If you have not already watched my Preview video for both of these Airsoft pistols then make sure to watch that video for details and specifications along with some nice tight shots of each Airsoft gun.
Another multi gun Field Test Shooting Review, in this Indoor Sea Can Field Test Shooting Video I test out the KWC M1911 and PT92 Full Blowback CO2 Airsoft Pistols. I first place 5 6mm .25 gram plastic Airsoft BB’s through my Chronograph to find out what the real world velocity is for each Airsoft Pistol and then I perform my accuracy test where I shoot multiple rounds into a paper target 30 feet down range to see how close of a grouping I can get with each Airgun. I use a seated and rested shooting position to eliminate as much human factor as possible. By the way is used a brand new 12 gram CO2 and the temperature was 25 degrees Celsius (77 degree Fahrenheit) inside the Airgun Sea Can Shooting Range.
Starting with the KWC M1911 CO2 Blowback Airsoft Pistol I averaged 351 fps with the fastest shot being 353 and the slowest shot 345, so very consistent for sure! Accuracy for the KWC M1911 CO2 Blowback Airsoft Pistol could have been a bit better, I had to adjust my aim point to just under the bottom rings and even so the KWC M1911 wanted to shoot high, I was able to get around a 5 inch 10 shot grouping but was hoping for a bit better.
Next I tested out the KWC PT92 CO2 Blowback Airsoft Pistol which does have a full auto option. For the velocity portion of my Field Test the KWC PT92 did shoot a bit after than the MWC M1911 getting an average fps of 388 with the fastest shot hitting 396 and the slowest shot at 383 so again very consistent performance. Since the KWC PT92 CO2 Blowback Airsoft Pistol is capable of full auto shooting I decided to shoot 5 rods on my paper target to get a base accuracy and this resulted in a bit of a lateral spread fairly close to the bullseye about 4-5 inches apart. I then did a mag dump and as expected pretty much sprayed 6mm Airsoft BB’s all over the place but most shot a bit high and to the left probably because of the blowback recoil action.
The KWC M1911 and PT92 CO2 Blowback Airsoft Pistols are both classic Airguns and great options if your looking for a 1911 or Beretta styled Airgun to add to your collection without all the markings and white writing on them.
This is a combined Filed Test Shooting Video for the KWC 2022 NBB - 24/7 NBB - 24/7 Blowback CO2 BB Pistols. I already made an update video for these KWC Steel BB Pistols since they are slightly different version I have not covered in any video beforehand.
As per my typical Field Test Shooting Videos I first place 5 shots through my Chronograph to test out the real world fps of each gun. I then shoot 10 rounds on a paper target setup 30 feet away using a seated and rested shooting position. My ammo for this test was 5.1 grain zinc coated 4.5mm Steel BB’s for all airguns along within a brand new 12 gram CO2. The temperature in my indoor Sea Can Airgun Shooting Range was around 25 degrees Celsius (77 degrees Fahrenheit) for this test.
First up was the KWC 2022 NBB 4.5mm CO2 Steel BB Pistol with an average five shot fps of 347. The KWC 2022 NBB 4.5mm CO2 Steel BB Pistol was the least accurate of the three Airguns tested on this day getting about a 5-6 inch 10 shot grouping. I did notice when I went to edit the video that it did shoot a double shot on the first shot which lowered that first shot making the group a bit larger. This may have been as a result of pulling the trigger with the safety on right before which probably loaded a round into the barrel followed by the second pull loading a second BB into the barrel.
I then tested out the KWC 24/7 NBB 4.5mm CO2 Steel BB Pistol which was by far the most powerful Airgun tested out of the three hitting a top fps of 452 with a five shot average of 420 fps! The KWC 24/7 NBB 4.5mm CO2 Steel BB Pistol was also fairly accurate getting a nice 2 inch 10 shot grouping, slightly to the left and just under the bullseye. Nothing wrong with that!
The last KWC 4.5mm Steel BB pistol for the day was my KWC 24/7 Blowback CO2 4.5mm Steel BB Pistol. The only only blowback single action shooter out of the bunch. As expected from a blowback CO2 Airgun the fps was lower averaging just under 300 fps (298 to be precise). The surprise of the day was the accuracy from the KWC 24/7 Blowback CO2 4.5mm Steel BB Pistol was the best out of this test group getting really close to a 1 inch grouping very well centered just a tad to the right but with near perfect elevation.
Depending on what you are going for, all of these Airguns are great choices. If you want ultimate power perhaps go for the KWC 24/7 NBB 4.5mm CO2 Steel BB Pistol with its 450+ fps, if you want accuracy and realism then I would suggest the KWC 24/7 Blowback CO2 4.5mm Steel BB Pistol with its full blowback action and excellent accuracy.
This Field Test Shooting Review for the Daisy Powerline 340 Spring BB Pistol is a lot different from most of my other shooting video reviews mainly because the Daisy Powerline 340 Spring BB Pistol is not a CO2 powered BB Pistol like pretty much every other 4.5mm Steel BB pistol I have ever tested. There are way more 6mm Airsoft spring pistols but when it comes to actual 4.5mm BB Pistols they are not very common. The Daisy Powerline 340 Spring BB Pistol is Kind of like the pistol version of the Daisy Red Ryder BB Rifle…
So let’s get right into the nitty gritty on how the Daisy Powerline 340 Spring BB Pistol performed in the Replica Airguns Indoor Sea Can Airgun Shooting Range. Starting off with the feet per second velocity for the Daisy Powerline 340 Spring BB Pistol Daisy claims around 240 fps. shooting about 8 shots through my chronographs with standard 5.1 grain 4.5,, steel BB’s I was able to get an average of just over 180 fps, the Daisy Powerline 340 Spring BB Pistol was super consistent shooting all shots between 181 and 189 fps.
I then proceeded to place 10 shots on my paper target setup 30 feet down range shooting from a rested portion with a sand bag up front supporting my hadbn’s and a stool to sit on in the back. The Daisy Powerline 340 Spring BB Pistol did shoot a bit low and to the left but all 10 shots grouped within 3 inches of each other, actually a bit better than I was expecting from a low cost BB Pistol like this. If I was shooting at a pop can and adjusted my aim point a bit I would have hit the can 10 out of 10 times which is about as good as you can ask for a plinker like this.
The best way I can describe the Daisy Powerline 340 Spring BB Pistol is the pistol equivalent of the Daisy Re Ryder in that it shoots 4.5mm Steel BB’s has a high capacity BB reservoir that holds lots of BB’s and you are required to cock the spring for each shot rather than use CO2 for power. This makes for an over low cost Airgun but like the Daisy Red Ryder it is a lot fo fun to shoot at the end of the day. The Daisy Powerline 340 Spring BB Pistol has a surprisingly good trigger and at the end of the day shot really consistently for me.
Type: BB Pistol. Manufacturer: Daisy Model:Powerline 340. Materials: Mostly metal construction. Weight: 1 Pound (454 grams). Barrel Length: 4-5 inches Total Length: 8.5 inches. Propulsion: Spring Action: Single action only. Ammunition Type: 4.5mm steel BB’s. Ammunition Capacity: 13/200 round magazine. Max FPS: 240 fps.
Trigger Pull: The Daisy Powerline 340 Spring BB Pistol has a single action only trigger. You will have to pull the slide back for each shot as this motion draws the spring back and also cocks the hammer. The trigger pull is fairly decent with about a quarter inch of take-up followed by a light predictable release. There will not be any action shooting since the trigger is not double action and the fact that the slide must be pulled back for each shot.
Accuracy: So far I have not made my Field Test Shooting Video for the Daisy Powerline 340 Spring BB Pistol but I did take it outside for some good old plinking to see how it would perform causally shooting in the yard. The Daisy Powerline 340 Spring BB Pistol shot a bit harder than I was expecting it to and I was even able to hit targets a good 50 or so feet away but did have to account for some trajectory arch. Accuracy seemed good in general without a lot of need to adjust my aim point as the sights seemed well centered out of the box which is good since they are not adjustable.
Build Quality: The build quality of the Daisy Powerline 340 Spring BB Pistol is nothing exciting as it is mostly plastic with a metal barrel and perhaps a few other internal metal parts. Being that the Daisy Powerline 340 Spring BB Pistol is mostly plastic it only weighs in at about a pound but feels good in the hand. Everything feels pretty solid on the airgun with good overall fit and finish.
Realism: In terms of realism the Daisy Powerline 340 Spring BB Pistol is a good replica of a Beretta 92 in terms of looks and size comparison. Other than the open slide area that exposes the inner barrel being shorter than a real steel Beretta (probably to accommodate the internal spring) the Daisy Powerline 340 Spring BB Pistol looks very close to a Beretta 92. Moving parts include the slide, hammer, magazine release and slide catch release which is actually the safety. Even the magazine is drop out and near full size. I also like that there are no perceivable screw holes which is usually the case with these types of low cost all plastic Airguns when they are basically two halves slapped and screwed together.
Pros:
Pretty decent replica of a Beretta 92 in general.
For an inexpensive Airgun it has a lot of working parts that make it more realistic.
Very low cost to buy and operate, no CO2 required (Under $40 in Canada Store right now).
Has a recessed barrel for added realism.
Single action only trigger is not overly long or heavy.
Lots of ammo stored in the internal hopper so no need for a lot reloading.
Safety actually looks like part of the gun built into the slide catch release.
Full size dropout magazine.
Weight and feel of gun are pretty good considering so much plastic.
Cons:
Not super high in the fps department.
Need to cock the slide for every shot so not going to be an action shooter.
Made in China.
Comments: The Daisy Powerline 340 Spring BB Pistol is one of those low cost yet kind of fun BB guns that as long as you don’t have super high expectations you will get a ton of fun out of for very little cost. At about $40 Canadian with a bit more for some 4.5mm steel BB’s you are ready to shoot all day long. I was a bit surprised at how decent of a little BB gun the Daisy Powerline 340 Spring BB Pistol is. It looks real enough, has a decent build quality to it, actually shoots pretty good with a nice trigger and for such a low cost airgun it has a lot going for it like lots of working parts and even a removable full size magazine that doubles as a 200 round hopper with 13 round internal magazine. I don’t think anyone will be disappointed buying the Daisy Powerline 340 Spring BB Pistol and it would make a perfect first BB gun for a younger person looking to get started out in the sport.
My Vimeo Table Top Review for the Daisy Powerline 340 Spring BB Pistol:
Type: Pellet Revolver. Manufacturer: Gamo Model:PR-776. Materials: Mostly metal construction. Weight: 2.2 Pounds (1 kg). Barrel Length: 6 inches Total Length: 11.5 inches. Propulsion: CO2 x1 Action: Revolver single and double action. Ammunition Type: .177 caliber pellets. Ammunition Capacity: 8 rounds per magazine. Max FPS: 400+ fps.
Trigger Pull: The Gamo PR-776 CO2 .177 Caliber Pellet Revolver has your traditional revolver single and double action trigger setup. In double action, the trigger is going to be a bit longer and heavier but it feel fairly smooth with no real friction points and I would consider it to have a medium trigger pull. When you cock the hammer back placing the Gamo PR-776 CO2 .177 Caliber Pellet Revolver in single action, the trigger pull becomes very short with virtually no take-up at all and the weight of the trigger is very light allowing for more accurate shots.
Accuracy: Make sure to watch my Field Test Shooting video for the Gamo PR-776 CO2 .177 Caliber Pellet Revolver where I test out the velocity and accuracy in the Replica Airguns Indoor Airgun Shooting Range. In summary the Gamo PR-776 CO2 .177 Caliber Pellet Revolver shot a little bit hotter than claimed at just over 400 fps using around 7 grain lead pellets. In terms of accuracy with a total of 16 shots the grouping spread out to around 4 inches but I am pretty sure a different pellet choice may have made a difference.
Build Quality: The build quality of the Gamo PR-776 CO2 .177 Caliber Pellet Revolver is pretty good overall. It is mostly all metal with the exception of the grips of course, Fit and finishes looks good, everything feel snug adn tight with the exception of the pistol grips. I feel like the grips could easily move out of place and get caught on something. This is not a problem when shooting, more so when in a holster. The Gamo PR-776 CO2 .177 Caliber Pellet Revolver feels good in the hadn't, nice and solid and with a good weight to it.
Realism: The Gamo PR-776 CO2 .177 Caliber Pellet Revolver is a decent looking Airgun in the style of a traditional revolver, I wouldn’t say it’s an exact replica of any specific revolver in production but it does tick off all the boxes in terms of looking realistic. The weight and feel for now and the Gamo PR-776 CO2 .177 Caliber Pellet Revolver also has a recessed barrel and hidden CO2 crew. The only real giveaway would be the cylinder size as it is a bit smaller than expected and of course is chambered for .177 caliber pellets.
Pros:
Good power over 400 fps using actual lead pellets.
Quicker reloading over shell loading revolvers
More shots per magazine reload, 8 versus 6.
Comes with two metal 8 round magazines.
Traditional single and double action trigger.
White dot front sight with fully adjustable rear sight.
Good weight and feel to it.
Fit and finish look good.
Recessed barrel for realistic looking barrel opening.
Should be able to use a dovetail type scope mount for adding on a red dot or magnified scope.
Cons:
Not a fan of the loose pistol grip setup to access the CO2.
Was hoping to get a bit tighter grouping but may have been a pellet choice issue.
Comments: It was nice reviewing the Gamo PR-776 CO2 .177 Caliber Pellet Revolver as it was a bit different then most of today shell loading revolvers. I like that the Gamo PR-776 CO2 .177 Caliber Pellet Revolver still offered a realistic looking cylinder that the shell loading revolvers have but with the moon clip style magazines that allow for quick adn easy reloading of 8 rounds at a time. The velocity or power of the Gamo PR-776 CO2 .177 Caliber Pellet Revolver was even a bit high than Gamo claims using PBA Platinum pellets since Gamo claims 400 fps using these 5.1 grain lead pellets. My testing with closer to 7 grain pellets yielded fps up and over 400 fps. All the Gamo PR-776 CO2 .177 Caliber Pellet Revolver needs is to be just a little bit more accurate but I feel this may simply be more of a pallet choice, once you find a pellet the Gamo PR-776 CO2 .177 Caliber Pellet Revolver likes I am pretty sure it will deliver accurate shots.
My Table Top Review for the Gamo PR-776 CO2 .177 Caliber Pellet Revolver:
Type: Break Barrel Pellet Pistol. Manufacturer: Gamo Model:P900 IGT. Materials: Mostly plastic build with some internal metal parts. Weight: 1.28 Pounds (580 grams). Barrel Length: 6.25 inches Total Length: 12.52 inches. Propulsion: Gas Piston (IGT) Action: Break barrel single action trigger. Ammunition Type: .177 caliber pellets.. Ammunition Capacity: 1 round. Max FPS: 400 fps using PBA Platinum pellets (about 5 grain).
Trigger Pull: The trigger on the Gamo P900 IGT .177 Caliber Pellet Pistol uses what Gamo calls their SAT or Smooth Action Trigger system. Overall the single action only trigger feels pretty good, not super light but also not overly heavy. The Gamo P900 IGT .177 Caliber Pellet Pistol has a short take up with a very predictable release point. I found it fairly easy to use and shoot with precision.
Build Quality: The Gamo P900 IGT .177 Caliber Pellet Pistol is mainly made out of plastic, pretty much everything is plastic including the trigger but there will be internal metal parts where they are required. That said the Gamo P900 IGT .177 Caliber Pellet Pistol feels well made with fairly heavy plastic throughout. The Gamo P900 IGT .177 Caliber Pellet Pistol is not super heavy but feels hefty enough in the hand.
Realism: The Gamo P900 IGT .177 Caliber Pellet Pistol is not a replica of any specific pistol in production and has a very modern look to it. I would say it looks more like an airgun than a real gun and that’s exactly what is’t supposed to be so this is not a negative in this case.
Pros:
Reasonable price for a target pistol.
Performed well, can easily get .5 inch groupings from 30 feet away.
No need for CO2.
Inert Gas Technology (IGT) has less vibration and no reduction to power over time.
Fiber optic front sight.
Adjustable rear sight for windage.
Inexpensive to shoot.
Made in Spain.
Ambidextrous design.
Reasonable trigger pull.
Cons:
Not supper powerful. Shot around 300 fps with standard lead pellets.
A bit hard to cock because of such a short barrel.
Rear sight is only adjustable for windage and not elevation.
Comments: The Gamo P900 IGT .177 Caliber Pellet Pistol is a nice overall low cost target pistol with a very modern look and Gas Piston technology. In terms of performance the Gamo P900 IGT .177 Caliber Pellet Pistol tested well for me shooting accurately with a consistent 300 fps velocity which is what you want in a target pistol, consistency over raw power. I like the overall design and look, the Gamo P900 IGT .177 Caliber Pellet Pistol feels good in the hand and easy to shoot, the trigger is not overly light but is also not too heavy by any means. My only complaint is the cocking effort involved because of such a short barrel and I also noticed a bit of a stickiness with the cocking effort but I have a feeling this may break in over time or perhaps a drop of oil in the hinge area may do the trick. If you want a modern looking target pellet pistol with good performance than the Gamo P900 IGT .177 Caliber Pellet Pistol will for sure fit the bill!
My Table Top Review for the Gamo P900 IGT .177 Caliber Pellet Pistol:
For this Field Test Shooting Video Review of the Gamo P900 IGT .177 Caliber Pellet Pistol I test the power and accuracy to determine what the real world (fps) Feet Per Second velocity and how tight of a grouping I can get for 30 feet down range.
For the power portion of my Indoor Filed Test I shot five RWS 6.9 grain lead pellets through my Chronograph with an average velocity of 305 fps. This resulted in a 1.43 foot pound energy rating. My slowest shot out of the Gamo P900 IGT .177 Caliber Pellet Pistol was 289 fps and the fastest shot was 311 fps. Gamo claims the Gamo P900 IGT .177 Caliber Pellet Pistol can achieve 400 fps but this would be using lighter alloy pellets like PBA Platinum pellets.
Next I setup at a fresh paper target 30 feet down range and proceeded to place 8 shots into the target using a seated and rested shooting position. My first shot was a bit high as I was getting use to the trigger but the following 7 shots all grouped within about 3/4 of an inch, 6 of them all within a half inch of each other so the Gamo P900 IGT .177 Caliber Pellet Pistol is for sure capable of 1/5 inch groupings from a 30 foot distance. The placement of the shots grouping was a little bit high and to the left. since the Gamo P900 IGT .177 Caliber Pellet Pistol has an adjustable trigger for windage I could easily center the grouping right in the middle. In terms of elevation there is no adjustment so I would need to manually adjust this on the fly depending on the distance I was shooting at.
The Gamo P900 IGT .177 Caliber Pellet Pistol performed very well for me, the power is what you would expect for a target pistol, I would not recommend the Gamo P900 IGT .177 Caliber Pellet Pistol for any pest control. Accuracy was very good and I feel once getting use to the trigger you shoudl be able to get shots all within a 1/2 inch at 30 feet. The trigger is not super light but by no means is it heavy, the take-up is short with a predictable release, I found the trigger to work well overall. My only complaint is cocking the Gas Spring as the barrel is short and it does take some effort to do this, especially getting it started off, once you get past the first little bit it does get easier to cock. If you’re looking for a nice accurate target pellet pistol at a relatively inexpensive price point then for sure consider the Gamo P900 IGT .177 Caliber Pellet Pistol.
Type: BB Rifle. Manufacturer: Crosman. Model: R1 AR. Materials: Metal & plastic. Weight: 6 pounds (2.7 kilograms). Length: 26.25 / 29.25 inches (Stock closed / extended). Propulsion: 12 gram CO2 dual cartridges. Action: Blowback - single action only. Ammunition Type: 4.5mm steel BB's. Ammunition Capacity: 25 rounds. FPS: 430fps. Rate of Fire: 1400 rounds per minute in full auto
Trigger Pull: The trigger pull on the Crosman R1 CO2 Blowback BB Machine Gun is single action only since the charging handle must be cocked first before you can shoot it. The trigger is short and fairly light as you would expect from an AR type trigger action. The real fun happens with the Crosman R1 CO2 Blowback BB Machine Gun when you switch it over to full auto mode and with just one pull and hold of the trigger you empty the 25 round magazine in mere seconds.
Build Quality: The Crosman R1 CO2 Blowback BB Machine Gun is well made all around. Weighing in at 6 pounds without any add on accessories it feel solid and well built. There is a lot of metal going on inside and out of this rifle but keep in mind the top and bottom receiver are plastic with metal parts where they need to be like in the internals, pretty much all the working parts are metal, the magazine is full metal, the buffer tub is metal, charging handle, selector switch, magazine release, bolt release, trigger and of course the barrel is metal.
Realism: The Crosman R1 CO2 Blowback BB Machine Gun is about as real as you are going to get in a CO2 Blowback AR/M4 styled Airgun. You can even take it apart and split the top and bottom receivers like the real steal version. The blowback action gives you some recoil but more importantly offers a true single action trigger and of course the full auto ability we all love. Almost all the working parts work like they would on a real AR / M4 other than the forward assist which is moulded into the receiver.
Pros:
Super realistic working M4/AR 4.5mm BB Rifle just like the otters Crosman Rifles in this lineup.
Full blowback operation with both semi and full auto shooting, can feel the blowback operation rocking the gun.
Great weight and feel to it.
Almost everything works exactly like the real steel version. (Charging handle, dust cover, bolt release, magazine release, selector switch…)
Duel CO2 full metal drop out magazine that holds the 25 4.5mm steel BB’s as well.
Adjustable and customizable AR butt stock.
Included red dot sight and ability to add pop-up iron sights.
Lots of rails of mounting additional cool hardware.
Removable flash hider that uses standard threading.
Cons:
Receiver is plastic but well made and does not compromise feel or weight since there is lots of metal throughout this gun.
No iron sights included.
Comments:
The Crosman R1 CO2 Blowback BB Machine Gun is really pretty much the same as the Crosman DPMS SBR and Crosman MPW with more or less Cosmetic changes. Like the Crosman MPW the Crosman R1 has an AR compatible Rear stock and pistol grip, the Crosman R1 CO2 Blowback BB Machine Gun is the only Crosman AR Full Auto CO2 BB Rifle that has the ability to change out the flash hider, you can even put a mock suppression or in it if you choose to. No matter which of the Crosman AR Full Auto CO2 BB Rifles you chooses to get they are mechanically every similar and share most of the same parts. I would say the Crosman R1 CO2 Blowback BB Machine Gun is the most customizable to date but they are all fantastic Air Rifles!
My Table Top Video of the Crosman R1 CO2 Blowback BB Machine Gun:
My systems setup for a more powerful airgun as I was shooting .22 caliber lead pellets with about 11-12 foot pounds of energy. Direct hits passing through the 3/4 inch cut outs had no problem laying down the metal paddles and resetting the paddles was a lot easier than I though it would be even way back 50 feet.
I did not have my Sig Sauer Virtus PCP .22 Caliber Air Rifle perfectly sighted in so I did have to aim low and to the left which made it a bit harder dropping the plates but I did manage to get the job done at least for providing a decent test video fo the Rx Target Systems for the purposes of this video.
Make sure to not only watch my Field Test Shooting video included in this post but also checkout my Rx Target Systems Preview Video where I show it up and close and also go into more details on the Rx Target Systems and how modular and versatile it really is.
I want to thank David Bitkowski from Rx Target Systems for providing me with this sample unit to share with the Replica Airguns community. This video is only a Preview video as I wanted to get the RX Target System out there before I follow up with my actual Table Top and Shooting Videos for it.
For now here are some of the key points I want to get out to everyone:
Mission: Rx Target Systems are meant to bridge the gap between firearms and airguns. They allow high precision shooting on a reactive, three- dimensional, rugged target that can be carted around in a back pack. What makes Rx Target Systems unique is that it is a system. It is so modular and adaptable with interchangable faceplates and paddles. Rx Target Systems are not going to break or get dented or dissembled on the range as many of the lighter gauged steel targets on the market today vs today’s high powered airguns.
Modular
One base allows interchange of faceplates for different target configurations
One threaded axel allows interchange of paddle from 10 gauge to 3/8 inch-thick paddles
Portable
Mount it on a shelf indoors
Mount it on a sawhorse outdoors
Carry it in a backpack or duffle bag- its 10 pounds
Rugged
Solid steel design
Faceplates from 10 gauge to ¼ inch thick
3-Dimensional
Faceplate is offset from paddles
Clipping the aperture does not guarantee a score
Intentions of target configurations
Standard 1 inch bulls.- represents kill zone of many small game at 30 yards, great for sighting in prior to the hunt. Also is ¼ scale of bull used in rapid fire pistol when shot from 8.3 meters. (25 meters distance/100mm bull)
1.2 inch bulls- represents the 4-10 ring of the NRA 10 meter air rifle target. Gears the shooter to consistently hitting the “black” of that target on paper
AAFTA style- represents common kill zones found in American Airgun Field Target Assosciation using 1.5”, 1”, ¾", ½", and 3/8”.
WFTF style- represents common kill zones found in World Field Target Federation using 15mm, 25mm, and 38mm apertures
10-15- Inspired by customer request, uses 10mm and 15mm apertures. High-Precision shooting.
In this SHOT Show Las Vegas 2020 Interview Video Scott takes us through a range of new products from Air Venturi.
Scott and I talk about the Air Venturi TR5 and how it came about to fill the hole the Baikal MP-61 left behind. We also talk a look at some new Air Rifles, a pumper called the Butterfly with a super cool linkage based system that makes pumping a lot easier. A PCP side lever cocking Air Rifle that I’m not even sure has a name yet but will be available in .177 .22 and .25 caliber pellet for around $299 US.
The only Air Venturi replica we looked at is a new Springfield Armory under lever Spring Piston Air rifle modeled after the M1A. Last up Scott went showed us how the Bada Bang targeting system is shaping up and looks to be almost ready for production.
Here we go again, another round of SHOT Show videos brought to you direct from Replica Airguns!
As always I like to start off with a Teaser Video with a few quick clips of some of the new products I had the opportunity to take a look at at this years SHOT Show 2020 Las Vegas.
I will be rolling out Interview Videos as quickly as I can edit them and put them together for the following Airgun Related companies:
Sig Sauer
Umarex
Crosman - Velocity Outdoors
ASG
Air Venturi
Chiappa
So sit back and enjoy this years Replica Airguns SHOT Show 2020 Las Vegas Teaser Video!
I have not officially done a Field Test Shooting Video for the Umarex Legends CO2 BB Lever Action Cowboy Rifle other than my quick outside shooting test where I simply shot a bunch of rounds at some pop cans just to see how the Umarex Legends CO2 BB Lever Action Cowboy Rifle would work for me and it did perform well during that test.
Jumping ahead to a little while later when I went to make my Official Field Test Shooting Video for the Umarex Legends CO2 BB Lever Action Cowboy Rifle. I found it was not performing well at all, shooting well under the 410 claimed fps closer to 200 fps which was a surprise since it seemed to do a lot better for me on my previous test. I even changed out the CO2 but still did not get any better results. I racked this up to maybe being a defective gun and so I went about getting my hands on another Umarex Legends CO2 BB Lever Action Cowboy Rifle.
Guess what? Same thing with rifle number two. Very poor fps, again almost half of the claimed rated velocity. So at this point I decided I was goring to make the Field Test Shooting Video for the Umarex Legends CO2 BB Lever Action Cowboy Rifle and let the results speak for themselves… I also thought it would be fun to compare it to the Classic 1938 Daisy Red Ryder BB Gun since I figured they would both get similar fps and accuracy and be rather comparable at the end of the day.
I do have to say that the Umarex Legends CO2 BB Lever Action Cowboy Rifle did make me eat my words and I am happy it did since I really like the Umarex Legends CO2 BB Lever Action Cowboy Rifle and wanted it to do well!
Usually I state all there results for My Field Test Shooting Videos here in the written article but I kind of feel it is best if you just watch this one from start to finishes since the video result s did turn out to really surprise me in the end.
We had a lot of great new Airguns that I reviewed this year at Replica Airguns. Some of them really stood out to me and so I made a video showing my Favorite Replica Airgun Picks of 2019. Of course there where many other Airguns that could has just as easily made this video but I had to draw the line somewhere and pick the ones that in my opinion where the best of 2019. Make sure to watch my Vimeo video where I go into some more details on why I liked each Airgun.
Below is a list of the top Replica Airgun Picks of 2019:
In a way I have already Field Tested the Air Venturi TR5 .177 Caliber Pellet Rifle, well at least in the Baikal version. The Air Venturi version is pretty much a knock of of the Baikal IZH MP-61 which not only look a lot alike but also performed very similarly for me, checkout my Baikal YouTube Video Review for comparison. All that said we can not get Baikal products here in North America anymore so it’s great that Air Venturi has recreated a very similar product for us to have in Canada and the US.
Moving on to the Field Test Review for the Air Venturi TR5 .177 Caliber Pellet Rifle, I first placed 5 shots through my Chronograph to see if the Air Venturi TR5 .177 Caliber Pellet Rifle did in fact shoot around 500 fps and in fact I was able to get all 5 shots up and over 500 fps averaging around 513 fps. Still within our Non-regulated firearm laws here in Canada since we where still under the 4.2 foot pound energy limit using 6.9 grain pellets.
As mentioned before when I shot the Baikal IZH MP-61 I was able to get very similar results but I did have an optical scope on the Baikal IZH MP-61 as compared to the Air Venturi TR5 .177 Caliber Pellet Rifle where I just used the open sights. In my opinion the Air Venturi TR5 .177 Caliber Pellet Rifle is good value for your money offering a unique design with excellent performance and getting as much power out of a pellet rifle as you can get here in Canada without requiring a firearms license.
Pick one up in our Canada or US Online Replica Airguns stores!
Type: Paintball Gun. Manufacturer:Umarex - T4E. Model:S&W M&P9 M2.0 Materials: Metal & Polymer. Weight: 763 grams (1.7 pounds). Barrel: Smooth bore. Power Source: 1x12 gram CO2. Action: Semi-Automatic with blowback action. Ammo Type: .43 Caliber Paintball or Rubber Ball. Ammo Capacity: 8 Rounds. FPS: 290.
Trigger Pull: The trigger pull on Umarex T4E S&W M&P9 M2.0 .43 Cal. Paintball Pistol feels a lot like a double action trigger mainly because when you pull the trigger the inner barrel travels backwards into the magazine which seals off the barrel form the magazine so less CO2 is wasted going it not the magazine and also placing a paintball round in the barrel. This does make the trigger a little bit longer and heavier than a single action trigger. I believe the internal hammer/striker is engaged from the blowback action.
Build Quality: The build quality of the Umarex T4E S&W M&P9 M2.0 .43 Cal. Paintball Pistol is really very good, metal parts are where you would expect them, the slide, slide catch, barrel, magazine and most internal parts giving the Umarex T4E S&W M&P9 M2.0 .43 Cal. Paintball Pistol a nice near 2 pounds (1.7 pounds) of weight with the magazine in which makes the Paintball version a little heavier than the real steal version (1.54 pounds) but once the real steal version is loaded with a full mag this may even out a bit. The Umarex T4E S&W M&P9 M2.0 .43 Cal. Paintball Pistol does have a polymer frame but again this is normal with todays modern guns and helps keep the weight down. Fit and finish is also very good!
Realism: The Umarex T4E S&W M&P9 M2.0 .43 Cal. Paintball Pistol is a near perfect replica of the real steel S&W M&P9 M2.0 Pistol, from the fully licensed markings to the large .43 caliber diameter barrel. If you placed the Paintball version side by side with the real steel version I doubt you could tell them apart unless you start inspecting it really close up and working the action. You will find that the slide cycle distance is a bit shorter than it would be meaning that when the side catch is engaged the slide does not go as far back as it the real 9mm S&W M&P9 M2.0. Field stripping the Umarex T4E S&W M&P9 M2.0 .43 Cal. Paintball Pistol will requires some tools and pin removal.
Type: BB/Pellet air revolver. Manufacturer/Distributor: Bear River. Model: Schofield No. 3 Materials: Mostly metal with plastic grips. Weight: 2.4 pounds. (1089 grams) Barrel: 7 inch (178mm) smooth bore barrel. Propulsion: 12 gram CO2. Action: Revolver, single action only. Ammunition Type: 4.5mm steel BB's and .177 Cal. Pellets. Ammunition Capacity: 6 rounds. FPS: 445fps.
Trigger Pull: The trigger pull on the single action only Schofield No. 3 CO2 BB-Pellet Revolver is what you would expect from a pistol of this design. Like the Colt Single Action Army the trigger pull is very short, light and crips, perfect for taking your time and getting a precise shot on target. You will of course have to cock the hammer manually before each shot ao no real action shooting.
Accuracy: I have not tested the Schofield No. 3 CO2 BB-Pellet Revolver in the Replica Airguns Sea Can Indoor Airgun Range but plan to get to it shortly. I will test out both 4.5mm Steel BB’s and some .177 caliber lead Pellets and see how the different ammo types effect both power and accuracy. Keep in mind the Schofield No. 3 CO2 BB-Pellet Revolver has a smooth bore barrel but I am pretty sure pellets will still perform well at 30 feet away.
Build Quality: The Schofield No. 3 CO2 BB-Pellet Revolver is built a lot like the Webley MK VI .455 CO2 Shell Loading Revolver line, perhaps even made in the same factory in Taiwan? The Schofield No. 3 CO2 BB-Pellet Revolver is pretty much an all metal construction other than the plastic grips and any internal seals. The fit and finish is excellent with a great overall weight in the hand. The pistol grips is a lot like what you have with the Colt Single Action Army pistol but the Schofield No. 3 CO2 BB-Pellet Revolver is a lot more front end heavy because of its beefy barrel.
Realism: In terms of replicating a real steel Schofield No. 3 CO2 BB-Pellet Revolver for sure looks and feels that part. The reassessed barrel and well hidden CO2 screw don’t give anything away that the Airgun version is not the real deal. But as with all of these shell loading Airgun Revolvers, the shells are actually closer to a .380 Caliber in diameter rather than a 45 which is what the real steel Schofield No. 3 CO2 BB-Pellet Revolver would be designed for.
If you are like a bulky revolver with good weight to it then the Bear River Schofield No. 3 is it.
Can shoot Steel BB’s or Pellets since it comers with both shell types.
Recessed barrel.
Well concealed CO2.
Shell loading design that loads from the back so no need to remove shells if you wish not to.
Single Action Only hammer and trigger action feel good, nice and light with short take-up and release.
Fairly discreet safety location right behind the hammer so easy to get at.
Super easy to load, pellet shells can even be reloaded with shells in the gun if you are using the pellet shells.
Really like the Nickel Finish on this gun.
Can get simulated Ivory grips for it if you prefer that look.
Cons:
Sights are not adjustable.
Warning instructions on side of the frame.
Barrel is not rifled for pellet use?
Only a Single Action Only Hammer and Trigger but true to the style of the gun.
Comments:
Yet another classic shell loading CO2 BB Revolver, and again the more the merrier in my option! I like that you get 12 shells with our kit version, 6 removable shells for 4.5mm Steel BB’s and 6 removable shells for .177 caliber Pellets. The Schofield No. 3 CO2 BB-Pellet Revolver is for sure a hefty revolver but the pistol grip is not super large so even people with smaller hands should not have a problem shooting the Schofield No. 3 CO2 BB-Pellet Revolver. The real problem is deciding which Shell Loading Airgun Revolver to buy now since we have so many to choose from… Classic or modern, nickel or black, or perhaps weathered?
My Table Top Review for the Schofield No. 3 CO2 BB/Pellet Revolver:
Here we have three very different products I Unbox and Preview for everyone. A Spring Piston multi-shot .177 Caliber Pellet Rifle, a single action BB/Pellet revolver that’s not a Colt! And a really nice looking Semi Auto Blank Pistol in a Chrome finish.
Let’s start with the Air Venturi TR5 Spring Piston 5-shot .177 Caliber Pellet Rifle. I think this is a really well thought out Air Rifle. It’s “almost a Bullpup” in design but it does actually load in front of the trigger just a bit, that said most of the spring piston is behind the trigger setup making it really compact yet with a longer than normal barrel compared to regular Break Barrel Spring Piston Air Rifles. The Air Venturi TR5 Spring Piston 5-shot .177 Caliber Pellet Rifle also has a side lever cocking mechanism along with a 5 round auto indexing magazine which makes it much quicker to cock and reload for fast follow-up shots, again compared to a standard Break Barrel Air Rifle, not to mention no barrel droop! The Air Venturi TR5 Spring Piston 5-shot .177 Caliber Pellet Rifle has a claimed fps of up to 500 so we are getting the max amount of velocity possible for our Canadian laws without making it a regulated firearm and requiring a PAL license. And by the way the Air Venturi TR5 Spring Piston 5-shot .177 Caliber Pellet Rifle does come in both a Lime Green and all Black version just in case you are not a fan of the Lime Green finish I show in this video.
Moving onto the Schofield No. 3 BB/Pellet 6 Shot Revolver Replica, if you like single action revolvers then take a look at the Schofield No. 3 BB/Pellet 6 Shot Revolver Replica. It’s a lot more bulky than a Colt Single Action Revolver and also has that top Break design that makes reloading quick and easy. The version we are selling inner Replica Airgun Online Store is the kit version that comes with 6 BB shells and 6 pellet shells so you can take your pick on ammo types. The barrel is not rifled so Steel BB’s will not hurt the Airgun and since pellets are skirted they do not need a rifled barrel to fly straight and true. You can expect around 445 fps for the Schofield No. 3 BB/Pellet 6 Shot Revolver Replica.
