Type: Blank revolver.

Manufacturer:RÖHM.

Model:Little Joe Belt Buckle.

Materials: Mostly metal with plastic grips.

Weight: .3 pounds (134 grams).

Barrel: Front firing.

Propulsion: Gun powder.

Action: Revolver, single action only

Ammunition Type: .22 caliber crimped blanks (6mm Flobert).

Ammunition Capacity: 5 rounds.

FPS: NA.

Trigger Pull: The trigger pull for the Little Joe blank revolver is single action only, you must pre-cock the hammer first to rotate advance the cylinder and ready the hammer to fire. I very short medium weight trigger pull with virtually no take-up is required to fire this tiny revolver at that point.

Accuracy: NA.

Build Quality: Even though in general blank/signal guns do utilize scaled down metals like zinc alloy (not high pressure gun steel), the ROHM line of blank pistols are made very well and many of the internal mechanical parts, pins and screws are solid steel. The fit and finish is excellent and when I tested my none belt buckle Little Joe it shot flawlessly for me. Don't expect much recoil from the small acorn .22 rounds.

Realism: The ROHM Little Joe Belt Buckle 6mm Flobert Blank Gun is not a true replica of any real steel revolver in production but it does look a bit like the North America Arms NAA22s Mini-Revolver chambered in .22 short. North America Arms even has a belt buckle version of their own!

ROHM Guns Available in the: Replica Airguns Store

Pros:

• It’s a blank gun that fits into a belt buckle!

• German made Quality.

• Like the satin or stainless finish.

• Pretty much all metal gun with some steel in a few areas.

• Front firing revolver that will fir a flare adaptor.

• Uses inexpensive 22 Acorn blanks (6mm Flobert)

• Kind of rare in Canada, cool if you own one :)

Cons:

• Hard to get the Belt Buckle version here in Canada.

• Not sure about legalities actually wearing the belt buckle in Canada?

Comments:

I already thought the standard ROHM Little Joe Blank firing mini revolver was a really cool gun, to actually find one that fits into a belt buckle is even cooler! I wish we had these for sale in our Canada Replica Airguns Store but it's probably best we don't since I know some people will decide to wear theirs which is bad news since it's only a matter of time before a call is made and a lot of explaining is in order... The good news is we do sell the none belt buckle version of the Little Joe .22 Caliber (6mm Flobert) Mini Revolver in our Canada Replica Airgun Store along with many other ROHM German quality blank pistols so check them out for sure!

My Vimeo Table Top Review for the ROHM Little Joe Belt Buckle 6mm Flobert Blank Revolver:

Buy ROHM Little Joe Belt Buckle in Canada

Buy ROHM Little Joe Belt Buckle in the US

Type: BB air pistol.

Manufacturer:EKOL.

Model:ES 66 / ES 66 C

Materials: All metal construction.

Weight: 2.03/2.13 pounds (920/968 grams)

Barrel: Metal rifled.

Propulsion: 12 gram CO2 x 1.

Action: Semi auto, single & double action.

Ammunition Type: 4.5mm BB's.

Ammunition Capacity: 15 round magazine.

FPS: 410.

Trigger Pull: The trigger pull with both the EKOL ES 66 CO2 BB Pistols is fairly heavy in double action mode as the hammer spring is fairly firm. In single action mode the trigger pull lightened up a lot and allows for more precise shooting when required. The double action pull is fairly long and the release point is fairly far back.

Accuracy: I have not shot either of these EKOL ES 66 styled airguns but I have conducted a similar test using a similar EKOL BB  Pistol, the EKOL ES 55 which is basically the same base gun with a different slide. I would expect all of the EKOL airguns to shoot about the same. Based on my past experience the ES 66 C and ES 66 should shoot right around 420 fps or more and get 1-2 inch groupings from 30 feet out. We will find out for sure when I conduct my official Field Test Shooting Review for them.

Build Quality: The EKOL ES 55 comes from a company that primarily makes blank pistols. EKOL makes this gun directly from a similar model (The EKOL Sava) that shoots blanks so in many ways the ES 55 and ES 66 are designed more like a real gun than an airgun. The EKOL ES 66 Series is all metal with rubber grips and feels fantastic in the hand. There are really no plastic parts to speak of and I could not find any quality concerns on these airguns at all! The Chrome finish is something you don't often see in airguns but does look nice, just watch out for those finger prints ;)

Realism: The EKOL ES 66 CO2 BB Pistol is not an exact replica but does look a lot like a browning Hi-Power other than some small cosmetic differences. The basic size and shape is very close. With the shorter EKOL 66 C, this similarity is harder to see.

Available at: The Canada Replica Airguns Store

Pros:

• All metal construction - very heavy and solid feeling gun.

• Expect to have decent accuracy and good power.

• Safety is actually a de-cocker but a nice touch.

• Nice full size drop out Magazine that holds the CO2 and 4.5mm Steel BB’s.

• Double and single action trigger / hammer.

• One of the few BB pistols with a rifled barrel.

• Nice wrap around ergonomic grips.

• Very unique airgun, not a lot of them around.

Cons:

• Some parts don't function - slide release - slide when CO2 is in the gun.

• No cutout ejection port.

• Sights are none adjustable.

• Double action is a bit heavy and trigger take-up is long.

Comments:

EKOL makes several blank guns and I have reviewed many of them back when we used to be able to import more varieties of blank guns here in Canada. What makes the EKOL airgun version kind of different than most airguns out there, is that it is made very similarly to the way EKOL makes their blank guns. Many parts are interchanged so in some ways the airgun is a lot like the blank gun version which one could say is a lot like how a real gun is made. What I am getting at here is that the EKOL ES 66 and ES 55 look and feel more like real guns than an airgun. Make sure to pick one of these EKOL airguns up before we run out, our supply for them is limited and when they are gone we may not be able to get any more?

My EKOL ES 66 CO2 BB Pistol Table Top Vimeo Video Review:

Buy EKOL CO2 BB Pistols in Canada

Type: BB Pistol.

Manufacturer:Gletcher.

Model: APS (Stechkin)

Materials: Metal & plastic.

Weight: 2.29 pounds (1040 grams).

Barrel: 5.5 inches, smooth bore.

Propulsion: 12 gram CO2.

Action: Blowback - single & double action.

Ammunition Type: 4.5mm Steel BB's.

Ammunition Capacity: 22 rounds.

FPS: 394fps (120m/s)

Trigger Pull: The trigger pull on the Gletcher APS Stetchkin is nice in both double and single action modes. Double action is fairly light as the hammer spring tension is moderate. The blowback operation will of course pre-cock the hammer allowing for single action shooting on almost all of your shots but the trigger pull length remains the same in both single and double action. The only difference is that in single action mode, the first part of the trigger pull, or should I say the take-up portion is much lighter until it gets to the hammer release point where you will notice more pressure and a short crisp release point.

Accuracy: I have done no preliminary shooting with this pistol so other than how the trigger feels I can not comment on the performance. The Gletcher APS Stechkin CO2 Blowback BB Pistol has a fairly long barrel length so it should get close to the claimed almost 400 fps and since the rear sight is adjustable for elevation I will be abel to make aim point adjustments up and down if need be. The slide does snap back with decent firmness so I am also expecting there to be a decent amount of blowback feel.

Build Quality: The Gletcher APS Stechkin CO2 Blowback BB Pistol is well made, the metallic dark grey finish looks really nice and the fit is good, not a lot of slide wiggle  and pretty much the entire pistol is metal including the frame, slide, trigger, slide catch-release, safety, hammer, magazine and inner and outer barrel. The only plastic parts would be the grips and some internal seals and o-rings.

Realism:The CO2 BB Gletcher APS is a 1 to 1 replica of the Stechkin Soviet Military sidearm, all the mechanical parts function just like you would find on the real steel version other than the full auto mode located on the safety, which has been disabled, perhaps for the European markets where full auto airguns are not allowed. The barrel opening and the stick magazine are the real only tell-tale signs that this is the airgun version rather than a real Stechkin.

Pros:

• One of the only 4.5mm BB shooting Stechkin replicas I have come across.

• Very solid and weighty gun. Mostly all metal.

• High capacity 22 round all metal stick magazine

• Blowback operation seems heavy, slide locks back on last round.

• Operational parts all work like they should (slide catch, safety, hammer, elevation adjustment, mag release)

• Field Strippable.

• Should be able to put a stock on it?

• Shooting performance pros yet to be determined… 

Cons:

• No reassessed barrel opening.

• Would have liked to have seen full size drop out metal magazine on this gun.

• Full auto feature disabled on safety

• Shooting performance cons yet to be determined…

Comments:

When I saw this pistol in the Gletcher catalog, I did not realize how large it actually was, I was expecting the Gletcher APS Stechkin to be a bit larger than the Makarov but it really does dwarf the Makarov. Being that it is a large pistol it does have some weight to it but it does not feel heavy for its size. The grips are long front to back but not overly thick side to side so even medium sized hands should be OK shooting this BB air pistol. I am really happy to see another historic airgun added to the available Replica Airguns at our disposal and it's a bonus that we also get this one with blowback operation.Let's hope the Gletcher APS Stechkin shoots as well as it looks!

My Vimeo Table Top Video of the Gletcher APS Stechkin CO2 Blowback BB Pistol:

Buy the Gletcher APS Stechkin in Canada

Buy the Gletcher APS Stechkin in the US

First off I have reviewed all of these ASG guns in the BB version which I will link to below so you can read the full reviews. The main difference with this review is that I am reviewing the 6mm Airsoft versions and in the case of the ASG Bersa BP9CC and ASG CZ 75D Compact, the only difference is the ammo they shoot, with the ASG CZ 75 P-07 Duty, my Airsoft version is not blowback whereas the 4.5mm Steel BB version I reviewed earlier did have blowback operation.

My YouTube video for these ASG Airsoft versions does go into a lot of detail on each gun but in this written review I will keep to the basics since you can get most of the detailed information already in my 4.5mm Steel BB reviews for each gun.

Here are the links to my 4.5mm BB Reviews:

• ASG Bersa BP9CC 4.5mm CO2 BB Pistol Review

• ASG CZ 75 P-07 Duty 4.5mm CO2 BB Pistol Review

• ASG CZ 75D Compact 4.5mm CO2 BB Pistol Review

Below are some of the sepcifications for these ASG CZ and Bersa Airsoft Pistols:

• All use 12 gram CO2 cartridges.

• All shoot 6mm plastic Airsoft BB’s.

• All have working slides.

• Bersa BP9CC has blowback action.

• CZ 75 P-07 Duty & CZ 75D Compact are single and double action.

• Bersa BP9CC is single action only.

• FPS: (Bersa BP9CC 400 fps - CZ 75D Compact 425+ fps - CZ 75 P-07 Duty 480 fps).

• Bersa BP9CC has a stick magazine with 15 round capacity.

• CZ 75 P-07 Duty has a stick magazine with 16 round capacity.

• CZ 75D Compact  has a full size metal drop out magazine with 15 round capacity.

• All replicas of their modeled after firearms.

• All are distributed by ASG (Action Sport Games) and made in Taiwan.

Pros:

• Bersa BP9CC love the design and how compact it is.

• Bersa BP9CC has good weight for its small size, metal slide, trigger, stick magazine, barrel, slide catch release.

• Bersa BP9CC is the only one with blowback action.

• CZ 75D Compact has a full size drop out metal magazine that holds CO2 and BB’s.

• CZ 75D Compact has nice comfortable rubberized grips.

• CZ 75D Compact is the only one with adjustable hop-up and adjustable rear sight.

• CZ 75 P-07 Duty has the highest fps at 480 claimed.

• CZ 75 P-07 Duty lots of metal parts: Slide, barrel, magazine, hammer, trigger, slide catch, safety, magazine release.

• CZ 75 P-07 Duty has a really nice double action trigger.

Cons:

• Bersa BP9CC slide only goes back part way, not a full cycle blowback operation.

• Bersa BP9CC does not have adjustable hop-up or adjustable sights.

• CZ 75D Compact has a plastic slide.

• CZ 75D Compact is a bit light weight especially with the magazine out.

• CZ 75 P-07 Duty does not have blowback operation.

• CZ 75 P-07 Duty does not have adjustable hop-up or adjustable sights.

Make sure to watch my more detailed Vimeo Video Review for these ASG Airsoft Pistols as I cover much more info than this written article.

Buy the Airsoft ASG Bersa BP9CC in Canada

Buy the Airsoft ASG Bersa BP9CC in the US

Buy the Airsoft ASG CZ 75D Compact in Canada

Buy the Airsoft ASG CZ 75D Compact in the US

Buy the Airsoft ASG CZ 75 P-07 Duty in Canada

More guns to show off! Good for you and me! In this update video I show you some very interesting guns indeed! As many of you are aware, the Baikal Makarov MP-654K CO2 4.5mm Steel BB pistol has been really hard to find new here in Canada, making the price of used ones escalate up into the $700+ price range for one in as new condition. Well for those looking to buy a Baikal Makarov MP-654K we have located some and have them for sale now in our Canada Replica Airguns store (Very limited supply). These are the 2013 PM new design models with the narrow grips and mags, they also have the recessed barrels and cut out extractor. We sell them in the blued version only.

Another CO2 BB pistol that has been out of stock for some time is the EKOL ES series. I reviewed the ES 55 CO2 BB Pistol a while back but until now have not been able to show off the ES 66 Series which is more browning high power looking in design. The good news is we have both the ES 55 and ES 66 CO2 4.5mm Steel BB Pistol in stock in our Canada Store. These guns are mostly metal with full size drop out metal magazines that hold the CO2 and BB's, they also shoot in both single and double action and have pretty decent power! We are now selling both the ES 55 and ES 66 series of guns in our Online Canada Store.

I've looked at several Gletcher Airguns over the last little while and finally got my hands on the Gletcher APS Blowback CO2 BB Pistol which is a replica of the Russian Stechkin Soviet Military sidearm introduced back in the 50's. It's kind of a bigger brother version of the Makarov, i was surprised at how large it actually was when i got my hands on it! The real steel version had the ability to shoot in both semi and full-auto but my Gletcher APS 4.5mm BB replica only shoots in semi auto. Again, checkout the full line of Gletcher Products in our Canada Replica Airguns Store.

Last but not least I have a neat little 22 crimped blank pistol to show everyone. What makes it unique is the fact that it fits inside a belt buckle! We do see the ROHM Little Joe 22 caliber crimped blank pistols in our online Canada Replica Airguns Store but not this belt buckle version, kind of a one off I got form my supplier, I will be keeping it ;)  Make sure to watch my ROHM Little Joe Video Review and see all the ROHM products available in our Online Store.

Buy Gletcher Steel BB Soviet in Canada

Buy Gletcher Steel BB Soviet in the US

Buy EKOL ES 66 CO2 BB Pistol in Canada

Buy Baikal Blued Makarov CO2 in Canada

Buy Rohm Little Joe Ultra in Canada

Type: BB Revolver.

Manufacturer:Gletcher.

Model:P08 (Luger Replica).

Materials: Metal & plastic.

Weight: 2 pounds (900 grams).

Barrel: 4.25 inches, smooth bore.

Propulsion: 12 gram CO2.

Action: Blowback Toggle - single action only.

Ammunition Type: 4.5mm Steel BB's.

Ammunition Capacity: 21 rounds.

FPS: 344fps (105m/s)

Trigger Pull: The trigger pull on the Gletcher P08 Luger is medium pull for a SAO style trigger, it has a fairly shot take-up with a nice release point. The trigger definitely looks the parts with it's crescent shape and exposed spring. I would expect this pistol to behave well in the target accuracy department, at least the trigger will not be the problem.

Accuracy: I have not done any preliminary shooting so far with this Gletcher P08 due to some pretty awful weather conditions in my area. We will have to see how well the Gletcher P08 CO2 Blowback BB Pistol performs in terms of accuracy and velocity once I get out and do a real shooting test with it

Build Quality: The Gletcher P08 CO2 BB Pistol is really well made overall, pretty much the entire pistol is metal except for the grips of course and has a really nice weight to it. The finish looks really nice and the fit is good, the toggle feels nice and tight and all the mechanical parts function smoothly.

Realism: With the exception of the metal stick magazine, the Gletcher seems to have all it's other parts in order, even a working Toggle with Blowback,  although the toggle does not lock back on the last shot! The Gletcher P08 certainly looks the part of a Luger P08, Gletcher has hidden 4.5mm the inner barrel by recessing it little bit and the CO2 screw is well hidden under the magazine. It would have been nice to have been able to field strip the Gletcher P08 but perhaps people will get into less trouble losing parts without this ability.

Pros:

• Mostly all metal, nice and heavy at 2 pounds.

• CO2 is well hidden.

• Recessed barrel adds to realism.

• 21 round all metal stick magazine.

• Realistic blowback toggle operation.

• Lots of working parts.

• True a very realistic SAO trigger design that seems to have a nice light trigger pull.

• Shooting performance pros yet to be determined…

Cons:

• Does not seem to be easily field strippable 

• Painty at the rear of the toggle seems to have chipped off a a bit.

• Would have liked to have seen a full size drop out metal magazine on this gun.

• Shooting performance cons yet to be determined…

Comments:

This is the third Gletcher pistol I have reviewed and I am really liking the products from Gletcher! I like that they offer some very unique Airguns that many other companies are not addressing. My Gletcher P08 does have some competition from Umarex and KWC but it has its own selling points for sure, I figure it fits in nicely right between the Umarex and KWC P08's in terms of offering realism and practicality. So now we have a few choices when it comes to purchasing a 4.5mm CO2 BB firing P08 Luger, choice is a good thing!

My Vimeo Table Top Video of the Gletcher P08 Luger CO2 BB Pistol:

Buy the Gletcher P08 Luger in the Canada Store

Buy the Gletcher P08 Luger in the US Store

Type: Pellet air Revolvers.

Manufacturer: ASG.

Model:Dan Wesson 6 and 8 inch Pellet.

Materials: Mostly Metal Design.

Weight: 2.25 - 2.3 pounds.

Barrel: Metal rifled (6 Inch Sliver - 8 Inch Black).

Propulsion: CO2 x 1.

Action: Revolver, single and double action.

Ammunition Type: .177 caliber pellets.

Ammunition Capacity: 6 rounds.

FPS: 426+.

Trigger Pull: The ASG Dan Wesson Pellet Revolvers have predictable triggers with the single action being a bit more consistent since the take up is short, and the release is fairly light. Double action mode is very usable without a lot of extra pressure required. I found I just wanted to shoot this gun in single action mode because it felt more natural being that it is a six shooter.You also want to take your time shooting since loading the pellets into each shell and then the shells into the cylinder takes a bit of time.

Accuracy: This is yet to be determined since I have not to date had the opportunity to get outside and shoot these Pellet firing Dan Wesson's. Based on the exceptional results I got shooting my Dan Wesson Steel BB versions from 30 feet away, I should be abel to crack an inch or two 6 round grouping if my shooting is on. In terms of fps performance, ASG claims the pellet versions to shoot around the same velocity as the steel BB versions. With that in mind, this should give the Pellet shooting Dan Wesson's the advantage for raw power, since the lead pellets are heavier than steel 4.5mm BB's.

Build Quality: Like the entire Dan Wesson Revolver line from ASG, the pellet series is no exception and the fit and finish is very good. Most of the revolver is metal with the exception of the grips which are a plastic with a bit of a rubberized texture to them. The modified rifled barrels are made out of hardened steel and similarly so are portions of the newly designed pellet loading shells. Overall these are improvements to the quality of the Pellet shooting Dan Wesson Revolvers over the BB and Airsoft Dan Wessons.

Realism: The ASG Dan Wesson revolvers are as close as you can get to a real six shooter. Loading and ejecting actual shells into the cylinder makes you feel like this gun is much more then an unassuming airgun! If you want that real revolver experience than a shell loading Dan Wesson is the way to go, and the addition of a rifled barrel and lead pellets to the Pellet firing version should make the shooting experience even better.

Purchased From: The Replica Airguns Store.

Pros:

• It's a revolver with actual shells! Gives you the feeling of a real 6 shooter.
• Almost all metal design.
• Lots of detail in this gun, very well made, fit and finish is very good.
• Should have good power and good accuracy. Even better than the BB versions!
• Adjustable rear sight for windage and elevation.
• Barrel and shell redesign are a big improvement over the BB shooting versions.

Cons:

• Has a plastic CO2 screw tab.
• Loading pellets does take longer than the BB versions.
• May use more CO2 per shot than the BB versions because of heavier ammo. 

Comments:

Since I can't comment too much on the shooting experience these Pellet Dan Wessons will offer, I can say I am impressed with how ASG did the redesign of the inner barrel and pellet loading shells. It is obvious that ASG didn't just grab some parts of the shelf and quickly modify a BB version to shoot Pellets. ASG did it right and you can see the new adapted parts are of high quality and are even an improvement over the BB versions in many ways. On paper the Pellet shooting Dan Wesson's should be more accurate especially out at further ranges than the BB shooting Dan Wesson's and the Pellet versions should also hit the target with more force since they shoot a heavier projectile at around the same fps as the 4.5mm Steel BB version.

My YouTube Video Review for these Dan Wesson Pellet shooting Revolvers:

Buy Dan Wesson Revolvers in Canada

Buy Dan Wesson Revolvers in the US

Yes! Some new guns for you, and that's always a good thing for everyone, especially me since I get to play with them! I have been waiting a while to get my hands on some of the .177 caliber pellet shooting versions of the Dan Wesson Revolvers. I was actually introduced to them nearly a year ago at the last SHOT Show back in January of 2014! That's a long wait for sure...

The Pellet version Dan Wesson's look really good, the quality of the pellet shells is top notch and even the redesigned inner rifled barrels look to be very high quality. ASG did not just do a quick part swap, they really though out how they wanted everything to fit together. I am looking forward to seeing how well they shoot and will be Field Testing them both together so we can see how the barrel lengths play an effect on power and accuracy.

Next up we have two Gletcher pistols, both are classic semi auto shooters from the past, the Gletcher TT which is a Replica of the Russian Tokarev, and the Gletcher P08 which is a Luger copy. Both pistols are blowback and shoot 4.5mm Steel BB's.

Both pistols incorporate single action only triggers, metal stick magazines and working safeties, a real steel Tokarev normally would not have a safety other than the half cock hammer, Gletcher added in a discreet switch style safety on the right side of their TT. Again, I look forward to shooting both of these blowback pistols as soon as the weather picks up!

Buy Dan Wesson Revolvers in Canada

Buy Dan Wesson Revolvers in the US

Buy Gletcher Pistols in Canada

Buy Gletcher Pistols in the US

It's that time once again for an end of the year Gun Collection video. And no I will not be showing off all of my guns, to show and explain them all (Approximately 200 or so?) would simply take a really long time to make and a really long time for you to watch ;)

So like last years Gun Collection Video, I take a look at some of my favorite guns from 2014.

Here is a list of the guns featured in this Collection Video with links to their original reviews: 

• Umarex Makarov Ultra CO2 Blowback BB Pistol

• Umarex Beretta 84 FS CO2 Blowback BB Pistol

• KWC Mauser M1932 CO2 Blowback BB Pistol

• Umarex C96 Mauser CO2 Blowback BB Pistol

• ME8 General 8mm Blank Pistol

• Gletcher NGT CO2 BB Revolver

• Umarex Colt Commander 1011 CO2 Blowback BB Pistol

• Cybergun KWC Tanfoglio Gold Custom CO2 Blowback BB Pistol

• KWC P-08 Luger CO2 Blowback BB Pistol

• KWC 357 6 Inch Chrome CO2 BB Revolver

• Umarex Colt Python 357 CO2 BB Revoler

• Gletcher M1891 Sawn Off Mosin Nagant CO2 BB Rifle

• ASG CZ P-09 Duty CO2 Blowback Pellet Pistol

• Gamo MP9 CO2 Blowback Pellet Gun

Type: Blank Pistol.

Manufacturer: Bruni.

Model:Mod. 92 (Beretta 92).

Materials: Mostly Metal with some steel parts.

Weight: 2.8 pounds unloaded. (1274 grams)

Barrel: Top Venting. (No Red Tip)

Propulsion: Gun powder.

Action: Single and double action.

Ammunition Type: 8mm P.A.K. Blanks.

Magazine Capacity: 15 rounds.

FPS: N/A.

Trigger Pull: The trigger pull on the Bruni Mod. 92 Top Venting 8mm PAK Blank Pistol is fairly decent on both single and double action with a fairly long take-up in double action and of course a much shorter lighter take-up in single action mode.

Accuracy: NA.

Build Quality: The overall build quality of the Bruni Mod. 92 Blank Pistol is good, mine does show some wear since it is an older previously owned blank gun but for the most part the wear and tear is cosmetic only, the mechanical parts all seem to be in excellent working order. Most of this blank shooter is made out of a zinc based metal with a few steel parts, mainly the screws, pins and springs. But it has an impressive weight to it! The grips seem to have been replaced with wrap around rubber grips that may actually be for a real steel Beretta M92.

Realism: The Bruni Mod. 92 8mm P.A.K. Blank Pistol is a very realistic looking Beretta 92 in terms of overall looks and true to scale size and weight. Most of the parts work as you would expect them to on the real steal version including the double and single action trigger, safety, locking slide catch release and magazine release button. The only exception really is the fact that this version is top venting so there is a small hole just in front of the breach that allows the full discharge of the blank round to escape out the top of the blank gun. The barrel is actually fully plugged but seems to have been partially drilled out to give the impression of being a front firing gun.

Purchase from: A private collector.

Pros:

• Well made, materials fit and finish is all very good even though very little use of hardened steel.

• 15 round double stack magazine is nice hi-capacity.

• For a used gun it is in very good working condition, some minor wear mainly on finish.

• Barrel has been partially bored out to look like a front firing gun.

• Grips have been replaced with what looks to be real Beretta grips.

• It's a very close Beretta Model 92 replica!

• Made in Italy.

Cons:

• Top venting instead of front firing

• No actual take down lever for easy field striping

• Finish is a bit worn.

Comments:

In terms of being a very accurate Beretta Model 92 replica, the Bruni Mod. 92 8mm P.A.K. Blank Pistol is very close in almost all areas. Sure I would have liked it to of been front firing but the reality is, I rarely get around to shooting my blank guns. My blank pistols are mostly for show and since actual replica only guns are prohibited, being a blank gun skirts around our Canada laws allowing for ownership. Don't forget we sell the ROHM Blank guns here in our Canada Online Store and they are very good quality guns so check them out if you are in the market for a blank shooter.

My Vimeo Full Video Table Top Review for the Bruni Mod. 92 8mm P.A.K. Blank Pistol:

Buy Blank Guns in the Canada Store 

Buy Blank Guns in the US Store

A while back I made a full Table Top Review and Field Test Shooting Review for my sample - pre-production KWC Mauser M712 Broomhandle CO2 Blowback Airsoft Pistol. Well we finally got the finished product in our Canada Replica Airguns Store and not only in the 6mm Airsoft version but also the 4.5mm Steel BB versions!

I most likely will not be doing another table top review for the KWC Mauser M712 Broomhandle CO2 Blowback BB and Airsoft Pistol since I already made a fairly comprehensive Table Top Review of my sample - pre-production Airsoft unit. The only real difference I could find visually is the markings on the left side of the receiver indicating the pistol is made by KWC in Taiwan and the Caliber it shoots.

I will however be making a side by side Field Test Shooting Comparison Video to see if the production Airsoft version shoots the same as my pre-production model and also how the 4.5mm steel BB version compares in terms of fps and accuracy side by side.

We also have magazines for both of these KWC pistols in our Canada Store!

Make sure to watch my Vimeo Update Video where I show these two very realistic KWC Mauser M712 Broomhandle CO2 Blowback pistols in detail:

Buy the KWC Masuer M712 in the Canada Store

Buy the KWC Masuer M712 in the US Store

Type: Airsoft revolver.

Manufacturer:KWC.

Model:357.

Materials: Mostly metal with some plastic construction.

Weight: 2 pounds (900 grams).

Barrel: 2.25 inches, non-rifled.

Propulsion: 12 gram CO2.

Action: Revolver, single & double actions.

Ammunition Type: 6mm plastic Airsoft BB's.

Ammunition Capacity: 6 rounds.

FPS: 360+.

Trigger Pull: The trigger pull on the KWC 357 2.5 Inch CO2 Airsoft Revolver is good in both single and double action, even better than the Dan Wesson and S&W 327 TRR8 shell loading revolvers, most likely because the spring tension that pushes the inner barrel to make contact with the cylinder is noticeably lighter on the KWC 357's. Even the hammer is smoother and has less wiggle, just a better trigger and hammer mechanism overall.

Accuracy: This is yet to be determined but I did notice on the KWC Airsoft versions of their shell loading Airsoft Revolvers, that they do have a built in preset Hop-up by way of a small rubber bar that goes along the top of the barrel just inside the rear portion. This will create some backspin which will keep the Airsoft BB's trajectory more level but should also help them stay more accurate in general as compared to a plastic Airsoft BB that is not spinning but rather just floating through the air.

Build Quality: The KWC 357 2.5 Inch CO2 Airsoft Revolver being mostly metal has a very good build quality, perhaps even better than the Dan Wesson and S&W 327 TRR8 shell loading revolvers, even the weight of the KWC 357 is noticeably more! The only real plastic or rubber I could find was in the grips and the shell tips. Fit and finish was also good with no noticeable wear or sloppy workmanship.

Realism: The KWC 357 2.5 Inch CO2 Airsoft Revolver overall is a close copy a the real steel 357 styled revolver. I did notice the rear portion of the receiver (between the rear cylinder and hammer) to be a bit longer perhaps to accommodate the CO2 valve length, but other than that this pistol is super close to the original 357 styled revolver it is based on. Again being all metal gives this CO2 Airsoft revolver very realistic weight and feel and the loadable brass shells make using this gun almost exactly like using a real shell loading revolver but for much less cost per shot and of course a lot less recoil on the hands that a real 357 magnum or even when shooting 38 special shells for that matter ;)

Available in the:Replica Airguns Store.

Pros:

• Shell loading revolver adds to the realism!

• Mostly all metal design.

• Pretty all the parts work as they would in a similar real steel revolver of this type.

• Good overall weight, Very dense because of the shorter barrel.

• Should have good overall power, accuracy and shots per CO2 (based on Colt Python testing).

• Fully adjustable rear sight for windage and elevation.

• Well hidden CO2 Screw.

• Recessed barrel.

• Not much white writing on the gun.

• Nice easy Trigger pull in both single and double action.

Cons:

• Short 2.25 inch barrel will rob power but the Dan Wesson style long barrel Airsoft revolvers are know to be a bit hot for some Airsoft games so this may be a good thing.

• Grips may be a bit large for people with small hands.

• All black sights with no white dots are not great on dark backgrounds or low lighting.

Comments:

The KWC 357 2.5 Inch CO2 Airsoft Revolver is yet another addition to the increasing lineup of shell loading revolvers available today in both Steel BB and Airsoft versions. The 2.5 inch reviewed here is meant to be the compact version with its snub nosed barrel but I would have to say it is not a small gun at all coming in at 2 pounds and with rather large grips and a pretty large cylinder to pack around. But then again, that may be just what you are looking for? The shorter barrel will lower the fps a bit which may bring it back in line with the requirements of some Airsoft fields and the addition of the built in preset Hop-up, this pistol should shoot pretty well out at medium and even longer ranges.

My Vimeo Table Top Review for the KWC 357 2.5 Inch CO2 Airsoft Revolver:

Buy Airsoft Pistols in Canada 

Buy Airsoft Pistols in the US

Buy theKWC Black 2.5 Inch Airsoft Revolver

Type: BB Airsoft Pistol.

Manufacturer: KWC.

Model:Model 226-S5 (Sig Sauer X-Five).

Materials: 99% all metal build.

Weight: 2.75 pounds.

Barrel: 4.33 inches, brass, non-rifled.

Propulsion: CO2 x1.

Action: Semi auto blowback, double and single action.

Ammunition Type: Airsoft 6mm plastic BB's.

Ammunition Capacity: 25 rounds

FPS: 390

Trigger Pull: The trigger pull on the KWC Model 226-S5 Sig Sauer CO2 Blowback Airsoft Pistol is what you would expect from a blowback pistol with true single action capability. nice and light with a short take-up in single action and also decent when shooting in double action which for the most part you will not be doing since the blowback pre-cocks the hammer for single action shooting.

Accuracy: This is yet to be determined since I have not conducted my Field Test Shooting review for the KWC Model 226-S5 Sig Sauer. Based on my previous review of the Cybergun branded and licensed Sig X-Five 4.5mm Steel BB version, it should do well with heavy blowback, reasonable power but not a lot of shots per CO2.

Build Quality: Very good, pretty much an all metal construction, good weight and craftsmanship, slide wiggle is minimal, fit and finish is good. As with many of the KWC airguns that use an electromagnetic powder coating, the finish looks great but is thin so it does wear off on the high posts and where metal on metal movement takes place.

Realism: Compared to the real steel Sig Sauer X-Five, the KWC version is pretty close, although it does have a bit different looking slide in terms of the groves or slide serration's, and of course there is no Sig Sauer licensing on the KWC version. You also do not get the ugly white warning instructions so there is a bit of a trade off here and the KWC version also comes with a fully adjustable rear sight which is nice if your aim point is off a bit. Over all the KWC Model 226-S5 Sig Sauer CO2 Blowback Airsoft Pistol is super realistic with its full blowback operation, full size drop out metal magazine and ability to filed strip just like the real steel Sig Sauer it replicates.

Available From: The Replica Airguns Store

Pros:

• All metal construction - Extremely good weight and solid feeling gun. As real as you can get.

• Heavy blowback action.

• Accurate X-five replica without the Sig Licensing or white warning instructions.

• Awesome training gun.

• Both SA & DA with excellent trigger pull, very smooth and light.

• Has the fully adjustable rear sight for windage and elevation.

• Nice high capacity full size drop out metal magazine.

• Fully field strippable.

Cons:

• Top loading magazine only.

• Sacrifice some fps and shots per CO2 because of the heavy blowback but worth it.

• Finish is prone to wear on the high spots and metal on metal areas 

Comments:

I am really looking forward to my Field Test Shooting video for this Airsoft pistol, the KWC Model 226-S5 Sig Sauer is a nice big heavy pistol with lots of blowback, right up my alley! I am hoping the hop-up will keep this gun in the same accuracy zone as the 4.5mm Cybergun X-Five version, I may just have to test them head to head to find out? If you're a Sig Sauer fan like me, and require a solid useable Airsoft pistol for gaming or just plinking, the KWC Model 226-S5 Sig Sauer CO2 Blowback Airsoft Pistol should do the job well and at a price point that is very reasonable.

My Vimeo Videos for the KWC Model 226-S5 Sig Sauer CO2 Blowback Airsoft Pistol:

Buy the KWC Model 226-S5 in Canada 

Buy Airsoft Pistols in the US

Type: BB air revolver.

Manufacturer:KWC.

Model:357.

Materials: Mostly metal with some plastic construction.

Weight: 2.75 pounds (1218 grams).

Barrel: 5.5 inches, non-rifled.

Propulsion: 12 gram CO2.

Action: Revolver, single & double actions.

Ammunition Type: 4.5mm steel BB's.

Ammunition Capacity: 6 rounds.

FPS: 400fps.

Trigger Pull: The trigger pull on the KWC 357 6 Inch CO2 BB Revolver is good in both single and double action, even better than the Dan Wesson and S&W 327 TRR8 shell loading revolvers, most likely because the spring tension that pushes the inner barrel to make contact with the cylinder is noticeably lighter on the KWC 357. Even the hammer is smoother and has less wiggle, just a better trigger and hammer mechanism overall.

Accuracy:Based on my results shooting the Umarex Colt Python 357 which is essentially the same gun in a different finish. The results I got shooting my 6 round group from a 30 foot out semi rested position where good overall. Vertically there was about a 2 inch spread while horizontally there was about a 1 inch spread. I did find the plastic tips on the brass shells seemed to be a bit tight at first and this is when I did most of my Chronograph and target shooting. I believe the tightness effected the consistency of the FPS which also effected the accuracy especially up and down. I did get one shot out of the Umarex Colt Python 357 well over the claimed 400 fps but again the fps was rather erratic most likely because of the snug BB fit due to shell break-in.

Build Quality: The KWC 357 6 Inch CO2 BB Revolver being mostly metal has a very good build quality, perhaps even better than the Dan Wesson and S&W 327 TRR8 shell loading revolvers, even the weight of the KWC 357 came in close to a half of a pound more! The only real plastic I could find was in the grips and the shell tips. Fit and finish was also good with no noticeable chrome wear or sloppy workmanship. It will be interesting to see how the Chrome finish wears over time...

Realism: The KWC 357 6 Inch CO2 BB Revolver overall is a close copy a the real steel 357 styled revolver. I did notice the rear portion of the receiver (between the rear cylinder and hammer) to be a bit longer perhaps to accommodate the CO2 valve length, but other than that this pistol is super close to the original 357 styled revolver it is based on. Again being all metal gives this CO2 BB revolver very realistic weight and feel and the loadable brass shells make using this gun almost exactly like using a real shell loading revolver but for much less cost per shot and of course a lot less recoil on the hands.

Available in the:Replica Airguns Store.

Pros:

• It's a revolver with actual shells! Give you the feeling of loading and shooting a real revolver.

• Mostly all metal design.

• lots of detail, well made, Chrome looks nice, not sure if it will ear better than the black finish?

• Good overall weight, heaviest out of all the shell loaders.

• Should have good overall power, accuracy and shots per CO2 (based on Colt Python testing).

• Fully adjustable sights for windage and elevation.

• Well hidden CO2 Screw.

• Recessed barrel.

• Nice easy Trigger pull in both single and double action.

Cons:

• Grips are a bit rough.

• Grips may be a bit large for people with small hands.

• Black rear sight may not be great on dark backgrounds or low lighting.

Comments:

The ASG Dan Wesson shell loading revolvers reintroduced me to the joy of loading and shooting a revolver which up until that point was not that realistic of an experience when using a BB or Pellet revolver. The KWC 357 6 Inch CO2 BB Revolver like the Umarex Colt Python 357 has taken it up a notch by adding just a bit more overall weight, a smother trigger and hammer mechanism and styling this revolver on the Classic 357 magnum platform. And all of this for even less than the cost of the original Dan Wesson shell loading series CO2 BB revolvers. If you're a revolver fan, make sure to grab one of these, the Chrome finish is really eye catching and would make a great addition to your revolver collection for sure.

My Vimeo Table Top Review for the KWC 357 6 Inch CO2 BB Revolver:

Buy the Umarex Colt Python 357 in Canada

Buy the Umarex Colt Python 357 in the US

Some more CO2 pistols I will be doing Table Top and Field Test video reviews for in the near future. Some of them I have already reviewed in different caliber versions, either 4.5mm Steel BB or 6mm Plastic Airsoft.

From KWC I show off two revolvers styled after the 357 and if you watched my Umarex Colt Python 357 Review then you will notice the similarities between these KWC made revolvers since they are all made by KWC. The Model 357 6 inch version is finished in Chrome and made to shoot 4.5mm Steel BB's while the KWC Model 357 2.5 inch shoots 6mm Plastic BB's and is in all black. At this time I do not have these KWC revolver listed in the Replica Airguns Canada Store but should have them listed fairly soon...

I also showcase three CO2 6mm Airsoft semi auto pistols from ASG that I have already reviewed in their 4.5mm Steel BB equivalents. The ASG CZ 75 P-07 Duty Non-blowback, the ASG CZ 75 D Compact Non-blowback and the ASG Bersa BP9CC Blowback.

Make sure to watch my quick Update Vimeo Preview Video for these fine CO2 pistols to see them up close and personal...

Buy Umarex Colt Python in Canada

Buy Umarex Colt Python in the US

Buy ASG CZ 75D Compact CO2 Pistol in Canada

Buy ASG CZ 75D Compact CO2 Pistol in the US

Buy ASG CZ 75 P-07 in Canada

Buy ASG CZ 75 P-07 in the US

Buy ASG Bersa BP9CC in Canada

Buy ASG Bersa BP9CC in the US

Type: BB air pistol.

Manufacturer:Umarex.

Model:Magnum Research Baby Desert Eagle.

Materials: Mostly plastic with internal metal parts.

Weight: 1 pound.

Barrel: 4.25 inches, metal non-rifled.

Propulsion: CO2 x 1.

Action: Semi auto, non-blowback, double action only.

Ammunition Type: 4.5mm steel BB's.

Ammunition Capacity: 15 rounds - Internal spring fed magazine.

FPS: 420.

Trigger Pull: The trigger on the Umarex Baby Desert Eagle is double action only, it is a very long trigger that has a medium to heavy pull weight with a very long take up and unpredictable release point. Shooting accurately and controlled will take some time in the saddle so to speak but can be achieved. This pistol is really for plinking at pop cans and such, shooting off hand for fun. My full Field Test Shooting Review to follow shortly...

Build Quality: The Magnum Research Baby Desert Eagle is pretty much all plastic with some internal metal parts. The only actual working external parts are the trigger and the cross bolt safety. The slide catch, hammer, slide mounted safety and take down lever are all moulded into the plastic of the gun and are none functional. Even the magazine is internal so no need for a magazine release here! In the case of the Baby Desert Eagle, perhaps less is more since there is very little to break off or go wrong with this simplistic BB shooter ;)

Realism: This is a very close replica in terms of looks only (not to scale) to the real actual Magnum Research Desert Eagle with licensed trademarks and all. Keep in mind this is the "Baby" version so it is significantly smaller and lighter than the Pellet shooting full size Magnum Research Desert Eagle which could actually be a benefit to those with smaller hands. But again if we are simply talking about "looking like" a Desert Eagle than the Umarex Baby Desert Eagle does look the part, well except for the strange looking slide trigger.

Purchased this form: The Replica Airguns Store.

Pros:

• Price is right at around $50.
• Will fit smaller hands much better than the full sized Desert Eagle.
• Has both a top and bottom picatinny rail for all your accessory mounting needs.
• Magnum Research Licensed.
• Not bad in terms of power, accuracy and CO2 usage combination.

Cons:

• Mostly all plastic.
• Very few actual working parts, only the trigger and cross bolt safety.
• Trigger is very long and kind of unpredictable.
• If you decide to mount the included top picatinny rail, you will not be able to use the pistols built in iron sights anymore.
• Unsightly screw holes on the left side of this air pistol.
• No drop out magazine of any type.

Comments:

OK, so I'm rarely thrilled with the lower budget plastic super simple BB pistols but they do have their place. The tend to work well and stay reliable since there are fewer parts and less mechanical gizmos to get messed up. When the shooting begins and the steel starts to fly, they point the same and they hit your target just the same and all for a lot less out of pocket fun. On the plus side the Umarex Baby Desert Eagle is a pretty decent looking Desert Eagle copy all be it a much smaller version so if you've always wanted the big boy version with it's super huge handle and rather steep price point, well now you can get it in a size and price reduced version that just may be all you really need...

Watch my YouTube Video Review for the Umarex Magnum Research Baby Desert Eagle:

Buy the Baby Desert Eagle in the Canada Store

Buy the Baby Desert Eagle in the US Store

Here is my follow up Shooting Field Test to my ASG STI Duty One Non-blowback Table Top Review. During this Field Test Shooting video review I not only shoot my Non-blowback STI Duty One version but I also compare it to the Blowback ASG STI Duty One to see if fps and accuracy are effected when adding Blowback to the equation? I shoot 5 rounds through my Chronograph with both guns to get an average fps and I also step back 30 feet and setup resting my hands on a sand bag and standing in the back for a fairly secure shooting stance. I did my standard 10 shot grouping for my accuracy test from 30 feet away.

Overall both guns performed similarly and as expected the Blowback did effect the fps but not as much as I expected it to? I was expecting the Non-blowback STI Duty One to be at least 50 fps faster but it was only around 20 or so. I am fairly certain since the fps os so close between the two guns, that you will get more shots form a CO2 out of the Non-blowback ASG STI Duty One since there is no CO2 being used to make the slide recoil back and forth. In the end the Non-blowback STI shot an average fps of 373 while the Blowback version shot an average fps of 356.

When it came to accuracy, both guns performed about the same getting about a 2 inch group from 30 feet back. The Blowback STI did spread the BB's out more from side to side perhaps because of the slide recoil while the Non-blowback ASG STI Duty One seemed to shoot Horizontally tighter.

Personally since both guns shoot almost as high of fps and both STI Duty One's seem to be about the same accuracy wise. Why not just go with the blowback version since you will be shooting in single action most of the time which allows for a faster and lighter trigger pull. The only real downside to the Blowback STI Duty One is perhaps a bit more CO2 usage but you can still expect to get around 100 shots per CO2 which is very good for a CO2 blowback pistol.

Buy the STI Duty One NBB In Canada

Buy the STI Duty One NBB In the US

Here is my follow up Shooting Field Test to my Umarex CP88 Competition Table Top Review. During this Field Test Shooting video review I not only shoot my CP88 Competition version but I also compare it to the non Competition CP88 version to see if fps and accuracy are effected when adding the longer barrel? I shoot 5 rounds through my Chronograph with both guns to get an average fps and I also step back 30 feet and setup resting my hands on a sand bag and standing in the back for a fairly secure shooting stance. Since the Umarex Walther CP88's have an 8 shot rotary magazine I went with an 8 shot grouping for my accuracy test from 30 feet.

Overall both guns performed similarly and as expected the longer barrel CP88 Competition had the higher fps with 424 average versus 347 average, but what was surprising was how much faster the CP88 Competiton shot. Right around 80 fps more which is significant considering there is only 2 inches more of added barrel length to the Umarex CP88 Competition version. I am thinking that perhaps my CP88 Competition test model was tuned a bit better at the factory?

When it came to accuracy, both guns performed about the same getting about 1 inch group from 30 feet back. This was not a surprise since barrel length has less effect on accuracy than most people think.

Both guns are a pleasure to shoot and will not only perform great shooting close up but if you go with the higher fps Umarex Walther CP88 Competition you will be able to shoot much further out because of the rifled barrel and decent fps performance.

Buy the CP88 Competition in the Canada Store

Buy the CP88 Competition in the US Store

Type: BB air pistol.

Manufacturer: ASG.

Model:ASG STI Duty One 1911 Non Blowback.

Materials: Metal slide and polymer frame.

Weight: 1.8 pounds.

Barrel: Metal non-rifled.

Propulsion: CO2 x 1.

Action: Semi auto blowback, single action.

Ammunition Type: 4.5mm BB's.

Ammunition Capacity: 20 round magazine.

FPS: 407.

Trigger Pull: The trigger pull on the ASG STI Duty One 1911 Non Blowback is fairly light in both single and double action. Take-up is the same in both modes but when in single action mode most of the trigger pull has little to no resistance until you get to the break point near the end where the hammer is released.

Accuracy: In an Earlier review I shot the Blowback version STI Duty One 1911 air gun at a target from 20 feet away in a free standing position, and it performed well getting a 1.5 to 2 inch grouping right in the center of the target. The rear sight is adjustable for windage which is always nice to have just in case you are shooting a bit to the left or right. For me there was no need to adjust the sights. My Chrony testing with an eight shot averaged result was 373 fps - very decent for a blowback pistol! It will be interesting to see how this Non Blowback version performs since there is more CO2 going to the BB and less gun movement without the Blowback operation.

Build Quality: ASG did a great job designing and making the STI Duty One 1911 Non Blowback BB gun, they didn't really compromise on anything other than going with a polymer frame! With that said all that important parts like the Slide, Slide Catch, Safety, Mag Release, Hammer, Barrel and Magazine are all metal. The fit and finish as with all the ASG air guns is very good!

Realism: The ASG STI Duty One 1911 Non Blowback version is a close replica to the real steel STI 1911, the only real giveaway is the trigger design, as a true 1911 trigger is not your typical lever type. Even with the different type of trigger the STI Duty One is a very good replica complete with STI licensing and trademarks.

Purchased From: The Replica Airguns Store.

Pros:

• No Blowback action but does have a working slide and slide catch.

• Adjustable rear sight for windage.

• Shoots in both single and double action.

• Good quality control, very well made, fit and finish is good.

• Should have good power and accuracy like the blowback version, perhaps even a bit better.

• May have even better CO2 usage than the already good blowback version.

• Metal drop out magazine.

• Good STI Replica.

• Holds really well in the hand.

Cons:

• Trigger is not true to the real steel 1911.

• No working grip safety like a real 1911.

• Polymer frame rather than a metal frame.

• CO2 can be hard to get out.

Comments:

In terms of comparing the Non Blowback version of the ASG STI Duty One 1911 to the Blowback version without actually shooting it, they are pretty much identical except for the double and single action trigger found on the Non Blowback version. Even the slide seems to work the same. The big difference will be when I shoot the Non Blowback ASG STI Duty One. Will it shoot with a lot more FPS and will the reduced slide movement give it more accuracy? I am assuming yes to both of these question but I guess we will all have to wait and see when I do my official Shooting Field Test Comparison...

Watch my Vimeo Video Review for the ASG STI Duty One Non Blowback CO2 BB Pistol:

Buy the STI Duty One NBB In Canada

Buy the STI Duty One NBB In the US

This Article and Video expresses my views and opinions on this matter and should not be taken as legal advice.

Main points covered:

• Uncontrolled Firearms do not require a Firearms License within Canada to own and operate.

• What is an Uncontrolled Airgun and Airsoft Gun?

• What is an Uncontrolled Blank Gun / Starter Pistols?

• What about Fully Automatic Airguns and Airsoft Guns?

• What about Replica Guns?

NOTE: Controlled Firearms require a POL (Possession Only License) , PAL (Possession Acquisition License) or R-PAL (Restricted Possession Acquisition License) within Canada to own and operate. 

MEMORANDUM D19-13-2

Firearm – a barreled weapon from which any shot, bullet, or other projectile can be discharged and that is capable of causing serious bodily injury or death to a person, and includes any frame or receiver of such a barreled weapon and anything that can be adapted for use as a firearm.

“Uncontrolled”firearms are those devices that, although falling within the definition of a firearm in the Criminal Code, are exempt from specific legal requirements of the Firearms Act and its regulations, as well as from other legislative provisions. “Uncontrolled” firearms should not be subdivided into any of the non-restricted, restricted, or prohibited classes. The following types of firearms are deemed “uncontrolled”:

Flare, blank, rivet and industrial guns: Any device that is designed exclusively for signaling, for notifying of distress, or for firing blank cartridges or for firing stud cartridges, explosive-driven rivets or other industrial projectiles, provided that the importer intends to use it only for the purpose for which it is designed.

NOTE: (Toy guns and starter pistols do not generally qualify as firearms. However, some toy or model guns and starter pistols may be designed with very realistic mechanisms or appearances (e.g., color, size, scale, translucency) and resembling a real make and model of a firearm. In such cases, they may be considered replica firearms even if they are made of plastic, die cast zinc, or other material.)

Low muzzle velocity/energy guns: Any barreled weapon that is not designed or adapted to discharge projectiles at a muzzle velocity exceeding 152.4 meters per second (500 feet per second) and at a muzzle energy exceeding 5.7 Joules, or to discharge projectiles that are designed or adapted to attain a velocity exceeding 152.4 meters per second (500 feet per second) and an energy exceeding 5.7 Joules. Both thresholds of 152.4 mps and 5.7 Joules must be exceeded for the firearm to be considered “controlled”. This requirement exempts firearms that fire below the threshold velocity with a standard projectile, but exceed the threshold velocity when fired with a high-velocity projectile. 

Airsoft guns and certain types of paintball guns or markers may qualify as a replica firearm, if the muzzle velocity of the projectile does not cause serious bodily harm and their external features are clearly designed to resemble a specific and readily identifiable make and model of a firearm. To be considered a firearm, within the meaning of the Criminal Code, an airsoft gun must have a muzzle velocity in excess of 111.6 meters per second (366 feet per second).

NOTE: This memorandum used to state when using a .20 gram BB but does not specify this BB weight anymore?

NOTE: The term air gun is a colloquial term referring to BB or pellet guns. Such guns operate either as spring- powered, gas-powered, or electrically powered. If the muzzle velocity of the air gun is less than 152.4 mps (500 fps)/5.7 joules but still able to cause serious bodily injury to a person, it may be considered an “uncontrolled” firearm. Airsoft guns and certain types of paintball guns may qualify as a replica firearm (see paragraph 49 of this memorandum).

Replica firearms:

“Replica firearm” is defined as any device that is designed or intended to exactly resemble, or to resemble with near precision, a firearm, and that itself is not a firearm, but does not include any such device that is designed or intended to exactly resemble, or to resemble with near precision, an antique firearm.

For a device to be a replica firearm it must meet all three requirements:

• (a) it cannot be a firearm, meaning it does not discharge a projectile with sufficient energy to cause serious bodily injury or death to a person. If the device is a firearm, then it cannot be a replica firearm (and vice versa);

• (b) it must resemble exactly, or with near precision, a real existing firearm of an identifiable make and model. With respect to visual examination, note that the maximum observing distance is one at which the equivalent make and model of the firearm can be identified. This distance will vary from one firearm make to the next. For example: A Luger pistol has a very distinctive silhouette as compared to other makes and is therefore more readily identified from further away. The examination of the object is something more than casual, but less than detailed. The device does not need to be so close that markings are identifiable; and

• (c) it cannot be designed or intended to exactly resemble, or to resemble with near precision, an antique firearm. 

RCMP Website "Air Guns"

1. Air guns that are "Controlled" Firearms for purposes of both the Firearms Act and the Criminal Code

These are air guns with both a high muzzle velocity (greater than 152.4 meters or 500 feet per second) and a high muzzle energy (greater than 5.7 joules or 4.2 foot-pounds). The "muzzle velocity" is the speed of a projectile at the instant it leaves the muzzle of a gun, normally expressed in meters per second or feet per second. The "muzzle energy" is the energy of a projectile at the instant it leaves the muzzle of a gun, expressed in joules or foot-pounds. Air guns need to meet both standards to be classified as "Controlled" firearms for purposes of the Firearms Act.

These high-powered air guns are subject to the same license and registration requirements as a conventional "Controlled" firearm. Owners and users are also required to store, transport, display and handle them safely in accordance with the regulations supporting the Firearms Act.

Usually, the manufacturer's specifications are used to determine what muzzle velocity and muzzle energy an air gun was designed to have. This information may be available in the user's manual or on the manufacturer's website. If the information is not available, individuals can call the Royal Canadian Mounted Police Canadian Firearms Program (CFP) at 1-800-731-4000 and ask to speak to a firearm technician to find out if the air gun is considered to be a firearm for purposes of the Firearms Act.

High-powered air rifles are generally classified as non-restricted firearms. However, the classification depends on the exact design of the air gun. Air rifles manufactured to resemble an assault rifle could be non-restricted, restricted or prohibited depending on the exact model imitated. High-powered air rifles would also be prohibited firearms if fully automatic or if they have a sawed-off barrel. They could also be restricted firearms if they have a folding stock that reduces the overall length to less than 660mm. 

Additional thought on this subject: Even though Uncontrolled Firearms are not governed by the same laws that apply to Controlled Firearms within the Firearms act and do not need to be handled or stored similar in the same way you are required to handle, transport and store a Controlled Firearm, we need to treat our Uncontrolled Airguns, Airsoft Guns and Blank guns with care and go over and above what is expected when had handle, transport and store them.