Trigger Pull: The trigger pull on the Umarex Beretta APX CO2 Blowback BB Pistol is a little different then that of the real steel APX. On the real steel APX there is actually a trigger safety and the actual gun uses a striker based system with a fairly short reset and take-up. On the replica Airgun version the trigger does not have a built in safety and the reset and take-up are much longer (full length). I have read that both the real steal and BB versions of the APX both have about 6 pounds trigger pulls but I personally felt like the Airgun version was heavier than that, perhaps because of the long pull. Overall the Umarex Beretta APX CO2 Blowback BB Pistol trigger is acceptable but not my favorite.
Accuracy: I have not shot the Umarex Beretta APX CO2 Blowback BB Pistol so far but based on similar blowback stick magazine BB air pistols from Umarex with around 400 fps performance, I know that it will have a medium blowback feel and should shoot pretty close to the claimed 395 fps. I also expect at least a 2 inch or smaller 10 shot grouping from 30 feet back.
Build Quality: Very good, the Umarex Beretta APX CO2 Blowback BB Pistol feels heavier than 1.5 pounds in the hand, perhaps because it is a more compact gun. The metal slide, metal stick mag and internal metal parts all help to balance off the polymer frame nicely. Fit and finish is also good.
Realism: The Umarex Beretta APX CO2 Blowback BB Pistol overall is a really close replica to the real steel APX other than the added safety and missing trigger safety. The added safety does not stand out too much and does serve a purpose while the missing trigger safety could of at least been there for show if not an actual working safety. Other than that the Umarex Beretta APX CO2 Blowback BB Pistol is very close to the Beretta APX with its full licensing, open ejection port, recessed barrel working slide catch release and blowback operation. Available at the:Replica Airguns Store
Pros:
Great weight and feel to it, build quality seems really good.
Really nice replica of the original Beretta APX in most ways.
Working slide catch and release.
Fully Beretta licensed.
Easy to see white dot sights front and back.
Recessed barrel and open ejection port for added realism.
Accessory rail for adding a laser or tactical light.
Stick magazine but plate gives the elusion of a full size magazine and covers the CO2 tab.
Warning instruction are nice and discreet!
Cons:
Trigger is a bit long and perhaps heavier than the real steel APX trigger. It also does not have the trigger safety.
Has a stick magazine rather than a full size magazine.
Sights are non-adjustable which is common with airguns like this one.
Comments:
It's always nice to get another airgun replica for fans of that particular real steel gun so they have a low cost shooting option they can use in a lot more locations for some safe trigger time. The Umarex Beretta APX CO2 Blowback BB Pistol is a great addition for sure and it's also nice that it is somewhat Glock like in looks and operation for those Glock fans out there that are having a tuff time locating a Glock airgun replica :) Other than my trigger beef, I really like the Umarex Beretta APX CO2 Blowback BB Pistol. I hope it performs as good as it looks when I do my field test shooting video in a bit.
My Vimeo Videos for the Umarex Beretta APX CO2 Blowback BB Pistol:
Type: Air Rifle / Machine Gun. Distributer: Umarex Model: Legends MP 40. Materials: Mostly Metal build. Weight: 7.7 pounds (3.5 kilograms) Barrel: 10 inches - smooth bore steel. Propulsion: 2x12 gram CO2. Action: Internal BoltBlowback single action. Ammunition Type: 4.5mm Steel BB's. Ammunition Capacity: 52 round full size drop out magazine. Max FPS: 465.
Trigger Pull: The trigger pull on the Umarex Legends MP 40 Blowback CO2 BB Machine Gun is single action only and even though I have seen it tested at around 10 pounds pull, in person it does not feel that heavy and is actually fairly smooth. You will need ti charge the bolt for the first shot just like you would on the real steel MP 40.
Accuracy: I have not done my official Field Test Shooting Video for the Umarex Legends MP 40 Blowback CO2 BB Machine Gun but did take it outside for a quick test run. Like others have reported back you really need to take your time loading the double stack magazine properly or you can have some feeding issues. it may even be a good idea to use a little lubricant in the magazine to help with BB smoothness. I will know more after I ahed played around with the Umarex Legends MP 40 Blowback CO2 BB Machine Gun a little more and worked out the BB feeding issues.
Build Quality: The Umarex Legends MP 40 Blowback CO2 BB Machine Gun is pretty much all metal other than the stock and pistol grip. Pretty much everything that is black is going to be metal on this airgun. It weighs in at a hefty 7.7 pounds which is only a punt off form the real steel version. Overall the fit and finish is really good, all mechanical parts including the retractible stock work flawless.
Realism: The Umarex Legends MP 40 Blowback CO2 BB Machine Gun is a 1 to 1 replica of the real steel German made World War II Machine Gun. It is very authentic looking and has very similar operation. The BB version does have the ability to shoot in semi auto mode which the real steel version did not but this is a good feature for saving on CO2 and BB's It would have been nice if the bolt was abel to lock all the way back and up but since the movement is shortened this is not possible. Still the Umarex Legends MP 40 Blowback CO2 BB Machine Gun is a really nice replica and almost every way.
Great to have another full size Rifle / Machine Gun available to purchase in a BB gun version.
Mostly all metal design with good overall weight.
Semi and Full auto select-ability.
Dual CO2 design for increased shots and less cool down effect.
High capacity full size drop out metal magazine.
Great looking replica of the real steel MP 40 in looks, operation and weight.
Internal bolt blowback will give a bit of recoil feedback feel.
Adjustable rear sight for shooting at different ranges.
Price point is reasonable for this type of full size mostly metal rifle.
Cons:
Sights are not adjustable for windage.
Bolt does not go all the way back to the lockout position.
Some reviewers have said that a full mag load does not always work well in full auto mode.
Comments: When I first got my hand on the Umarex Legends MP 40 Blowback CO2 BB Machine Gun at this years SHOT Show I immediately knew it was going to be a hit. The Umarex Legends MP has a lot going for it... High fps, semi and full auto, nostalgia of being a war replica and super great build quality and fit and finish. The questions is really who wouldn't want one? Especially being a replica BB rifle which has to be one of the more limited areas when it comes to airgun replicas. I look forward to shooting this offering from Umarex a little more and sharing my experiences with everyone.
My Vimeo Table Top Review of the Umarex Legends MP 40 Blowback CO2 BB Machine Gun:
What's not to love about the Umarex Legends MP 40 CO2 Blowback 4.5mm Steel BB Full Auto Machine Gun? It's pretty much all metal weighing in at close to 8 pounds, The Legends MP has a max fps of up to 465, shoots in both semi and full auto and has a high capacity all metal 52 round magazine that holds not only 1 CO2 but 2 CO2 for close to 200 rounds of semi auto shooting or about 140 shots in full auto. I really look forward to my Field Test Shooting Review of the Umarex Legends MP 40!
Not to be out shadowed or forgotten in the preview video, I also show off another 2017 SHOT Show CO2 Blowback Air Pistol, the Umarex Beretta APX! Right away the Umarex Beretta APX feels nice and solid in the hand weighing in at around 1.5 pounds with a heavy metal slide and really high quality plastic or polymer frame. You will find some nice details like a cut out ejection port and recessed barrel and of course full Beretta licensing from Umarex. The Umarex Beretta APX CO2 Blowback BB Pistol has a pretty decent claimed fps of close to 400 and a 20 round stick magazine that when inserted has that full size magazine look to it.
You'll also find other nice details like white dot sights front and back and a working slide catch release. My only gripe with the Beretta APX is the trigger, it does not ahed the trigger safety you would find on the real steel Beretta APX and the action is very long and perhaps a bit heavy. Other than that the Umarex Beretta APX looks to be a really nice replica airgun.
Type: Nerf Gun. Manufacturer: Nerf Hasbro Model:Rival Zeus MXV-1200. Materials: Mostly plastic build. Weight: About 3 pounds with batteries installed. Ages: 14+ (My son is 10 and he is more than OK with this gun!) Propulsion: Electric flywheel 6x C batteries. Action: Semi auto. Ammunition Type: Nerf High-impact round balls. Ammunition Capacity: 12 round tube magazine. Max FPS: 100.
Trigger Pull: The trigger on the Nerf Rival Zeus MXV-1200 is a little long and requires a firm trigger finger but it is not overly heavy. When you press the trigger it allows a Nerf High-impact round ball to advance into the motorized spinning flywheel area where the ball is accelerated and shot out of the inline barrel .
Accuracy: Keep in mind the Nerf Rival Zeus MXV-1200 is designed as a fun in home battle gun so long range accuracy is not really that important. At up to 30 feet or so you shoudl have no problem hitting a person sized target. The Nerf High-impact round balls do come out the the barrel with a fair amount of spin so some random hooking can happen, usually the spin is more of a backspin that helps keep the ammo targeting in a more linear trajectory.
Build Quality: The Nerf Rival Zeus MXV-1200 like most Nerf guns is built to take a fair bit of a beating since the target audience has mainly been kids and we know they are rarely careful with anything ;) The Nerf Rival Zeus MXV-1200 is mainly plastic but as I mentioned it is high quality and so far has held up well to usage. Fit is good with all interchangeable parts working well and the finish has stayed pretty much pristine!
Realism: Nerf guns are not made to be too realistic since they are meant to be toys and not look too closely like a real gun, hence the brightly colored plastic and more futuristic design. I do like the addition of Picatinny styled rails in several locations where one can add accessories like magazine clips, red dots or even a tactical light or laser sight.
Pros:
Not as extreme as a Paintball gun but a little more intense than a standard Nerf gun.
Good build quality overall.
Easy to quickly swap out a fresh 12 rode tube magazine.
Flip up sights
Picatinny raise for adding accessories.
Decent power and accuracy for a Nerf style gun.
Semit auto action for fast follow up shots.
Cons:
Will use up batteries pretty quickly.
Flywheel will slow down when shooting close together semi auto shots.
Loading magazines does take some getting use to.
Comments: The Nerf Rival Zeus MXV-1200 is a great option for pretty much anyone looking for a fun battle gun you can use indoors in your home with no worries about breaking windows or messing up your house. not to mention leaving west all over your body! The Nerf Rival Zeus MXV-1200 is going to be a bit more extreme than a standard Nerf gun for sure but way more toned down compares to a paintball gun or even an airsoft gun so if you want some good old rainy day indoor fun then checkout the Nerf Rival line of Nerf guns.
My Vimeo Table Top Full Review for the Nerf Rival Zeus MXV-1200:
I had a chance to take out my Swiss Arms SA 92 Stainless Version and Swiss Arms SA 1911 Tactical Rail System CO2 Blowback BB Pistols and see how they performed in the Sea Can Airgun Shooting range and they did pretty good, I have treated very similar KWC version of these guns in previous videos and for the most part the Swiss Arms Stainless Versions are just a little prettier cosmetically. I didn't test out the Swiss Arms SA 1911 Seventies Stainless Pistol since I expect it would have performed the same as the other 1911 in this Field Test Shooting Video.
So how did they do? First off I fired five rounds through my now almost perfectly working Chrony Chronograph and the SA 92 ended up shotgun a little faster with an average of right around 320 fps while the Swiss Arms SA 1911 Tactical shot an average of 302 fps. I was using brand new Sig Sauer CO2 and RWS Match Grade Precision Steel 4.5mm BB's for the entire review.
Moving on to the accuracy, I setup in my rested position which is about 30 feet back for the paper target. I was sitting and using a sand bag to rest the pistols on for stability. This gives me a very stable shooting position but there is still a little human factor involved since the guns are not locked in place. Both CO2 Blowback BB Pistols shot about a 2 inch 10 round grouping but the Swiss Arms SA 1911 had better shot placement pretty much hitting exactly where I aimed it, the Swiss Arms SA 92 Stainless on the other hand wanted to shot rather low, I had to place my aim at the top of the rings to get the SA 92 to hit near the bullseye. It did shoot really well left to right, unfortunately the Swiss Arms SA 92 Stainless does not seem to have a hop-up adjustment so you may have to adjust your aim point higher than normal with this one.
Both guns had great single action triggers with heavy blowback operation, I did find the Swiss Arms SA 1911 Stainless Tactical had a bit of a sticky slide when I first shot it but after a few shots it smoothed out. If you're looking for a KWA / Cybergun 1911 or Taurus PT 92 Blowback Airgun and want it ti have a little more curb appeal then make sure to checkout the Swiss Arms Stainless series of CO2 Blowback BB Pistols.
I know this video is going to excite many of you if you already like the basic KWC 1911 and PT92, also known as the Tanfoglio Witness, GSG 92 and many other almost exactly the same guns from Swiss Arms, Gletcher, Cybergun and even Umarex and Crosman.
There are tons of these KWC CO2 Blowback BB Pistols and Airsoft Pistols on the market in various versions with all kinds of different licensing on them and I have seen lots of custom modification photos from my viewers showing me how thy have striped and polished their KWC blowback Air Pistols and even added real wood grips.
That's why I think it's super cool that now you can get your already blinged out and polished Cybergun/KWC 1911 or PT92 and realy for not a lot more money at the end of the day! The real problems is availability since these stainless versions are in high demand.
So what are we looking at in this video? I have two Cybergun/KWC 1911's one is a basic 1911 A1 with a parkerized and stainless frame and slide, you also have a real wood look grip (Looks like wood but is not actually wood...) The basic Swiss Arms 1911 has been called the SA 1911 Seventies Stainless Pistol while the more tactical Swiss Arms SA 1911 is rightfully called the SA 1911 Tactical Rail System since it has a lot more tactical features like a rail, ambidextrous safety, white dot sights, and tactical trigger and hammer.
The Swiss Arms SA 92 Stainless which is essentially very similar to the GSG 92 or KWC PT92 again offers a parkerized and stainless frame and slide with the simulated wood grips.
Make sure to watch my update video for these three very attractive Swiss Arms CO2 Blowback BB Pistols from Cybergun/KWC and if you're interested in purchasing one you like then see if we have them in stock in our Canada Replica Airguns Store.
Type: Air Pistol. Manufacturer: Sig Sauer ASP Model:Sig Sauer ASP P320. Materials: Metal and plastic build. Weight: 1.81 pounds (821 Grams). Barrel: 4.75 inches - Rifled steel. Propulsion: 12 gram CO2. Action: Blowback single and double action. Ammunition Type: .177 caliber pellets and 4.5mm Steel BB's. Ammunition Capacity: 30 round belt fed stick magazine. Max FPS: 430.
Trigger Pull: The trigger pull on the Sig Sauer ASP P320 CO2 Blowback .177 Caliber Pellet Pistol is a lot better than I thought it was going to be considering each time you pull the trigger it has to advance the 30 round belt fed magazine and cock the internal hammer since it is double action only. The blowback operation is really only for show and feel since it does not cock the hammer for a more single action type trigger pull. You can expect a fairly long trigger pull because it is double action only but overall it is not too heavy.
Accuracy: I have not done my official Field Test Shooting Video for the Sig Sauer ASP P320 CO2 Blowback .177 Caliber Pellet Pistol but hope to have it done shortly. Since I also haven't really done an official shooting test for the Sig Sauer P350 and P226, I figure I will test out all three of them at the same time.
Build Quality: The Sig Sauer ASP P320 CO2 Blowback .177 Caliber Pellet Pistol is a bit heavier (closer to 2 pounds) than the P250 which hits the scale at only 1.5 pounds , this does make the Sig Sauer P320 feel a bit more solid in the hand. The Sig Sauer P320 has a metal slide and polymer frames similar to the real steel version which gives it authentic weight, balance and handling. Sig claims that their entire APS line of pellet guns is life tested for 15,000 shots so you know this gun is going to last and provide years of shooting fun. The fit and finish seem really good, so far no real paint or finish problems and all mechanically everything is operating as it should.
Realism: The Sig Sauer ASP P320 CO2 Blowback .177 Caliber Pellet Pistol is a very close replica of the real steel Sig Sauer P320. The hammer, slide catch release and take down leaver are purely for show with the hammer being moulded into the slide and frame. One slight disappointment for me is when a gun does not have a cut out ejection port, that is also the case with the otters ASP Sig Sauer airguns like the P226 and P250 but it does not take away from the shooting fun in any way.
Good overall replica of the real steel Sig Sauer P320.
Designed by Sig Sauer and made in Japan, fully Sig Sauer licensed.
Should have nice heavy blowback operation like the ASP P250 and P226.
Has better weight than the P250, almost half a pound heavier.
White dot sights for easy target acquisition and accessory rail for add ons.
Super high capacity 30 round belt feed magazine.
Decent feel to the trigger not heavy or as sticky as I thought it might be having a 30 round belt fed magazine.
Cons:
Hammer is moulded into the slide and frame, does not function at all.
Sight are non adjustable.
Ejection port is not cut out and there is no working slide catch.
Comments: I was happy when Sig Sauer released their ASP Sig P250 and P226 CO2 Blowback Pellet Pistols with their 16 round double sided stick magazines like we have seen in several otters CO2 Pellet Pistols. But I love the introduction of the 30 round belt fed magazine. I am hoping the belt fed magazine performs while actually shooting pellets as good as it feels when dry firing it, I guess we will have to wait and see when I do my Field Test Shooting Video :) Overall the new Sig Sauer ASP P320 Pellet Pistol looks to be an upgrade of sure to the P250 in terms of improved weight and a higher capacity magazine.
My Vimeo Table Top Review of the Sig Sauer ASP P320 CO2 Blowback .177 Caliber Pellet Pistol:
Another 4.5mm Steel BB Field Test Shooting Review from the new Sea Can Airgun Shipping Container Shooting Range. Yes it's a Crosman but it's really made by KWC and is based on the KWC Beretta / Taurus M92. Depending on which version you get, it came in either semi auto only or semi auto and full auto selectable. The Crosman version does shoot right out of the box in both semi and full auto which is nice.
On to my performance results with the Crosman PFAM98 Taurus PT-92 CO2 Blowback BB Pistol. My feet per second velocity results using a brand new CO2 in a 22-23 celcius environment where right up around 333 fps from a 5 shot string. This is about what we are use to from KWC full blowback CO2 BB Pistols.
Moving on to accuracy, I shot 10 rounds at my paper target which is setup about 30 feet away. I was also using a rested seated shooting position with my hands and gun resting on a sandbag upfront. I did have to reset this test as one of my cameras did not cooperate the first time around and this may have effected the accuracy juts a bit as velocity spread can make the BB's spread out a bit especially high and low on target. I did get a nice 5 shot group that was in a tight under one inch group but some of the other 4.5mm Steel BB's did shot higher and lower leaving the tighter grouping.
When I put the Crosman PFAM98 Taurus PT-92 CO2 Blowback BB Pistol in full auto mode and released the last 10 or so BB's they of course sprayed the target randomly. This was expected with the heavy blowback and fast shooting.
Another Airgun Shipping Container (Sea Can) Shooting video and for this indoor filed test I put the KWC - Cybergun M45A1 1911 CO2 Blowback Airsoft Pistol through its paces.
What I am super happy about is that my Chrony Chronograph seems to be working really well as I tested a pellet, steel BB and Airsoft pistol out today and every single round through my Chrony got a reading :)
Now back to the Field Test Shooting Review at hand... I started off by placing 5 shots through my Chrony Chronograph using a brand new CO2 with .20 gram Airsoft BB's and got a really consistent reading for all 5 shots with an average of 357. The lowest shot was 353 and the fastest shot was 364 so all shots where really close in velocity. The container temperature was a near perfect shooting temperature of 23 degrees Celsius which was ideal for optimal CO2 velocity testing.
During my accuracy portion of this Field Shooting Test. I used my new seated in the back and sand bag rested up front shooting position which is about 30 feet back from my paper target. I did notice during my Chrony testing that the Cybergun KWC Colt 1911 Rail Gun M45 A1 CO2 Blowback BB Pistol liked to shoot a bit high, perhaps the hop-up needs a bit of twerking? So for my accuracy testing I shot at the bottom ring of the target, this helped me get more shots on the paper for sure but the Airsoft BB's still moved around a bit vertically. I was able to get about a 4-5 inch 10 shot grouping which is totally acceptable for a close range Airsoft sidearm and in an Airsoft battle I would think even shooting at about 50 feet or so I could easily hit a persons mid section consistently.
The Cybergun KWC Colt 1911 Rail Gun M45 A1 CO2 Blowback BB Pistol has a ton of blowback kick to it and a super nice single action trigger like all the KWC 1911's The modern Tactical coloration and trimmings makes this pistol a great choice as a present day side arm. It's real looker for sure with performance to match!
Well the Shipping Container Office and Airgun Shooting Range is finally all ready to use and so for this first ever airguns shooting video in it, I simply wanted to try out a couple of airguns and see how this new setup worked. I also wanted to play around with some camera position setup to see how it all looked and if there will be any additional lighting or placement considerations.
Summer is here! While some folks are working on a tan, you're out working on your aim. This weekend, stock up on all the essentials — ammo, CO2, targets, extra mags — so you can shoot until the sun goes down.
When you spend $50 or more on any items, we'll ship them to you for free! Ends Monday, so don't wait.
Type: Blowback Airsoft Pistol. Manufacturer: KWC - Distributed by Cybergun. Model: Colt 1911 M45A1. Materials: Almost all metal. Weight: 2 pounds (907 grams). Barrel: Metal non-rifled. Propulsion: CO2 x 1. Action: Semi auto blowback, single action only. Ammunition Type: 6mm plastic Airsoft BB's. Ammunition Capacity: 17 round full size metal magazine. FPS: 340+ using .20 gram BB's.
Trigger Pull: The trigger pull on the Cybergun KWC Colt 1911 M45A1 CO2 Blowback Airsoft Pistol is what you would expect from a true single action 1911 styled pistol and typical to all the other KWC 1911's on the market. It has a short take up and then a nice light and crisp release. The working grip safety is a nice touch requiring your palm to be pressed against it for the trigger and hammer to operate..
Accuracy: At this point I have not shot the Cybergun KWC Colt 1911 M45A1 CO2 Blowback Airsoft Pistol, I imagine it should perform well considering it has adjustable spin-up or hop-up. According to the manufacturers claimed fps, we should get somewhere in the mid to high 300 fps range using .20 gram Plastic Airsoft BB's. I'll add this one to the list of airguns I need to field test review!
Build Quality: Most KWC built full blowback airguns are built pretty well with an almost all metal build and good overall fit but sometimes the finish can wear off a bit especially in the high points. The Cybergun KWC Colt 1911 M45A1 CO2 Blowback Airsoft Pistol seems to have a bit heavier finish on it. I looks really good and seems to be holding up well.
Realism: The Cybergun KWC Colt 1911 M45A1 CO2 Blowback Airsoft Pistol is a close replica of the real steel Colt 1911 M45A1 in almost every way other than the fact that it shoot s6mm airsoft BB's rather than 45 auto bullets :) The only real notable cosmetic difference I saw was the rail having less notches in it. Other than that it is bang on including the layered grips. Available From: The Replica Airguns Store.
Pros:
All metal construction - Good weight and solid feeling gun.
Nice heavy blowback action.
Very Accurate 1911 M45A1 styled replica.
True 1911 Single action trigger, excellent pull, very smooth and light.
Accurate trigger design and working grip safety.
Lots of tactical upgrades on this version (Tac style trigger and hammer, textured grips, ambidextrous safety, white dot sights, Rail for accessories)
Love the desert tan color and layered grips.
Cons:
Sacrifice fps and shots per CO2 because of the heavy blowback but worth it.
Finish on the Cybergun and KWC guns can were off on the high points a bit but some people like the look.
Comes with the orange tip (I took mine off).
Comments:
I have always been a big fan of the KWC line of full blowback airguns and this one is no exception. It's kind of interesting that KWC does not seem to make there own blinded out versions of these guns and that a company like Cybergun is distributing them? They do look really great and this entire line with all the variations and new models will for sure keep selling these airguns. And they don't just come in Airsoft versions, I will also be taking a look at some similar 4.5mm Steel BB KWC made airguns shortly!
My Vimeo Video Review for the Cybergun KWC Colt 1911 M45A1 CO2 Blowback Airsoft Pistol:
I got a lot done this week in the Shipping Container Project Office and Airgun Shooting Range. Finished up all the drywall office mudding, I primed and painted the the office, connected up all the electrical and office lighting and installed the hardwood and baseboard along with the trimming. All that's left in the office is some caulking, paint touchup and then I have to figure out how I'm going to finish up the shooting hole? I do have some ideas for it though...
Next week I will be working on these odds and ends and hopefully may even get the shooting range spray foam insulted?
About three weeks ago I started the interior construction of the Shipping Container Project. So far I have cut out the window and door, framed the office in, installed the window and door, done some preliminary painting, wired in electricity for the entire unit, added an internet line, run underground wiring to the main house, installed insulation and vapor barrier and last but not least, added the drywall. I would have to say the worst is over and now I look forward to more of the finishing work like painting, flooring, connecting the electrical plugs and lighting fixtures.
The only real big jobs left to do would be painting the outside of the Sea Can and spray foam insulating the shooting range area but the spray foaming I will be contracting out and getting it done professionally so that part will be easy at least!
Yup, another Shipping Container Project Update Video! For those of you interested in this project I am sure you have been waiting with baited breath ;) And for those wanting more airgun videos you are probably wondering when I will resume making more... Heck, I'm with you on that one, this manual labour stuff is way harder than making airgun videos, but it is all for the greater good. I will try and slip in some airgun related videos before this Shipping Container Project is finished, that's almost a promise!!!
At this point I am almost ready for drywall, all the electrical is completed including running the power and Internetunderground to the poorhouse and main house. I need to have my Internets at full jam, that's a must!
This week I will be getting the electirfcal all hooked up to the main box, adding isulation and vapour barrier, some more window baar cleanup and painting and by end of the week I hope to have the drywall in place along with the taping and first layer of mud.
Oh yah, this video also includes a huge bonfire, every spring and fall we usually burn all the fallen branches and yard debris, everyone comes out and enjoys the huge fire :)
The Shipping Container Project is moving along nicely, this past week I finished up my office area framing, I also got the door and window cutout and installed! Next up on my list is cleaning up and painting the window bars so I can make the unit a bit more secure. I suppose I will have to do the same with the metal door since it is in dire need of a facelift. Once the doors and windows are all taken care of I will be moving on to the electrical and wiring. My goal is to get all of this done by end of week... The sooner I get this Shipping Container Project done the sooner I can get back to making even better and more consistent airgun videos in my new home.
This week I started framing in my new office and in this video I show the wall closest to the airgun range where the door and shooting opening are situated. I managed to frame the back wall in too. I also talk about how much time it takes even before you pick up a drill or hammer simply planning everything out and acquiring all the supplies required for a project like this. I have spent a ton of time researching what I need to make this Shipping Container Project into the vision I have for it. Spoiler alert, in my next video the framing is all done including the installation of my window and outside door, glad that part is over!
No need to hunt for deals this Easter, EVERYTHING in our store is on sale! So kickoff your long weekend with a long-barreled revolver. Celebrate spring’s arrival with a spring powered sniper rifle. Or treat yourself to a hollow chocolate bunny and some hollow point pellets. This deal ends soon, so hop to it!
Lately I have been doing a lot of sourcing out figuring out how everything is going to be laid out, what kind of lighting I want to use, how am I going to heat the office area in my shipping container. I want to keep everything pretty low power so my plan is to go with all LED lighting and a 400 Watt heater which should be
fine in my 90 square foot insulated office space. I plan to blast the shooting range with some propane heat on days when I need it for the shooting testing during the colder months.
I did pickup some hardwood flooring pretty cheap at Big Box Store and also got my 3x6 office window from Surrey New and Used. I already have metal doors that my father-in-law has had stashed away for several decades but at least now they are going to come in handy.
The first job or actual work I needed to do on the Shipping Container Project was to level and place the Sea Can onto some bricks/slabs, this also helps to keep the underside dry so it does not rust out. There shouldn't be much settling since the storage container is resting on my gravel parking area and the gravel goes right down about 1 foot deep to the hard pan.
Next on my list is starting the framing, figuring out exactly where the windows and doors will be and of course cutting the container to fit them.
This Vimeo video will be a little different than most, sorry no shooting and not even a single gun to show anywhere in this video! But it will lead to hopefully better shooting field test and table top videos down the road as I will have a dedicated space not only to work but to also shoot my review airguns.
Today, well actually yesterday a 40 foot shipping container (Sea Can) showed up at my house. This new metal box is going to be my airgun shooting range and office space combined. It will contain a 30 foot airgun shooting range closest to the rear doors so that I can open them and create a longer range if necessary. The front 10-12 feet of the container will be my work office space where. I will also use some of the container for storage.
Over the next few weeks I will be leveling the container, framing and insulating the office area, adding some electricity and lighting and of course completing some finishing work to the office space to make it more cozy. Eventually I hope to do some outside work giving the container some more curb appeal with a new coat of paint.
I plan to make more videos to share with everyone of the work progress as it happens so keep watching...
