Power Sources Covered in this review: CO2 - Spring Piston - Variable Pump -HPA (High Pressure Air)
Pro’s:
CO2 Airguns allow for fast repeat shooting, great for action shooters, generally CO2 Airguns will supply a medium power range. No need to pump or cock your CO2 powered weapon in-between shots and a CO2 power source can allow for a very realistic action of the gun you are shooting.
Spring Piston Airguns are best suited of single shot situations, they can provide low to high power output depending on the spring used. Spring Piston Airguns are very low cost to operate since you only need to buy the Pellets or BB’s. Spring Piston Airguns are not greatly effected by outside temperatures.
Variable Pump Airguns allow you to decide how much power your gun will have and can offer very high power output depending on the Airgun. Variable Pump Airguns are very low cost to operate since you only need to buy the Pellets or BB’s. Variable Pump Airguns are not greatly effected by outside temperatures. Variable Pump Airguns generally have very low recoil and vibration.
HPA (High Pressure Air) Airguns generally do not require pumping or cocking in-between shots and some even come in semi automatic or bolt action. HPA Airguns can have very high power output and even be used on larger game using large caliber ammunition. HPA Air Rifles have lower recoil and low vibration. HPA Airguns can be charged ahead off time so they are ready for use when you need them.
Con’s:
CO2 Airguns require the additional cost to buy the CO2 as they do not function without it. CO2 Airguns have a limited power output and lose power as you shoot and use up the CO2. CO2 Airguns are effected by hot and cold temperatures and will have less power in colder temperatures and may not even work in super cold environments.
Spring Piston Airguns require cocking before each shot. Spring Piston Airguns can have a lot of recoil and vibration, so much so that special optics must be considered when buying an optical sight. The action of the spring recoil can effect accuracy, especially if you are not use to the vibration and recoil or have spent some time practicing using a Spring Piston Airgun.
Variable Pump Airguns will require multiple pumps to achieved maximum power output which can take some time in-between shots. So you are going to have to work for each shot.
HPA (High Pressure Air) Airguns require the use of a manual pump to fill their built in air tank to maximum pressure and it does take a lot of time to manual fill an HPA tank. Alternatively you can have the air tank filled at a shop or buy a pressurization system similar to a scuba tank out paintball setup, the cost of this setup can be very high but will save you the castle of manually pumping air in to your HPA Airgun. HPA Airguns are generally a little more bulky then other Airgun systems since they have to accommodate fairly large air pressure tanks.
Power: Generally speaking a longer barrel is going to allow for more power. If you compare most CO2 pellet pistols to CO2 Pellet Rifles, you will find that the CO2 Pellet Pistol will generally shoot about 300-400 fps using a standard lead Pellet. On the other hand many CO2 Pellet Rifles can get up to as high as 600 fps which is much better speed for humanly shooting some smaller pests.
If you are talking about Springer or Variable Pump Air Pistols versus their Air Rifle counterparts, again the Air rifles will generally shoot with much more power. I have seen some none CO2 Air Pistols shoot up into the 500-600 fps range but again compered to none CO2 Air Rifles, they can even double these numbers.
Some of you may ask about Steel BB Pistols and Rifles. I personally would never really sue this type of ammunition for pest control simply because most BB Rifles have much less raw power than Pellet Rifles and steel BB’s will not be as accurate at any type of longer distance.
Stability: When holding any rifle from the shoulder, you have three point of contact with your body spread out in a much longer distance than a two handed pistol grip. Holding steady even without a rested position is much easier using a rifle. Even when using a rested position, the rifle will more stable.
Accuracy: A big factor in accuracy is stability but there are also other factors to consider. Barrel length its self does not make the gun more accurate, you only need a few inches of barrel length to get constant accurate results from a gun. What makes longer barreled guns more accurate is the distance between the rear and front sight. The closer the sights are together, the more margin for error there is, the longer you spread out the sights from each other, the more accurate the sighting system becomes.
Overall More Humain: When you consider Air Rifles tend to have higher power, better accuracy and overall more consistency than shorter barreled Air Pistols. The logical choice for humanly shooting a Pest is to use the Air Rifle. The last thing you want to do is make any animal suffer, even if it has been causing a lot of havoc around your home or farm or place of business.
This is not to say that a “Real Gun” is not as good as an Airgun or better in other ways, in this video I’m just pointing out how an Airgun in some cases can actually be better suited than a Real Gun.
Availability: What I mean by this, is that in many countries Real Guns can be very hard to acquire and often require safety course and applications before one can purchase a Real Gun. I have no problem with this but it is a reality that must be considered. Having an Airgun versus not having a gun at all makes it a better option for people that live in countries that have strict gun laws. Here in Canada we are allowed Real Guns, even pistols but we do have restriction on our pistols and so I can only get certain guns in an Airgun version. As a collector this is better than not having the gun at all.
Price to Buy: Generally speaking you can pickup an enter level Airgun for much less money than a real gun.
Cost to Shoot: Real gun ammo prices have been steadily increasing to the point that a day out shooting can cost several hundred dollars just on the ammunition alone.
Comparison of Price:
50 rounds of 9mm ammo will cost around $18.00
6000 rounds of 4.5mm Steel BB will cost about $18.00
CO2 is a bit less than $1 per 12 gram Cylinder which can yield up to 100 shots each.
To shoot 100 rounds of 9mm will cost close to $40 versus 100 shots of 4.5mm steel BB at around $1.
For this reason alone an Airgun can make a lot of sense even for Real Gun owners looking to get more cost effective practice time.
Access to Shooting Locations: Depending on where you live you will have to consider your local laws and where you are allowed to shoot both types of guns but typically you can shoot an Airgun safely just about anywhere as long as you implement some backstop safety precautions. Here in Canada we can only shoot a pistol at designated gun ranges, where as Airguns have a lot more allowances to shot them as long as you are not braking any city bylaws.
Training Guns: Even if you plan to eventually step up to a Real Gun at some point, an airgun is a great option to first learn proper gun handling skills since if you where to make a mistake, the consequences are much less severe. Airguns are also a lot less intimidating than a real gun since they are much quieter and have less recoil, you don’t even need to wear ear protection with most Airguns which means an instructor can communicate to his pupil on the range a lot easier.
Prop Guns: Since Replica Airguns look so much like real guns these day, they can often be used as a safer substitute for use in Movie, TV or other Photo and Video productions. Using a Real Gun on set generally requires a certified “Gun Wrangler” be on hand as Real Guns must be transported, stored and handled using very strict regulations. Airguns generally do not need to follow the same rigid regulations that Real Guns are bound to.
Tactical Training with Live Targets: Obviously shooting a real gun at a live target would not fair well for anyone involved, so that is completely out of the question. Airsoft Airguns are however perfect for Tactical Training and other weapons based simulations. All that is required for safety when using Airsoft guns is the use of eye protection and generally some heavy clothing.
I am sure there are some more areas in which Airguns may have the advantage over a Real Gun but these are the main ones that I could think of.
I already made several review videos for both Gletcher NGT (4.5mm Steel BB) and the Gletcher NGT R (.177 Cal Pellet) Revolvers, including table top and shooting videos. So make sure to check those videos out for more information on both versions of Gletcher NGT and NGT R Revolvers.
I did however miss some noteworthy details that I wanted to cover in this video. Firstly, the real steal Nagant M1895 Revolver this Gletcher NGT is styled after has a very unique gas-sealing system that the Airgun version does not replicate or really require but it is worth mentioning.
Here is some more info on how the original Nagant M1895 Revolver Gas Seal System works:
(From Wikipedia) The M1895 by contrast, has a mechanism which, as the hammer is cocked, first turns the cylinder and then moves it forward, closing the gap between the cylinder and the barrel. The cartridge, also unique, plays an important part in sealing the gun to the escape of propellant gases. The bullet is deeply seated, entirely within the cartridge case, and the case is slightly reduced in diameter at its mouth. The barrel features a short conical section at its rear; this accepts the mouth of the cartridge, completing the gas seal. By sealing the gap, the velocity of the bullet is increased by 15 to 45 m/s (50 to 150 ft/s.) This feature also eliminates the possibility of injury through the dangerous expansion of gases from the cylinder behind the barrel, which are easily capable of severing a finger if the user holds the gun incorrectly (with a finger positioned in front of the cylinder during fire) - a noted safety-issue in conventional revolvers.
Moving on to some of the features incorporated into the Gletcher NGT NGT-R CO2 BB and Pellet Revolver that I did not point in any of my previous videos. There is an extractor rod that can be used to extract a shell, this is not really necessary on the airgun version since the shells do not expand and tighten on the cylinder as they would n the real steal Nagant M1895 Revolver built is nice that we can replicate this feature with the Airgun version. You can also remove the cylinder completely from both the BB and Pellet shooting Gletcher NGT NGT-R CO2 Revolvers. The cylinder is actually very heavy and adds a lot of weight to this compact 7 shot Revolver.
It is always nice when an Airgun is built in such a way that it replicates the real steal version as closely as possible and the Gletcher NGT NGT-R CO2 BB and Pellet Revolvers do this nearly perfectly.
I get asked on a daily bases form many of my Vimeo Viewers about how and if there is a way to get rid of the White lettering on Airguns, Typically people are wanting to remove the intrusive Warning instructions from Airguns like the Cybergun Tanfoglio Witness 1911, the Cybergun/Swiss Arms GSG 92/P92 and many other CO2 Replica Airguns that have lettering or branding that you may want to get rid of.
In this Instructional Tutorial Video I show you how can at least tone down the white lettering and even completely remove it on some Airguns without damaging the Airguns finish underneath the white lettering. You will have to use some patience and perhaps repeat this method a few times but the end result is worth the effort.
The magical product I use to remove the white lettering on many popular Airguns is a product from Birchwood Casey called the Presto Gun Blue Pen. This product is actually designed to touch up real steel gun in areas where the blueing has worn off, lucky for us the Birchwood Casey Presto Gun Blue Pen also works well to remove the ugly white lettering from Airguns.
I have often been asked which of the Shells for the Shell Loading Revolvers work in which Shell Loading Revolvers? After all many of them look a lot alike so can you mix and match Shells for the various types of Shell Loading Revolvers?
In this Vimeo Instructional Video I test out a bunch of Shells to see which ones actually will work or not work in several of the most popular Shell Loading Revolvers.
Some of the Shell Loading Revovers Tested in this Instructional Video are:
To make this as comparable a test as possible I used two KWC/Gletcher Makarov Full Blowback Pistols each with their own separate magazine, again one with a 12 gram CO2 and one using the ANT system.
HPA or High Presure Air is not effected by cold weather which makes this setup ideal for shooting in cold situations since fps is not effected at all. As CO2 requires heat to expand, the colder the outside temperature the less amount of expansion you get from the CO2 whihc results in less power, this is really noticeable on your follow-up magazines as the CO2, magazine and even the gun will have started to cool down from the CO2 exposure.
The ANT Advanced Novelty Tech FIRE CO2 HPA Conversion Kit even when using large 20 ounce CO2 tanks will help with the cool down effect since the large CO2 tanks will take much longer to cool down and even freeze up as compared to the smaller 12 gram CO2 which can get frosty even after the first magazine.
I did notice in this Field Test Shooting Review that the CO2 did pretty good as it was my first magazine and the temperature was not all that cold out. I can say the HPA System was shooting much harder, after making this video I popped off another couple magazine with each gun shooting out to at least 100 feet and the ANT FIRE HPA setup was really throwing the 4.5mm Steel BB's out there quickly. As expected the 12 gram CO2 mags really started to trail off especially on the third magazine of shots.
All in all, the ANT Advanced Novelty Tech FIRE CO2 HPA Conversion Kit will not only bring your cost per shot down significantly but it allows you to keep shooting with no down time waiting for your gun to warm back up and the ability to use HPA (High Pressure Air) means you will get even more fps performance out of your air guns but also much more consistent shot performance all day long!
Well ANT (Advanced Novelty Tech) made an update model that supports a bunch more guns, that's a good thing of course. This new model is called the "FIRE" and it supports the following guns. I did find however that ANT list that the Gletcher NGT and Webley Mark VI Revolvers where supported by the FIRE but my findings indicated the CO2 screw on both these guns had a smaller diameter so they where not compatible. Other than that small discrepancy most of the other guns on their list should work just fine.
What exactly is the ANT Advanced Novelty Tech FIRE CO2 HPA Conversion Kit?
The Advanced Novelty Tech FIRE CO2/HPA Conversion Kit is a remote line adapter for Airsoft, BB, and pellet guns. Compatible with over 60 guns, it is easy to install and converts a compatible gun for use with a Paintball remote line and CO2 or HPA tank. Eliminating the need for disposable CO2 cartridges, while still being interchangeable with disposable CO2 cartridges, it delivers a longer, more powerful, and more consistent shooting experience between refills.
So what is the ANT Advanced Novelty Tech FIRE CO2 HPA Conversion Kit going to do for you?
Eliminate the need for the more expensive disposable 12 gram CO2 cartridges.
Use interchangeably with disposable 12 gram CO2 cartridges.
Use in conjunction with a Paintball remote line with standard quick disconnect fittings and a CO2 or HPA tank. (recommended use up to 1000 psi)
Shoot thousands of rounds before needing to refill your CO2.
Fits compatible Airsoft, BB, and pellet gun CO2 pistols.
Easy drop-in installation.
Overall cost savings.
More consistent FPS especially when shooting fast or in full auto.
I have already made a Table Top Video Review for the Gletcher NGT Silver CO2 BB Revolver which for the most part is the same gun but in a 4.5mm Steel BB non rifled barrel version and as the title indicates with a different finish being the silver version. Other than finish and ammunition being used, both guns are virtually the same.
I always like getting outside and shooting the airguns I review even on these fall overcast days, at least the temperature was not too cold, right around 14 °C or 57.2 °F so decent for my testing purposes. The Gletcher NGT R like the BB shooting NGT is a fairly small air revolver and so pretty much anyone should be able to shoot this air revolver even if you have smaller hands, I did find that pre-cocking the hammer for single action shooting was a bit of a stretch when reaching over with the thumb, but you can just as easily shoot in double action, both trigger pulls are nice and light with the double action being a bit longer and heavier.
Loading the 7 round cylinder will take longer than your standard stick magazine BB pistol since you first need to pop some .177 caliber pellets into each shell, if you want to speed up the process you don't have to eject the shells to load them, you can simply index the cylinder and pop a pellet into each shell while still inside the cylinder.
In terms of fps performance, the Gletcher NGT R CO2 Pellet Revolver shot a little higher than expected getting a 4 shot average of 376 fps using 7 grain RWS Lead pellets, so around 50 fps higher than the claimed 328 fps on the box and even a bit higher than the steel BB version I tested earlier. This is really good considering the short barrel and fact that a revolver can leak a little CO2 between the cylinder and the barrel and even the cylinder and the CO2 valve.
I really felt comfortable using the rather old school fixed open post and notch sights, the grey/black finish on the Gletcher NGT R may be a bit hard to see on darker targets but shooting on my white target was no problem. My 7 shot grouping from 30 feet back using a semi rested shooting stance produced about a 1 inch grouping well centred vertically just a hair to the left so all in all the Gletcher NGT R CO2 Pellet Revolver has the power and accuracy I was hoping for even in such a small package.
It has been a while since I picked out some of my favorite guns, after all my favorite gun picks change on a daily basis since there are so many awesome guns out there to pick from.
This Vimeo video is a little different since I pick out my favorites from a bunch of mostly replica gun categories including Steel BB, Pellet, Airsoft, Revolvers and Blank Pistols.
You may notice most of my picks happen to be blowback guns but to me airguns are all about being as realistic as possible and having blowback operation to me help to simulate the realism that much more. The exception in this video is in the pellet gun category since I decided on a pellet gun that was more about function and purpose over being any type of real replica.
Hopefully you take the time to watch my entire Vimeo video since I also bring out some close runner ups but here is a list of my top picks on this day, tomorrow it could be a completely different list of guns ;)
This comparison Review Video serves a few purposes, first to compare the ASG Dan Wesson 715 Revolver 4.5mm steel BB version to the 6mm plastic Airsoft version in both velocity and accuracy. Secondly to give my new Chrony Chronograph with lighting kit a test to see if I can get more reliable readings in lower light and thirdly to try and redeem the Steel BB version of the Dan Wesson 715 as last time I tested it, it did not get all that high of fps readings, well below the claimed 430 on the box.
In this review video I test both Dan Wesson 715 Revolvers out, first with my Chrony Chronograph and then all in one take I setup and shoot 6 rounds each on separate paper targets from 30 feet back to see how accurate the smaller heavier Steel BB rounds are compared to the larger lighter Plastic BB's. I used 5.1 grain RWS 4.5mm Steel BB's and .20 gram 6mm plastic BB's and installed brand new 12 gram CO2 cartridges in both guns.
In terms of my Chrony consistency, the smaller steel BB's still struggled to get consistent readings with only 2 out of 6 shots while the larger Airsoft BB's managed to get a good reading 4 out of 6 shots. Steel BB velocity was right around 350 fps while the Airsoft BB's where travelling much faster at closer to 450 fps.
Both the Steel BB and Airsoft CO2 Dan Wesson 715 Revolvers shot 6 round grouping of about 2 inches with 4 out of the 6 shots making a much tighter 1 inch group again with both ammo types. The Airsoft Dan Wesson 715 seemed to be centered on target well while the Steel BB Dan Wesson 715 shot a bit low.
This Vimeo Video Preview covers three really nice CO2 Pistols recently added to our Replica Airguns Canada Store. One is a pellet pistol from Gletcher called the Gletcher NGT R which is for the most part the same as the standard 4.5mm Steel shooting NGT but the R model is made to shoot .177 caliber pellets so it also has a rifled barrel. I am expecting pretty decent accuracy with this pistol!
Last but perhaps the best or at least most anticipated gun I am showing off today is the Umarex S&W M&P40 Full Blowback CO2 BB Pistol. This is a really nice acurate replica of the real steal S&W M&P40 with full licensing and pretty much every part operational like it would be on the .40 caliber version.
Here are some basic Specifications for all of these fine Co2 Airguns...
This Field Test Shooting Video Review focuses on the performance results of the ASG Dan Wesson 715 CO2 BB Revolver. I put it through my standard Field Test to see what kind of feet per second performance it can achieve using 5.1 grain Steel 4.5mm BB's. I also perform my standard 6 shot Revolver accuracy test from 30 feet back with a semi rested shooting position to see how this very modern 6 shooter groups on a paper target.
In the first portion of the fps velocity test, I used my temperamental Chronograph shooting 6 rounds in total with a brand new CO2. Out of the 6 shots I did mange to get 3 good readings so I guess it could have been worse. The fps reading for the three shots where 338, 331 and 326 with a three shot average of 332 fps. Not what I expected from the ASG Dan Wesson 715 CO2 BB Revolver since the claimed fps is closer to 430 and it was not an overly cold day so I should have been in the ball park. Perhaps my Chrony is not reading like it should be and maybe it's time for a new one :(
Next on my Field Test Shooting list was the accuracy portion of this review. I performed my standard 30 foot back paper target shooting test using my standard semi-rested position, standing in the back with a sandbag up front to rest my hands on for stability. This position is fairly steady but not perfect so there is always some human factor to consider. I had to perform this part of the test twice as one of my cameras was not rolling in the first go around. Unfortunately the first test was the best but I can say the ASG Dan Wesson 715 CO2 BB Revolver is very capable of getting all 6 shots under 1 inch with a little practice and a steady hand
I really love the new ASG Dan Wesson 715 CO2 BB Revolver, it's for sure a much better made version than the older Dan Wesson and it seems ot be just as accurate. I am almost positive this pistol shoots harder than what my Chronograph was giving it credit for, you can just tell by how quick the BB's are getting to the target. so perhaps another FPS test is in order to find out for sure. Other than that the ASG Dan Wesson 715 CO2 BB Revolver is an awesome modern shell loading CO2 six shooter and a lot of fun to shoot.
This Field Test Shooting Video Review focuses on the performance results of the Umarex Colt Single Action Army CO2 Pellet Revolver. I put it through its paces to see what kind of feet per second performance it can achieve using .7 grain RWS lead pellets. I also perform my standard 6 shot Revolver accuracy test from a 30 foot back semi rested shooting position to see how this classic cowboy 6 shooter groups on a paper target.
In my first portion of the fps velocity test, I used my somewhat temperamental Chronograph shooting several RWS 7 grain lead pellets using a brand new CO2. I really did not have much luck with my Chronograph today, it did not seem to like the lead pellets I was using? I went through 12 shots and only got 3 decent readings which where rather spread apart. 318, 484 and 333 fps for an average of 378 fps. I can say that when shooting the Umarex Colt Single Action Army CO2 Pellet Revolver the pellets do seem to get to the target pretty quickly and my gut estimate is that they are moving somewhere in the high 300 to low 400 fps range.
Next on my Field Test Shooting list was the accuracy portion of this review where I did not have to worry about my tech gear working properly! I performed my standard 30 foot back paper target shooting test using a semi-rested position, standing in the back with a sandbag up front to rest my hands on for stability. This position is nice and steady but not perfect so there is always some human factor to consider and I know at least one of the 6 shots went a bit high on the account of me pulling that one shot just a little bit. Removing that one shot I kind of blew, I was able to get a very tight .75 inch grouping with the Umarex Colt Single Action Army CO2 Pellet Revolver. And looking back at the video my hold was a little on the jittery side, perhaps one too many espresso this morning...
I am a huge fan of these Umarex distributed Colt Single Action Army CO2 Pellet Revolvers, they now come in 4.5mm Steel BB, .177 caliber lead pellet and even Airsoft versions so you can take your pick depending on your intended use. If you want the best accuracy then definitely go for the pellet shooting version with its rifled barrel as you should be able to hit a quarter at 30 feet with it all day long.
This Field Test Shooting Video Review focuses on the performance aspects of the Umarex Brodax CO2 BB Revolver. I test it out to see what kind of velocity it can achieve as compared to the 375 fps Umarex states and I also conduct an accuracy test from 30 feet away to see how straight and true it shoots.
My first test, the velocity or fps test I performed using my Chronograph shooting five 5.1 grain standard zinc coated steel BB's. The fps ranged very little from 370 to 382 fps with an average 5 shot reading of 374 feet per second. Keep in mind the temperature was not exactly warm on this day, somewhere around 10 Degrees Celsius so I was not expecting top fps readings so getting pretty much exactly what Umarex claimed the Umarex Brodax CO2 BB Revolver would get makes me think there may even be more potential on a nice hot summer day.
Moving on to the accuracy or shooting portion of this field test review, I performed my usual 30 foot paper target test using a semi rested stance standing in the back with a sandbag up front to rest my hands on for stability. This position is fairly stable but not perfect so there is always some human factor to consider. For the most part the majority of my shots stayed within about a 1.5-2 inch grouping and stayed well centered on the target which is great considering the Umarex Brodax CO2 BB Revolver does not have adjustable sights.
A couple of side notes about the Umarex Brodax CO2 BB Revolver. I found the trigger to be really nice especially in single action with just about the perfect amount of take-up and trigger weight and a very predictable breaking point. In double action the trigger is also decent for a revolver, fairly short with a medium amount of pull, perfect for action shooting. I was only using the open non-adjustable sights but still got good results so I can only imagine how much better I could perform with the Umarex Brodax CO2 BB Revolver
Materials: Mostly plastic with some metal construction.
Weight: 1.3 pounds (586 grams).
Barrel: 5.5 inches, non-rifled.
Propulsion: 12 gram CO2.
Action: Revolver, single & double actions.
Ammunition Type: 4.5mm steel BB's.
Ammunition Capacity: 10 rounds.
FPS: 375.
Trigger Pull: The trigger pull on the Umarex Brodax CO2 BB Revolver is actually rather nice. If you decide to cock the hammer back and shoot it single action style then you get a little bit of that SAA Revolver like ratcheting sound. The trigger pull in single action mode is short with virtually no take-up and on the light side. Double action shooting with the Umarex Brodax CO2 BB Revolver is not overly long or heavy either so action shooting is totally possible with this BB shooting CO2 revolver.
Accuracy: I can not comment so far on the shooting performance for the Umarex Brodax CO2 BB Revolversince I have not shot it yet. The weather is getting nicer outside so that should happen pretty soon. The claimed FPS for the Umarex Brodax CO2 BB Revolver is stated at only 375 which I find seems a bit low for a none blowback fairly straight forward BB pistol with an almost 6 inch barrel so hopefully my testing shows performance up into the 400's which I am hoping for. The open sights are non adjustable but there are tons more options by taking advantage of the two rails top and bottom for adding either a red dot or laser to increased target shooting ability.
Build Quality: The Umarex Brodax CO2 BB Revolver is pretty much an all metal pistol with the outer shell being made up of plastic, there is a fair bit of internal metal going on along with the trigger, hammer and of course the inner barrel made out of metal parts. Mechanically the Umarex Brodax CO2 BB Revolver feels solid and even though it only weight in at 1.3 pounds it feels much heavier in the hand.
Realism: The Umarex Brodax CO2 BB Revolver as far as I know is not an exact replica of any real steal gun currently in production. It's basically a spin off of an ultra tactical .44 magnum revolver with a super beefed up front barrel assembly sporting all kinds of accessory option to be placed on the top and bottom rails. I like that Umarex made sure to recess the barrel opening so it has a more realistic barrel size. Like many new CO2 airguns coming out these days the CO2 is not only well hidden inside the grips but a handy Allen key is built into the handle.
Not the heaviest revolver on the market but it feels really nice in the hand and has good balance, the weight is not bad at all and feels heavier than 1.3 pounds.
Trigger action is really good in both single and double action, short light single action trigger and totally usable double action trigger.
CO2 is well hidden with built in Alan key in the handle.
Rails top and bottom for all kinds of accessory add on options.
Barrel is recessed for that larger caliber look.
Nice and discreet safety.
Comes with three 10 shot easy to load rotary magazines.
Low cost with high fun factor.
Cons:
Grips are a bit hard to remove to get at the CO2, may work-in over time?
All black sights are not great on dark backgrounds and are non adjustable.
Would have liked to see fps into the 400 range.
Comments:
The Umarex Brodax CO2 BB Revolver when I first picked it up did not appeal to me all that much, maybe knowing it was for the most part yet another mostly plastic BB revolver with those thin pop in disc magazines didn't help me take notice much. But as I have been playing around with the Umarex Brodax CO2 BB Revolver it has grown on me a lot. I think it has a really cool look that is also very usable in terms of putting juts about any accessory you want on this CO2 revolver. The hammer and trigger action are also both excellent for not juts an inexpensive Airgun but even a higher end airgun. And right out of the box, or should I say clam-shell plastic wrap, you get three rotary disc magazines which is a nice bonus.
My Vimeo Table Top Review for the Umarex Brodax CO2 BB Revolver:
Some more of my Personal airgun pistols for sale! I am showcasing here on the Replica Airguns website and over on the Replica Airguns YouTube channel a series of videos I am making for the purpose of selling some guns out of my personal collection. I simply have to make room for the new guns I will be testing and reviewing for everyone, my collection has gotten a little bit out of hand and needs to be thinned down a bit :)
In this 6th Mike's Personal Guns For Sale video, I am offering three of my Airsoft pistols, the super popular Dan Wesson 6 Inch Silver in pretty much brand new condition complete with the box, manual, speed loader and shells. I also have tow rather hard to get Airsoft guns that are in somewhat limited working condition and need a little TLC. But the simple fact that they are not easily obtained here in Canada does bring up their value a little bit.
Make sure to watch my above YouTube video to see these Airsoft Pistols I am selling and instructions on how you can take part in the sale and purchase of them. By the way I am only selling to Canadian residents since shipping cross borders is a little sketchy.
Here is a list of the Airsoft Pistols I am selling from my personal gun collection:
Yes, I have more of my personal guns for sale, now we are getting into the pistols! I am showcasing here on the Replica Airguns website and over on the Replica Airguns YouTube channel a series of videos I am making for the purpose of selling some guns out of my personal collection. I simply have to make room for the new guns I will be testing and reviewing for everyone, my collection has gotten a little bit out of hand and needs to be thinned down a bit :)
In this 5th Mike's Personal Guns For Sale video, I am offering some of my pellet pistols in a variety of models ranging from some classic Crosman SAA .22 caliber revolvers to more modern CO2 blowback pistols like the Umarex Beretta PX4 Storm
Make sure to watch my above YouTube video to see these Pellet Pistols I am selling and instructions on how you can take part in the sale and purchase of them. By the way I am only selling to Canadian residents since shipping cross borders is a little sketchy.
Here is a list of the Pellet Pistols I am selling from my personal gun collection:
Trigger Pull: The ASG Dan Wesson 357 Revolver has a smoother trigger than the previous non 715 Dan Wesson Revolvers. There seems to be less of that friction while the cylinder rotates past the spring engaged inner barrel. Even the Hammer has a nicer fell to it with less side to side wiggle. Single action is really nice with a very short take up and light release point.
Accuracy: I have not had a chance to test out the ASG Dan Wesson 715 6 Inch Silver CO2 BB Revolver so far since the outside whether has been rather cold and wet. In terms of accuracy I would expect at least a 1-2 inch grouping from 30 feet out and the clamed fps of 430 seems to be in line with what we should see from the 4.5mm BB shooting Dan Wesson 715. I guess we will have to find out later on when I do my Field Test Shooting video to be sure...
Build Quality: I thought the previous generation Dan Wesson Revolvers where built really nice but the new Dan Wesson 715 takes this up several notches higher. All you need to do is pick this gun up and immediately you are in a state of wow! You almost need to ask yourself if it is in fact the Real Steal Dan Wesson 715 357 Magnum Revolver it feels that good. ASG has beefed up the barrel assembly to a solid component that adds a lot of forward weight which would be just like what you would expect from the 357 Magnum shooting version. To balance it all off the forward weight, the grips section is also reinforced with metal underneath the Hogue Styled rubber finger grips which again are another huge improvement over the plastic pistol grips found on previous models of the ASG Dan Wesson's. The stainless finish is of course awesome and this guns simply looks and feels great!
Realism: Again referencing the new ASG Dan Wesson 715 6 Inch Silver CO2 BB Revolver to it's predecessors, the Dan Wesson 715 is a true replica of the Dan Wesson 715 357 Magnum Revolver in almost every aspect and not just the Dan Wesson name. I could tell you everything that was the same but it's simply much easier to point out the only real difference I was able to point out and that would be the two pins that connect the barrel assembly to the frame of the BB version of the Dan Wesson 715. Not a deal breaker by any means and the pins really don't take away from this gun in my opinion.
Another great shell loading revolver, perhaps one of the nicest modern BB revolvers to date!
Almost all metal design, super heavy, feels like a real gun in the hand.
Lots of detail in this gun, very well made, fit and finish is excellent.
Dan Wesson Licensed and an excellent replica overall.
Adjustable rear sight for windage and elevation.
Rubber Hogue style finger grips, huge improvement over previous Dan Wesson grips.
Well hidden CO2 screw and Allen key built into the removable grip.
Much improved hammer and trigger action, smoother trigger and less wiggle in hammer.
Barrel opening is very realistic, even has simulated rifling.
Safety design is well hidden and easy to use.
Cons:
Two pins to attach the barrel assembly to the frame are not in line with the real steel version.
Trigger still has a bit of that initial friction in double action mode because of the spring loaded internal barrel.
Comments:
I was already a big fan of the Dan Wesson line of Revolvers, this new 715 version of the Dan Wesson takes it to a whole new level! In terms of the modern shell loading CO2 Revolvers out there the ASG Dan Wesson 715 6 Inch Silver CO2 BB Revolver is by far my new favorite. ASG completely redesign their new ASG Dan Wesson 715 6 Inch Silver CO2 BB Revolver basing it entirely on the real steel version and capturing the quality, look and feel nearly exactly. if you already have a Dan Wesson Revolver and think that perhaps you can pass the new version by, well I would think again or you may be missing out on one of the best BB Revolvers out there at this time.
My Vimeo Video Table Top Review for the Dan Wesson 715 CO2 BB Revolver:
I am showcasing here on the Replica Airguns website and over on the Replica Airguns YouTube channel a series of videos I am making for the purpose of selling some guns out of my personal collection. I simply have no more room for the new guns and in some cases I either have duplicate guns or very similar versions so there is no need to have both. Some guns I am less attached to and as I already stated I need to make room for some of the new stuff I will be reviewing and or buying for myself.
In this third Mike's Personal Guns For Sale video I am offering four BB rifles, three of which have full auto or at least burst mode ability and the fourth BB rifles is more of a Shotguns with the ability to shoot three BB's at once. Most of these BB rifles are really hard to get here in Canada now since one is not made anymore and the two are simply not currently being imported into Canada.
Make sure to watch my above YouTube video to see these four BB rifles I am selling and instructions on how you can take part in the sale and purchase of them. By the way I am only selling to Canadian residents since shipping cross borders is a little sketchy.
Here is a list of the BB Rifles I am selling from my personal gun collection:
