Type: Pellet/BB Multi-pump Air Rifle.

Manufacturer:Crosman.

Model: MK-177.

Materials: Plastic with some metal.

Weight: 3.5 pounds.

Barrel: 16.75 inches, rifled.

Propulsion: Multi-pump.

Action: Single shot - bolt action with manual advance magazine.

Ammunition Type: .177 caliber pellets & 4.5mm steel BB's.

Ammunition Capacity: 5 shot pellet magazine - 18 shot BB internal BB magazine - 350 round BB hopper.

FPS: 750 with Pellets and 800 with BB's for the US version (Up to 495 with Canada version).

Trigger Pull: The trigger pull on the Crosman MK-177 is medium length and fairly light. The trigger mainly releases the bolt so no pre-cocking of the trigger is required. The trigger is plastic but seems to work just fine as there is no real load on the trigger when shooting, you do need to get used to where the release point since there is some take up well before the trigger releases.

Accuracy: I found the Crosman MK-177 Air Rifle to be a very good shooter, getting about a 1 inch 10 shot grouping from 30 feet out in a semi rested position (sand bag up front, standing in the back). I also put 3 rounds through my somewhat failing Chrony Chronograph using 3,5 & 10 pumps and the MK-177 with the maximum 10 pump shot as high as 631 fps using 6.9 grain RWS lead pellets. I would expect the Canadian detuned version to shoot well below the 500 fps Canada limit much like my Canadian Crosman M4-177 I reviewed a while back.

Build Quality: The Crosman MK-177 Multi-pump Air Rifle is mostly molded plastic, but for a $100-ish Military Styled Replica Air Rifle it hits the mark in terms of affordability and if it was an all metal airgun you would more than likely expect to double or tripple this price point! Even though plastic is used throughout this Air Rifle, there are some internal metal parts where they need to be, the fit and finish seems to be good and I do not get the feeling the Crosman MK-177 is cheaply made in any way. The fact that most parts are molded means there is very little that can snap or break off and will make this air rifle even more durable longterm.

Realism: The Crosman MK-177 is a lose replica or copy of an FN SCAR Assault Rifle or ACR. It is not exact in terms of true dimensions to accommodate the pumping mechanism, You will not find very many working parts as just about everything is molded into the plastic on this Crosman MK-177 rifle. Unlike the Crosman M4-177 the lower magazine area is not removable and the rear stock is also none adjustable, I am not sure why Crosman didn't add these features to the MK-177 like they did to the M4-177? I am glad to see another Replica Assault rifle on the market as so few of them are available in Pellet or steel BB shooters.

Available in the:Replica Airguns Store.

Pros:

• The only SCAR Pellet/BB rifle I know of?

• Fairly well priced.

• Excellent accuracy!

• Very easy to pump.

• None red dot version comes with detachable and adjustable iron sights.

• Rails on top and sides for accessories.

• Option of shooting pellets or BB's, I would stick to pellets and save the barrel since it is not semi auto.

• Feels super solid since there are very few moving parts that could break.

• Looks like the Crosman M4-177 Pellet magazines are compatible.

Cons:

• Mostly plastic and just about everything is molded into the gun.

• Bolt and magazine are on opposite sides?

• Would of been cool if Crosman made a dedicated BB magazine?

Comments:

The Crosman MK-177 Multi-Pump Pellet/BB Air Rifle is very much like it's brother the Crosman M4-177 with a few plusses and a few minuses when comparing the two of them together. On the plus side the MK-177 has a bit more power and also the pumping is much easier while yielding higher internal pressures. On the downside the Crosman MK-177 is almost entirely molded plastic with no removable lower magazine or adjustable stock, and the bolt has been switched around to what I feel is the wrong side since now you need to index the magazine on one side and work the bolt on the other requiring a less efficient approach. Either way it is nice to have another replica air rifle on the marker and for the relatively low price you get a nice accurate pellet rifle, great for target shooting and even small pest control.

Watch my Vimeo Full Video Review of the Crosman MK-177 Pellet/BB Air Rifle:

BuyAir Rifles in Canada 

Buy Air Rifles in the US

I wanted to cover some basic Airgun, Airsoft Gun, Blank Gun and Paintball Gun information on what do they all shoot, what makes them shoot and some other miscellaneous info thrown in along the way...

Your should also watch the video attached at the bottom of this post as it goes into a fair amount of detail.

Let's begin with the types of ammo used:

Airgun Ammo

• Airgun ammo for the most part is broken down into BBs and Pellets, the most standard size BB and Pellet is the 4.5mm or .177 caliber Steel BB and Lead Pellet. You can also get Pellets in other calibers and even other materials other than lead such as steel or aluminum, some can have plastic skirting around a metal interior.

• Pellets also come in a variety of caliber's like .177, .20. 22. 25 and even larger but then I would start considering them to be bullets as they will take on the shape of a bullet when they get into the larger sizes.

• Airgun Ammo is not be fired at people, it is primarily used for target and hunting small game.

• Airguns can use Spring Pistons, CO2, Compressed Air and Multi-pump propulsion systems.

Airsoft Gun Ammo

• Airsoft Guns for the most part shoot round 6mm (.22 caliber) plastic BBs which come in a variety of weights ranging from .12 grams up to .48 grams. There are larger Airsoft BBs such as 8mm and even larger.

• There are biodegradable and even tracer florescent Airsoft BBs available.

• Airsoft Ammo is traditionally used for Airsoft battles and can be fired at people using protective gear. Airsoft Ammo can also be used for target shooting.

• Airsoft Guns can use Spring Pistons, Spring Piston - AEG (Electric Motor) CO2, Gas (Green, Red, Propane) and Compressed Air propulsion systems.

Paintball Gun Ammo

• Paintball Guns or "Markers" have been historically used for the sport of Paintball but their whereabouts came from the need of ranchers and forestry workers to mark trees. Hence the name "Marker"

• Paintball ammo comes in a variety of sizes ranging with the most common being .43 and .68 caliber. They are generally made from a gelatin outer coating containing primarily polyethylene glycol, other non-toxic and water-soluble substances, and dye, they are usually biodegradable.

• Paintball Guns can also shoot a variety of Paintball Ammo that can be made out of Rubber, Plastic, Glass and they can also contain Powders and even Pepper for use in non lethal defense.

• Paintball Guns can generally use either CO2 or Compressed Air as their propellant.

Blank Gun Ammo

• Blank Guns are just like Real Guns but without the dangerous bullet at the end of the brass shell. Other than that they work exactly the same as a Real Gun!

• Blank Guns are used when a bullet is not required or even wanted. For instance... Gun safety, gun training, training animals to be around guns and/or loud noises, Props for Movies - Stage -  Film - TV, Collectors that do not want the red tape associated with owning a Real Gun or when owning a Real Gun is prohibited.

• Blank Guns can shoot a variety of sized ammo, most common are .22 caliber crimped, .380 crimped, 8mm P.A.K. and 9mm P.A.K.

• Blank Guns use gun powder as their means of operation.

Here are the most common forms of propulsion used in the guns we discussed earlier:

CO2

• CO2 is the most common propellant in Airguns (BB and Pellet), it is also used in Airsoft Guns and Paintball Guns.

• CO2 is a compressed gas which expands when released, it requires a warm environment to fully expand and tends to cool it's surroundings quickly when shot fast or in full automatic which can slow the velocity of the projectile and even freeze up the gun being used.

• The most common reusable CO2 cartridges are 12 and 88 gram but you can get larger CO2 tanks in a variety of sizes that can be refilled with CO2.

Gas

• Gas is used primarily in Airsoft Guns, I have not personally seen an Airgun that is made to use Gas other than CO2.

• Gas is similar to CO2 in that it is a compressed gas that expands when releases, it also cools down the gun it is being used in and requires a warm environment.

• Gas comes in a variety of names, Green Gas, Red Gas and Propane Gas. Green Gas contains Propane as it's base but has additives in it like silicone for lubrication .

• Red Gas is know to be a bit more powerful than Green Gas as it has Chlorodifluoromethane or HCFC-22, R22 or Freon 22 used in refrigeration which turns to a liquid under a slightly higher pressure giving you slightly higher fps.

• Many people use propane gas with an adapter that allows the mixture of silicone as propane is cheaper to buy.

Compressed Air (HPA)

• Compressed Air (HPA - High Pressure Air) is most commonly used in Airguns and Paintball Guns but some people use it for their Gas based Airsoft guns.

• The compressed air comes from high PSI tanks that can be purchased in a variety of sizes and contains compressed air at pressures up to 5000psi.

• These tanks are reusable and usually need to be refilled at a paintball or scuba shop, some people buy their own compressors or large scuba tanks for refilling purposes.

• Some Compressed Air (HPA) guns have their own built in tanks that can be filled with a compressor or even a manual pump.

• Compressed air does not cool down the gun it is being used in and is a great option for high output or fully automatic guns.

Multi-Pump Pneumatic

• Multi-Pump Pneumatic systems are most commonly used in Pellet and/or BB guns.

• Multi-Pump Pneumatic guns use the same principle as HPA - High Pressure Air guns in that they require pressurized air as the propellant. The main difference with Multi-Pump Pneumatic guns, is that you do all the work by pumping the gun between shots. Generally speaking you pump the gun 3-10 times, take a shot and repeat this process.

• Multi-Pump Pneumatic guns are not effected by air temperature and are great for target and small pest control.

Spring Piston

• Spring pistons are generally found in Pellet Rifles and Pistols but some Airsoft Guns also use a Spring Piston System and generally speaking Spring Piston Guns are single shot only or in other words, the Spring needs to be drawn back before each shot. Spring Piston Guns can have magazines that allow for quicker repeat shots.

• Spring Piston Guns come in many cocking configurations, Brake Barrel and Side lever to name a couple.

• The Spring can be a Mechanical Spring or a Gas Spring.

• Spring Piston Guns are not effected by temperature and are often used for small game hunting and target shooting.

Automatic Electric Guns (AEG)

• Automatic Electric Guns  are generally found in Airsoft Rifles but there are some Airsoft Pistols (AEP) that use this same system.

• Automatic Electric Guns use a similar system to a Spring Piston gun but have an electric motor that does all the work of drawing back the spring. You can even have fully automatic AEG guns.

• The power for the electric motor comes from removable batteries, so it is a combination a battery supplying the motor with the power to draw back the spring that creates a pillow of air that shoots the BB.

• AEG Airsoft Guns are great for situations when you require high capacity magazines with full auto capability. 

Gun Powder

• Gun powder is used in Blank Guns, in the same manor that it is used in a Real Gun, the charge from the Gun Powder supplies the force required to operate the blowback in most semi auto Blank Pistols, it also creates the sound of a live round along with the muzzle flash which makes Blank Guns great for training and as Props for Movies and Film.

• Because the kinetic energy from a blank gun is the same as a real gun, blank guns can be very dangerous when used in close proximity to an object, see my "Are Blank Guns Dangerous Video"!

Some other Gun Relevant Terminology:

Blowback

• Blowback operation is when some of the force of the propellant is used to move the slide backwards, which in most cases cocks the hammer for single action and can also pickup and chamber a round into the barrel.

• The slide spring supplies the energy for the return to the forward position of the slide.

• Blowback Guns do rob some power from the bullet force and in the case of CO2 or Gas Guns the also reduce the amount of shots per CO2 or Gas fill.

Revolver, Semi Automatic

• Revolver: Revolvers feed ammunition via the rotation of a cartridge-filled cylinder, in which each cartridge is contained in its own ignition chamber, and is sequentially brought into alignment with the weapon's barrel by a mechanism linked to the weapon's trigger (double-action) or its hammer (single-action)

• Semi Automatic:  semi-automatic pistols use the energy of one shot to reload the chamber for the next. Typically recoil energy from a fired round is mechanically harnessed. After a round is fired, the pistol will cycle, ejecting the spent casing and chambering a new round from the magazine, allowing another shot to take place immediately.

Single Shot, Repeater, Semi Automatic & Fully Automatic

• Single Shot: A Single Shot Gun needs to be reloaded each time it is shot.

• Repeater: Repeating action Guns are single barreled guns containing multiple rounds of ammunition. These rounds are loaded from a magazine by means of a manual or automatic mechanism, and the action that reloads the rifle also typically re-cocks the firing action. The term repeating rifle is most often applied to weapons in which the next cartridge is loaded by a manual action, as opposed to semi-automatic rifles, in which the force of one shot is used to load the next.

• Semi Automatic: A semi-automatic, or self-loading, firearm is a weapon that performs all steps necessary to prepare the weapon to fire again after firing.

• Fully Automatic: A Gun that uses either its recoil or a portion of the gas propelling the projectile to remove the spent cartridge (in the case of a gun-shell), fire again repeatedly, as long as the trigger is held down or until the magazine is exhausted. Automatic Guns are distinguished from semi-automatic Guns in their ability to fire more than one shot in succession once the trigger is pulled.

Single, Double Action, SA/DA

• Check out my post explaining Single and Double action!

• Single-Action (SA): trigger performs the single action of releasing the hammer or striker to discharge the firearm each time the trigger is pulled.

• Double-Action (DA): The trigger both cocks and releases the hammer or striker

• SA-DA:  A SA/DA firearm combines the features of both mechanisms. You can pull the trigger in Double Action when the hammer is down which cocks and releases the trigger or you can cock the hammer with your thumb and then release the trigger using Single Action to fire the weapon. 

Lever Action, Pump Action, Bolt Action

• Lever Action: In a classic lever-action firearm, rounds are individually loaded into a tubular magazine parallel to and below the barrel. A short bolt is held in place with an over center toggle action. Once closed, the over center action prevents opening solely by the force on the bolt when the weapon is fired. This toggle action is operated by a hand grip that forms part of the trigger guard. When operated, a spring in the tubular magazine pushes a fresh round into position. Returning the operating lever to the home position chambers the round and closes the breach.

• Pump Action: With a pump-action firearm, the action is operated by a movable fore-end that goes backwards and forwards to eject, extract, and chamber a round of ammunition. Pump-actions are usually associated with shotguns.

• Bolt Action: The bolt opens and closes the breech end of the barrel and contains the firing pin. The bolt is held in place with a lever that fits into a notch. Moving this lever out of the notch will release the restraint on the bolt, allowing it to be drawn back. An extractor removes the spent cartridge, which is then ejected through the lever slot. A spring at the bottom of the magazine pushes up the reserve rounds, positioning the topmost between the bolt and the chamber at the base of the barrel. Pushing the bolt lever forward chambers this round and pushing the lever into the notch locks the bolt and enables the trigger mechanism.

Magazine vs Clip

• Magazine: A magazine is an ammunition storage and feeding device within or attached to a repeating firearm. Magazines can be removable (detachable) or integral to the firearm. The magazine functions by moving the cartridges stored in the magazine into a position where they may be loaded into the chamber by the action of the firearm. The detachable magazine is often referred to as a clip, although this is technically inaccurate.

• Clip: A clip is a device that is used to store multiple rounds of ammunition together as a unit, ready for insertion into the magazine or cylinder of a firearm. This speeds up the process of loading and reloading the firearm as several rounds can be loaded at once, rather than one round being loaded at a time. The term "clip" is also frequently used to refer to a detachable magazine, though such usage is incorrect.

I managed to get my hands on a pair of brand new Kimar Lady K PPK 9mm P.A.K. Front Firing James Bond inspired Blank Pistols. One in Silver (Chrome) and the other in Matte Black. They come in plastic hard shell cases along with manuals and cleaning rods. They shoot in both single and double action and field strip just like the real Walther PPK.

To get in on the bidding, simply Email Me Here with your highest bid by no later than July 5th 2013 by midnight. At the conclusion of this Silent Auction I will notify the winner and they will have 24 hours to make payment before I move onto the next highest bidder.

This Rare Blank Gun Silent Auction is open to my Canada customers since we sell Kimar blank guns in the US Replica Airguns store, Canadian Customers will pay an additional $17.99 for Shipping/Handling plus their local provincial sales Tax. Good luck to everyone! 

• You can watch my earlier Kimar Lady K Review here.

Check out my video showing off these two Silent Auction Kimar Lady K Front Firing 9mm P.A.K. Blank Pistols:

Photo of WE G18C Removed by Request from Glock "Renzulli Law Firm"

All references, photos and video claiming that any item in this review/video looks like a Glock or is a Replica of a Glock in any way shape or form have been removed from this post as requested by Glock"Renzulli Law Firm"

Type: Airsoft GBB Pistol.
Manufacturer: WE.
Model: G18C.
Materials: Metal & plastic.
Weight: 1.7 pounds (776 Grams).
Barrel: 4.5 inches, smooth bore.
Propulsion: (GBB) Gas Blowback.
Action: Semi & full auto.
Ammunition Type: Airsoft 6mm Plastic BB's.
Ammunition Capacity: 25 rounds.
FPS: Up-to 380 with longer barrel attached.
Trigger Pull: The trigger pull on the WE G18C is very nice and light since the blowback action does most of the work pre-cocking the action. There is a built in and working trigger safety like you would find on a real steel NAME REMOVED with about a quarter inch of take-up leading to a very light and crisp release.

Photo of WE G18C Removed by Request from Glock "Renzulli Law Firm" 

Accuracy: Out of the Box the WE G18C shot great rather well for me when I did my pretest from the 20 foot mark, I found the WE G18C was dialed in pretty decent and shot very close to the bulls eye, maybe a hair to the left which is good since the sights are non adjustable. I shot a very respectable 5 shot 1.5 inch group in semi auto which opened up a great deal when I shot the remaining 15 rounds but at least they all seemed to stay pretty much on the paper which is not bad considering how much this gun jumps around in full auto.

Photo of WE G18C Removed by Request from Glock "Renzulli Law Firm" 

Build Quality: The WE G18C Airsoft seems to be well made, and you will find lots of metal parts where they need to be, again similar as what you would find in a real NAME REMOVED. Fit and finish is nice but I did have an issue with the gas tube when I first got mine, it broke rendering the gun inoperable, a quick swap out with a new gas tube and all is well and so far after a number of magazine worth of shots the WE G18C is still working well and the new gas tube is holding up.

Photo of WE G18C Removed by Request from Glock "Renzulli Law Firm" 

Realism: WE has taken some liberty with the markings on their WE G 18C copy, they are similar to what you would find on a real NAME REMOVED but not actually the same, as longs as you don't look too closely you will most likely be fooled into believing it's a licensed NAME REMOVED! As for how the WE G18C is built and how it operates, you will find it's a dead ringer to a real steel NAME RMOVED and even breaks down exactly the same.
Reviewed by: Replica Airguns. 

Photo of WE G18C Removed by Request from Glock "Renzulli Law Firm"

Pros:

• It's a NAME REMOVED Replica!
• Lots of metal in this gun similar to a real NAME REMOVED.
• Kind of licensed similar to a NAME REMOVED.
• Semi auto & full auto selectable :)
• Very solid blowback kick.
• Field strips just like a NAME REMOVED.
• Very good accuracy and power even with the shorter barrel installed
• Comes with two barrels, one for use with the suppressor to increase fps for Canadian import. 

Photo of WE G18C Removed by Request from Glock "Renzulli Law Firm"

Cons:

• No real sight adjustments.
• Had a problem with the Gas Tube cracking almost right out of the box. 

Photo of WE G18C Removed by Request from Glock "Renzulli Law Firm"

Comments:
I have heard many people say they love WE products and then there are some that claim they are not all that well made! Other than my issue with the cracked gas tube, my WE G18C is holding up well and is working nicely, I think some earlier WE products lacked some refinement which may have led to problems but from what I have heard as of late, WE has stepped things up and is making a better product these days. My WE AK74UN is a testament to this as it is built like a tank and has tons of real stamped steel all throughout. Getting back to the WE G18C Airsoft GBB, it's really fun to shoot with it's amazing blowback and for a GBB pistol it shoots pretty hard and finds the target with easy. 

Photo of WE G18C Removed by Request from Glock "Renzulli Law Firm"

My YouTube Video of the WE G18C Gas Blowback Airsoft Pistol:

Buy Airsoft gun in the Canada Store  -  Buy Airsoft gun in the US Store

• Checkout my Table Top Review for the Umarex Walther P99 CO2 Blowback Airsoft Pistol:

The Umarex Walther P99 CO2 Blowback Airsoft Pistol is a fairly low cost Airsoft BB pistol but even so, there is no reason why we should expect less than stellar performance from it.

I have already done a pretest for the Umarex Walther P99 CO2 Blowback Airsoft Pistol while making my Table Top Review and it shot right around the 333 fps mark, but it was a colder day then. I also shot my Umarex Walther P99 DAO from a much closer 20 foot distance for the pretest and got a respectable 2 inch grouping.

On the actual Field Test Shooting day it was much warmer (tank top weather ;) and so as would be expected, this time my Umarex Walther Airsoft P99 shot a bit quicker at right around a 356 fps average, shooting 10 rounds through my Chronograph. I would expect to get even more fps on an even hotter day as it was only about 22 degrees Celsius or about 72 Fahrenheit on this test day.

Accuracy from 30 feet out was pretty close to my pretest 20 foot testing if you exclude the two flyers but again the Umarex Airsoft P99 version was shooting a bit to the left which unfortunately can not be adjusted other than changing my sight position on the target. I would think the trend to the left will only increase as we shoot further out but this gun is really best suited for close quarters shooting anyways and should have no problems right up to 50 feet shooting a man sized target..

You can expect to get around 100 shots or a good 6 full 15 shot magazines from Umarex Walther P99 CO2 Blowback Airsoft Pistol which should get you nicely through a CQB match without having to change CO2 cartridges. For being a rather low cost Airsoft gun, it did perform well enough for me on this day, keep in mind it does have a firm long pull double action only trigger so really fast shooting will take it's toll on your trigger finger ;)

Watch my Field Test Shooting Video for the Umarex Walther P99 CO2 Blowback Airsoft Pistol:

Buy this Airsoft Pistol in Canada  -  Buy this Airsoft Pistol in the US

• Checkout my Table Top Review for the ASG Dan Wesson 6 Inch Silver CO2 Airsoft Revolver:

I've had the opportunity to review and shoot my Dan Wesson 4.5mm Steel BB Version so I kind of knew what to expect with the Airsoft version, much of the same but with perhaps a little bit less accurate further out shooting since the plastic BB's will tend to drift a bit more.

I already did my pretest for the ASG Dan Wesson 6 Inch Silver CO2 Airsoft Revolver while making my Table Top Review and shot right around the 400 fps mark, but it was a colder day then, I also shot my ASG Dan Wesson Airsoft Revolver from a closer up 20 feet for the pretest and got a nice tight 1.5 inch shot group.

On the actual Field Test Shooting day it was much warmer (tank top weather ;) and so as would be expected, this time my ASG Dan Wesson 6 Inch Silver CO2 Airsoft Revolver shot a bit faster at closer to a 420 fps average with 6 shots put through it. There is even room for some more fps still as it was only about 22 degrees Celsius or about 72 Fahrenheit on the test day.

Accuracy from 30 feet out was not as tight as my pretest 20 foot testing and I would imagine this will spread out even more the further back we go with the Airsoft ASG Dan Wesson, as is the case with Airsoft BB's. Airsoft BB's are just not as accurate as steel BB's especially when shooting at longer ranges. I would expect this Airsoft Dan Wesson version should still be very effective on a "man sized target" up to about 60 feet or so. Keep in mind there is no hop-up in this revolver so teh Airsoft BB's will drop much more than a gun that has hop-up.

Like the 4.5mm BB shooting version you can expect a good 100 or more shots from this Airsoft BB Shooting Dan Wesson CO2 Revolver. Having tradition revolver single and double action makes for both precise and action styled shooting. All in all a really nice Airsoft pistol from ASG.

Watch my Field Test Shooting Video for the ASG Dan Wesson 6 Inch Silver CO2 Airsoft Revolver:

Buy ASG Airsoft Pistols in Canada  -  Buy ASG Airsoft Pistols in the US

I have a couple of guns I wanted to share with you all and no we do not sell them at this point in time and I can not say if we will or not down the road.

There is just no way we can carry every brand of gun and every gun from every brand, that said I still sometimes have my eye on a gun and will pick it up even if I have to pay full retail juts so I can add it to my collection and also do a review for all of you.

Photo of WE G18C Removed by Request from Glock "Renzulli Law Firm" 

Today I showcase two Gas Blowback Airsoft guns from WE. I have been wanting to get an AK variant of some sort since there was a big whole in my collection after the RCMP came into my house and took my scary AK BB gun away. And if for some reason you feel this "again" legally imported through the CBSA non convertible airgun is in some way a concern, please feel free to come on over and have a good look, no SWAT team necessary this time. I am just around the corner from the police station and I make a good cup of coffee!

Getting back to this update, the other WE Airsoft gun is the WE G18C which like the WE AK74UN, also has semi and full auto select-ability. Both guns have excellent blowback kick with the AK74UN having a full travel blot which kicks like a mule and has a slower full auto cycle rate much like a real AK47.

Both guns have metal parts where you would find them on the real steel versions while the AK even goes so far to have actual stamped steel all over just like you would find on an AK.

Photo of WE G18C Removed by Request from Glock "Renzulli Law Firm"

I will be doing full reviews for both these WE GBB Airsoft guns so stay posted for those video reviews, in the meantime you can watch my Update Video showcasing both these WE Airsoft guns.

Buy Airsoft gun in the Canada Store  -  Buy Airsoft gun in the US Store

• Checkout my Field Test Review for the Umarex Walther P99 CO2 Blowback Airsoft Pistol:

Type: Airsoft Pistol.

Manufacturer: Umarex.

Model: Walther P99 DAO

Materials: Metal & Polymer.

Weight: 1.5 pounds.

Barrel: 4 inches, metal non-rifled.

Propulsion: 12 gram CO2.

Action: Semi auto, double action only with blowback.

Ammunition Type: 6mm plastic Airsoft BB's.

Ammunition Capacity: 15 round stick magazine.

FPS: 380.

Trigger Pull: The Double Action Only trigger pull on the Umarex Walther P99 CO2 Blowback Airsoft Pistol is long but not overly heavy for a double action trigger, it does have a break point mid way where it locks partway back, I presume this is the point in which a BB is loaded from the magazine into the barrel? The rest of the pull is still medium but much shorter with a distinct release point.

Accuracy: I did do a quick preliminary test before I made this table top review to get an idea of where this gun performs in terms of FPS and accuracy, I shot 5 rounds through my Chronograph on a fresh CO2 and got an average of 333FPS which was a bit lower than the claimed 380 but it was not the hottest of days. I also stepped back 20 feet and from a semi rested position I was able to get 9 shots within 2 inches of each other which was not bad for a DAO gun that I have never shot before. I did shoot a bit down and to the left with the set sights.

Build Quality: The Umarex Walther P99 is well built for its rather low price tag, it may not have all the bells and whistles but it does get the job done with good fit and finish and materials used. You will find a plastic/polymer frame but there is a lot of metal where it would normally be found on the real steel version like in the slide, magazine, trigger, slide catch, magazine release, inner barrel and many other internal parts. No real complaints here!

Realism: The Umarex Walther P99 CO2 Blowback Airsoft Pistol is pretty close in looks to a real steel Walther P99 with the exception of a missing decocker, but I'm pretty sure this is the same with the real steel DAO version? There is also the funny looking safety on the right side of the frame found on many Umarex airguns. I have to mention the red tip but again this can be removed and even when removed the barrel it is still recessed which adds to the realism. The Blowback action, Walther licensing and nice heavy weight all add up to make this Airsoft pistol look and feel the part.

Purchase it from: The Replica Airguns Store

Pros:

• Low cost for a very believable and solid replica.

• All metal stick magazine.

• Metal slide and internal parts gives it decent weight.

• Rail for accessories.

• Well hidden CO2 screw.

• Walther licensing.

• Recessed inner barrel.

• White dot sights, easy to use.

• Right amount of power for indoor CQB style airsoft games.

Cons:

• Comes with a red tip even in Canada.

• Double action only, so trigger is a bit heavier.

• Kind of funny safety, not like the real gun.

• Blowback was a bit sluggish.

Comments:

Overall the Umarex Walther P99 CO2 Blowback Airsoft Pistol is a very good buy, it's a decent replica of the real steel Walther P99 with blowback operation, lots of metal parts, good fit and finish, decent performance and full Walther licensing and trademarks. All at a very affordable price tag. It may lack some of the extras you will find on more expensive and more functional Airsoft pistols but the simplicity of the Umarex Walther P99 CO2 Blowback Airsoft Pistol means it will most likely be a bit more reliable with less to go wrong down the road. If you have been looking for a nice Walther styled replica in an Airsoft version this may be just be the ticket!

My Vimeo Video Review for the Umarex Walther P99 CO2 Blowback Airsoft Pistol:

Buy the Umarex P99 CO2 Pistol in Canada 

Buy the Umarex P99 CO2 Pistol in the US

• Also checkout my Table Top Review for the Umarex - KWA MP7 Blowback Airsoft PDW:

The rainy weather let up today so I grabbed up my Umarex - KWA MP7 Blowback Airsoft PDW and put it through its paces today. I was a bit surprised that my groupings from 30 feet away shooting from a semi-rested position where a bit spread out, mostly top to bottom. Perhaps the hop up was effecting the MP7? The good news is that shooting in full auto did not seem to make things any worse :) I was using .25 gram BB's for the accuracy test.

As for the Chronograph portion of this field test shooting review, the Umarex - KWA MP7 Blowback Airsoft Machine Pistol shot a bit higher than claimed at just over 400 fps using .20 gram BB's with Propane Gas. I had no problems shooting a full magazine of 40 rounds with a full gas fill up and the cycle rate stayed nice and high with very little cool down effect.

I really enjoyed shooting the Umarex - KWA MP7 Blowback Airsoft PDW, it has a nice sound with just the right amount of blowback to give it a good feel without throwing off the sights, the trigger was very light and responsive and I ended up preferring to use the pop up sights over the pistol sights as I was shooting mostly with the stock and fore grip open. Those Cans never had a chance!

All in all the Umarex - KWA MP7 Blowback Airsoft PDW is one of the coolest compact and ultra modern Airsoft guns I have had the pleasure to review and test out.

Watch my Field Test Shooting Vimeo Video for the Umarex - KWA MP7 Blowback Airsoft PDW:

Buy this Airsoft Machine Pistol in Canada  -  Buy this Airsoft Machine Pistol in the US

• Also checkout my Field Test Review for the Umarex - KWA MP7 Blowback Airsoft PDW:

Type: Airsoft Machine Pistol (PDW).

Manufacturer:Umarex - KWA.

Model: H&K MP7 A1.

Materials: Metal & plastic.

Weight: 4 pounds, 7 ounces (2130 grams).

Barrel: 6.3 inches, smooth bore.

Propulsion: GBB - Gas Blowback.

Action: Semi-full auto selectable SAO.

Ammunition Type: Airsoft 6mm Plastic BB's.

Ammunition Capacity: 40 rounds.

FPS: 370.

Trigger Pull: The trigger pull on the Umarex - KWA H&K MP7 A1 is single action only as the charging handle has to be pulled back to open and release the bolt for the first shot fired. There is a trigger safety that must be engaged to fire, but it is not noticeable when shooting this Airsoft PDW. There is a short take-up and then a nice light release and short reset.

Accuracy: I was able to get decent accuracy in both semi auto and full auto burst with my H&K MP7 due to the mild to medium blowback. I would say I shot somewhere in the 2-3 spread with my 10 shot grouping from 20 feet out. When I do my full Field Test Shooting Review I will take it back a bit further and shoot form 30 feet out. I did get a bit higher then claimed fps right up into the 400 fps range when testing the Umarex - KWA H&K MP7 A1 on my Chronograph.

Build Quality: The Umarex - KWA H&K MP7 A1 Airsoft PDW is built extremely well, using near exact components that you would find on the real HK MP7, yes it has a plastic or polymer shell but that is what you would find on the 4.6mm x 30 real steel version. The Umarex MP7 Airsoft PDW does use lots of metal where it needs to be like in the internal housing, pins, bolt, barrel, rails and even the magazine. The fit and finish is bang on, this gun is as solid as they come!

Realism: I have to say the Umarex - KWA H&K MP7 A1 is pretty much a bang on copy of the real steel H&K MP7. The only telltale sign is the Umarex branding and warning label on the right side receiver, even the 6mm caliber markings are near impossible to make out on the underside right beside the serial number plate. Of course the red flash hider is a big "red flag" that takes away form the realism but for us here in Canada, a bit of red paint is all that is needed to fix that problem. just be aware that the flash hider is really glued on tight so plan that project accordingly!

Available at the: Canada Replica Airguns Store, US Replica Airguns Store

Pros:

• Excellent attention to detail with lots of working parts.

• Full H&K licensing and markings.

• Good overall 400 fps power for a short barreled gas blowback gun.

• Very nice trigger with working trigger safety.

• Lots of metal parts where they need to be and would be on the real K&H MP7 PDW.

• Semi auto & full auto selectable.

• High capacity GBB magazine (40 rounds)

• Sights are fully adjustable and offer two positions.

• Built in for-grip and rear slide-out stock

• Easy access to hop up system.

Cons:

• Came with the orange tip, you may want to  paint it. (hard to get off as it is glued on!)

• May be too powerful for CQB skirmishes without some detuning.

Comments:

I really like the Umarex - KWA H&K MP7 A1 Airsoft PDW, it's my kind of Airsoft gun! I love the modern look, I love the features and the price is also really good for what you are getting here, a GBB gun that is super versatile and can be used in close our out at range. The build quality is what impressed me the most, this Airsoft gun is super solid, that combined with the attention to every detail would fool just about anyone that it's not the real deal until a very close inspection is done:) The Umarex - KWA H&K MP7 A1 reminds me of the other ASG MP9 KWA built PDW I reviewed earlier, they are like two peas in a pod but both with their own unique personalities.

Buy this Airsoft Rifle in Canada
Buy this Airsoft Rifle in the US

I managed to acquire another Russian made Nickel Baikal MP-654K CO2 BB Pistol, the last one that came my way was back in September of 2012 and I am really surprised I got my hands on another one to be honest so if you missed out on the last one, now is your chance!

This 2004 Baikal Makarov Nickel MP-654K BB Pistol is in brand new condition and comes with the original box, manual, tools and o-rings. I have test fired it and it works great and holds CO2 with no leaks.

If you want the background info I encourage you to checkout the review videos I have already made for my own person exact version of this gun right down to the same production year:

• Baikal (IZH) MP-654K Makarov Replica BB Gun Review
• Baikal Makarov MP-654K 4.5mm CO2 BB Pistol Comparison

To get in on the bidding, simply Email Me Here with your highest bid by no later than May 31st 2013 by midnight. At the conclusion of this Silent Auction I will notify the winner and they will have 24 hours to make payment before I move onto the next highest bidder.

This Rare Airgun Silent Auction is open to both my Canada and US customers, Canadian Customers will pay an additional $17.99 for Shipping/Handling plus their local provincial sales Tax. US Customers will pay $29.99 International Canada to US Shipping & Handling but will not pay any sales tax. Good luck to everyone!

Enjoy my YouTube Video showing off this gorgeous Airgun and below that are some additional photos:

Here is a quick Update video of three Airsoft guns, two of which I have touched upon before but have not gotten around to doing any actual Table Top or Field Test Shooting videos for you (The ASG Dan Wesson Airsoft Revolver and the Umarex P99 Blowback Airsoft Pistol). I also show you a new Umarex Airsoft Gas Blowback PDW, the H&K MP7 A1, a very realistic version I am sure will be of interest to many of my Airsoft fans.

I will be doing proper Table Top and Field Test Videos for each of these Airsoft guns as soon as I can get to them all, starting with the Umarex Gas Blowback H&K MP7 A1 Airsoft PDW so stay posted for these upcoming video reviews...

Buy ASG Airsoft Pistols in Canada  -  Buy ASG Airsoft Pistols in the US

Buy this Airsoft Pistol in Canada  -  Buy this Airsoft Pistol in the US

Buy this Airsoft Machine Pistol in Canada  -  Buy this Airsoft Machine Pistol in the US

• Also watch my Tabel Top Review for the B&W Dragunova SVD Airsoft Sniper Rifle:

I had a chance today to get out and shoot my B&W Dragunova SVD Airsoft Sniper Rifle, the weather held out just long enough for me to setup my target a good 90-100 feet out in the field but as luck would have it, it started to rain on my camera gear right as I started doing my target shooting test using .36 gram Airsoft BB's. So in a bit of a rush, I shot off a good 10 rounds and was able to put most of them on the paper which from 100 feet out using an Airsoft rifle on a target the size of a standard 8x11 sheet of paper is not too bad at all, and don't forget I was just using the iron sights.

I found I didn't even need to use the hight adjustment on my rear sight as the hop-up seemed to keep the Airsoft BB's floating nicely on plane all the way to at least 100 feet. By the way if you watched my earlier Table Top Reviews I mentioned the B&W Dragunova SVD was shooting a bit to the left even after full windage adjustment to the right, well I managed to sort this out and pull the sight the little bit extra I needed to get it pretty much dead center.

Moving on to the Chronograph portion of this Field Test Shooting Review, I got the same results as my pretest with an average fps of 498 using .20 gram Airsoft BB's and an average fps of 277 using the heavier .36 gram BB's. I have heard that the B&W Dragunova SVD Airsoft Sniper Rifle can be a bit of a chore to cock but for me it was actually pretty easy and using a left overhand approach worked well, allowing me to cock the charging handle pretty easy while keeping my finger on the trigger and the rifle in position ready for my next shot.

The iron sights and the trigger setup seem to both work very well with this rifle, I really have no real complaints and really enjoyed shooting the B&W Dragunova SVD Airsoft Sniper Rifle. If the rain hadn't been coming down on my camera gear I may have put a bunch more shots into the target for the simple reason I was having so much fun :)

Watch my Field Test Shooting YouTube Video for the B&W Dragunova SVD Airsoft Sniper Rifle:

Buy the B&W Dragunova SVD in the Canada Store  -  Buy Airsoft Rifles in the US Store

I finally got out to shoot my Wyoming Arms Parker 10mm S.S. and it worked pretty well for me, the kick was hard but the design of this 10mm pistol helps reduce recoil so the recoil was not really all that much more than shooting a .45 or .40 caliber. If you have not watched my Wyoming Arms Parker 10mm S.S. Pistol Real Steel Overview then make sure to do so... I did have a few of my reload rounds that seemed to give me a bit of trouble but other than that the Wyoming Arms shot very well for me and was extremely accurate.

I also got the chance to shooting my Norinco Type 54 Model 213 9mm Tokarev copy, another nice gun to shot but even though it was only a 9mm it felt pretty jumpy, perhaps due to it's much smaller size and weight. Again you can also check out my Norinco Tokarev Type 54 Model 213 9mm Pistol Overview for more information on this one.

I also brought along my little ISSC M22 .22LR shooting Glock look-a-like to keep some of my shooting costs down since the 10mm are so expensive I needed to recoup some of my costs shooting the super affordable .22LR ammo. And yes I have a full Table Top Review for the ISSC M22 so check that one out if you're in the market for a fairly low cost .22LR that looks a lot like a Glock.

I had a great time and we got to shot some other guns while we where at the gun range; Walther P38 9mm, Glock 22 .40 Caliber, Sig Sauer Mosquito .22LR and the Smith & Wesson M&P 15-22 .22LR in all.

• Watch my Field Test Shooting Review for the B&W Dragunova SVD.

Type: Airsoft Rifle.

Manufacturer:B&W Airsoft (AIM TOP).

Model: SVD Dragunova.

Materials: Metal & plastic.

Weight: 6 pounds, 4 ounces (2.85kg).

Barrel: 23 inches, smooth bore.

Propulsion: Spring.

Action: Charging handle single shot.

Ammunition Type: Airsoft 6mm Plastic BB's.

Ammunition Capacity: 40 rounds.

FPS: Up-to 500.

Trigger Pull: The trigger pull on the B&W Dragunova SVD Airsoft Sniper Rifle is good overall, just a bit of initial take-up and then a medium trigger pull to release the heavy spring. You will of course nee to pull the charging handle with each shot to preload the spring.

Accuracy: My initial accuracy testing was done from about 45-50 out using .36 gram Airsoft BB's, it was a fairly windy day but  even so I was able to get a nice tight 2 inch grouping using a semi rested position. I also put the Dragunova SVD through my Chronograph testing and shot both the lighter .20 gram and heavier .36 gram BB's to see what kind of fps I would get using both weights. The lighter .20 gram BB's got right around 500 fps while the heavier .36 gram BB's shot a bit lower at approximately 380 fps. I did however find that sighting the SVD in for windage adjustments (left and right) was a bit of a challenge as you can only adjust the front sight by loosening it with an allen key and make only very slight left to right adjustments. I was not able to get the SVD to shoot far enough to the right using this method so I amy need to do figure something else out, perhaps a scope setup?

Build Quality: The B&W Dragunova SVD Airsoft Sniper Rifle is not a super expensive rifle but still has a good combination of metal and plastic components. Most of the parts that you would find on the real SVD are metal including the barrel, bolt/charging handle & receiver, trigger, magazine, sights, strap rings and rial system. The stock is of course plastic with some added rubber. The B&W Dragunova SVD is not overly heavy but still has a reasonable amount of weight to make it believable. Performance was very good with no mechanical problems other than the last two BB's in each magazine do not load into the rifle.

Realism: I have never held an actual Dragunova SVD in my hands but from what I have seen in photos, it looks to be a good copy of the real steel Russian sniper rifle. Lots of metal helps pull of the realism, a working charging handle, removable bolt cover, and lots of other working components make for a believable looking and functioning version of this Airsoft BB shooting Dragunova SVD Sniper Rifle.

Available in the: Canada Replica Airguns Store.

Pros:

• Lots of metal parts throughout where they would be on the real SVD.
• Good power and accuracy combination.
• Fairly high capacity magazine at 40 rounds.
• Sights are adjustable for elevation front and back and a bit for windage.
• Bolt is surprisingly easy enough to cock with either left or right hand.
• Lots of upgrades available for this sniper rifle.
• Inexpensive way to own a piece of history.

Cons:

• Some discrepancies in the manual (180 fps and 100 round magazine)
• Sighting for windage may not be adequate?
• Would definitely be much nicer with the wood stocks.
• Two BB's always pop out of the magazine area when empty.

Comments:

I found the B&W Dragunova SVD Airsoft Sniper Rifle to be a lot of fun to shoot, I was not sure how the charging handle system was going to work in terms of weight and easy of use to pull it back. I ended up using my left hand and reaching across and over and surprisingly this was very efficient and effective in charging the spring and allowed me to keep my righthand in place and on the trigger for very quick follow up shots. Power was as much as you would want from a sniper rifle and accuracy was also very good even in windy conditions. The only real problems I had where the two BB's that did not load from each magazine and the windage adjustments not quite allowing me to move my aim point enough for a bullseye at 50 feet out. I would recommend this B&W Dragunova SVD Airsoft Sniper Rifle and would suggest possibly adding some wood stocks and a magnified scope setup.

 Buy Airsoft Rifles in the Canada Store

Buy Airsoft Rifles in the US Store

After many many requests to show how the Umarex Walther PPK CO2 Tab Modification is done I have relented to public demand. I don't actually cut my tab in this PPK CO2 Tab Modification Video but I do go step-by-step in detail and compare my modified Umarex PPK to my unmodified Umarex PPK. It is really very basic on how this is done and only a hack say and perhaps a file are all that is required to make the modifications to the PPK CO2 tab in order to make it flush with the bottom of the handle area.

Your best bet is to simply watch my YouTube Video located below and follow the steps there but here it is in text form:

1. Place an empty (already pierced) CO2 into your Umarex Walther PPK and tighten the unmodified CO2 tab until fully tightened, just like you would tighten a fresh CO2.

2. Take note at how many threads are exposed between the bottom of the handle and the top of the plastic CO2 tab, there should be about 2-4 threads exposed.

3. Unscrew the CO2 tab all the way, place the PPK BB Pistol so it is secure (in a vice of some sort) and use a hacksaw or dremel to shorten the CO2 screw just above the plastic tab at the thread location you previously noted. Be conservative as you can always cut or file the screw a bit shorter if your first cut was not short enough.

4. Now use the same hacksaw or dremel to cut a notch in the exposed cut area of the CO2 screw so that you can use a slot screwdriver to tighten the CO2 screw.

5. That's it - Enjoy your modified Umarex Walther PPK CO2 BB Pistol!

Watch my Vimeo Video of the Umarex Walther PPK CO2 Tab Modification Tutorial:

Buy the PPK/S in Canada   -   Buy the PPK/S in the US

Every once in a while something goes wrong and your favorite BB shooter stops working as it should :( One of the most common problems I see with many of the full blowback BB and Airsoft pistols are BB's getting stuck in the gas tube. This is because this style of gun loads a BB into the breach area of the barrel every time you rack the slide forward. Of course this is only when there are BB's in the magazine.

The semi auto style of these guns is similar to that of a real gun, the blowback operates the slide which in turn moves back and then forward and loads a BB into the chamber. With a real gun, if you where to rack the slide manually again without shooting it, the chambered round would be ejected by the extractor but with a BB gun there is no extractor because there is no spent shell to eject. So multiple BB's can be loaded into the chamber area of the barrel overloading it and if the BB's have nowhere to go they just jam up and often go back into the gas tube which can cause all kinds of problems...

In this Cybergun KWC Tanfoglio Witness 1911 Stuck BB Removal Tutorial Video, I show you how to remove a BB or even multiple BB's from the gas tube area which in short requires; the removal of the slide and guid rod and spring so that you can push the gas tube forward and shake the BB out of the front of the gas tube.

Watch my Vimeo Video on how to remove a stuck BB from the Gas Tube on my Tanfoglio Witness 1911.

Buy KWC/Cybergun 1911 BB in Canada   -   Buy KWC/Cybergun 1911 BB in the US

Testing out the ASG - Marushin CZ 75 Blowback Shell Ejecting Airsoft Pistol was not an easy one but I did manage to get thorough it! First there was the setup, I could not shoot the ASG Shell Ejecting CZ 75 Airsoft pistol on my deck or I would have fore sure lost most of my shell casings for it. So I decided to setup camp in my pool area where I have a nice large flat area off to one side, I put down a ginormous tarp in hopes to catch the radically flying shells but even this failsafe did not catch them all as I later found out ;)

As with most of my Field Test Shooting videos, I usually do a bit of a pre test to make sure the gun is functioning properly and so I shot a full magazine of my brass shells through the ASG CZ 75 and it worked like a charm, of course when I started recording the live video it decided not to work at all and I still do not know why? I was able to revert back to the plastic shell casing that came with my ASG CZ 75 Blowback Shell Ejecting Airsoft Pistol and they seemed to be working so I went with them for my testing. Interestingly enough the brass shells got much higher fps (around 300+) when I did my pretest compared to around the 250 average fps I was getting with the plastic shell casings.

Shooting on target proved to be better than I though once I raised my sight point up a bit, the gun likes to shoot a bit low but once I found the sweet spot I got three rounds within about 3/4 of an inch from just over 20 feet away in a semi rested position.

I would not recommend this Airsoft gun as an everyday shooter and there is no way you could use it in any type of Airsoft simulation as the ejected shell casings would get lost for sure and the cost to shoot the ASG CZ 75 would get very high indeed! It would be good for use in a movie or video where you wanted the realistic look of shells being ejected and did not want to use a blank gun or render the shells in post. And of course it is just really cool to have an Airsoft gun that has ejecting shells :)

Make sure to watch my Table Top Video Review for information and photos on the ASG CZ 75.

Watch my Vimeo video of the ASG CZ 75 Blowback Shell Ejecting Airsoft Pistol in action:

Buy KJWORKS KP-09 Airsoft Pistol in Canada   -   Buy Airsoft Pistols in the US

Type: Shell Ejecting 6mm Plastic BB Airsoft Pistols.

Manufacturer:ASG.

Model: CZ 75

Materials: Plastic slide & frame, some metal parts.

Weight: 1.4 pounds (616 grams).

Barrel: Metalnon-rifled smooth bore.

Propulsion: Propane, green gas.

Action: Blowback, single action only.

Ammunition Type: 6mm plastic Airsoft BB's.

Ammunition Capacity: 8 rounds.

FPS: 279+ fps.

Trigger Pull: The trigger pull on the ASG CZ 75 Shell Ejecting Airsoft Replica is single action only, unlike the real steel version that actually has a single and double action trigger. The single action trigger has a light to medium pull but does have a fair bit of take-up to it.

Accuracy: I did not pre-test the ASG CZ 75 as the shells fly everywhere and you really need to be able to retrieve them afterwards as the cost to replace the shell casing is rather high. I do plan to do a full Shooting Field Test where I will shoot the ASG Shell Ejecting CZ 75 through the chronograph, place some shots on a target and also capture the action of this pistol in slow motion with a high speed camera. So stay posted for that. I can say that from the few shots taken in my house, that it seems to shoot pretty hard and the shells really com flying out of this gun with force, I also noticed that a BB does have to be loaded into each shell for there to be enough back pressure to allow for a full slide blowback and ejection of each shell.

Click here to watch my Field Test Video Review for the ASG CZ 75 Shell Ejecting Airsoft Pistol.

Build Quality: Even though this gun is made mostly out of plastic and from what I can tell is also made in Taiwan, it has a very good overall fit and finish. The slide slop is next to none and the licensing and markings look great. There are metal parts where they really need to be like in the barrel, hammer, trigger, safety, slide catch, magazine and a few other internal parts.

Realism: The ASG Shell Ejecting CZ 75 Airsoft Pistol is one of the most ultra realistic Airsoft pistols I have seen and mimics a real steel gun right down to the shells being ejected, how cool is that! If it had more metal then that would really top it off. Even with the plastic slide and frame it is very realistic in almost every way and even field strips just like a real CZ 75 and is fully licensed. The only feature not true to the actual CZ 75 would be the single action only trigger.

Purchased from YouTuber: FuzzyDicePimp

Pros:

• Very cool blowback with ejecting shell cases.
• Excellent fit and finish - tolerances are very good.
• Very believable working replica of the real steel CZ 75.
• Fully licensed.
• Fully field strip-able.
• Nice heavy full size drop out metal magazine helps give it some needed weight.
• Has metal parts where they need to be.

Cons:

• Plastic slide and frame.
• A bit low in the FPS department.
• Only 8 rounds in the magazine.
• Can not really use in the field, would lose too many shells.

Comments:

The ASG CZ 75 Shell Ejecting Blowback Airsoft Pistol is a very unique Airsoft gun, not very many Airsoft guns actually have ejecting shells. Just because of that I had to have it! Overall it is a pretty decent gun but I have yet to really test it out and that is the biggest shortcoming with this gun, you can't just shoot it anywhere as you need to shoot it in a place where you can recover your spent shell casings, unless of course you have all the money and shell cases in the world... That said it has a lot going for it other than the ejecting shells; Fully licensed and trademarked, blowback operation, full size drop out metal magazine and it's fully field strippable. I am sorry to say we don't offer it in out Canada or USReplica Airguns Store but we do have a similar all metal CZ 75 Airsoft offering in the form of the KJWorks KP-09 which I have done both a Table Top and Shooting Review for.

Buy KJWORKS KP-09 Airsoft Pistol in Canada

Buy Airsoft Pistols in the US

• Watch the Wyoming Arms Parker 10mm S.S. Performing at the gun range.

I do get requests from many of my viewers to do some real steel reviews and so far I have pretty much stuck with 22LR real steel reviews and my Tokarev real steel review. I recently purchased an interesting 10mm semi auto handgun used at a local used gun show and so I though I would share this rather interesting and no longer in production pistol with you. The handgun we are looking at today is the Wyoming Arms Parker 10mm S.S. At first place it looks a lot like a 1911 but it is different in several ways. the obvious traits are the safety on the slide and lack of a grip safety, it also has a very different looking handle and there are some internal differences also.

What drew me to the Wyoming Arms Parker 10mm S.S. was it's 1911 looks, the very nice stainless steel finish and the rather unusual 10mm ammo it was chambered to shoot. If your not familiar with the 10mm round it was developed by the FBI for sue by their field agents but was later determined to be a bit too much to handle for some of their smaller but later agents. The 10mm was then detuned and turned into the S&W 40 caliber which is essentially a shorter less powerful version of the 10mm.

Here are a bunch more photos that really show off the beauty of this pistol!

Definitely make sure to watch this video as I go through the gun and show you around, I also do a field strip and talk a bit more about the Miami Shootout that was the FBI's reason to look into the development of the 10mm Auto round.

Buy Airguns in the Canada Store

Buy Airguns in the US Store