Type: Blowback CO2 Airsoft Pistol. Manufacturer: Distributed by KJ Works. Model:M9A1 TBC. Materials: Mostly all Metal. Weight: 2.1 pounds (926 grams). Total Length: 9.25 inches (23.5cm) Barrel: 4 inches (10.2cm) metal non-rifled. Propulsion: CO2 x 1. Action: Semi auto blowback, SA & DA trigger. Ammunition Type: .6mm plastic Airsoft BB’s. Ammunition Capacity: 24 round drop out full size metal magazine. FPS: Claimed 360+.
Trigger Pull: The trigger pull on the KJWorks M9A1 TBC CO2 Blowback Airsoft Pistol is single and double action. When the hammer is back and it is in singe action, the trigger is short and light with about a quarter inch take-up before the release which is crisp and fairly light. You can decock the hammer and shoot in double action which does make the trigger pull much longer and a bit heavier but it is still very usable. There is also a semi cock-option where the hammer is partially cocked. This keeps the hammer off the firing pin and allows for a safer double action trigger pull.
Accuracy: So far I have not shot the KJWorks M9A1 TBC CO2 Blowback Airsoft Pistol or made my Field Test Shooting Video. I have shot lots of KJWorks Full Blowback Airsoft Pistols in the past and they have in general performed as expected. So I am confident when I get to the Field Test Shooting Video for the KJWorks M9A1 TBC CO2 Blowback Airsoft Pistol, it should perform well for me!
Build Quality: The KJWorks line of Airsoft Guns are known for their excellent build quality, the KJWorks M9A1 TBC CO2 Blowback Airsoft Pistol is another example of a well made Airsoft Pistol with lots of metal parts including the slide, frame, inner and outer barrel, magazine, trigger, safety, slide catch release, take down lever and magazine release. The only real plastic I can see is the grips, butt plate, and CO2 gas nozzle. Fit and finish is really good. There is just a little bit of slide wiggle, but all the mechanical parts work well.
Realism: Most Full Blowback Airsoft Pistols are built to be as close to a real steel pistol as possible with similar dimensions, weight and feel. The blowback action gives a Blowback Airsoft Pistol the required slide action to allow for chambering of an Airsoft BB along with the reseting of the hammer, so true single action shooting is possible. Other than shooting a real steel Beretta M9A1, the KJWorks M9A1 TBC CO2 Blowback Airsoft Pistol is as close as you can get to it. Holding this pistol in your hand, it would be hard to tell it is not the real deal.
Pros:
Pretty much all metal pistols with good weight to it.
Full heavy blowback operation.
Excellent fit and finish as always with KJWorks pistols.
High capacity full size drop out magazine that holds the Airsoft BB’s and CO2. (Can get Green Gas mags)
Comes with threaded outer barrel for adding a compensator or mock suppressor.
Comes with barrel extension for higher velocity shooting.
Easy to add accessories to under barrel picatinny rail.
White dot sights front and back.
Ambidextrous safeties.
Two toned tan and black finish looks good.
Field strip-able.
Cons:
Sight are non-adjustable.
Grips may be a bit wide for some small handed people.
Extended magazine makes it a bit bulkier.
You need an Allan key to adjust the Hop-up.
Comments:
The Beretta M9 is a classic Semi Auto Pistol that has been used in military and police for decades and has proven itself over time. I would say it is right up there with the classic 1911 as being recognized as a dependable and solid semi auto pistol. I still kind of prefer the 1911 but I’d take a Beretta M9A1 any day of the week. You really can’t go too wrong with the KJWorks M9A1 TBC CO2 Blowback Airsoft Pistol, it has it all… Almost all metal build, full blowback operation with both single and double action shooting options. You have a picatinny rail for adding accessories and easy to see white dot sights front and back. This is probably one of my favorite Beretta M9’s in terms of looks and features.
Type: Blowback CO2 Airsoft Pistol. Manufacturer: Distributed by KJ Works. Model:KP-19. Materials: Mostly all Metal. Weight: 1.9 pounds (850 grams). Total Length: 10.6 inches (270mm) Barrel: 4.25 inches (108mm) metal non-rifled. Propulsion: CO2 x 1. Action: Semi auto blowback, SAO trigger. Ammunition Type: .6mm plastic Airsoft BB’s. Ammunition Capacity: 25 round drop out full size metal magazine. FPS: Claimed 360+.
Trigger Pull: The trigger pull on the KJWorks KP-19 CO2 Blowback Airsoft Pistol is excellent, it is super short and light as you would expect from a 1911 trigger, the makeup is almost non-existent with a super light release. Out of the box I find it perfect but you have the option of adjusting it with the supplied Allen key since it has competition adjustably. Like I said, out of the box it felt perfect to me so there is no real need to mess around with it.
Accuracy: At this point I have not shot the KJWorks KP-19 CO2 Blowback Airsoft Pistol or made my Field Test Performance Video. I have shot my fair share of KJWorks Full Blowback Airsoft Pistols and they have in general performed very well for me, so I am confident when I get to the Field Test Shooting Video for the KJWorks KP-19 CO2 Blowback Airsoft Pistol it will do a great job!
Build Quality: The KJWorks line of Airsoft Guns is known for their excellent build and overall quality and the KJWorks KP-19 CO2 Blowback Airsoft Pistol is no exception. You will find all metal for the most part including some CNC Aluminum parts like the barrel and compensator, the slide and frame are metal along with the magazine and most of the controls. The pistol grip and trigger guard is all in one and the main plastic you will find on the KJWorks KP-19 CO2 Blowback Airsoft Pistol. Weight, feel and balance is really good.
Realism: The KJWorks KP-19 CO2 Blowback Airsoft Pistol is a double stack modern tactical 1911 in design. All of the controls and the overall design are that of a 1911 and so if you are use to shooting 1911’s, then you will be accustomed to this Airsoft Pistol. The full length blowback simulates the shooting experience along with some recoil feel and also allows for that true single action only trigger we are use to with 1911’s with its short and super light trigger pull. The KJWorks KP-19 CO2 Blowback Airsoft Pistol is fully field strippable which allows for easy to get to hop-up adjustments. I did notice that the Back-strap safety is non-functioning and just there for show, I am not sure why they did not make it a working safety?
Pros:
Lots of metal parts with good weight to it at nearly 2 pounds.
Full heavy blowback operation.
Excellent fit and finish as always with KJWorks pistols.
High capacity full-size drop out magazine that holds 25 rounds.
Picatinny rail underneath for adding accessories.
Adaptor plate for adding a red dot to the rear of the slide.
I like the green dot fiber optic sights, super easy to see on all backgrounds.
I like the two tone CNC aluminum barrel finish you can also see through the slide cutouts.
Super short and light skeletonized adjustable trigger looks and feels great.
Can use CO2 or gas magazines.
Field strip-able.
Cons:
Grips are wide, may not fit the hands of small shooters.
Not all controls are ambidextrous.
Rear sight is not adjustable.
Back-strap safety is non-functioning.
Comments:
I’ve mentioned in many of my videos how I really like 1911 styled pistols and of course ones with full blowback operation, so the KJWorks KP-19 CO2 Blowback Airsoft Pistol for me is a winner even before I even try it. Of course how it performs is going to be the real deciding factor, even if I am rooting for it. What is not to like though? It is almost all metal, has full blowback operation, easy to see fiver optic sights front and back, the ability to add a laser or tac light up front with a red dot on the back by installing the adaptor plate so you can really dress this one up and make it your own at the end of the day.
Type: Blowback CO2 Airsoft Pistol. Manufacturer: Distributed by KJ Works. Model:KP-13 TBC. Materials: Metal & Polymer. Weight: 1.7 pounds (770 grams). Total Length: 8.25 inches (210mm) Barrel: 3.7 inches (95mm) metal non-rifled. Propulsion: CO2 x 1. Action: Semi auto blowback, SAO trigger. Ammunition Type: .6mm plastic Airsoft BB’s. Ammunition Capacity: 22 round drop out full size metal magazine. FPS: Claimed 360+.
Trigger Pull: The trigger pull on the KJWorks KP-13 TBC CO2 Blowback Airsoft Pistol is what you would expect from a true Single Action Only Trigger, which is nice and light and relatively short. There is some initial take up but you can feel the point near the back where the release kicks in which is extremely light and predictable with no play in it. Of course you will have to rack the slide in order to place a round in the breach and fire the first shot, after that the blowback action will do all the slide cycling for you.
Accuracy: At this point I have not shot the KJWorks KP-13 TBC CO2 Blowback Airsoft Pistol or made my Field Test Performance Video. I have already made a full Field Test and Shooting Video of the non-TBC version which is virtually the same Airsoft Pistol but without the threaded outer barrel extension. You can watch that Filed Test Video here where I get around 350 average fps and close to a 2 inch grouping shooting at a paper target setup 30 feet down range. Stay posted for my Full Field Test Shooting Video for the TBC version down the road.
Build Quality: The KJWorks line of Airsoft Guns is know for overall good quality so I expect the KJWorks KP-13 TBC CO2 Blowback Airsoft Pistol to be just the same. From my testing with the non TBC version and my initial first impressions, everything looks really good, fit and finish are excellent and as expected you will find metal parts and polymer parts in all the same places you would find them in a real steel modern semi auto pistol.
Realism: The KJWorks KP-13 TBC CO2 Blowback Airsoft Pistol is not an exact replica of a specific semi auto pistol but you could say it looks a little bit like a Glock ;) You need to be careful when it comes to Glock as they do not like it when companies copy their guns and rightly so. There is enough differences with the KJ Works KP-13 TBC CO2 Blowback Airsoft Pistol so it should not set off any red flags over at Glock. It’s good that there are various color options, tan, grey and black. It does seem that only the Tan and Grey two tone versions are available in the TBC version while the black version we seem to have available in the all black non-TBC version.
Pros:
Metal and Polymer with decent weight and good feel to it.
Heavy Full blowback operation.
Excellent fit and finish as always with KJWorks pistols.
High capacity full size drop out magazine that holds the CO2 and 22 rounds.
Well hidden safety incorporated into the serial number under the barrel.
Working trigger safety.
Super easy to see in all conditions fiber optic sight up front.
All working components like the real steel Glock styled pistol.
Comes with extended threaded outer barrel for adding a possible compensator or mock-suppressor.
Comes with barrel extension for higher velocity shooting.
Would make a good training weapon if you are use to using Glocks
Comes in Tan and Grey two tone options also.
Can use CO2 or gas magazines.
Field strip-able.
Cons:
Sights are not adjustable.
Would have liked the addition of white dots or outline on the rear sight.
Slide spring could be slightly heavier.
Comments:
Let’s be clear, the KJWorks KP-13 TBC CO2 Blowback Airsoft Pistol is not a Glock Replica. It is different in many ways, the idea here is that it is close enough to be a good alternative if you are use to shooting Glocks and want something to train with that looks, feels and functions a lot like a traditional Glock. I am hoping the TBC version performs as well as the non-TBC version shot for me when I made my original Field Test Shooting Video back in 2023. For me the KJWorks KP-13 TBC CO2 Blowback Airsoft Pistol checks all the boxes… Full blowback operation, a very good trigger, lots of realism and I am sure good performance based on my past review.
Type:Airsoft GBB Rifle. Manufacturer: Novritsch. Model: SSQ22. Materials: Metal and plastic. Weight: 4 pounds (1.8 kg). Total Length: 32.7 inches (83cm). Barrel Length: 14.6 inches (37cm). Barrel: Metal non-rifled. Propulsion: Green gas. Action: Semi auto single action only trigger. Hop-up: Adjustable top mount hop-up. Ammunition Type: 6mm plastic Airsoft BB's. Ammunition Capacity: 36 round full size drop out plastic/metal magazine. FPS: 400+.
Trigger Pull: The Single Action Only trigger pull on the Novritsch SSQ22 GBB Airsoft Rifle is a lot like what you would find on a real steel Ruger 10/22. It is short and light in action making it light and quick enough for action shooting or sniping with accuracy from long range. You will have to work the bolt to load an Airsoft BB in to the breach and ready the single action trigger for the first shot, but then the blowback action will do that for you for the rest of the shots.
Accuracy: I have not shot the Novritsch SSQ22 GBB Airsoft Rifle or tested it out so far, so I don’t really have much to say in terms of accuracy or if it is close to the claimed 400+ fps, but I will be making a full dedicated Field Test Shooting Video for it a bit down the road when I get caught up with my Field Test Shooting Videos. So until then we will have to wait and see,
Build Quality: Novritsch is a new product line for me so I have not had much hands on with any of their guns so far. My first impressions are that they make very good quality Airsoft products using high quality materials with well thought out designs. The Novritsch SSQ22 GBB Airsoft Rifle is not super heavy even though it does incorporate a fair amount of metal components including CNC machined aluminum.
Realism: The Novritsch SSQ22 GBB Airsoft Rifle is not an exact copy or Replica of a Ruger 10/22 22LR Rifle but it does share a lot of its design and mechanical functions. Most people when they buy a base Ruger 10/22 generally do a lot of upgrading and modifications to them that ultimately make it look a lot more like the Novritsch SSQ22 GBB Airsoft Rifle at the end of the day. As it is Gas Blowback it functions very similar to the real steel version with working blowback action which does give a bit of recoil to it and allows for a very nice short and light single action trigger.
Pros:
Mostly all metal design.
Gas-efficient nozzle assembly, CNC machined Hop-Up chamber, and Maple Leaf 60° bucking with a large nub surface.
Easy to access and adjustable hop-up, up to 0.46g BBs out of the box.
Multiple M-LOK Mounting Options (Sides and bottom).
Three preinstalled QD Sling mounts on each side.
Front groove similar to gas pistol mags. You can see how many BBs are left in your magazine.
Skeletonized stock with a rubber pad that is attached to a Picatinny rail.
Nice GBB recoil with each shot.
Compact and light weight, easy to carry on the filed.
Ruger 10/22 owners will be use to this design.
Cons:
Does not come with any sights, will need to add one.
Only shoots in semi auto to conserve ammo.
Has preinstalled orange tip but can be removed.
Comments:
I am always a sucker for Gas Blowback Airguns in general and with Airsoft Rifles the vast majority tend to be AEG’s, so when I get the chance to review a GBB Airsoft rifle, I am always a bit excited to do so. The Novritsch SSQ22 GBB Airsoft Rifle has a lot going for it, there are lots of metal parts where you want them to be, a great single action trigger, mounting options for a red dot or optical sight along with M-LOK on the sides and bottom for whatever accessories you plan to add to it. It’s nice that it starts out pretty light as the addition of a scope, perhaps a foregrip, maybe a taclight and or laser will bring up the weight. I most certainly am looking forward to the Field Test Shooting Video so I can see how this one performs.
In this Field Test Shooting Video for the KJWorks MK1 Carbine Green Gas Airsoft Rifle, I checkout the velocity and power here in the Replica Airguns Indoor Airgun Shooting Range, to find out if the real world velocity is in the ballpark of the claimed 450+ fps velocity by KJWorks. I also shoot 10 rounds into a paper target from a distance of 30 feet to see how accurate of a grouping I can get. If you are interested in details, specifications and more close up video along with the Pro’s and Con’s for the KJWorks MK1 Carbine Green Gas Airsoft Rifle, then checkout my Table Top Video Review for it here.
Starting first with my velocity test, I loaded up the magazine with propane gas along with a full magazine of .20 gram Airsoft BB’s. The temperature was around 20 degrees Celsius or 68 degrees Fahrenheit, so not super warm or cold, in warmer conditions I would expect slightly higher fps from the KJWorks MK1 Carbine Green Gas Airsoft Rifle. KJWorks claims 450+ fps and my testing came pretty close to this with my five Chronograph readings hitting: 468, 451, 435, 436, 426 fps. Averaging 443 fps.
Next I made sure I still had 10 Airsoft rounds in the magazine and placed a fresh paper target 30 feet down range and shot all 10 rounds into the target using a semi rested shooting position, with my hands on a sand bag up front and sitting on a stool in the back. This allows me fairly stable shooting with less human factor. I did have to aim a few inches low on the center of the target as the KJWorks MK1 Carbine Green Gas Airsoft Rifle does shoot a bit high at 30 feet. 7 out of the 10 rounds hit all within about 2 inches of each other and then three rounds came out of the group increasing the 10 shot grouping from 2 inches to around 5 inches. I am wondering if perhaps I had some miss-formed Airsoft BB’s in the bunch as the shots that came out, really did come out a lot compared to the tighter 2 inch 7 shot main grouping.
Overall the KJWorks MK1 Carbine Green Gas Airsoft Rifle performed well, the velocity was right on the mark and was fairly consistent dropping off a bit as the Rifle cooled down from the gas. Accuracy was very good side to side but up and down I did notice more variation. The trigger is a double action only trigger so it is a bit longer and heavier than a real steel Ruger MK1 that is known for its beautiful short and light Single Action Trigger. Still the KJWorks MK1 Carbine Green Gas Airsoft Rifle performed well and I think with some good quality Airsoft BB’s, perhaps even a bit heavier than I used in this test, one could improve the accuracy at range and really be able to use this for some longer range outdoor Airsoft games. As it is a fairly light and short Rifle it would make for a super easy to pack around sniper rifle option.
In this months Replica Airguns Mystery Unboxing Preview Video, I take a look at 4 new items that showed up at my door. Two Airsoft Rifles, one being AEG and the other one a GBB. I also received two accessories for the GEM Alias super tiny multi ammo CO2 Pistol, A .50 caliber Paintball Barrel for it and and a 12 gram CO2 Adapter.
Both Airsoft Rifles are new to me from a company called Novritsch which is a higher end brand so the pricing is not cheap for either Airsoft Rifle. It was nice to get an AEG and GBB to review, the Novritsch SSR77 AEG Airsoft Rifle is a Replica of the Steyr AUG while the Novritsch SSQ22 GBB Airsoft Rifle is essentially a custom modded Ruger 10/22 copy, at least from what I can tell, it is solid and really well built.
I have already made a Table Top Video for the GEM Alias CO2 Pistol but I have been waiting for the .50 Caliber Paintball Barrel to show up so I can test out all 4 barrel ammo options. I also really wanted the 12 gram CO2 Adapter so I don’t have to use the small 8 gram CO2’s which are harder to find and not as cost effective as the 12 gram CO2. So now I am totally ready to make the GEM Field Test Shooting Review.
It’s been a while since I made a Field Test Shooting Video, probably well before I went to SHOT Show. I have been working on my SHOT Show 2025 Videos but those Interview Videos are all done and now it’s time to get caught up on some Field Test Shooting Video I have been wanting to make. So today I was able to make my Field Test Review Video for the Umarex DSX 45 Spring BB Pistol and for some this is a pretty entry level BB Pistol many might overlook but if you are simply looking for a 1911 based BB Pistol that is super inexpensive to buy, and cheap to shoot, and you don’t need quick semi auto shooting. Then the Umarex DSX 45 Spring BB Pistol Field Test Review could be an option for you. Make sure to watch my Table Top Review Video for the Umarex DSX 45 Spring BB Pistol for Details, Specifications, Pros and Cons and some nice close up video.
In this video I test out both the velocity and accuracy and I guess to some degree the usability so lets get started with the Velocity or fps portion of the testing. I loaded up the Umarex DSX 45 Spring BB Pistol with a half full hopper of 4.5 mm Steel BB’s, so around 100 BB’s which is way more than I needed and I shot 5 rounds through my Chronograph hitting the following fps: 191, 193, 188, 195, 197 which averaged 193 fps. Umarex claims a velocity of up to 240 fps which I think is a bit high as temperature is not even a factor with a spring piston Airgun, so warmer conditions will not really make much of a difference here.
I then placed a brand new paper target on my backstop 30 feet down range and proceeded to shoot 10 rounds into it using a semi rested shooting position. Hands rested on a sand bag up front and sitting on a stool in the back. This generally gives me pretty good stability while performing these tests, but there is always some human factor to take into consideration. I was not all that impressed with the grouping I got, the Umarex DSX 45 Spring BB Pistol likes to fling BB’s around a bit. You an see them curl so maybe some miscellaneous spin is being added in the barrel but it is not a consistent spin so the BB’s kind of spray all over the target that ended up giving me around a 8 inch grouping. Usually I can get around a 2 inch grouping with a BB Pistol that is generally what I would consider to be good accuracy.
I wish the Umarex DSX 45 Spring BB Pistol Field had hit closer to the 240 claimed fps and was also a bit more accurate as it would then be more usable at the 30 foot range I tested it at. I would suggest if you buy or own this BB Pistol, that you shoot it at targets closer in at 10-20 feet as the poor velocity and accuracy would be a lot less noticeable at these ranges and for that purpose it would be just fine. If you want a super low cost BB Pistol option that is also a decent looking 1911 Replica, and that you don’t need to go out and buy any CO2 to use it. Then take a look at one in our Replica Airguns Online Store. Heck, it’s only $19 US and $29 CAN right now!
This will be my final Interview Video for SHOT Show 2025. I did get to talk with someone from Crosman but the Daisy rep was not around totally with so I did my best to talk about a couple of the Daisy products that I felt were interesting. If you are not aware, Crosman and Daisy have now joined forces together along with Gamo, Benjamin and SPLATRBALL so all of these product were on display at the Crosman Daisy Booth. I focussed on the Crosman M1 Full Auto Carbine and their updated all black ST1 Full Auto BB Rifle. We then took a look at some of the Game Face Airsoft Products and then I performed my own Interview/Review for Daisy talking about the Woodland Trail Model 1911 and Model 25 Lever and Pump Action BB Rifles.
I had the pleasure of interviewing Mark from Umarex again at SHOT Show 2025 and Mark went over some of the new products from Umarex coming out this year. Make started of by showing me two new MOS (Modular Optic System) Gen 5 Glocks in a Glock 17 and Glock 19 versions. Both come with Umarex based red dot sights but you can change them up for something different if you choose to down the road. We then took a look at the new Umarex AER16 AR AEG Rifle in 4.5mm Steel BB rather than 6mm Airsoft similar to the Barra e400 that came out last year. In a nutshell it is a battery/spring operated 4.5mm Steel BB Full Auto AR Replica. Mark then showed us some A&L AK based AEG Airsoft Rifles they are now distributing that feature Full steel body construction with high-quality real laminated wood handguard and skeletal folding stocks. These are one to one in terms of size and weight adn very detailed. We then finished up the interview taking a look at the Legends Saddle Lever Action Shell Loading Rifle and the Umarex Smith & Wesson Competitor Shell Loading revolver.
Luckily I was able to find some time with James again this year and James gave us all the new details on some of the KWA updated and new products. Starting with the KWA ATP-Z Blowback Airsoft Training Pistol added recently to the KWA lineup, James also showed us a few versatile Carbine Pistol Kits made specifically for the ATP-Z and ATP-GT Pistols. Not yet fully released, James went over their updated TAC-9 hopefully coming out this year. We then got a nice tour of the updated Radian Model 1 AEG Airsoft Rifle with built in recoil system also built into KWA’s Q10 AEG Airsoft Rifle.
I spoke with Jacob from Barra and he went over a lot of new products adn updated products Barra is introducing this year. We discussed some new PCP Air Rifles with Canada import options, Jacob went over some new updates to their 1866 Muti-pump BB and Pellet Lever Action Rifle, and he went over Barra’s Gen 2 400e AEG BB rifle which include a higher capacity magazine, an increased velocity and unproved internal tolerances for smoother BB flow. Lastly Barra is introducing high grade 4.5mm BB’s that a re procession ground to be more uniform for improved accuracy and better BB feeding. Great for full auto guns.
It was nice to run into ASG (Action Sports Games) right away and talk with Bob for ASG. Bob always has a great understanding of the ASG product line and each year I Interview him and find out all the news and updated product in the ASG lineup. This year Bob’s goes over the new ASG CZ P-10 C CO2 Blowback BB Pistol, the Action Army C1 Pro Bolt Action CO2 Airsoft Rifle, ASG’s new Frag Impact Sound Grenades, along with some new additions to the Shadow 2 Series of Airsoft Pistols. Was a great start to this years SHOT Show 2025!
I’m back from SHOT Show 2025 Las Vegas and finished transferring and uploading all the video from all the cameras we shot it all on. We had a great time, we met a lot of great folks at the booths and it’s now time to put it all together and make some videos for everyone so I can share the experience!
I always like to put out a “Teaser Video” with some quick clips of the entire experience including some of the travels, a bit of the resort we stayed at, shots of Vegas and of course lots of the SHOT Show 2025 experience along with the booths we visited. Enjoy this quick preview and stay posted for my upcoming Interview Videos shortly…
In this Field Test Shooting Video Review of the KWC SP2022 NBB CO2 BB Pistol I set out the Velocity in FPS using a Chronograph along with the accuracy shooting 10 rounds at a paper target setup 30 feet away. Umarex claims just under 400 fps so the goal will be to see how close we can get to that power rating. I have already made a Table Top Review Video for the KWC SP2022 NBB CO2 BB Pistol where I go into details about specification and also show more close up video of this NBB CO2 BB Pistol. Make sure to watch that video if that is the information you are looking for as this video only goes into performance characteristics.
For my Velocity Test of the KWC SP2022 NBB CO2 BB Pistol, I shot 5 rounds through my Chronograph using a brand new CO2 in a typical room temperature environment, not too cold or too warm. I was able to get an average velocity of 355 fps with my slowest recored shot hitting 344 fps and my fastest recored shot hitting 362 fps. I did notice that the fps seemed to increase a bit with each shot which is not typical of CO2 Airguns. This may mean the CO2 was not fully pierced but I did crank it down pretty tight. Perhaps there is more potential power out of this CO2 pistol by using a slightly different brand CO2 than I was using, as sometimes a CO2 can just not fight properly, so by switching CO2 brands with a slightly different nozzle shape, you can get a better fit?
Moving on to my accuracy test, I setup a brand new paper target 30 feet away form my shooting position which uses a sand bag up front to rest the gun on and me sitting on a stool in the back to help stabilize each shot. There is also some human factor when performing accuracy shooting totes with any gun but I do my best to get the most out of each Airgun. The KWC SP2022 NBB CO2 BB Pistol shot very well centered on the target left to right and just a bit on the high side but not by much. The 10 shot grouping did spread out a bit to around 4 inches or so but it was an even spread. I would have liked to have seen just bit tighter grouping, even a 3 inch grouping means you are going to hit a pop can at 30 feet pretty consistently.
All in all the KWC SP2022 NBB CO2 BB Pistol is a fun plinker with enough power and accuracy at the end of the day to enjoy blasting targets in your back yard effectively. The double action trigger is pretty good, like most double action trigger it is a little longer but it is smooth and the trigger weigth is light to medium with a predictive breaking point at the end. I am a Sig Sauer fan so I do like the look and feel of this pistol an even though it is mostly plastic, the all metal magazine adds enough weight to make it feel more substantial in your hand than what you would expect form a mostly plastic Airgun. if you want a fun inexpensive plinker that is going to be efficient on CO2 and cost very little to shoot then the KWC SP2022 NBB CO2 BB Pistol would be a good choice.
To start things off with my Field Test Shooting Video of the Umarex Marlin Lever Action Spring BB Rifle, I shoot 5 rounds through my Chronograph to see what the real world velocity is in fps. Umarex claims around 300 fps. I was able to average right around 274 fps so not far off of the claim. My lowest performing shot was 270 fps with the fastest shot hitting 278 fps, so all very close in velocity which is typical of a spring piston Airgun, this will help with consistent accuracy especially in terms of elevation.
When it comes to the accuracy, the Umarex Marlin Lever Action Spring BB Rifle did as well or perhaps even better than my other testing using previous Red Ryder type Air Rifles. If I through out one flyer I got, my 10 shot grouping was able to get around a 2 inch grouping that was overall well centered on the target, maybe juts a hair to the right. Even with the flyer the grouping spread out to a 3 inch grouping. I am pretty sure I could do better as this was the first time shooting this rifle. Keep in mind as I have to work the lever action for each shot that requires me to hold the rifle straight up and down in order for proper BB loading, this means I need to fully reset my hands on the sand bag and re-aim for each shot which will effect accuracy consistency a bit. Still a good result.
All in all I do really like the Umarex Marlin Lever Action Spring BB Rifle, mainly as it has a longer shoulder pull more suitable for adults. I feel adults get left out a bit in terms of target marketing with the standard Red Ryder which is a very compact BB Rifle with a short shoulder pull more suited for kids and youth shooters. This makes the Umarex Marlin Lever Action Spring BB Rifle more comfortable to shoot as an adult but will still work for youth and kids as is is not too large in size or heavy or even very hard to work the lever action. Now the whole family can really take part in the fun experience of shooting a Red Ryder type BB Rifle!
Todays video is all about “damage”! How much damage can each of these .50 caliber ball options deliver to an object and the object of interest in todays video are a couple of over rip pumpkins that needed putting out of their misery. Luckily when I made this video the weather outside was cooperating with me and I go tI nice break in the rain. This was awesome as I was not looking forward to al the cleanup I would of had to of done if I performed this test inside the Replica Airgun Sea Can Shooting Range.
This is part three of my three part Indoor Filed Test Shooting Video for the Umarex T4E P2P HDP 50 Gen 2 CO2 Less Lethal Pistol. In this third video I test out the velocity and energy shooting 5 rounds through my Chronograph using the 8 gram All Steel Balls that I purchased on my own to test with this Less Lethal Pistol. I also shoot 5 rounds of the same All Steel Balls into a paper target setup 30 feet down range to get an idea on what to expect accuracy wise with the Umarex T4E P2P HDP 50 Gen 2 CO2 Less Lethal Pistol. I have already uploaded Field Test Shooting Videos one and two where I test out 1.6 gram All Rubber Balls and 2.7 gram Rubber/Steel Balls. If you have not watched my Table Top Video for the Umarex T4E P2P HDP 50 Gen 2 CO2 Less Lethal Pistol, then make sure to do so for closer up video and all the specifications and details.
Umarex claims a max velocity of 485 fps with an energy rating of 13 Joules with the Umarex T4E P2P HDP 50 Gen 2 CO2 Less Lethal Pistol when using their supplied ammo. I am assuming this would be using the Powder Balls as they are the lightest option of Ammo that are included in the box with this pistol and will have the highest velcoity. In my Chronograph testing I shot 5 rounds using the 8 gram All Steel balls. The velocity for the 8 gram All Steel Balls was much slower than the 1.6 gram All Rubber Balls and 2.7 gram Rubber/Steel Balls as expected, but they did stay fairly consistent ranging from a low of 132 fps to a high of 151 fps, averaging 138 fps. The overall energy rating ended up being the slowest by far out of all the rounds I tested in this Less Lethal Pistol, with an energy rating of only 7 Joules. Based on energy alone I would suggest using the All Rubber Balls as they achieved the highest energy rating at 15 Joules, even higher than claimed by Umarex.
Now that we understand that the 8 gram All Steel .50 Caliber All Steel Balls are not only the lowest velocity by a long shot, they also have the lowest energy rating again by a lot as compared to the other rounds tested. Maybe when I compare the accuracy during my target Test the .50 Caliber All Reel Rounds may redeem themselves. After Shooting 5 of the 8 Gram All Steel Rounds into my Paper Target from a distance of 30 feet, I did actually get the tightest grouping, even with a heavily fading CO2 that was near it’s end, so velocity did taper off making the shots shoot lower and lower with each shot. I did throw the final 5th shot out as I could literally see it loft to the target but even with the low CO2 and inconsistent velocity, I got my best grouping from the Umarex T4E P2P HDP 50 Gen 2 CO2 Less Lethal Pistol with a 3 inch grouping just slightly to the left of the bullseye but very close.
I was not surprised with the performance of the Umarex T4E P2P HDP 50 Gen 2 CO2 Less Lethal Pistol using the 8 gram All Steel Balls for this third Field Test. Velocity was much lower as expected than the other lighter rounds tested, but most surprising, the energy was around half of the All Rubber Balls. Perhaps the metal rounds just did not reach their maximum speed in such a short barrel due to them being a so much heavier weight? My conclusion on Ammo choice for the Umarex T4E P2P HDP 50 Gen 2 CO2 Less Lethal Pistol would be to go with either the All Rubber Balls or the Rubber Steel Balls. The All Rubber Balls by far had the highest velocity and energy rating but I did feel like the Rubber Steel Balls even though they where moving slower and had slightly less energy, seemed to hit the target with the most force based on the sound I was hearing while performing the testing. Either round will for sure make an intruder think twice about continuing their course of bad behavior. I will probably do some testing on how each of these rounds effects different targets in the future, I just need to figure out what I want to shoot at…
This is part two of my three part Indoor Filed Test Shooting Video for the Umarex T4E P2P HDP 50 Gen 2 CO2 Less Lethal Pistol. In this second video I test out the velocity and energy shooting 5 rounds through my Chronograph, using the 2.7 gram Rubber/Steel Balls that I purchased on my own to test with this Less Lethal Pistol. I also shoot 5 rounds into a paper target setup 30 feet down range to get an idea on what to expect accuracy wise with the Umarex T4E P2P HDP 50 Gen 2 CO2 Less Lethal Pistol. In video three I plan to test out the 8 gram all Steel Balls to see they are a viable option with a CO2 Pistol like this designed for much lighter rounds . If you have not watched my Table Top Video for the Umarex T4E P2P HDP 50 Gen 2 CO2 Less Lethal Pistol, then make sure to do so for closer up video and all the specifications and details.
Umarex claims a max velocity of 485 fps with an energy rating of 13 Joules with the Umarex T4E P2P HDP 50 Gen 2 CO2 Less Lethal Pistol when using their supplied ammo. I am assuming this would be using the Powder Balls as they seem to be a bit lighter than the Rubber Balls and will have the highest velcoity. In my Chronograph testing I shot 5 rounds using the 2.7 gram Rubber/Steel balls. The velocity for the 2.7 gram Rubber/Steel Balls was slower as expected but they did stay fairly consistent ranging from a low of 300 fps to a high of 309 fps averaging 304 fps. The overall energy rating ended up being 12 Joules, so obviously lower in fps than claimed by Umarex but close to the claimed 13 Joules. Still a good result close to the claimed raw energy.
The main point to this ammo comparison video is to finds out not only if the heavier 2.7 gram Rubber/Steel Balls will have around the same energy as the lighter 1.6 gram all Rubber Balls, but also to see if they have similar accuracy. In terms of accuracy the 2.7 gram Rubber/Steel Balls did just a little bit better than the 1.6 gram all Rubber Balls, not by a lot but, by about 1 inch with a 5 round grouping of 5 inches. All 5 shots were well entered shooting just a bit high of my aim point by about 3 inches but in general well centered left to right as a grouping.
I was happy with the performance of the Umarex T4E P2P HDP 50 Gen 2 CO2 Less Lethal Pistol using the 2.7 gram Rubber/Steel Balls for this second Field Test. Energy was very close to the claimed 13 Joules and the average 304 fps I got with this ammo felt snappy and got to the target quickly and sounded like they really hit hard. I do like the higher 15 Joules and 450 fps I got from the lighter 1.6 gram all Rubber Balls, so at this point I would probably recommend sticking with them for the most power and energy down range. Next up I test out the 8 gram all Steel Balls to find out if they are even an option or if they are simply juts to heavy for the Umarex T4E P2P HDP 50 Gen 2 CO2 Less Lethal Pistol.
This is part one of my three part Indoor Filed Test Shooting Video for the Umarex T4E P2P HDP 50 Gen 2 CO2 Less Lethal Pistol. In this first video I test out the velocity and energy shooting 5 rounds through my Chronograph, using the 1.6 gram included Rubber Balls that came with it and then I also shoot 5 rounds into a paper target setup 30 feet down range to get an idea on what to expect accuracy wise with the Umarex T4E P2P HDP 50 Gen 2 CO2 Less Lethal Pistol. In video two I will be testing out the 2.7 gram Rubber/Steel Balls in the same way, and then in video three I will be testing out the much heavier all steel 8 gram rounds to see if they are even usable in a CO2 Airgun designed for much lighter rounds. If you have not watched my Table Top Video for the Umarex T4E P2P HDP 50 Gen 2 CO2 Less Lethal Pistol, then make sure to do so for closer up video and all the specifications and details.
Umarex claims a max velocity of 485 fps with an energy rating of 13 Joules with the Umarex T4E P2P HDP 50 Gen 2 CO2 Less Lethal Pistol. In my Chronograph testing I shot 5 rounds using the 1.6 gram included all rubber balls. I did throwout the first shot as it was about 50 fps lower than the rest, perhaps as it was first out of the barrel which can happen. The other 4 rounds averaged 445 fps with an overall energy rating of 15 Joules, so a bit slow in fps than claimed by Umarex but a higher energy output. Perhaps the fps rating was for lighter rounds like the included 10 powder balls? Still an excellent result with more raw energy than expected which is great for a system designed to deter an intruder!
What good is power if you can not hit the target? That’s why I always test out accuracy as you want your gun to shoot where you point it. With Rubber Balls they tend to “wing” or “curl” a bit in the air which does spread out the groupings a bit over a BB or even Airsoft gun, so I was not expecting under a 2 inch grouping. My goal was to hit the target fairly centered with around a 6 inch grouping and the Umarex T4E P2P HDP 50 Gen 2 CO2 Less Lethal Pistol did exactly that for me, so mission accomplished. I also wanted to find out how many shots to expect from a fresh 12 gram CO2 and my results showed around 20 shots, so you can reload the internal magazine around 4 times before the trigger stops working, which is how you know the CO2 pressure is not adequate enough to shoot any more rounds.
I was very happy with the performance of the Umarex T4E P2P HDP 50 Gen 2 CO2 Less Lethal Pistol using the included 1.6 gram All Rubber Balls for this Field Test. Energy was even 2 Joules higher than claimed by Umarex, and I did not have a single malfunction with this pistol through my testing of all types of ammo I used in videos 1, 2 and 3. I would say the Umarex T4E P2P HDP 50 Gen 2 CO2 Less Lethal Pistol is your best option as a Less Lethal Pistol here in Canada. Will it stop a very determined intruder? Maybe not, but I would feel a little bit safer with the Umarex T4E P2P HDP 50 Gen 2 CO2 Less Lethal Pistol at my side than not having it at all. And a couple well aimed rounds to some soft tissue will for sure make someone reconsider some of their life choices. Stay posted for videos two and three coming out shortly…
This was a really fun Unboxing Video for me as I received something I feel a lot of Canadians might be really interested in protecting yourself in Canada is not a right especially if you use lethal force. So having a less lethal option is a really good idea.
Let’s get into what I found in this most recent Mystery Box in order of appearance…
The first item I unboxed was the KWC SP2022 CO2 NBB 4.5mm Steel BB Pistol. A pretty basic 4.5mm CO2 BB Pistol mostly made out of plastic but with a full size 21 round drop out metal magazine that does help a lot to add some much needed weight to this Airgun. It uses standard 12 gram CO2 with a claimed velocity of 450 fps.
Probably the most exciting item I pulled out of this months Mystery Box was the Gen2 Umarex P2P HDP 50 Rubber Ball purpose built Less-lethal solution for personal and family protection. Most of the similar Rubber ball Less-lethal Airguns I have tested generally do not pack enough punch to really be much of a deterrent in my opinion but the Gen2 Umarex P2P HDP 50 has a claimed 495 fps and when I tested it out after making this video it defiantly has some power. I would not want to be at the receiving end of this product especially in close proximity. The Gen2 Umarex P2P HDP 50 uses a traditional 12 gram CO2 and holds 6 rounds of rubber ball or powder ball, it does come with 10 of each to get you started.
Next I took a look at three KJWORKS Airsoft Pistols all of which came with CO2 Magazines, extension barrels and thread on tips. The KJWORKS KP-19, the KJWORKS M9A1 TBC, and the KJWORKS KP-13 TBC. As expected with KJWORKS Airsoft Guns, they looked really good and will be a joy to review and test out.
Last out of the Mystery Box was a new product from Umarex, a full sized Marlin Cowboy Lever Action BB Rifle in the style of the classic Red Ryder BB Gun but as mentioned in a larger size more suitable for an adult. Hey why do the kids get to have all the fun? The Umarex Marlin BB Rifle holds 650 rounds in its BB hopper and has a claimed fps pf 300. It also has an adjustable for elevation peep sight in the back with a metal lever and a Classic Faux Wood Finish.
