Trigger Pull: The trigger pull on the Cybergun Sig Sauer P226 Airsoft Replica is good in both single and double action. Once the slide is pulled back and released the first round is chambered and the hammer will remain back placing the P226 in single action mode, the pull is light and the take-up is fairly short, most of your shots will be in single action mode unless you use the de-cocker to lower the hammer for a subsequent double action next shot, double action shots are still pretty light but much longer in order to cock the hammer.
Accuracy: Shooting the Cybergun Sig P226 from 20 feet out in semi rested position I was able to get very good results. I placed 10 rounds in about 1.5 inches with the shot placement being a bit low possibly due to my barrel mod, adjusting the hop-up may bring the aim point back up to where it should be. The Sig Sauer P226 Airsoft Replica shot right around the 316 fps range while conducting my 5 shot average chrony testing which was lower than advertised but I was using much heavier .20 gram BB's. You can expect to get a full magazine worth of shots out of each gas fill-up but I did notice that as the magazine got colder it did tend to become much less efficient and also seemed to vent a lot of vapor.
Build Quality: The build quality is generally good and I was surprised at the finish on this model as the paint is not showing any wear marks so far, the fit is good with minimal slide and barrel wobble and everything is working very well with no problems so far with a fair amount of shots through it, guess you could say I like shooting this gun :) Most of the gun is metal with only the grips and a couple internal parts being plastic.
Realism: The Cybergun Sig Sauer P226 6mm Airsoft pistol is a replica of the real steel Sig Sauer P226 right down to the licensing and it really is a great looking and functioning Airsoft Replica. You can field strip this gun exactly like a real Sig and all the mechanical parts work just the same including a working de-cocker and adjustable front sight.
Seemed to shoot a bit low for me, could adjust with hop-up a bit?
Only one magazine per Gas fill.
Comments:
I am a big Sig Sauer fan so it would take a lot for me to not give this gun a good review, with that said it performed pretty well, sure it was not the most powerful but I was using gas over CO2 so I was not expecting too much, it also shot a bit low for me but again that may have been because of the barrel mod so who really knows for sure at this point ;) And yes it came with that unsightly orange tip that I took short work of removing. At teh end of the day I still love it and it performed well without letting me down, just like a would expect from a real Sig Sauer!
My Vimeo Table Top Review of the Cybergun Sig Sauer P226 GBB Blowback Airsoft Pistol:
Trigger Pull: The trigger pull on the RG-88 and RG-59 in single action is very light with the RG-59 having virtually no take up at all while the RG-88 has some take up but then a noticeable and predictable release point. Both guns have medium to heavy yet smooth double action triggers.
Accuracy: NA.
Build Quality: The overall build quality for the ROHM RG-88 and RG-59 blank guns is excellent, being German made they are built to last and the fit and finish is very good. There are steel parts where they need to be like in the barrel, pins, screws and reenforcing parts, the rest of the gun is generally made out of a zinc metal with only the grips being plastic.
Realism: The ROHM RG-88 and ROHM RG-59 are not exact replicas of any given guns in production as this would make importing them into Canada even more difficult, but they do share similarities with some real guns in production. The RG-88 semi auto looks to be based around a Walther PPK design while the RG-59 has that Smith & Wesson Snub Nosed Revolver look to it. As for looking like and working like real guns, they do this very well, with the exception of the dangerous bullet coming out of the barrel!
German made quality, materials fit and finish is all excellent.
Almost all metal with some reenforced steel parts.
Nice light single action triggers on both guns with double action ability wehn needed.
Both are front firing with semi plugged barrels.
Come with flare adaptors and cleaning rods.
Seem to be some of the only blank guns we can get here in Canada right now.
Cons:
Not actual exact replicas of any specific guns in production.
The RG-59 only works with the .380 crimped, 9mm P.A.K. balnks are a bit too long.
Expensive due to them being harder to get and in high demand in Canada.
Comments:
As with pretty much all blank guns, they are mostly for show so it all comes down to how do they look and do they go bang when they are supposed to! In both cases they get top marks. Both the RG-88 semi auto and RG-59 revolver feel solid and the mechanical parts are tight and smooth giving a confident feeling when holding them. I like the larger caliber blanks over the .22 crimped blanks as they have a bigger bang but they will set you back in the cost department a bit more as the price for 9mm P.A.K. and .380 blanks will be a lot more than .22 crimped so keep this in mind when choosing a blank gun. If you're looking for a well made and dependable blank pistol then you really can not go wrong with any of the ROHM blank guns we sell in the Canada Replica Airguns Store.
My Vimeo Full Video Review for the ROHM RG-88 and RG59 Blank Pistols:
I usually do my Table Top Video Review first but this time around I did my Field Test Video Review first since I was all setup checking out a couple other guns at the time. When I do my detailed Table Top Video Review for the Cybgergun Sig Suer P226, I'll post the link here so stay tuned. If you have not already checked out my Barrel Mod Video for this same gun then check that video out where I remover the extended orange portion of the metal barrel and make the barrel flush with the end of the slide which is how the real steel version was originally made.
Getting back to the Cybergun Sig Sauer P226 GBB blowback Airsoft Pistol field test, as per usual I test this Airsoft semi auto gas blowback pistol on the Chronograph to see what kind of real world velocity I get and since I had some Green Gas on hand, I used it for this part of the review and got an average of 315 fps with a six shot string.
I also stepped back 20 feet and shot 10 times at my stationary target using a semi rested position (sand bag up front and kneeling in the back). Even though the Sig Sauer P226 shot a bit low I did get about a 1.25 inch group with the exception of one flyer that hooked down just a bit making the 10 shot group a bit wider at just under 2 inches. The low shot placement may have been caused by my barrel mod but since I did not do a before and after test, I can not say for sure?
Make sure to watch my YouTube Video of this Field Test as it also includes some nice slow-motion of the slide blowback at both 400 and 1200 frames per second.
Watch my full Video Field Test Shooting Vimeo Video below:
My 5 shot Chronograph test resulted in a lower than expected 308 average fps while my accuracy test shot from 20 feet out in a semi rested position this time received a just over 2 inch group but with most shots being within 1 inch, I have found with Airsoft guns that there can be some floaters perhaps due to inconsistencies with some of the ammo. In terms of shot placement the KJWORKS KP-05 HI-CAPA 1911 shot very well centered only being just slightly high and to the left but only marginally. I was also able to get 2 full magazines plus another half mag this time around so just over 60 shots with the KP-05.
KJWorks KP-05 1911 HI-CAPA Airsoft Pistol although not shooting as hard as I though it would still performed great for me and would make a great field gun as it performs very well and has a nice high capacity magazine which would come in handy in the heat of battle.
My 5 shot Chronograph test resulted in a very respectable 366 average fps while my accuracy test shot from 20 feet out in a semi rested position this time around came in a bit higher than my pre test right at around 2 inches. Several of the shots hit right on top of each other. In terms of shot placement the KJWorks KP-09 CZ 75 shot fairly well centered but just a bit high and a tad to the left. I was also able to again get 3 full magazines or around 75 shots out of this heavy blowback Airsoft pistol.
KJWorks KP-09 CZ 75 Airsoft Pistol really has a lot going for it, it's a great Replica of a real steel CZ 75 with a very nice single action trigger, it has great snappy full blowback with excellent fps and accuracy and it even gets a solid 75 shots out of a single CO2 which is very good for this style of full blowback gun.
I have not done my official Table Top and Shooting Reviews for the Gas Blowback Airsoft Cybergun Sig Sauer P226 but I really wanted to cut off the ugly orange painted barrel tip, it was kind of driving me crazy! keep in mind here in Canada we are not required to have orange tips on our Airsoft guns, most of the all metal or all black Airsoft guns imported these days fall into the "airgun uncontrolled firearms" category. If you live in the US or other parts of the world you could be breaking the law if you do this mod so be warned...
Your best best is to simply watch my Vimeo Video as I show you exactly how I removed the orange painted portion of the metal barrel using a hack saw, file, vice and some sand paper. All in all it was not too difficult and only took about 15 minutes to complete...
Trigger Pull: The trigger pull on the KJWORKS KP-05 is what you would expect from a true 1911 single action only trigger, it has very little take up with a smooth crisp and light release to it.
Accuracy: I shot the KJWORKS KP-05 from 20 feet out in semi rested position and got very good test results. I was able to place 10 rounds in under 1.5 inches and getting four shots right in the bullseye making the shot placement very good even without adjusting the sights (which can be adjusted for windage). The KJWORKS HP-05 1911 styled HI-CAPA Airsoft Replica shot right around 300 fps range while conducting my 5 shot average chrony testing which was surprisingly low for the CO2 magazine version, this may have been a temperature or CO2 related condition, when I conduct my full Field Test Shooting Review, I will review this and see if we can do better? I also got two full 30 round magazines worth of shots which is what you would expect from this style of full heavy blowback airsoft pistol.
Build Quality: I am extremely impressed with the build quality of all the KJWORKS Airsoft guns so far, the fit and finish is the best around on any of my guns including my 4.5mm steel BB shooters. After shooting several magazines worth of BB's, areas that are painted like the metal friction areas show very light wear which is rarely the case with metal built blowback airguns. Again the tolerances between the moving parts like the slide and frame are very tight showing excellent workmanship and machining from KJWORKS.
Realism: The KJWORKS KP-05 6mm Airsoft pistol is a replica of a High Capacity styled tactical 1911 45 Auto and is a great looking and functioning replica. You will not find any actual licensing on this pistol and the CO2 magazine does stick out a bit to accommodate the 12 gram CO2 but other than that this Airsoft pistol looks and works near exactly like a real 1911 tactical semi auto and is fully field strip-able. I really like the updated more tactical add ons like the tactical rail, machined trigger and hammer, white dot adjustable sights, wrap around grips and ambidextrous safety.
All metal pistol with good overall realistic weight to it.
Full heavy blowback operation.
Typical KJWORKS excellent fit and finish.
High capacity magazine 30 rounds.
Very good accuracy and well centered on target.
Nice replica of a High Capacity Tactical 1911 styled pistol.
I like the stainless highlights and ambidextrous safety and Rail for accessories.
Fully field strip-able.
Cons:
Shot a bit low Feet Per Second for me - should do better?
CO2 magazine is long to accommodate the 12 gram CO2.
Slide is heavy enough but seems to be a bit sluggish which is kind of a 1911 trademark so that can be taken as good or bad.
Comments:
The KJWORKS KP-05 1911HI-CAPA is another excellent full blowback Airsoft pistol from KJWORKS. The HP-05 is a classic upgraded more modernized version of the 1911 semi auto pistol which is a great foundation to build any pistol from. I found the CO2 usage to be decent on the KP-05 but felt that I should have been able to get more fps out of this pistol, I will be testing the KJWORKS KP-05 again and hope to see some better results in this area. With that aside, the KP-05 1911 HI-CAPA is a great shooter and as is, with its high capacity magazine would be a perfect sidearm for any Airsoft related squirmish or even just for honing up your shooting skills when getting to the gun range is not an option.
Trigger Pull: The trigger pull on the KJWORKS KP-09 CZ 75 Airsoft Replica is surprisingly light in single action but incredibly sticky at first in double action, with that said you really will not be shooting very often in double action unless you happen to de-cock the gun for some reason, at least you have the ability to shoot with the hammer down in double action when required. In signal action it took me a bit to get used to the very light trigger pull as I was letting some shots go off early.
Accuracy: I shot the KJWORKS KP-09 from 20 feet out in semi rested position and got very satisfactory results. I was able to place 10 rounds under 2 inches almost getting a 1 inch group with the exception of one flyer. Shot placement was also well centered but just a bit high which could easily be corrected by adjusting my aim point just a bit down. The KJWORKS CZ 75 Airsoft Replica shot right around the 360 fps range while conducting my 5 shot average chrony testing which is right where this gun is supposed to be. I also got three full 24 round magazines worth of shots with a bit of CO2 left over for a partial mag, so this gun can easily get 75 shots out of a 12 gram CO2 - not bad at all for this style of full heavy blowback airsoft design.
Build Quality: I am extremely impressed with the build quality of pretty much all the KJWORKS Airsoft guns, the fit and finish is the best I have seen on any of my guns including my 4.5mm steel BB shooters. Even after shooting several magazines worth of BB's, the painted metal friction areas show very light wear which is not always the case with metal built blowback airguns. (there was some wear present within the ejection port but this is common even with real steel guns as metal on metal will wear down the finish). The tolerances between the moving parts like the slide and frame are very tight showing excellent workmanship and machining.
Realism: The KJWORKS KP-09 6mm Airsoft pistol is a replica of the real steel CZ 75 and is a great looking and functioning copy. You will not find actual licensing on this version and the CO2 magazine does stick out a bit to accommodate the 12 gram CO2 but other than that this Airsoft pistol looks and works near exactly like the real mccoy and is full field strip-able. Even the safety operates just the same with safety available on half cock and full cock only.
All metal pistol with good overall realistic weight to it.
Very crisp and firm full blowback operation.
Excellent fit and finish - best I have seen.
Excellent fps and CO2 efficiency (three plus full 24 round magazines)
Good accuracy and well centered on target.
Very believable working replica of the real steel CZ 75.
Fully field strip-able.
Cons:
Does not have official CZ 75 licensing.
CO2 magazine is long to accommodate the 12 gram CO2.
Did get some finish wear in the ejection port area.
Comments:
The KP-09 CZ 75 is another wonderful full blowback Airsoft pistol from KJWORKS. The CZ 75 is a classic semi auto pistol and deserves the attention to detail the KJWORKS version demonstrates. I found the CO2 usage to be very good on the KP-09 considering the rather high 360+ fps I was abel to get with it. Top this off with high marks in the accuracy department and you have a real winner here. So if you're looking for a quality Airsoft Replica of the classic CZ 75 that shoots straight and hard and looks and operates just like the real steel version then the KJWORKS KP-09 should just do the trick for you.
Here is my official Field Test Shooting Video Review for my Umarex Walther P38 CO2 Blowback BB Pistol. As with my original Table Top Review, I shot pretty close to the manufacturers claimed 400 fps getting a 5 shot average of 392 fps.
And the same can be said with my accuracy pre test, both tests came in just about the same with an approximate 2 inch very well centered grouping shooting at the target from 20 feet out in a semi rested position. I even got 8 of the 10 rounds right in the 1.5 inch bullseye with only two rounds coming just outside. Good thing it was already pre sighted as the sight on the Umarex Walther P38 can not be adjusted. You can also expect to get a good 100 shots from a single CO2. I would also like to point out that even thought he slide is fairly light and the blowback is not full, The P38 still has a nice blowback snap to it.
The only real negative point I can make about the Umarex Walther P38 Replica Air Pistol is the somewhat medium to heavy trigger pull which I found a bit surprising since it has a single action only trigger? This was offset by the fact that The Umarex P38 had such good combined accuracy, power and CO2 efficiency wrapped up in a very believable Walther P38 Replica.
Here is my official Field Test Shooting Video Review for my KWC M1911 Model A1 TAC CO2 Blowback BB Pistol. Interestingly enough, this time around I got a bit lower average feet per second rating from this air gun at right around 290 fps as compared to the pre-test I did during my Table Top Review (shot closer to 310 average fps)? Both days the temperature was about the same and the CO2 used on both occasions was the same brand and where unused. Just goes to show you that these guns sometimes have a mind of their own...
At least the accuracy portion came in just about the same with an approximate 2 inch grouping shooting at the target from 20 feet out in a semi rested position. I did shoot a bit to the left and a bit low which I could adjust from left to right but since there is only a windage adjustment I would have to sight a bit up to hit the bullseye with the KWC M1911 Model A1 TAC. This time around I also got 4 magazine worth of shots as I slowed things down a bit and took my time and juts like last time I had no problems or malfunctions with my KWC M1911 Model A1 TAC.
The best part about shooting the KWC M1911 Model A1 TAC CO2 Air Pistol is it's beautiful single action 1911 styled trigger and nice heavy full blowback action, making this gun a great economical trainer if you own the real steel version or perhaps just want to feel like you do!
Here's a heads up on some new items we will be adding to the Canada Replica Airguns Store very soon so keep checking back if you're interested in them!
Your best bet is to Watch My Vimeo Video as I go over them all and show you around the new products, but for now here is some basic info on each item:
Trigger Pull: The trigger pull on the Umarex Walther P38 CO2 Blowback BB Replica is a bit heavier than I expected it would be as it is a single action only trigger. There is a lot of take up initially but once you hit the release area, the release point is what I would describe as a medium to heavy pull for a single action shooter. With that said it did not seem to effect the accuracy at all and I was able to rifle off quick shots fairly easily.
Accuracy: I shot the Umarex Walther P38 BB Pistol at a target from 20 feet away in a semi rested position, and it performed very good getting just under a 2 inch grouping and very well centered on the target. The sights are not adjustable so adjusting the Umarex Walther P38 would not be possible except by using a modified aim point! My initial Chrony testing puts this BB shooter just under the 400 claimed fps range right in the 380 area which is not bad considering the rather cold day I was shooting on. I also managed to get five magazines worth of shots which is a vert respectable 100 shots per CO2.
Build Quality: The Umarex Walther P38 CO2 Blowback BB Pistol is almost all metal with the exception of the grips which is great to see! I found the fit and finish to also be very good with a nice Semi Gloss paint job that should wear well over time. Interestingly enough the Umarex Walther P38 has a removable barrel so I am assuming that perhaps Umarex will introduce some more barrel length options at some point?
Realism: The Umarex Walther P38 CO2 Blowback BB Airgun is very close to the real steel Walther P38 and even has the Walther P38 licensing on it. What I was really impressed with was the fact that all the mechanical parts do exactly what they would do on the real gun. On some other guns these parts are merely for show and moulded into the gun. The Blowback action, hidden CO2 screw and recessed barrel all help to make this Walther P38 Replica very believable!
Replicates the real steel version fairly well with all the working parts pretty much doing what they did on the original.
Nice that it has blowback while still gets decent fps and shots per CO2.
The Blowback had more feedback then I thought it would.
Mine seemed to be very well centered on target and got a good tight grouping.
CO2 is very well hidden in the handle.
Good weight fit and finish to it.
Glad to see a World War BB replica pistol!
Almost all metal.
Cons:
Had a rather heavy trigger for a single action only gun.
CO2 screw may be a bit hard to tighten for people with sausage fingers.
Some people may not like the high gloss finish.
Comments:
There are few older Classic Airguns out there, especially ones from the World War era! On that topic I would also like to see some old Single Action Army Cowboy Revolvers start to show up in the Replica Airgun market! As I was saying it is nice to see this Classic Walther P38 show up in what seems to be a sea of modern styled airgun replicas. Umarex not only came out with a BB shooting Walther P38, they made it very believable in terms of operation, while maintaining good overall airgun performance. I hope this is a trend that continues in the direction of companies offering more quality airgun replicas of guns from the past.
Ammunition Capacity: 18 round full size metal magazine.
FPS: 320.
Trigger Pull: The trigger pull on the KWC M1911 A1 Tac blowback BB Pistol is exactly what you would expect from a true single action 1911 styled pistol. It has a short take up and then a nice light and crisp pull to it. Because of the similar mechanics not only to the trigger but other aspects of this gun, it would make an awesome low cost trainer to be used when your real 1911 can not be.
Accuracy: I shot the KWC M1911 A1 Tac BB gun at a target from 20 feet away in a semi rested position, and it performed well getting a 2 inch grouping just a bit off center of the target. The sights are adjustable for windage so zeroing the KWC M1911 A1 Tac in would not be much of a problem! My initial Chrony testing puts this gun right in the 300-320 fps range which is just fine for this style of heavy full realistic blowback action BB shooter. I also managed to get three very good magazine worth of shots with some extra CO2 left for a potential 4th magazine. If you slow your shooting down and let the gun and CO2 warm up between magazines you can get 4 magazines with this gun for sure.
Build Quality: KWC did a great job with the KWC M1911 A1 Tac. The quality and build characteristics may even be just a bit better than my other KWC/Cybergun blowback air pistols. Everything that should be metal is the same on this as the original, the slide and barrel wiggle are minimal and the finish seems to be wearing fairly well on this KWC airgun. I do expect over time fore some of the finish to wear off on the high points but this can also give the gun some character ;)
Realism: The KWC M1911 A1 Tac BB airgun is as close as you can get to the real steel 1911 A1 45 auto but with an obvious more modern Tactical look to it, the Tactical version has the addition of a: Tac style trigger and hammer, textured grips, ambidextrous safety, adjustable white dot sights, rail for accessories. This gun is nearly all metal with very heavy blowback making it feel real to hold in the hand and shoot.
All metal construction - Good weight and solid feeling gun.
Nice heavy blowback action.
Very Accurate 1911 A1 styled replica in many way.
True 1911 Single action trigger, excellent pull, very smooth and light.
Accurate trigger design and working grip safety.
Decent accuracy, not too bad amount off shots for this style of gun about 3+ good magazines.
All metal full size dropout magazine.
Love the upgraded Tactical features (Tac style trigger and hammer, textured grips, ambidextrous safety, adjustable white dot sights, rail for accessories)
Cons:
Sacrifice fps and shots per CO2 because of the heavy blowback but worth it.
Finish on the Cybergun and KWC guns can ware off on the high points a bit but some people like this look.
Comments:
I love my Cybergun Tanfoglio Witness 1911 as do many of you based on the amount of sales we have had on that unit! After all who does not appreciate such an accurate replica of the Classic Colt 1911 A1 45 auto? The only problem with the classic 1911 is that it is missing a few of todays more modern features and that's what is so nice abut the new KWC M1911 A1 Tac BB Pistol, it takes an all ready great design and makes it even better by adding the Tac style trigger and hammer, textured grips, ambidextrous safety, adjustable white dot sights and rail for add on accessories. So if you're a 1911 fan looking for as close as you can get to the real steel in a more modern version than look no further, this is it!
This is the official Field Shooting Test Video Review for the ASG Bersa BP9CC CO2 Blowback BB Pistol. If you haven't checked out my Table top Video Review for the ASG Bersa BP9CC, make sure to do so as I have some more photos there along with the specifications and details including the Pros & Cons for the this very realistic Bersa airgun replica!
In this part of the review I test the ASG Bersa BP9CC 4.5mm BB Pistol using my Chronograph to see what the 5 shot feet per second average is using a fully charged CO2 cartridge. Even on this rather cold day, the ASG Bersa BP9CC BB Airgun performed even above the factory claimed 350 fps and was very consistent, within a few fps for each shot averaging 366 fps.
I also take the ASG Bersa BP9CC CO2 Blowback BB Pistol back 20 feet and shoot it at a target using a semi rested position (sand bag up front, kneeling in the back) and shoot 10 rounds into the target getting a not too bad 2 inch grouping with this small short barreled blowback airgun. Near the end of the video I use my high speed slow motion camera setting to capture the blowback in both 400 and 1200 frames per second so you can see for yourself how the blowback action works.
All in all the ASG Bersa BP9CC CO2 Blowback BB Pistol performed very well and had no malfunctions, the accuracy was respectable for an action blowback pistol like this one and the same goes for the fps being that the ASG Bersa has both blowback and a short barrel. I was also very happy with the CO2 efficiency getting close to 120 shots (6 magazines) out of a single 12 gram CO2 cartridge.
If you're looking for a compact action BB pistol with great looks, realism and performance, make sure to checkout the ASG Bersa BP9CC CO2 Blowback 4.5mm BB Pistol!
By the way in this video I also test out my new Liquid Image Impact Series Camera Goggles to see how they work to protect my eyes while recording video in first person view.
Watch my Field Test Shooting Vimeo Video Review for the ASG Bersa BP9CC CO2 Air Pistol:
Trigger Pull: The trigger pull on the ASG Bersa BP9CC is light due to its true blowback operation that cocks the internal striker back with each shot taken. For some reason there is a slight creepiness in the trigger when the metal magazine is loaded, but it does not effect the lighter weight of the trigger pull. There is also a fair amount of take-up but the reset is short.
Accuracy: I shot the ASG Bersa BP9CC Blowback Airgun at a target from 20 feet away in a semi rested position, and it performed well getting a 2 inch grouping fairly centered on the target. The sights are non-adjustable, but for me there was no real need to adjust them. My initial Chrony testing puts this gun right in the 350 fps range.
Build Quality: ASG did another great job with the Bersa BP9CC, quality and build characteristics are very similar to my CZ 75 P-07 DUTY reviewed earlier. Everything that should be metal and polymer is the same on this as the original, and the fit and finish is very good in general!
Realism: The ASG Bersa BP9CC BB gun is as close as you can get to the real steel version while still retaining a good overall working airgun, the only real giveaway is the slightly longer but-plate on the magazine (most likely to allow for the CO2 screw tab). It looks very much like the real deal right down to the licensed Bersa trademarks and the 9x19 caliber markings on the slide and ejection port.
Good power and decent accuracy for a blowback gun with good usage of CO2.
Very well made, fit and finish is very good.
Very usable white dot sights.
All metal dropout magazine.
Gun feels great in the hand, love the thin profile.
Cons:
Magazine but plate is a bit on the long side, only telltale sign. also has strange moulding marks on it.
Trigger is a bit creepy when you have a loaded magazine and if you very slowly pull the trigger a BB can drop out of the barrel if holding downward.
Blowback is mild because of the lighter slide and reduced blowback movement.
Comments:
There are few smaller blowback air pistols that not only look great but perform well, this is one of them! I love the thin profile and overall operation of this pistol, for that very same reason the real steel version is doing exceptionally well here in North America which would make this airgun version a must have for any owners of the 9mm Bersa BP9CC. I highly recommend the ASG Bersa BP9CC 4.5mm BB Blowback Pistol to anyone looking for a very good quality and realistic BB pistol that does not compromise performance and build quality.
I am happy to report back to you on all the new cool stuff I got to see at this years 2013 SHOT Show in Las Vegas. Make sure to also watch my Vimeo video at the bottom of this post for some first person styled play by play of my experience at the Vegas SHOT Show 2013. (like you're there with me ;)
First up I want to cover a new gun from ASG, I have been wanting to get my hands on the 4.5mm Bersa BP9CC and I finally got to, not only did I get my hands on it but ASG was kind enough to supply me with one to take home for review. You can get the Bersa BP9CC in both Blowback and non-blowback versions and also in either BB or Airsoft. I opted for the 4.5mm BB Blowback version. I will be reviewing this BB gun very soon!
ASG also had a very cool prototype of an Airsoft CZ Scorpion EVO 3A1 hopefully coming out soon.
While roaming around SHOT Show 2013, I came across an interesting booth from FlashFog Security. I often get people asking me about using an airgun as a home defense weapon and I strongly advise against this. If the intruder is not scared off by the gun there is little an airgun can do to actually stop them. The FlashFog system works by rapidly filling a room with dense fog combined with a strobe light effect which blinds and disorients intruders completely. There is little an intruder can do other then try and get the heck out of there!
UPDATE: FlashFog just added a new section to their website specifically for School Security to help keep our schools safer from potential safety threats! So check it out: School Security Smoke Screen
I was a bit surprised by Gamo this year, they tend to stay away from actual Replica's and generally make BB/Pellet guns that look like popular guns but not any gun in particular. Gamo has a new BB/Pellet MP9 based machine pistol that uses a similar mechanism to their P-25 and PT-85 so it can shoot both 4.5mm BB's and .177 caliber Pellets using a double ended 16 shot rotary magazine. It also has an internal blowback system so it should have some recoil feel to it! I am pretty sure it is semi auto only but still a nice addition to their lineup!
Gamo also brought out a new 4.5mm BB Blowback pistol called the C-15 which has a metal slide and plastic frame, it kind of reminds me of the Umarex HPP in how it looks and feels.
Umarex had several new products that I am sure everyone is going to like! One that I think will do really well is the Steel Force, the Steel Force is designed around the 4.5mm BB shooting Steel Storm platform so it has a 6 round burst blowback operation and holds the 2x12 gram CO2 in the magazine while the BB's go in a 300 round hopper that feeds into a 30 round spring fed internal magazine. Like the Steel Storm it will shoot around 430 fps. The Steel Force has the advantage of being styled after the AR platform so it has a collapsible stock which will make shooting very easy.
Another often asked for airgun replica is the historic German Luger. This year Umarex stepped up to the plate and introduced the Umarex P.08 4.5mm BB pistol. Sorry, no blowback or even a working slide on this one but it is all metal and has a very good weight and feel to it.
If you're a fan of the entry level Umarex XBG then you may be interested in the new Umarex T.D.P. 45 which is very similar to the XBG in looks and features but with a slightly different look to it.
If you've ever wanted to turn your pistol into more of a PDW styled gun, you may be able to depending on which Umarex gun you have? Umarex added a very cool accessory called the T.A.C Converter that converts your Umarex HK USP (BB-Airsoft), SW MP40 (BB), XBG (BB), CZ Enforcer (Airsoft) and Walther P99 DOA (Airsoft) into more of a tactical (PDW) or Personal Defense Weapon complete with for-grip, adjustable rear sight, lots of rail options and a foldable stock.
I am assuming the Crosman M4-177 Pellet/BB Rifle has been doing well for Crosman as they have expanded with some more similar assault styled air rifles. The Crosman MSR77NP pretty much looks like a classic M16 but is in fact a Nitro Piston break barrel pellet rifle able to shoot .177 caliber pellets at 1200 fps (I hope there is a 499 fps Canada version planned too?).
A new takeoff of the M4-177 is the MK-177 which also shoots .177 caliber pellets and 4.5mm BB's using a multi-Pump System but it uses an upgraded more efficient pump system that squeaks out more fps with less pumps. The Crosman MK-177 is designed after the FN SCAR and is available in an adjustable iron sight version or a Red Dot equipped kit version.
One thing you can never get enough of in my opinion is another 1911 pistol! Crosman is introducing their GI Model 1911BB Blowback 4.5mm CO2 pistol, the one they had on hand was more of a prototype so the slide was not operational but it will feature an all metal design, blowback operation, 450 fps and a 20 round drop out magazine. I am sorry to say but it looks like the Crosman C51 has been dropped from Crosman's lineup but if you want a similar styled gun you can checkout the KWC SW40F which is a very close airsoft version.
We recently started carrying G&G Armament Airsoft guns, you can checkout my review of the Xtreme 45. I did stop by their booth and they had some new products on display, the M1 Grand (all wood stock) Airsoft had it's magwell all wrapped up as G&G had a propriety magazine system they did not want their competition to see. G&G also had some very interesting targets that light up, when shot they would react by individually turning off so you could see if you hit it or not.
There was a rather large crowd at the KWA booth but it was a shared booth so it's hard to say what everyone was looking at, the KWA area was pretty full, I did talk to the KWA rep and asked him point blank if KWC and KWA where the same or sister companies and the answer was not at all. There are often a lot of guns that look like they could be from the same company, I guess there is a lot of copying going on ;) One gun from KWA I would love to get my hands on is the Kriss SMG!
Now keep in mind many of these guns I have highlighted today are not available yet and a lot of them should be coming out in the spring time frame so please try to refrain from repeatedly asking when I will review them and have them in the store, it takes time and as much as we all want them now, they get here when they get here!
Watch my Vimeo video of the Replica Aiguns at SHOT Show Vegas 2013
I know I have been talking about this gun for some time now (Since last years SHOT Show) but the truth of the matter is Umarex did not release it all that quickly and when it did finally come out several months ago there was a recall and so the stock that came in quickly left again. So here we are now and I finally get to show everyone this very nice Umarex made Walther P38 BB shooting replica pistol.
At first glance it looks a lot like the Crosman C41, when I was at the 2012 SHOT Show visiting the Umarex booth, I thought they had just rebranded the Crosman's C41. When I took a closer look I could clearly see the difference and realism found in the Umarex Walther P38 version; like full Walther P38 licensing, blowback operation, working safety and slide catch. Pretty much everything that was missing from the Crosman C41. The Umarex P38 is a very accurate copy of a real steal P38 in almost every way.
All in all it looks to be another welcome and very realistic looking blowback BB Replica pistol and in this case one with a history that goes back to the way to World War II.
I have talked about how KWC and Cybergun are really the same product and that Cybergun and KWC products in many cases are really the same gun but with some versions having slightly different markings on the guns themselves.
Today I show you a new 4.5mm Steel BB gun we just brought into the store very closely related to the Cybergun Tanfoglio Witness 1911, or otherwise known as the KWC Model 1911. This new airguns is a Tactical version of the Model M1911 and it goes by the name Model M1911 A1 Tac. It shares the same internal parts as the Tanfoglio Witness 1911 including the 4.5mm Steel BB magazine but the Tactical version is all black and has several updated modern parts that you would not find in a traditional 1911 A1 45 auto replica: Like the tactical trigger, hammer, adjustable white dot sights and accessory rial. This gun would make an awesome IPSC trainer for sure.
At this point there is no 6mm Airsoft version but you can get the KWC Model 1911 and M92 in 6mm Airsoft all metal versions.
I also compare my GSG 92 4.5mm Steel BB pistol I reviewed in the past and show you that it is identical to the KWC same M92 version with the exception of some marking on the slide. Many people even prefer the KWC branded models as they do not have the rather offensive white warning instructions all over them.
So if you're in the market for one of these super popular KWC/Cybergun blowback ultra realistic BB and Airsoft pistols you do have some options to consider...
Watch my Vimeo Video Preview for these very popular KWC/Cybergun Blowback Pistols:
In this part of the review I test the HK G36 KV AEG Rifle using my Chronograph to see what the 5 shot feet per second average is using fully charged batteries. I got pretty much right bang on to the factory claimed 450 fps using .20 gram 6mm plastic Airsoft BB's and consistency was within a few fps for each shot.
I also take the Umarex HK G36 KV AEG Blowback (EBB) Airsoft Rifle back 30 feet and shoot it at a target using a semi rested position (sand bag up front, standing in the back) and shoot in both semi auto and full auto, there really was no real difference in accuracy using both selections, I think the built in magnified scope helped out here to get a very tight 1.5 inch group shooting in semi and full auto.
So far out of all my AEG rifles I would have to say the Umarex HK G36 KV (EBB) performed the best getting very consistent and high fps and tight groupings in both semi and full auto even using light weight .20 gram BB's.
Watch my Field Test Shooting Vimeo Video Review for the Umarex HK G36 KV AEG Blowback Airsoft Rifle:
In this part of the review I test the Smith & Wesson 357 CO2 Pellet Revolver using my Chronograph to see what the 5 shot feet per second average is using a brand new CO2. I got pretty close to the factory (even a bit over) claimed 425 fps using RWS 7 grain lead pellets on this rather cold day so you can expect better fps on a nice warm summer day.
I also take the Smith & Wesson 357 686 CO2 Pellet Revolver back 30 feet and shoot it at a target using a semi rested position (sand bag up front, standing in the back) and again although I did not get teh same half inch grouping I got in my preliminary testing, I did manage to get a nice tight grouping , keep in mind the Umarex Smith & Wesson 357 is an action shooter but is capable of target pistol like accuracy.
All in all the Umarex Smith & Wesson 357 686 CO2 Pellet Revolver performed very well. That said I was able to get tighter groups and higher fps so expect this Umarex high grade CO2 pistol to perform very well for you.
Watch my Field Test Shooting Vimeo Video Review for the Umarex Smith & Wesson 357 686:
