Entries in Revolver,Real Gun

ROHM Little Joe Belt Buckle 6mm Flobert Blank Gun Review

2 Comments

Type: Blank revolver.

Manufacturer:RÖHM.

Model:Little Joe Belt Buckle.

Materials: Mostly metal with plastic grips.

Weight: .3 pounds (134 grams).

Barrel: Front firing.

Propulsion: Gun powder.

Action: Revolver, single action only

Ammunition Type: .22 caliber crimped blanks (6mm Flobert).

Ammunition Capacity: 5 rounds.

FPS: NA.

Trigger Pull: The trigger pull for the Little Joe blank revolver is single action only, you must pre-cock the hammer first to rotate advance the cylinder and ready the hammer to fire. I very short medium weight trigger pull with virtually no take-up is required to fire this tiny revolver at that point.

Accuracy: NA.

Build Quality: Even though in general blank/signal guns do utilize scaled down metals like zinc alloy (not high pressure gun steel), the ROHM line of blank pistols are made very well and many of the internal mechanical parts, pins and screws are solid steel. The fit and finish is excellent and when I tested my none belt buckle Little Joe it shot flawlessly for me. Don't expect much recoil from the small acorn .22 rounds.

Realism: The ROHM Little Joe Belt Buckle 6mm Flobert Blank Gun is not a true replica of any real steel revolver in production but it does look a bit like the North America Arms NAA22s Mini-Revolver chambered in .22 short. North America Arms even has a belt buckle version of their own!

ROHM Guns Available in the: Replica Airguns Store

Pros:

  • It’s a blank gun that fits into a belt buckle!

  • German made Quality.

  • Like the satin or stainless finish.

  • Pretty much all metal gun with some steel in a few areas.

  • Front firing revolver that will fir a flare adaptor.

  • Uses inexpensive 22 Acorn blanks (6mm Flobert)

  • Kind of rare in Canada, cool if you own one :)

Cons:

  • Hard to get the Belt Buckle version here in Canada.

  • Not sure about legalities actually wearing the belt buckle in Canada?

Comments:

I already thought the standard ROHM Little Joe Blank firing mini revolver was a really cool gun, to actually find one that fits into a belt buckle is even cooler! I wish we had these for sale in our Canada Replica Airguns Store but it's probably best we don't since I know some people will decide to wear theirs which is bad news since it's only a matter of time before a call is made and a lot of explaining is in order... The good news is we do sell the none belt buckle version of the Little Joe .22 Caliber (6mm Flobert) Mini Revolver in our Canada Replica Airgun Store along with many other ROHM German quality blank pistols so check them out for sure!

My Vimeo Table Top Review for the ROHM Little Joe Belt Buckle 6mm Flobert Blank Revolver:

 
Categories: .22 cal, Blank Gun, Comparison, Pistol, Review, Revolver, YouTube Video Tags: Little Joe, ROHM

2013 Blued Baikal Makarov MP-654K CO2 BB Pistol Table Top Review

1 Comment

Type: BB air pistol.

Manufacturer:Baikal.

Model: MP-654K.

Materials: Weapons grade steel slide, frame and most parts.

Weight: 1.7 pounds.

Barrel: 3.8 inches, metal-rifled.

Propulsion: CO2 x 1.

Action: Semi auto, double and single action.

Ammunition Type: Steel/Lead BB's 4.5mm.

Ammunition Capacity: 13 rounds.

FPS: 380.

Trigger Pull: The trigger pull on the 2013 Blued Baikal Makarov MP-654K CO2 BB Pistol is good in single action mode (When cocked), when shooting in double action mode it is a bit heavy but it seems like over time the gun is working its self in a bit as the metal is hard and as with many Russian made guns, they need some break in period. The trigger springs are heavy so don't expect light trigger pulls.

Accuracy: The accuracy and true feet per second performance will be tested when I do my future Field Test Shooting review.

Build Quality: Excellent, the Baikal Makarov MP-654K CO2 BB Pistol is made side by side using the same machine sand same materials as the original Makarov PM (9x18) firearm that it is Replica of. There simply is not another airgun made to this quality level or that is as accurate a replica of it's real steel version.

Realism: You simply can not get any closer to how close this gun resembles the original Makarov PM (9x18). You can even field strip this gun exactly like the original. The only acceptation is when it come time to fire the BB gun version, The Baikal MP-654K is not designed to have blowback operation which is understandable as it would be impossible to fabricate this gun so close to the original and still give it blowback operation.

Pros:

  • All Steel construction

  • Made side by side in the factory to the real steel version with same build quality and on same machines.

  • The closest BB gun to a real gun you can get in terms replicating the parts and being made out of the same materials as the real version.

  • Can filed strip like the real version.

  • New 2013 version has recessed barrel.

  • New 2013 version has the flush CO2 screw.

  • New 2013 version is the PM style with narrower handle and PM grips.

  • Can field strip like the real version.

  • Shoots in single and double action.

  • Safety works as a de-cocker.

  • Made in Russia!

Cons:

  • Expensive compared to other airguns.

  • No blowback operation.

  • Only a 13 round magazine.

  • Gun requires some breaking time.

Comments:

The new 2013 Blued Baikal MP-654K PM Styled BB Air pistol is one of those must have airguns if you are a collector, sure the price is a lot more than most airgun replicas out there but the 2013 Blued Baikal MP-654K is built like no other airgun. Rather than creating a replica gun around existing airgun parts, Baikal takes a different approach and reworks a real Makarov backwards so it is made to shoot steel BB's using CO2 rather than 9mm rounds. You could say it is a real Makarov but chambered to shoot steel BB's and use CO2. These guns are rarely available in Canada since they often get stuck in customs because they are so realistic. I was actually very surprised when we located a secure that had some that they where willing to give up!

My Vimeo Video Review for the 2013 Blued Baikal Makarov MP-654K CO2 BB Pistol:

 
Categories: 4.5mm / .177 cal, BB, CO2, Pistol, Real Gun, Review, Semi Auto, YouTube Video Tags: Baikal, MP-654K, Makarov

ASG Products Back in Stock In Canada Store

No Comments

Some of you have been waiting on back orders and to also make new orders of ASG products, we just received an ASG order so many ASG items are now back in stock! Any back orders will be taken care of first and then new orders will be processed, as always, stock is limited especially on certain items so act fast!

Categories: 4.5mm / .177 cal, 6mm, AEG, Airsoft, BB, Blowback, CO2, Full Auto, Pellet, Pistol, Replica Airguns News, Revolver, Rifle, Semi Auto, Spring Piston Tags: ASG

Baikal Makarov - Gletcher APS - EKOL ES 66 CO2 BB Pistol Update Video

7 Comments

More guns to show off! Good for you and me! In this update video I show you some very interesting guns indeed! As many of you are aware, the Baikal Makarov MP-654K CO2 4.5mm Steel BB pistol has been really hard to find new here in Canada, making the price of used ones escalate up into the $700+ price range for one in as new condition. Well for those looking to buy a Baikal Makarov MP-654K we have located some and have them for sale now in our Canada Replica Airguns store (Very limited supply). These are the 2013 PM new design models with the narrow grips and mags, they also have the recessed barrels and cut out extractor. We sell them in the blued version only.

Another CO2 BB pistol that has been out of stock for some time is the EKOL ES series. I reviewed the ES 55 CO2 BB Pistol a while back but until now have not been able to show off the ES 66 Series which is more browning high power looking in design. The good news is we have both the ES 55 and ES 66 CO2 4.5mm Steel BB Pistol in stock in our Canada Store. These guns are mostly metal with full size drop out metal magazines that hold the CO2 and BB's, they also shoot in both single and double action and have pretty decent power! We are now selling both the ES 55 and ES 66 series of guns in our Online Canada Store.

I've looked at several Gletcher Airguns over the last little while and finally got my hands on the Gletcher APS Blowback CO2 BB Pistol which is a replica of the Russian Stechkin Soviet Military sidearm introduced back in the 50's. It's kind of a bigger brother version of the Makarov, i was surprised at how large it actually was when i got my hands on it! The real steel version had the ability to shoot in both semi and full-auto but my Gletcher APS 4.5mm BB replica only shoots in semi auto. Again, checkout the full line of Gletcher Products in our Canada Replica Airguns Store.

Last but not least I have a neat little 22 crimped blank pistol to show everyone. What makes it unique is the fact that it fits inside a belt buckle! We do see the ROHM Little Joe 22 caliber crimped blank pistols in our online Canada Replica Airguns Store but not this belt buckle version, kind of a one off I got form my supplier, I will be keeping it ;)  Make sure to watch my ROHM Little Joe Video Review and see all the ROHM products available in our Online Store.

 
Categories: .22 cal, 4.5mm / .177 cal, BB, Blank Gun, Blowback, CO2, Comparison, Pistol, Review, Revolver, Semi Auto, YouTube Video Tags: APS, Baikal, EKOL, ES 55, ES 66, Gletcher, Little Joe, MP-654K, Makarov, ROHM

ASG Dan Wesson 6 inch Silver & 8 inch Black Pellet Revolver Table Top Review

9 Comments

Type: Pellet air Revolvers.

Manufacturer: ASG.

Model:Dan Wesson 6 and 8 inch Pellet.

Materials: Mostly Metal Design.

Weight: 2.25 - 2.3 pounds.

Barrel: Metal rifled (6 Inch Sliver - 8 Inch Black).

Propulsion: CO2 x 1.

Action: Revolver, single and double action.

Ammunition Type: .177 caliber pellets.

Ammunition Capacity: 6 rounds.

FPS: 426+.

Trigger Pull: The ASG Dan Wesson Pellet Revolvers have predictable triggers with the single action being a bit more consistent since the take up is short, and the release is fairly light. Double action mode is very usable without a lot of extra pressure required. I found I just wanted to shoot this gun in single action mode because it felt more natural being that it is a six shooter.You also want to take your time shooting since loading the pellets into each shell and then the shells into the cylinder takes a bit of time.

Accuracy: This is yet to be determined since I have not to date had the opportunity to get outside and shoot these Pellet firing Dan Wesson's. Based on the exceptional results I got shooting my Dan Wesson Steel BB versions from 30 feet away, I should be abel to crack an inch or two 6 round grouping if my shooting is on. In terms of fps performance, ASG claims the pellet versions to shoot around the same velocity as the steel BB versions. With that in mind, this should give the Pellet shooting Dan Wesson's the advantage for raw power, since the lead pellets are heavier than steel 4.5mm BB's.

Build Quality: Like the entire Dan Wesson Revolver line from ASG, the pellet series is no exception and the fit and finish is very good. Most of the revolver is metal with the exception of the grips which are a plastic with a bit of a rubberized texture to them. The modified rifled barrels are made out of hardened steel and similarly so are portions of the newly designed pellet loading shells. Overall these are improvements to the quality of the Pellet shooting Dan Wesson Revolvers over the BB and Airsoft Dan Wessons.

Realism: The ASG Dan Wesson revolvers are as close as you can get to a real six shooter. Loading and ejecting actual shells into the cylinder makes you feel like this gun is much more then an unassuming airgun! If you want that real revolver experience than a shell loading Dan Wesson is the way to go, and the addition of a rifled barrel and lead pellets to the Pellet firing version should make the shooting experience even better.

Purchased From: The Replica Airguns Store.

Pros:

  • It's a revolver with actual shells! Gives you the feeling of a real 6 shooter.
  • Almost all metal design.
  • Lots of detail in this gun, very well made, fit and finish is very good.
  • Should have good power and good accuracy. Even better than the BB versions!
  • Adjustable rear sight for windage and elevation.
  • Barrel and shell redesign are a big improvement over the BB shooting versions.

Cons:

  • Has a plastic CO2 screw tab.
  • Loading pellets does take longer than the BB versions.
  • May use more CO2 per shot than the BB versions because of heavier ammo. 

Comments:

Since I can't comment too much on the shooting experience these Pellet Dan Wessons will offer, I can say I am impressed with how ASG did the redesign of the inner barrel and pellet loading shells. It is obvious that ASG didn't just grab some parts of the shelf and quickly modify a BB version to shoot Pellets. ASG did it right and you can see the new adapted parts are of high quality and are even an improvement over the BB versions in many ways. On paper the Pellet shooting Dan Wesson's should be more accurate especially out at further ranges than the BB shooting Dan Wesson's and the Pellet versions should also hit the target with more force since they shoot a heavier projectile at around the same fps as the 4.5mm Steel BB version.

My YouTube Video Review for these Dan Wesson Pellet shooting Revolvers:

 
Categories: 4.5mm / .177 cal, CO2, Comparison, Pellet, Pistol, Review, Revolver, Semi Auto, YouTube Video Tags: ASG, Dan Wesson Pellet

ASG Dan Wesson Pellet and Gletcher TT and P08 Update Preview Video

3 Comments

Yes! Some new guns for you, and that's always a good thing for everyone, especially me since I get to play with them! I have been waiting a while to get my hands on some of the .177 caliber pellet shooting versions of the Dan Wesson Revolvers. I was actually introduced to them nearly a year ago at the last SHOT Show back in January of 2014! That's a long wait for sure...

The Pellet version Dan Wesson's look really good, the quality of the pellet shells is top notch and even the redesigned inner rifled barrels look to be very high quality. ASG did not just do a quick part swap, they really though out how they wanted everything to fit together. I am looking forward to seeing how well they shoot and will be Field Testing them both together so we can see how the barrel lengths play an effect on power and accuracy.

Next up we have two Gletcher pistols, both are classic semi auto shooters from the past, the Gletcher TT which is a Replica of the Russian Tokarev, and the Gletcher P08 which is a Luger copy. Both pistols are blowback and shoot 4.5mm Steel BB's.

Both pistols incorporate single action only triggers, metal stick magazines and working safeties, a real steel Tokarev normally would not have a safety other than the half cock hammer, Gletcher added in a discreet switch style safety on the right side of their TT. Again, I look forward to shooting both of these blowback pistols as soon as the weather picks up!

 
Categories: 4.5mm / .177 cal, BB, Blowback, CO2, Comparison, Pellet, Pistol, Review, Revolver, Semi Auto, YouTube Video Tags: ASG, Dan Wesson Pellet, Gletcher, Luger P08, TT, Tokarev

My Airgun, Airsoft Gun and Blank Gun Collection Favorites for 2014

2 Comments

It's that time once again for an end of the year Gun Collection video. And no I will not be showing off all of my guns, to show and explain them all (Approximately 200 or so?) would simply take a really long time to make and a really long time for you to watch ;)

So like last years Gun Collection Video, I take a look at some of my favorite guns from 2014.

Here is a list of the guns featured in this Collection Video with links to their original reviews: 

Categories: 4.5mm / .177 cal, 6mm, Airsoft, BB, Blank Gun, Blowback, CO2, Comparison, Full Auto, Pellet, Pistol, Review, Revolver, Rifle, Semi Auto, YouTube Video Tags:

Range Day - Shooting All Kinds of Real Guns

1 Comment

It has been way too long since I got to go to the gun range and shoot my "big boy" guns! I say that sarcastically, sure my real steel guns are fun to shoot but it sure costs a lot of money and basically all we really do is shoot paper targets. Shooting at papper targets is fun for a while but I kind of enjoy shooting my airguns at pretty much any type of target I choose to shoot at. And of course any time I want to and for pennies per shot.

So getting back to Range Day shooting my real steel big boy guns ;) I went with a couple of buddies of mine and we shot a nice variety of guns. My Norinco NP-30 double stack 45 cal 1911, my Wyoming Arms Parker 10mm, a couple of my friends Glock 40 cals, my Norinco NP-34 P228 and Norinco Tokarev Type 54 9mm pistols, my Chiappa 1911-22 and ISSC M22 22LR pistols, a nice Sig Mosquito 22LR, my buddies S&W M&P 15-22 22LR rifle along with my ISSC MK22 SCAR 22LR rifle and my friends mighty custom Ruger Mini 14 in .223 caliber...

It was a cold day but a really fun day and it gave me a chance to really use my iPhone 6 plus camera for its slow-motion capabilities in a decent lighting situation.

Enjoy the footage of these "real guns" shooting in real time and slowed down.

Categories: .22 cal, 10mm, 9mm, Field Test, Pistol, Real Gun, Rifle, Scope, Semi Auto, YouTube Video Tags: Chiappa, ISSC M22, ISSC MK22 SCAR 22LR, Norinco, S&W M&P, Wyoming Arms Parker 10mm

Gletcher NGT Silver CO2 BB Revolver Table Top Review

12 Comments

Type: BB Revolver.

Manufacturer:Gletcher.

Model: NGT Silver (Replica of Nagant M1895 Revolver).

Materials: Metal & plastic.

Weight: 1.54 pounds (700 grams).

Barrel: 4 inches, smooth bore (Steel inner barrel).

Propulsion: 12 gram CO2.

Action: Revolver - single and double action.

Ammunition Type: 4.5mm Steel BB's.

Ammunition Capacity: 7 rounds.

FPS: 361fps (110m)

Trigger Pull: The trigger pull on the Gletcher NGT Silver CO2 BB Revolver is nice and crisp in both single and double action, there is virtually no trigger wiggle and the trigger pull is decent in double action while much longer and of course nice and light in single action as expected. You will want to pre-cock the hammer for accurate single action shooting but have the option of shooting double action for any action shooting you may want to do. Keep in mind you will have to individually reload each round.

Accuracy: I have not done any shooting so far with this Gletcher revolver due to some pretty awful weather conditions. I expect it will shoot nice since it has a fairly long sight radius and the open iron sights are conducive to precise shooting.

Build Quality: The Gletcher NGT Silver CO2 BB Revolver is really well made, you can tell by it's solid weight for a fairly small pistol, all of the mechanical parts feel smooth and responsive. Everything that would be metal on the real M1895 Revolver is metal including the solid one piece cylinder. Yes the grips are imitation wood but this is to be expected. The sliver finish looks great and I like the black contrasting parts that really highlight this gun.

Realism: I've have not had the opportunity to actually put my hands on a real steel Nagant M1895 Revolver but from the photos I have viewed online, the Gletcher NGT Silver is very accurate in terms of being a BB replica. Of course the shells fit steel BB's internally and the barrel has been downscale to shoot 4.5mm Steel BB's but other than that it is very difficult to tell it from a real Nagant M1895 Revolver. Even the barrel opening is recessed and looks true to scale for the original rounds used in this revolver and you can remove the one piece cylinder similar to the real version.

Pros:

  • Beautiful Silver finish.

  • Very solid and weighty gun.

  • Hammer and trigger actions are very crisp, virtually no wiggle. 

  • CO2 is well hidden.

  • Recessed barrel looks great.

  • 7 round cylinder instead of 6 like the other shell loading.

  • Cylinder can be removed.

  • Shoots in both signal and double action.

  • Grip is nice and small so great for shooters with small.

  • Shooting performance pros yet to be determined…

Cons:

  • Non adjustable sights. (Perhaps like original)

  • No speed loading on this one, one shell at a time, so make your shots count.

  • Shooting performance cons yet to be determined…

Comments:

The Gletcher NGT Silver CO2 BB Revolver is yet another addition of shell loading revolvers like the Dan Wesson and KWC 357 based revolvers, with the exception that the Gletcher NGT is more of a blast from the past and even though it comes in at a much more compact size, it holds an additional round! Another note worthy point is the fact that Gletcher has somehow figured out a way to reduce the CO2 release valve giving the Gletcher NGT a more true to scale frame size, I am talking about the distance between the hammer and the cylinder. This allows for a more realistic and true to dimension replica which in this classic revolver is super important.

My Vimeo Table Top Video of the Gletcher NGT Silver CO2 BB Revolver:

Gletcher NGT.jpg
 
Categories: 4.5mm / .177 cal, BB, CO2, Gas, Pistol, Review, Revolver, Semi Auto, YouTube Video Tags: Gletcher, NGT, Nagant M1895

KWC 357 2.5 Inch CO2 Airsoft Revolver Table Top Review

3 Comments

Type: Airsoft revolver.

Manufacturer:KWC.

Model:357.

Materials: Mostly metal with some plastic construction.

Weight: 2 pounds (900 grams).

Barrel: 2.25 inches, non-rifled.

Propulsion: 12 gram CO2.

Action: Revolver, single & double actions.

Ammunition Type: 6mm plastic Airsoft BB's.

Ammunition Capacity: 6 rounds.

FPS: 360+.

Trigger Pull: The trigger pull on the KWC 357 2.5 Inch CO2 Airsoft Revolver is good in both single and double action, even better than the Dan Wesson and S&W 327 TRR8 shell loading revolvers, most likely because the spring tension that pushes the inner barrel to make contact with the cylinder is noticeably lighter on the KWC 357's. Even the hammer is smoother and has less wiggle, just a better trigger and hammer mechanism overall.

Accuracy: This is yet to be determined but I did notice on the KWC Airsoft versions of their shell loading Airsoft Revolvers, that they do have a built in preset Hop-up by way of a small rubber bar that goes along the top of the barrel just inside the rear portion. This will create some backspin which will keep the Airsoft BB's trajectory more level but should also help them stay more accurate in general as compared to a plastic Airsoft BB that is not spinning but rather just floating through the air.

Build Quality: The KWC 357 2.5 Inch CO2 Airsoft Revolver being mostly metal has a very good build quality, perhaps even better than the Dan Wesson and S&W 327 TRR8 shell loading revolvers, even the weight of the KWC 357 is noticeably more! The only real plastic or rubber I could find was in the grips and the shell tips. Fit and finish was also good with no noticeable wear or sloppy workmanship.

Realism: The KWC 357 2.5 Inch CO2 Airsoft Revolver overall is a close copy a the real steel 357 styled revolver. I did notice the rear portion of the receiver (between the rear cylinder and hammer) to be a bit longer perhaps to accommodate the CO2 valve length, but other than that this pistol is super close to the original 357 styled revolver it is based on. Again being all metal gives this CO2 Airsoft revolver very realistic weight and feel and the loadable brass shells make using this gun almost exactly like using a real shell loading revolver but for much less cost per shot and of course a lot less recoil on the hands that a real 357 magnum or even when shooting 38 special shells for that matter ;)

Available in the:Replica Airguns Store.

Pros:

  • Shell loading revolver adds to the realism!

  • Mostly all metal design.

  • Pretty all the parts work as they would in a similar real steel revolver of this type.

  • Good overall weight, Very dense because of the shorter barrel.

  • Should have good overall power, accuracy and shots per CO2 (based on Colt Python testing).

  • Fully adjustable rear sight for windage and elevation.

  • Well hidden CO2 Screw.

  • Recessed barrel.

  • Not much white writing on the gun.

  • Nice easy Trigger pull in both single and double action.

Cons:

  • Short 2.25 inch barrel will rob power but the Dan Wesson style long barrel Airsoft revolvers are know to be a bit hot for some Airsoft games so this may be a good thing.

  • Grips may be a bit large for people with small hands.

  • All black sights with no white dots are not great on dark backgrounds or low lighting.

Comments:

The KWC 357 2.5 Inch CO2 Airsoft Revolver is yet another addition to the increasing lineup of shell loading revolvers available today in both Steel BB and Airsoft versions. The 2.5 inch reviewed here is meant to be the compact version with its snub nosed barrel but I would have to say it is not a small gun at all coming in at 2 pounds and with rather large grips and a pretty large cylinder to pack around. But then again, that may be just what you are looking for? The shorter barrel will lower the fps a bit which may bring it back in line with the requirements of some Airsoft fields and the addition of the built in preset Hop-up, this pistol should shoot pretty well out at medium and even longer ranges.

My Vimeo Table Top Review for the KWC 357 2.5 Inch CO2 Airsoft Revolver:

Categories: 6mm, Airsoft, CO2, Comparison, Pistol, Review, Revolver, Semi Auto, YouTube Video Tags: 357, KWC

KWC 357 6 Inch Chrome CO2 BB Revolver Table Top Review

12 Comments

Type: BB air revolver.

Manufacturer:KWC.

Model:357.

Materials: Mostly metal with some plastic construction.

Weight: 2.75 pounds (1218 grams).

Barrel: 5.5 inches, non-rifled.

Propulsion: 12 gram CO2.

Action: Revolver, single & double actions.

Ammunition Type: 4.5mm steel BB's.

Ammunition Capacity: 6 rounds.

FPS: 400fps.

Trigger Pull: The trigger pull on the KWC 357 6 Inch CO2 BB Revolver is good in both single and double action, even better than the Dan Wesson and S&W 327 TRR8 shell loading revolvers, most likely because the spring tension that pushes the inner barrel to make contact with the cylinder is noticeably lighter on the KWC 357. Even the hammer is smoother and has less wiggle, just a better trigger and hammer mechanism overall.

Accuracy:Based on my results shooting the Umarex Colt Python 357 which is essentially the same gun in a different finish. The results I got shooting my 6 round group from a 30 foot out semi rested position where good overall. Vertically there was about a 2 inch spread while horizontally there was about a 1 inch spread. I did find the plastic tips on the brass shells seemed to be a bit tight at first and this is when I did most of my Chronograph and target shooting. I believe the tightness effected the consistency of the FPS which also effected the accuracy especially up and down. I did get one shot out of the Umarex Colt Python 357 well over the claimed 400 fps but again the fps was rather erratic most likely because of the snug BB fit due to shell break-in.

Build Quality: The KWC 357 6 Inch CO2 BB Revolver being mostly metal has a very good build quality, perhaps even better than the Dan Wesson and S&W 327 TRR8 shell loading revolvers, even the weight of the KWC 357 came in close to a half of a pound more! The only real plastic I could find was in the grips and the shell tips. Fit and finish was also good with no noticeable chrome wear or sloppy workmanship. It will be interesting to see how the Chrome finish wears over time...

Realism: The KWC 357 6 Inch CO2 BB Revolver overall is a close copy a the real steel 357 styled revolver. I did notice the rear portion of the receiver (between the rear cylinder and hammer) to be a bit longer perhaps to accommodate the CO2 valve length, but other than that this pistol is super close to the original 357 styled revolver it is based on. Again being all metal gives this CO2 BB revolver very realistic weight and feel and the loadable brass shells make using this gun almost exactly like using a real shell loading revolver but for much less cost per shot and of course a lot less recoil on the hands.

Available in the:Replica Airguns Store.

Pros:

  • It's a revolver with actual shells! Give you the feeling of loading and shooting a real revolver.

  • Mostly all metal design.

  • lots of detail, well made, Chrome looks nice, not sure if it will ear better than the black finish?

  • Good overall weight, heaviest out of all the shell loaders.

  • Should have good overall power, accuracy and shots per CO2 (based on Colt Python testing).

  • Fully adjustable sights for windage and elevation.

  • Well hidden CO2 Screw.

  • Recessed barrel.

  • Nice easy Trigger pull in both single and double action.

Cons:

  • Grips are a bit rough.

  • Grips may be a bit large for people with small hands.

  • Black rear sight may not be great on dark backgrounds or low lighting.

Comments:

The ASG Dan Wesson shell loading revolvers reintroduced me to the joy of loading and shooting a revolver which up until that point was not that realistic of an experience when using a BB or Pellet revolver. The KWC 357 6 Inch CO2 BB Revolver like the Umarex Colt Python 357 has taken it up a notch by adding just a bit more overall weight, a smother trigger and hammer mechanism and styling this revolver on the Classic 357 magnum platform. And all of this for even less than the cost of the original Dan Wesson shell loading series CO2 BB revolvers. If you're a revolver fan, make sure to grab one of these, the Chrome finish is really eye catching and would make a great addition to your revolver collection for sure.

My Vimeo Table Top Review for the KWC 357 6 Inch CO2 BB Revolver:

 
Categories: 4.5mm / .177 cal, BB, CO2, Comparison, Pistol, Review, Revolver, YouTube Video Tags: 357, Colt Python 357, KWC

KWC 357 and ASG CZ 75 P-07 - CZ 75D Compact and Bersa BP9CC BB and Airsoft Update Video

1 Comment

Some more CO2 pistols I will be doing Table Top and Field Test video reviews for in the near future. Some of them I have already reviewed in different caliber versions, either 4.5mm Steel BB or 6mm Plastic Airsoft.

From KWC I show off two revolvers styled after the 357 and if you watched my Umarex Colt Python 357 Review then you will notice the similarities between these KWC made revolvers since they are all made by KWC. The Model 357 6 inch version is finished in Chrome and made to shoot 4.5mm Steel BB's while the KWC Model 357 2.5 inch shoots 6mm Plastic BB's and is in all black. At this time I do not have these KWC revolver listed in the Replica Airguns Canada Store but should have them listed fairly soon...

I also showcase three CO2 6mm Airsoft semi auto pistols from ASG that I have already reviewed in their 4.5mm Steel BB equivalents. The ASG CZ 75 P-07 Duty Non-blowback, the ASG CZ 75 D Compact Non-blowback and the ASG Bersa BP9CC Blowback.

Make sure to watch my quick Update Vimeo Preview Video for these fine CO2 pistols to see them up close and personal...

 
Categories: 4.5mm / .177 cal, 6mm, Airsoft, BB, Blowback, CO2, Comparison, Pistol, Review, Revolver, Semi Auto, YouTube Video Tags: 357, ASG, Bersa, CZ 75 P-07 Duty, CZ 75D, KWC

What is an Uncontrolled Firearm in Canada?

6 Comments

This Article and Video expresses my views and opinions on this matter and should not be taken as legal advice.

Main points covered:

  • Uncontrolled Firearms do not require a Firearms License within Canada to own and operate.

  • What is an Uncontrolled Airgun and Airsoft Gun?

  • What is an Uncontrolled Blank Gun / Starter Pistols?

  • What about Fully Automatic Airguns and Airsoft Guns?

  • What about Replica Guns?

NOTE: Controlled Firearms require a POL (Possession Only License) , PAL (Possession Acquisition License) or R-PAL (Restricted Possession Acquisition License) within Canada to own and operate. 

MEMORANDUM D19-13-2

Firearm – a barreled weapon from which any shot, bullet, or other projectile can be discharged and that is capable of causing serious bodily injury or death to a person, and includes any frame or receiver of such a barreled weapon and anything that can be adapted for use as a firearm.

“Uncontrolled”firearms are those devices that, although falling within the definition of a firearm in the Criminal Code, are exempt from specific legal requirements of the Firearms Act and its regulations, as well as from other legislative provisions. “Uncontrolled” firearms should not be subdivided into any of the non-restricted, restricted, or prohibited classes. The following types of firearms are deemed “uncontrolled”:

Flare, blank, rivet and industrial guns: Any device that is designed exclusively for signaling, for notifying of distress, or for firing blank cartridges or for firing stud cartridges, explosive-driven rivets or other industrial projectiles, provided that the importer intends to use it only for the purpose for which it is designed.

NOTE: (Toy guns and starter pistols do not generally qualify as firearms. However, some toy or model guns and starter pistols may be designed with very realistic mechanisms or appearances (e.g., color, size, scale, translucency) and resembling a real make and model of a firearm. In such cases, they may be considered replica firearms even if they are made of plastic, die cast zinc, or other material.)

Low muzzle velocity/energy guns: Any barreled weapon that is not designed or adapted to discharge projectiles at a muzzle velocity exceeding 152.4 meters per second (500 feet per second) and at a muzzle energy exceeding 5.7 Joules, or to discharge projectiles that are designed or adapted to attain a velocity exceeding 152.4 meters per second (500 feet per second) and an energy exceeding 5.7 Joules. Both thresholds of 152.4 mps and 5.7 Joules must be exceeded for the firearm to be considered “controlled”. This requirement exempts firearms that fire below the threshold velocity with a standard projectile, but exceed the threshold velocity when fired with a high-velocity projectile. 

Airsoft guns and certain types of paintball guns or markers may qualify as a replica firearm, if the muzzle velocity of the projectile does not cause serious bodily harm and their external features are clearly designed to resemble a specific and readily identifiable make and model of a firearm. To be considered a firearm, within the meaning of the Criminal Code, an airsoft gun must have a muzzle velocity in excess of 111.6 meters per second (366 feet per second).

NOTE: This memorandum used to state when using a .20 gram BB but does not specify this BB weight anymore?

NOTE: The term air gun is a colloquial term referring to BB or pellet guns. Such guns operate either as spring- powered, gas-powered, or electrically powered. If the muzzle velocity of the air gun is less than 152.4 mps (500 fps)/5.7 joules but still able to cause serious bodily injury to a person, it may be considered an “uncontrolled” firearm. Airsoft guns and certain types of paintball guns may qualify as a replica firearm (see paragraph 49 of this memorandum).

Replica firearms:

“Replica firearm” is defined as any device that is designed or intended to exactly resemble, or to resemble with near precision, a firearm, and that itself is not a firearm, but does not include any such device that is designed or intended to exactly resemble, or to resemble with near precision, an antique firearm.

For a device to be a replica firearm it must meet all three requirements:

  • (a) it cannot be a firearm, meaning it does not discharge a projectile with sufficient energy to cause serious bodily injury or death to a person. If the device is a firearm, then it cannot be a replica firearm (and vice versa);

  • (b) it must resemble exactly, or with near precision, a real existing firearm of an identifiable make and model. With respect to visual examination, note that the maximum observing distance is one at which the equivalent make and model of the firearm can be identified. This distance will vary from one firearm make to the next. For example: A Luger pistol has a very distinctive silhouette as compared to other makes and is therefore more readily identified from further away. The examination of the object is something more than casual, but less than detailed. The device does not need to be so close that markings are identifiable; and

  • (c) it cannot be designed or intended to exactly resemble, or to resemble with near precision, an antique firearm. 

RCMP Website "Air Guns"

1. Air guns that are "Controlled" Firearms for purposes of both the Firearms Act and the Criminal Code

These are air guns with both a high muzzle velocity (greater than 152.4 meters or 500 feet per second) and a high muzzle energy (greater than 5.7 joules or 4.2 foot-pounds). The "muzzle velocity" is the speed of a projectile at the instant it leaves the muzzle of a gun, normally expressed in meters per second or feet per second. The "muzzle energy" is the energy of a projectile at the instant it leaves the muzzle of a gun, expressed in joules or foot-pounds. Air guns need to meet both standards to be classified as "Controlled" firearms for purposes of the Firearms Act.

These high-powered air guns are subject to the same license and registration requirements as a conventional "Controlled" firearm. Owners and users are also required to store, transport, display and handle them safely in accordance with the regulations supporting the Firearms Act.

Usually, the manufacturer's specifications are used to determine what muzzle velocity and muzzle energy an air gun was designed to have. This information may be available in the user's manual or on the manufacturer's website. If the information is not available, individuals can call the Royal Canadian Mounted Police Canadian Firearms Program (CFP) at 1-800-731-4000 and ask to speak to a firearm technician to find out if the air gun is considered to be a firearm for purposes of the Firearms Act.

High-powered air rifles are generally classified as non-restricted firearms. However, the classification depends on the exact design of the air gun. Air rifles manufactured to resemble an assault rifle could be non-restricted, restricted or prohibited depending on the exact model imitated. High-powered air rifles would also be prohibited firearms if fully automatic or if they have a sawed-off barrel. They could also be restricted firearms if they have a folding stock that reduces the overall length to less than 660mm. 

Additional thought on this subject: Even though Uncontrolled Firearms are not governed by the same laws that apply to Controlled Firearms within the Firearms act and do not need to be handled or stored similar in the same way you are required to handle, transport and store a Controlled Firearm, we need to treat our Uncontrolled Airguns, Airsoft Guns and Blank guns with care and go over and above what is expected when had handle, transport and store them.

Categories: Airsoft, BB, Blank Gun, Full Auto, Gun Law, Gun Safety, Non Airguns, Paintball, Pellet, Pistol, Real Gun, Revolver, Rifle, YouTube Video Tags:

Large Umarex Order Just Arrived in Canada - Lots of Stock on Hand

No Comments

Categories: 4.5mm / .177 cal, BB, Blowback, CO2, Full Auto, Pellet, Pistol, Replica Airguns News, Revolver, Rifle, Semi Auto, Single Shot, Spring Piston Tags: Umarex

Swiss Arms 4 & 6 inch Full Metal Revolvers Added to the US Store

No Comments

We have just added the Swiss Arms 4 inch & 6 inch Full Metal Revolvers to the US Store, these are basically teh KWC made guns licensed through Cybergun with the Swiss Arms licensing so you can check out my Umarex Colt Python 357 since it too is the same base gun made by  KWC.

Here are the specs for these Shell loading 357 styled CO2 4.5mm BB Revolvers.

6 Inch Barrel Length Model

  • FPS: 410
  • Mag Capacity: 6 rounds
  • Power CO2
  • Length: 11.42 inches
  • Weight: 2.67 lbs
  • Full Metal, Rubberized Plastic, Textured Grips
  • Rotating Cylinder, Manual Safety, Working Ejector Rod
  • Single & Double Action
  • Includes: 1 Gun, 6 Realistic Shells, 1 Speed Loader

4 Inch Barrel Length Model

  • FPS: 344
  • Mag Capacity: 6 rounds
  • Power CO2
  • Length: 9.44 inches
  • Weight: 2.39 lbs
  • Full Metal, Rubberized Plastic, Textured Grips
  • Rotating Cylinder, Manual Safety, Working Ejector Rod
  • Single & Double Action
  • Includes: 1 Gun, 6 Realistic Shells, 1 Speed Loader
Categories: 4.5mm / .177 cal, BB, CO2, Pistol, Replica Airguns News, Revolver Tags: Cybergun, KWC, Swiss Arms

Umarex Colt Python 357 BB Revolver Field Test Shooting Review

2 Comments

First off, make sure to checkout my Table Top Review for the Umarex Colt Python 357 CO2 BB Revolver so you can get the specs and details on this fine shell loading BB pistol.

In this Field Test Shooting Video I do my traditional Chronograph test where I shoot a series of 4.5mm Steel BB's using a brand new CO2 cartridge to see what kind of real word Feet Per Second performance I can get out of the Umarex Colt Python. On this day I averages right around 390 fps which was very close to the claimed 360 fps form Umarex. The temperature was right around 24 Celsius or 75 Fahrenheit so it was neither cold or hot.

Moving on with the Accuracy Shooting Test, I set myself up 30 feet away using a semi-rested stance (Sand bag up front, standing in the back) I got one of my best ever 6 shot groups from the Umarex Colt 357, coming in at just under 1 inch. During my previous pretest, the Umarex Revolver did well but seemed to spread out a bit vertically, this may have been due to the plastic tips on the shells needing to break in for a more consistent BB fit.

The Umarex Colt Python 357 has taken it up a notch by adding just a bit more overall weight than most comparable shell loading BB revolvers, a smother trigger and hammer mechanism and styling this revolver on the Classic Colt Python platform. If you're a revolver fan, make sure to grab one of these and if you're not a revolver fan, this pistol may just change your mind :)

 Buy the Umarex Colt Python 357 in Canada

Buy the Umarex Colt Python 357 in the US

Categories: 4.5mm / .177 cal, BB, CO2, Field Test, Pistol, Review, Revolver, Semi Auto, YouTube Video Tags: Colt Python 357, Umarex

Umarex Colt Python 357 CO2 BB Revolver Table Top Review

2 Comments

Type: BB air revolver.

Manufacturer:UmarexUSA.

Model: Colt Python 357.

Materials: Mostly metal with some plastic construction.

Weight: 2.75 pounds (1218 grams).

Barrel: 5.5 inches, non-rifled.

Propulsion: 12 gram CO2.

Action: Revolver, single & double actions.

Ammunition Type: 4.5mm steel BB's.

Ammunition Capacity: 6 rounds.

FPS: 400fps.

Trigger Pull: The trigger pull on the Colt Python 357 CO2 BB Revolver is good in both single and double action, even better than the Dan Wesson and S&W 327 TRR8 shell loading revolvers, most likely because the spring tension that pushes the inner barrel to make contact with the cylinder is noticeably lighter on the Umarex Colt Python 357. Even the hammer is smoother and has less wiggle, just a better trigger and hammer mechanism overall.

Accuracy: The results I got shooting my 6 round group from a 30 foot out semi rested position where good overall. Vertically there was about a 2 inch spread while horizontally there was about a 1 inch spread. I did find the plastic tips on the brass shells seemed to be a bit tight at first and this is when I did most of my Chronograph and target shooting. I believe the tightness effected the consistency of the FPS which also effected the accuracy especially up and down. I did get one shot out of the Umarex Colt Python 357 well over the claimed 400 fps but again the fps was rather erratic most likely because of the snug BB fit due to shell break-in.

Build Quality: The Umarex Colt Python 357 being mostly metal, you would expect it to have a decent build quality and I am happy to say it does, perhaps again even better than the Dan Wesson and S&W 327 TRR8 shell loading revolvers, even the weight of the Colt Python came in close to a half of a pound more! The only real plastic I could find was in the grips and the shell tips. Fit and finish was also good with no noticeable paint wear or sloppy workmanship.

Realism: The Colt Python 357 CO2 BB Revolver overall is a close copy of the real steel Colt Python 357. I did notice the rear portion of the receiver (between the rear cylinder and hammer) to be a bit longer perhaps to accommodate the CO2 valve length, but other than that this pistol is super close to the original revolver it is based and licensed on. Agin being all metal gives this CO2 BB revolver very realistic weight and feel and the loadable brass shells make using this gun almost exactly like using a real shell loading revolver but for much less cost per shot and of course a lot less recoil on the hands.

Available in the: Replica Airguns Store

Pros:

  • It's a revolver with actual shells! Give you the feeling of loading and shooting a real revolver.

  • Mostly all metal design.

  • lots of detail, well made, fit and finish is very good.

  • Good overall weight, heaviest out of all the shell loaders.

  • Good overall power, accuracy and shots per CO2.

  • Fully adjustable sights for windage and elevation.

  • Well hidden CO2 Screw.

  • Recessed barrel.

  • Nice easy Trigger pull in both single and double action.

Cons:

  • Grips are a bit rough.

  • All black sights not great on dark backgrounds.

  • FPS seemed to fluctuate a bit 

Comments:

The ASG Dan Wesson shell loading revolvers reintroduced me to the joy of loading and shooting a revolver which up until that point was not that realistic of an experience when using a BB or Pellet revolver. The Umarex Colt Python 357 has taken it up a notch by adding just a bit more overall weight, a smother trigger and hammer mechanism and styling this revolver on the Classic Colt Python platform. And all of this for even less than the cost of the original Dan Wesson shell loading series CO2 BB revolvers. If you're a revolver fan, make sure to grab one of these and if you're not a revolver fan, this pistol may just change your mind :)

My Vimeo Table Top Review for the Umarex Colt Python 357 CO2 BB Revolver:

 
Categories: 4.5mm / .177 cal, BB, CO2, Field Test, Pistol, Review, Revolver, Semi Auto, YouTube Video Tags: 357, Colt Python 357, Umarex

Umarex Walther PPS and Colt Python 357 CO2 BB Pistol Preview Video

No Comments

In this Vimeo Update Video Preview I show you around two brand new Umarex CO2 BB pistols, the Umarex Walther PPS and the Umarex Colt Python 357, both recently added to our online Replica Airguns Store.

The Umarex Walther PPS is a full licensed CO2 BB Blowback replica of the real steel super compact Walther PPS and it compares well to the ASG Bersa BP9CC that I reviewed earlier and by the way ended up being one of my favorite compact air pistols. That said I think the Umarex Walther PPS is the new king! It is even more compact yet has great fps for a super small CO2 pistol, shot very accurate even from 30 feet out and has more blowback recoil than the larger Bersa BP9CC!

Here are some of the specifications for the Walther PPS CO2 Blowback 4.5mm BB Pistol:

  • Velocity: 350 fps

  • Length: 6.4”

  • Barrel Length: 3”

  • Weight: 1.2lbs

  • Magazine Capacity: 18 Rounds

  • Power: 12 gram CO2

  • Ammo: 4.5mm Steel BB

  • Material: Metal and Plastic

  • Action: Blowback Single Action Only

Umarex added another shell loading revolver to their collection, the fully licensed Colt Python 357 and again this revolver uses CO2 and shoots 4.5mm Steel BB's that are preloaded into 6 included brass shells. Out of all the 4.5mm shell loading revolvers to date, I have to say the Colt Python 357 is the heaviest coming in at just under 3 pounds. The trigger hammer combination is also very smooth and it has a fully adjustable rear sight for windage and elevation.

Here are some of the specifications for the Colt Python 357 4.5mm BB Revolver:

  • Velocity: 400 fps

  • Length: 11.75”

  • Barrel Length: 5.5”

  • Weight: 2.75lbs

  • Magazine Capacity: 6 Rounds

  • Power: 12 gram CO2

  • Ammo: 4.5mm Steel BB

  • Material: Almost all Metal

  • Action: Single and Double Action

Watch my Vimeo Preview Video of the Umarex Walther PPS and Colt Python 357 BB Pistols:

Categories: 4.5mm / .177 cal, BB, Blowback, CO2, Field Test, Pistol, Review, Revolver, Semi Auto, YouTube Video Tags: Colt Python 357, Umarex, Walther, Walther PPS

CO2 Versus Spring Versus Pump Airgun Comparison

7 Comments

In this Comparison Video I go through the benefits and shortcomings of CO2, Spring Piston and Pump Airguns. I focus mainly on Airguns but there is a bit of a crossover with Airsoft guns.

All three systems (CO2, Spring, Pump) create pressure that forces the ammunition with a high force out of the barrel. Similar to how gun powder is the source of energy for a bullet.

Here are some basic statements that best describe CO2, Spring Piston and Pump Airguns.

CO2 Airguns:

  • CO2 Airguns use the expansion of CO2 gas to create the pressure required for the ammo.

  • CO2 Airguns generally store enough CO2 for multiple shots per cartridge.

  • CO2 Airguns have a limit as to how much power they can produce since CO2 has a set vapor pressure of 850 psi, or about 56 bar at room temperature which is around 25 C or 77 F. CO2 Gas also requires a warm environment to expand so warmer temperature and longer barrels help with power.

  • Some CO2 guns can also use pressurized air tanks in place of CO2.

Spring Piston Airguns:

  • Spring Airguns use the release of a pre-cocked spring and plunger system to compress air to power the ammo.

  • Spring Piston Airguns require the cocking of the spring between each shot so they are single shot only.

  • Spring Airguns are limited to how much effort is humanly possible to cock the spring into position. If you make the spring to strong then not everyone will be able to use the Airgun effectively. Too week of a spring and the Airgun will lack power.

  • Spring Piston Airguns are known for having a fair amount of recoil and vibration when the spring moves both forward and backwards quickly inside the Airgun.

  • Spring Airguns can use either a mechanical spring or a gas spring.

Pump Airguns:

  • Pump Airguns (either Single or Multi-Pump) store air pressure in a chamber that when released, powers the ammo.

  • Most Pump Airguns require at least 1 or more pumps, often up to 10 pumps for each shot and you generally only get one shot per set of pumps. Not to be confused with PCP Airguns (Pre Charged Pneumatic) which have large pressure tanks that are recharged with a high volume of pressurized air that is capable of shooting multiple shots per charge.

  • Pump Airguns are also somewhat limited to how much effort is humanly possible since the higher the chamber pressure, the harder it will be to pump the Airgun. 

Misc Airguns:

  • Generally speaking both Spring and Multi-Pump Airguns have more potential power than a CO2 guns since CO2 has a set peek pressure limit.

  • Pump and CO2 Airguns are know to have very little recoil since the pressure is stored in a chamber and then released by a valve. No slapping back and forth of a large internal spring.

Pros:

CO2 Airguns:

  • CO2 Airguns allow for multiple shots per CO2 cartridge for more realistic action shooting.

  • CO2 Airguns do not require any human effort to charge the gun other than loading the CO2 and Ammo into the Airgun.

  • CO2 Airguns allow for true semi auto shooting ability. 

Spring Piston Airguns:

  • Spring Airguns have the potential for high velocity since the larger and stiffer the spring, the greater the output force.

  • Spring Airguns do not require anything other than your ammunition, typically either a Pellet or BB.

  • Spring Airguns are mechanically very simple which makes them very reliable and less expensive to produce than other types of Airguns. 

Pump Airguns:

  • Pump Airguns have the potential for high velocity since more pumps equals greater output force, only limited by the users strength and the pressure rating of the Airgun.

  • Pump Airguns do not require anything other than your ammunition, typically either a Pellet or BB.

  • Pump Airguns have next to no recoil which makes them very easy to shoot and highly accurate.

Cons:

CO2 Airguns:

  • CO2 Airguns require the purchase and use of CO2 or they simple do not work.

  • CO2 Airguns are very susceptible to temperature changes, especially cold temperature since CO2 needs a warm environment in order to expand. Cool down effect also plays a role in power output.

  • CO2 Airguns have a maximum set amount of power output.

Spring Piston Airguns:

  • Spring Airguns require the pre-cocking of the spring for each shot.

  • Spring Airguns can take some getting used to since the spring recoil/vibration requires a very lose grip (Military Grip) to shoot accurately with them.

  • Spring Airguns should not be stored pre-cocked since this can damage the spring, less so with gas spring versions. 

Pump Airguns:

  • Pump Airguns require pre-pumping to pressurize the air chamber for each shot.

  • Pump Airguns, especially Multi-Pump Airguns take the most amount of human effort for each shot.

  • Pump Airguns need to stored with at least one pump in them or the seals can get damaged over time.

Categories: .22 cal, 4.5mm / .177 cal, BB, Break Barrel, CO2, Comparison, Multi-pump, PCP, Pellet, Pistol, Repeater, Revolver, Rifle, Semi Auto, Spring Piston Tags: