Trigger Pull: The trigger pull on the B&W Dragunova SVD Airsoft Sniper Rifle is good overall, just a bit of initial take-up and then a medium trigger pull to release the heavy spring. You will of course nee to pull the charging handle with each shot to preload the spring.
Accuracy: My initial accuracy testing was done from about 45-50 out using .36 gram Airsoft BB's, it was a fairly windy day but even so I was able to get a nice tight 2 inch grouping using a semi rested position. I also put the Dragunova SVD through my Chronograph testing and shot both the lighter .20 gram and heavier .36 gram BB's to see what kind of fps I would get using both weights. The lighter .20 gram BB's got right around 500 fps while the heavier .36 gram BB's shot a bit lower at approximately 380 fps. I did however find that sighting the SVD in for windage adjustments (left and right) was a bit of a challenge as you can only adjust the front sight by loosening it with an allen key and make only very slight left to right adjustments. I was not able to get the SVD to shoot far enough to the right using this method so I amy need to do figure something else out, perhaps a scope setup?
Build Quality: The B&W Dragunova SVD Airsoft Sniper Rifle is not a super expensive rifle but still has a good combination of metal and plastic components. Most of the parts that you would find on the real SVD are metal including the barrel, bolt/charging handle & receiver, trigger, magazine, sights, strap rings and rial system. The stock is of course plastic with some added rubber. The B&W Dragunova SVD is not overly heavy but still has a reasonable amount of weight to make it believable. Performance was very good with no mechanical problems other than the last two BB's in each magazine do not load into the rifle.
Realism: I have never held an actual Dragunova SVD in my hands but from what I have seen in photos, it looks to be a good copy of the real steel Russian sniper rifle. Lots of metal helps pull of the realism, a working charging handle, removable bolt cover, and lots of other working components make for a believable looking and functioning version of this Airsoft BB shooting Dragunova SVD Sniper Rifle.
Lots of metal parts throughout where they would be on the real SVD.
Good power and accuracy combination.
Fairly high capacity magazine at 40 rounds.
Sights are adjustable for elevation front and back and a bit for windage.
Bolt is surprisingly easy enough to cock with either left or right hand.
Lots of upgrades available for this sniper rifle.
Inexpensive way to own a piece of history.
Cons:
Some discrepancies in the manual (180 fps and 100 round magazine)
Sighting for windage may not be adequate?
Would definitely be much nicer with the wood stocks.
Two BB's always pop out of the magazine area when empty.
Comments:
I found the B&W Dragunova SVD Airsoft Sniper Rifle to be a lot of fun to shoot, I was not sure how the charging handle system was going to work in terms of weight and easy of use to pull it back. I ended up using my left hand and reaching across and over and surprisingly this was very efficient and effective in charging the spring and allowed me to keep my righthand in place and on the trigger for very quick follow up shots. Power was as much as you would want from a sniper rifle and accuracy was also very good even in windy conditions. The only real problems I had where the two BB's that did not load from each magazine and the windage adjustments not quite allowing me to move my aim point enough for a bullseye at 50 feet out. I would recommend this B&W Dragunova SVD Airsoft Sniper Rifle and would suggest possibly adding some wood stocks and a magnified scope setup.
Testing out the ASG - Marushin CZ 75 Blowback Shell Ejecting Airsoft Pistol was not an easy one but I did manage to get thorough it! First there was the setup, I could not shoot the ASG Shell Ejecting CZ 75 Airsoft pistol on my deck or I would have fore sure lost most of my shell casings for it. So I decided to setup camp in my pool area where I have a nice large flat area off to one side, I put down a ginormous tarp in hopes to catch the radically flying shells but even this failsafe did not catch them all as I later found out ;)
As with most of my Field Test Shooting videos, I usually do a bit of a pre test to make sure the gun is functioning properly and so I shot a full magazine of my brass shells through the ASG CZ 75 and it worked like a charm, of course when I started recording the live video it decided not to work at all and I still do not know why? I was able to revert back to the plastic shell casing that came with my ASG CZ 75 Blowback Shell Ejecting Airsoft Pistol and they seemed to be working so I went with them for my testing. Interestingly enough the brass shells got much higher fps (around 300+) when I did my pretest compared to around the 250 average fps I was getting with the plastic shell casings.
Shooting on target proved to be better than I though once I raised my sight point up a bit, the gun likes to shoot a bit low but once I found the sweet spot I got three rounds within about 3/4 of an inch from just over 20 feet away in a semi rested position.
I would not recommend this Airsoft gun as an everyday shooter and there is no way you could use it in any type of Airsoft simulation as the ejected shell casings would get lost for sure and the cost to shoot the ASG CZ 75 would get very high indeed! It would be good for use in a movie or video where you wanted the realistic look of shells being ejected and did not want to use a blank gun or render the shells in post. And of course it is just really cool to have an Airsoft gun that has ejecting shells :)
Materials: Plastic slide & frame, some metal parts.
Weight: 1.4 pounds (616 grams).
Barrel: Metalnon-rifled smooth bore.
Propulsion: Propane, green gas.
Action: Blowback, single action only.
Ammunition Type: 6mm plastic Airsoft BB's.
Ammunition Capacity: 8 rounds.
FPS: 279+ fps.
Trigger Pull: The trigger pull on the ASG CZ 75 Shell Ejecting Airsoft Replica is single action only, unlike the real steel version that actually has a single and double action trigger. The single action trigger has a light to medium pull but does have a fair bit of take-up to it.
Accuracy: I did not pre-test the ASG CZ 75 as the shells fly everywhere and you really need to be able to retrieve them afterwards as the cost to replace the shell casing is rather high. I do plan to do a full Shooting Field Test where I will shoot the ASG Shell Ejecting CZ 75 through the chronograph, place some shots on a target and also capture the action of this pistol in slow motion with a high speed camera. So stay posted for that. I can say that from the few shots taken in my house, that it seems to shoot pretty hard and the shells really com flying out of this gun with force, I also noticed that a BB does have to be loaded into each shell for there to be enough back pressure to allow for a full slide blowback and ejection of each shell.
Build Quality: Even though this gun is made mostly out of plastic and from what I can tell is also made in Taiwan, it has a very good overall fit and finish. The slide slop is next to none and the licensing and markings look great. There are metal parts where they really need to be like in the barrel, hammer, trigger, safety, slide catch, magazine and a few other internal parts.
Realism: The ASG Shell Ejecting CZ 75 Airsoft Pistol is one of the most ultra realistic Airsoft pistols I have seen and mimics a real steel gun right down to the shells being ejected, how cool is that! If it had more metal then that would really top it off. Even with the plastic slide and frame it is very realistic in almost every way and even field strips just like a real CZ 75 and is fully licensed. The only feature not true to the actual CZ 75 would be the single action only trigger.
Excellent fit and finish - tolerances are very good.
Very believable working replica of the real steel CZ 75.
Fully licensed.
Fully field strip-able.
Nice heavy full size drop out metal magazine helps give it some needed weight.
Has metal parts where they need to be.
Cons:
Plastic slide and frame.
A bit low in the FPS department.
Only 8 rounds in the magazine.
Can not really use in the field, would lose too many shells.
Comments:
The ASG CZ 75 Shell Ejecting Blowback Airsoft Pistol is a very unique Airsoft gun, not very many Airsoft guns actually have ejecting shells. Just because of that I had to have it! Overall it is a pretty decent gun but I have yet to really test it out and that is the biggest shortcoming with this gun, you can't just shoot it anywhere as you need to shoot it in a place where you can recover your spent shell casings, unless of course you have all the money and shell cases in the world... That said it has a lot going for it other than the ejecting shells; Fully licensed and trademarked, blowback operation, full size drop out metal magazine and it's fully field strippable. I am sorry to say we don't offer it in out Canada or USReplica Airguns Store but we do have a similar all metal CZ 75 Airsoft offering in the form of the KJWorks KP-09 which I have done both a Table Top and Shooting Review for.
I do get requests from many of my viewers to do some real steel reviews and so far I have pretty much stuck with 22LR real steel reviews and my Tokarev real steel review. I recently purchased an interesting 10mm semi auto handgun used at a local used gun show and so I though I would share this rather interesting and no longer in production pistol with you. The handgun we are looking at today is the Wyoming Arms Parker 10mm S.S. At first place it looks a lot like a 1911 but it is different in several ways. the obvious traits are the safety on the slide and lack of a grip safety, it also has a very different looking handle and there are some internal differences also.
What drew me to the Wyoming Arms Parker 10mm S.S. was it's 1911 looks, the very nice stainless steel finish and the rather unusual 10mm ammo it was chambered to shoot. If your not familiar with the 10mm round it was developed by the FBI for sue by their field agents but was later determined to be a bit too much to handle for some of their smaller but later agents. The 10mm was then detuned and turned into the S&W 40 caliber which is essentially a shorter less powerful version of the 10mm.
Here are a bunch more photos that really show off the beauty of this pistol!
Definitely make sure to watch this video as I go through the gun and show you around, I also do a field strip and talk a bit more about the Miami Shootout that was the FBI's reason to look into the development of the 10mm Auto round.
Materials: Metal and plastic (polymer) construction.
Weight: 1 pound 10.5 ounces (752 grams).
Barrel: 3.3 inches, metal rifled.
Propulsion: CO2 x 1.
Action: Semi auto, single and double action.
Ammunition Type: .177 caliber pellets
Ammunition Capacity: 8 shot rotary magazine.
FPS: 360.
Trigger Pull: The trigger pull on the Umarex Walther CP99 is in the mid range for it's double action trigger pull with most of the effort at the beginning and middle stages as it cocks the hammer and indexes the rotary magazine, it does have a predictable release point making it easy to put pellets on target. By racking the rear slide you can put the CP99 in single action mode which makes the trigger pull much lighter and great for very accurate shots.
Accuracy: I shot this air pistol at a target from 20 feet away in a free semi rested position and it performed well getting a nice tight one inch eight shot grouping just to the left on the target. The sights can be adjusted for windage if your aim is off to one side or the other. With my preliminary Chrony Chronograph testing using 6.9 grain RWS lead pellets I got pretty close to the factory claim of 360fps with an average of right around 346 fps.
Build Quality: The Umarex Walther CP99 is a metal and polymer air gun with a good deal of metal components on the inside giving the Walther CPSport a decent overall weight and heft. It's worth mentioning that the Walther CP99 has a full size drop out magazine for holding the CO2 cartridge that gives the air gun some additional weight and functionality. The German made fit and finish is very good on the CP99 and the plastic quality is also very good.
Realism: The Umarex Walther CP99 is licensed by Walther and is based around the Walther P99. The frame is very similar to the P99 but the slide is not as accurate in terms of the real steel but you can definitely tell the Pellet shooting CP99 is a copy of a Walther P99. One of the biggest shortcomings is the safety, the real P99 does not have a safety but Umarex decided to put a rather large safety on the right hand slide area. I do however like the working de-cocker, slide catch for loading magazines and full size drop out magazine which give the Umarex CP99 a more realistic look and feel.
Slide catch and de-cocker are realistic and functional.
Rifled barrel.
Sights are adjustable for windage.
Slide catch and magazine release are fully functional.
Nice full size drop out CO2 magazine.
Good combination of power, accuracy and CO2 efficiency (I got about 100 shots from a CO2)!
Rail for accessories.
Walther licensing.
German Quality.
Cons:
Up in the higher price range.
Double action can have some stickier shots.
Kind of funny safety, not true to the real steel Walther P99.
No recessed barrel
Comments:
The Umarex Walther CP99 Pellet CO2 Air Pistol is a nice step up from the Walther CPSport I reviewed earlier. The CP99 is a much more accurate looking replica of the P99 and it also has more metal parts and a single and double action trigger. These added features do come with an additional $100 price tag but in my opinion are worth it. If you're a fan of the Walther line of pistols than you should probably take a look at the Umarex Walther CP99 as it would make a great addition to your airgun collection.
Ammunition Capacity: 13 round full size metal magazine -18 round metal stick magazine.
FPS: 428 - 380.
Trigger Pull: There is a lot of difference between the trigger on both of these guns, first off the Umarex Makarov has both a single and double action trigger/hammer while the KWC Makarov has a double action only trigger/hammer. Comparing the double action of both guns the definite advantage goes to the 4.5mm Steel BB shooting Umarex Makarov as it is shorter and lighter, the KWC Airsoft Makarov does not have a bad trigger but it is much longer and a bit heavier, but still very usable. The single action trigger on the Umarex Makarov is not really any lighter than when shooting in double action, it is however much shorter with a medium take-up and predictable release.
Accuracy: Both Airsoft and BB Makarov's performed very well in their shooting tests for me, they bot shot fairly well centered with the KWC Makarov getting all five shots in the black bullseye and the Umarex Makarov having a tighter group but just off to one side. This was good news since both guns do not have adjustable sights! They also scored very well in the velocity department shooting over their advertised claimed feet per second rating. The Umarex BB version shot a very respectable 390 fps while the KWC Airsoft pistol shot a very surprising 480 fps well over the claimed factory 430 fps. Both guns also shot very accurately out to ranges of 50 feet or so. From a single CO2 I was able to get 162 shots from the Umarex Makarov and 112 shots from the KWC Makarov before I noticed a significant power drop.
Build Quality: Neither one these Makarov replicas is going to win a prize for build quality, some shortcuts have been made to keep the price down on each model, but they are both built with mostly metal parts and they both performed perfectly for me during my testing. The Umarex 4.5mm Steel BB Makarov did have more moving parts while the KWC did weigh in a bit heavier, both guns had reasonable fit and finish to them.
Realism: In terms of being good Makarov replicas the pair for sure look the part, size and overall weight are very true to the original real Steel Makarov PM with the Umarex Makarov having a working slide, Makarov licensing and the ability to be field stripped. The KWC Makarov had a nicer recessed barrel and full size drop out metal magazine. I was not a big fan of the KWC screws on the right side slide or the Umarex exposed CO2 tab.
KWC may shoot a bit too hot for CQB Airsoft games.
Both guns do not have adjustable sights.
Comments:
To be honest when I got the KWC Airsoft BB shooting Makarov, I was not all that awe struck, the lack of a working slide, DOA trigger and screw holes in the slide put me off just a bit. This Airsoft pistol did warm up to me a lot once I shot it, I was surprised by the very high fps and how accurate it was for such a low cost Airsoft pistol. I can really see this gun being used as a backup or sidearm in an out doors style Airsoft game where you may need to shoot targets out at range where other lower powered pistols just would not be able to get out to. The Umarex Makarov has always had a place in my heart, it is just a really good little CO2 BB pistol for the price with mostly all metal parts, a working slide, single and double action trigger and very good overall performance. In my books you can not go wrong choosing either of these Makarov replicas so choose wisely!
My Vimeo Video Table Top Comparison Review for these Makarov Air Replicas:
This is not meant to be a full review of either the BB or Airsoft version of the Cybergun - KWC CO2 Blowback Mini UZI's but I do talk about specifications, show you around both guns, and put them both through a full Field Test so I guess in a way, perhaps it can be considered to be a full review ;)
I will list the specifications here for you but I am not going to get into details like Trigger Pull, Build Quality, Accuracy and Realism. You can check out my other video reviews for more information on the Mini UZI:
As I said you can check out all my other videos for info on these very accurate Mini UZI Replicas, I mainly want to go over some of the main differences and similarities for both the BB and Airsoft versions.
In terms of build quality they are made almost exactly the same and weigh in at a hefty near 5 pounds, the only differences are the inner barrel and magazines to accommodate the different sized ammo. The BB version has a 25 round single stack magazine that does not have a follower to stop the bolt from continuing to operate even after the magazine is empty. While the 6mm Airsoft version has a double stack magazine that holds 38 rounds and does have a follower to stop the bolt which can save you some unintentional wasted CO2.
The Airsoft Mini UZI version is distributed by KWC while the 4.5mm BB version is distributed by Cybergun, you will find the UZI and IWI licensing on the Cybergun 4.5mm BB version but not on the KWC 6mm Airsoft version.
Out of the box the KWC Airsoft Mini UZI is ready to go in both semi auto and full auto while the 4.5mm steel BB version will only shoot in semi auto mode, it can however be easily modded to shoot in full auto.
Both guns come in cardboard boxes with manuals, some BB's and an Allen key to tighten the CO2. The KWC Airsoft Mini UZI also comes with a handy speed loader.
There is a slight fps velocity difference between the two with the KWC Airsoft 6mm plastic rounds traveling at around 400 fps (with .20 gram BB's) and the 4.5mm Steel BB's traveling at right around 350 fps. In the field test portion I test both guns out on some water filled cans to see how each ammo type performs in terms of penetration.
Your best bet is to watch both my Table Top and Field Test Comparison Video Reviews and see for yourself how they compare!
Earlier this week my father called me up and asked if I wanted to head out with him to go do some hunting/shooting. He has his bear tag but for the most part, hunting with my Dad consists of driving around in his truck hoping to stumble on something since he can not walk all that far these days.
We had a great time just enjoying each others conversation and of course the beauty of Canada BC's Harrison Lake area. We also got to shoot some guns to "make sure they where sighted in and working correctly". I brought my Norinco 12 Gauge Homeland Security 780 which I needed to test out and I'm glad I did since it needs some TLC to get working smoothly. I also brought along my little Henry Lever Action 22LR which is always a blast to shoot. My Dad brought his Savage Arms 7mm Magnum just in case we did see a bear on this outing.
Long story short we didn't bring any meat back home with us but we did see some out of season doe and of course had some nice father-son time together...
One question that comes up often is the danger attached to blank gun use and the most common question I get is about the danger of shooting a blank gun at a person. Blank guns have many uses, one of which is to be used as a prop in a movie or reenactment. In this situation one may want to point and shoot a blank gun at a person to make teh scene more believable it. If the person is far enough away there is usually no cause for concern but with that said I would personally point the gun just off to one side in the event that something might come loose within the gun barrel or perhaps a fragment of something where to be fired and cause an injury to the person the gun is directed towards. With creative camera angles you shouldn't need to actually point a blank gun directly at anyone.
People also assume that because a blank gun does not actually fire a bullet that it is relatively harmless. This is not true at all, in the larger caliber blanks there is about the same amount of energy to what your would find in a real bullet, this is so the blank gun will sound about as loud as a real bullet being fired. The difference with how the energy is released in a blank round versus a real bullet is that the bullet caries most of the energy with it and when the bullet hits its intended target, the bulk of the energy is transferred to that target.
The energy from a blank round dissipates almost immediately after it leaves the gun barrel but the energy right at the barrel tip is very similar to that of a real bullet, especially if it has nowhere to go but directly into an object. So yes a blank gun round can be lethal at very close ranges and unfortunately several people have paid with their lives finding this out for themselves.
With this newfound information about blank gun danger, some people might say... get rid of these dangers to society! Before we head in that direction think about how many other non vital things we have in our lives that I would have to say have claimed way more lives than blank guns could even come close to: Off-road pleasure vehicles, Skydiving, Skying, Pools, Real Guns to name a few! Blank guns also serve very useful purposes like being used to signal a warning or distress, send out flares, ward off wild animals, train people on how to use a real gun, and of course dog training. I am sure the good outweighs the bad here.
That's enough politics for now, juts watch the video and see for yourself why you should not point a blank gun at anyone, especially if the person is very close in proximity to you!
Trigger Pull: The trigger pull on the RG-300 and RG 3 is double action only and a bit on the heavy side so you will need to hold the gun firm and apply an even and long pull to fire the these blank guns, after a few shots you get the hang of it. If you do not pull the trigger the entire way back until the hammer releases, the shot will not fire but the blank will index and move onto the next round so you may have an unused blank when you pull out the magazine.
Accuracy: NA.
Build Quality: The overall build quality for the ROHM RG-300 and RG 3 blank pistols is very good, being German made they are built to last and the fit and finish is very good. The only real plastic would be the grips on both models which is to be expected. Both guns worked perfectly for me during my testing and with the exception of a bit of a heavy DOA trigger pull since the trigger first has to index the magazine and then fire the round.
Realism: The ROHM RG-300 and ROHM RG 3 are not exact replicas of any given guns in production as this would make importing them into Canada even more difficult. The ROHM RG-300 does however share some similarities in looks to that of a Sig Sauer but in a much smaller form factor !
German made quality, materials fit and finish is all excellent.
Almost all metal with some reenforced steel parts.
Very safe double action triggers, will not accidentally misfire on you.
Both are front firing.
Come with flare adaptors and cleaning rods.
Available for import into Canada.
Cons:
Not actual exact replicas of any specific guns in production.
Double action trigger pull is a bit tough and takes some getting used to.
Expensive due to them being harder to get and in high demand in Canada.
Comments:
One nice point with the .22 caliber blank shooters is the lower cost to shoot them, .22 caliber crimped blanks work out to be much cheaper than the 8mm & 9mm P.A.K. or .380 crimped blanks. Sure they are a bit quieter but louder than you might think, especially when coming out of a short barrel. Another selling point is how compact both of these guns really are which makes them easy to pack around if you want to take one with you on a hike or outing as a deterrent for any wildlife that may get a bit too close to you. The RG-300 and RG 3 are two very nice additions to the ROHM blank guns we sell in the Canada Replica Airguns Store.
I don't often get to shoot my airguns out at the 100 foot mark but I purchased my Sheridan Silver Streak .20 Caliber Multi Pump Pellet Rifle mainly to shoot up to and even past this fairly distant range as the Silver Streak is my new vermin gun for pests around the farm. I get a lot of Crows that to be honest are just feathered bullies that pick on all the other friendly birds on the farm, they have also been known to get into my garbage and even attack the Eagles and Hawks in the area. Flying Rats I like to call them.
In this Field test Shooting video I test out my brand new Sheridan Silver Streak on the Chronograph to see just how powerful it really is not just at the maximum 8 pumps but also at 3 and 5 pumps. I was actually very surprised at the very decent power I got from only 3 pumps (460 fps), you could easily take out a small rat with the 14.3 grain .20 caliber lead pellets I was using for my Chrony test. At 5 pumps I gained close to another 100 fps and at 8 pumps I maxed out at just a hair under 640 fps respectively. With the 14.3 grain pellets I was using this worked out to right around 13 foot pounds of energy. (My Sheridan was purchased using a PAL)
I also shot my Sheridan Silver Streak .20 Caliber Pellet Rifle at a target setup 100 feet or just over 30 yards away and was able to get what I felt was a nice 1.5 inch 5 shot grouping. 4 of the 5 pellets where all within 1 inch of each other with my first shot being a bit lower and to the right of the rest spreading the group out to about 1.5 inches. Keep in mind I was also a bit winded from all the pumping and I could feel and see my heartbeat in my 9 power Bushnell scope making my crosshairs bob back and forth ever so slightly.
I have not shot my Sheridan Silver Streak all that much and plan to hone my skills further so when the time comes I will be ready for them pesky crows.
Stay tuned for my future Table Top review of my Sheridan Silver Streak, for now you can checkout my Preview video that has some preliminary info.
For the most part, this video is to test out some cameras and using them all together in a multi-camera scenario. I wanted to see how many camera angles I could shoot at one time and see how they would all work together when editing the video.
Cameras used:
My new Pivothead Recon Camera Glasses.
Sony HDR-AS15 Action Cam.
Drift HD170 Point of View Camera.
Nikon 1 with 10mm fixed lens.
Casio TRYX.
*All cameras where shooting in 1080p for this video.
I hope to use camera setups like this in the future, maybe not all at once but at least a couple at a time to give you some viewing options.
I picked out my WE SCAR GBB Airsoft Rifle for this test as it had a lot of mounting points and the Gas Blow Back makes for some great video action. Unfortunately My WE SCAR was not working at 100% but I still think I was able to pull off this test video either way.
Watch my Multi-Camera-Angle Test Video shooting the WE SCAR GBB AIrsoft Rifle:
Here is my official Field Test Shooting Video Review for my Daisy Winchester Model 11 CO2 Blowback BB Pistol. Make sure to checkout my previous Table Top Review for more details on the Winchester Model 11 1911 CO2 4.5mm BB version where I also did a pre-test showing similar results.
My 5 shot Chronograph test resulted in a bit lower than previously tested 339 average fps while my accuracy test shot from 20 feet out in a semi rested position got six shots right in the 1.5 inch bullseye with 4 shots coming out a bit, 2 of which spread the group out to about a 3 inch grouping in total. So in terms of shot placement you could say the Daisy Winchester 1911 4.5mm BB Pistol shot very well centered. Agin this time around I got 6 full magazines but had to manually clock teh hammer back on some of the last magazines end shots, power did seem OK even when manually cocking the hammer.
Overall, the Daisy Model 11 4.5mm BB Pistol is nice pretty much all metal low-cost CO2 Blowback BB pistol with good overall performance. This one looks the part of a 1911 even though it may not function 100%. If your OK with close and want to save a few bucks, then teh Daisy Winchester Model 11 may be for you, if you don't mind spending a bit more to get a BB gun as close to a real 1911 A1 as possible than take a look at the KWC/Cybergun Tanfoglio Model 1911 full blowback BB Pistol and Airsoft Pistol versions.
Here is my official Field Test Shooting Video Review for my KWC Sigma SW40F CO2 Blowback BB Pistol. Make sure to checkout my previous Table Top Review for more details on the KWC SW40F 4.5mm BB version where I also did a pre-test showing some similar results.
My 5 shot Chronograph test resulted in a somewhat expected 285 average fps while my accuracy test shot from 20 feet out in a semi rested position received a slightly wider 3 inch group this time but with most shots being within 1 inch of each other. In terms of shot placement the KWC SW40F 4.5mm BB Pistol shot very well centered but just slightly low. I also only got 2 full magazines this time around so don't expect a lot of shots per CO2 with this 4.5mm BB pistol.
Overall, the KWC SW40F 4.5mm BB Pistol is a really fun gun to shoot with a very crisp heavy slide that gives a nice firm blowback snap to it. It is one of the nicer sounding slides with a less tinny sound than most. The fps and shots per CO2 is a bit low but other than that performance is very good, you will have no problem nocking down cans and acquiring other miscellaneous targets.
ALL GUNS ARE NOW SOLD - THANKS FOR THE AWESOME RESPONSE!
This is a first for me but I guess you could say I have to make room for some more guns ;) I have some duplicate guns and a couple I juts don't have a need for anymore so instead of having them sit around collecting dust, I thought I would offer them up for sale and get them in the hands of someone who can really appreciate and get some use out of them...
Here is a list of the items up for sale:
Baikal IZH-61 .177 Caliber Spring Piston Pellet Rifle: $115
Baikal MP-655K Pellet/BB CO2 Pistol (missing pellet magazine): $125
Umarex CP99 Compact CO2 BB Blowback Pistol: $50
Swiss Arms Sig Sauer GSR 1911 CO2 BB Pistol: $30
ASG CZ 75 P-07 DUTY Dual Tone CO2 BB Blowback Pistol: $125
Umarex Beretta M92FS .177 Caliber CO2 Pellet Pistol - Nickel with Wood Grips: $200
(2x) AK47 BB Gun Magazines: $50 Each
Crosman 2240 .22 Caliber CO2 Pellet Pistol (14 inch barrel, RJMachine Breach/Brass Bolt, Wood Grip, NcSTAR 6x32 Scope): $225
Shipping/Handling is $15 Canadian and $25 to the US and you must be 18 or over to buy. You will need to email me at mike@replicaairguns.com to let me know what gun/guns you want to buy - first come first serve, I will send a PayPal request to the person with the first offer to buy and give them 24 hours to pay or I move on to the next buyer.
You can watch my YouTube Video to get a good look at each pre-owned item up for sale:
I like to show off some of my acquisitions from time to time even if they are guns I don't necessarily have for sale, I am a collector and some items are not always common enough or even popular enough to keep in our Replica Airguns Store.
Today I show you two blank guns I picked up from a recent gun show I attended in Chilliwack BC. There where not many blank guns at the show, the two I found may have been the only blank guns there, at least that I saw? The ROHM RG300 .22 Caliber Blank Pistol and RST MOD. 1966 .22 Caliber Blank Revolver I picked up for a pretty good price, at least in my mind, $55 for the ROHM and $20 for the RTS. A nice addition to my blank gun collection!
I have been contemplating between a PCP (Pre Charged Pneumatic) or a really good Multi-pump air rifle for pest control around my house, I have been using a spring piston rifle but the combination of my limited skills with spring piston rifles and the fact that most pests in my area stay a good 50+ yards back, means I need an airgun with pin-point accuracy. At the end of the day I decided on the Sheridan Silver Streak because it was a bit more affordable than a PCP air rifle and also the Sheridan is such a classic air rifle but still with the right amount of power and accuracy to get the job done.
Trigger Pull: The trigger pull on the Daisy Winchester Model 11 is very nice, just about the perfect pull weight, not too heavy or too light, it has next to no take-up at all and a nice predictable release point. As is traditional with a 1911 styled pistol, the trigger is single action only so you will need to either pull the hammer back or rack the slide for the first shot, with subsequent shots you will not have to do this as the blowback action cocks the hammer for single action shooting. If your CO2 is very low, the blowback may not be adequate enough to cock the hammer so you can do this manually to get a few extra shots out of the Daisy Model 11.
Accuracy: When I shot the Winchester Model 11 from 20 feet out in a semi rested position, I was able to get some decent results. I placed 10 rounds within about a 2 group and the shot placement was very well centered, just a slight bit to the left. I did get a couple of stragglers that spread the group out just a bit larger but not too much. I did also get right around 350-360 fps on my chronograph on this not so warm day. We will have to see what my dedicated field test results yield for this BB pistol.
Build Quality: The Daisy Model 11 (1911) is made in Japan and has a nice overall finish to it. Other than the plastic magazine and grips it is an all metal gun so the materials used are good. The slide does have a bit of wiggle play in it but so do many blowback air pistols, perhaps to reduce some friction as the slide springs on these guns are not overly heavy. The paint used seems to be holding up very well and looks good, I did notice a molding seem that runs down the underside of the slide and along the trigger guard.
Realism: The Daisy Winchester Model 11 is a replica of the real steel 1911 A1 style 45 auto. It does have the Winchester licensing on it but I am not sure if there is an exact Winchester 1911 this gun is made to replicate. For the most part it looks and functions very similar to a real 1911 with a few exceptions like the lack of a working grip safety, a rather strange two stage safety and also the stick styled smaller magazine. This blowback air pistol can not be field striped conventionally either. I do like the true single action trigger and open ejection port.
Lots of metal in this airgun and good weight to it.
Good overall looking replica of a real 1911.
Reasonably decent blowback feel.
Mid range fps and shots per CO2.
Very nice true single action trigger.
Shots where well centered and got decent accuracy.
Markings and instructions on gun are color matched.
Solid CO2 tightening system, seems to work well once you get the hang of it.
Not bad at all for the lower price point.
Like the open ejection port.
Made in Japan.
Cons:
Kind of funny safety setup, it is redundant?
Has a plastic magazine, would have been nice in metal.
Back strap safety does not actually work but it does move.
Says "clip" instead of "magazine" on gun.
Comments:
I know some people have been hating on this gun for a couple of reason so let's get them out of the way... Yes it has a weird safety setup and I can not tell you why Daisy did this, perhaps they wanted it to be "more safe"? As a 1911 trainer you will have to adapt how you take this gun off of safety over a traditional 1911 setup. The magazine is plastic, not a biggie, if it breaks on you get another one. It's not full blowback like the Cybergun/KWC Tanfoglio 1911, this is true but you do get higher fps and more shots per CO2 out of it because of this. And yes Daisy uses the word "Clip"on the gun instead of the correct term "Magazine". Honestly, the Daisy WInchester Model 11 is a nice overall BB gun and the price point is pretty low for what you get. It looks really good overall and shoots nicely with enough blowback to give you some recoil feel and allow for true single action shooting. You also get decent fps and a good amount of shots from a single CO2 cartridge so stop complaining and just enjoy this gun for what it is!
My Vimeo Table Top Review of the Daisy Winchester Model 11 Blowback CO2 BB Pistol:
Trigger Pull: The trigger pull on the KWC Sigma SW40F CO2 Blowback BB Pistol is single action only which generally produces a very light trigger, on the SW40F it is a bit firmer than most single actions but still decent with a short take-up and firm release. You will need to pull the slide back (which also chambers your first round) to cock the internal hammer, after which subsequent shots you will not have to pull the slide back as the blowback action does this for you.
Accuracy: When I shot the KWC Sigma SW40F from 20 feet out in semi rested position I was able to get nice clean results. I placed 10 rounds within about 2 inches with the shot placement being very well centered. The KWC S&W Sigma SW40F seemed to keep the rounds tighter from top to bottom over side to side for me. I also noticed when I field stripped this gun that there is a built in hop-up (rubber bar) that sits inside the barrel, this will produce some back spin which will keep the BB's trajectory a bit flatter when shooting further out and is also probably there to stop BB's from rolling out of the barrel once chambered.
Build Quality: The build quality is about the same as all other KWC guns, tolerances seem tight and everything is working as it should, you will get some wear marks (paint wear) on the high spots over time which is normal on just about any (type of gun, real or air) but what I like about the SW40F is that the barrel is polished and since this is the first area to lose paint, it really does not matter since no paint is on the barrel.
Realism: The KWC Sigma SW40F CO2 Blowback BB Pistol is a replica of the real steel S&W Sigma with the exception of the licensing and it really is a bang on Replica, you can field strip this gun exactly like a real Smith & Wesson Sigma. All the mechanical parts work just the same and I like the fact that without the licensing, this gun is very clean looking with no obtrusive warning instructions on it.
Lots of metal in this gun with very good weight to it.
Very accurate S&W Sigma replica.
Heavy crisp blowback feel.
Predictable single action trigger.
Shots where well centered, got good accuracy.
White dot sights for quick target acquisition.
No ugly warning markings.
Full size drop out magazine holds BB's and CO2.
Like the polished barrel and ejection port.
Fully field strip-able.
Cons:
I only got two magazines in my pre-test for some reason?
FPS is not super high?
A bit finicky when loading BB's
Comments:
Just like my Airsoft review of the KWC Sigma SW40F, this blowback Air Pistol was a lot of fun to shoot, with it's super snappy heavy slide and ultra realistic shooting characteristics. It did seem to go through a lot of CO2 very quickly which is not uncommon for this style of full blowback heavy slided airgun, and to be honest I don't really mind since it shot well, felt good in the hand and backs it up with great looks. And heck it's still so much cheaper to shoot than a real 9mm hand gun ;) For those of you looking for something that is similar to a Glock in terms of looks and operation, the KWC Sigma BB or Airsoft pistol may be your only real option here in North America now that the Umarex SA177 is history.
My Vimeo Table Top Review of the KWC Sigma SW40F Blowback CO2 BB Pistol:
Trigger Pull: The trigger pull on the Cybergun Sig Sauer P226 Airsoft Replica is good in both single and double action. Once the slide is pulled back and released the first round is chambered and the hammer will remain back placing the P226 in single action mode, the pull is light and the take-up is fairly short, most of your shots will be in single action mode unless you use the de-cocker to lower the hammer for a subsequent double action next shot, double action shots are still pretty light but much longer in order to cock the hammer.
Accuracy: Shooting the Cybergun Sig P226 from 20 feet out in semi rested position I was able to get very good results. I placed 10 rounds in about 1.5 inches with the shot placement being a bit low possibly due to my barrel mod, adjusting the hop-up may bring the aim point back up to where it should be. The Sig Sauer P226 Airsoft Replica shot right around the 316 fps range while conducting my 5 shot average chrony testing which was lower than advertised but I was using much heavier .20 gram BB's. You can expect to get a full magazine worth of shots out of each gas fill-up but I did notice that as the magazine got colder it did tend to become much less efficient and also seemed to vent a lot of vapor.
Build Quality: The build quality is generally good and I was surprised at the finish on this model as the paint is not showing any wear marks so far, the fit is good with minimal slide and barrel wobble and everything is working very well with no problems so far with a fair amount of shots through it, guess you could say I like shooting this gun :) Most of the gun is metal with only the grips and a couple internal parts being plastic.
Realism: The Cybergun Sig Sauer P226 6mm Airsoft pistol is a replica of the real steel Sig Sauer P226 right down to the licensing and it really is a great looking and functioning Airsoft Replica. You can field strip this gun exactly like a real Sig and all the mechanical parts work just the same including a working de-cocker and adjustable front sight.
Seemed to shoot a bit low for me, could adjust with hop-up a bit?
Only one magazine per Gas fill.
Comments:
I am a big Sig Sauer fan so it would take a lot for me to not give this gun a good review, with that said it performed pretty well, sure it was not the most powerful but I was using gas over CO2 so I was not expecting too much, it also shot a bit low for me but again that may have been because of the barrel mod so who really knows for sure at this point ;) And yes it came with that unsightly orange tip that I took short work of removing. At teh end of the day I still love it and it performed well without letting me down, just like a would expect from a real Sig Sauer!
My Vimeo Table Top Review of the Cybergun Sig Sauer P226 GBB Blowback Airsoft Pistol:
Trigger Pull: The trigger pull on the RG-88 and RG-59 in single action is very light with the RG-59 having virtually no take up at all while the RG-88 has some take up but then a noticeable and predictable release point. Both guns have medium to heavy yet smooth double action triggers.
Accuracy: NA.
Build Quality: The overall build quality for the ROHM RG-88 and RG-59 blank guns is excellent, being German made they are built to last and the fit and finish is very good. There are steel parts where they need to be like in the barrel, pins, screws and reenforcing parts, the rest of the gun is generally made out of a zinc metal with only the grips being plastic.
Realism: The ROHM RG-88 and ROHM RG-59 are not exact replicas of any given guns in production as this would make importing them into Canada even more difficult, but they do share similarities with some real guns in production. The RG-88 semi auto looks to be based around a Walther PPK design while the RG-59 has that Smith & Wesson Snub Nosed Revolver look to it. As for looking like and working like real guns, they do this very well, with the exception of the dangerous bullet coming out of the barrel!
German made quality, materials fit and finish is all excellent.
Almost all metal with some reenforced steel parts.
Nice light single action triggers on both guns with double action ability wehn needed.
Both are front firing with semi plugged barrels.
Come with flare adaptors and cleaning rods.
Seem to be some of the only blank guns we can get here in Canada right now.
Cons:
Not actual exact replicas of any specific guns in production.
The RG-59 only works with the .380 crimped, 9mm P.A.K. balnks are a bit too long.
Expensive due to them being harder to get and in high demand in Canada.
Comments:
As with pretty much all blank guns, they are mostly for show so it all comes down to how do they look and do they go bang when they are supposed to! In both cases they get top marks. Both the RG-88 semi auto and RG-59 revolver feel solid and the mechanical parts are tight and smooth giving a confident feeling when holding them. I like the larger caliber blanks over the .22 crimped blanks as they have a bigger bang but they will set you back in the cost department a bit more as the price for 9mm P.A.K. and .380 blanks will be a lot more than .22 crimped so keep this in mind when choosing a blank gun. If you're looking for a well made and dependable blank pistol then you really can not go wrong with any of the ROHM blank guns we sell in the Canada Replica Airguns Store.
My Vimeo Full Video Review for the ROHM RG-88 and RG59 Blank Pistols:
