Type: BB air revolver Manufacturer:Umarex. Model: Colt Python 375 Materials: Almost entirely all Metal. Weight: 2.75 pounds (1218 grams). Barrel: 5.5 inches, metal non-rifled. Propulsion: 12 gram CO2. Action: Revolver, single & double actions. Ammunition Type: 4.5mm steel BB's. Ammunition Capacity: 6 round cylinder. FPS: 400.
Trigger Pull: The trigger pull on the Umarex Colt Python 357 Magnum Chrome CO2 BB Revolver is good in both single and double action, it’s nice that you have the shorter lighter single action trigger for slower more accurate shooting but you can also blast away in double action when you feel like it. The hammer on the Umarex Colt Python 357 Magnum Chrome CO2 BB Revolver is firm with not very much wiggle which some other revolvers in this category do have.
Accuracy: Based on my results shooting the Umarex Colt Python 357 which is essentially the same gun in a different finish. The results I got shooting my 6 round group from a 30 foot out semi rested position where good overall. Vertically there was about a 2 inch spread while horizontally there was about a 1 inch spread. I did find the plastic tips on the brass shells seemed to be a bit tight at first and this is when I did most of my Chronograph and target shooting. I believe the tightness effected the consistency of the FPS which also effected the accuracy especially up and down. I did get one shot out of the Umarex Colt Python 357 well over the claimed 400 fps but again the fps was rather erratic most likely because of the snug BB fit due to shell break-in.
Build Quality: The Umarex Colt Python 357 Magnum Chrome CO2 BB Revolver being mostly metal has a very good build quality and is on par with the Dan Wesson 715 shell loading revolver. It has a nice weigth adn balance to it and feels really good in the hand! The only real plastic I could find was in the grips and the shell tips. Fit and finish was also good with no noticeable chrome wear or sloppy workmanship. It will be interesting to see how the Chrome finish wears over time compared to the black finishes fodun on most KWC made Airguns.
Realism: TheUmarex Colt Python 357 Magnum Chrome CO2 BB Revolver overall is a close copy a the real steel Colt Python 357 styled revolver. I did notice the rear portion of the receiver (between the rear cylinder and hammer) to be a bit longer perhaps to accommodate the CO2 valve length, but other than that, this pistol is super close to the original Colt Python 357 styled revolver it is based on. Again being all metal gives this CO2 BB revolver very realistic weight and feel and the loadable brass shells make using this gun almost exactly like using a real shell loading revolver but for much less cost per shot and of course a lot less recoil on the hands and noise to be had.
Pros:
Shells loading revolver give you the feeling of loading and shooting a real revolver.
Mostly all metal design.
Lots of detail, well made, chrome looks nice, not sure if it will wear better than the black finish found on most KWC made pistols?
Good overall weight, almost 3 pounds.
Should have good overall power, accuracy and shots per CO2 (based on my previous Colt Python testing).
Fully adjustable sights.
Well hidden CO2 Screw.
Recessed barrel.
Nice Trigger pull in both single and double action.
Cons:
Grips are a bit rough and wood grain is only OK.
Grips may be a bit large for people with small hands.
Decent enough Colt Python 357 replica but the frame is a bit long between the cylinder and the hammer.
Comments:
It’s been a while since I reviewed a Shell Loading Airgun and this one is pretty much the same Airgun I have reviewed in the past in both the KWC and Umarex Distributed forms. It has been almost 6 years since I took a look at one on my table and it still hods up today. I plan on performing another Field Test Shooting Review for the Umarex Colt Python 357 Magnum Chrome CO2 BB Revolver to see if I can replicate the same good results I did back in 2014 when I tested it out on my deck. If you’re looking for a shell loading revolver in the 357 design then for sure checkout the Umarex Colt Python 357 Magnum Chrome CO2 BB Revolver as an option.
My Vimeo Table Top Review for the Umarex Colt Python 357 Magnum Chrome CO2 BB Revolver:
Type: Pellet Revolver. Manufacturer: Gamo Model:PR-776. Materials: Mostly metal construction. Weight: 2.2 Pounds (1 kg). Barrel Length: 6 inches Total Length: 11.5 inches. Propulsion: CO2 x1 Action: Revolver single and double action. Ammunition Type: .177 caliber pellets. Ammunition Capacity: 8 rounds per magazine. Max FPS: 400+ fps.
Trigger Pull: The Gamo PR-776 CO2 .177 Caliber Pellet Revolver has your traditional revolver single and double action trigger setup. In double action, the trigger is going to be a bit longer and heavier but it feel fairly smooth with no real friction points and I would consider it to have a medium trigger pull. When you cock the hammer back placing the Gamo PR-776 CO2 .177 Caliber Pellet Revolver in single action, the trigger pull becomes very short with virtually no take-up at all and the weight of the trigger is very light allowing for more accurate shots.
Accuracy: Make sure to watch my Field Test Shooting video for the Gamo PR-776 CO2 .177 Caliber Pellet Revolver where I test out the velocity and accuracy in the Replica Airguns Indoor Airgun Shooting Range. In summary the Gamo PR-776 CO2 .177 Caliber Pellet Revolver shot a little bit hotter than claimed at just over 400 fps using around 7 grain lead pellets. In terms of accuracy with a total of 16 shots the grouping spread out to around 4 inches but I am pretty sure a different pellet choice may have made a difference.
Build Quality: The build quality of the Gamo PR-776 CO2 .177 Caliber Pellet Revolver is pretty good overall. It is mostly all metal with the exception of the grips of course, Fit and finishes looks good, everything feel snug adn tight with the exception of the pistol grips. I feel like the grips could easily move out of place and get caught on something. This is not a problem when shooting, more so when in a holster. The Gamo PR-776 CO2 .177 Caliber Pellet Revolver feels good in the hadn't, nice and solid and with a good weight to it.
Realism: The Gamo PR-776 CO2 .177 Caliber Pellet Revolver is a decent looking Airgun in the style of a traditional revolver, I wouldn’t say it’s an exact replica of any specific revolver in production but it does tick off all the boxes in terms of looking realistic. The weight and feel for now and the Gamo PR-776 CO2 .177 Caliber Pellet Revolver also has a recessed barrel and hidden CO2 crew. The only real giveaway would be the cylinder size as it is a bit smaller than expected and of course is chambered for .177 caliber pellets.
Pros:
Good power over 400 fps using actual lead pellets.
Quicker reloading over shell loading revolvers
More shots per magazine reload, 8 versus 6.
Comes with two metal 8 round magazines.
Traditional single and double action trigger.
White dot front sight with fully adjustable rear sight.
Good weight and feel to it.
Fit and finish look good.
Recessed barrel for realistic looking barrel opening.
Should be able to use a dovetail type scope mount for adding on a red dot or magnified scope.
Cons:
Not a fan of the loose pistol grip setup to access the CO2.
Was hoping to get a bit tighter grouping but may have been a pellet choice issue.
Comments: It was nice reviewing the Gamo PR-776 CO2 .177 Caliber Pellet Revolver as it was a bit different then most of today shell loading revolvers. I like that the Gamo PR-776 CO2 .177 Caliber Pellet Revolver still offered a realistic looking cylinder that the shell loading revolvers have but with the moon clip style magazines that allow for quick adn easy reloading of 8 rounds at a time. The velocity or power of the Gamo PR-776 CO2 .177 Caliber Pellet Revolver was even a bit high than Gamo claims using PBA Platinum pellets since Gamo claims 400 fps using these 5.1 grain lead pellets. My testing with closer to 7 grain pellets yielded fps up and over 400 fps. All the Gamo PR-776 CO2 .177 Caliber Pellet Revolver needs is to be just a little bit more accurate but I feel this may simply be more of a pallet choice, once you find a pellet the Gamo PR-776 CO2 .177 Caliber Pellet Revolver likes I am pretty sure it will deliver accurate shots.
My Table Top Review for the Gamo PR-776 CO2 .177 Caliber Pellet Revolver:
Make sure to watch my upcoming Table Top Review for the Gamo PR-776 CO2 .177 Caliber Pellet Revolver where I go over the specifications, pros and cons and show it up nice and close. In this Field Test Shooting Video I determine what the accuracy and velocity of the Gamo PR-776 CO2 .177 Caliber Pellet Revolver by testing out the fps with my Chronograph along with a accuracy test shooting a paper target at a distance of 30 feet away using a rested shooting position.
For the velocity test I placed a brand new CO2 Cartridge in the Gamo PR-776 CO2 .177 Caliber Pellet Revolver and shot five 6.9 grain lead pellets though my Chronograph. Gamo claims their 5.1 grain PBA Platinum pellets will shoot around 400 fps so I was expecting something in the low to mid 300’s but was surprised at a five shot average of 4115 fps with the much heavier RWS6.9 grain pellets. The slowest shot I achieved was 396 fps while the fastest shot was 434 fps. The temperature was right around 24 degrees Celsius or 75 degrees Fahrenheit.
For the next section of my Field Test Shooting Review I setup a brand new paper target 30 feet down range and loaded up two eight round magazines. The results for the Gamo PR-776 CO2 .177 Caliber Pellet Revolver where a bit confusing with both eight round magazines. It seemed like most of the shots wanted to group within about 1-2 inches of each other but I was getting several outliers that extended the grouping to closer to four inches. Not the best performance but as I have found with many guns, sometimes you need to find a pellet that the gun is happy with. the wrong pellet can really make a difference and I am fairly sure this was the case with the Gamo PR-776 CO2 .177 Caliber Pellet Revolver using the RWS pellets. just not the best choice for it.
The Gamo PR-776 CO2 .177 Caliber Pellet Revolver overall performer well, like I said I really think pellet choice will be the deciding factor in how accurate it is going to be. The velocity was very good for a CO2 Pellet revolver considering I was suing actual lead pellets and not the alloy pellets Gamo was using as their reference. The Gamo PR-776 CO2 .177 Caliber Pellet Revolver uses metal eight round magazines which are easy to preload and allow for two additional shots over the more common these days shell loading revolvers, which makes the Gamo PR-776 CO2 .177 Caliber Pellet Revolver more practical as a target pistol allowing for more power and easier loading.
The Umarex T4E TR50 .50 Caliber Paintball Revolver is an interesting Paintball pistol, it has a very different look and also uses .50 caliber Paintballs which are a little bit less common than the .68 and .43 caliber paintball gun I have been reviewing up until now. The Umarex T4E TR50 .50 Caliber Paintball Revolver is some countries is marketed as a self defense gun but those versions do have a little bit more fps and foot pounds of energy. The version I am testing is not marketed here in Canada or the US as self defense products but rather as more of a training Paintball Gun.
Starting with my Chronograph velocity test I placed 5 Rubber Balls through my Chronograph using a brand new CO2. The Rubber balls I am going to say are a little bit heavier than standard Paintballs and Umarex claims the Umarex T4E TR50 .50 Caliber Paintball Revolver is capable of hitting around 360 fps so with the heavier rubber balls I was expecting a little bit under the max fps. I was able to get an average of 328 fps so not bad at all.
Moving on to my accuracy test. I need up placing 10 of my 12 rounds into the paper target as I had two rounds that went off in what I am going to call an uncontrolled manor. The 10 rubber paintball rounds that did hit my paper target that was setup 30 feet down range all hit within about 6 inches of each other daily well centered left and right and a little bit low on the target. Gettin back to the uncontrolled shots, I had a situation where I pulled the trigger and the Umarex T4E TR50 .50 Caliber Paintball Revolver went click as you would expect but no CO2 was expelled and so no round was shot. I thought perhaps the cylinder was caught up so I went to wiggle it to try and free it up. As I did so the gun went off without my finger anywhere near the trigger. I am glad I was using rubber balls since the rubber ball hit my cabinet leaning a biota a mark but really causing any damage. This happened twice with the same cylinder, the second time I was bit more prepared for it and had the gun pointed well downrange. I was not able to recreate this problem again so perhaps the cylinder magazine was not seated properly but this still concerns me a bit.
Overall I really like the Umarex T4E TR50 .50 Caliber Paintball Revolver, it’s a pretty cool looking Paintball Gun with decent accuracy and power, you can even feel a little push back and barrel lift when you shoot it. I also like that you can preload a CO2 and puncture it whenever hypo are ready to shoot with a quick smack on the bottom of the grip. Just made sure to put the CO2 in the right way :)
My systems setup for a more powerful airgun as I was shooting .22 caliber lead pellets with about 11-12 foot pounds of energy. Direct hits passing through the 3/4 inch cut outs had no problem laying down the metal paddles and resetting the paddles was a lot easier than I though it would be even way back 50 feet.
I did not have my Sig Sauer Virtus PCP .22 Caliber Air Rifle perfectly sighted in so I did have to aim low and to the left which made it a bit harder dropping the plates but I did manage to get the job done at least for providing a decent test video fo the Rx Target Systems for the purposes of this video.
Make sure to not only watch my Field Test Shooting video included in this post but also checkout my Rx Target Systems Preview Video where I show it up and close and also go into more details on the Rx Target Systems and how modular and versatile it really is.
I want to thank David Bitkowski from Rx Target Systems for providing me with this sample unit to share with the Replica Airguns community. This video is only a Preview video as I wanted to get the RX Target System out there before I follow up with my actual Table Top and Shooting Videos for it.
For now here are some of the key points I want to get out to everyone:
Mission: Rx Target Systems are meant to bridge the gap between firearms and airguns. They allow high precision shooting on a reactive, three- dimensional, rugged target that can be carted around in a back pack. What makes Rx Target Systems unique is that it is a system. It is so modular and adaptable with interchangable faceplates and paddles. Rx Target Systems are not going to break or get dented or dissembled on the range as many of the lighter gauged steel targets on the market today vs today’s high powered airguns.
Modular
One base allows interchange of faceplates for different target configurations
One threaded axel allows interchange of paddle from 10 gauge to 3/8 inch-thick paddles
Portable
Mount it on a shelf indoors
Mount it on a sawhorse outdoors
Carry it in a backpack or duffle bag- its 10 pounds
Rugged
Solid steel design
Faceplates from 10 gauge to ¼ inch thick
3-Dimensional
Faceplate is offset from paddles
Clipping the aperture does not guarantee a score
Intentions of target configurations
Standard 1 inch bulls.- represents kill zone of many small game at 30 yards, great for sighting in prior to the hunt. Also is ¼ scale of bull used in rapid fire pistol when shot from 8.3 meters. (25 meters distance/100mm bull)
1.2 inch bulls- represents the 4-10 ring of the NRA 10 meter air rifle target. Gears the shooter to consistently hitting the “black” of that target on paper
AAFTA style- represents common kill zones found in American Airgun Field Target Assosciation using 1.5”, 1”, ¾", ½", and 3/8”.
WFTF style- represents common kill zones found in World Field Target Federation using 15mm, 25mm, and 38mm apertures
10-15- Inspired by customer request, uses 10mm and 15mm apertures. High-Precision shooting.
This isn’t a SHOT Show 2020 Interview but most certainly worth reporting on. While walking around SHOT Show I ventured into the Chiappa Booth as I own a .22 caliber 1911 styled pistol from them and they do have some interesting products to take a look at.
Then I saw a red tip on one of their Chiappa Rhino Revolvers which caught my eye since I was not aware that Chiappa was making an Airgun version of their Rhino. Well as it turns out they are hoping to be shipping both an Airsoft version and Steel BB version around spring time and from what I can tell there will be two finishes, a kind of Gold Satin finish and also a Back finish version. As is with a lot of revolvers these days they will be shell loading which will help them look the part of a real steel Chiappa Rhino Revolver.
Looking forward to getting my hands on one when they come out in Spring this year!
Here we go again, another round of SHOT Show videos brought to you direct from Replica Airguns!
As always I like to start off with a Teaser Video with a few quick clips of some of the new products I had the opportunity to take a look at at this years SHOT Show 2020 Las Vegas.
I will be rolling out Interview Videos as quickly as I can edit them and put them together for the following Airgun Related companies:
Sig Sauer
Umarex
Crosman - Velocity Outdoors
ASG
Air Venturi
Chiappa
So sit back and enjoy this years Replica Airguns SHOT Show 2020 Las Vegas Teaser Video!
Type: Paintball Gun. Manufacturer:Umarex - T4E. Model:T4E TR50 Materials: Metal & Polymer. Weight: 726 grams (1.6 pounds). Barrel: Smooth bore. Power Source: 1x12 gram CO2. Action: Revolver - Double action only trigger. Ammo Type: .50 Caliber Paintball or Rubber Ball. Ammo Capacity: 6 Rounds x 5 magazines. FPS: 360.
Trigger Pull: The trigger pull on Umarex T4E TR50 .50 Caliber Paintball Revolver is double action only but not very long with a very different feel than I am use to. The best way to describe it is kind of lumpy, it starts out a bit firm and then eases off a lot just before it releases. Like climbing a hill and then coasting down the otters side. I will have to see how it feels when it’s all loaded up with CO2 and Paintballs and actually shooting at a target.
Build Quality: The build quality of the Umarex T4E TR50 .50 Caliber Paintball Revolver is good overall. It is a mostly plastic build with some metal parts where they need to be internally. It is essentially two plastic halves held together by screws with the few actual mechanical working external parts. You have the trigger with it’s working trigger safety, the removable magazine and magazine release and of course the quick puncture CO2 screw knob. The hammer is internal. The Umarex T4E TR50 .50 Caliber Paintball Revolver is not very heavy but it does feel really solid in the hand.
Expected fairly high fps power of 360 with .50 caliber paintballs, a bit too high for your average paintball field but perhaps powerful enough to discourage an intruder?
Lots of mounting option for accessories like a tac light, laser or other sighting option with it’s upper and lower picatinny rail setup.
Quick CO2 pierce system so you can leave a CO2 in it ready to go any time with no worries about CO2 leaking out.
Working Trigger Safety.
Comes with 5 total magazines you can preload ready for use.
Super non-complicated design. Once loaded with CO2 and Paintballs all you need to do is hit the CO2 knob and then pull the trigger.
Build quality feels good, the gun is fairly beefy but not overly heavy or hard to hold.
Cons:
Mostly all plastic build.
Sights do not have white dots on them and are not adjustable.
Do not expect a lot of shots per CO2. Will find out when I do my Field Test Shooting Review.
Comments:
The Umarex T4E TR50 .50 Caliber Paintball Revolver is an interesting Paintball gun, overseas versions are marketed as the HDR50 which stands for “Home Defense Revolver”, while the North American version is marketed as the TR50 or “Training Revolver”. This is mainly because in the Europe most countries are not allowed to own real handguns but can own “Self Defense handguns”. In North America as most people are well aware, in the US real handguns are very easy to obtain and can be used for self defense. Just across the border here in Canada we can not really purposely have on hand anything that we plan to use as a weapon for self defense so the Umarex T4E TR50 .50 Caliber Paintball Revolver is marketed as a Training Revolver. What’s the difference? Not much, our North American 360 fps version is a lot like the 7.5 joule German version in terms of power but you can also get a more powerful 11 joule version in the UK. All that said, the Umarex T4E TR50 .50 Caliber Paintball Revolver at least here in Canada is made and marketed as a Paintball gun but on the field may be too powerful? What you decide to do with it is up to you!
Another Field Test Shooting Video Review coming for the Replica Airguns Sea Can Indoor Airgun Shooting Range! In todays Shooting Review I test out the Schofield No. 3 CO2 BB-Pellet Revolver using both 4.5mm 5/1 grain Steel BB’s and .177 Caliber 6.9 grain Lead Pellets to see how well they perform in velocity and accuracy. As always I use a brand new CO2 for my velocity testing and for reference the temperature during my testing in the Sea Can was 23 degrees Celsius or 73 degrees Fahrenheit. For my accuracy portion of the shooting test I use a rested and seated shooting position shot 30 feet away from my fresh paper targets.
Starting off with the velocity or power potion of my Field Test Shooting Video for the Schofield No. 3 CO2 BB-Pellet Revolver. I first used the 4.5mm Steel BB shells and shot 3 rounds through my Chronograph averaging 369 fps. I then loaded up the Schofield No. 3 CO2 BB-Pellet Revolver with pellet shells and again placed three .177 caliber lead pellets through my Chrony and got a very similar result with an average of 361 fps. Keep in mind the lead pellets where 6.9 grain versus the steel BB’s at only 5.1 grain, so the lead pellets will be carrying more raw energy at the point of impact even though they where going just a tad bit slower than the steel BB’s.
In terms of accuracy both rounds performed about the same shooting at my paper target 30 feet away. Since the Schofield No. 3 CO2 BB-Pellet Revolver has a 6 round cylinder I shot 6 sounds for each test, 6 steel BB’s and then 6 lead pellets. I also changed the targets for each type of ammo between reloading. I found the Schofield No. 3 CO2 BB-Pellet Revolver shot fairly close to the bullseye, l but with both the Steel BB’s and lead pellets I got one outlier that spread out my groupings significantly, the other 5 rounds where all close being about 2 inches apart? Perhaps it was a bad or misshaped round, or maybe even me ;) I did notice the lead pellets seemed to have a really nice 4 round group out of the 6 that all fell within the bullseye. Hard to really say if BB’s or pellets performed better than the other one at least in my testing.
Overall the Schofield No. 3 CO2 BB-Pellet Revolver shot well for me, the trigger is nice and short and light making placing your shots easy, of course since it is a single action only trigger you kind of need to reset yourself between every shot which can effect groupings just a bit. Since the barrel is not rifled with no danger of damaging the rifling, you can really shoot what ever ammo type you feel like shooting or have on hand and since Schofield No. 3 CO2 BB-Pellet Revolvers get about the same speed and accuracy then it really doesn’t matter that much at the end of the day!
Type: BB/Pellet air revolver. Manufacturer/Distributor: Bear River. Model: Schofield No. 3 Materials: Mostly metal with plastic grips. Weight: 2.4 pounds. (1089 grams) Barrel: 7 inch (178mm) smooth bore barrel. Propulsion: 12 gram CO2. Action: Revolver, single action only. Ammunition Type: 4.5mm steel BB's and .177 Cal. Pellets. Ammunition Capacity: 6 rounds. FPS: 445fps.
Trigger Pull: The trigger pull on the single action only Schofield No. 3 CO2 BB-Pellet Revolver is what you would expect from a pistol of this design. Like the Colt Single Action Army the trigger pull is very short, light and crips, perfect for taking your time and getting a precise shot on target. You will of course have to cock the hammer manually before each shot ao no real action shooting.
Accuracy: I have not tested the Schofield No. 3 CO2 BB-Pellet Revolver in the Replica Airguns Sea Can Indoor Airgun Range but plan to get to it shortly. I will test out both 4.5mm Steel BB’s and some .177 caliber lead Pellets and see how the different ammo types effect both power and accuracy. Keep in mind the Schofield No. 3 CO2 BB-Pellet Revolver has a smooth bore barrel but I am pretty sure pellets will still perform well at 30 feet away.
Build Quality: The Schofield No. 3 CO2 BB-Pellet Revolver is built a lot like the Webley MK VI .455 CO2 Shell Loading Revolver line, perhaps even made in the same factory in Taiwan? The Schofield No. 3 CO2 BB-Pellet Revolver is pretty much an all metal construction other than the plastic grips and any internal seals. The fit and finish is excellent with a great overall weight in the hand. The pistol grips is a lot like what you have with the Colt Single Action Army pistol but the Schofield No. 3 CO2 BB-Pellet Revolver is a lot more front end heavy because of its beefy barrel.
Realism: In terms of replicating a real steel Schofield No. 3 CO2 BB-Pellet Revolver for sure looks and feels that part. The reassessed barrel and well hidden CO2 screw don’t give anything away that the Airgun version is not the real deal. But as with all of these shell loading Airgun Revolvers, the shells are actually closer to a .380 Caliber in diameter rather than a 45 which is what the real steel Schofield No. 3 CO2 BB-Pellet Revolver would be designed for.
If you are like a bulky revolver with good weight to it then the Bear River Schofield No. 3 is it.
Can shoot Steel BB’s or Pellets since it comers with both shell types.
Recessed barrel.
Well concealed CO2.
Shell loading design that loads from the back so no need to remove shells if you wish not to.
Single Action Only hammer and trigger action feel good, nice and light with short take-up and release.
Fairly discreet safety location right behind the hammer so easy to get at.
Super easy to load, pellet shells can even be reloaded with shells in the gun if you are using the pellet shells.
Really like the Nickel Finish on this gun.
Can get simulated Ivory grips for it if you prefer that look.
Cons:
Sights are not adjustable.
Warning instructions on side of the frame.
Barrel is not rifled for pellet use?
Only a Single Action Only Hammer and Trigger but true to the style of the gun.
Comments:
Yet another classic shell loading CO2 BB Revolver, and again the more the merrier in my option! I like that you get 12 shells with our kit version, 6 removable shells for 4.5mm Steel BB’s and 6 removable shells for .177 caliber Pellets. The Schofield No. 3 CO2 BB-Pellet Revolver is for sure a hefty revolver but the pistol grip is not super large so even people with smaller hands should not have a problem shooting the Schofield No. 3 CO2 BB-Pellet Revolver. The real problem is deciding which Shell Loading Airgun Revolver to buy now since we have so many to choose from… Classic or modern, nickel or black, or perhaps weathered?
My Table Top Review for the Schofield No. 3 CO2 BB/Pellet Revolver:
Here we have three very different products I Unbox and Preview for everyone. A Spring Piston multi-shot .177 Caliber Pellet Rifle, a single action BB/Pellet revolver that’s not a Colt! And a really nice looking Semi Auto Blank Pistol in a Chrome finish.
Let’s start with the Air Venturi TR5 Spring Piston 5-shot .177 Caliber Pellet Rifle. I think this is a really well thought out Air Rifle. It’s “almost a Bullpup” in design but it does actually load in front of the trigger just a bit, that said most of the spring piston is behind the trigger setup making it really compact yet with a longer than normal barrel compared to regular Break Barrel Spring Piston Air Rifles. The Air Venturi TR5 Spring Piston 5-shot .177 Caliber Pellet Rifle also has a side lever cocking mechanism along with a 5 round auto indexing magazine which makes it much quicker to cock and reload for fast follow-up shots, again compared to a standard Break Barrel Air Rifle, not to mention no barrel droop! The Air Venturi TR5 Spring Piston 5-shot .177 Caliber Pellet Rifle has a claimed fps of up to 500 so we are getting the max amount of velocity possible for our Canadian laws without making it a regulated firearm and requiring a PAL license. And by the way the Air Venturi TR5 Spring Piston 5-shot .177 Caliber Pellet Rifle does come in both a Lime Green and all Black version just in case you are not a fan of the Lime Green finish I show in this video.
Moving onto the Schofield No. 3 BB/Pellet 6 Shot Revolver Replica, if you like single action revolvers then take a look at the Schofield No. 3 BB/Pellet 6 Shot Revolver Replica. It’s a lot more bulky than a Colt Single Action Revolver and also has that top Break design that makes reloading quick and easy. The version we are selling inner Replica Airgun Online Store is the kit version that comes with 6 BB shells and 6 pellet shells so you can take your pick on ammo types. The barrel is not rifled so Steel BB’s will not hurt the Airgun and since pellets are skirted they do not need a rifled barrel to fly straight and true. You can expect around 445 fps for the Schofield No. 3 BB/Pellet 6 Shot Revolver Replica.
The question comes up often about which Airgun to buy. Customers are wondering when they are looking at a specific Airgun and they see several similar products but from different companies, are they the same gun and if so which one should they decide to buy?
One of the biggest Airgun suppliers out there is for sure KWC, their BB and Airsoft guns are redistributed through companies like Umarex, Crosman, Sig Sauer, ASG, Gletcher and more. Often times the companies that redistribute KWC Airguns hold licensing agreements with real gun manufacturers like Smith & Wesson, Glock, Colt, Beretta, Sig Sauer, Taurus to name a few… KWC makes the Airguns in their Taiwanese factory but they are not allowed to put a real gun manufacturer license on the Airguns they distribute directly so KWC distributed Airguns will generally be all black.
I have also seen companies like Umarex distribute a new KWC Airgun that I have not seen yet from KWC, I believe KWC works with these big name Airgun companies directly and will build a new gun or variation of an existing KWC Airgun for them and give that Company an exclusive for a period of time. KWC will eventually regain the rights to sell that Airgun model directly after 6 months to a year.
Now that you know a little bit more on how it all works let’s get back to whether you should buy a KWC branded Airgun or other Brands same Airgun. It really comes down to I would say three factors. Do you want a Licensed version of the Airgun you are buying? Is there a price difference? Which gun is available to buy when I am ready to buy?
When you buy the Licensed version of the KWC Airgun redistributed through a third part Airgun Company you will often get a lot more writing on the Airgun than just the Gun Manufacturers name. Warning information comes to mind and does not look all that attractive on the slide where it is usually found in bright white lettering. If you like a cleaner look and don’t mind the lack of licensing then the KWC distributed version will generally be all back, nice and clean looking.
You would think buying the KWC Version that is sold more directly to the end customer would be the less expensive of the options because less hands are involved in the selling process. This is not always true, it is more about supply and demand, if more people want the cleaner looking KWC version but it’s harder to get ahold of than the price of the KWC version may actually be higher than say the Umarex or Crosman version. So shop around if price is the deciding factor as the guns are going to be mechanically the same with just some slight cosmetic differences between them.
Lastly, availability maybe what eventually leads you to buy a KWC version over an Umarex, or Crosman or Sig version since if the gun is not in stock well you may have limited options and so the one in stock is going to be perhaps your only option! Don’t feel like you got short changed, again these guns are virtually all the same at the end of the day no matter if you buy it from KWC, Umarex, Crosman, Sig Sauer, ASG, Gletcher or whomever.
I’ve reviewed a lot of the Single Action Army Revolvers to date in a variety of 4.5mm Steel BB and .177 caliber lead pellet shooting versions but so far I have not reviewed any 6mm Airsoft versions, until now!
In this Field Test Shooting Video Review I test out the Umarex Legends Wildcard 45 CO2 Airsoft Revolver to see what the actual real world fps is and also shoot at a paper target 30 feet down range to see what kind of accuracy I can get from it.
Starting with my Chronograph test. I placed 6 shots using my Umarex Legends Wildcard 45 CO2 Airsoft Revolver through the Chronograph and averaged them out getting a result of 342 fps. Not bad considering Umarex claims only 335 fps. I was using .20 gram plastic Airsoft BB’s with a brand new CO2 and the indoor temperature was 22 degrees Celsius or about 70 degrees Fahrenheit which is a fairly neutral temperature for testing a CO2 Airgun.
Next I loaded up my Umarex Legends Wildcard 45 CO2 Airsoft Revolver this time with .32 gram plastic Airsoft BB’s and shot the full 6 round cylinder on my paper target 30 feet away using a rested seated position. 5 of the rods all shot within about 3 inches while one came outside of this just a bit. The Umarex Legends Wildcard 45 CO2 Airsoft Revolver shot really well center on the target and since there are no sighting adjustments or hop-up adjustments this is good news!
I’m not really sure if a six shot single action only revolver is really going to be your best option for an Airsoft battle but hey who am I to say. The Umarex Legends Wildcard 45 CO2 Airsoft Revolver does have about the right fps for close quarter shooting and shoots on target at least at 30 feet or more so in those regards it’s just fine. Low ammo capacity, not so quick reloading and having to cock the hammer for each shot could be a limiting factor but if the old west cowboys could clear a room in seconds with these six shooters then why not give it a go!
In this Update Video we take a look at some BB and Airsoft pistols I have already reviewed but in a slightly different form factor. They are all Umarex Legends pistols but two of them (The P.08 and M712) are WWII Special Editions versions with that aged weathered look to them.
The Umarex Single Action Army Wildcard .45 is in 6mm Airsoft which I have so far not review in a Single Action Army Revolver so not only will I be showing you this one up close, but I will be doing a followup Field Test Shooting video for it shortly.
Here are some basic specifications on these three Airguns:
Umarex WWII Limited Edition M712 Full Auto Blowback BB Pistol
Type:BB Pistol Manufacturer:Umarex Model:WWII Limited Edition M712 Materials: Full Metal Weight: 1424 grams (3.15 pounds) Barrel: Smoothbore Power Source: CO2 Action: Semi and Full Auto Ammo Type: 4.5mm BBs Ammo Capacity: 18 Rounds FPS: 360
Umarex WWII Limited Edition P08 CO2 Blowback BB Pistol
Type:BB Pistol Manufacturer:Umarex Model:WWII P08 Materials: Full Metal Weight: 808 grams (1.7 pounds) Barrel: Smoothbore Power Source: CO2 Action: Semi and Full Auto Ammo Type: 4.5mm BBs Ammo Capacity: 21 Rounds FPS: 300
This year at SHOW Show 2019 Bob from ASG had a lot to show me so make sure to watch the full Interview Video for all the details and information.
Bob and I first go over a new ASG CZ Airsoft Pistol called the Shadow 2 kind of like a modernized SP-01 Shadow. The ASG CZ Shadow 2 is a competition stile pistol with adjustable sights and trigger and will come in both CO2 and Green Gas magazine options.
Next up Bob showed me the CZ75 SP01 ACCU Shadow with some special edition features like: Ergonomic anodized aluminum grips with grip tape, match style high sights, oversized slide release and ambidextrous safety and a tunable anodized aluminum trigger.
ASG being the exclusive partner with ICS had some new ICS Pistols to show us. First up was the Airsoft ICS XPD, a compact Gas Blowback System that will come with shorter compact magazines and extended magazines that will hold more green gas. Both Gas magazines will feature a new valve system called the Revo system.
If you like the feel of a 1911 but perhaps want something a bit more modern then checkout the New ASG Korth PRS Airsoft Pistol, you can even put real 1911 grips on it!
Not new to ASG this year is the CZ Scorpion Evo 3 A1 but ASG has enhanced this Airsoft rifle by working with a designer to adding an M-Lok Handguard, Magwell Grip and Fore Grip that will be a three part system you can customize.
Last Bob showed me around the CQR Hera Arms Airsoft Rifle that is a collaboration of ASG, Hara Arms, ICS. It will come in standard Mosfet and Triple-S (Smart Shooting System).
Looking forward to getting my hands-on some of these new ASG
This may be a bit confusion to some of you but Crosman has done a bit of a rebrand and is now going by the name of Velocity Outdoor. This is because Crosman has been acquiring more and more products over the years that are not necessarily airgun related and felt that putting all the brands under the name Velocity Outdoor made more sense from a company stand point. Of course in this video we are going to focus in on the Crosman Products within Velocity Outdoor.
So what’s new? Well an even better Crosman DPMS SBR! How can you make the Crosman DPMS SBR even better? By creating an updated or version 2 called the Bushmaster MPW. It comes in two tone black and false dark earth with a shorter hadnguard yet it keeps it’s barrel leith by extending the barrel right to the end of the mock suppressor. Tis can also swap out the but stock with any AR but stock and the Bushmaster MPW comes with a red dot sight. Internally the Bushmaster MPW and the Crosman DPMS SBR are the same.
Some of you may remember the Crosman Night Stalker CO2 Pellet Rifle? That product was retired years ago but Crosman has used the name in a new CO2 BB Pistol called the Night Stalker. The Crosman Night Stalker Pistol has a built in guide rod styled laser, has blowback operation along with a stick magazine. This should be a fun plinker with its laser sight.
Going even further back to the old Crosman 357 days, this revolver styled CO2 air pistol just seems to live on and on being revamped just a little each time by Crosman. Now you can get it in their Triple Threat package. Basically it’s the same Crosman 357 frame that comes with three barrels you can swap out as needed. You get a three inch snub nosed barrel, a six inch barrel similar to the Vigilante and then an eight inch Dirty Hairy styled barrel. Who says you can’t have it all?
My Field Test Shooting videos for blank guns are pretty basic! I can’t test for accuracy since there is no bullet hitting a target and similarly since there is no bullet I can not test the velocity or feet per second power. SO what is there really left to test?
I guess will the blank gun I am testing fire when I pull the trigger? That’s all there is to really test. You may ask why even make a Field Test Shooting Video for a blank gun if you can’t test accuracy and power. I’ll tell you why… Because it’s just fun and it looks good on camera :)
So watch my YouTube video of me popping of some .380 caliber blanks with my ROHM RG-89 .380 Caliber Blank Revolver inside the Sea Can Airgun Shooting Range.
Type: Blank Revolver. Manufacturer: ROHM (RÖHM). Model:RG-89 Materials: Mostly Metal. Weight: 1.45 pounds (658 grams). Barrel: Front firing designed for attaching a flare adaptor. Propulsion: Gun powder. Action: Single & double action. Ammunition Type: 9mm / .380 caliber crimped. Ammunition Capacity: 6 rounds. FPS: N/A.
Trigger Pull: The trigger pull on the ROHM RG-89 .380 Caliber Blank Revolver in single action is fairly light weight with virtually no take up at all as you would expect from a revolver. The double action trigger pull is much heavier with a smooth release. Mechanically the trigger feels really solid.
Accuracy: NA.
Build Quality: The overall build quality for the ROHM RG-89 .380 Caliber Blank Revolver is excellent, being German made its built to last and the fit and finish is typical German quality. There are steel parts where they need to be like in the barrel, pins, screws and reenforcing parts, the rest of the gun is generally made out of a zinc alloy otherwise know as pot metal with only the moulded grips being made out of plastic.
Realism: The ROHM RG-89 .380 Caliber Blank Revolver is not an exact replica of any given gun in production as this would make importing it into Canada even more difficult, but it is styled after a Snub Nosed type Revolver. As for looking like and working like a real gun, the ROHM RG-89 .380 Caliber Blank Revolver looks and sounds as loud as a real gun, of course with the exception of the dangerous bullet coming out of the barrel!
All metal gun with reenforced steel in some areas.
Front firing gun.
Large caliber makes a bigger bang.
Higher 6 shot capacity over RG-59.
Chrome (Silver) finish is very nice.
Also like the moulded grips on the Chrome version.
Comes with Flare Adaptor & Cleaning Rods.
Comes in a nice foam lined plastic hard shell case.
Right now Rohm is the only blank gun brand we can get in Canada.
Cons:
Double Action trigger pull is a bit heavy.
Have to make sure you only shot them where you will not get in trouble. Very loud!
Expensive due to them being harder to get and in high demand in Canada.
Comments: I think the ROHM RG-89 .380 Caliber Blank Revolver especially in the Chrome (Nickel) version is one of the nicest looking ROHM Blank guns we stock. The additional size over say a ROHM RG-59 makes it feel a lot more beefy in the hand, you also get the extra 6th 9mm / .380 caliber blank with the larger cylinder of the ROHM RG-89 .380 Caliber Blank Revolver. Anther bonus with the Chrome or Nickel version is that you get moulded grips that again I feel looks and fells better in the hand. Along with the ROHM RG-88, the ROHM RG-89 .380 Caliber Blank Revolver is one of my Top ROHM Picks!
My Full Video Review for the ROHM RG-89 .380 Caliber Blank Revolver:
