Related Posts:

• WEBLEY ALECTO .177 AND .22 CALIBER MULTI-STROKE PNEUMATIC TARGET PISTOL

• WEBLEY ALECTO - ZORAKI HP-01 .177 & .22 CALIBER PCP AIR PISTOL REVIEW

I have been wanting to do a Chrony test for my Webley Alecto as I didn't have a chronograph at the time of my original review. Today was the day I got around to it and I am really happy with the results I got. Mine came with the pressure release valve adjusted fairly conservatively. I imagine this is a generic setting that is set the same for both the .177 caliber and .22 caliber versions based on the lighter .177 caliber having a faster muzzle velocity and hittiing the 495 fps with less pressure required.

In the case of a .22 caliber pellet and it having approximately double the weight, the pressure release valve may be adjusted a bit on the light side, but I was only guessing and I wanted to make sure I didn't have an air pistol shooting over 500fps as this would make it a restricted firearm here in Canada and although I have my restricted firearms license, I didn't want to have this particular pistol governed by the rules and regulations of a restricted firearm.

So lets get to my results. I was using crosman premium 14.3 grain pellets for this test, far from the heaviest .22 caliber pellets you can get. I also tested my Webley Alecto out with one, two , three and even four pumps. Keep in mind pumping the Webley Alecto four times is not recommended by the factory and could cause long term damage to your Alecto. I did it with mine because I will ultimately get asked what an extra pump will give you in terms of extra fps. 

• One Pump: 270.9 fps

• Two Pumps: 390.5 fps

• Three Pumps: 449.8 fps

• Four Pumps: 487 fps & 496.3 fps

So as you can see, I did not go over 500 fps even with four pumps which is exactly where I wanted this pistol to be around. If you do decide to do the pressure release valve mod on your Webley Alecto, I would recommend you also test yours out on a chronograph just in case your results are different then mine, and keep in mind modifying the Webley Alecto could void your warrantee. The last thing you want to be carrying around is an illegal firearm!

Buy Webley Guns in Canada

Buy Webley Guns in the US

Related Posts:

• ASG CZ 75 P-07 DUTY AND DAN WESSON 6 & 8 INCH REVOLVERS COMING SOON!

• ASG CZ 75 P-07 DUTY AND DAN WESSON 6 & 8 INCH REVOLVERS NOW SHIPPING

• PREVIEW - CZ 75 P-07 DUTY - DAN WESSON REVOLVERS - COLT SPECIAL COMBAT

• UMAREX COLT SPECIAL COMBAT CO2 4.5MM BB PISTOL REVIEW

• ASG CZ 75 P-07 DUTY BLOWBACK CO2 4.5MM BB PISTOL REVIEW

Type: BB air Revolvers.

Manufacturer: ASG.

Model:Dan Wesson 6 and 8 inch.

Materials: Mostly Metal.

Weight: 2.25 - 2.3 pounds.

Barrel: Metal non-rifled.

Propulsion: CO2 x 1.

Action: Revolver, single and double action.

Ammunition Type: 4.5mm BB's.

Ammunition Capacity: 6 rounds.

FPS: 426.

Trigger Pull: The ASG Dan Wesson Revolvers have predictable trigers with the single action being a bit more consistent, not just in feel but in fps also. Double action mode is very usable without a lot of extra pressure required. I found I just wanted to shoot this gun in single action mode because it felt more natural with a six shooter.

Accuracy: I shot the pair of Dan Wesson Revolvers  at a target from 20 feet away in a free standing position, and they performed well getting a 1.5 to 2 inch grouping just to the left of the target. The sights are adjustable for elevation and windage so getting these guns centered on the bullseye would be very easy. My Chrony testing with a six shot averaged result was 395 fps for the six inch and 447 fps for the 8 inch Dan Wesson.

Build Quality: These fine revolvers are extremely well built, I am beginning to think just about any product from ASG would not disappoint me, after reviewing the Dan Wesson's and CZ 75 P-07 DUTY. The Dan Wesson BB revolvers are almost all metal with just a few components made out of plastic, like the handles and CO2 screw tab. The handles feel like a cross between plastic and rubber. The finish on the six inch silver Dan Wesson is amazing and looks just like polished stainless steel. The black eight inch version has an almost metallic speckled finish without the shininess.

Realism: The ASG Dan Wesson BB revolvers are as close as you can get to a real six shooter, ASG didn't leave any detail out and thought of a few I may have never even dreamt up! Loading and ejecting actual brass shells into the cylinder makes you feel like this gun is much more then an unassuming airgun!

Purchased From: The Replica Airguns Store.

Pros:

• It's a revolver with actual brass shells giving you the feeling of a real 6 shooter!

• Almost all metal design.

• lots of detail in this gun, very well made, fit and finish is excellent.

• Good power and good accuracy.

• Fully adjustable sights.

• If I could have dreamt up this gun I don't think I could have done as good a job!

Cons:

• Very hard to get this gun in North America.

• Plastic CO2 screw tab.

• Only shoots BB's, would have been cool to shoot pellets too.

Comments:

I'm not really a revolver person, or should I say I wasn't really a revolver person, well until I got my Dan Wessons! I felt this way because most of the air gun revolvers available look just like that - they look like air guns! The Dan Wesson BB revolvers showed me that an air gun revolver can be just as cool as any of my very realistic automatic air pistols in my collection. And if you where already a revolver fan then the Dan Wesson CO2 BB revolvers are definitely for you.

Buy Dan Wesson Revolvers in Canada

This post is for any of you lucky North American Baikal Makarov owners out there, or for anyone thinking of getting a Baikal Makarov MP-654k.

We had some custom CO2 screws made up that fit the Baikal Makarov's BB-CO2 magazine perfectly and make the Makarov replica look virtually identical to the real steel. It's kind of a shame the Baikal Makarov didn't come this way from the factory but at least now you have the option of improving on an already great product.

Flush Metal CO2 Screw for Baikal Makarov

C$17.99

Related Posts:

• BUNCH OF AIRGUNS COMING FOR A LOW COST REPLICA COMPARISON SHOOTOUT

• COLT DEFENDER - H&K USP - S&W M&P - MAKAROV REPLICA BB GUNS ARRIVE!

• COLT DEFENDER - H&K USP - S&W M&P - MAKAROV REPLICA BB GUNS COMPARISON REVIEW

• UMAREX MAKAROV CO2 4.5MM BB PISTOL REVIEW

• UMAREX H&K USP CO2 4.5MM BB PISTOL REVIEW

• UMAREX S&W M&P CO2 4.5MM BB PISTOL REVIEW

Type: BB air pistol.

Manufacturer:Umarex.

Model:Colt Defender.

Materials: Mostly metal construction with a few plastic parts.

Weight: 1.6 pounds.

Barrel: 4.3 inches, metal non-rifled.

Propulsion: CO2 x 1.

Action: Semi auto, double action.

Ammunition Type: 4.5mm BB's.

Ammunition Capacity: 18 round magazine.

FPS: 440.

Trigger Pull: The trigger pull on this gun is medium and a bit long, the break point is a bit hard to predict but once you get used to it being on the long side it shoots pretty good.

Accuracy: This was my second time shooting the Colt Defender at a target from 20 feet away in a free standing position, and again it performed about the same as the first time, with a decent 2 inch grouping. I think with practice, I could get this easily down to a 1.5 inch group.

Build Quality: As the Colt Defender is almost all metal, you can't really complain to much about the durability aspects of this gun. Where I was let down a bit was the lack of functionality. In other words - parts that normally served a purpose like the hammer, slide release, sight adjustments and rear safety - all where just molded into the metal gun and where only for show.

Realism: The Umarex Colt Defender is a licensed replica of the real 45 auto Colt Defender pistol. It is a close looking copy with the exception of the trigger mechanism.

Purchased this gun at : The Replica Airguns Store.

Pros:

• Almost all metal construction!

• Good accuracy and power combination.

• Very solid and durable air gun.

• Decent replica of the actual Colt Defender 45 auto.

<!-- google_ad_client = "ca-pub-9036472715040282"; /* Replica Airguns Content */ google_ad_slot = "1487049688"; google_ad_width = 468; google_ad_height = 15; //-->

Cons:

• Most of the mechanical parts are molded into the gun.

• I don't like the screw holes on the right hand side of the gun - a dead giveaway.

• I would have liked a drop out magazine.

• Ejection port metal material is only a plastic sticker.

Comments:

This is another low cost replica air gun from Umarex designed for the more entry level buyer. It's a very solid and well made gun being that it's mostly metal. There are many positive aspects about teh Colt Defender, it's fairly consistent and accurate, has all the Colt licensing and trademark, has a good 440fps, uses an all metal design, and comes in at a very affordable price.

My Vimeo Video Review for this Airgun:

Buy this gun in Canada   -   Buy this gun in the US

Related Posts:

• BUNCH OF AIRGUNS COMING FOR A LOW COST REPLICA COMPARISON SHOOTOUT

• COLT DEFENDER - H&K USP - S&W M&P - MAKAROV REPLICA BB GUNS ARRIVE!

• COLT DEFENDER - H&K USP - S&W M&P - MAKAROV REPLICA BB GUNS COMPARISON REVIEW

• UMAREX MAKAROV CO2 4.5MM BB PISTOL REVIEW

• UMAREX COLT DEFENDER CO2 4.5MM BB PISTOL REVIEW

• UMAREX S&W M&P CO2 4.5MM BB PISTOL REVIEW

Type: BB air pistol.

Manufacturer:Umarex.

Model:H&K USP.

Materials: Mostly Plastic exterior with metal magazine and internal parts.

Weight: 1.8 pounds.

Barrel: 4 inches, metal non-rifled.

Propulsion: CO2 x 1.

Action: Semi auto, double action.

Ammunition Type: 4.5mm BB's.

Ammunition Capacity: 22 round magazine.

FPS: 400.

Trigger Pull: The trigger pull on this gun is medium, it has a predictable break point and is easy to shoot.

Accuracy: This was my second time shooting the H&K USP at a target from 20 feet out free standing and again it performed about the same with a decent 2 inch grouping.

Build Quality: You would think as this air pistol is mostly all plastic on the outside, that it would seem cheap and not so well made, but in fact the opposite is true! The plastic is of very good quality and form looking at it you would think the slide was actually made out of metal. Many of the internal parts and the full size drop free magazine are made out of metal giving the H&K USP a very solid and hefty feel.

Realism: The Umarex H&K USP is a licensed replica of the real H&K USP automatic pistol. It is an extremely close looking and accurate copy.

Purchased this gun from: The Replica Airguns Store.

Pros:

• Good price for such a realistic looking replica - excellent prop gun!

• Good accuracy and power combination.

• Nice full size 22 round drop out metal magazine..

• Even though it has a lot of plastic, they used high quality materials.

<!-- google_ad_client = "ca-pub-9036472715040282"; /* Replica Airguns Content */ google_ad_slot = "1487049688"; google_ad_width = 468; google_ad_height = 15; //-->

Cons:

• No blowback.

• Would have been nice to have at least a metal slide.

• Slide catch is moulded into the frame and the slide does not function in any way.

Comments:

This is another low cost replica air gun from Umarex designed for the more entry level buyer. It's actually a very well made gun despite all the plastic parts and it even has all the H&K USP licensing and trademarks. There is a lot of good with the Umarex H&K USP, it's fairly consistent and accurate, has good fps, uses "good quality" plastic, and  comes in at a very affordable price.

My Vimeo Video Review for this Airgun:

Buy this gun in Canada   -   Buy this gun in the US

Related Posts:

• BUNCH OF AIRGUNS COMING FOR A LOW COST REPLICA COMPARISON SHOOTOUT
• COLT DEFENDER - H&K USP - S&W M&P - MAKAROV REPLICA BB GUNS ARRIVE!
• COLT DEFENDER - H&K USP - S&W M&P - MAKAROV REPLICA BB GUNS COMPARISON REVIEW
• UMAREX H&K USP CO2 4.5MM BB PISTOL REVIEW
• UMAREX COLT DEFENDER CO2 4.5MM BB PISTOL REVIEW
• UMAREX S&W M&P CO2 4.5MM BB PISTOL REVIEW

Type: BB air pistol.
Manufacturer: Umarex.
Model: Makarov.
Materials: Mostly metal with a few plastic parts.
Weight: 1.5 pounds.
Barrel: 2.8 inches, metal non-rifled.
Propulsion: CO2 x 1.
Action: Semi auto, double/single action.
Ammunition Type: 4.5mm BB's.
Ammunition Capacity: 18 round magazine.
FPS: 380.
Trigger Pull: The trigger pull on this gun is light to medium, in single action mode when the hammer is pre-cocked, the trigger is nice and light and easy to predict. When shooting double action the trigger first cocks the hammer and then near the end there is a break point where the hammer releases.
Accuracy: This was my second time shooting this gun at a target from 20 feet out free standing and again the Makarov performed well. The ability to shoot in single action, definitely helps with the accuracy.
Build Quality: Being an all metal gun (mostly all metal), makes the gun feel solid and sturdy. The only plastic parts I could find on the Umarex Makarov where the grips and the safety lever. The painted finish is nice but maybe a bit on the glossy side.
Realism: The Umarex Makarov is a licensed replica of the Makarov PM 9x18 Russian military and police pistol. It is a very close copy in both looks and feel. 
Purchased this gun from: The Replica Airguns Store.

Pros:

• Great price for an all metal licensed Makarov replica.
• Good accuracy and power combination.
• Sports both single and double action.
• All metal 18 round drop free magazine.

Cons:

• No blowback.
• The slide catch/release does not work, as it's moulded into the frame.
• Paint may be a bit glossy for some people.

Comments:
This is another low cost replica air gun from Umarex designed for the more entry level buyer. It's actually a very well made all metal gun complete with the Makarov licensing and trademarks. There is a lot to like about the Umarex Makarov, it's accurate, has decent fps, uses good materials, has a working slide and all at a very affordable price.

My YouTube Video Review for this Airgun:

Buy this gun in Canada   -   Buy this gun in the US

Related Posts:

• BUNCH OF AIRGUNS COMING FOR A LOW COST REPLICA COMPARISON SHOOTOUT
• COLT DEFENDER - H&K USP - S&W M&P - MAKAROV REPLICA BB GUNS ARRIVE!
• UMAREX MAKAROV CO2 4.5MM BB PISTOL REVIEW
• UMAREX H&K USP CO2 4.5MM BB PISTOL REVIEW
• UMAREX COLT DEFENDER CO2 4.5MM BB PISTOL REVIEW
• UMAREX S&W M&P CO2 4.5MM BB PISTOL REVIEW

Type: BB air Pistols.

Manufacturer: Umarex.

Models: Colt Defender - H&K USP - S&W M&P - Makarov.

Materials:

Colt Defender - Mostly metal with plastic grips.

H&K USP - Mostly plastic with an all metal magazine.

S&W M&P - Mostly plastic with an all metal magazine.

Makarov - Mostly metal.

Weight:

Colt Defender - 1.6 pounds.

H&K USP - 1.8 Punds.

S&W M&P - 1 pound.

Makarov - 1.5 pounds.

Barrel:

Colt Defender - Non-rifled Metal - 4.3 inches.

H&K USP - Non-rifled Metal - 4 inches.

S&W M&P - Non-rifled Metal - 4.25 inches.

Makarov - Non-rifled Metal - 2.8 inches.

Propulsion: CO2 x1.

Action: Semi auto.

Ammunition Type: Steel BBs 4.5mm.

Ammunition Capacity:

Colt Defender - 16

H&K USP - 22

S&W M&P - 19

Makarov - 16

FPS:

Colt Defender - 440

H&K USP - 400

S&W M&P - 480

Makarov - 380

Trigger Pull: On all these guns the trigger pull is about medium with a bit of a break near the end. Only the Makarov has Single Action capability which gives it a much nicer and lighter trigger pull when desired.

Accuracy:

Colt Defender - At 20 feet in standing unrested position I got about a 2 inch group from 10 rounds.

H&K USP - At 20 feet in standing unrested position I got about a 2 inch group from 10 rounds.

S&W M&P - At 20 feet in standing unrested position I got about a 1.5 inch group from 10 rounds.

Makarov - At 20 feet in standing unrested position I got about a 1 inch group from 10 rounds.

Build Quality:

Colt Defender - Mostly metal with plastic grips, the gun had good finishing and a hefty weight to it.

H&K USP - Mostly good quality plastic with a full metal, full size magazine that gave the gun a solid feel

S&W M&P - Almost entirely plastic, it felt more like a toy then a gun because of it's light weight and shinny finish.

Makarov - Mostly metal with plastic grips and safety. This gun has good weight, feel and finishings.

Realism:

Colt Defender - Even though this BB gun is mostly metal, there are not a lot of moving parts, most parts where moulded into the gun and un-operational with the exception of the trigger and magazine release button.

H&K USP - I found it easy to forget about all the plastic in this air gun because of the excellent detail, everything is exactly right where it's supposed to be!

S&W M&P - On paper this gun is the right size and shape and pretty much looks like the real S&W M&P. You just don't want to get too close or pick it up or the illusion is lost.

Makarov -  An overal good replica with a moving slide that's even filed strip-able. The paint is a bit shinny but it makes for a nice looking gun overall.

Purchased thes guns at: The Replica Airguns Store.

Pros:

• Colt Defender - Mostly metal, high FPS.
• H&K USP - Very realistic, full metal full size drop out magazine.
• S&W M&P - Surprisingly good accuracy, high FPS, drop out metal magazine.
• Makarov - Mostly metal, moving slide, double and single action, drop out metal slide.

Cons:

• Colt Defender - Most moving part are non-functional, no drop out magazine.
• H&K USP - More metal and a moving slide would have been a nice touch.
• S&W M&P - Lots of cheap plastic, no real weigh to it, parts mostly moulded into the air pistol.
• Makarov - No blowback, no slide catch, paint is a bit shinny.

Comments:

I had very low expectations for most of these guns based on their low price point. But in the end, I was impressed with at least a couple things about them each of them! I can honestly recommend all of them but just make sure you buy them for the right reasons... If you want a high FPS and accurate target BB pistol then take a look at the Umarex S&W M&P. If you want an all metal gun with lots of moving parts then the Umarex Makarov is probably for you. If you're looking for a very close replica that's got a full size drop out magazine then you probably want the Umarex H&K M&P. If you want something that is super solid and almost indestructible then get then the Umarex Colt Defender juts might fit that bill.

Buy these guns in Canada 

Buy these guns in the US

Related Posts:

• BUNCH OF AIRGUNS COMING FOR A LOW COST REPLICA COMPARISON SHOOTOUT

• COLT DEFENDER - H&K USP - S&W M&P - MAKAROV REPLICA BB GUNS COMPARISON REVIEW

• UMAREX MAKAROV CO2 4.5MM BB PISTOL REVIEW

• UMAREX H&K USP CO2 4.5MM BB PISTOL REVIEW

• UMAREX COLT DEFENDER CO2 4.5MM BB PISTOL REVIEW

• UMAREX S&W M&P CO2 4.5MM BB PISTOL REVIEW

My low cost Replica BB guns arrived today! The Colt Defender, H&K USP and S&W M&P came in standard clear plastic packaging while the Makarov was the only air gun packaged in a box which is always a nice touch!

Now I haven't shot any of these guns yet, but I did get the chance to open all the packaging and give them a quick once over. My opinions of some of these guns may change after shooting them, depending on how they do, but as it stands I will give my first impressions of the guns. I'm not going to get into all the details as I will be doing individual reviews on each BB gun down the road. So here's a few pros and cons for each replica BB gun based on their first impressions:

Umarex Colt Defender 4.5mm CO2 BB Pistol:

The Umarex Colt Defender is basically a nice looking and fairly heavy all metal BB replica that feels good in the hand and has the Colt markings. It has a medium trigger pull with fairly good finishing.

The down side, it has no removable magazine, and most of the guns external mechanical parts like the hammer, slide release and safety, are molded into the metal and are non-operational.

Umarex Makarov 4.5mm CO2 BB Pistol:

Next we have the Umarex Makarov, this one is probably my immediate favorite out of the bunch for reasons like: It came in a box and has a movable and removable slide. For the most part it is all metal including the drop out magazine. The trigger pull again is about medium and even the safety is in the right place and is actually functional.

Some of my dislikes for this gun are the non-functioning slide release, so even though in this picture it looks like the slide is locked back, it's actually not (I'll show you how I did this in the future video!!). There is also no blowback action with this gun but to be fair, non of the other guns in this comparison have blowback either!

Umarex Smith & Wesson M&P CO2 BB Pistol:

I'm sorry to say the Umarex S&W M&P so far is my least favorite of the bunch, but first let's be positive... It's the right size and shape, has all its bits and pieces and markings in the right places so it would make an excellent low cost prop gun for sure! It is also the only gun with fiber optic sights and it does have a drop out metal magazine.

Now for the bad. When you pick this gun up it just feels cheap and plasticy, more like a toy then a gun! the trigger is OK but it's just so hard to get over the weight and feel of this BB gun. I hope it is a dream to shoot, that might be it's saving grace for me.

Umarex H&K USP CO2 BB Pistol:

OK, so let's leave of on a good note. The Umarex H&K USP was a close second to the Makarov in terms of first impressions with these low cost replica air guns. Even though a lot of the gun is plastic, it has a good weight and feel to it, this is partially due to the full size drop out metal magazine. The Umarex H&K USP also has everything in all the right places including the H&K markings and it too takes advantage of using the safety lever as originally intended, not just molded into the frame for show. Non of the guns had overly heavy trigger pulls and the H&K USP was no exception.

On the down side, it would have been nice to have a metal working slide to finish it off, and even though the hammer moves when the trigger is pulled, it's really only for show as it does not stay back and allow for both single and double action operation. Instead you can only shoot in this gun in double action.

<!-- google_ad_client = "ca-pub-9036472715040282"; /* Replica Airguns Content */ google_ad_slot = "1487049688"; google_ad_width = 468; google_ad_height = 15; //-->

So that about wraps up this initial overview of my first impressions of the Umarex Colt Defender, H&K USP, S&W M&P, and Makarov Replica BB guns. Next I will be shooting a YouTube table top comparison review of these low cost replica BB guns, so make sure to check back!

Buy Blank guns in Canada

Buy Blank guns in the US

Related Posts:

• COLT DEFENDER - H&K USP - S&W M&P - MAKAROV REPLICA BB GUNS ARRIVE!
• COLT DEFENDER - H&K USP - S&W M&P - MAKAROV REPLICA BB GUNS COMPARISON REVIEW
• UMAREX MAKAROV CO2 4.5MM BB PISTOL REVIEW
• UMAREX H&K USP CO2 4.5MM BB PISTOL REVIEW
• UMAREX COLT DEFENDER CO2 4.5MM BB PISTOL REVIEW
• UMAREX S&W M&P CO2 4.5MM BB PISTOL REVIEW

I am a bit of a stickler for blowback air guns, and if they don't have blowback, then they have to offer other points of realism that will win me over. Like with the Baikal Makarov and how it's pretty much a real Makarov but converted to shoot BB's.

So in some ways I'm a bit of an airgun snob and I have tended to stay away from the lower cost replica air guns for reasons like: Too much plastics, no blowback, too many non-working parts... Well I'm throwing it all in the wind for this next batch of airguns I am going to review and compare. They all sell for well under $100 and some even below $50. What they all have in common is that they are decent looking replicas of the original guns they represent and they all happen to be made by Umarex.

The guns are availabe in the Replica Airguns Store:

Umarex Colt Defender CO2 BB Pistol

Umarex H&K USP CO2 BB Pistol

Umarex S&W M&P CO2 BB Pistol

Umarex Makarov CO2 BB Pistol

When they get here I plan to do a full side-by-side comparison review of these Umarex replica CO2 BB guns and compare them based on accuracy, build quality, realism and shoot-ability. So make sure to check back and see how these air pistols compare?

Buy these guns in Canada   -   Buy these guns in the US

Related Posts:

• FULL METAL UZI BLOWBACK CO2 .177 BB GUN ON ITS WAY

• CYBERGUN MINI UZI BB GUN REVIEW

• CYBERGUN MINI UZI CO2 BB GUN CHRONOGRAPH AND FULL AUTO SHOOTING TEST

"Before you attempt to do this modification you need to be aware that it may void your warrantee and/or you may fail and either break something or incorrectly reassemble your Mini UZI rendering it "Broked"! This is your problem so please do not attempt this modification (even though it is fairly easy to do) unless you're 100% confident you can do it and are aware of the possible consequences. Make sure to also take into account any gun laws in your area prohibiting full-auto capable firearms!"

(Special thanks to Herman for showing me the ropes on this modification)

This modification will make your semi-auto "only" Cybergun/KWC Mini UZI BB Gun into a full auto capable 4.5mm BB machine gun. From the factory the full auto switch position (Far Left "A") is disabled but the full auto selector position is visible. The actual full-auto functionality is still present in the Mini UZI but has been decommissioned by the simple means of blocking the selector switch from being moved to the far left full-auto or "A" position.

This full auto modification will show you how to disassemble the Cybergun - KWC Mini UZI BB Gun and remove the small plastic selector switch blockage so you will be able to manually switch between semi auto and full auto modes. This modification takes about 15 minutes to complete.

<!-- google_ad_client = "ca-pub-9036472715040282"; /* Replica Airguns Content */ google_ad_slot = "1487049688"; google_ad_width = 468; google_ad_height = 15; //-->

You will need the following tools: A pair of pliers and either a pair of small wire cutters or a file.

Let's begin! Below are the two pre-modification positions available from the factory:

"S - SAFE"

"R - SEMI AUTO"

Below is a closeup of the top bolt cover that we will be removing to access the internal bolt for removal:

In the next photo we have removed the bolt cover by pressing the "angled button" towards the rear sight:

And now the bolt is removed:

I removed the grips but this is not necessary:

Now you will need to remove the lower receiver pin located at the back end of the receiver closest to the grip safety. Use a pair of pliers to pinch the metal pin while pushing it through. Once the pin is started you can use the pliers on the other side to pull the pin all the way out. You may need to us a fair amount of force to do this as the fit of the pin is tight:

Once the pin is removed the lower receiver can be detached:

You can see in the picture below the small plastic nub that we will need to remove in order to restore full-auto capability:

I used a pair of small wire cutters to clip this plastic nub off, but you could use a file too. Just make sure that the plastic is flush and does not have any burs or protrusions.

Below is a photo of the Plastic Nub removed from another angle:

After that, all you need to do is reassemble you Mini UZI in revers order to finnish the Full Auto modification.

In the below Photos you can see we have restored the ability to move the fire selector switch over to the "Far Left" or "A" position, reenabling the Cybergun - KWC Mini UZI BB Gun to shoot in full auto when desired.

"A - FULL AUTO"

Now enjoy your Cybergun - KWC Mini UZI BB Gun in full-auto as it was originally designed!

Here is my Vimeo Video in Narrative with Photos:

Buy this gun in Canada

Buy this gun in the US

Related Posts:

• FULL METAL UZI BLOWBACK CO2 .177 BB GUN ON ITS WAY

• CYBERGUN - KWC MINI UZI BB GUN FULL AUTO MODIFICATION

• CYBERGUN MINI UZI CO2 BB GUN CHRONOGRAPH AND FULL AUTO SHOOTING TEST

Type: BB air pistol.

Manufacturer: Cybergun.

Model: Mini UZU.

Materials: Metal and Polymer.

Weight: 4.8 pounds.

Barrel: Metal, non-rifled.

Propulsion: CO2 x1.

Action: Semi auto (Selectable Full Auto with Mod) blowback, single action only.

Ammunition Type: Steel BBs 4.5mm.

Ammunition Capacity: 25 rounds

FPS: 344

Trigger Pull: The trigger pull is very light with an easy break.

Accuracy: Very good, even with all the heavy blowback recoil!

Build Quality: Excellent, with a good amount of metal construction, good weight and craftsmanship with good fit and finish. Much of the gun is made out of metal with the exception of some of the outer receiver and grips.

Realism: This is a very close replica of the actual real steel with many of the same markings in all the right places, It's hard to find any real differences other than the fact that it shoots 4.5mm BB's and has a bit more plastic.

Pros:

• Extremely realistic airgun replica of the Mini UZI.

• Metal construction where it counts.

• Would make an excellent training gun as it functions just like a real Mini UZI.

• Blowback action is incredibly firm (more than a rimfire 22 cal.) adding to the realism of shooting this weapon.

• Can be easily field striped.

• Can be easily modified to fire in either Semi Auto or Full Auto by removing one small plastic blockage.

• Adjustable sights.

• Very useful metal folding stock.

Cons:

• It goes through CO2 very fast.

• When the magazine is empty, the slide bolt does not stay open and the gun will continue to fire waisting CO2.

• Some of the outer materials are plastic, would have been nice if they too where metal construction.

Comments:

This is a really nice blowback BB gun. Although it is advertised on many websites as being all metal, it does have some plastic outer parts, but the parts that get the most wear and tear are made out of metal. That aside, the Cybergun Mini UZI is pretty much an exact copy of the real Mini UZI with many of the same markings as the original. One feature that makes it feel even more genuine is the very heavy blow back recoil, it is alarming at first and I would even say it has more recoil than a rimfire 22 cal. gun does. It only comes in a semi auto version but all Cybergun did to inhibit full auto mode was to simply add a plastic nub that stops the fire selector switch from being selected to full auto. Once this plastic nub is removed, full auto mode is resorted. This well made BB gun is a bit pricy but you get a lot of gun for your money!

Buy this gun in Canada

Buy this gun in the US

This Article was graciously provided by one of my viewers: Lee

Related Posts:

• SIG SAUER X-FIVE STAINLESS STEEL VERSION

DISCLAIMER, PLEASE READ AND UNDERSTAND!

• This walkthrough is for information purposes ONLY, if you decide to dismantle your BB gun you will void any warranty you have with the manufacturer.
•  I will not be held accountable for your actions or any damage that is caused by your negligence. Therefore, if YOU decide to dismantle your BB gun and break something during the dismantling or assembling it is your problem not mine.
• If you don’t feel confident or comfortable doing any of these steps STOP and do not proceed any further or you may do damage.
• YOU WILL LOOSE ALL THE SIG SAUER MARKINGS ON THE GUN.

Having said all that, this is my first ever instructional so I’m going to try and make this walkthrough as easy as I can for you to understand. You will need the following: Flat tip Screwdriver for the grips, Small Philips Head screwdriver, small punch & needle nose pliers – the last 2 are optional.

Make sure you have a clean work space and lay out every part in the order that you remove it Left to Right, come reassembly time you work Right to Left it makes reassembly so much easier.

Step 1:

Field Strip the slide until it looks like this:

Unscrew these 2 screws, these hold in the “Breech Block” once your unscrewed cup the end of the slide in your hand and let the Breech & Screws fall in your hand – Set these aside.

That’s it your Slide should look like this:

It is now ready for paint removal.

Step 2:

Take the Frame and start removing the grips Left hand side first:

Flip the frame over and remove the right hand side grips:

Carefully remove the trigger return spring, it is under tension and it WILL fly across the room – I spent an hour looking for it one day! Also while we are at it, you can remove the cover to the magazine release.

To remove the safety, place your flat tip screwdriver between the frame and the safety and twist ever so gently this will separate the safety and all you need to do now is grab the safety from either side and gently pull & wiggle until it separates.

Once the safety is removed you will see the safety bar, this lifts off.

Step 3:

Lift this little pin out and remove the spring, very carefully push this pin from the other side and remove, be careful because once this happens your hammer assembly is loose and free from the frame.

Slowly and gently remove the hammer assembly:

Note the little shiny piece that sits on the side of the hammer assembly, try very hard not to let this piece fly out, it is a pain to get back in, if it does fly out keep calm and take your time, don’t force the little spring in, it seats in behind the shiny metal thing – sorry I don’t have a proper name for it.

Also make sure that the spring next to it is in the locked open position, if it snaps back just get the tip of a small screwdriver and slide it to the left until it locks.

The hammer return spring assembly at the back of the grips can be removed and set aside.

Removing the trigger assembly is easier than it looks; you need to remove the takedown lever by rotating it counter clockwise until it stops.

Push it through the frame and rotate it back clockwise to remove it all together.

Remove the screw holding the trigger assembly:

Lift out the trigger assembly; be careful of the slide lock spring it wont Fly out, but it will fall out.

If you want to remove the magazine release, there is a spring that sits at the rear of the trigger guard;

Push the magazine release in part way & with the flat tip screwdriver lifts the up to remove it, once removed the magazine release will simply fall out.

THAT’S IT! We’re done, ready for the paint removal. Any paint stripper is fine.

KEEP IT WELL AWAY FROM THE PLASTIC PARTS!

Follow the manufacturer’s guidelines for use of their product and thoroughly clean the slide and frame after you have removed the paint.

YOU WILL LOOSE ALL THE SIG Sauer MARKINGS ON THE GUN.

Rub over the slide and frame with #0000 Steel wool or 1200 grit Wet & Dry paper. Clean again and using the paper or steel wool with some ALUMINUM polishing compound like Autosol and some good ol fashioned elbow grease polish the slide and frame until you reach your desired outcome. Clean it all down again and wipe it down with a rag that has had gun oil or my preference “Fluid Film”.

Reassemble the gun in the reverse order and viola one shiny SIG Sauer X-Five.

Buy this gun in Canada   -   Buy this gun in the US

Related Posts:

• CYBERGUN MINI UZI BB GUN REVIEW
• CYBERGUN - KWC MINI UZI BB GUN FULL AUTO MODIFICATION
• CYBERGUN MINI UZI CO2 BB GUN CHRONOGRAPH AND FULL AUTO SHOOTING TEST

I have been holding off and holding off on this gun for a while now but I just can't wait any longer! So today I finally ordered up a Full Metal UZI Blowback CO2 .177 BB Gun from the Air Gun Source here in Canada.

I'm not 100% sure who makes this full metal replica UZI BB gun but I believe it may be the Cybergun version. There seems to be identical version distributed by "Armist Industries" and "KWC", when it comes I should have more info about it. This UZI is stated to be "Full Metal" but I have heard conflicting stores and again when I get it I will update you on the quality of this nice UZI Blowback BB Gun.

These guns ship with a selector switch that has three positions: (A-R-S), one is the safety and the other two are semi-auto only. This gun does not ship with a full-auto feature but I have a  source who has converted his to full auto and he is sharing this information with me shortly. I plan to mod mine so it has a selectable semi auto and full auto.

This gun is reported to have a very heavy blow back action with significant shoulder kick for a BB gun. Sounds like fun! It has also been chronographed at 390 FPS! And it even comes with a folding Stock.

Here are some basic stats for you until I do my full review...

• 344 FPS*OUR TESTS SHOW 390 FPS!
• Full metal
• Blowback action
• Semi-auto
• Removable 25 round magazine
• Foldable metal stock
• Uses one 12g CO2 cartridge
• .177 calibre (4.5mm) BB's
• Length: 14"
• Weight: 4.85 lbs
• 30 Day Warranty
• Made in Taiwan

Buy this gun in Canada   -   Buy this gun in the US

Related Posts:

• SIG SAUER X-FIVE P226 TAKE DOWN FOR STRIPPING AND PAINTING

One of my viewers (Lee) sent me some pictures of their Cybergun Sig Sauer X-Five BB gun that he stripped down to the bare metal. His had some of the paint flake off so he decided to take it down to bare metal. It looks pretty good and he says with some of his "secret" metal oil on it, it stays rust free.

Here are some picts of it:

Buy this gun in Canada   -   Buy this gun in the US

You may be surprised to know that the Airgun that started off my collection was purchased only about 4 years ago. As a kid I had a few Airguns growing up and then suddenly in my late 30's I just picked it up again. Anyways the Airgun this post is focusing on is the Umarex Walther CP99 Compact. This post is not intended to be a review but in summary the CP99 Compact BB Blowback BB gun has one of the nicest trigger pulls in my collection. It is so much fun to shoot, it's very well made and is reasonably priced.

The one feature,or lack of a feature that I never really like about the Umarex CP99 Compact was the molded ejection port. In other words the ejection port is not cut out of the slide on this gun but instead is molded into the slide to look like an ejection port.

That said I have noticed a few of these Umarex CP99 Compacts sporting a cut out ejection port and so I thought to myself that maybe people have been cutting the ejection port out themselves? Hey I thought about giving it a try several times myself. So I took a walk over to the Umarex US website and low and behold if you click on the 360 view, you will see that it too has a cut out ejection port. The photos on their site do not show this new feature but rather the older molded version. I can not confirm that all new CP99 Compacts will in fact have the cut out ejection port, but it does look like Umarex has moved to this updated version…

So I thought enough is enough! It's time to pull out my tools and cut into my beloved CP99 BB gun. The best way to show you what transpired next is with a series of photos. At the end of about 2 hours of work I have to say I am very happy with the end result!

Buy this gun in Canada   -   Buy this gun in the US

Related Posts:

• CYBERGUN GSG 92 ON ITS WAY!

• CYBERGUN GSG 92 BB GUN REVIEW

• CYBERGUN GSG 92 BB GUN FIELD TEST

This video is not really a review but rather an instructional video on how to modify a Cybergun GSG 92 Blowback BB Airgun to shoot not only in single shot (Semi Auto), but to also have the ability to shoot in Full Auto mode with the flick of the safety to the down position. (Warning - This Mod will most certainly void your warranty!)

<!-- google_ad_client = "ca-pub-9036472715040282"; /* Replica Airguns Content */ google_ad_slot = "1487049688"; google_ad_width = 468; google_ad_height = 15; //-->

This Modifications of the Cybergun GSG 92 is a rather simple operation, all that is needed is to remove the slide and take off the right side grip, then remove a small internal piece and file it down slightly on one end. Put everything back together and away you go. Shoot in Semi Auto or Full Auto whenever you like!

I'll be doing a Review and Field Test on it shortly...

Buy this gun in Canada

Buy this gun in the US

Related Posts:

• UMAREX SA177 CO2 BB AIRGUN - FIELD TEST

• UMAREX HPP CO2 BB AIRGUN - FIELD TEST

I received both of these Umarex blowback BB guns (Umarex H.P.P and the Umarex SA177) about a month ago and so far I have very little to complain about either of them!

Some of the specs:

• Both of them are CO2 powered

• Both of them shoot 4.5mm BB's

• Both of them have blowback action

• Both of them shoot around 400 FPS

• The H.P.P  is styled after the Sig Sauer 266

• The H.P.P is mostly all metal construction

• The H.P.P has a 15 round magazine

• The SA177 is styled after the Glock

• The SA177 has a metal slide and composite frame

• The SA177 has a 19 round magazine

• The SA177 has fiber optic sights

Here is a quick summary of these airguns…

Both of these Umarex airguns are great value for the money and both shoot pretty hard and accurate for blowback styled BB guns. Both have long trigger pulls with the SA177 being a bit on the heavy side. Neither one has a very heavy blowback feel but there is enough blowback to make them responsive and fun to shoot.

The construction on both of these BB airguns is overall very good with the SA177 being more realistic in comparison to the H.P.P. The H.P.P tends to be a more comfortable gun to shoot because of its weighty feel in the hand and lighter trigger pull.

<!-- google_ad_client = "ca-pub-9036472715040282"; /* Replica Airguns Content */ google_ad_slot = "1487049688"; google_ad_width = 468; google_ad_height = 15; //-->

I highly recommend both of these air guns. If you're looking for realism then get the SA177, and if you want the better shooter of the two, get the H.P.P.

I will be doing a more thorough shooting review with videos for each one of these Umarex blowback CO2 BB guns in the near future so stay tuned!

Here is the Vimeo Video of my Umarex H.P.P and SA177 Comparison/Review:

Buy Umarex HPP gun in Canada

Buy Umarex HPP in the US

Type: BB air pistol.

Manufacturer: Cybergun.

Model:Sig Sauer X-Five P226.

Materials: 99% all metal build.

Weight: 2.6 pounds.

Barrel: 4.4 inches, brass, non-rifled.

Propulsion: CO2 x1.

Action: Semi auto blowback, double and single action.

Ammunition Type: Steel BBs 4.5mm.

Ammunition Capacity: 18 rounds

FPS: 330

Trigger Pull: The trigger pull is what you would expect from a real automatic pistol, in single action mode it is light and short.

Accuracy: Very good.

Build Quality: Excellent, with almost all metal construction, good weight and craftsmanship.

Realism: This is as close as you can come to the look, weight, feel, and action of the real Sig Sauer X-Five. P226!

Available From: The Replica Airguns Store

Pros:

• Extremely realistic airgun replica of the original Sig Sauer X-Five P226.

• All metal construction.

• Would make an excellent training gun as it functions just like a real automatic handgun.

• Blowback action is very firm adding to the realism of shooting this weapon.

• Field strips just like the real Sig Sauer X-Five P226.

• Carries Sig Sauer licensed trademarks

Cons:

• It goes through CO2 very fast.

• When the magazine releases, it simply drops out, no spring to it.

• No adjustable sights.

Comments:

This BB air pistol is styled after many modern blowback airsoft pistols, this means it functions very similarly to the real steel. It is a very hefty gun made almost entirely from metal and has a very snappy blowback action which adds to its shooting realism. Even the magazine looks and feels like a real 9mm magazine with similar weight and dimensions. The Cybergun Sig Sauer X-Five shoots very accurately for a BB airgun and has fairly decent power considering it's blowback function, this does result in heavy usage of CO2. I was able to get about 3 magazines out of a CO2 cartridge. This is one of my favorite airguns because it is so true to form and function.:

Buy this gun in Canada

Buy this gun in the US

Related Posts:

• TWO NEW AIRGUNS - UMAREX PPK/S AND UMAREX BERETTA ELITE II
• UMAREX WALTHER PPK/S BLOWBACK CO2 BB PISTOL REVIEW

This is a video I posted on YouTube a while back that has gotten a lot of views (Now Over 300,000). It's basically me and a friend shooting a couple of guns. The first set of guns (One in each hand - Tomb Raider Style) are two Walther CP99 Compacts made by Umarex. The CP99 Compact is a great little BB gun with a very fast and light trigger pull.

Next up is another Umarex product, a Walther PPK. This one is moded to fire Full Auto, making it one of the smallest Full Auto BB Guns. Too bad it's all over so fast! I'll look at doing some proper reviews of these fine Airguns down the road...

Buy this gun in Canada   -   Buy this gun in the US

Buy this gun in Canada   -   Buy this gun in the US