Todays video is all about “damage”! How much damage can each of these .50 caliber ball options deliver to an object and the object of interest in todays video are a couple of over rip pumpkins that needed putting out of their misery. Luckily when I made this video the weather outside was cooperating with me and I go tI nice break in the rain. This was awesome as I was not looking forward to al the cleanup I would of had to of done if I performed this test inside the Replica Airgun Sea Can Shooting Range.
This is part three of my three part Indoor Filed Test Shooting Video for the Umarex T4E P2P HDP 50 Gen 2 CO2 Less Lethal Pistol. In this third video I test out the velocity and energy shooting 5 rounds through my Chronograph using the 8 gram All Steel Balls that I purchased on my own to test with this Less Lethal Pistol. I also shoot 5 rounds of the same All Steel Balls into a paper target setup 30 feet down range to get an idea on what to expect accuracy wise with the Umarex T4E P2P HDP 50 Gen 2 CO2 Less Lethal Pistol. I have already uploaded Field Test Shooting Videos one and two where I test out 1.6 gram All Rubber Balls and 2.7 gram Rubber/Steel Balls. If you have not watched my Table Top Video for the Umarex T4E P2P HDP 50 Gen 2 CO2 Less Lethal Pistol, then make sure to do so for closer up video and all the specifications and details.
Umarex claims a max velocity of 485 fps with an energy rating of 13 Joules with the Umarex T4E P2P HDP 50 Gen 2 CO2 Less Lethal Pistol when using their supplied ammo. I am assuming this would be using the Powder Balls as they are the lightest option of Ammo that are included in the box with this pistol and will have the highest velcoity. In my Chronograph testing I shot 5 rounds using the 8 gram All Steel balls. The velocity for the 8 gram All Steel Balls was much slower than the 1.6 gram All Rubber Balls and 2.7 gram Rubber/Steel Balls as expected, but they did stay fairly consistent ranging from a low of 132 fps to a high of 151 fps, averaging 138 fps. The overall energy rating ended up being the slowest by far out of all the rounds I tested in this Less Lethal Pistol, with an energy rating of only 7 Joules. Based on energy alone I would suggest using the All Rubber Balls as they achieved the highest energy rating at 15 Joules, even higher than claimed by Umarex.
Now that we understand that the 8 gram All Steel .50 Caliber All Steel Balls are not only the lowest velocity by a long shot, they also have the lowest energy rating again by a lot as compared to the other rounds tested. Maybe when I compare the accuracy during my target Test the .50 Caliber All Reel Rounds may redeem themselves. After Shooting 5 of the 8 Gram All Steel Rounds into my Paper Target from a distance of 30 feet, I did actually get the tightest grouping, even with a heavily fading CO2 that was near it’s end, so velocity did taper off making the shots shoot lower and lower with each shot. I did throw the final 5th shot out as I could literally see it loft to the target but even with the low CO2 and inconsistent velocity, I got my best grouping from the Umarex T4E P2P HDP 50 Gen 2 CO2 Less Lethal Pistol with a 3 inch grouping just slightly to the left of the bullseye but very close.
I was not surprised with the performance of the Umarex T4E P2P HDP 50 Gen 2 CO2 Less Lethal Pistol using the 8 gram All Steel Balls for this third Field Test. Velocity was much lower as expected than the other lighter rounds tested, but most surprising, the energy was around half of the All Rubber Balls. Perhaps the metal rounds just did not reach their maximum speed in such a short barrel due to them being a so much heavier weight? My conclusion on Ammo choice for the Umarex T4E P2P HDP 50 Gen 2 CO2 Less Lethal Pistol would be to go with either the All Rubber Balls or the Rubber Steel Balls. The All Rubber Balls by far had the highest velocity and energy rating but I did feel like the Rubber Steel Balls even though they where moving slower and had slightly less energy, seemed to hit the target with the most force based on the sound I was hearing while performing the testing. Either round will for sure make an intruder think twice about continuing their course of bad behavior. I will probably do some testing on how each of these rounds effects different targets in the future, I just need to figure out what I want to shoot at…
This is part two of my three part Indoor Filed Test Shooting Video for the Umarex T4E P2P HDP 50 Gen 2 CO2 Less Lethal Pistol. In this second video I test out the velocity and energy shooting 5 rounds through my Chronograph, using the 2.7 gram Rubber/Steel Balls that I purchased on my own to test with this Less Lethal Pistol. I also shoot 5 rounds into a paper target setup 30 feet down range to get an idea on what to expect accuracy wise with the Umarex T4E P2P HDP 50 Gen 2 CO2 Less Lethal Pistol. In video three I plan to test out the 8 gram all Steel Balls to see they are a viable option with a CO2 Pistol like this designed for much lighter rounds . If you have not watched my Table Top Video for the Umarex T4E P2P HDP 50 Gen 2 CO2 Less Lethal Pistol, then make sure to do so for closer up video and all the specifications and details.
Umarex claims a max velocity of 485 fps with an energy rating of 13 Joules with the Umarex T4E P2P HDP 50 Gen 2 CO2 Less Lethal Pistol when using their supplied ammo. I am assuming this would be using the Powder Balls as they seem to be a bit lighter than the Rubber Balls and will have the highest velcoity. In my Chronograph testing I shot 5 rounds using the 2.7 gram Rubber/Steel balls. The velocity for the 2.7 gram Rubber/Steel Balls was slower as expected but they did stay fairly consistent ranging from a low of 300 fps to a high of 309 fps averaging 304 fps. The overall energy rating ended up being 12 Joules, so obviously lower in fps than claimed by Umarex but close to the claimed 13 Joules. Still a good result close to the claimed raw energy.
The main point to this ammo comparison video is to finds out not only if the heavier 2.7 gram Rubber/Steel Balls will have around the same energy as the lighter 1.6 gram all Rubber Balls, but also to see if they have similar accuracy. In terms of accuracy the 2.7 gram Rubber/Steel Balls did just a little bit better than the 1.6 gram all Rubber Balls, not by a lot but, by about 1 inch with a 5 round grouping of 5 inches. All 5 shots were well entered shooting just a bit high of my aim point by about 3 inches but in general well centered left to right as a grouping.
I was happy with the performance of the Umarex T4E P2P HDP 50 Gen 2 CO2 Less Lethal Pistol using the 2.7 gram Rubber/Steel Balls for this second Field Test. Energy was very close to the claimed 13 Joules and the average 304 fps I got with this ammo felt snappy and got to the target quickly and sounded like they really hit hard. I do like the higher 15 Joules and 450 fps I got from the lighter 1.6 gram all Rubber Balls, so at this point I would probably recommend sticking with them for the most power and energy down range. Next up I test out the 8 gram all Steel Balls to find out if they are even an option or if they are simply juts to heavy for the Umarex T4E P2P HDP 50 Gen 2 CO2 Less Lethal Pistol.
This is part one of my three part Indoor Filed Test Shooting Video for the Umarex T4E P2P HDP 50 Gen 2 CO2 Less Lethal Pistol. In this first video I test out the velocity and energy shooting 5 rounds through my Chronograph, using the 1.6 gram included Rubber Balls that came with it and then I also shoot 5 rounds into a paper target setup 30 feet down range to get an idea on what to expect accuracy wise with the Umarex T4E P2P HDP 50 Gen 2 CO2 Less Lethal Pistol. In video two I will be testing out the 2.7 gram Rubber/Steel Balls in the same way, and then in video three I will be testing out the much heavier all steel 8 gram rounds to see if they are even usable in a CO2 Airgun designed for much lighter rounds. If you have not watched my Table Top Video for the Umarex T4E P2P HDP 50 Gen 2 CO2 Less Lethal Pistol, then make sure to do so for closer up video and all the specifications and details.
Umarex claims a max velocity of 485 fps with an energy rating of 13 Joules with the Umarex T4E P2P HDP 50 Gen 2 CO2 Less Lethal Pistol. In my Chronograph testing I shot 5 rounds using the 1.6 gram included all rubber balls. I did throwout the first shot as it was about 50 fps lower than the rest, perhaps as it was first out of the barrel which can happen. The other 4 rounds averaged 445 fps with an overall energy rating of 15 Joules, so a bit slow in fps than claimed by Umarex but a higher energy output. Perhaps the fps rating was for lighter rounds like the included 10 powder balls? Still an excellent result with more raw energy than expected which is great for a system designed to deter an intruder!
What good is power if you can not hit the target? That’s why I always test out accuracy as you want your gun to shoot where you point it. With Rubber Balls they tend to “wing” or “curl” a bit in the air which does spread out the groupings a bit over a BB or even Airsoft gun, so I was not expecting under a 2 inch grouping. My goal was to hit the target fairly centered with around a 6 inch grouping and the Umarex T4E P2P HDP 50 Gen 2 CO2 Less Lethal Pistol did exactly that for me, so mission accomplished. I also wanted to find out how many shots to expect from a fresh 12 gram CO2 and my results showed around 20 shots, so you can reload the internal magazine around 4 times before the trigger stops working, which is how you know the CO2 pressure is not adequate enough to shoot any more rounds.
I was very happy with the performance of the Umarex T4E P2P HDP 50 Gen 2 CO2 Less Lethal Pistol using the included 1.6 gram All Rubber Balls for this Field Test. Energy was even 2 Joules higher than claimed by Umarex, and I did not have a single malfunction with this pistol through my testing of all types of ammo I used in videos 1, 2 and 3. I would say the Umarex T4E P2P HDP 50 Gen 2 CO2 Less Lethal Pistol is your best option as a Less Lethal Pistol here in Canada. Will it stop a very determined intruder? Maybe not, but I would feel a little bit safer with the Umarex T4E P2P HDP 50 Gen 2 CO2 Less Lethal Pistol at my side than not having it at all. And a couple well aimed rounds to some soft tissue will for sure make someone reconsider some of their life choices. Stay posted for videos two and three coming out shortly…
Type: Less Lethal Pistol. Manufacturer:Umarex - T4E. Model:P2P HDP 50. Materials: Metal & Polymer. Weight: 1.5 pounds (.7 kg). Barrel: 4 inches (10.2 cm) Smooth bore. Total Length: 8.5 inches (21.6 cm). Power Source: 1x12 gram CO2. Action: Semi auto - Double action only trigger. Ammo Type: .50 Caliber Rubber Ball, Pepper Ball, Powder Ball. Ammo Capacity: 6 Round spring fed internal magazine. FPS: 485 (13 Joules).
Trigger Pull: The trigger pull on Umarex P2P HDP 50 Gen 2 CO2 Less Lethal Pistol is double action only but not overly long or heavy. There does not seem to be any ammo friction which is nice, so the each round feels about the same with spring tension not playing a factor. In order to use the trigger, the Pistol will need to be fully charged by loading a 12 gram CO2 and giving it a smack on the bottom of the pistol grip. This will pierce the CO2, charging the gun with pressure and activation the trigger mechanism. When the CO2 pressure becomes too low, the trigger will not function and a fresh CO2 will needed to be swapped over.
Accuracy: So far I have only briefly tried out the Umarex P2P HDP 50 Gen 2 CO2 Less Lethal Pistol here in the Replica Airguns Indoor Airgun Shooting Range, and I was rather impressed at the initial performance as it did seem to be moving the .50 call rubber balls I was shooting at close to 500 fps with a lot of energy as my pepper and cardboard target was dislodged from the backstop after a few shots. Accuracy seems to be as expected from a Paintball type pistol, so I am expecting to get around a 4-6 inch 6 shot grouping at 30 feet away which will be effective in a Less Lethal encounter.
Build Quality: The build quality of the Umarex P2P HDP 50 Gen 2 CO2 Less Lethal Pistol is good overall. It is mostly made out of plastic which is fine, as I feel that if it was mostly metal, and because of its larger size, it would be on the heavy side and not something you may want to use in a cary situation if that was your plan. There is metal where it needs to be in most of the mechanical areas including the barrel, trigger, charging system and I am sure other internal parts. The plastic parts feel well made and fit and finish is very good. The Umarex P2P HDP 50 Gen 2 CO2 Less Lethal Pistol does have more than enough weight at 1.5 pounds to feel solid in the hand.
Realism: This version of the Umarex P2P HDP 50 Gen 2 CO2 Less Lethal Pistol comes with the orange slide to show that it is not a lethal firearm. I have seen all black version but at this time we only sell the colored slide version. This does make it obvious that the Umarex P2P HDP 50 Gen 2 CO2 Less Lethal Pistol is not a “Real Firearm” designed for lethal encounters, which in Canada is a good thing since our self protection laws seem to favor the criminal more than the victim. So making sure you are using a tool designed to deter a criminal rather than harm or kill them, is hopefully going to keep you out of trouble with the law. That said the Umarex P2P HDR 50 Gen 2 CO2 Less Lethal Pistol does look like a modern semi auto pistol and functions much the same but with less force.
Pros:
Not many options for a true less-lethal option here in Canada. This Airgun is purpose built for less lethal use so it has what I believe is enough power to actually dissuade most intruders.
In this case I like that it is clearly marked in orange to indicate it is not an actual lethal firearm. When protecting yourself in Canada you have to be cautious with your intentions, and having clear orange markings will help in your case to show that you where not trying to give the impression of using a real firearm.
Nice powerful 485fps with a 13 Joules energy rating.
Can store the 12 gram CO2 in it and activate with a quick hit to the bottom of the CO2 screw.
Holds 6 rounds in the internal magazine which hopefully gets the job done. Should be able to reload at least one more time for a total of 12 shots per 12 gram CO2.
Fiber Optic sights make it easy to line up your target in most lighting conditions and backgrounds.
Double action trigger feels smooth and not too heavy or long, also has a trigger safety on it.
Can add a tactical light or laser to the under barrel picatinny rail.
Comes with 10 rubber and 10 powder balls to get you started.
Cons:
It is a bit on the larger size, not going to be easy to cary if that is your plan. I do not know what the legal ramifications of carrying this would be as it is clearly designed for protection and not for lethal encounters.
Not a lot of shots per CO2 but the idea here is to quickly deliver as much damage as possible, this is not a weapon for prolonged gun fights.
In Canada it does not seem you can get pepper balls easily most likely due to import regulations.
Comments:
The Umarex P2P HDP 50 Gen 2 CO2 Less Lethal Pistol is a very refreshing product for us here in Canada as up until now similar styled Rubber Ball purpose built self defense products we have been able to get, in my opinion simply did not have enough power to really be effective other than the initial intimidation of holding what looks like a firearm. If it came down to actually shooting it, I don’t believe there would be enough stopping power to deter an intruder. The Umarex P2P HDP 50 Gen 2 CO2 Less Lethal Pistol on the other hand has a 485 fps, 13 Joules power rating which is a rather big jump from other similar products available to us here in Canada and although it may not stop everyone, I do believe you have a much better chance protecting yourself with the Umarex P2P HDP 50 Gen 2 CO2 Less Lethal Pistol. If you are looking for something to have at home to help you feel a bit safer, then the Umarex P2P HDP 50 Gen 2 CO2 Less Lethal Pistol is the absolute best option for Canadians at this time.
This was a really fun Unboxing Video for me as I received something I feel a lot of Canadians might be really interested in protecting yourself in Canada is not a right especially if you use lethal force. So having a less lethal option is a really good idea.
Let’s get into what I found in this most recent Mystery Box in order of appearance…
The first item I unboxed was the KWC SP2022 CO2 NBB 4.5mm Steel BB Pistol. A pretty basic 4.5mm CO2 BB Pistol mostly made out of plastic but with a full size 21 round drop out metal magazine that does help a lot to add some much needed weight to this Airgun. It uses standard 12 gram CO2 with a claimed velocity of 450 fps.
Probably the most exciting item I pulled out of this months Mystery Box was the Gen2 Umarex P2P HDP 50 Rubber Ball purpose built Less-lethal solution for personal and family protection. Most of the similar Rubber ball Less-lethal Airguns I have tested generally do not pack enough punch to really be much of a deterrent in my opinion but the Gen2 Umarex P2P HDP 50 has a claimed 495 fps and when I tested it out after making this video it defiantly has some power. I would not want to be at the receiving end of this product especially in close proximity. The Gen2 Umarex P2P HDP 50 uses a traditional 12 gram CO2 and holds 6 rounds of rubber ball or powder ball, it does come with 10 of each to get you started.
Next I took a look at three KJWORKS Airsoft Pistols all of which came with CO2 Magazines, extension barrels and thread on tips. The KJWORKS KP-19, the KJWORKS M9A1 TBC, and the KJWORKS KP-13 TBC. As expected with KJWORKS Airsoft Guns, they looked really good and will be a joy to review and test out.
Last out of the Mystery Box was a new product from Umarex, a full sized Marlin Cowboy Lever Action BB Rifle in the style of the classic Red Ryder BB Gun but as mentioned in a larger size more suitable for an adult. Hey why do the kids get to have all the fun? The Umarex Marlin BB Rifle holds 650 rounds in its BB hopper and has a claimed fps pf 300. It also has an adjustable for elevation peep sight in the back with a metal lever and a Classic Faux Wood Finish.
Type:AEG Airsoft Rifles Manufacturer: G&G. Model:RK Beta AK Materials: Mostly metal/some plastic. Weight: 7.1 pounds (3.2 kg). Total Length: 28.5 inches (72.4 cm). Barrel: 9 inches (22.9 cm) barrel non-rifled. Propulsion: AEG. Action: Single action semi & full auto. Ammunition Type: 6mm plastic Airsoft BB’s. Ammunition Capacity: High cap 600 round magazine. FPS: 390 fps.
Trigger Pull: The trigger pull on the G&G RK Beta AK AEG Airsoft Rifle is short and light as it is basically a simple electric on/off switch that completes a circuit and tells the motor to turn, which activates the cycling of the spring piston. For this reason there is no real creep or feel of a release. When you get to a preset point in the trigger, the motor circuit is closed allowing for either semi or full auto, depending on your selector switch position at the time.
Accuracy: I will be making a dedicated Field Test Shooting Video for the G&G RK Beta AK AEG Airsoft Rifle to find out what the actual velocity is in fps. I will also test what kind of accuracy I can get shooting a paper target in both semi and full auto from 30 feet away. For now I have no idea what to expect but as this is most certainly not a cheap Airsoft AEG Rifle, I am hoping for good results to justify the higher price point.
Build Quality: The build quality of the G&G RK Beta AK AEG Airsoft Rifle is very good, G&G Airsoft Rifles in general are well built. You are going to find metal in most of this AEG Airsoft Rifle including the receiver, dust cover, trigger guard, trigger, selector switch, barrel, front and rear sights and the magazine. The only plastic to be found will be in the pistol grip, rear stock and 3 of the picatinny rails. Fit and finish is very good but the stock and pistol grip material does seem to show scratches really easily.
Realism: The G&G RK Beta AK AEG Airsoft Rifle is a 1 to 1 scale Airsoft reproduction of the AK 47/74 in a compact modernized version. I don’t believe it is based on exactly one specific brand or type of AK 47 or AK 74, but is more or less a stylized version designed and built by G&G. The G&G RK Beta AK AEG Airsoft Rifle does have a lot of metal and weight to it adding to the realism and most of the mechanical parts work similar to a real steel version of an AK 47/74. G&G has added a bit of a bolt cycle motion with a motor that actuates it to some degree but this is not like the look and feel of a real internal bolt from an actual AK 47/74. Still a nice touch.
Pros:
Lots of metal in construction where you need it with good overall weight and feel.
6 rail attachment options up front for lots of mounting positions.
Left side option to attach an additional AK style sight mount.
Adjustable front sight for elevation.
Nice and compact for easy maneuverability.
Rear stock has lots of room for battery sizes and options.
Dust cover comes off for easy access to internals.
G&G high quality build.
Comes with sling mounting options.
Super easy hopup adjustment slider.
Nice high capacity 600 round metal magazine.
No orange tip.
Cons:
Rear sight is all but useless.
Stock and grip scratch really easily.
Priced on the higher side.
Comments:
The G&G RK Beta AK AEG Airsoft Rifle may be priced a bit on the high side for some people but it is a solid AEG Airsoft Rifle and it seems there are not as many AK options out there so it is nice to have an offering from G&G. I like the almost full metal construction and I find the modernized styling and compact size to be appealing and would make it a great option for CQB Airsoft games. I am not sure what is going on with the rear site, as it looks like it is a sight, but does not have the sight grove in it? Maybe I am missing something here but other than opting to put a red dot way up front, your only other option is to put an AK side rail and mount a sight on the rear just above the metal dust cover. I am hoping when I make my Field Test Shooting Video for the G&G RK Beta AK AEG Airsoft Rifle, it performs well for me to justify the higher price point.
My Vimeo Table Top Review for the G&G RK Beta AK AEG Airsoft Rifle:
Here we go with another unboxing video this month, and this is a big box, so no doubt the mystery items are going to be big too! As always with new products, I will be following up with dedicated Table Top and Field Test Videos for each of them so make sure to check down the road for those videos for a lot more information and actual performance results…
Don’t look below if you want to just watch the video and be surprises by what’s inside the mystery box but if you want a quick peak before hand then checkout the basic specs below for all three new items I will be reviewing soon.
Type:AEG Airsoft Rifles Manufacturer:Umarex. Model:Elite Force M4 CFRX Materials: Mostly plastic/some metal. Weight: 5.2 pounds (2360 grams). Total Length: 32.4-35.4 inches (820-900mm). Barrel: 16.1 inch (410mm) barrel non-rifled. Propulsion: AEG. Action: Single action semi & full auto. Ammunition Type: 6mm plastic Airsoft BB’s (Eye Trace compatible). Ammunition Capacity: Mid/High cap 340 round magazine. FPS: 370-400 fps.
Trigger Pull: The trigger pull on the Umarex Elite Force M4 CFRX Eye Trace AEG Airsoft Rifle is fairly short and light as it is basically a simple on and off switch as it is not mechanical but rather electrical. For this reason there is no real creep or feel of a release. When you get to a point in the trigger you close a circuit that activates the electric motor cycling the spring shooting in either semi or full auto depending on your selector switch position at the time.
Accuracy: At this time I have not made my Field Test Shooting Video or even shot the Umarex Elite Force M4 CFRX Eye Trace AEG Airsoft Rifle, I am planning to make a video for this rifle at the end of this week if all goes as planned. I do not have any of the “Eye Trace” Airsoft Ammo to show how this works and looks but I will be able to do my traditional accuracy and velocity testing here in the Replica Airguns Indoor Sea Can Airgun Range. When I do get access to some of the Eye Trace Airsoft Ammo I will make a short video most likely in a lower light situation to show how it looks.
Build Quality: The Umarex Elite Force M4 CFRX Eye Trace AEG Airsoft Rifle does have a lot of plastic in the build including the upper and lower receiver, hand guard, rear stock, front and rear sights, grips and flash hider but as expected there are metal part where they are required as in the inner and outer barrel, magazine, buffer tube, trigger, selector switch, magazine release, charging handle, dust cover and of course many internal parts. It does have a decent weight to it being a fairly long AR and so it feels solid enough. I would have liked to have seen metal sights and perhaps a metal receiver since it is not a cheap or inexpensive AEG Airsoft Rifle.
Realism: The Umarex Elite Force M4 CFRX Eye Trace AEG Airsoft Rifle is based on the M4/M16 platform of course in a modern version with all the tactical additions. It looks and feels the part for sure with lots of working parts including the safety, selector switch, charging handle, dust cover, adjustable rear stock, pop-up front and rear sights as you would expect. Most of the hardware should be interchangeable with a real steel AR if you want to personalize the look of it. The addition of the Tracer element will add to the realism when shooting it in low light situations, but so far I have not tested it as I do not have any Eye Trace Ammo on hand.
Pros:
Eye Trace System unique and great in low light situations.
Lots of accessory mounting options with Picatinny top rail and side adb bottom M-LOK.
Full adjustable Pop-up sights.
Pre-installed MOSFET for improved electronic performance.
Ver 2 Full Metal, fully upgradeable gearbox.
6 position adjustable AR compatible type rear stock.
I like the two tone black and tan finish.
Has the Elite Force Branding from Umarex.
Easy to get at adjustable Hop-up.
Cons:
Plastic receiver and orange tip.
Battery options limited due nunchuck compatible space.
Pop-up removable sights are plastic.
Comments:
Umarex introduced the “Eye Trace” line of Airsoft Rifles at SHOT Show this year and I have been somewhat eagerly awaiting getting my hands on one to try this new system out, but unfortunately we do not have any of the Eye Trace Airsoft Ammo to do that with. I am not sure if Umarex is low on supply or perhaps it was missed in the order? Either way I will be testing out the new Eye Trace Airsoft Ammo when I get my hands on some. in the future. Just to be clear on how this works, the Eye Trace Ammo is florescent and these New Eye Trace Airsoft Rifles have a blue light you can turn on or off that activated the florescent Airsoft Rounds illuminating them to look like tracer rounds coming out of your barrel. The new Eye Trace Airsoft Rifles work just like a standard AEG Airsoft Rifle when using normal Airsoft BB’s, so I can test the Umarex Elite Force M4 CFRX Eye Trace AEG Airsoft Rifle as I always do so stay posted for my Official Field Test Shooting Video for it coming out very soon.
My Vimeo Table Top Review for the Umarex Elite Force M4 CFRX Eye Trace AEG Airsoft Rifle:
Here is video four in my series of Full Auto Fun videos I make each summer where I pick a few Full Auto Airguns and record some fun outside shooting with them. In this years Full Auto Fun Video series I do a bit of a walk around on my property and shoot a bunch of water filled pop cans. Maybe this doesn’t sound super exciting but I do use some really creative camera angles to capture it all which makes it lot more interesting to watch for sure!
In this fourth Full Auto Fun video, I retest the Barra 400e 4.5mm BB AEG Full Auto BB Rifle in full auto this time, and try a bit of a different camera angle approach with my HoverAir Drone Camera switching it to follow mode as it doesn’t stop recording so easily in this mode. And as expected, it worked a lot better for me with this setup and continued recording the entire video. I also recoded using my Meta Glasses to get the first person view and like the other videos I placed my Insta360 X4 camera on the barrel again to get some cool up front gun angle shots. I think this setup works well and will probably use it for future Full Auto Fun Videos where I am running around the yard shooting stuff. Maybe there will be a couple more bonus guns in this years Full Auto Fun Series? No promises!
I try to make at least one series of Full Auto Fun video each summer where I pick a few Full Auto Airguns and record some fun outside shooting with them. In this years Full Auto Fun Video series I do a bit of a walk around on my property and shoot a bunch of water filled pop cans. Maybe this doesn’t sound super exciting but I do use some really creative camera angles to capture it all which makes it lot more interesting to watch for sure!
In this first Full Auto Fun video I start with the Barra 400e 4.5mm BB AEG Full Auto BB Rifle, but in the all the camera and audio setup confusion, I forgot to put it in Full Auto (getting old), so this is really not a Full Auto Fun Video, it was still fun and I hope you enjoy it anyway. The other videos in this Full Auto Fun Series are for sure in Full Auto and I will be taking out the Barra 400e and give it another go in Full Auto this time so stay posted for the true Full Auto Fun Video for the Barra 400e shortly!
In this Field Test Shooting Video, I test out the Specna Arms Core SA-J73 AEG Airsoft Rifle in my Indoor Replica Airguns Sea Can Shotgun Range to see what the velocity/fps is and what the accuracy is like shooting .20 gram Airsoft BB’s through my Chronograph. I shoot in both semi and full auto at a paper target setup 30 feet down range. If you are more interested in information like details and specifications for the Specna Arms Core SA-J73 AEG Airsoft Rifle, then make sure to watch my Table Top Video I already made that also includes some nice close up video for you to check out…
First up I loaded up a mag of .20 gram Airsoft BB’s and proceeded to shoot 5 rounds through my Chronograph to get a baseline average. Specna Arms claims around 370-380 fps using the preinstalled internal spring setup. I averaged 382 fps with my slowest shot recording 379 fps and my fastest shot hitting 383 fps. All of them really close in terms of velocity and right on the mark of the claimed 370-380 fps using .20 gram Airsoft BB’s.
With the Velocity Test in the bag, I moved on to my Accuracy Test for the Specna Arms Core SA-J73 AEG Airsoft Rifle where I first shot 10 rounds in semi auto to see how tight of a grouping I could get, and then I also finished up the rest of the partially full magazine in full auto to see if that grouping opened up a bit with a lot more rounds and a bit of full auto rocking around. For my 10 shot semi auto grouping I did get around a 1 to 1.5 inch spread, and notably all 10 shots hit the bullseye with no sight adjustments out of the box. Unleashing the Specna Arms Core SA-J73 in full auto, the group did spread out just a little bit to around 3 inches or so, but again right on top of the bullseye for the most part. Very impressive results for sure!
Overall I am super impressed with the Specna Arms Core SA-J73 AEG Airsoft Rifle! At around $200 Canadian you get a well made decent quality AEG Airsoft Rifle that not only looks and feels really good, but performs as good if not better than some much more expensive AEG Airsoft Rifles out there. All you really need to get on top of this purchase would be a decent charger and battery setup along with some quality Airsoft BB’s and then you are ready to go. No need for any more upgrades at least not right away. So if you are looking for an affordable AK type AEG Airsoft Rifle with no real compromises to speak of, look no further than the Specna Arms Core SA-J73 AEG Airsoft Rifle. Not much else will be a better option in this price range.
In this Field test Shooting Video, I test out the Specna Arms Edge SA-X01 AEG Airsoft Rifle in my Indoor Replica Airguns Sea Can Shotgun Range to find out what the velocity is and what the accuracy is like shooting .20 gram Airsoft BB’s through my Chronograph. I also shoot in both semi and full auto at a paper target setup 30 feet away. If you are more interested in details and specifications for the Specna Arms Edge SA-X01 AEG Airsoft Rifle then make sure to watch my Table Top Video I have already made that also has some nice close up video for you to check out…
So first up I loaded up a mag full of .20 gram Airsoft BB’s and proceeded to shoot 5 rounds through my Chronograph. Specna Arms claims around 380 fps using the preinstalled spring setup, I averaged 348 with my slowest shot recording 344 fps and my fastest shot hitting 351 fps, so all of them pretty close in terms of velocity but a bit under the claimed 380 fps using .20 gram Airsoft BB’s
With the Velocity Test completed I moved on to my Accuracy Test for the Specna Arms Edge SA-X01 AEG Airsoft Rifle Field where I not only shot 10 rounds in semi auto to see how tight of a grouping I could get, I also finished up the 120 round magazine in full auto to see if that grouping opened up a bit with a lot more rounds and a bit of full auto shake. For my 10 shot grouping I did get around a 2 inch spread, I did notice the Specna Arms Edge SA-X01 AEG Airsoft Rifle shot really low and a bit to the right out of the box. I would say about 8 inches low and 3-4 inches to the right. There is some sight adjustment you can do so you should be able to dial in the sights to your personal preference. When I switched over to full auto which is always more enjoyable with AEG Airsoft Rifles, the grouping did open up a bit but not a lot more, maybe as much as 4 inches but I did put close to 100 rounds additionally into the target.
Overall I am impressed with the Specna Arms Edge SA-X01 AEG Airsoft Rifle, I would have liked to have seen it shoot a bit closer to the bullseye out of the box using the iron sights, but personally I would more than likely add a red dot sight anyway, and that will correct any sighting problems one may have with this Airlift Rifle. The FPS is I would say about perfect for most Airsoft shooting conditions and it can be used with the pre-installed spring either for CQB or out door games. I do like the 120 round magazines as there is no need to whined a spring half way through a magazine but you will need more magazines on hand or a good speed loader handy for an Airsoft Battle. Just keep in mind your battery options will be limited due to the battery area being rather small since this very compact AIrsoft Rifle does have limited space to put a battery.
Type: AEG Airsoft Rifles Manufacturer:Specna Arms. Model:Edge SA-X01 Materials: Mostly metal/aluminum. Weight: 5.52 pounds ( 2.50 kg). Total Length: 23.5-27 inches (597-686mm). Barrel: 10.63 inch (270) inner 6.03mm tight bore barrel non rifled. Propulsion: AEG. Action: Single action semi & full auto. Ammunition Type: .6mm plastic Airsoft BB’s. Ammunition Capacity: High cap 380 round magazines. FPS: 380 fps with installed spring, included M90 spring will be lower fps.
Trigger Pull: The trigger pull on the Specna Arms Edge SA-X01 AEG Airsoft Rifle is fairly shot and light, it is basically a simple off off switch as it is not mechanical but rather electric. For this reason there is no real creep or feel of a release. When you get to a point in the trigger you close a circuit that activates the electors motor cycling the spring.
Accuracy: At this time I have not made my Field Test Shooting Video or even shot the Specna Arms Edge SA-X01 AEG Airsoft Rifle, I am planning to make a video for this rifle next week if all goes well. I have reviewed other Specna Ames Core products in the past and made Field test Videos for them so perhaps check one of those videos out in the time being for a bit of a heads up of what you can expect from the Specna Arms Core SA-J73 AEG Airsoft Rifle.
Build Quality: Specna Arms Airsoft Rifles are made of good quality no matter if you go with the Core or Edge versions. You will still get a quality product with quality materials and metal parts where you need them. The Edge Series offers upgrades like more metal parts, improved gearboxes and electronics along with additional accessories but you pay a bit rmeo for the added quality and add ons.
Realism: The Specna Arms Edge SA-X01 AEG Airsoft Rifle is based on the AR15 or M16 platform of course in a very modern compact PDW styled. It looks and feels the part for sure with lots of working parts including the safety, selector switch, charging handle, dust cover, adjustable rear stock, pop-up front and rear sights as you would expect. Most of the hardware should be interchangeable with a real steel AR if you want to personalize the look of your Specna Arms Rifle.
Pros:
Very high quality product with quality components throughout (Already listed in Specifications).
4 positions rear stock.
ESA™ quick spring change system makes spring changes quick and easy.
Comes with two springs for potential indoor and outdoor usage.
Almost all metal build.
Removable fully adjustable pop-up sights.
No orange tips on our Canada Store versions.
Lots of rial mounting options using M-LOK System..
Comes with a fore grip and deans connector and two magazines.
Easy access to motor for any possible trouble shooting you any need to do.
I love the compact size. perfect for close closer quarters situations.
Cons:
Much higher cost than Core Series.
Magazine capacity is low but comes with two magazine.
You will need a very specific compact battery setup for this Specna Arms model.
Comments:
I for sure like the look of the Specna Arms Edge SA-X01 AEG Airsoft Rifle, but more than that you get a really great Compact PDW Airsoft Rifle at a reasonable price with a ton of quality components and a mostly all metal build. Specna Arms even includes an additional magazine in the box. You could go with one of their Core series of Airsoft Rifles in a similar PDW and save a bit of money but if you can afford the upgrade then I would go for this version as you will not need to upgrade it in the future and that alone will save you some money over time. I would suggest adding a couple Lipo batters and a good charger to your shopping cart and maybe even an couple more magazines.
My Vimeo Table Top Review for the Specna Arms Edge SA-X01 AEG Airsoft Rifle:
Type: AEG Airsoft Rifles Manufacturer:Specna Arms. Model:Core SA-J73 Materials: Fiberglass reenforced plastic and metal/aluminum. Weight: 5.7 pounds (2.59 kg). Total Length: 23.4 - 32.6 inches (594 - 828mm). Barrel: 15.7 inch (399mm) inner 6.03mm tight bore barrel non-rifled. Propulsion: AEG. Action: Single action semi & full auto. Ammunition Type: .6mm plastic Airsoft BB’s. Ammunition Capacity: High cap 430 round magazine. FPS: 370-380 fps with installed spring, included M90 spring will be lower fps.
Trigger Pull: The trigger pull on the Specna Arms Core SA-J73 AEG Airsoft Rifle is similar to a light single action trigger as essentially the trigger is non-mechanical, but rather it is more like an electrical on off switch. There is a little bit of take up with virtually no extra friction to let you know when the release is, with a bit of use you will figure out exactly when the trigger will release the action.
Accuracy: At this time I have not made my Field Test Shooting Video or even shot the Specna Arms Core SA-J73 AEG Airsoft Rifle, I am planning to make this video for next week if all goes well. I have reviewed other Specna Ames Core products in the past and made Field test Videos for them so perhaps check one of those videos out in the time being for a bit of a heads up of what you can expect from the Specna Arms Core SA-J73 AEG Airsoft Rifle.
Build Quality: One thing I can say, is no matter if you get the Core or Edge version of the Specna Arms AEG Air Rifles, you are getting extremely good value for your money, and neither one is going to have any low quality parts in it. Even the lower cost Core Series will have fiber glass reenforced plastic and metal parts along with a metal gearbox and virtually almost the same build as the more premium and higher priced Edge Series. You will get upgrades in the Edge Series like an aluminum receiver and buffer tube, a GATE X-ASR Mosfet, upgraded Gearboes, and an additional magazine.
Realism: The Specna Arms Core SA-J73 AEG Airsoft Rifle is based on the AK platform with a bit of a more modern look to it which includes a synthetic folding stock, a sight mounting system and a more modern magazine design. The Specna Arms Core SA-J73 AEG has lots of metal parts in it and has a good overall weight and feel to it which make is not too heavy or too light in my opinion. Our Canada version even come with a black flash hider rather than orange one which helps with realism.
Pros:
Very affordable price ($200 at time of video), yet very high quality product for what you pay.
Quality components throughout both the Core and Edge series.
Precision barrel internal 6.03mm diameter.
ESA™ quick spring change system makes spring changes quick and easy.
Comes with two springs for potential indoor and outdoor usage.
Plastic parts are fiberglass reenforced making them very durable.
Rear sight is adjustable on the fly for elevation.
No orange tips on our Canada Store versions.
Side mounting option for an optical or red dot sight system.
Metal V3 Gearboxes with metal gears and mostly all metal parts inside.
Decent amount of space for a battery.
Weight is about perfect, may actually too heavy with metal receiver?
Cons:
Plastic receiver.
Need to remove dust cover and use a screwdriver to adjust the hop-up.
No battery or charger included.
Comments:
The Specna Arms Core SA-J73 AEG Airsoft Rifle for right around $200 is not what I would expect for such a lower priced more entry level Airsoft Rifle. The build quality and components in this Airsoft Rifle are not budget by any means and when you hold it, it feels like a very high quality product. Sure you don’t get a battery or charger with it which you often find bundled with lower cost Airsoft Rifles, but generally these batteries and chargers are extremely entry level and will require upgrading almost immediately. So do yourself a favor and invest in a good battery setup if you do not already have one. If you’re in the market for an AK based AEG Airsoft Rifle and have a limited budget but still want a decent product, then I would recommend the Specna Arms Core SA-J73 AEG Airsoft Rifle for sure.
My Vimeo Table Top Review for the Specna Arms Core SA-C07-PDW AEG Airsoft Rifle:
Another box showed up at my door and this time I had no idea what was inside it, I asked the boys in the warehouse to surprise me and send some new product as I was low on review items, and in a couple of days later this tall somewhat large box showed up. In this Replica Airguns June Mystery Box Unboxing Video I open the box and take a look at what’s inside. I recommend you just watch the video and enjoy the suspense with me, but if you want to cheat and find out now, then look below at quick breakdown of each item…
This year at the KWA Booth I had the pleasure of running into John, and we went over a bunch of new items KWA had on display. John was even rocking a similar pair of Ray Ban Meta AI Glasses which made us look a little bit like twins…
In this KWA SHOT Show Interview John higgled the following products from KWA: The KWA ATP-Z and ATP-CT Optics Ready GBB AIrsoft Pistols which are convertible to SMG versions, along with a new prototype TAC-9 GBB Airsoft Rifle.
KWA AIrsoft products have always been one of favoriteAirsoft guns for their quality, looks and performance. They tend to offer a lot of Gas Blowback options which I really appreciate as a Replica AIrgun Collector.
It’s alwasy nice to have a chat with Bob at ASG, I have been interviewing him for years now and really missed not being at SHOT Show the last three years. As always, Bob really knows the ASG product line inside and out and took us through some of the new products and changes to the ASG lineup in 2024.
Some of the products include: The ASG CZ P-10 C CO2 Blowback Airsoft Pistol, the Steyr L9-A2 CO2/Gas Blowback Airsoft Pistol, the USW Gas Blowback Airsoft Pistol, the new Hybrid Airsoft line including the CO2 Blowback H-22 and the AEG H-15, the ICS Ape SE AEG Airsoft Rifle, and lastly the ICS Carnotaurus, Legacy, ACME High-Capa Pistol Series.
I am looking forward to get my hands-on many of these new ASG products and making reviews for everyone to checkout in the near future…
I’m pretty sure I have never made an Interview for Barra before in any of my past SHOT Show Videos, so I was really happy when I visited their booth and discovered a bunch of really great new products to talk about with GEO. Like many other Airgun companies, Barra does incorporate rebranded products from other manufacturer popular Airguns, but they also have some unique products I have never seen before. They are either working really closely with dedicated manufacturing companies or making these items in house. Either way it’s great to see new and interesting products.
Some of the products Geo went over with me in this SHOT Show 2024 Barra Interview where: The Barra CO2 1866 Lever Action Rifle, some Rifled Pellet Barrel Kits for the Schofield Revolver and 1866 Rifle, the 1858 CO2 BB Revolver, the 357 Shell Loading CO2 Revolver, the 400 AEG Airsoft Rifle and two new nameless Airguns they are still working on and perfecting, a full Blowback Competition Style BB/Airsoft Pistol and a compact AEG Airsoft Rifle.
It was great talking with the team over at the Barra Booth and I look forward to testing out their new items as they become available.
Kicking off my SHOT Show 2024 Interviews, I present my Umarex Interview with Mark Davis, you may remember Mark from past Umarex SHOT Show Interviews? This is a fairly long interview as Mark had a lot of product to show me including…
The new Marlin Lever Action BB Rifle, the Walther PDP CO2 BB Pistol, the BBX11 1911 Blowback CO2 BB Pistol, the MarkPoint Break Barrel .177 Caliber Pellet Pistol, the Trinity Hi-Cap 2011 Blowback Airsoft Pistol, the Gambler High Stakes Single Action Army CO2 Airsoft Revolver, the Glock 380 GBB Airsoft Pistol, the CQC Elite Force AEG Airsoft Rifle with i-Trace, and the Beretta PMX GBB Airsoft Rifle.
Yep, that’s a lot of products to go over in one Interview, and Mark did a great job! I am really looking forward to getting my hands on these new products from Umarex to review for everyone!
