It's a bird, it's a plan, no wait... It's a pellet gun, no it's a cap gun, or is it a blank gun or maybe it's a real gun? Well it shoots lead bullets out of the barrel using gun powder so who really know's what we should call it? At least here in Canada you don't need a license to buy or own the Pedersoli Derringer Guardian #11 4.5mm .177 Pellet Pistol so that's a good thing :)
So on with the Field Test Shooting Review results... Right off the top, I have no Chronograph test result, try as I did I could not get my Chronograph to read the pellet speed in the rather low light situation I had today, even with a bunch of added extra lights :( I would say off hand that it was shooting somewhere in the 350-450 fps range and when I do get a brighter day I will pop outside and shoot a couple rounds off and post the updated info here for you all, so check back in a bit if this interests you.
What I can tell you for sure is how this gun shot in terms of accuracy. I was expecting to spray pellets all over the target because there is no back sight on the Pedersoli Derringer Guardian #11 4.5mm .177 Pellet Pistol, there is just a post sight up front. I was not even sure if I was going to get all the pellets on the paper. I even setup my target at the 20 foot mark just to be safe and as per usual I was using a semi-rested position by placing a sand bag to rest my hands on and then sitting on my knees in the back, pretty stable all around.
I started off the target test by aiming dead center but quickly found that I was shooting about 6 inches high, so my next 5 shots I aimed 6 inches below the bullseye and low and behold 4 out of 5 of the shots landed within 1.5 inches of each other. So I guess having a rear sight is over rated! If you can figure this gun out, the rifled barrel will direct each pellet straight and true so I think it really comes down to knowing how to line up the front sight with an imaginary rear sight and don't try to shoot really small targets far away. Once you get used to where to point the Pedersoli Derringer Guardian #11 4.5mm .177 Pellet Pistol, you should easily be able to hit a pop can out to 20-30 feet with no problems.
Of course you have to reload this pistol before each shot which consists of cocking the hammer, placing a pellet in the front of the barrel and pushing it to the back with the loading ram rod and then positioning a #11 percussion cap on the primer nipple. Not a rapid fire gun at all but you do appreciate each shot considering the work involved. I also found pre-rolling the back side off my pellets helped to reduce the rear diameter so that the pellets loaded into the barrel much easier. You may have to blow out some residue between each shot which is not something I would recommend with most guns but it's very clear that this pistol is safe since in order to see the barrel obstruction there would be no percussion cap loaded onto the gun.
The Pedersoli Derringer Guardian #11 4.5mm .177 Pellet Pistol is a very unique pellet pistol and actually kind of fun to shoot since it involves a bit of work for each shot and of course some hands on time to figure out exactly how and where to point it to get accurate target results.
Make sure to watch my second Chronograph Test where I was able to get some readings for you!
It's that time of the year again where I dread having to go outside and do my Field Test Shooting Reviews, it's way too cold so the CO2 guns are not performing at their very best, neither am I since all I'm thinking about is "let's get this over so I can go inside and warm up with a nice cup of coffee ;)". It's also dark and dreary which means the lighting is not so good for the cameras or the chronograph, even with a bunch of extra lights setup, it's just not the same as what a nice bright day can do to spruce up the video and get the chrony to read the pellet speeds.
After some playing around with the lighting, I did manage to get my Chronograph to read a couple of shots and it shot just a bit above 350 fps, I would imagine the Daisy Power Line 2003 Blowback Pellet Pistol should get 400" fps easy on a warm day with a fresh CO2. At least we have an idea of whereabouts it shoots.
Once I finished playing around with my temperamental chronograph, I headed back to the 30 foot mark and took aim at my paper target using a semi rested position (sand bag rest up front, standing in the back). I shot the rest of the magazine, which was around 10 rounds left since I was originally loaded up with 30 rounds and ended up using a lot of them trying to get my Chronograph to read for the first part of the field shooting test.
Even with the fairly wide open sights, I managed to get a very consistent 1.5 inch grouping out my Daisy Power Line 2003 Blowback Pellet Pistol which kind of surprised me since I did not really feel the sight picture was suited for accuracy. Too much open space side to side but none the less it shoot straight and true and even very well centered on target with only a bit of pull to the left.
In terms of shoot-ability, the Daisy Power Line 2003 Blowback Pellet Pistol felt pretty good, the trigger is not the lightest for a single action only trigger but it is short and the break is clean. I had no miss-feeds or jams which I have heard this gun is prone to with some pellets. I did notice when shooting rapid fire without any pellets in the gun, it wanted to go into short full auto bursts, this may have been the cold weather and/or low CO2 playing into things.
All-in-all the Daisy Power Line 2003 Blowback Pellet Pistol is a nice air pistol to shoot even though it is a bit unorthodox looking, kind of a shame it's no longer in production. If you can find one in good working condition at the right price, pick it up because you may not get another chance.
Another non-gun video, but there is some really cool water-slide footage starting right around 6:30 for you action-only fans.
I was away with the family for a few days, we left early Saturday and got back late Tuesday night, most of the first day was spent traveling to Seaside Oregon, once we got there we spent the first two nights at our WorldMark time share, Seaside location. The WorldMark Seaside Resort is situated right on the ocean beside the end of the Lewis & Clark Trail. As luck would have it, Oregon was going through a record breaking temperature low and it was very cold even for this time of year but we still made the best of it by bundling up and doing some walking around on the beach and street shopping.
We then traveled the 3.5 hours to the Great Wolf Lodge Water Park in Grand Mound Washington and immediately got into our bathing suits and ripped up the slides :) The kids really loved it at the Great Wolf Lodge and of course want to come back again sometime soon. The Lodge itself is amazing, it's like a full tiny city with everything you need, lots of places to eat including a bar and grill, shopping, games rooms, mini golf and even a Starbucks on location. Of course the water park is the main attraction and the best slide was the Howlin Tornado!
Enjoy the video and if you have a family I highly recommend both locations :)
Trigger Pull: The trigger pull on the KSC M11A1 GBB Airsoft Machine Pistol is pretty much exactly what you would expect from this fast firing single action only semi and full auto machine pistol, it has a really short take-up and then a nice crisp light trigger pull. Since it is an open bolt system, you will need to pull back the bolt for the first shot, releasing the trigger releases the bolt, just like with a real M11A1.
Accuracy: At this point because I received this gun from another collector in used condition, it is not working 100%, the hop-up bucking was damaged and the new ones I ordered are not the correct versions for this Airsoft gun. It does shoot but it is temperamental, sometimes the bolt will not cycle all the way and I have no idea how this is effecting the fps and accuracy. It would not be fair to test it in this condition, hopefully I can find the right hop-up bucking for it and do the Field Test Shooting Review at some point.
Build Quality: MyKSC M11A1 GBB Airsoft Machine Pistol has been used a fair bit so it is somewhat battle scarred, still it looks pretty good and other than the Hop-up bucking problem I am having it should be in working condition, unfortunately without the correct hop-up bucking, this gun will not work properly. Hopefully I can find a hop-up bucking? Even though much of this machine pistol is plastic externally, it has held up very well, the metal parts do also help to balance it off and give it a decent overall 3 pound weight which feels good considering it is such a small gun.
Realism: The KSC M11A1 GBB Airsoft Machine Pistol is a very close copy of the real steel Cobra M11A1 Machine Pistol, all the parts appear to function just like the original Cobra RPB Industries M11A1 and it even field strips in the same manor. The full licensing and trademarks also help to make this replica very believable.
Very realistic and accurate replica with full Cobra RPB Industries licensing.
Even though there is lots of external polymer, it still has good weight to it.
Full metal 40 round drop out magazine, holds BB's and Gas.
Everything works like the original, field strips and lots of mechanical parts.
Shoots in both semi and full auto.
Cons:
Hard to get here in Canada and hard to get parts here in Canada.
Mostly plastic main build - Limited usage of metal and steel.
Have no idea how it will perform because it is not functioning at 100%.
Comments:
Well I've pretty much said everything I can say without actually shooting it? Even though my used KSC M11A1 GBB Airsoft Machine Pistol is not in 100% working condition, I still like having it as I like the replica aspects of owning it, how else would I get my hands on a .380 caliber full auto machine pistol here in Canada ;) And you never know, I may just luck out and find the proper hop-up bucking for it and then have the chance to do my Field Test Shooting Review for you all :)
My Vimeo Table Top Review of the KSC M11A1 GBB Airsoft Machine Pistol:
Trigger Pull: The trigger pull on the Daisy Power Line 2003 Blowback Pellet Pistol even though it is single action only, is a bit heavier than you may expect, it is more of a medium pull with a very short take up and then somewhat unexpected release due to the medium to heavy pull. Quick shot succession should be achievable though due to the short trigger pull length.
Accuracy: Well we will have to find out in my followup Field Test Shooting Video Review? And I really hope that this pistol is in working order so I am able to bring that review to you shortly. I am expecting it to produce around 400 fps and some decent accuracy with its rifled barrel.
Build Quality: The Daisy Power Line 2003 Blowback Pellet Pistol is made in the US and is primarily a plastic built air pellet pistol, it does have some metal internal parts along with the screws, barrel, cross-bolt safety and CO2 Tab. Fit and finish seem to be fairly decent, in terms of reliability I have no idea but my hopes are high. I have heard that this pistol can jam if not using pellets that are agreeable with it.
Realism: The Daisy Power Line 2003 Blowback Pellet Pistol is not really a replica so to speak, it does kind of resemble a bloated version of a Browning High Power but is much larger and out of proportion when comparing the two of them. The actual mechanical aspects of this gun are not like any other gun I have every come across, specifically when it comes to the 35 shot rotary magazine as the pellets spiral internally from front to back. The single action blowback mechanism is also very unique to an airgun pellet pistol, it has been said that this pistol can be converted to full auto but I have no intensions of doing so.
If you have a Power Line 2003 then you have a really rare gun from Daisy.
True single action Blowback operation.
One of the only Pellet Pistols that can be converted to full auto.
High capacity 35 round pellet magazine.
Made in the US.
Cons:
No longer in production.
Kind of large for a pistol, not true to scale.
Mostly plastic build materials
None adjustable sights.
Comments:
I have had an interest in the Daisy Power Line 2003 for some time but did not know how or if I would ever get my hands on one and lucky for me it finally happened :) The main interest here is simply that it is the only pellet pistol I know of that has a true single action blowback operation and to top things off it has a 35 round magazine! Sure there is the implication that it can be converted to full auto but for me I really want to keep this pistol in factory condition, I have other guns that shooting in full auto if I feel the urge to go Rambo on anything ;) Definitely stay posted for my Field Test Shooting Review for this rare Daisy pellet pistol.
My Vimeo Table Top Review of the Daisy Power Line 2003 Blowback Pellet Pistol:
WARNING!! This post is not about guns, but it is about some really cool fun stuff or I wouldn't be doing it ! So if you're not into having fun in the great outdoors quading then don't watch it ;)
I struggled a bit with this pistol during this Field Test Shooting review, mainly just in the accuracy portion. Perhaps the G&G GS-801 CO2 Blowback Airsoft Pistol did not like the .36 gram BB's I was using, maybe a bit too heavy or perhaps the hop-up did not agree with the size of this Airsoft round. Either way, my accuracy test did not do so well! I may give this gun another go at some point using a different Airsoft BB and perhaps simply using the iron sights over the built in laser just in case that was the issue?
As per usual, I tested this pistol out using my Chronograph to see what kind of actual feet per second rating I get from it. I fired 5 rounds from the G&G GS-801 using .20 gram plastic Airsoft BB's and this CO2 semi auto blowback pistol shot a very speedy 415 fps average.
Next up was the accuracy test, I decided to setup at the 30 foot mark and I shot a total of 10 rounds from my G&G GS-801 CO2 Blowback Airsoft Pistol using a semi rested position, (sand bag for a hand rest and standing in the back). My grouping was all over the place vertically (about 6 inches) but not so bad horizontally (about 2 inches). It makes me wonder if the hop-up was playing into it or maybe my laser sight was moving around up and down?
The trigger pull on the G&G GS-801 CO2 Blowback Airsoft Pistol is kind of different, it is single action only since the blowback action cocks the hammer back with each shot. There is a fair amount of take up with next to no resistance followed by the release point which seems kind of heavy after the soft take-up section, you need to keep applying pressure and then with no real movement it will just suddenly release so it's kind of hard to predict without practice. During the take-up portion of the trigger pull, a BB is loaded into the barrel and the laser sight will automatically turn on if you have the laser in the active position.
Over all the G&G GS-801 CO2 Blowback Airsoft Pistol is a well put together Semi Auto Pistol, it looks good, performs nice and hot and is a lot of fun to shoot, I would have liked to have seen better accuracy from it but in a heated Airsoft battle at close range, the built in laser will get you on target quickly and as long as you are not shooting at really long ranges you should be just fine.
Since both the Gold ASG Dan Wesson and the G&G G731 Airsoft Revolvers both have the 2.5 inch barrels on them and in many ways are very similar (at least mechanically), I thought I would not only do my Table Top Review but also my Field Test Shooting Review using both guns side by side so we can really get an idea of how they perform and compare.
As per usual, I test both pistols out on my Chronograph to see what kind of real world feet per second rating I get, since they are 6 shot Revolvers, I fired 6 single action rounds from each gun using .20 gram plastic Airsoft BB's and averaged out the string. Both guns shot a little bit over 400 fps with the Dan Wesson having just a bit of a higher fps over the G&G G731.
Next up was the accuracy test, I decided to setup at my 30 foot mark so that any accuracy differences would be more noticeable, again I shot 6 rounds from each gun while I used a semi rested position, (sand bag for a hand rest and standing in the back). This time I would have to give the slight edge to the G&G G731 as it seemed to shoot just a bit tighter grouping over my Dan Wesson Gold. Both guns shot pretty close to a 2 inch 6 shot group.
Both pistols have pretty decent single and double action triggers, there is a some noticeable friction when shooting in double action due to the way the barrel seals against the cylinder so you may want to shoot in single action when going for the most accurate of shooting.
When it comes to sight picture the Dan Wesson does have a fully adjustable rear sight but the G&G G731 gets the job done with it's simple yet effective grove sight which I kind of preferred with this style of short barreled revolver.
If you want more of that combat look with some Gold Bling than perhaps the Gold ASG Dan Wesson is the one for you? Perhaps you want something like the G&G G731, as compact and simple as it gets that you know you can count on as a backup ready sidearm. There isn't a bad choice here with either of these nice compact Airsoft Revolvers.
Trigger Pull: The trigger pull on the G&G AR styled Airsoft CM16 Raider is very smooth, the CM16 Raider uses a mechanical trigger that once the charging handle has been pulled back or "charged", works in a single action only manor with a slight bit of take-up and then a light predictable release. Each time the closed bolt gas blowback system shoots a round in semi or full auto, the internal action is ready for the next single action shot.
Accuracy: So far I have not tested Version 2 of the G&G CM16 Raider, but I have tested Version 1 so here are the result I got with Version 1 until I do my official Field Shooting Test with Version 2. When shooting from a 30 foot distance I did get some nice closely grouped shots from the G&G CM16 Raider Gas Blowback but when shooting in full auto it did spread apart somewhat, maybe from the GBB recoil? Version1 of the G&G CM16 Raider GBB shot an average of just over the 325 fps, I was using .25 gram BB's and it was a cool day so you can expect higher fps out of the G&G CM16 Raider when conditions are better.
Build Quality: The G&G CM16 Raider GBB being built on G&G Combat Machine Platform is targeted more for the price conscience person. The quality is consistent and good and I did not mind having more plastic in the G&G CM16 Raider GBB as my plan from the beginning was to add a lot of extra accessories and starting out with a somewhat lighter footprint made the gun still relatively usable even when all geared up with extra accessories. I also feel the plastic or polymer fiber upper and lower receiver and RIS rail system will also wear better than steel as it is more likely to flex rather than break in many situations, not to mention metal will show scratches and wear more over time.
Realism: Airsoft AR rifles in my opinion are very realistic in general, even the AEG versions work just like the real steel AR's with working charging handles, dust covers, bolts, magazine, adjustable stocks and sights, but I would have to give the advantage to the gas Blowback systems like the G&G CM16 Raider GBB as it has a full internal bolt with some decent recoil, it can also be field striped very similarly to a real AR15 rifle. The shot count is more like what you would find in an M16 or AR rifle which means you will need to consider ammo shot assuage and reloading more carefully when using it in an Airsoft game.
Super affordable Gas Blowback Airsoft AR M16 styled Rifle.
Very high rate of fire in full auto.
Polymer shell is both light and very durable, does not show scratches or wear as easily as metal.
All most every part is operational - Fully Ambidextrous now.
Can be fully customized, lots of mounting points on the RIS Rail system.
Fully adjustable Crane Stock.
Removable rear Iron Sight can be swapped out for other sighting systems and hardware.
Version 2 is a significant upgrade from Version 1.
Internals can be swapped over to make it an AEG gun.
Cons:
Some people may not like the polymer RIS rails and upper and lower receiver?
Would have liked to have seen some sort of a plate over the pistol grip to finish it off.
Comments:
I already really liked Version 1 of the G&G CM16 Raider GBB Airsoft AR Rifle and even bought a bunch of magazines and gear to sport mine up for use in some local Airsoft games, the upgrades and improvements found in Version 2 are the icing on the cake! I am hoping the internal performance enhancements will increase the FPS just a bit and Gas efficiency somewhat over Version 2 but will find out when I give it a thorough testing shortly. If you have been a bit scared off by the higher prices of some GBB Gas Blowback Airsoft rifles then perhaps take a look at the G&G Combat Machine Platform CM16 Raider in GBB, it may just change your mind about Gas Blowback Airsoft rifles!
My Vimeo Video Review for the G&G CM16 Raider Airsoft GBB AR Styled Airsoft Rifles:
Materials: Mostly metal construction with a few plastic parts.
Weight: 1.64 pounds (742 grams)
Barrel: 4 inches, metal non-rifled.
Propulsion: CO2 x 1.
Action: Semi auto blowback, single action only.
Ammunition Type: 6mm plastic Airsoft BB's.
Ammunition Capacity: 14 round magazine.
FPS: 400+
Trigger Pull: The trigger pull on the G&G GS-801 CO2 Blowback Airsoft Pistol is kind of different, it is single action only since the blowback action cocks the hammer back with each shot. There is a fair amount of take up with next to no resistance followed by the release point which seems kind of heavy after the soft take-up section, you need to keep applying pressure and then with no real movement it will just suddenly release so it's kind of hard to predict without practice. During the take-up portion of the trigger pull, the laser sight will automatically turn on if you have the laser in the active position.
Accuracy: This is somewhat yet to be determined in my upcoming Field Test Shooting portion of this review but I am looking forward to testing out the laser sight to see if it will help to get nice tight groupings? I will put a link in here when I have completed my Shooting Field Test review.
Build Quality: This is an almost all metal air gun with good fit and finish and a nice hefty to it since it is not large in the hand. The only real plastic parts are the grips, laser and CO2 tab, even the drop out Airsoft BB only stick magazine is all metal. The finish seems to be wearing really well and not rubbing off on the high points at all which is nice to see.
Realism: The G&G GS-801 CO2 Blowback Airsoft Pistol is not a replica of any manufactured gun that I know of, it does have a PPK or Makarov look to it even though it is larger than both semi auto pistols. I do like the open ejection port, true semi auto blowback action and working slide catch release.
Lots of metal and good overall weight for it's size.
Blowback operation (enough to give it some shot feedback and also cocks the hammer for easy single action trigger pull).
Should have a decent fps for a blowback Airsoft pistol.
Fully adjustable laser sight built into the pistol rail.
Fit and finish is very nice.
Magazine is all metal.
Rain for accessories.
Open ejection port and working slide catch
Nice and compact, has a sleek profile.
Cons:
Stick mag ejection is a bit clumsy.
Slightly exposed plastic CO2 tab.
Trigger take-up is a bit long and the release is kind of spongy.
Comments:
The G&G GS-801 CO2 Blowback Airsoft Pistol is a real nice solid little gun, It has lots going for it; The pistol is pretty much all metal including the frame, it has true blowback single action firing, a built in laser with trigger activation, you can field strip it, it has an open ejection port with working slide catch and the size and weight are perfect for an Airsoft backup sidearm. I am really looking forward to my upcoming Field tests Shooting review, and have high hopes this high value Airsoft pistol will perform very well for me.
My Vimeo Video Review for the G&G GS-801 CO2 Blowback Airsoft Pistol:
Trigger Pull: Both of these pistols have about the same style of triggers, they both shoot in true revolvers style offering single and double action triggers. The double action has a bit of friction to it since the cylinder is being rotate during the first part of the trigger pull and there is a spring fed metal gasket between the barrel and the cylinder that creates a seal but does apply pressure and results in some friction and a heavier trigger pull in double action. Single action is much lighter on both guns.
Build Quality: These detailed revolver are really well built! Both are almost all metal with just a few components made out of plastic, like the handles on both guns and the CO2 screw tab on the Dan Wesson. Both revolvers grips gave me just a bit of concern, you will need to be careful when snapping in the grip on the G&G G731 and the Dan Wesson grips have been known to ware a bit with heavy use. The finish on both of these guns is amazing and while the Silver finish on the G&G looks just like polished stainless steel, the Gold finish on the Dan Wesson offers a very unique and customized finish not found on too many guns. And if you just want classic black then there is always the G&G G731 in standard black as an option.
Realism: The ASG Dan Wesson and G&G G731 revolvers are as close as you can get to real six shooters, all the parts work pretty much like a real revolver, the realistic loading of the metal shells not only make it feel like you are handling a real revolver but also finish off the look making it really hard to tell that both these pistols are in fact Airsoft Revolvers.
G&G G731 is super compact and flush, great out of the way back up side arm.
No Red Tip on the Canada version.
Cons:
Plastic CO2 screw tab on the Dan Wesson (but is well hidden and protected).
A bit of concern with wearing and usage on the grips for both guns.
No adjustable sight on the G&G G731 but super clean looking.
Red tip on the US version :(
Comments:
As with all of these shell loading revolvers, they are just so realistic and really fun to load up and shoot. You actually get a bit of time in-between shooting to take a breath and enjoy the entire experience rather than just unload round after round with some of the other super high round magazine guns. I love the compact size of both guns, perhaps the G&G G731 just a bit more with it's super clean edges and even smaller profile. But on the other hand the Dan Wesson ASG 2.5 inch has that more aggressive combat look if that is more to your liking! Either way, both guns make a great choice for an out of the way revolver styled side arm when you need that extra backup firepower!
My Vimeo Video Table Top Review for these compact realistic Airsoft Revolvers:
Every so often I come across some interesting guns that people are willing to trade or sell me, if the price is right or the trade involves a gun I can part with, then I go for it and hopefully end up with something I may not be able to get new or that for me is hard to acquire in Canada.
My most recent trade added two new guns to the collection, a KSC M11A1 Airsoft Machine Pistol and a Daisy Power Line 2003 .177 Caliber Pellet Pistol.
Both of these guns are very hard to get since the KWC Airsoft M11A1 shoots a bit too week for import into Canada, and the Daisy 2003 is no longer in production.
The KSC M11A1 is a 6mm Airsoft pistol that shoots in both semi and full auto using a Gas Blowback open bolt system, it is a replica of the .380 Caliber Cobra RPB Industries M11-A1. Mine came with a mock suppressor and 7 magazines, although not all of them are in working condition. The KSC M11A1 is in working condition but needs a new Hop-up Rubber Bucking which I have on order.
The Daisy Power Line 2003 seems to be in really good condition but still needs to be tested, it is one of the only true blowback semi auto pellet pistols I know of, what I mean by this, is it has a true blowback system with a true single action trigger which means it can be converted to full auto which is one of the reason Daisy may have discontinued it. The Daisy Power Line 2003 uses a very interesting 35 round rotational magazine. Some say it is loosely styled after a Browning High Power pistol.
Stay posted for reviews on both of these pistols down the road.
You may wonder why I am doing another video on the G&G CM16 Raider Gas Blowback Airsoft AR Rifle? That's because the one I have here in this Update Video is Version 2 and yes there is a difference. So far I can only tell you about the obvious stuff since I really have not tested it out to see if there are any other performance gains with Version 2 over Version 1.
G&G has made some improvement with Version 2 enhancing several areas:
First off, there is now a selector switch on both sides of the receiver allowing for left or right handed use.
Carrying on with the ambidextrous theme, G&G also added a magazine release to the left side of the receiver.
Another missing feature was a bolt lock out when your magazine was empty, this has been added and so the bolt will lock back about 1/3 the way back locking out the gun and letting you know when you are out of ammo.
The bolt release on Version 1 was just for show and did not function. On Version 2, with the bolt lock, G&G also added a working bolt release.
Those are some pretty significant improvements to the G&G Armament CM16 Raider GBB Version 2 in my books! So now it's time to test it out and see if full auto mode has been improved. I found with Version 1, that when using full auto, the G&G CM16 Raider GBB would have some trouble getting through a full mag dump but when shooting very quickly in semi auto had no problems at all.
Another Halloween Costume Contest has completed and another Winner must be announced! This year I had everyone else vote or should I say "Thumbs Up" their favorite Halloween Costume Videos and so hopefully nobody gives me crap this year for being unfair ;)
If you have not checked out my Halloween Costume Contest Video Playlist then make sure to do so and thanks again to all the contestants who took part in this years Halloween Costume Contest.
This years winner was Hideki Ryuga with his Resident Evil Hunk Halloween Costume, he got 154 thumbs up at the time I checked his video out. To be fair to some of the late unloaders, I ran the contest video viewing and rating time for an extra week to give everyone some more time to check out all the videos.
Another quick revisit of the KWC/Cybergun M92 Beretta - Taurus full metal, full blowback, CO2 4.5mm Steel BB pistol series. They come in several flavors but are all made by KWC and in many cases redistributed licensed by Cybergun. This Field Test Shooting Video Review focuses on the Cybergun Swiss Arms P92 version.
Now that I have a more standardized Field Test Shooting format, I though I would revisit this series of KWC/Cybergun Beretta - Taurus Replica BB Pistols and do a follow up Field Test to get some more camera angles and hopefully a nice tight target grouping using my standard semi rested position from 20 feet away.
I also incorporate some high speed video near the end of this Field Test Shooting video Review to go along with the Chronograph and target portion of the Filed Test Shooting review.
The KWC - Cybergun Full Blowback All metal serious of Replica CO2 BB Pistols has been hugely popular over here at Replica Airguns and for good reason, they are very realistic in looks and operation, are priced very respectably and replicate several of the more popular semi auto pistols.
So this is not the first time I've reviewed the KWC/Cybergun Series of full metal, full blowback CO2 4.5mm Steel BB pistols. The most popular version being the Cybergun Tanfoglio Witness 1911 since it was the first one on the scene. These BB shooting 1911 replicas come in several styles and can be found in both 4.5mm Steel BB and 6mm Airsoft versions.
They are made by KWC but can also be found redistributed by Cybergun with either the Tanfoglio Witness or Swiss Arms licensing on them.
Today I revisit my Field Test Review since it has been a long time and the way I conduct my field tests has changed a bit so I wanted to test this popular 1911 CO2 Replica using multiple cameras and a more scientific testing approach.
In a nutshell, the KWC/Cybergun Swiss Arms P1911 with it's true 1911 single action trigger and full blowback shoots much like its real steel counterpart with less kick of course. It is capable of nice 1.5 inch groups from a 20 foot semi rested shooting position and shoots right around 300 fps which will put a steel BB right through both sides of a water filled pop can.
You really can't find a more fun and realistic BB pistol out there, probably why this air pistol has been such a favorite with replica airgun fans.
It's Movember again, time for us guys to band together and grow a Moustache for Men's Health! It doesn't really matter what age you are because Protate or Testicualr Cancer as well as Mental Health issues can hit us men at any age or affect someone close to you.
In this YouTube Overview video I show several NcSTAR Accessories, we carry a fair amount of NcSTAR products our Canada Replica Airguns Online Store and I thought it was time again to showcase some more NcSTAR items.
So here it is, my X-Men Wolverine Costume for the 2013 Replica Airguns Halloween Contest Giveaway. No I am not competing, but I wanted t get involved since dressing up for Halloween is fun.
X-Men Wolverine in pretty simple, pair of jeans, white wife beater, brown leather jacket, cool belt buckle, dog tags, cigar, grow and trim the beard and of course attach some blades to your knuckles ;)
Hope you like it and don't forget to upload your Halloween Costume video and let me know when you have it up.
