You’ve seen them all before but have you seen them in this exact configuration? All the Airguns I show off in this video are made by KWC and generally come in either Steel BB and or Airsoft versions along with non-blowback and blowback versions. You can even find most of them redistributed by other companies like Umarex, Cybergun, Gletcher, Crosman and others even licensed in some cases.
The versions I am showing today I have not review yet in these exact configuration and all of them are the KWC made and distributed unlicensed versions, so nice and clean with virtually none of that ugly white lettering on them…
In this Field Test Shooting Video I shoot the ASG CZ P-09 Threaded Barrel CO2 Blowback Airsoft Pistol in my indoor Sea Can Airgun Shooting Range to see what the actual velocity is and also see how well it will group shooting 10 Airsoft BB’s at a paper target 30 feet down range. I was using .25 gram Airsoft BB’s for my testing purposes with Propane Gas as my propellant. The temperature inside the Sea Can was around 26 degrees Celsius (79 degrees Fahrenheit).
I started off my Field Test Shooting video with the Chronograph portion of my test and placed 5 shots through my Chrony using a brand new 12 gram CO2 cartridge. I have to mention the fps consistency was very impressive with all five shots only varying within 6 fps of each other the slowest being 330 fps and the fastest test shot being 336 fps. My end 5 shot average fps was 33fps again using a .25 gram Airsoft BB.
I then loaded my ASG CZ P-09 Threaded Barrel CO2 Blowback Airsoft Pistol with 10 rounds for the accuracy portion of my test and was able to get all 10 shots within a nice 2 inch grouping. The shot placement was well centered left to right and a little bit high on target which I am sure could be adjusted for using the hop-up.
The ASG CZ P-09 Threaded Barrel CO2 Blowback Airsoft Pistol is a rally nice Airsoft pistol, it has a great trigger with a firm blowback action. The super consistent fps is pretty much exactly where you want it to be, just powerful enough to allow for Canada import but not too powerful for Airsoft gaming. The accuracy was also very good right out of the box so pretty much nothing to complain about in terms of performance. Another nice Airsoft product from ASG!
In this Field Test Shooting Video I shoot the Cybergun FN Herstal FNX-45 Tactical GBB Airsoft Pistol in my indoor Sea Can Airgun Shooting Range to see what the real world velocity is and also how well it will group shooting 10 rounds at a paper target 30 feet down range. I was using .25 gram Airsoft BB’s for my testing along with Propane Gas. The temperature inside the sea can was around 26 degrees Celsius (79 degrees Fahrenheit).
Because the Cybergun FN Herstal FNX-45 Tactical GBB Airsoft Pistol coms with both a shorter internal barrel and a screw on extended barrel designed to be hidden inside a mock suppressor I thought it would make sense to test both the short and long barrels to see what the fps difference would be. With the short internal barrel I shot 4 rounds and average 255 fps. I then added the longer barrel extension again shooting 4 rounds but this time I averaged 363 fps so a good 100+ fps faster with the longer barrel attachment added to the Cybergun FN Herstal FNX-45 Tactical GBB Airsoft Pistol.
For my accuracy portion of the testing I left the extended barrel on the gun but was a bit disappointed in my 10 shot grouping. The Cybergun FN Herstal FNX-45 Tactical GBB Airsoft Pistol did not get the tightest of groupings coming in at around 5 inches. It also shot a little bit to the right but vertically was fairly well centered. Perhaps changing up the barrels and lengths might make a difference?
I did really like the Cybergun FN Herstal FNX-45 Tactical GBB Airsoft Pistol, it has a really light trigger that is a bit hard to find the release point, the blowback action is crisp but not overly heavy. I’m pretty sure the Cybergun FN Herstal FNX-45 Tactical GBB Airsoft Pistol is a VFC product so the quality is bang on. Other than the grouping being a little bit spread out I really liked everything about the Cybergun FN Herstal FNX-45 Tactical GBB Airsoft Pistol.
Type: Blowback CO2 Airsoft Pistol. Manufacturer: ASG Model:CZ P-09 Threaded Barrel. Materials: Metal and polymer construction. Weight: 2.3 Pounds (1050 grams). Barrel Length: 4.4 inches (11.2 cm). Total Length: 9 Inches (22.9 cm). Propulsion: CO2 Action: Single and double action. Ammunition Type: 6mm plastic Airsoft BB’s. Ammunition Capacity: 25 round magazine. Max FPS: 376 fps.
Trigger Pull: The ASG CZ P-09 Threaded Barrel CO2 Blowback Airsoft Pistol has a single and double action trigger setup. Both feel pretty decent, the double action trigger pull is a little on the heavy side but you won’t really be shooting in double action all that much since the blowback action will cock the hammer between shots allowing for the vast majority of your shots to be single action which you will find are short and very light. There is a slight bit of take-up followed by a crisp very light release.
Accuracy: So far I have not made my Field Test Shooting Video for the ASG CZ P-09 Threaded Barrel CO2 Blowback Airsoft Pistol. Check back shortly for my upcoming Field Test Shooting Video for the ASG CZ P-09 Threaded Barrel CO2 Blowback Airsoft Pistol, until then the shooting results will remain a mystery but if this product is like otter ASG products it should produce good results for me .
Build Quality: The build quality of the ASG CZ P-09 Threaded Barrel CO2 Blowback Airsoft Pistol is what I would expect from an ASG Airgun. The materials used look good and have an excellent finish to them. Slide wiggle is very minimal and all the mechanical parts feel solid and responsive. You will find metal parts where you would expect them to be like in the slide, barrel components, magazine, slide catch release take-down leaver, safety, hammer, trigger, rear sight, magazine release and lots of other internal parts.
Realism: In terms of realism the ASG CZ P-09 Threaded Barrel CO2 Blowback Airsoft Pistol is an excellent copy of the real steel CZ P-09 with all the markings and licensing in all the right places. Mechanically everything works about the same including full field strip-ability and the ability to add a mock suppressor if you want to.
Pros:
Build quality feels really goods, lots of weight to this Airsoft Pistol.
Full length blowback action.
Accurate licensed CZ P-09 replica.
Trigger pull is nice in both single and double action.
Picatinny rail for adding accessories like a tac light or laser.
Double stack full size drop out Metal Magazine holds the CO2 and 25 Airsoft BB’s
Comes with black and orange tips depending on what you prefer to use.
Easy to see white dot front and back sights.
CO2 powered makes it easy for Canada import.
Easily Filed Strippable.
Tips are easy to remove for the addition of a mock compensator.
Adjustable Hop-up.
Cons:
Sights don’t seem to be adjustable.
Controls are not all ambidextrous.
Comments: The ASG CZ P-09 Threaded Barrel CO2 Blowback Airsoft Pistol is another great addition to the ASG CZ line of Airguns. You can now get CZ Replica Airguns from ASG in a variety of models including the CZ 75D, CZ 75 P-07 Duty, CZ 75D Compact and of course the CZ P-09 in Airsoft, Steel BB and even Pellet firing ammunition. I would say the ASG CZ P-09 Threaded Barrel CO2 Blowback Airsoft Pistol is probably one of the most realistic in terms of looks, action and functionally but no matter what your preferences is, ASG will have something for you in the CZ lineup of Airguns for sure!
My Vimeo Table Top Review for the ASG CZ P-09 Threaded Barrel CO2 Blowback Airsoft Pistol:
Type: GBB Airsoft Pistol. Manufacturer: Cybergun Model:FN Herstal FNX-45 Tactical. Materials: Metal and polymer construction. Weight: 1.8 Pound (820 grams). Barrel Length: 4.8 inch (12.2 cm). Total Length: 8.9 Inches (22.6 cm). Propulsion: Green gas or propane Action: Single and double action. Ammunition Type: 6mm plastic Airsoft BB’s. Ammunition Capacity: 25 round magazine. Max FPS: 380 fps.
Trigger Pull: The Cybergun FN Herstal FNX-45 Tactical GBB Airsoft Pistol has a single and double action trigger setup. Both feel pretty good with a surprisingly light double action trigger pull, the blowback action will cock the hammer between shots allowing for the vast majority of your shots being single action which you will find are short and very light. There is a little bit of take-up followed by a crisp light release.
Accuracy: So far I have not made my Field Test Shooting Video for the Cybergun FN Herstal FNX-45 Tactical GBB Airsoft Pistol. Keep posted for my upcoming Field Test Shooting Video for the Cybergun FN Herstal FNX-45 Threaded Barrel GBB Airsoft Pistol, until then I can not really comment on the shooting results.
Build Quality: The build quality of the Cybergun FN Herstal FNX-45 Tactical GBB Airsoft Pistol feels really good, it has a nice weight to it and feels really solid in the hand. The materials used look good and have an excellent finish to them. There is just a bit of a slide wiggle but not excessive. You will find metal parts where you would expect them to be like in the slide, barrel components, magazine, slide catch release, take-down leaver, hammer and lots of internal parts.
Realism: In terms of realism the Cybergun FN Herstal FNX-45 Tactical GBB Airsoft Pistol is pretty much the spitting image of the real steel version with all the markings and licensing in all the right places. Mechanically everything works about the same including full field strip-ability with full ambidextrous controls.
Pros:
Build quality feels really good.
Full length blowback action.
Accurate licensed TFN Herstal FNX-45 Tactical replica.
Trigger pull is nice in both single and double action.
Picatinny rail for adding accessories like a tac light or laser.
Double stack full size drop out metal magazine holds the gas and 25 Airsoft BB’s
Comes with additional back-strap in smaller size for smaller hands.
White dot high rise front and back sights suitable for compensators.
Fully ambidextrous controls.
Easily Filed Strippable.
Tip is easy to remove for addition of a mock compensator.
Adjustable Bax Hop-up
Cons:
Sights are not adjustable.
Just a little bit of slide wiggle.
Comments: The Cybergun FN Herstal FNX-45 Tactical GBB Airsoft Pistol is a really great looking gun. The quality is on par with KWA and KJ Works in my opinion. I’m not sure who actually makes it as Cybergun is the license holder and distributer but I feel like the Cybergun FN Herstal FNX-45 Tactical GBB Airsoft Pistol is a step up from the standard KWC gun often used as the base. I look forward to testing out the Cybergun FN Herstal FNX-45 Tactical GBB Airsoft Pistol in the Sea Can indoor Airgun Shooting range to see how it performs. I’ll be testing with the short barrel and with the barrel extension installed to see what the fps difference is between the two.
My Vimeo Table Top Review for the Cybergun FN Herstal FNX-45 Tactical GBB Airsoft Pistol:
In this Table Top Preview video I take a look at two Blowback Airsoft Pistols one Distributed by Cybergun and the otters Distributed by ASG. Both are very similar in that they have threaded barrels which makes them much suppressor ready the big difference being that the ASG CZ P-09 is CO2 powered while the FN Herstal FNX-45 is Green Gas or Propane powered. IN this video I talk about the specifications and details and also show both Airsoft Pistols up nice and close.
I’ve had the Umarex Ruger 10/22 CO2 Pellet Rifle sitting around for a bit but just haven’t gotten around to reviewing it. When I saw it at SHOT Show a couple years back I was super excited about it probably because I though it was going to have internal blowback action making it function very much like the real steel 22LR Ruger 10/22. Once I finally got it in my hands I came to discover the Umarex Ruger 10/22 CO2 Pellet Rifle did not in fact have internal blowback and for the most part was a double action shooter. Yes you can work the Bolt Handle to cock the internal hammer making the Umarex Ruger 10/22 CO2 Pellet Rifle more of a single action trigger but you won’t be doing any action shooting this way, you’ll have to shoot in double action for that.
Getting on to my Field Test Shooting Review for the Umarex Ruger 10/22 CO2 Pellet Rifle this is how it went! As always a placed 5 rounds through my Chronograph to see what the real world fps was. Umarex claims with the detuned Canada version I was testing right around 450 using light weigth alloy pellets which are generally going to be around 5 grains. I like using lead pellets so I went with some 6.9 grain RWS lead pellets and was able to get a decent average fps of 420. (Keep in mind the US version is claimed to get around 650 fps using standard lead pellets). The temperature was around 24 degrees Celsius or 75 degrees Fahrenheit in my indoor Sea Can Airgun Shooting Range so not overly hot but a bit on the warmer side.
Next I setup a fresh paper target 30 feet down range and load up a full 10 round magazine and emptied it into the target shooting from a seated and rested position. I decided to shoot the Umarex Ruger 10/22 CO2 Pellet Rifle in single action for this test requiring me to charge the bolt handle before each shot. I was impressed to see a nice 10 round grouping with about half of my shots inside the bullseye and the other half just a little to the left, elevation was bang on and the grouping was just under an inch with all shots overlapping a bit.
I’m kind of thinking I may have prematurely written off the Umarex Ruger 10/22 CO2 Pellet Rifle because it didn’t have blowback action. I was expecting the trigger to be long and heavy but the trigger is actually really good even in double action mode so don’t let the lack of blowback action turn you off for the Umarex Ruger 10/22 CO2 Pellet Rifle at least in terms of trigger pull. Where the Umarex Ruger 10/22 CO2 Pellet Rifle excels in in consistency. It has the ability of being a real tac driver and as it’s based on the Ruger 10/22 platform I imagine there are all kinds of add-ons you can get for it. If you own the 22LR version and want to be able to shoot a 10/22 virtually anywhere for even less then the cost of 22LR ammo then consider picking up yourself one of the Umarex Ruger 10/22 CO2 Pellet Rifles in our Canada or US online Replica Airguns Stores.
Type: BB Rifle. Manufacturer: Crosman. Model: R1 AR. Materials: Metal & plastic. Weight: 6 pounds (2.7 kilograms). Length: 26.25 / 29.25 inches (Stock closed / extended). Propulsion: 12 gram CO2 dual cartridges. Action: Blowback - single action only. Ammunition Type: 4.5mm steel BB's. Ammunition Capacity: 25 rounds. FPS: 430fps. Rate of Fire: 1400 rounds per minute in full auto
Trigger Pull: The trigger pull on the Crosman R1 CO2 Blowback BB Machine Gun is single action only since the charging handle must be cocked first before you can shoot it. The trigger is short and fairly light as you would expect from an AR type trigger action. The real fun happens with the Crosman R1 CO2 Blowback BB Machine Gun when you switch it over to full auto mode and with just one pull and hold of the trigger you empty the 25 round magazine in mere seconds.
Build Quality: The Crosman R1 CO2 Blowback BB Machine Gun is well made all around. Weighing in at 6 pounds without any add on accessories it feel solid and well built. There is a lot of metal going on inside and out of this rifle but keep in mind the top and bottom receiver are plastic with metal parts where they need to be like in the internals, pretty much all the working parts are metal, the magazine is full metal, the buffer tub is metal, charging handle, selector switch, magazine release, bolt release, trigger and of course the barrel is metal.
Realism: The Crosman R1 CO2 Blowback BB Machine Gun is about as real as you are going to get in a CO2 Blowback AR/M4 styled Airgun. You can even take it apart and split the top and bottom receivers like the real steal version. The blowback action gives you some recoil but more importantly offers a true single action trigger and of course the full auto ability we all love. Almost all the working parts work like they would on a real AR / M4 other than the forward assist which is moulded into the receiver.
Pros:
Super realistic working M4/AR 4.5mm BB Rifle just like the otters Crosman Rifles in this lineup.
Full blowback operation with both semi and full auto shooting, can feel the blowback operation rocking the gun.
Great weight and feel to it.
Almost everything works exactly like the real steel version. (Charging handle, dust cover, bolt release, magazine release, selector switch…)
Duel CO2 full metal drop out magazine that holds the 25 4.5mm steel BB’s as well.
Adjustable and customizable AR butt stock.
Included red dot sight and ability to add pop-up iron sights.
Lots of rails of mounting additional cool hardware.
Removable flash hider that uses standard threading.
Cons:
Receiver is plastic but well made and does not compromise feel or weight since there is lots of metal throughout this gun.
No iron sights included.
Comments:
The Crosman R1 CO2 Blowback BB Machine Gun is really pretty much the same as the Crosman DPMS SBR and Crosman MPW with more or less Cosmetic changes. Like the Crosman MPW the Crosman R1 has an AR compatible Rear stock and pistol grip, the Crosman R1 CO2 Blowback BB Machine Gun is the only Crosman AR Full Auto CO2 BB Rifle that has the ability to change out the flash hider, you can even put a mock suppression or in it if you choose to. No matter which of the Crosman AR Full Auto CO2 BB Rifles you chooses to get they are mechanically every similar and share most of the same parts. I would say the Crosman R1 CO2 Blowback BB Machine Gun is the most customizable to date but they are all fantastic Air Rifles!
My Table Top Video of the Crosman R1 CO2 Blowback BB Machine Gun:
Here we are with yet another Crosman AR styled Full Auto Blowback CO2 BB Rifle and they just keep getting better, I say that lightly as even the first version the Crosman DPMS SBR still holds up to the 3 part lineup. It kind of has to since all three of them can be mixed and matched in terms of the uppers and lowers, magazines and I am sure most intern parts. Check out the Crosman DPMS SBR and the Crosman MPW for reference as I have made full table top and field test shooting videos for them already.
The purpose as always for my Field Test Shooting Videos is to find out how the airgun being reviewed performs in terms of velocity and accuracy, and if the ratings on paper end up being the same or close to the tested results. Crosman claims the Crosman R1 CO2 Blowback BB Machine Gun is capable of shooting 5.1 grain 4.5mm Steel BB’s at up to 430 fps. When I tested the Crosman R1 CO2 Blowback BB Machine Gun using my Chronograph averaging out 5 shots using a brand new set of CO2 cartridges I averaged 395 fps. Note the temperature in my Indoor Airgun Sea Can Shooting Range was about average at about 24 degrees Celsius or right around 75 degrees Fahrenheit. Comparatively I was able to get 405 fps from the Crosman DPMS SBR and around 385 fps with the Crosman MPW. Temperature may have beene slightly different on those testing days so that needs to be factored in.
Moving on to the accuracy portion of this Field Test Shooting Review for the Crosman R1 CO2 Blowback BB Machine Gun, I placed 10 semi auto shots on my paper target setup 30 feet downrange. I was using a rested and seated shooting position to help minimize human factor. I was able to get pretty much a 1 inch grouping with my 10 semi auto shots which was nit surprising as I have been able to get tight shot placement like this from the Crosman AR series before.
I then flipped the Crosman R1 CO2 Blowback BB Machine Gun semi auto selector switch to full auto and dumped the remaining 10 rounds into my paper target in full auto mode flowed by another full 25 round magazine again in full auto and the grouping only stretched out to about 2.5 -3 inches even with all the full auto vibrations and rocking around of the gun. Shot placement was a little bit high and to the left but this can easily be corrected using the red dot sight adjustments.
In summary the Crosman R1 CO2 Blowback BB Machine Gun performed a lot like the Crosman DPMS SBR and the Crosman MPW which makes since since all of them are virtually mechanically the same. In the end I think it really comes down to which of the Crosman AR type full auto BB rifles you like the look of since they areal very capable shooters. If you can’t decide then maybe get one of each :)
Starting with my Chronograph velocity testing for the Sig Sauer MCX ASP .177 Caliber CO2 Pellet Rifle, I used a brand new Sig branded 90 gram CO2 cartridge along with 6.9 grain RWS pellets. The temperature was 24 degrees Celsius (75 degrees Fahrenheit) in the Sea Can Indoor Airgun Shooting Range. Sig claims the Sig Sauer MCX ASP .177 Caliber CO2 Pellet Rifle to shoot up to 5.7 Joules. My Chrono testing resulted in an average fps of 418 with the 6.9 grain lead pellets which yielded a 3.7 Joule (2.7 foot pound) power output. I was not expecting 5.7 joules as that would have been closer to 600 fps using 6.9 grain pellets.
Next I setup a fresh paper target 30 feet down range and using seated and rested shooting position I placed 10 rounds into the target. The Sig Sauer MCX ASP .177 Caliber CO2 Pellet Rifle shot a decent 1.5 inch 10 round grouping but I am pretty sure I can get better results once I find the right pellet, I have found this especially to be true with Sig Air Rifles. My MCX Virtus was able to get 1/2 inch groupings at 50 feet once I found ammo it liked and my MPX also shot a bit tighter form 30 feet out with a different ammo selection. I then unload the remaining 15 rounds in to the target rapid fire, followed by another 30 round full magazine and the grouping only stretched out a little bit, closer to 2 inches. Shots placed on the target a little bit low and to the right but this can be easily corrected for consistent bullseyes using the fully adjustable sights.
The Sig Sauer MCX ASP .177 Caliber CO2 Pellet Rifle performed well for me in general, I did find that occasionally the belt did not index resulting in a misfire (no pellet fired) but the next pull of the trigger would index the belt resulting in a pellet firing, there where no jams and all rounds from the belt where fired. I am not sure why this happened as this did not happen to me with my other Sig Sauer Air Rifles. Perhaps I short triggered it a bit not getting a full belt index. I know many of you have been waiting for a Canadian version of the Sig Sauer MCX ASP .177 Caliber CO2 Pellet Rifle, now that we have them in the All Black Iron Sight Version and FDE Red Dot Version, make sure to get one as once we run out I am pretty sure we will no longer be able to get these Canada Import Legal Sig Sauer MCX ASP .177 Caliber CO2 Pellet Rifles.
Watch my Preview Video where I take a quick look at the Sig Sauer MCX CO2 Pellet Rifle and Crosman R1 Full Auto BB Rifle. Full Table Top and Field Test Shooting Videos coming soon.
First, I put four rounds through my Chrony Chronograph to see what the real world FPS would be, keep in mind I was using rubber balls rather than paintballs and the rubber balls are a little bit heavier and smaller in diameter than paintballs so this could bring the FPS down a bit compared to the slightly lighter paintballs. Using a brand new CO2, the Umarex T4E TPM1 .43 Cal. Paintball Pistol average 303 FPS which was higher than the claimed 290 FPS. Temperature inside my Indoor Sea Can Airgun Shooting Range was around 22 degrees Celsius or 72 degrees Fahrenheit.
Moving on to my accuracy testing as per my usual indoor field tests, I positioned myself 30 feet back from a fresh paper target and using a seated and rested shooting position I shot a full magazine (8 rounds) of rubber balls on target with the Umarex T4E TPM1 .43 Cal. Paintball Pistol. As mentioned before I was expecting around a 6 inch grouping and got pretty close to it getting closer to an 8 inch 8 shot grouping. The rubber balls did center well on the target all placing uniformly arounds the bullseye. If I was aiming at a human sized torso, I would have hit it with every shot from 30 feet away so good enough for me.
As expected I was able to get very similar and decent results compared to the other Umarex .43 Caliber CO2 Blowback Paintball Pistols I have already reviewed. I did want to mention some of shooting qualities you will find with the Umarex T4E TPM1 .43 Cal. Paintball Pistol. The trigger can feel a bit heavy especially using rubber balls as when you pull the trigger the inner barrel moves back and into the magazine going around the paintball and helping to seal off the CO2 from escaping. There is a bit of friction and I find the rubber paintballs seem to have more friction perhaps because the rubber grips more than the plastic surface on standard paintballs? This extra trigger friction or heaviness is really only noticeable when you are pulling the trigger slowly for accuracy testing but when shooting quickly as you would be more likely to do so in an actual training simulation, the trigger friction is all but forgotten about.
Type: Paintball Gun. Manufacturer:Umarex - T4E. Model:T4E TPM1 Materials: Metal & Polymer. Weight: 532 grams (1.2 pounds). Barrel: Smooth bore. Power Source: 1x12 gram CO2. Action: Semi-Automatic with blowback action. Ammo Type: .43 Caliber Paintball or Rubber Ball. Ammo Capacity: 8 Rounds. FPS: 290.
Trigger Pull: The trigger pull on Umarex T4E TPM1 .43 Cal. Paintball Pistol feels a lot like a double action trigger mainly because when you pull the trigger the inner barrel travels backwards into the magazine placing a paintball round in the barrel which seals the barrel with the magazine so less CO2 is wasted. This does make the trigger a little bit longer and heavier than a single action trigger. I believe the internal hammer/striker is engaged from the blowback action.
Build Quality: The build quality of the Umarex T4E TPM1 .43 Cal. Paintball Pistol is really very good, metal parts are where you would expect them, the slide, slide catch, barrel, magazine and most internal parts giving the Umarex T4E TPM1 .43 Cal. Paintball Pistol a decent overall weight with the magazine in which makes the Paintball version a little bit lighter than a real steel Glock 17 (624 grams - 22 ounces). The Umarex T4E TPM1 .43 Cal. Paintball Pistol does have a polymer frame but again this is normal with todays modern guns and helps keep the weight down. Fit and finish is also very good!
Realism: The Umarex T4E TPM1 .43 Cal. Paintball Pistol is not an actual replica of the the Glock17 Pistol, it is Umarex’s version of the Glock, Umarex does now the Glock lisense but perhaps they where not able to find an actual Glock 17 Paintball gun they could bring to market. The T4E TPM1 is designed to hold and feel similar to a Glock and for most real steel Glock owners the Umarex T4E TPM1 .43 Cal. Paintball Pistol would be close enough for training purposes. You will find that the slide cycle distance is a bit shorter than it would be meaning that when the side catch is engaged the slide does not go as far back as it the real 9mm Glock. Field stripping the Umarex T4E TPM1 .43 Cal. Paintball Pistol will requires some tools and pin removal.
Full Metal slide that locks back on the last shot.
All metal heavy full size drop out magazine adds some additional weight to the gun.
Good for Glock shooters looking for a similar training weapon.
Everything works pretty much like the real gun so again great as a training tool.
Easy to see yellow dot sights front and back.
Working trigger safety.
Fit and finish is excellent.
Magazine spring release really shoots the magazine out.
43 caliber barrel opening, adds to realism.
Cons:
White warning lettering stands out a bit too m much on the slide.
Magazine only holds 8 rounds, so you are going to need extra magazines for sure.
Blowback action is not full blowback, more like a typical half blowback BB gun.
Comments:
TheUmarex T4E TPM1 .43 Cal. Paintball Pistol is mechanically very close to the Umarex Walther PPQ M2 .43 Cal. Paintball Pistol and the Umarex T4E S&W M&P9 M2.0 .43 Cal. Paintball Pistol in how it functions as a Paintball Pistol so I expect all of them to shoot very similarly and that’s not a bad thing since previous versions I have tested so far have performed rather well for me in the Replica Airguns Sea Can Indoor Shooting Range. If you are a Glock fan than the Umarex T4E TPM1 .43 Cal. Paintball Pistol is about as close as you are going to get at least for now to a Glock Replica Paintball Pistol. As of right now being stuck at home, perhaps a Glock Paintball Trainer like the Umarex T4E TPM1 .43 Cal. Paintball Pistol using .43 caliber rubber ammo may just allow you to get some indoor shooting practice to keep your shooting skills up.
As always I like to test each gun out in the Replace Airguns Indoor Sea Can Airguns Range first placing 5 rounds through my Chronograph to find out the real world velocity of each test gun, then I shoot 10 rounds at a distance of 30 feet onto a paper target to see how tight of a grouping I can get shooting from a seated and rested position. When it come to full auto BB guns like the Umarex Legends M1A1 Blowback CO2 BB Machine Gun, I will usually switch up to full auto and dump the rest of the magazine to see if I can still sray on target with the remaining rounds.
For my Power or Velocity test I was using fairly new CO2, I had shot a full magazine a couple days before but the Umarex Legends M1A1 Blowback CO2 BB Machine Gun was all warmed up and ready to perform optimally. Umarex does state that it will shoot around 435 fps and with my 5 shot test I was able to confirm that with a 434 fps average. The temperature in the Sea Can was around 23 degrees Celsius or 73 degrees Fahrenheit.
For my accuracy test I setup a new paper target 30 feet downrange and proceeded to place 10 shots into it using the peep sights on the Umarex Legends M1A1 Blowback CO2 BB Machine Gun. Other than one slight flyer my 10 round grouping was around 3/4 of an inch and just a tad low of the bullseye but pretty close. I then switched over to full auto fun mode and with the remaining BB’s I unloaded all 20 rounds in about a half a second, or at least it seemed like that! The Umarex Legends M1A1 Blowback CO2 BB Machine Gun even in full auto mode with the trigger matted till the gun ran out I was still able to get a 2 inch grouping!
I’m a big fan of the Umarex Legends Series BB Guns and the Umarex Legends M1A1 Blowback CO2 BB Machine Gun may be my favorite out of all of them to date. The Thompson M1A1 is just such a stand out Machine Gun we all know from the Mob shows. Not only does the Umarex Legends M1A1 Blowback CO2 BB Machine Gun look the part but it performs I would have to say so far the best when it comes to Full Auto Machine guns at least from Umarex. I do have to say that the Crosman CO2 BB AR Series does not disappoint. That said if you are looking for a more classic BB Machine Gun that performs as good as it looks then my advice is grab yourself one of the Umarex Legends M1A1 Blowback CO2 BB Machine Gun and add it to your collection.
Type: Air Rifle / Machine Gun. Distributer: Umarex Model:Legends M1A1. Materials: Mostly Metal build. Weight: 7.75 pounds (3.5 kilograms) Barrel: 12 inches - smooth bore steel. Propulsion: 2x12 gram CO2. Action: Internal BoltBlowback single action. Ammunition Type: 4.5mm Steel BB's. Ammunition Capacity: 30 round full size drop out magazine. Max FPS: 435.
Trigger Pull: The trigger pull on the Umarex Legends M1A1 Blowback CO2 BB Machine Gun is single action only so you will need to charge the bolt for the first shot just like you would on the real steel Thompson M1A1, after that the blowback operation will charge the bolt which allows for semi and full auto shooting. Trigger pull is not very long or heavy.
Build Quality: The Umarex Legends M1A1 Blowback CO2 BB Machine Gun is pretty much all metal other than the stock and pistol grip. Pretty much everything that is black is going to be metal on this CO2 airgun. It weighs in at a hefty 7.75 pounds which is lighter than the real steel version by about 2 pounds but keep in mind the simulated plastic wood grips are a much lighter than real wood would be. Overall the fit and finish is really good, mechanical parts work well and seem to be well machined..
Realism: The Umarex Legends M1A1 Blowback CO2 BB Machine Gun is a 1 to 1 replica of the real steel World War II Thompson M1A1 Machine Gun and is very authentic looking with similar operation. Even the magazine holds 30 rounds just like the real steel Thompson M1A1. The blowback operation will give you a little bit of that shoulder tap but of course nothing like a 45 caliber M1A1. As expected in todays Replica Airguns the barrel is recessed to give it a larger opening and the CO2 screw is hidden well enough. I would like to see at least a real wood kit for the Umarex Legends M1A1 Blowback CO2 BB Machine Gun which would not lonely look even better but also increase the overall weight closer to the 10 pound real steel weight.
Yet another Classic Legends Replica Airgun from Umarex, maybe one of the best to date.
Mostly all metal design with good overall weight.
Semi and Full auto select-ability.
Dual CO2 design for increased shots and less cool down effect.
High capacity 30 round full size drop out metal magazine.
Umarex went with less rounds to get away from the double stay configuration of the 50 round Legends MP40 which was not always dependable.
Great looking replica of the real steel M1A1 in looks, operation and feel.
Internal bolt blowback will give a bit of recoil feedback feel.
Simulated wood looks very realistic.
Recessed barrel for added realism.
Cons:
Real wood hardware would have been cine and added it of additional weight. Maybe Umarex will offer this down the road?
Price is getting up there a bit but still worth it if you are an M1A1 fan, imagine what a real one would cost?
Going to eat up CO2 quickly in full auto mode but you can always switch over to semi auto.
Comments: Another great Legends product from Umarex, maybe even the best one so far. The only issues I had with the Umarex Legends MP40 was the double stack magazine feeding dependability with the 50 round double stack magazine not always feeding consistently. Umarex went back to a less aggressive closer to a single stack magazine on the Umarex Legends M1A1 Blowback CO2 BB Machine Gun which has a fewer rods but is expected to feed more consistently. I am looking forward to getting out and actually shooting the Umarex Legends M1A1 Blowback CO2 BB Machine Gun when I make my Field Test Shooting video. My advice right now with uncertainties about if and when we will get new inventory is buy now if you are in a position to as I am not sure how long they will last and when we will be able to get more stock.
My Vimeo Table Top Review of the Umarex Legends M1A1 Blowback CO2 BB Machine Gun:
I want to thank Drew from Tippmann Armory/Air Ordnance for sending me this unit for review. I have been wanting to get my hands one of these Air-Ordnance SMG 22 .22 Caliber Full Auto Pellet Machine Guns for several years now and super glad I happened finally :) I really don’t think there is any airgun out there like it. I am really hoping that we will be able to have this one in both our Canada and US Online Replica Airguns Stores.
So what exactly is the Air-Ordnance SMG 22 .22 Caliber Full Auto Pellet Machine Gun? It’s a PCP powered semi/full auto .22 caliber pellet firing Airgun and it is available in a Canada legal version that shoots just under 500 fps allowing it to be classified here in Canada as an unregulated Firearm. Unregulated Firearms do not require a license or registration and do not have to abide by the same rules that regulated firearms have to such as full auto limitations, magazine capacities and size limitations. So in other words if you want a full auto .22 caliber Machine gun here in Canada this is going to be your only option at least for now.
Some other cool features about the Air-Ordnance SMG 22 .22 Caliber Full Auto Pellet Machine Gun is the trigger setup, pull it light and quick and you get a single shot, pull and hold using medium force and you get full auto but not at a super high rate of fire. Press and hold the trigger down hard and you get full auto with a much faster rate of fire so you control the rate of fire by how hard you press the trigger down. Air-Ordnance SMG 22 .22 Caliber Full Auto Pellet Machine Gun also has an adjustment to set the maximum rate of full auto fire.
I want to thank David Bitkowski from Rx Target Systems for providing me with this sample unit to share with the Replica Airguns community. This video is only a Preview video as I wanted to get the RX Target System out there before I follow up with my actual Table Top and Shooting Videos for it.
For now here are some of the key points I want to get out to everyone:
Mission: Rx Target Systems are meant to bridge the gap between firearms and airguns. They allow high precision shooting on a reactive, three- dimensional, rugged target that can be carted around in a back pack. What makes Rx Target Systems unique is that it is a system. It is so modular and adaptable with interchangable faceplates and paddles. Rx Target Systems are not going to break or get dented or dissembled on the range as many of the lighter gauged steel targets on the market today vs today’s high powered airguns.
Modular
One base allows interchange of faceplates for different target configurations
One threaded axel allows interchange of paddle from 10 gauge to 3/8 inch-thick paddles
Portable
Mount it on a shelf indoors
Mount it on a sawhorse outdoors
Carry it in a backpack or duffle bag- its 10 pounds
Rugged
Solid steel design
Faceplates from 10 gauge to ¼ inch thick
3-Dimensional
Faceplate is offset from paddles
Clipping the aperture does not guarantee a score
Intentions of target configurations
Standard 1 inch bulls.- represents kill zone of many small game at 30 yards, great for sighting in prior to the hunt. Also is ¼ scale of bull used in rapid fire pistol when shot from 8.3 meters. (25 meters distance/100mm bull)
1.2 inch bulls- represents the 4-10 ring of the NRA 10 meter air rifle target. Gears the shooter to consistently hitting the “black” of that target on paper
AAFTA style- represents common kill zones found in American Airgun Field Target Assosciation using 1.5”, 1”, ¾", ½", and 3/8”.
WFTF style- represents common kill zones found in World Field Target Federation using 15mm, 25mm, and 38mm apertures
10-15- Inspired by customer request, uses 10mm and 15mm apertures. High-Precision shooting.
The Sig Sauer MCX Virtus PCP .22 Caliber Pellet Rifle is one that you are really going to want to take outside and set targets up around 50-60 feet await make it a little more challenging adn I do plan on getting outside with the Sig Sauer MCX Virtus PCP .22 Caliber Pellet Rifle in a bit once the weather gets a bit nicer and have some fun shooting at longer ranges. For now I wanted to at least get out my Indoor Field Test Shooting Video where I can Chronograph the Sig Sauer MCX Virtus PCP .22 Caliber Pellet Rifle and also see what it can do shooting at 30 feet out.
Sig claims the Sig Sauer MCX Virtus PCP .22 Caliber Pellet Rifle to shoot .22 caliber lead pellets at up to 700 fps with a power output of 12 foot pounds. Using 14.5 grain lead pellets I placed 6 rounds though my Chronograph and averaged 585 fps with the fastest shoot hitting 611 fps. Keep in mind there are much lighter lead pellets out there and when it comes to alloy pellets they drop in weight even more so hitting 700 fps with a light grain lead or alloy pellet is very realistic. What about Sigs claimed 12 foot pounds of energy? I did the math and using a 14.5 grain pellet with a maximum velocity of 611 fps, these numbers produce just a hair over 12 foot pounds! Mission accomplished :)
What about accuracy, I have seen a few claims online that the Sig Sauer MCX Virtus PCP .22 Caliber Pellet Rifle is not the most accurate Pellet rifle out there and you know what I don’t think that was the absolute intension when Sig thought this one up. After all it is a semi auto high capacity Airgun replica, not a target rifle. I still like to find things out for myself so of course I performed my accuracy test for the Sig Sauer MCX Virtus PCP .22 Caliber Pellet Rifle shooting 10 rounds into a fresh paper target from 30 feet back using a seated and rested shooting position. For this test I was using a red dot scope with a 3x magnifier on it. My first 10 rounds did OK producing just over a 1 inch grouping, not super great but most of the rods (8 of them) all struck the target within about 3/4 of an inch.
At this point decided to empty the rest of the magazine so about 15 rounds on the same target to see if the grouping stayed the same or maybe even speed out a bit. I was a bit surprised to find that my second 15 shot grouping all stayed within the higher 10 shot group again producing about a 3/4 inch grouping with just those two first test outliers? Maybe it was me, maybe it was the pellets, maybe it was the Sig Sauer MCX Virtus PCP .22 Caliber Pellet Rifle? The good news is you have 30 rounds to hit your target so even if a couple of them stray a bit you still got 28 left to get the job done.
The Sig Sauer MCX Virtus PCP .22 Caliber Pellet Rifle is one of the coolest Air Rifles I have tested and now own, not only is it a great Replica Airgun but it also performs well and can be used for plinking or small pest control. All at even a fraction of the cost of shooting 22LR rounds and that’s not even that expensive compared to 9mm and larger ammo. Let’s hope Sig Sauer makes a detuned Canada version so we can offer it up in our Canada Replica Airguns Store and if you live in the US then checkout the US Store for Sig Sauer buying options.
