Type: Airsoft Rifle. Distributer:ASG. Model:Steyr Arms Scout. Materials: Metal and polymer build. Weight: 6.5 pounds (2950 grams). Barrel: 14.5 inches (368mm), non-rifled. Total Length: 39.5 inches (1000mm) Propulsion: Spring Piston Action: Bolt action repeater. Ammunition Type: .6mm plastic Airsoft BB’s. Ammunition Capacity: 32 round magazine. FPS: 443. Type: Black and Grey versions.
Trigger Pull: The trigger pull on the ASG Steyr Arms Scout Bolt Action Spring Airsoft Rifle is short light and crisp. Working the bolt precooks the trigger for single action only shooting allowing for just the release of the hammer. There is very little take up and no creep at all, just a nice light and predictable trigger pull.
Accuracy: I have not performed my Field Test Shooting Video for the ASG Steyr Arms Scout Bolt Action Spring Airsoft Rifle so stay posted for that. ASG claims around 4430 fps velocity with the preinstalled M140 spring, you can upgrade the spring all the way up to an M190 spring for even higher potential fps. In terms of accuracy I am also expecting good results so check back next week for my Indoor Field Test Shooting Video for the ASG Steyr Arms Scout Bolt Action Spring Airsoft Rifle.
Build Quality: The ASG Steyr Arms Scout Bolt Action Spring Airsoft Rifle is well built with lots of high quality component not only inside but also internally. You will find a metal barrel and receiver along with metal bolt, trigger and rear sight, the front sight is however plastic. I donate really thin k you will be using the pop sights all that much as they are not adjustable and this gun really begs for a nice optical scope. The nylon polymer stock has micro-texturing to help with the grip in all weather conditions.
Realism: The ASG Steyr Arms Scout Bolt Action Spring Airsoft Rifle is based on the real steel 7.62 NATO Steyr Scout and even incorporates the integrated folding bipod legs like the original. For the most part they look identical but you will find the actual magazine on the Airsoft version is placed further up the stock to allow for the feeding of the Airsoft BB’s which does make the actual inner barrel shorter by about 4-5 inches.
Pros:
Nylon Polymer stock with micro-texturing.
Railed metal receiver with laser-etched Steyr trademarks.
Integrated folding bipod legs on left and right sides of the stock.
Flip-up backup front and rear sights.
Accessory slot on bottom of stock for mounting of optional bipod rail.
Millet QD sling loop attachment points.
Front dummy magazine.
Rear dummy magazine with storage for a spare magazine.
Removable stock spacer pads for length-of-pull adjustment.
90 degree trigger with steel sear.
90 degree aluminum piston with dual glide rings and steel base.
Silent Air Brake piston head.
Silent cylinder head with shock-absorbing padding.
9mm stainless steel ball bearing spring guide.
Bore-up steel cylinder with 12.5% more air volume than stock cylinders.
Hop-up unit with both side-lever adjustment and TDC screw adjustment options.
Steel CNC-machined hop-up arm.
03mm tight-bore inner barrel.
60 degree Modify Predator enhanced hop-up bucking preinstalled (50 and 70 degree buckings available separately).
Compatible with VSR-spec inner barrels.
450 FPS with pre-installed M140 spring.
Can take up to a M190 spring with no upgrades needed.
Cons:
32-round magazine.
Recommended ammo: 0.36g BBs and above, 0.4g optimal.
Comments: I am looking forward to performing my Indoor Field Test Shooting Video for the ASG Steyr Arms Scout Bolt Action Spring Airsoft Rifle. I won’t be able to test it out perhaps as far range as I would like to since I will be shooting it in the Replica Airguns Indoor Shooting range which allows me to test at 30 feet. That should give me a good overall idea on at least what it may be capable of since if we can get a tight group at 30 feet we should also be able to get a tight group at longer ranges with proper hop-up and heavier BB selection. I do plan on placing a scope on the ASG Steyr Arms Scout Bolt Action Spring Airsoft Rifle to give it the best possible chance of performing at it’s best and really hope to see a good result from it.
My Vimeo Videos for the ASG Steyr Arms Scout Bolt Action Spring Airsoft Rifle:
In this Field Test Shooting Video I put the ASG Action Army T-11 Spring Powered Bolt Action Airsoft Gun through it’s paces by first testing out the velocity placing several rounds through my Chronograph, and then I setup a paper target downrange and place 10 rounds into it to see how tight of a grouping I can get. If you have not already watched my Table Top Video for this Airsoft Sniper Pistol/Rifle then make sure to do so for more details, specifications and close up video.
Starting off with my real world velocity test for the ASG Action Army T-11 Spring Powered Bolt Action Airsoft Gun, I decided to use .28 gram Airsoft BB’s for this entire Field test Shooting video so I was expecting to get somewhere between 20-25% slower fps velocity as compared to the standard tested .20 gram Airsoft BB’s. After placing around 6 shots through my Chronograph I averaged 328 fps which ended up being 18% slower than the claimed 400 fps made by ASG. I would image if I had used .20 gram Airsoft BB’s I may have even exceeded 400 fps.
Moving on to the accuracy portion of my Indoor Field Test here in the Replica Airguns Sea Can, as always I placed a fresh paper target 30 feet downrange and proceeded to shoot 10 rounds into it from a rested and seated shooting position to allow for best possible results with as little human factor added in. I was using a 4x optical scope since the ASG Action Army T-11 Spring Powered Bolt Action Airsoft Gun does not come with any type of sighting system included so I did have to sight it in initially. I did manage to get a nice 1.5 inch grouping fairly close to the bullseye but I did notice that if I angled the barrel down a bit, BB’s would roll out of the barrel which made me wonder if the hop-up was set high enough to engage a BB.
So I did my second test with the hop-up set in the middle range and this time BB’s did not fall out of the barrel when angled down. After the hop-up adjustment I did notice I was shooting a bit higher which is expected with more hop-up adjustment so if you are experiencing BB’s falling out of the barrel then make sure to adjust your hop-up a bit tighter.
All in all the ASG Action Army T-11 Spring Powered Bolt Action Airsoft Gun performed very well for me especially once I got the hop-up figured out. And I do think it makes for a really nice compact Sniper Rifle if bulkiness is a factor for you, if not then checkout the Rifle version of this gun with the more traditional but-stock and longer barrel.
Type: Airsoft Rifle. Distributer:ASG. Model:Action Army T-11. Materials: Metal and polymer build. Weight: 3.9/4.5 pounds. Barrel: 11.8 inches, non-rifled. Total Length: 34.7/43.3 inches Propulsion: Spring Action: Bolt action repeater. Ammunition Type: .6mm plastic Airsoft BB’s. Ammunition Capacity: 50 round magazine. FPS: 400-430. Type: Pistol and Rifle versions.
Trigger Pull: The trigger pull on ASG Action Army T-11 Spring Powered Bolt Action Airsoft Gun is light, short and crisp. There is virtually no take-up and the release point has no creep to it. I would say it is not too light but for sure one of the lighter trigger s I have tested on a Airsoft rifle.
Accuracy: I have not performed my Field Test Shooting Video for the ASG Action Army T-11 Spring Powered Bolt Action Airsoft Gun so stay posted for that. ASG claims around 400-430 fps velocity depending on the version which is kind of weird since both have the exact same barrel length internally and I would assume both use the same mechanical part throughout? I don’t have the rifle version to compare to but I will for sure test the velocity using my Chronograph for the pistol version when I do my Field Test Shooting Review along with accuracy performance.
Build Quality: The ASG Action Army T-11 Spring Powered Bolt Action Airsoft Gun is well built for sure, it feels really solid in the hadn't and has good overall weigth to it for it’s size. You will find lots of metal parts where they need to be as in the inner and outer barrel, receiver, bolt, trigger, magazine release and I am sure most mechanical internal parts. Fit and finish is also very good.
Realism: The ASG Action Army T-11 Spring Powered Bolt Action Airsoft Gun is not a replace of any gun I know of but does have tab least the pistol version does look like a sawn off shotgun more than a sniper rifle. The gun overall all is very modern and ergonomic looking but in terms of being a replica of any specific real steel gun in production I don’t know of any it would resemble?
Pros:
Top and bottom rails for lots of accessory add on options.
Can swap over to a rifle version by adding on an interchangeable but-stock.
Mock magazine allows for storage and transport of tools plus extras.
Safety switch is in a great location for right handed shooters.
Comes with included hand stop.
Solid construction with lots of metal parts where they are important.
Ability to add side rails.
Great option if you are looking for a more compact sniper rifle.
Comes in Pistol and Rifle versions.
Cons:
Has an orange tip.
Does not come with sights, will need to add some sort of optical or red dot sight.
Does not come with speed loader, would have been nice.
Comments: I am looking forward to performing my Indoor Field Test Shooting Video for the ASG Action Army T-11 Spring Powered Bolt Action Airsoft Gun. I won’t be able to test it out perhaps as far range as I would like to since I will be shooting it in the Replica Airguns Indoor Shooting range which allows me to test at 30 feet. That should give us a good overall idea on at least what it may be capable of since if we can get a tight group at 30 feet we should also be able to get a tight group at longer ranges with proper hop-up and BB selection. I like the option of being able to choose either the Pistol or Rifle version and both should perform about the same. Having the Pistol version will allow for a much more compact Sniper Rifle option much better suited for shooting in a variety of situations.
My Vimeo Videos for the ASG Action Army T-11 Spring Powered Bolt Action Airsoft Gun:
Make sure to watch my Table Top Video Review where I go into more detail about the specifications and details along with some nice close up video of the Umarex Fusion 2 CO2 .177 Caliber Bolt Action Pellet Rifle.
In this Vimeo Video Field Test Review I test out the Umarex Fusion 2 CO2 .177 Caliber Bolt Action Pellet Rifle in the indoor Replica Airguns Shooting Range to see how accurate it is and what kind fo velocity we can expect from it.
Starting with the velocity test I averaged out 8 rounds through my chronograph using 8.18 grain lead pellets using the dual 12 gram CO2 setup and I was able to average 445 fps which is not bad as these are mid grain weight pellets, lighter weight pellets would for sure get closer to the 490 fps claimed by Umarex. The temperate was about average room temp so not overly cold or warm.
Moving on to the accuracy test I placed all 9 rounds from the rotary magazine into a fresh paper target setup 30 feet away. I use a reseted seated position in the back with the Umarex Fusion 2 CO2 .177 Caliber Bolt Action Pellet Rifle resting on a sand bag up front and I was using the 4 power scope for this test which I setup earlier. My final result was for sure an under one half inch grouping, I did feel like I pulled one shot a little bit but I am sure this Airgun can get quarter inch groupings at 30 feet and I would expect half inch groupings at 50 feet so perfect for mid range small pest shooting.
Umarex does adversities this Air rifle as being very quiet but in Canada we are not allowed to have any type of suppressor even on airguns so I believe this Canada version has been disabled in that regard but the Umarex Fusion 2 CO2 .177 Caliber Bolt Action Pellet Rifle is fairly quiet for sure with its long barrel and slightly lower fps than the US version. Overall the Umarex Fusion 2 CO2 .177 Caliber Bolt Action Pellet Rifle is a lot of bang for the buck with the added 4x scope, included magazines that hold 9 rounds each and the ability to use either a dual 12 gram or single 88 gram CO2 setup. It also looks really cool and performs just as good!
Type: Pellet Rifle. Distributer:Umarex. Model:Fusion 2. Materials: Metal and polymer build. Weight: 6.5pounds (2948 grams). Barrel: 22.5 inches, rifled. Total Length: 40.3 inches Propulsion: 12 gram CO2 x2 or 88 gram CO2 x1 Action: Bolt action repeater. Ammunition Type: .177 caliber pellets. Ammunition Capacity: 9 round rotary magazine x2. FPS: 490.
Trigger Pull: The trigger pull on Umarex Fusion 2 CO2 .177 Caliber Bolt Action Pellet Rifle feels pretty good, it is fairly short and light having a claimed 3.5 pound release which is believable. You will need to obviously work the bolt for each shot that precooks the internal hammer/striker allowing for the short and light trigger.
Accuracy: I have not performed my Field Test Shooting Video for the Umarex Fusion 2 CO2 .177 Caliber Bolt Action Pellet Rifle so stay posted for that. Umarex has claimed a velocity of around 490 FPS for the Canada version I will be testing, the US version has a claimed velocity of up to 700 for those in the US purchasing this Rifle. I am sure the included 4x32 optical scope once setup will help in the accuracy department when I test this CO2 Air Rifle out on a paper target setup 30 feet down range.
Build Quality: The Umarex Fusion 2 CO2 .177 Caliber Bolt Action Pellet Rifle is a fairly low cost target pellet Rifle when you consider it comes with a decent optical scope along with two 9 round magazines but even so the build quality seems very solid coming in at 6.5 pounds. The stock is plastic of course but there is lots of metal where you want it to be as in the bolt, trigger, safety and most other mechanical parts.
Realism: The Umarex Fusion 2 CO2 .177 Caliber Bolt Action Pellet Rifle is not a replace of any gun I know of but does sport a very modern ergonomic look with its pistol grip and molded full stock. I like the built in picatinny rail which even though it does not offer any type of open sight configuration will allow for a variety of scope mounting options for near or far shooting.
Pros:
Low cost for a full featured Air Rifle with included scope.
Nice ergonomic modern looking design.
Ability to use either 12 gram or 88 gram CO2 cartridges.
Comes with 4x32 optical scope and all mounting hardware needed.
Come with two 9 round rotary magazines.
May be very quiet if the SilencAir technology is not disabled here in Canada?
Single action 3.5 pound trigger fells good.
Safety is large and easy to use.
M-LOK slots for mounting additional hardware.
Cons:
No iron sight option if you would prefer that.
Limited to under 500 fps (Canada version).
Not sure about the functionality of the SilencAir technology in Canada?
Comments: I am looking forward to performing my Indoor Field Test Shooting Video for the Umarex Fusion 2 CO2 .177 Caliber Bolt Action Pellet Rifle to see if it performs as good as it looks. I’ll probably use the duel 12 gram configuration for this test since I don’t plan on shooting 300 rounds with it for my testing. We should also find out if the SilencAir technology has been disabled or not with my Canada version but even so, a 500 fps Air Refile is not going to be all that loud either way at the end of the day. There are not a lot of Bolt Action multi shot pellet Air Rifles out there especially in this price range so I am really hoping it hits a home run when I test it so stay posted for that video…
My Vimeo Videos for the Umarex Fusion 2 CO2 .177 Caliber Bolt Action Pellet Rifle:
In this Preview Unboxing Video I do an Unboxing and take a quick look at three Bolt Action Rifles, two spring powered Airsoft Rifles from ASG and a dual CO2 powered Pellet Rifle from Umarex.
Type: BB Air pistol. Distributer:Umarex. Model:Smith & Wesson M&P9 M2.0. Materials: Metal and polymer build. Weight: 1.45 pounds (658 grams). Barrel: 3.6 inches, non-rifled. Total Length: 7.5 inches Propulsion: CO2 x1. Action: Semi auto blowback, single/double action. Ammunition Type: 4.5mm Steel BB's. Ammunition Capacity: 18 rounds. FPS: 375.
Trigger Pull: The trigger pull on the Umarex S&W M&P 9 M2.0 Blowback CO2 BB Pistol is about medium weight and is on the longer side to allow for the internal mechanism that pushes a BB for the magazine into the breach of the gun with each pull of the trigger. This does add a bit of additional resistance especially when the magazine is full of BB’s. As the magazine empties the spring resistance becomes less and makes the friction on the trigger less noticeable. When the slide blows back this does cock the internal hammer/striker allowing for less trigger pull then if the hammer is not actuated but I would say the trigger feels more like a double action trigger than a single action trigger even though most shots will be fired in single action.
Accuracy: I have not performed my Field Test Shooting Video for the Umarex S&W M&P 9 M2.0 Blowback CO2 BB Pistol so stay posted for that. Umarex has claimed an velocity of around 375 FPS adn this Airgun shoudl be abel to achieve that with it’s partial blowback more effect use of CO2. In terms of accuracy well I guess we will find out when I make my shooting review…
Build Quality: The Umarex S&W M&P 9 M2.0 Blowback CO2 BB Pistol build quality is fairly decent , fit and finish looks good with not too much slide wiggle and the materials used are both metal and plastic or polymer that look to be good quality.
Realism: The Umarex S&W M&P 9 M2.0 Blowback CO2 BB Pistol in terms of looking like the real steel version of its counterpart is very close for sure, would be hard to tell without further investigation. Umarex has done a great job of making this Blowback Airguns look believable by covering the CO2 screw, recessing the barrel and even working the manual safety into the right side slide catch release. In terms of operation the Umarex S&W M&P 9 M2.0 Blowback CO2 BB Pistol functions as you would expect other than it can not be easily filed striped and the blowback operation does not cycle back as much as a full blowback gun would.
Pros:
Very accurate replica of the S&W M&P 9 M2.0.
Fairly accurate weight and feel to it.
Metal and plastic parts where you find them on the real steel version, fit and finish is good.
Working trigger and manual safety and working slide catch and release.
Full size dropout metal magazine that holds BB's and CO2.
Warning instructions are discreet under the trigger guard.
Recessed barrel and hidden CO2 screw for more realistic look
Fully Smith & Wesson licensed via Umarex.
Rail for add on accessories.
White dot sights for easy target acquisition.
Comes with three sizes of interchangeable grips S/M/L.
Higher fps and more shots per CO2 than full blowback versions.
Cons:
Not full blowback but uses partial blowback.
Manual safety worked into right side slide catch release (Maybe good, maybe bad).
Sight are not adjustable.
Trigger is more like a double action trigger.
Comments: Overall the Umarex S&W M&P 9 M2.0 Blowback CO2 BB Pistol makes for a nice replica Blowback Airgun version of the S&W M&P 9 M2.0. There are some compromises with this version mainly the partial blowback operation that does make the trigger a bit heavier and longer than a true single action trigger would be, the slide does not cycle as fully as expected either and y9ou can not easily field strip this version. That said the shorter blowback action and the way the BB is pushed forward into the breach before each shot means that the Umarex S&W M&P 9 M2.0 Blowback CO2 BB Pistol will have a high FPS and will also get more shots per CO2. So you decide what may be more important to you at the end of the day? True realism or better performance?
My Vimeo Videos for the Umarex Smith & Wesson M&P9 M2.0 CO2 Blowback BB Pistol:
UPDATE: All Umarex Glock 17 Gen 4 and Glock 19 Gen 3 GBB Airsoft Pistols now ship with the Shorter Barrels!!
In this Field Test Shooting Video I test out the Umarex Glock 17 Gen 4 GBB Airsoft Pistol in the Replica Airguns Indoor Sean Airgun Shooting range. This product now comes with the longer sticking out barrel to increase the FPS for import into Canada to get it up and over the 360 FPS requirement using a .20 gram Airsoft BB. In my previous video I test out the Umarex Glock 19 Gen 3 GBB Airsoft Pistol but swapped out the longer barrel for the shorter barrel to see how much the sorter barrel reduces velocity and also if there is an impact on accuracy? Make sure to watch that video to get the scoop on the shorter barrel with both the Umarex Glock 17 dam Glock 19 GBB Airsoft Pistols
For the velocity portion of this test I placed several .25 gram Airsoft BB’s through my Chronograph and was please to get a very consistent 355 average FPS reading which is very close to the claimed 360 FPS when using .20 gram Airsoft BB’s so if I had been using a lighter BB I would have for sure seen velocity up and over the 360 FPS.
In terms of accuracy the Umarex Glock 17 Gen 4 GBB Airsoft Pistol also performed really well, maybe not as well as the short barrel Glock 19 Gen 3 I tested just last week that seemed to group just a little bit tighter and was a little bit more well vented on the target. Both the Glock 17 and Glock 19 shot a bit low but I am sure a slight hop-up tweak could rectify that. I did however manage to get around a 2 - 2.5 inch 10 shot grouping.
So in summary both the Umarex Glock 17 Gen 4 and Glock 19 Gen 3 GBB Airsoft Pistols at least for now come with the longer barrels only and so you options are to either cut down the existing barrel or buy a shorter barrel and replace it, that is unless you like the look of the long sticking out barrel ;) You will get a velocity drop of around 75 FPS with the shorter barrel installed but I would say accuracy should be about the same at the end of the day.
UPDATE: All Umarex Glock 17 Gen 4 and Glock 19 Gen 3 GBB Airsoft Pistols now ship with the Shorter Barrels!!
In this Field Test Shooting Video I test out the Umarex Glock 19 Gen 3 GBB Airsoft Pistol in the Replica Airguns Indoor Sean Airgun Shooting range. This product now comes with the longer sticking out barrel to increase the FPS for import into Canada to get it up and over the 360 FPS cut off using a .20 gram Airsoft BB. I wanted to see how much of a difference the shorter barrel would make so I will be comparing the short barrel with the long barrel to find out the FPS and accuracy differences. In the Video I only shoot the Umarex Glock 19 Gen 3 GBB Airsoft Pistol with the short barrel but in my next video I Shot the Umarex Glock 17 Gen 4 GBB Airsoft Pistol with its included long barrel for comparison.
For the velocity portion of this test I placed 5 .25 gram Airsoft BB’s through my Chronograph and was please to get a very consistent 276 average FPS reading with the slowest shot hitting 274 FPS and the fastest shot hitting 278 FPS so really close. Keep in mind I was using .25 gram Airsoft BB’s rather than .20 gram Airsoft BB’s so I would imagine the Umarex Glock 19 Gen 3 GBB Airsoft Pistol even using the shorter barrel should hit closer to 300 FPS with the lighter Airsoft BB’s.
In terms of accuracy the Umarex Glock 19 Gen 3 GBB Airsoft Pistol also performed really well, I did not make any adjustments to the gun after installing the shorter barrel not even to the hopup. I was pleased to see a fairly well centered 10 shot grouping mostly within a 2 inch grouping with perhaps one flyer extending that group to about 2.5 inches. All shots where well centered left to right but just a light bit under the target, a quick hopup adjustment should rectify that.
My next Vimeo Video will be focusing on the Umarex Glock 17 Gen 4 GBB Airsoft Pistol with its included long barrel to see what kind of velocity gains we get for it and if the longer barrel helps with accuracy at all so look for that video early next week!
UPDATE: All Umarex Glock 17 Gen 4 and Glock 19 Gen 3 GBB Airsoft Pistols now ship with the Shorter Barrels!!
Type: Blowback GBB Airsoft Pistols. Manufacturer: Distributed by Umarex. Model:Glock 17 Gen 4 & Glock 19 Gen 3. Materials: Metal & Polymer. Weight: 1.66 Pounds (642 grams) / 1.64 Pounds (634 grams). Barrel: Smooth bore 10.8 inch barrels. Propulsion: Green Gas or Propane. Action: Semi auto blowback, single action only trigger. Ammunition Type: 6mm plastic Airsoft BB's. Ammunition Capacity: 22 / 19 round drop out full size metal magazines. FPS: Claimed 410 with .20 gram Airsoft BB’s.
Trigger Pull: The trigger pull on the Umarex Glock 17 Gen 4 and Glock 19 Gen 3 GBB Airsoft Pistols is fairly short with only a little bit of take up, the release is light and crips. The blowback action resets the internal Hammer / Striker with each shot for that true single action trigger and it’s also nice that the trigger does have a working trigger safety like the real steel versions.
Accuracy: At this point I have not shot either of the long barrel Umarex Glock 17 Gen 4 and Glock 19 Gen 3 GBB Airsoft Pistols so I can only quote what Umarex is saying in terms of FPS which is around 410 using Green Gas or Propane. These longer barreled versions should shoot fairly hot compared to the much shorter barreled versions and since i do have a short barrel Glock 17 Gen 4 I may also compare it at the same time to see what the actual barrel length does in terms of fps velocity. Of course my Field test Shooting video will also focus on accuracy add see what can be accomplished shooting a 10 shot grouping at 30 feet down range.
Build Quality: TheUmarex Glock 17 Gen 4 and Glock 19 Gen 3 GBB Airsoft Pistols seems well made overall. It does seem a little bit underweight but still feels solid enough in the hand, Glocks are not known for being all that hefty. The Slide is metal but has a bit of an unusual finish that makes it look a lot like the plastic frame rather than a more shiny metal look. All the parts seem to fit nicely, maybe even a bit snug at first as I noticed the side had a bit of friction to it but seems to be working in nicely now.
Realism: The Umarex Glock 17 Gen 4 and Glock 19 Gen 3 GBB Airsoft Pistols look the part of these Glocks all day long. Other then the slightly lighter weight it would be hard to tell off hand until you remove the magazine and take a closer look. All the parts work as you would expect them to, similar to the real steel version and you can even fully field strip the them which makes getting to and adjusting the hop-up easy enough to do. Available From: The Replica Airguns Store.
Pros:
Decent weight and feel to them, build quality seems good.
Really nice looking replicas of the original Glock 17 Gen 4 / Glock 19 Gen 3.
Fully Glock licensed via Umarex.
Easy to see white dot sights front and back with rear sight adjustable for windage.
Recessed barrel for added realism when cut down.
Accessory rail for adding a laser or tactical light.
Full size drop out metal magazines that holds the Green Gas and 6mm Airsoft BB’s.
Warning instruction are nice and discreet under trigger guard.
Nice light SAO trigger as the blowback action pre-cocks the internal hammer/striker.
Working trigger safeties.
No red tips and more realistic outer barrel size.
Cons:
Only comes with the longer barrel so you need to either cut it down or replace it with a shorter barrel.
No way to put a mock suppressor on it to keep extended barrel.
Comments:
Getting the Umarex BB versions of the Glock 17 and Glock 19 has for sure been a bit easier since fps velocity is not a factor. So it’s great that we at least have a way to import these two Umarex Glock GBB Airsoft Pistols into Canada! Yes some home modifications may be required to cut down the inner barrel as the long extended barrels are certainly not practical for every day shooting. That said with the extended long barrels I did get out and shoot a few rounds through them and the added barrel length really does allow for a much faster velocity Airsoft BB making these Umarex GBB Airsoft Glocks more like snipper pistols :)
If you have been watching my Video Reviews you may have picked up on the fact that I am a bit of a 1911 fan! Perhaps it goes back to my Magnum PI day, I am sure I have watched every episode a bunch of times as a kid and growing up, Tom Selleck’s side arm of choice was the classic Colt 1911 A1 and I guess it brushed off on me. I just like the look and feel of the classic 1911!
There have been a number of BB firing Airguns that have come out over the years so I thought I would go over a few of my favorite versions and talk a little bit about their history and cover a few different version most actually made by KWC based off of their original full blowback CO2 1911.
Here are links to my YouTube Video Reviews for the CO2 BB Airguns I show and discuss in this video:
Type: Blowback BB Pistol Manufacturer: Crosman Model:Night Stalker Materials: Metal and Plastic. Weight: 1.6 pounds (726 grams). Barrel: 4.75 inches rifled. Length: 7 inches. Propulsion: CO2 x 1 Action: Blowback , single action only trigger. Ammunition Type: 4.5mm Steel BB's. Ammunition Capacity: 20 Rounds. FPS: 420.
Trigger Pull: The trigger pull on the Crosman Night Stalker CO2 Blowback BB Pistol with Laser is single action only and therefor is fairly light in general. It does have a longer take-up then most single action only triggers but has a predictable and crisp release to it. You will need to rack the slide for the first shot in order to pre-cock the hammer but then the blowback action takes over this process for you.
Accuracy: I actually have performed my Field Test Shooting Video for the Crosman Night Stalker CO2 Blowback BB Pistol with Laser and in terms of power I did manage to get really close to the claimed 420 fps with my results being 405 in medium warm temperatures. Accuracy was not as goods as I was hoping for with a 10 shot grouping of around 3 inches. It would have been nice to get closer to a 2 inch grouping. The laser will need to be adjusted out of the box to line up the aim point with the shot placement.
Build Quality: The build quality for the Crosman Night Stalker CO2 Blowback BB Pistol with Laser is good overall, the Airgun feels really solid in the hand and even though it is not super heavy it is also not a large Airguns so it feels solid enough being mostly made out of metal. You will find it has a metal slide, frame, trigger, hammer and also the stick magazine giving the Crosman Night Stalker CO2 Blowback BB Pistol with Laser a nice balance to it. Fit and finish is also good with only a little bit of slide wiggle.
Realism: The Crosman Night Stalker CO2 Blowback BB Pistol with Laser is not an exact replace of any real steel gun in production that I know of but it does kind of look like a larger Walther PPK that is a bit more squared off and modernized. I would say closer in size to a Makarov which also has some PPK looking traits to it. The blowback operation does also help in terms of realism but it is very snappy and quick, almost too fast for the eye to see.
Pros:
Pretty much all metal gun feels good in the hand.
Snappy blowback operation.
Decent single action trigger (has a bit of take-up but fairly light release).
Comes with integrated laser which is easy to sight in using the supplied Allen key.
Stick mag is all metal with good weight to it.
Laser does not impede the rail so you can still add on accessories..
White dot sight on the back sight.
Cons:
Sights are not adjustable but laser is.
Blowback feel is very slight.
CO2 tab is slightly exposed.
Stick mag rather than full size magazine.
Comments: I do really like the look and feel of the Crosman Night Stalker CO2 Blowback BB Pistol with Laser, it has a nice size and weight to it and balances nicely in the hand. The integrated laser keeps this airguns streamline and even allows for the addition of a tac light or other rail accessory to be added. Blowbacks action is slight but does allow for single action only trigger which makes it lighter than a double action trigger and more responsive for action shooting. The Velocity is up and into the 400 fps range which is good for a blowback CO2 BB Pistol, I would just like to see the accuracy tighten up a little bit but perhaps my test results could be improved with more trigger time using the Crosman Night Stalker CO2 Blowback BB Pistol.
Type: Pellet & BB Revolver Manufacturer: Crosman Model:Vigilante Materials: Metal and Plastic. Weight: 2 pounds (908 grams). Barrel: 6 inches rifled. Length: 11.36 inches. Propulsion: CO2 x 1 Action: Revolve , single and double action trigger. Ammunition Type: 4.5mm Steel BB's / .177 caliber Pellets. Ammunition Capacity: 6-BB / 10-Pellet round rotary magazines. FPS: 465-BB’s / 435-Pellets.
Trigger Pull: The trigger pull on the Crosman Vigilante CO2 Pellet and BB Revolver is rather nice in single action with virtually zero take-up and it has a not too light weight with a predictable feel to it. In double action it does get much longer and heavier but still very usable. If you have larger thicker finger then you may want to start off in single action as the finger opening is a bit tight.
Accuracy: I have not specifically tested out the Crosman Vigilante CO2 Pellet and BB Revolver so far but I would be very surprised if it was any different than the standard Crosman 357 I tested back in 2012. Other than the shape of the outer barrel, both of these guns are virtually the same including the frame and the 6 inch barrels. Back in 2012 when I tested out the Crosman 357 I averaged 402 fps using 6.9 grain pellets and was able to get a 1 inch multi-shot grouping at 30 feet away from my paper target. Not sure if this was the entire 10 round mag or not? I will be making an update Field Test Shooting Video so we will see if I can replicate these results with the Crosman Vigilante CO2 Pellet and BB Revolver.
Build Quality: The Crosman Vigilante CO2 Pellet and BB Revolver is a fairly basic pistol that incorporates a plastic outer barrel and inner steel barrel, the grips are also plastic as expected and so are the magazines and sights. Most everything else is metal including the receiver, trigger and hammer. This line of Crosman 357 pistols has been around for decades so you can expect hours of fun and reliable shooting with it.
Realism: There are for sure a lot more realistic looking Revolvers out there with swing out cylinders that except shells just like their real steel counterparts but where the Crosman Vigilante CO2 Pellet and BB Revolver shines is in performance. You will get more shots per CO2, higher fps and better accuracy with the Crosman Vigilante CO2 Pellet and BB Revolver over other more realistic Revolvers on the market.
Pros:
Inexpensive Pellet revolver with a proven track record that goes back decades.
Good usage of metal parts where you need them most. (Metal trigger, hammer, frame, barrel, CO2 Tab screw
Single and double action trigger for action and more focused shooting.
Excellent accuracy and good power with a reasonable amount of shots per CO2.
Fully adjustable rear sight.
Can mount a bunch of accessories on the picatinny barrel top and bottom rails.
CO2 and CO2 tab are nicely hidden and use all metal.
Comes with both a Pellet and BB magazine.
Cons:
Outer barrel is plastic but very solid. Metal would have added a bit more weight and perhaps better balance?
Grips and trigger pull length may be a bit long for smaller handed people when shooting in double action.
Not your most realistic revolver in terms of replicas out there but I would say more usable than most.
No white dots on the sights.
The Crosman Vigilante CO2 Pellet and BB Revolver is basically a reskinned Crosman 357 at the end of the day but I have to say it is my favorite looking Crosman 357 out there with its aggressive barrel design. And the added bonus are the top and bottom Picatinny rails which make for mounting accessories like Red Dots, Lasers and Tac Lights super easy! if you’re looking for function over realism at a price point that is more than fair then pick yourself up one of the Crosman Vigilante’s from our Replica Airguns Store!
Type: GBB Airsoft Pistol. Manufacturer: WE Airsoft Model:1039 M2 Materials: Mostly all metal build. Weight: 2.43 pounds (1100 grams). Barrel: 4.53 inches, non-rifled. Length: 8.5 inches. Propulsion: Green Gas Action: Semi & full Auto, single and double action trigger. Ammunition Type: 6mm Plastic Airsoft BB's. Ammunition Capacity: 26 round full size dropout metal magazine. FPS: 366+.
Trigger Pull: The trigger pull on the WE M92 GBB Full Auto Airsoft Pistol is good in both single and double action. Double action as expected has the longer heavier pull but is still smooth and fairly light with a predictable release. Single action shooting has a much shorter trigger pull with a bit of take-up and an even lighter release than in double action shooting mode.
Accuracy: This is one of those times I actually performed my Field Test Portion of my Review first so I do have some feedback in terms of the accuracy and velocity for the WE M92 GBB Full Auto Airsoft Pistol. WE claims an fps of around 366+ using the extended barrel that comes with it so this is how I tested it. I did use .26 gram airsoft BB’s so the fps was a bit lower but I did get close to 320 fps, So you should expect around a 20% increase in FPS using .20 gram Airsoft BB’s, so closer to 360-380 fps. In terms of accuracy I did notice that the WE M92 GBB Full Auto Airsoft Pistol shot rather low for me, as much as 8 inches at 30 feet out, perhaps adjustment get hop-up will fix that, at longer ranges it should… That said I found I was able to get around a 1-5.2 inch 10 round grouping at 30 feet out. In terms of full auto, all I can say is don’t expect to hit very much you point at as the gun really likes to rock around!
Build Quality: The WE M92 GBB Full Auto Airsoft Pistol is a really gorgeous looking pistol and has one of my favorite looking finishes in that stainless steel look. You will find it has an overall solid build quality, it is virtually all metal with only the grips and some internal parts like the gas chamber and nozzle being plastic. There is almost zero slide wiggle and all in all this Airsoft pistol performed great for me with no mechanical problems.
Realism: As is with most Full Blowback Airsoft Pistols they are built to look and act the part of their real steel counterparts and the WE M92 GBB Full Auto Airsoft Pistol is no exception! All mechanical parts work as intended and you can easily field strip the WE M92 GBB Full Auto Airsoft Pistol to swap out the internal barrel and adjust the hop-up. I like the fact that WE Airsoft color matched the magazine rather than simply shipping it with the black magazine as I have found some other companies do.
Pros:
All metal pistol with good weight to it.
Crisp firm full blowback operation.
Excellent fit and finish.
No markings on the metal parts at all, just the WE branding on the grips.
Color matching magazine.
Gun will accept real Beretta M9 grips.
Semi and full auto selector safety switch.
White dot sights front and back.
Good fps, right around the claimed 366 using .20 gram Airsoft BB’s.
Very believable working replica of the real steel Beretta M9 Pistol.
Fully field strip-able.
Comes with extension barrel and replaceable inner barrel if not going to use extension.
Cons:
No marking on the gun if that is important to you?
Shot rather low in my testing but hop-up and barrel change may fix it.
Almost unusable in Full Auto mode.
The WE M92 GBB Full Auto Airsoft Pistol is one of the nicer looking Airsoft Beretta M9 pistols on the market and is comparable in quality to other higher end brands like KWA and KJWorks. The price point is also in line with what you are getting. I really like the Stainless - Silver - Chrome finish or what ever you want to call it… One thing I was not able to determine 100% is if this version is in fact the Gen 2 version but I do believe it is given that it has the black gas tube in it. We just don’t have it advertised as such. If you’re in the market for a Beretta style M9 Pistol then consider the WE M92 GBB Full Auto Airsoft Pistol as a solid choice.
Today I decided to get outside since the weather was nice and make my Field Test Shooting Video for the ASG TAC-6 CO2 Airsoft Rifle (actually outside in the filed!) After all the ASG TAC-6 CO2 Airsoft Rifle is a sniper rifle and so I wanted to test it out at longer ranges than my 30 foot indoor shooting range can allow for. So I setup two paper targets at around 40 feet and 80 feet out, the actually distance may have been longer than that?
Starting off my Field Test Review I placed five .25 gram plastic Airsoft BB’s through my Chronograph and averaged 446 fps which is 6 fps faster than the claimed 440 fps from ASG. And that was with .25 gram Airsoft BB’s so if I was using lighter .20 gram BB’s I would expect velocity closer to around 500fps so don’t be shooting anyone with this Airsoft Rifle at close ranges!
Next I proceeded with my accuracy test placing 5 rounds on the target setup around 40 feet downrange. I managed to get all 5 rounds within about 2 inches of each other, not bad since this is a good 10 feet more than I usually test my Airsoft Rifles at. With the remaining 10 rounds in my magazines I was hoping to get at least a couple shots on my paper target setup a good 80 feet away but did not have much luck, I even reloaded the 15 round stick magazine 2 more times and gave it a go but again with no success! The Airsoft BB’s seemed to want to angle off in all direction usually up and to the right or left right before the 80 foot target, perhaps I would have had much better luck at 60 feet?
All I can surmise from this higher range Field Test is that the ASG TAC-6 CO2 Airsoft Rifle is not really a long range Airsoft gun at least with the .25 gram Airsoft BB’s I was using, maybe heavier Airsoft BB’s would settle down a bit more? I can say at ranges up to 40 feet the ASG TAC-6 CO2 Airsoft Rifle did perform just fine so keep that in mind when looking into buying one of these as smoking cans at 30-40 feet will be no problem and make for some fun times in the back yard or even basement makeshift gun range.
Type: Airsoft Rifle. Manufacturer: ASG. Model:TAC-6. Materials: Plastic with some internal metal parts. Weight: 3.5 pounds (1588 grams). Barrel: 12 inches, metal non-rifled. Length: 36 inches. Propulsion: 12 gram CO2 x 1. Action: Semi auto, double action only. Ammunition Type: 6mm BB's. Ammunition Capacity: 15 round metal stick magazine. FPS: 440.
Trigger Pull: The double action only type trigger pull on the ASG TAC-6 CO2 Airsoft Rifle is not too heavy but it is rather long so really quick rapped fire shooting will require some finger work. The trigger reset is right at the begging of the pull so you need to make sure you allow the trigger full range of motion or you may miss the odd shot.
Accuracy: I haven't done my Field Test Shooting video just yet for the ASG TAC-6 CO2 Airsoft Rifle but will shortly so stay posted for that video. ASG claimed the fps to be right around 440 and I am assuming with .20 gram Airsoft BB’s, I will most likely busing .25 gram Airsfto BB’s for my testing so I am hoping for around 400 fps or so. With the fiber optic front sight and fully adjustable rear peep sight I shoudl be able to get some decent rounds on target downrange and hopefully get a nice grouping.
Build Quality: The ASG TAC-6 CO2 Airsoft Rifle is mostly plastic but feels pretty good in the hand with decent fit and finish. There are some metal internal part along with the outer barrel and top rail but for the most part the ASG TAC-6 CO2 Airsoft Rifle is all plastic including the trigger and front and rear sights.
Realism: The ASG TAC-6 CO2 Airsoft Rifle is not a replica of any modern rifle that I know of but it does look a bit like a Beretta CX4 Storm especially the back half of it. The flash hider and top and bottom raise add to the realism. Available From: The Replica Airguns Store.
Pros:
Very customizable with rails top and bottom.
Comes with a rather nice Bipod that can be used with other rifles.
Front and back removable Iron sights are very usable, fiber optic in front, peep in back.
Safety switch is in a great location for right handed shooters.
Canada version comes with black flash hider.
Mostly plastic but solid construction.
Rubber Butt Pad is nice and thick.
Removable barrel to reduce size for easier transportation.
Also come in 4.5mm Steel BB version.
Optional Integrated laser can be added.
Cons:
DOA Trigger pull is a bit long which will slow down rapid fire shooting a bit.
Mostly Plastic Polymer build.
Why not a longer inner barrel for possible more fps?
CO2 is in the Pistol grip and not the magazine so may not be great for on field battles.
Comments: This may not be the most exciting Airsoft Rifle I have reviewed, it does look kind of cool and the price is right compared to other Airsoft Rifles. Who is it really for? I would say someone looking for an Air Rifle for plinking in the backyard or basement that perhaps want's a little bit more safety in terms of using plastic BB’s rather than Steel BB’s. Sure you can use the ASG TAC-6 CO2 Airsoft Rifle for Airsoft wars but most people want something a bit more realistic in terms of looks and function. Because the ASG TAC-6 CO2 Airsoft Rifle does have built-in Popup it shoudl be able to reach out to longer ranges so we will have to see if it can perform decent at longer ranges when I do my Field test Shooting Video.
My YouTube Table Top Review Video for the ASG TAC-6 CO2 Airsoft Rifle:
I will say right off the bat this Field Test Shooting Video for the Air Venturi 3000 PSI Aluminum HPA Tank with Stock and Adapter did not go as well as I would have wanted it to! The HPA tank itself worked really well but I believe the adapter was faulty as it was destroying the seals on my tank and not regulating very well.
I still wanted to publish this video regardless as not all reviews go as planned, some fail horribly but I would rather be honest and transparent about it rather than have you believe every product is a perfect.
There will always be problems even with really great products there can be defects. I plan to get a new adaptor and try this Field Test Review Video again but for now you can have some fun watching me at least have some success using the Air Venturi 3000 PSI Aluminum HPA Tank with Stock on my Rap4 Rap5 MP5.
You can also watch my Table Top Review Video for more details and info on this product!
I will also be following up my Table Top video with a Field Test Shooting Video to see what possible advantages and disadvantages the Air Venturi 3000 PSI with Stock & Adapter Aluminum Tank has in a real world test of its performance, hopefully all advantages!
Pros:
Compact and is the perfect size to use as a rear buttstock for various 88 Gram and or HPA rifles.
Smaller tank means if you are using a foot pump it won’t take all day to fill up :)
Comes with adapter so can be used with regular HPA and 88 Gram CO2 systems.
Regulated to 1100 psi so should perform better in terms of max velocity and consistency compared to CO2 which is around max 800-900 psi with velocity being effected by cool down.
Not effected by colder temperatures compared to CO2.
Once you have this tank the cost is virtually nothing to shoot compared to expensive 88 Gram CO2 cartages. You just need to buy your pellets or BB’s.
Cons:
Still takes a while to pump up using a foot pump system.
Higher initial cost ($195) than simply buying 88 gram CO2 cartages when you need them.
Will need access to a pump or compressor to use it.
Doesn’t look as good as the supplied buttstock at least with the Sig Sauer MCX and MPX.
Comments:
I guess the question is who is this for? If you are a casual shooter that perhaps owns the Sig MPX or MCX or even another 88 Gram CO2 Air Rifle that the Air Venturi 3000 PSI with Stock & Adapter Aluminum Tank would work with then this may be a bit expensive especially if you don’t have a way to pressurizer the tank at home. On the other hand if you already have a foot pump or air compressor or easy access to one and maybe you have other HPA or CO2 based airguns this tank will work with then it’s kind a no brainer to get it. Maybe you juts want a system that gives you maximum and consistent velocity no matter how cold it is outside. All good reasons to get one in my books.
In this Update Preview Unboxing Video I take a look at 5 products that came across my table and that I have not reviewed so far on the Replica Airguns YouTube channel.
First I show off an HPA tank from Air Venturi that works perfectly for the Sig Sauer MPX and MCX Pellet Rifles allowing for more consistent fps and I would image a higher overall fps? We will find out when I test it out in the replica Airguns Indoor Sea Can Airgun Range.
13 Oz Aluminum
10 Inches Long
2 Inches Diameter
Integrated Pressure Gauge
Includes Buttstock
CO2 Adaptor Included
3000 PSI Fill
1100 PSI Regulated
Next I take a look at the KJWorks M9A1 GBB Airsoft Pistol, I hover revived the CO2 version before but this version comes with the Gas magazine rather than the CO2 mag for those that prefer gas operated Blowback Airsoft Pistols. Because of the slightly lower FPS the Gas version comes with a barrel extension to make it Canada import friendly.
6mm Airsoft BB’s
Green Gas / Propane
370 fps
25 Round Magazine
2 Pounds
Probably one of the most interesting product I look at in this video at least for me is the EMG JW3 Combat Master GBB Airsoft Pistol. This Airsoft pistol is mainly aluminum with some polymer based off of the 2011 STI and was featured in the 2019 John Wick 3 Film. I’m really looking forward to testing this one out in the Sea Can Replica Airguns Airgun Range!
6mm Airsoft BB’s
Green Gas / Propane
9.4 Inches
366 fps
28 Round Magazine
2.4 Pounds
Moving along to another Air Pistol I finally get my hands on the Crosman P1 which is really just a KWC PT92 4.5mm Blowback CO2 BB Pistol but with Crosman Branding and an included laser. Since I have never shot a PT92 BB Pistol with a laser I will probably make a Field Test Shooting Video to see how well it performs.
4.5 mm Steel BB’s
CO2 x 1
4.2 Inch Barrel
330 fps
19 Round Magazine
2.4 Pounds
Comes with Laser Sight
Last up I take a look at the ASG TAC-6 which is pretty much the exact same ASG TAC-4.5 CO2 Air Rifle I tested a while back but in this case the 6 refers to it being a 6mm Airsoft Rifle rather than a 4.5mm Steel BB Riffle. I am not sure I will do a full Table Top Video since these guns are virtually identical but just in different Ammo types but I hope to get outside and see how well it performs shooting at a bit more distance than the 30 foot indoor range I usually test my Airgun in.
I have been wanting to test out the Crosman Full Auto Quick Reload Magazine for a while now and finally got around to it. The weather was cooperating with me so I went outside for this one and setup a bunch of cameras to make the many many magazine reloads a bit more interesting for my viewers.
The Crosman Full Auto Quick Reload Magazine has a hopper that is said to hold around 300 4.5mm Steel BB’s which I can attest it does in fact hold at least 300 BB’s. The Crosman Full Auto Quick Reload Magazine like their regular Crosman Full Auto Magazines holds two 12 gram CO2 Cartridges, so the question is, will I be able to get through most of the 300 BB’s without reloading the CO2?
Watch my struggle a bit to figure out the exactly how to properly use the Crosman Full Auto Quick Reload Magazine and then quickly eat through 300 or so BB’s blasting pop cans down range!
