field Test Shooting Video Review I compare the KWA M226-LE and KJWorks KJ1060 Sig Sauer P226 Airsoft Pistols head to head and side by side to see how these two very similar Sig Sauer P226 Airsoft Replicas perform. They both cost about the same, are built with similar quality and look a lot alike but what I really wanted to know is how do they shoot!
First off I tested out the power of both Airsoft Guns shooting 5 consistent .20 gram Airsoft BB’s from each gun through my Chronograph. Keep in mind I was using a full magazine of propane gas in the KWA M226-LE and a brand new 12 gram CO2 in the KJWorks KJ1060 (KP-01). As CO2 is know to have more power than green gas I was expecting a bit more pop out of the KJWorks KJ1060 which I did get. The temperature in my indoor Sea Can Airgun Shooting Range was 18 degree Celsius (64 degrees Fahrenheit) so not too cold or too hot. The KWA M226-LE averaged right around 320 fps while the KJWorks KJ1060 averaged 350 fps.
Moving on to my accuracy portion of the test for the KWA M226-LE and KJWorks KJ1060 Sig Sauer P226 Airsoft Pistols. I placed fresh paper targets 30 feet down range for each Airsoft pistol and put 10 rounds into each target shooting from a rested seated position. I did not adjust the hop-up or sights for either Airsoft Pistol prior to this test to see how close to the bullseye they would get out of the box. First up was the KWA M226-LE and it performed nicely for me shooting close to the bullseye, just a little bit low but getting around a 3.5 inch 10 round group. I then followed up with the KJWorks KJ1060 (HP-01) and also shot fairly near the Bullseye out of the box but the grouping opened up just a bit resulting in a 4.5 inch 10 round group. Still respectable for a close Airsoft quarters sidearm.
At the end of the day, the KWA M226-LE and KJWorks KJ1060 Sig Sauer P226 Airsoft Pistols came out pretty close to each other in this head to head Filed Test Shooting Comparison Review. One shot a little bit harder while the other one was a little bit more accurate but neither was a standout in either category. I guess you’re going to have to flip a coin deciding on which one of these two very well made Sig Sauer P226 Airsoft Pistols you’re going to choose but either way you will be getting a winner here.
Type: 6mm Plastic BB Airsoft Pistols. Manufacturer:KWA & KJWorks Model:KWA M226-LE - KJWorks KJ1060 (Sigt Sauer P226) Materials: Metal slide & frame. Weight: About 2.5 pounds. Barrel: Metalnon-rifled smooth bore. Propulsion: Green Gas - 12 Gram CO2. Action: Single and double action. Ammunition Type: 6mm plastic Airsoft BB's. Ammunition Capacity: 24-25 rounds. FPS: 350-400 fps
Trigger Pull: The trigger pull on both the KWA M226-LE and KJWorks KJ1060 Sig Sauer P226 Airsoft Pistols is very similar, they both shoot in single and double action and both actions are fairly light on the finger. I found the KWA M226-LE had a bit lighter double action trigger while the KJWorks KJ1060 seemed lighter when shooting in single action. This is all based on simply dry firing both guns to see who the triggers felt in both their single and double actions.
Accuracy: So far I have not shot either Sig Sauer P226 Airsoft Pistol but plan to get to my Field Test Shooting Review very soon. I will be testing both Airsoft Guns out head to head to see how each performs against each other for power and accuracy.
Build Quality: The build quality for the KWA M226-LE and KJWorks KJ1060 Sig Sauer P226 Airsoft Pistols is excellent. Both KWA and KJWorks make exception quality Airguns so which ever one you pick will be a good choice here. Both Airsoft Sig Sauer P226 Pistols are all metal full Blowback ultra realistic Airguns It may just come down to a few small differences. Overall I liked the fit and finish on the KWA M226-LE just a little bit more but it was very close.
Realism: In terms of realism it does not get any more realistic than this. You are going to find that the KWA M226-LE and KJWorks KJ1060 Sig Sauer P226 Airsoft Pistols mimic a real Sig Sauer P226 very closely with working parts as you would find them in the real steel version. The only tell tale sign on the KWA M226-LE is the orange tip which by they ways was not what we ordered so in future versions they will not have orange tips. The KJWorks KJ1060 comes with a CO2 magazine which is a bit elongated from the pistol grip but there are shorter Green Gas magazines for this gun available.
I like that both guns have full blowback operation, full size drop out magazines, easy to use white dot sights.
Working de-cockers and true to form single and double action triggers.
I like the finish on the KWA M226-LE, it’s smoother and has stamped in branding on the slide and frame.
I like the Grips on the KWA M226-LE, more ergonomic and comfortable.
Fit and overall quality feels just a little bit better on the KWA M226-LE.
I like the look of the flush green gas magazine on the KWA M226-LE.
I like the additional power the CO2 Magazine will give the KJWorks KJ1060.
I like that the KJWorks KJ1060 doe snot have an orange tip.
I like the the KJWorks KJ1060 comes with a speed loader.
What I dislike about each gun:
I don’t like that either gun doe snot have adjustable sights.
I don’t like the orange tip on the KWA M226-LE.
I don’t like the way the extended CO2 mag looks on the KJWorks KJ1060
Comments: No matter which of these two awesome Sig Sauer P226 Airsoft Pistols you may choose, you are going to love it. I am a big Sig Sauer fan and so it makes sense for me to own something like this so I can shoot it any time I want without having to go to the actual gun range and spend a boat load of money firing off real 9mm ammo. You really do get a very realistic experience shooting these ultra realistic Airsoft Pistols. They are the same size and weight, all the controls work the same, the triggers have the same weigth and feel to them, the blowback action simulates the recoil. The only difference is the cost to shoot, less recoil feel obviously and the fact that most people can shoot them safely and quality in the privacy of their own back yards.
My Table Top Comparison Review of the KWA M226-LE & KJWorks KJ1060 Sig Sauer P226 Airsoft Pistols:
I don't get many Gas Blowback Airsoft Rifles to review all that often so when I get my hands on them I sure have a great time testing them out and feeling the blowback action tapping me in the shoulder as I shoot in semi or full auto modes. Sure Gas Blowback Airsoft Guns don't perform like their AEG counterparts, especially when you're shooting in full auto. You can expect way less rounds in each magazine and even with less rounds the last 5 or 10 shots when shooting rapid fire are going to be compromised but I really don't care because a well made Gas Blowback Airsoft rifle like the KJWorks M4 CQB Carbine GBB is just so much more fun to shoot than an AEG and way more realistic.
So let's get on with my test results for the KJWorks M4 CQB Carbine GBB Airsoft Rifle... The fps consistency was really decent, super consistent when I spaced out my 5 test shots they averaged 377 fps, not really having any low or high fps shots out of the bunch. I did have a full gassed up mag and was using .20 gram plastic 6mm Airsoft BB's for this part of the field test.
Again shooting in semi auto mode, I placed 10 rounds into my paper target setup downrange 30 feet and as per usual I was using a rested shooting setup sitting on a stool and resting the KJWorks M4 CQB Carbine GBB Airsoft Rifle on a sandbag up front. 9 out of the 10 rounds all grouped in about a 3/4 inch group with only 1 round coming outside a bit stretching the 10 shot grouping out to about 1.5 inches. Still really great for a Gas Blowback or any Airsoft rifle for that matter!
Next I shot the rest of the mag in full auto burst mode which was about 20 rounds left in the KJWorks M4 CQB Carbine GBB Airsoft Rifle at this point. As expected the KJWorks M4 CQB Carbine GBB Airsoft Rifle cooled down pretty quick and the last 5 rounds did fire just fine but there was a noticeable drop in power making the rounds shoot low on the target. Keep in mind I was shooting in a not too warm environment, about 15 degrees which is not bad but also not that warm.
I would have liked to have seen the KJWorks M4 CQB Carbine GBB Airsoft Rifle perform as consistently in full auto mode as it did in semi auto but that would have been asking a bit too much from a Gas Blowback Airsoft rifle. The KJWorks M4 CQB Carbine GBB Airsoft Rifle is a really well put together Airsoft Rifle that didn't let me down in the end.
It's been a great year for Replica Airguns and I wanted to share with everyone some of my favorites that I reviewed this year. In this Vimeo Video I show some of my top Replica Airgun picks for 2016 and talk a little bit about each one and what I like about it.
Here is a list of the Replica Airguns in this lineup:
It has been a while since I picked out some of my favorite guns, after all my favorite gun picks change on a daily basis since there are so many awesome guns out there to pick from.
This Vimeo video is a little different since I pick out my favorites from a bunch of mostly replica gun categories including Steel BB, Pellet, Airsoft, Revolvers and Blank Pistols.
You may notice most of my picks happen to be blowback guns but to me airguns are all about being as realistic as possible and having blowback operation to me help to simulate the realism that much more. The exception in this video is in the pellet gun category since I decided on a pellet gun that was more about function and purpose over being any type of real replica.
Hopefully you take the time to watch my entire Vimeo video since I also bring out some close runner ups but here is a list of my top picks on this day, tomorrow it could be a completely different list of guns ;)
In this Field Test Shooting video I test out the KJWorks KP-11 Hi-Capa 1911 CO2 Blowback Airsoft Pistol to determine what the real work velocity is and also how well it performs in terms of accuracy. To test velocity I use a my Chrony Chronograph and do my best to get 5 good readings which I then average out. I always use a brand new 12 gram CO2 cartridge and generally use .20 gram plastic Airsoft BB's for my entire Field Testing. To test accuracy I set myself up 30 feet back using a semi rested position, to do this I place a sand bag to rest my hand and gun on and then stand securely in the back while I place 10 rounds on a paper target. There is obviously some humane factor involved but I can usually get a good idea on how accurate a given gun is.
During the Velocity or Feet Per Second Chronograph testing, I did manage to get 5 good readings, not all in a row but all within the first 10 or so shots. The KJWorks KP-11 Hi-Capa 1911 CO2 Blowback Airsoft Pistol shot hard and averaged 420fps again using .20 gram Airsoft BB's.
For my accuracy testing, all 10 shots placed within about 3 inches and they where fairly well centered left to right but did shoot a little bit high, this could be corrected using the hop-up adjustment to bring the Airsoft BB's down just a little.
I was rather surprised at how loud the KJWorks KP-11 Hi-Capa 1911 CO2 Blowback Airsoft Pistol is, it is by far one of the loudest CO2 Pistols I have shot to date other than the Umarex Desert Eagle Pellet Pistol. The KJWorks KP-11 Hi-Capa 1911 CO2 Blowback Airsoft Pistol also has a lot of blowback kick which makes it a lot of fun to shoot. Don't expect a lot of shots per CO2 since it uses a lot of CO2 per shot but in my books it is worth it for the added blowback recoil.
The KJWorks KP-11 Hi-Capa 1911 CO2 Blowback Airsoft Pistol may shoot a little bit hot for indoor Airsoft close quarters games but if you plan to use it outdoors at longer ranges it would definitely send Airsoft BB's out to further away targets. You could also pickup a Green Gas Magazine to lower the FPS about 50fps or so which would calm the KJWorks KP-11 down enough for indoor shooting.
Trigger Pull: The trigger pull on the KJWorks KP-11 1911 is very good since it is modeled after a real steel 1911 which makes it short and crisp with a nice light trigger pull. There is a very slight take-up at the very beginning of the pull but once your get past this the release is crisp and predictable. Since it is not a double action trigger you will need to either rack the slide for your first shot or pull the hammer back if you have already chambered a round.
Accuracy: I have not done my actual Field Test Shooting video review for the KJWorks KP-11 M1911 Airsoft Pistol so I do not have any definitive feedback for you but based on my experiences shooting other KJWorks 1911 styled Airsoft CO2 Pistols I expect it to have great blowback action recoil, a nice trigger and good overall FPS and accuracy. In terms of reliability, KJWorks pistols are solid in this department.
Build Quality: As expected, the KJWorks KP-11 Hi-Capa 1911 CO2 Blowback Airsoft Pistol build quality is exactly like all the other KJWorks Airsoft guns I've tested so far, Build quality for the price point is top notch with tolerances between the moving parts like the slide and frame are extremely tight showing excellent workmanship and machining from KJWorks. The finish is always a step above other similar styled Airsoft and BB guns, youn really don't have to worry about the finish coming of as easy.
Realism: The KJWorks CO2 KP-11 Hi-Capa 1911 Blowback Airsoft Pistol copies the real steel very popular even today Colt 1911 45 caliber pistol, it can be field stripped very similarly to a real 1911 Semi Auto pistol and all parts function virtually the same including a working safety, grip safety, slide catch-release, magazine release and hammer. This Hi-Capa version has a more tactical look with a wider frame for what would be a double stack hi capacity styled magazine.
Has really good weight but not too heavy since it has a polymer frame..
Expect to have typical KJWorks crisp and firm full blowback operation.
Excellent fit and finish. I like the mat textured finish which looks to bed super durable.
Nice bright white dot sights, really easy to see.
I like the look of the tactical hammer and trigger.
Nice high capacity magazine with a little extra zing for the CO2 Mag.
Fully field strip-able.
Cons:
Is not really setup up for left handers with no real ambidextrous components.
CO2 magazine is long to accommodate the 12 gram CO2.
Grips may be a bit thick for smaller hands.
Comments:
I love 1911 pistols and enjoy shooting them, there is something about how they feel in the hand that is different form most other pistols. They always feel so solid. The KJWorks Airsoft versions capture that feeling exactly and again the little bit more you may pay for a KJWorks 1911 over some other lesser quality Full blowback 1911's is worth the cost in my books. This Hi-Capa 1911 version with it's tactical look and finish would make a great game player for sure!
My Vimeo Table Top Review of the KJWorks KP-11 Hi-Capa 1911 CO2 Blowback Airsoft Pistol:
I was personally confused about some of the similarities and differences between several models of KJWorks Beretta M9 CO2 Blowback Airsoft Pistols, so I decided to make a video where I go over 4 models of KJWorks M9 Pistols and point out the commonalities and differences between them.
Here are the 4 versions of KJWorks Beretta M9 CO2 Blowback Airsoft Pistols:
All of them come with interchangeable 25 round CO2 Magazines.
All of them shoot around 360+ fps.
All have a metal slide and frame.
All weigh close to the same weight (2.1 - 2.4 pounds).
All shoot in single and double action.
All have ambidextrous safeties.
All have white dot sights.
Prices range from $184 -$200.
Here is a list of the differences between them:
The VE, Vertex and M9A1 come in a semi gloss finish while the Tactical is more of a matt black.
The VE and M9A1 have rails for accessory attachments while the Vertex and Tactical do not.
The Vertec, Tactical and M9A1 have laniard loops while the VE does not.
Some slight trigger guard differences between the models but very subtle.
The Vertex and M9A1 share the same style classic Beretta pistol grip, The Tactical has a tactical finger pistol grip and the VE has it’s own unique pistol grip.
Make sure to watch my Vimeo video where I cover this information in detail:
Another Airsoft Pistol Preview Video to share with everyone. First up we have a nice lighter weight CO2 powered 1911 from KJWorks called the KP-11 The lower receiver is polymer which helps to keep this gun a little bit lighter all around but it still has good weight to it coming in at a little over 2 pounds, the grips are larger than some 1911's since the KP-11 has a double stack style full size drop out metal magazine. You will also find some nice Tactical upgrade like adjustable white dot sights, a lower rail for accessories and milled trigger and hammer.
I also show off an interesting and not all that common pistol from Cybergun, the FNX -45 Tactical in Gas Blowback. For import into Canada it ships with a longer barrel which stick out of the front of the gun but it also comes with a shorter barrel you can install after your receive it. The Longer barrel gives the Cybergun FNX -45 Tactical Airsoft Pistol the extra velocity to allow it to be Canada import ready. The FNX -45 Tactical is a really detailed and well built Airsoft Pistol. By the way the FNX -45 Tactical is also availabl in Dark Earth color.
Here are some of the specifications for the KJWorks KP-11 and Cybergun FNX -45 Tactical Airsoft Pistols:
Propulsion: Green gas or 12 Gram CO2 dependant on magazine used.
Action: Blowback,Single action only.
Ammunition Type: 6mm plastic Airsoft BB's.
Ammunition Capacity: 29 rounds.
FPS: 410-440 fps
Trigger Pull: The trigger pull on the KJWork KC-02 Version 2 10/22 Gas Blowback Airsoft Carbine is pretty much exactly like a real Ruger 10/22, nice and short, not to light or heavy, crisp and single action only. If you already have a Ruger 10/22 and want to pickup this Airsoft version for some anytime shooting then you will not be disappointed in the trigger since it is already what you are used to.
Accuracy: I decided to setup my paper target a little further out than my standard 30 feet, so I took it back to around 50 feet and put around 24 shots into it in a fairly quick succession from a rested position. The KJWork KC-02 Version 2 10/22 Gas Blowback Airsoft Carbine grouped continently and well centred on target getting around a 3 inch grouping. This was using a red dot scope but with the out of the box hop-up setting in place. I was a little bit surprised by my fps results as my Chronograph recorded an impressive 445 average 5 shot fps using the lower powered green gas magazine. All shot where within only a few fps of each other too! I can only imagine how hard this gun would shoot using the alternative CO2 Magazine. Blowback action was just enough to give some feedback and of course allowed for the bolt to cycle giving the KJWork KC-02 Version 2 10/22 Gas Blowback Airsoft Carbine a true single action trigger pull.
Build Quality: The build quality for all KJWork KC-02 Version 2 10/22 Gas Blowback Airsoft Carbine is very good with a nice weight and feel to it, It really does feel like I am holding a real Ruger 10/22 and it is one of the most popular semi auto 22LR rifles out there for a reason. Mechanically this Ryger 10/22 copy works great, super consistent and very responsive. The fit and finish as with all KJWorks guns is top notch.
Realism: The KJWork KC-02 Version 2 10/22 Gas Blowback Airsoft Carbine is for all intents and purposes simple an Airsoft version of the Ruger 10/22 and even though I have no way to confirm this, I would imagine many 10/22 after market accessories may actually work with the KJWork 10/22 Gas Blowback Airsoft Carbine. Everything works just like it would on a real 10/22 without the loud noise and ejecting shells.
Built on the very popular 10/22 platform so lots of people are going to be very familiar with this rifle and may want an Airsoft version they can shoot just about any time they feel like it.
Good weight and feel to it.
Blowback semi auto action with true single action trigger.
Lots of rail access points for tons of add on accessories.
Pop-up fully adjustable sights stay out of the way but are ready to go when needed.
Easy to adjust Hop-up.
Available magazines in both CO2 and Green Gas.
Adjustable AR styled rear stock with AR pistol grips.
Sling mounts included.
Works with standard Airsoft screw on flash hider or suppressors.
Awesome FPS and consistency.
Very accurate even at 50 feet, around a 3 inch 25 shot grouping.
Cons:
No full auto mode.
Higher capacity mag would have been nice.
Would be nice to have a higher capacity magazine for it.
Comments:
I am really impressed with the KJWork KC-02 Version 2 10/22 Gas Blowback Airsoft Carbine! It feel and shoots a lot like the real steel version but with less noise and recoil. For back yard shooting fun and practice you can not find a cheaper gun out there to simulate shooting your real 10/22 and of course this rifle used on an Airsoft field would be a perfect fir for almost any shooting environment since it is light, compact, accurate and powerful. I think I found my newest favorite Blowback Airsoft Rifle :)
My Vimeo Table Top Review of the KJWork KC-02 Version 2 10/22 Gas Blowback Airsoft Carbine:
