Propulsion: Green gas or 12 Gram CO2 dependant on magazine used.
Action: Blowback,Single action only.
Ammunition Type: 6mm plastic Airsoft BB's.
Ammunition Capacity: 29 rounds.
FPS: 410-440 fps
Trigger Pull: The trigger pull on the KJWork KC-02 Version 2 10/22 Gas Blowback Airsoft Carbine is pretty much exactly like a real Ruger 10/22, nice and short, not to light or heavy, crisp and single action only. If you already have a Ruger 10/22 and want to pickup this Airsoft version for some anytime shooting then you will not be disappointed in the trigger since it is already what you are used to.
Accuracy: I decided to setup my paper target a little further out than my standard 30 feet, so I took it back to around 50 feet and put around 24 shots into it in a fairly quick succession from a rested position. The KJWork KC-02 Version 2 10/22 Gas Blowback Airsoft Carbine grouped continently and well centred on target getting around a 3 inch grouping. This was using a red dot scope but with the out of the box hop-up setting in place. I was a little bit surprised by my fps results as my Chronograph recorded an impressive 445 average 5 shot fps using the lower powered green gas magazine. All shot where within only a few fps of each other too! I can only imagine how hard this gun would shoot using the alternative CO2 Magazine. Blowback action was just enough to give some feedback and of course allowed for the bolt to cycle giving the KJWork KC-02 Version 2 10/22 Gas Blowback Airsoft Carbine a true single action trigger pull.
Build Quality: The build quality for all KJWork KC-02 Version 2 10/22 Gas Blowback Airsoft Carbine is very good with a nice weight and feel to it, It really does feel like I am holding a real Ruger 10/22 and it is one of the most popular semi auto 22LR rifles out there for a reason. Mechanically this Ryger 10/22 copy works great, super consistent and very responsive. The fit and finish as with all KJWorks guns is top notch.
Realism: The KJWork KC-02 Version 2 10/22 Gas Blowback Airsoft Carbine is for all intents and purposes simple an Airsoft version of the Ruger 10/22 and even though I have no way to confirm this, I would imagine many 10/22 after market accessories may actually work with the KJWork 10/22 Gas Blowback Airsoft Carbine. Everything works just like it would on a real 10/22 without the loud noise and ejecting shells.
Built on the very popular 10/22 platform so lots of people are going to be very familiar with this rifle and may want an Airsoft version they can shoot just about any time they feel like it.
Good weight and feel to it.
Blowback semi auto action with true single action trigger.
Lots of rail access points for tons of add on accessories.
Pop-up fully adjustable sights stay out of the way but are ready to go when needed.
Easy to adjust Hop-up.
Available magazines in both CO2 and Green Gas.
Adjustable AR styled rear stock with AR pistol grips.
Sling mounts included.
Works with standard Airsoft screw on flash hider or suppressors.
Awesome FPS and consistency.
Very accurate even at 50 feet, around a 3 inch 25 shot grouping.
Cons:
No full auto mode.
Higher capacity mag would have been nice.
Would be nice to have a higher capacity magazine for it.
Comments:
I am really impressed with the KJWork KC-02 Version 2 10/22 Gas Blowback Airsoft Carbine! It feel and shoots a lot like the real steel version but with less noise and recoil. For back yard shooting fun and practice you can not find a cheaper gun out there to simulate shooting your real 10/22 and of course this rifle used on an Airsoft field would be a perfect fir for almost any shooting environment since it is light, compact, accurate and powerful. I think I found my newest favorite Blowback Airsoft Rifle :)
My Vimeo Table Top Review of the KJWork KC-02 Version 2 10/22 Gas Blowback Airsoft Carbine:
I try and make it to my local gun show which is held in Chilliwack BC about this time each year. It is put on by the Historical Arms Collectors Society of BC and there are generally a lot of used long guns (rifles) some pistols, lots of accessories, knives, hunting gear, knick·knacks and even some antique items. I tend to be looking for airguns or blank guns that are rare or a good deal.
This year I came across a few items that caught my eye. The first item was a Daisy replica 4.5mm BB pistol, I am not a big fan of Daisy replica gun in general as they are usually a far cry from the originals but this Daisy Powerline Model 400 was actually a really good copy of a Desert Eagle in size and looks. Sure it had a lot of plastic in it but it was made in Japan and even being around 20 years olds was holding up really well. This Daisy Powerline 400 even had Blowback which back then was not all that common.
The Daisy Powerline 400 BB Desert Eagle has a 20 round removable magazine that fits along the top of the barrel and it has a claimed fps. It is almost all high grade plastic with the exception of the single action only trigger, safety, hammer, barrel and several internal parts.
The next interesting item I found was a little compact 8mm blank shooter originally made in West Germany. So this blank gun is close to 30 years old. The SM Model 110 8mm Blank Pistol kind of reminds me of my EKOL Tuna in terms of size and functionality since both have the same half slide and magazine release system.
The SM Mod 110 8mm Blank Pistol is front venting and pretty much all metal with reinforced steel areas, it has a 5 round single stack magazine and shoots in single action only.
My last purchase for this show was a new item, here in Canada we generally are not allowed much in the way of items specifically labeled for self defense. There are some work arounds for instance we can carry a knife as long as it is not concealed entirely and we only intend to use it as a tool. We can also carry pepper spray again only for use on animals. Generally speaking we have not been allowed stun guns or tasers here in Canada and even importing them can land you in a lot of trouble! Again it seems a work around has been made, as long as the Stun Gun or Taser is at least 480mm in length then it is not considered a concealable weapon and as long as you have it out on display and only intend to use it on animals that may be a threat to you then all is good :)
The Stun Gun I purchased is basically a baton with a flashlight on the front and a 1 million volt taser on the front of it. You have several options with this device if harm is eminent. You can try blinding the threat with the built in flashlight which is not all that powerful but good for finding your way in dark areas, you can give the attacker a whack with the baton baseball bat style and if none of that is working well let em have the 1 million volt sandwich! We should be getting some of these Stun Baton Flashlights in our Canada Replica Airguns Store at some point so stay posted for that item.
I am showcasing here on the Replica Airguns website and over on the Replica Airguns YouTube channel a series of videos I am making for the purpose of selling some guns out of my personal collection. I simply have no more room for the new guns and in some cases I either have duplicate guns or very similar versions so there is no need to have both. Some guns I am less attached to and as I already stated I need to make room for some of the new stuff I will be reviewing and or buying for myself.
In this third Mike's Personal Guns For Sale video I am offering four BB rifles, three of which have full auto or at least burst mode ability and the fourth BB rifles is more of a Shotguns with the ability to shoot three BB's at once. Most of these BB rifles are really hard to get here in Canada now since one is not made anymore and the two are simply not currently being imported into Canada.
Make sure to watch my above YouTube video to see these four BB rifles I am selling and instructions on how you can take part in the sale and purchase of them. By the way I am only selling to Canadian residents since shipping cross borders is a little sketchy.
Here is a list of the BB Rifles I am selling from my personal gun collection:
I am showcasing here on the Replica Airguns website and over on the Replica Airguns YouTube channel a series of videos I will be making for the purpose of selling some guns out of my personal collection. I simply have no more room for the new guns and in some cases I either have duplicate guns or very similar versions so there is no need to have both. Some guns I am less attached to and as I already stated I need to make room for some of the new stuff I will be reviewing and or buying for myself.
In this second Mike's Personal Guns For Sale video I am offering three rifles, two of which will require a Canada PAL Firearms License since one is a 22LR rimfire rifle and the other is a high powered .22 caliber break barrel pellet rifle. The last item up for bid is an AK-47 styled .68 caliber paintball rifle.
Make sure to watch my above YouTube video to see these three rifles I am selling and instructions on how you can take part in the sale and purchase of them. By the way I am only selling to Canadian residents since shipping cross borders is a little sketchy.
Here is a list of the these three rifles I am selling from my personal gun collection:
In this 2016 SHOT Show Interview I talk with Chip Hunnucutt from Crosman Corporation. Chip was eager to show off Crosman's new Airbow which is a essentially a hybrid PCP Air Rifles combined with a Crossbow. SO take away the bow and replace the power source with a 3000 PSI compressed air system that is capable of shooting standard archery arrows at 450 fps with 160 foot pounds of energy using 375 grain arrows.
The Crosman Airbow on a full 3000 PSI charge can deliver 8 consecutive shots @ the regulated 450 fps. The Airbow also weighs in at 7 pounds and being that it is a Bullpup design it is only 33.5 inches long so nice and compact for an arrow shooter.
Since the power is generated by the PCP compressed air system there is no heavy cocking rope so a simple lift of the ambidextrous cocking bolt is all that is needed to charge the Crosman Airbow. The Airbow also comes standard with a CenterPoint® 6x40 mm scope specially designed with the Airbow in mind.
Since the Crosman Airbow is technically an under 500 fps airgun, it should be considered an uncontrolled firearm here in Canada which means no PAL license will be required to buy and own the Crosman Airbow in Canada. In terms of using the Airbow for hunting as it is not a bow but rather an Airgun, that is yet to be determined here in Canada.
In this 2016 SHOT Show Interview I talk with Bob Li from Action Sport Games. Bob shows me some of the new products this year from ASG. Some of ASG's newer pistols are the Dan Wesson 715, the CZ 75 SP-01 Shadow, the CZ P-09. New to the rifle line is the CZ Bren 80, also a couple of sniper rifles, the M40A5 and M40A3. ASG is also coming out with a an Inferno HPA version of their CZ Scorpion EVO 3A1.
The ASG Dan Wesson 715 has ot me my favorite product from ASG, you need to hold it in your hand to really understand how solid this pistol really is at close to 3 pounds. Everything about it is an improvement over previous Dan Wesson models including the trigger and hammer action, crane setup and the more actuate frame length with the new more compact internal CO2 valve. The ASG Dan Wesson 715 will be shipping in 4.5mm Steel BB, 6mm Plastic Airsoft and .177 caliber pellet versions.
ASG's two new Full blowback CZ 75 SP-01 Shadow, the CZ P-09 pistols should be coming out shortly, both will be available in 4.5mm Steel BB and 6mm Plastic Airsoft. Both pistols feature a metal slide and frame with full size drop out metal magazines and will have CO2 and Green Gas magazine configurations. The CZ P-09 will have a threaded barrel and barrel protector.
In this 2016 SHOT Show Interview I talk with Dani Navickas from the Airgun division of Sig Sauer. Dani and I discuss Sig's new line of CO2 Blowback Pellet rifles and pistols. Dani talks about some of the behind the scenes information that went into the development and manufacturing of Sig's new line of CO2 Airguns.
Sig CO2 P226 and P250 Air Pistols along with their Sig MPX and MCX Air Rifles have been developed in house by Sig.Sig has been working very closely with a Japanese manufacturer to make sure that every stage of development is to Sig's high standards. The new Sig CO2 Blowback rifles and pistols are made to match the real steal version in almost every way including dimension, weight, functionality, materials used and even trigger pull.
Sig's new Sig MPX and Sig MCX Pellet Rifles have a brand new patented belt fed 30 round pellet magazine that is indexed via the internal blowback action of these rifles smoothing out the trigger action. The Sig P226 and Sig P250 pistols use a double ended 16 round pellet magazine similar to what you would find on Umarex's PX4 Strom blowback pellet pistol.
Look for Sig's new line of CO2 Blowback Pellet Airguns coming out shortly.
This is my SHOT Show 2016 Teaser Video! You will get to see some new gun highlights from companies like Umarex, ASG, Crosman, Sig Sauer, KWA and ISC. I will be following up this video with some interview videos very soon so do make sure to check back for those uploads. All I can say about the show is it’s huge! So much to see, so much walking and too much to take in…
ASG:
As always, ASG had some new products this year. The all new Dan Wesson 715 357 Magnum shell loading Revolver! This gun feels absolutely amazing in the hand and will be available in Steel BB, Airsfot and even Pellet shooting versions. Also new are the CZ P-09 and CZ 75 SP-01 Shadow Full Blowback BB and Airsoft Pistols.
Crosman:
Big at Crosman this year was their PCP Airbow, Crosman put a lot of focus on this product and even had a lot of crossbows on display to go with their new PCP Airbow. Crosman also introduced their low cost entry level Benjamin Maximus PCP rifle in .177 and .22 calibers offerings. Not really much in the way of replica pistols from Crosman this year, but then again last year was kind of the same?
Sig Sauer:
I finally made it to the Sig Sauer Booth this year to checkout their new CO2 Pellet gun line. All new Sig Airguns are made true to size and weight with similar trigger actions as their real steel versions. The Sig MPX is their more compact (shorter barreled) pellet shooting CO2 rifle with internal blowback and belt fed 30 round magazine. The Sig MCX is the longer barreled rifle version but built much the same as the MPX. Sig also introduced two new pellet shooting CO2 Blowback Pistols, the P226 and the P250. Both use similar double ended rotary magazines as the Umarex PX4.
Umarex:
Umarex always seems to have some new exciting Airguns products to offer at SHOT Show. The PPK is back with a few updates including no more ugly CO2 tab sticking out of the bottom! And yes the Beretta Model 92A1 will finally be shipping soon, I believe in February! My favorite product this year from Umarex would have to be the Full Blowback, Full size drop out magazine S&W M&P 40 CO2 BB Pistol. Umarex released yet another 1911 on the market, this version does come with a stick mag and sports pretty high fps and more shots per CO2 then the KWC based 1911’s. The super popular Colt SAA Revolver is now available in a pellet shooting version with a rifled barrel :) Umarex had on display another low cost revolver, the ultra futuristic looking Brodax CO2 BB Revolver.
KWA:
KWA always has really nice high quality products to showoff at there booth each year, we may even start carrying some of KWA's products this year, fingers crossed on that one… New to the KWA line are some AEG rifles with simulated blowback action, I really liked the Blowback AEG AK they had on display. KWA also released a new Airsoft shell loading revolvers that had some of the nicest looking brass and aluminum shells. On display under a glass cover was a very solid Gas Blowback Thompson Machine-gun with real wood stock, it was absolutely gorgeous!
ISC:
ISC known for their top quality AEG internals, had their full line of high quality Airsoft rifles on display. And new this year to ICS was their first ever Airsoft pistol, the blowback BLE Alpha. The BLE should be out mid year and looked and felt really nice. The trigger on it was super short and light.
I have some really awesome Interview videos I’m working on, I will be uploading them shortly so stay tuned for those…
When I say Airguns, I am referring to pretty much all BB, Airsoft, Pellet, Paintball and even Blank guns for most of the topics listed here.
Do’s:
Treat your Airgun just like you would a real gun. If something goes wrong, perhaps the outcome will not be as severe but do you really want to take a trip down to your local emergency ward to get a BB or Pellet removed?
Always assume your airgun is loaded, for some reason it always seems those empty guns are the ones that do the most damage.
Be discrete, If it looks like a gun other people will think it is a gun so don’t flash your airguns around in public. Keep it in a case when transporting and shoot it in an area that will not alarm other people.
Always wear eye protection when shooting your Airgun. Do you really want to shoot your eye out? No Joke!
Be aware of your surroundings like windows, hard objects that could make your ammo bounce back at you. Make sure you are shooting your Airgun in a safe direction at all times, know your target and beyond.
Use Airguns to teach others and learn how to safely and effectively shoot a gun. Airguns can be less intimidating then a real gun (Not so loud and very little recoil) and make for great start out and transitions guns.
Use Airguns to get more inexpensive trigger time and become a more experienced shooter. Airguns cosy only pennies per round to shoot and can be shot in way more areas than a real gun can, practice makes perfect so get shooting!
Use Airguns in areas where real guns may not be allowed or safe to use. Again, Airguns can be shot in all kinds of places, in your back yard or even in a properly setup indoor home range.
Use Airguns with adequate power for safe and humane pest control where real guns may be prohibited.Airguns are quiet and less likely for the bullet to travel long ranges which makes them ideal for close range pest control in areas where real guns are too loud and to powerful.
Don’ts:
Do not assume because it is an airgun it is not dangerous or simply a toy. Many Deaths have been caused by Airguns along with a lot of pain and suffering so treat your Airgun with respect. It is not a toy or you would find them in the toy department at your local store along with yo-yos and stuffed animals.
Do not point or shoot at people unless of course you are using an Airsoft gun in an Airsoft field or facility. Yes Airsoft guns are meant to shoot at each other (with appropriate attire like eye protection and full body clothing), but steel BB and Pellet can cause serious injury especially at close range and on direct skin contact.
Do not leave your Airgun loaded, you never know who is going to come across it and accidentally discharge it. Remember, a loaded gun is a dangerous gun in the wrong hands. You may know better than to assume the gun is undulated but children and even adults without any gun training will most definitely handle the airgun without consideration of the danger it poses.
Do not use an Airgun for self protection. See my related video. Simply put, Airguns are not practical for self defense because they rarely have enough Stopping Power. The ones that do have enough power need to be pre-charged and in most cases are only single shot meaning if you miss or don’t get the job done no the first shot then you are done.
Do not use an underpowered Airgun for pest control. See related video. Using a low powered BB pistol for pest control is cruel, you will only injure the animal making it suffer unnecessarily. Use a high powered pellet rifle to get the job done.
Do not take your gun apart, in most cases this will void the warranty and the reality is that airguns rarely need to be cleaned since no dirty gun powder is used. lead pellet rifles may require occasional barrel cleaning to keep the rifled barrel free of debris.
Do not over oil your Airgun, a little goes a long way and too much oil will just attracted dirt, use the right airgun oil and just enough to keep part functioning smoothly.
Do not over pump an Airgun. Over pumping an Airgun can cause damage to valves and seals and in a worse case situation a rupture the air pressure reservoir or even cause the airgun to explode!
Can I use Airsoft BB's in my BB Pistol? I would have to say this is by far the number one question I get asked in the comments section of my Vimeo videos. I have made several videos where this question gets addressed within the video but so far to date I have not made a stand alone video just covering Airsoft BB use in BB Guns.
So here it is, and now I have a video I can link to this so very common question, if you where wondering about this yourself than please watch my YouTube Video on this topic as it goes into a fair amount of detail about it.
The short answer to this question is no, you can not use 6mm Airsoft BB's in a 4.5mm Steel BB Pistol or Rifle. For the simple reason that 6mm is larger than 4.5mm and so the physical diameter of a6mm Plastic Airsoft BB is just to large to fit inside of a 4.5mm Steel BB magazine or barrel.
People have commented about using a 4.5mm plastic Airsoft BB in a 4.5mm BB gun and yes this could in theory be an option but I discuss why I feel this is not a good idea based on size and mass.
I'm getting close to uploading 600 videos now over on the Replica Airguns Vimeo channel, so there are bound to be a lot of similar questions and popular discussions. In this Replica Airguns Vimeo Video I address what I feel are my Top 10 Most Common Airgun Questions and Discussions.
Trigger Pull: The trigger on the G&G GR14 Type 57 R.O.C. is like most AEG Airsoft Rifles, being that it is essentially an electric on off switch and not a mechanical one. So it is light with not much take up. You will notice a bit of delay from the time your press the trigger till a BB is released since the electric motor must first pull back the spring and release it.
Accuracy: So far I have not tested out the G&G GR14 AEG Type 57 R.O.C. Walnut Wood Stock Airsoft Rifle. When I get the chance, I will have to set my paper target up further out than my usual 30 feet! I am also expecting the fps to be a bit higher than the stated factory default since this G&G GR14 AEG Airsoft Rifle is marked as being the "High Muzzle Velocity Version"! Stay tuned for my future Field Test Shooting video for the G&G GR14 AEG Type 57 R.O.C. Walnut Wood Stock Airsoft Rifle.
Build Quality: The G&G GR14 AEG Type 57 R.O.C. Walnut Wood Stock Airsoft Rifle looks to extremely well made with most of the build materials being metal and wood. The only none metal or wood noticeable parts would be the upper hand guard which is made out of some sort of nylon or plastic. I believe the original M14 Rifle upper hand guard was made out of fiberglass. Then Walnut Wood Stock is nicely finished and the metal parts function and look really great.
Realism: In terms of realism the G&G GR14 AEG Type 57 R.O.C. Walnut Wood Stock Airsoft Rifle is extremely authentic in terms of looks, weight and even overall length and barrel length! Most of the parts operate exactly as they would on the real M14 rifle including the selector switch, safety, magazine release, shoulder rest adjustable sights and bolt.
Lots of metal and wood parts where they would be on the real M14.
True realistic 9 pound weight.
High capacity magazine at 470 rounds.
Sights are adjustable for elevation and windage.
Semi and Full Auto selectable.
Real Walnut Wood Stock.
Flip up metal shoulder rest.
Engraved with "The Republic of China" Chinese Text Markings.
25000 rpm Hi-torque Long axis Motor with 7/8 mm Bearings.
8.4v Large Tamiya Battery System.
Cons:
Does not come with battery or charger.
Not setup as is for a scope.
Comments:
History of the M14 this rifle is based on - "The M14 rifle, formally the United States Rifle. M14 is an American selective fire automatic rifle firing 7.62x51mm NATO (.308 Winchester) ammunition. It was the standard issue U.S. rifle from 1959 to 1970. The M14 was used for U.S. Army and Marine Corps basic and advanced individual training and was the standard issue infantry rifle in CONUS, Europe, and South Korea, until replaced by the M16 rifle in 1970."
So the M14 has a place in our history books and also a place in many of our war veterans hearts. This G&G GR14 AEG Type 57 R.O.C. Walnut Wood Stock Airsoft Rifle replica is an excellent example of such a great piece of history, to have one in a working Airsoft version may be the next best option to having the real deal.
My YouTube Review Video of the G&G GR14 AEG Type 57 R.O.C. Walnut Wood Stock Airsoft Rifle:
Whether you like it or not, most of us have come across an Airgun with an ugly orange tip on it at some point. In most cases you will find the intrusive orange or red tips on Airsoft guns that shoot plastic BB's, in some cases you will even find them on Airguns that shoot either lead pellets and/or steel BB's.
It really comes down to where you live as to what your local gun laws have determined is required for your area. You may even live in a region where Airguns and Airsoft guns are not allowed at all! So for you a red or orange tip on the front would be welcome if it would allow you to own an Airgun or Airsoft gun. What about the entire gun being painted a bright color, well that is the case for some folks so again having a red or orange tips may not be as bad as it originally seemed...
In Canada where I live, we used to only be allowed Airsoft guns that had clear sections as our replica gun laws are very strict and all black Airsoft guns would have fallen iinto the "replica" category if they did not have large clear plastic see-through sections on them. This clear section law was revised somewhat over the last several years to allow for all black Airsoft guns here in Canada. It was determined that many Airsoft guns with higher fps limits could cause a serious injury to a human, making them less of a toy in the eyes of the law and more of a weapon. Because of this, Airsoft guns that are capable of shooting a .20 gram plastic BB at a velocity of 360 fps or "higher" are now considered to be similar in the eyes of the law to a regular steel BB or lead pellet shooting Airgun. In Canada, Pellet and Steel BB guns are actually considered firearms of a sort so this allows the higher fps Airsoft guns to be all black since it can not be a replica of a firearm if it is in fact considered to be a firearm by law.
The long and short of all of this is that here in Canada we do not require our Airsoft guns to have orange or red tips since they are considered more or less to be just like any other Airgun and our Airguns do not have red or orange tips either.
Getting back to the title of this article "No Orange Tip On Your Airsoft Gun! Are You Insane?" I often get folks from the US giving me heck for removing the orange tips from my Airsoft guns or asking me why my Airsoft guns don't have them in the first place. These people even state that I could get in a lot of trouble for this! Perhaps they think I live in the US or that US laws govern Canada as well? I am not sure but I can say for the record that I am not breaking any laws at least here in Canada where I live.
I know in the US that wholesalers and retailers by law have to sell Airsoft guns with the affixed orange tips on them, once the end user receives that gun and depending on which state they live in, it may or may not be legal to remove the orange tip. Again, you will need to look into your local state laws as they are different from state to state in the US.
In this Video Review I show you around the G&G CM16 Raider and Carbine AEG Airsoft Rifle's. Since these AEG Airsoft AR Rifles are a bit large to showcase using my traditional Table Top location I move into my gym and take each gun out of its box to have a good look at them. I talk about some of the main features and specification. The main features being these G&G CM16 AR15 / M16 AEG Airsoft Rifles are all really well priced but also very well made for their rather low overall cost. They do have a primarily all Nylon Fiber build even in the receivers but they still have a nice 4.6 to 5.7 pound weight to them, and once dressed up with a few accessories they come in at a perfect weight that is not too heavy to carry around in just about any game situation. The Nylon material in some way is a better choice in terms of getting scratched and dinged since they will not mark up as easily as painted metals will.
I don't often review target and or hunting rifles since for the most part Replica Airguns is all about well... replica airguns :) I have reviewed some of my own personal spring piston and pump rifles since I have them and there is a cross over in folks that like both the replica airguns and airguns meant for target and or hunting purposes.
We do have a small selection of spring piston rifles in our Replica Airguns Canada store suitable for target and small game so I thought I would point some of them out in this preview video.
To everyone else that entered. I want to thank you all for taking the time to come up with this years costume, make a video and send me the link. This year we only had 10 entered so the chances of winner where pretty good. Make sure to checkout all of this years entry videos! Next year let's get more people on board and make this contest even more fun!
Watch my Halloween Costume Contest Giveaway 2015 Winner YouTube Video:
Watch Gary Vennarucci's Virginia City Nevada Gunslinger and Madams YouTube Video:
Again I wanted to mention we are having a Halloween sale in our Canada Replica Airguns Store from Thursday October 29th till Sunday November 1st 2015 so don't miss out on this one!
On Saturday I went to a Halloween House party, my Brother in-law and his wife put on a Halloween party pretty much every year, usually a week before which works out great for me since I have kids and Halloween night is usually reserved for them.
Getting dressed up a week before is great since it gives me the opportunity to record a video of me in my final completed Halloween outfit so I can share it with all of you. Even though I don't get to complete in the Replica Airguns Annual Halloween Costume Contest Giveaway, at least I get to have some fun and dress up :)
So enjoy my Rambo Costume this year and if you want to know what was needed to pull off this Halloween Costume then watch this video.
If you're interested in getting involved in this years Replica Airguns 2015 Halloween Costume Giveaway then watch this video.
Before I get into the detail of my Rambo Costume this year I wanted to mention we are having a Halloween sale in our Canada Replica Airguns Store from Thursday October 29th till Sunday November 1st 2015.
Continuing on with the Halloween Theme... this YouTube video showcases my Rambo Halloween Costume components. I will be dressing up in full costume and sharing the video very soon but wanted to show you al my Halloween Costume bits and pieces most of which I already had which made my costume pretty easy and low cost this year :)
So what does one need to be Rambo for Halloween?
Some heavy duty black boots for sure and beat up is better.
You pant choice could be jeans, camo or all black depending on which movie Rambo you pick, I went with Black cargo style pants and an olive green belt.
You are going to want a dark color wife beater (tank top) as this is a classic Rambo attire, another option is to go shirtless if you are brave enough to do so :)
I would imagine most people are not going to have that 80's long hair so you will probably need some sort of a dark brown curly or wavy wig. I figure the bigger the hair the better. To keep all that hair out of your eyes, Rambo often wore a headband in either black or red, this will also help keep the wig in place.
In terms of weaponry a large kick-ass knife should be strapped to one leg and for firepower, go with bigger is better and a classic trusted machine gun like the AK or M60.
One optional item you can add to your Rambo Halloween Costume all be it one I plan to go with is an Ammo Belt because there simply is never too much ammo!
Finish off the entire package with a few days worth of stubble and some makeup to give you that been through hell dirty and bloodied up look.
It's that time of the year again and time for the annual Halloween Costume Contest Giveaway!
I love watching all your video entries and this year it will be pretty much the same as last year so make sure to get your Halloween Costume entries in before the November 10th deadline.
Here are the rules:
First and foremost make sure to have fun!
Your costume needs to have some sort of a weapon in it but it does not have to be a gun or even a knife or sword, it could be a bat, axe, hammer, chain saw... The more creative the better!
Upload and share your Halloween Costume video response before midnight November 10th.
What is the big prize!
Your choice of KWC or Cybergun (depending on if you are in Canada or the US) full blowback pistols. (Sig X-5, P92, 1911) I am also including some revolver choices, pretty much any of the ASG Dan Wesson's and also the Umarex SAA Peacemakers in either Black or Nickel. Your choice of 4.5mm Steel BB or Airsoft also dependant on what is in stock and available at that time.
Materials: Metal and plastic (polymer) construction.
Weight: 5.3pounds (2400 grams).
Length: Open 24.8 inches (630mm) - Closed 15.6 inches (395mm).
Propulsion: AEG.
Action: Semi and full auto.
Ammunition Type: 6mm Airsoft BB's
Ammunition Capacity: 100 round magazine.
FPS: 312+.
Trigger Pull: The trigger pull on the ASG B&T BT5 PDW 6mm AEG Airsoft Gun is what you would expect from most AEG Airsoft guns since it is basically an on off switch for the electric circuit. It is fairly light and relatively short. As with most AEG Airsoft guns there is a noticeable sight delay from the time you press the trigger till the gun actually fires a BB since the electric motor must first pull the spring plunger back and then release it to fire a round. Higher output batteries will make this less noticeable since the electric motor will run much quicker.
Accuracy: At this point I have not yet tested the ASG B&T BT5 PDW 6mm AEG Airsoft Gun so I do not have any Chronograph fps velocity or paper target accuracy information to provide to you. I plan on performing my Field Test Shooting Review fairly soon so stay posted for that.
Build Quality: The ASG B&T BT5 PDW 6mm AEG Airsoft Gun is a Chinese made Airsoft gun but I have to say it looks and feels really well built in general. I would say easily as good as any Taiwanese gun I have come across! The fit and finish both are excellent and there is a ton of metal in this gun including the main frame, sights, but plate, charging handle, barrel extension, sling mount and magazine release.
Realism: The ASG B&T BT5 PDW 6mm AEG Airsoft Gun is is very true to scale, size and weight to that of the real steel MP5 PDW as far as I can tell without actually having a real MP5 PDW in my hands . I am pretty sure Brügger & Thomet does not actually have an MP5 version in their product lineup or as this ASG model is named BT5 rather than MP5? That said the ASG B&T BT5 PDW 6mm AEG Airsoft Gun is really simply a replica of an HK MP5 PDW and based on that, it's really close in almost every way.
Lots of metal parts for good overall weight and feel.
Semi and full auto selectable.
Comes with battery and charger.
Folding stock.
Adjustable rear metal sight.
Working Cocking Handle
B&T Licensed.
Cons:
No blowback.
Does not come with rail clamp.
Would of liked a longer higher capacity magazine.
Mine had the wrong charger.
Comments:
I am really looking forward to performing my Field Test Shooting review for the ASG B&T BT5 PDW 6mm AEG Airsoft Gun and hope it performs as good as it looks and feels. I really like my 4.5mm Steel BB Umarex HK MP5K PDW but find it to be a little bit on the lighter side since it is mostly plastic. The ASG B&T BT5 PDW 6mm AEG Airsoft Gun fixes that problem with it's mostly metal build and I also get the added benefit of having full auto that is missing from the Umarex version.
Watch my Vimeo Table Top Review of the ASG B&T BT5 PDW 6mm AEG Airsoft Gun:
