Type: Airsoft revolver.

Manufacturer:KWC.

Model:357.

Materials: Mostly metal with some plastic construction.

Weight: 2 pounds (900 grams).

Barrel: 2.25 inches, non-rifled.

Propulsion: 12 gram CO2.

Action: Revolver, single & double actions.

Ammunition Type: 6mm plastic Airsoft BB's.

Ammunition Capacity: 6 rounds.

FPS: 360+.

Trigger Pull: The trigger pull on the KWC 357 2.5 Inch CO2 Airsoft Revolver is good in both single and double action, even better than the Dan Wesson and S&W 327 TRR8 shell loading revolvers, most likely because the spring tension that pushes the inner barrel to make contact with the cylinder is noticeably lighter on the KWC 357's. Even the hammer is smoother and has less wiggle, just a better trigger and hammer mechanism overall.

Accuracy: This is yet to be determined but I did notice on the KWC Airsoft versions of their shell loading Airsoft Revolvers, that they do have a built in preset Hop-up by way of a small rubber bar that goes along the top of the barrel just inside the rear portion. This will create some backspin which will keep the Airsoft BB's trajectory more level but should also help them stay more accurate in general as compared to a plastic Airsoft BB that is not spinning but rather just floating through the air.

Build Quality: The KWC 357 2.5 Inch CO2 Airsoft Revolver being mostly metal has a very good build quality, perhaps even better than the Dan Wesson and S&W 327 TRR8 shell loading revolvers, even the weight of the KWC 357 is noticeably more! The only real plastic or rubber I could find was in the grips and the shell tips. Fit and finish was also good with no noticeable wear or sloppy workmanship.

Realism: The KWC 357 2.5 Inch CO2 Airsoft Revolver overall is a close copy a the real steel 357 styled revolver. I did notice the rear portion of the receiver (between the rear cylinder and hammer) to be a bit longer perhaps to accommodate the CO2 valve length, but other than that this pistol is super close to the original 357 styled revolver it is based on. Again being all metal gives this CO2 Airsoft revolver very realistic weight and feel and the loadable brass shells make using this gun almost exactly like using a real shell loading revolver but for much less cost per shot and of course a lot less recoil on the hands that a real 357 magnum or even when shooting 38 special shells for that matter ;)

Available in the:Replica Airguns Store.

Pros:

• Shell loading revolver adds to the realism!

• Mostly all metal design.

• Pretty all the parts work as they would in a similar real steel revolver of this type.

• Good overall weight, Very dense because of the shorter barrel.

• Should have good overall power, accuracy and shots per CO2 (based on Colt Python testing).

• Fully adjustable rear sight for windage and elevation.

• Well hidden CO2 Screw.

• Recessed barrel.

• Not much white writing on the gun.

• Nice easy Trigger pull in both single and double action.

Cons:

• Short 2.25 inch barrel will rob power but the Dan Wesson style long barrel Airsoft revolvers are know to be a bit hot for some Airsoft games so this may be a good thing.

• Grips may be a bit large for people with small hands.

• All black sights with no white dots are not great on dark backgrounds or low lighting.

Comments:

The KWC 357 2.5 Inch CO2 Airsoft Revolver is yet another addition to the increasing lineup of shell loading revolvers available today in both Steel BB and Airsoft versions. The 2.5 inch reviewed here is meant to be the compact version with its snub nosed barrel but I would have to say it is not a small gun at all coming in at 2 pounds and with rather large grips and a pretty large cylinder to pack around. But then again, that may be just what you are looking for? The shorter barrel will lower the fps a bit which may bring it back in line with the requirements of some Airsoft fields and the addition of the built in preset Hop-up, this pistol should shoot pretty well out at medium and even longer ranges.

My Vimeo Table Top Review for the KWC 357 2.5 Inch CO2 Airsoft Revolver:

Buy Airsoft Pistols in Canada 

Buy Airsoft Pistols in the US

Buy theKWC Black 2.5 Inch Airsoft Revolver

Type: BB air revolver.

Manufacturer:KWC.

Model:357.

Materials: Mostly metal with some plastic construction.

Weight: 2.75 pounds (1218 grams).

Barrel: 5.5 inches, non-rifled.

Propulsion: 12 gram CO2.

Action: Revolver, single & double actions.

Ammunition Type: 4.5mm steel BB's.

Ammunition Capacity: 6 rounds.

FPS: 400fps.

Trigger Pull: The trigger pull on the KWC 357 6 Inch CO2 BB Revolver is good in both single and double action, even better than the Dan Wesson and S&W 327 TRR8 shell loading revolvers, most likely because the spring tension that pushes the inner barrel to make contact with the cylinder is noticeably lighter on the KWC 357. Even the hammer is smoother and has less wiggle, just a better trigger and hammer mechanism overall.

Accuracy:Based on my results shooting the Umarex Colt Python 357 which is essentially the same gun in a different finish. The results I got shooting my 6 round group from a 30 foot out semi rested position where good overall. Vertically there was about a 2 inch spread while horizontally there was about a 1 inch spread. I did find the plastic tips on the brass shells seemed to be a bit tight at first and this is when I did most of my Chronograph and target shooting. I believe the tightness effected the consistency of the FPS which also effected the accuracy especially up and down. I did get one shot out of the Umarex Colt Python 357 well over the claimed 400 fps but again the fps was rather erratic most likely because of the snug BB fit due to shell break-in.

Build Quality: The KWC 357 6 Inch CO2 BB Revolver being mostly metal has a very good build quality, perhaps even better than the Dan Wesson and S&W 327 TRR8 shell loading revolvers, even the weight of the KWC 357 came in close to a half of a pound more! The only real plastic I could find was in the grips and the shell tips. Fit and finish was also good with no noticeable chrome wear or sloppy workmanship. It will be interesting to see how the Chrome finish wears over time...

Realism: The KWC 357 6 Inch CO2 BB Revolver overall is a close copy a the real steel 357 styled revolver. I did notice the rear portion of the receiver (between the rear cylinder and hammer) to be a bit longer perhaps to accommodate the CO2 valve length, but other than that this pistol is super close to the original 357 styled revolver it is based on. Again being all metal gives this CO2 BB revolver very realistic weight and feel and the loadable brass shells make using this gun almost exactly like using a real shell loading revolver but for much less cost per shot and of course a lot less recoil on the hands.

Available in the:Replica Airguns Store.

Pros:

• It's a revolver with actual shells! Give you the feeling of loading and shooting a real revolver.

• Mostly all metal design.

• lots of detail, well made, Chrome looks nice, not sure if it will ear better than the black finish?

• Good overall weight, heaviest out of all the shell loaders.

• Should have good overall power, accuracy and shots per CO2 (based on Colt Python testing).

• Fully adjustable sights for windage and elevation.

• Well hidden CO2 Screw.

• Recessed barrel.

• Nice easy Trigger pull in both single and double action.

Cons:

• Grips are a bit rough.

• Grips may be a bit large for people with small hands.

• Black rear sight may not be great on dark backgrounds or low lighting.

Comments:

The ASG Dan Wesson shell loading revolvers reintroduced me to the joy of loading and shooting a revolver which up until that point was not that realistic of an experience when using a BB or Pellet revolver. The KWC 357 6 Inch CO2 BB Revolver like the Umarex Colt Python 357 has taken it up a notch by adding just a bit more overall weight, a smother trigger and hammer mechanism and styling this revolver on the Classic 357 magnum platform. And all of this for even less than the cost of the original Dan Wesson shell loading series CO2 BB revolvers. If you're a revolver fan, make sure to grab one of these, the Chrome finish is really eye catching and would make a great addition to your revolver collection for sure.

My Vimeo Table Top Review for the KWC 357 6 Inch CO2 BB Revolver:

Buy the Umarex Colt Python 357 in Canada

Buy the Umarex Colt Python 357 in the US

Some more CO2 pistols I will be doing Table Top and Field Test video reviews for in the near future. Some of them I have already reviewed in different caliber versions, either 4.5mm Steel BB or 6mm Plastic Airsoft.

From KWC I show off two revolvers styled after the 357 and if you watched my Umarex Colt Python 357 Review then you will notice the similarities between these KWC made revolvers since they are all made by KWC. The Model 357 6 inch version is finished in Chrome and made to shoot 4.5mm Steel BB's while the KWC Model 357 2.5 inch shoots 6mm Plastic BB's and is in all black. At this time I do not have these KWC revolver listed in the Replica Airguns Canada Store but should have them listed fairly soon...

I also showcase three CO2 6mm Airsoft semi auto pistols from ASG that I have already reviewed in their 4.5mm Steel BB equivalents. The ASG CZ 75 P-07 Duty Non-blowback, the ASG CZ 75 D Compact Non-blowback and the ASG Bersa BP9CC Blowback.

Make sure to watch my quick Update Vimeo Preview Video for these fine CO2 pistols to see them up close and personal...

Buy Umarex Colt Python in Canada

Buy Umarex Colt Python in the US

Buy ASG CZ 75D Compact CO2 Pistol in Canada

Buy ASG CZ 75D Compact CO2 Pistol in the US

Buy ASG CZ 75 P-07 in Canada

Buy ASG CZ 75 P-07 in the US

Buy ASG Bersa BP9CC in Canada

Buy ASG Bersa BP9CC in the US

If you have been watching my Full Auto Fun Videos, then you will have noticed that I have recently been using Clay Pigeons as my go-to targets. Generally Clay Pigeons are shot from launchers and used with shotguns since the flight of the Clay Pigeon simulates a bird in flight nicely.

So I thought, why not use them as reactive targets for my Airguns and Airsoft guns? It turns out they work pretty darn good, well at least with 4.5mm Steel BB pistols and I would imagine even better with pellet guns. What about Airsoft guns, will the Airsoft lighter weight plastic BB's have enough mass to get the job done?

You'll have to watch this video to find out the answer to that question when I unload a full magazine of .20 gram Airsoft BB's into some Clay Pigeons using my KWC .50 Desert Eagle...

Buy KWC Airsoft Desert Eagle in Canada

Buy KWC Silver Desert Eagle in Canada 

This Article and Video expresses my views and opinions on this matter and should not be taken as legal advice.

Main points covered:

• Uncontrolled Firearms do not require a Firearms License within Canada to own and operate.

• What is an Uncontrolled Airgun and Airsoft Gun?

• What is an Uncontrolled Blank Gun / Starter Pistols?

• What about Fully Automatic Airguns and Airsoft Guns?

• What about Replica Guns?

NOTE: Controlled Firearms require a POL (Possession Only License) , PAL (Possession Acquisition License) or R-PAL (Restricted Possession Acquisition License) within Canada to own and operate. 

MEMORANDUM D19-13-2

Firearm – a barreled weapon from which any shot, bullet, or other projectile can be discharged and that is capable of causing serious bodily injury or death to a person, and includes any frame or receiver of such a barreled weapon and anything that can be adapted for use as a firearm.

“Uncontrolled”firearms are those devices that, although falling within the definition of a firearm in the Criminal Code, are exempt from specific legal requirements of the Firearms Act and its regulations, as well as from other legislative provisions. “Uncontrolled” firearms should not be subdivided into any of the non-restricted, restricted, or prohibited classes. The following types of firearms are deemed “uncontrolled”:

Flare, blank, rivet and industrial guns: Any device that is designed exclusively for signaling, for notifying of distress, or for firing blank cartridges or for firing stud cartridges, explosive-driven rivets or other industrial projectiles, provided that the importer intends to use it only for the purpose for which it is designed.

NOTE: (Toy guns and starter pistols do not generally qualify as firearms. However, some toy or model guns and starter pistols may be designed with very realistic mechanisms or appearances (e.g., color, size, scale, translucency) and resembling a real make and model of a firearm. In such cases, they may be considered replica firearms even if they are made of plastic, die cast zinc, or other material.)

Low muzzle velocity/energy guns: Any barreled weapon that is not designed or adapted to discharge projectiles at a muzzle velocity exceeding 152.4 meters per second (500 feet per second) and at a muzzle energy exceeding 5.7 Joules, or to discharge projectiles that are designed or adapted to attain a velocity exceeding 152.4 meters per second (500 feet per second) and an energy exceeding 5.7 Joules. Both thresholds of 152.4 mps and 5.7 Joules must be exceeded for the firearm to be considered “controlled”. This requirement exempts firearms that fire below the threshold velocity with a standard projectile, but exceed the threshold velocity when fired with a high-velocity projectile. 

Airsoft guns and certain types of paintball guns or markers may qualify as a replica firearm, if the muzzle velocity of the projectile does not cause serious bodily harm and their external features are clearly designed to resemble a specific and readily identifiable make and model of a firearm. To be considered a firearm, within the meaning of the Criminal Code, an airsoft gun must have a muzzle velocity in excess of 111.6 meters per second (366 feet per second).

NOTE: This memorandum used to state when using a .20 gram BB but does not specify this BB weight anymore?

NOTE: The term air gun is a colloquial term referring to BB or pellet guns. Such guns operate either as spring- powered, gas-powered, or electrically powered. If the muzzle velocity of the air gun is less than 152.4 mps (500 fps)/5.7 joules but still able to cause serious bodily injury to a person, it may be considered an “uncontrolled” firearm. Airsoft guns and certain types of paintball guns may qualify as a replica firearm (see paragraph 49 of this memorandum).

Replica firearms:

“Replica firearm” is defined as any device that is designed or intended to exactly resemble, or to resemble with near precision, a firearm, and that itself is not a firearm, but does not include any such device that is designed or intended to exactly resemble, or to resemble with near precision, an antique firearm.

For a device to be a replica firearm it must meet all three requirements:

• (a) it cannot be a firearm, meaning it does not discharge a projectile with sufficient energy to cause serious bodily injury or death to a person. If the device is a firearm, then it cannot be a replica firearm (and vice versa);

• (b) it must resemble exactly, or with near precision, a real existing firearm of an identifiable make and model. With respect to visual examination, note that the maximum observing distance is one at which the equivalent make and model of the firearm can be identified. This distance will vary from one firearm make to the next. For example: A Luger pistol has a very distinctive silhouette as compared to other makes and is therefore more readily identified from further away. The examination of the object is something more than casual, but less than detailed. The device does not need to be so close that markings are identifiable; and

• (c) it cannot be designed or intended to exactly resemble, or to resemble with near precision, an antique firearm. 

RCMP Website "Air Guns"

1. Air guns that are "Controlled" Firearms for purposes of both the Firearms Act and the Criminal Code

These are air guns with both a high muzzle velocity (greater than 152.4 meters or 500 feet per second) and a high muzzle energy (greater than 5.7 joules or 4.2 foot-pounds). The "muzzle velocity" is the speed of a projectile at the instant it leaves the muzzle of a gun, normally expressed in meters per second or feet per second. The "muzzle energy" is the energy of a projectile at the instant it leaves the muzzle of a gun, expressed in joules or foot-pounds. Air guns need to meet both standards to be classified as "Controlled" firearms for purposes of the Firearms Act.

These high-powered air guns are subject to the same license and registration requirements as a conventional "Controlled" firearm. Owners and users are also required to store, transport, display and handle them safely in accordance with the regulations supporting the Firearms Act.

Usually, the manufacturer's specifications are used to determine what muzzle velocity and muzzle energy an air gun was designed to have. This information may be available in the user's manual or on the manufacturer's website. If the information is not available, individuals can call the Royal Canadian Mounted Police Canadian Firearms Program (CFP) at 1-800-731-4000 and ask to speak to a firearm technician to find out if the air gun is considered to be a firearm for purposes of the Firearms Act.

High-powered air rifles are generally classified as non-restricted firearms. However, the classification depends on the exact design of the air gun. Air rifles manufactured to resemble an assault rifle could be non-restricted, restricted or prohibited depending on the exact model imitated. High-powered air rifles would also be prohibited firearms if fully automatic or if they have a sawed-off barrel. They could also be restricted firearms if they have a folding stock that reduces the overall length to less than 660mm. 

Additional thought on this subject: Even though Uncontrolled Firearms are not governed by the same laws that apply to Controlled Firearms within the Firearms act and do not need to be handled or stored similar in the same way you are required to handle, transport and store a Controlled Firearm, we need to treat our Uncontrolled Airguns, Airsoft Guns and Blank guns with care and go over and above what is expected when had handle, transport and store them.

Hey everyone, we just got a really large Umarex order in our Canada location so if you have been waiting on some product from Umarex we should have most items in stock now...

Some of the more popular Umarex items these days are:

• Umarex Steel Force 6 Round Burst CO2 BB Rifle
• Umarex Steel Storm 6 Round Burst CO2 BB Gun
• Umarex H&K MP5K-PDW CO2 BB Rifle
• Beretta PX4 Storm CO2 Blowback Pellet / BB Pistol
• Desert Eagle Black Magnum Research CO2 Blowback Pellet Pistol
• Umarex Browning Buck Mark URX .177 Break Barrel Pellet Pistol
• Beretta FS M84 Blowback CO2 BB Pistol
• Colt Python 6 Inch CO2 Steel BB Revolver
• Colt Commander 1911 Blowback CO2 BB Pistol
• Umarex Legends Luger P08 CO2 BB Pistol
• Walther PPS CO2 Blowback BB Pistol
• Umarex Legends C96 Blowback CO2 BB Pistol
• Legends Makarov Ultra Blowback CO2 BB Pistol
• Umarex HPP Blowback CO2 BB Pistol
• Umarex Walther P38 Blowback CO2 BB Pistol
• Walther CP99 Compact Black Blowback CO2 BB Pistol
• Walther PPK CO2 BB Blowback Pistol 

A very common occurrence with CO2 Airguns and Airsoft guns are leaky CO2 seals. Usually this occurs right where the CO2 cartridge connects to the main valve area. This can be either in the gun or in the magazine depending on the setup of the airgun.

There are many reasons why this can happen, but the most common reasons are a worn-out or dried up seals or even a seal that has been imprinted or misshapen from the constant pressure of the tip of the CO2 pressing against it.

When this happens you may encounter a leaking CO2, the severity of the leak can vary from mild slow leaks to leaks that can be so bad that the gun is unusable. Keep in mind there can be other problems not related to the CO2 seal such as in the valve area, the fix I show you in this YouTube video will not fix a leaking valve, you can try using something like Crosman Pellgun oil for a problem like that.

Watch my below Vimeo video where I show you how you can easily use some Plumbers Teflon Tape to improve the contact points between your CO2 and CO2 main seal and eliminate leaking CO2 in your Airgun.

A very common question I get asked is "How Long Can I Leave CO2 in My Airgun?" So what do I do when I get asked a question over and over again... Well I make a video and give you my answer to the question.

Some CO2 Related Questions I seem to get over and over again are:

1. Can I leave an unused CO2 in my Airgun and for how long is it safe?

2. Can I reuse a C2 once it is empty?

3. Can I use my gun without CO2?

In this YouTube video I address questions 1 and 2, I kind of forgot about question number 3 since it is not as often but it does come up from time to time believe it or not and the answer to being able to use a CO2 airgunwith out CO2 is "NO", It's kind of like trying to drive a car without gas, or turn on a light without electricity or stay alive without food...

So anyways, watch my below Vimeo video for answers to questions one and two:

We have just added the Swiss Arms 4 inch & 6 inch Full Metal Revolvers to the US Store, these are basically teh KWC made guns licensed through Cybergun with the Swiss Arms licensing so you can check out my Umarex Colt Python 357 since it too is the same base gun made by  KWC.

Here are the specs for these Shell loading 357 styled CO2 4.5mm BB Revolvers.

6 Inch Barrel Length Model

• FPS: 410
• Mag Capacity: 6 rounds
• Power CO2
• Length: 11.42 inches
• Weight: 2.67 lbs
• Full Metal, Rubberized Plastic, Textured Grips
• Rotating Cylinder, Manual Safety, Working Ejector Rod
• Single & Double Action
• Includes: 1 Gun, 6 Realistic Shells, 1 Speed Loader

4 Inch Barrel Length Model

• FPS: 344
• Mag Capacity: 6 rounds
• Power CO2
• Length: 9.44 inches
• Weight: 2.39 lbs
• Full Metal, Rubberized Plastic, Textured Grips
• Rotating Cylinder, Manual Safety, Working Ejector Rod
• Single & Double Action
• Includes: 1 Gun, 6 Realistic Shells, 1 Speed Loader

First off, make sure to checkout my Table Top Review for the Umarex Colt Python 357 CO2 BB Revolver so you can get the specs and details on this fine shell loading BB pistol.

In this Field Test Shooting Video I do my traditional Chronograph test where I shoot a series of 4.5mm Steel BB's using a brand new CO2 cartridge to see what kind of real word Feet Per Second performance I can get out of the Umarex Colt Python. On this day I averages right around 390 fps which was very close to the claimed 360 fps form Umarex. The temperature was right around 24 Celsius or 75 Fahrenheit so it was neither cold or hot.

Moving on with the Accuracy Shooting Test, I set myself up 30 feet away using a semi-rested stance (Sand bag up front, standing in the back) I got one of my best ever 6 shot groups from the Umarex Colt 357, coming in at just under 1 inch. During my previous pretest, the Umarex Revolver did well but seemed to spread out a bit vertically, this may have been due to the plastic tips on the shells needing to break in for a more consistent BB fit.

The Umarex Colt Python 357 has taken it up a notch by adding just a bit more overall weight than most comparable shell loading BB revolvers, a smother trigger and hammer mechanism and styling this revolver on the Classic Colt Python platform. If you're a revolver fan, make sure to grab one of these and if you're not a revolver fan, this pistol may just change your mind :)

 Buy the Umarex Colt Python 357 in Canada

Buy the Umarex Colt Python 357 in the US

• Watch my official Field Test Shooting Video for the Umarex Colt Python 357.

Type: BB air revolver.

Manufacturer:UmarexUSA.

Model: Colt Python 357.

Materials: Mostly metal with some plastic construction.

Weight: 2.75 pounds (1218 grams).

Barrel: 5.5 inches, non-rifled.

Propulsion: 12 gram CO2.

Action: Revolver, single & double actions.

Ammunition Type: 4.5mm steel BB's.

Ammunition Capacity: 6 rounds.

FPS: 400fps.

Trigger Pull: The trigger pull on the Colt Python 357 CO2 BB Revolver is good in both single and double action, even better than the Dan Wesson and S&W 327 TRR8 shell loading revolvers, most likely because the spring tension that pushes the inner barrel to make contact with the cylinder is noticeably lighter on the Umarex Colt Python 357. Even the hammer is smoother and has less wiggle, just a better trigger and hammer mechanism overall.

Accuracy: The results I got shooting my 6 round group from a 30 foot out semi rested position where good overall. Vertically there was about a 2 inch spread while horizontally there was about a 1 inch spread. I did find the plastic tips on the brass shells seemed to be a bit tight at first and this is when I did most of my Chronograph and target shooting. I believe the tightness effected the consistency of the FPS which also effected the accuracy especially up and down. I did get one shot out of the Umarex Colt Python 357 well over the claimed 400 fps but again the fps was rather erratic most likely because of the snug BB fit due to shell break-in.

Build Quality: The Umarex Colt Python 357 being mostly metal, you would expect it to have a decent build quality and I am happy to say it does, perhaps again even better than the Dan Wesson and S&W 327 TRR8 shell loading revolvers, even the weight of the Colt Python came in close to a half of a pound more! The only real plastic I could find was in the grips and the shell tips. Fit and finish was also good with no noticeable paint wear or sloppy workmanship.

Realism: The Colt Python 357 CO2 BB Revolver overall is a close copy of the real steel Colt Python 357. I did notice the rear portion of the receiver (between the rear cylinder and hammer) to be a bit longer perhaps to accommodate the CO2 valve length, but other than that this pistol is super close to the original revolver it is based and licensed on. Agin being all metal gives this CO2 BB revolver very realistic weight and feel and the loadable brass shells make using this gun almost exactly like using a real shell loading revolver but for much less cost per shot and of course a lot less recoil on the hands.

Available in the: Replica Airguns Store

Pros:

• It's a revolver with actual shells! Give you the feeling of loading and shooting a real revolver.

• Mostly all metal design.

• lots of detail, well made, fit and finish is very good.

• Good overall weight, heaviest out of all the shell loaders.

• Good overall power, accuracy and shots per CO2.

• Fully adjustable sights for windage and elevation.

• Well hidden CO2 Screw.

• Recessed barrel.

• Nice easy Trigger pull in both single and double action.

Cons:

• Grips are a bit rough.

• All black sights not great on dark backgrounds.

• FPS seemed to fluctuate a bit 

Comments:

The ASG Dan Wesson shell loading revolvers reintroduced me to the joy of loading and shooting a revolver which up until that point was not that realistic of an experience when using a BB or Pellet revolver. The Umarex Colt Python 357 has taken it up a notch by adding just a bit more overall weight, a smother trigger and hammer mechanism and styling this revolver on the Classic Colt Python platform. And all of this for even less than the cost of the original Dan Wesson shell loading series CO2 BB revolvers. If you're a revolver fan, make sure to grab one of these and if you're not a revolver fan, this pistol may just change your mind :)

My Vimeo Table Top Review for the Umarex Colt Python 357 CO2 BB Revolver:

Buy the Umarex Colt Python 357 in Canada

Buy the Umarex Colt Python 357 in the US

In this Vimeo Update Video Preview I show you around two brand new Umarex CO2 BB pistols, the Umarex Walther PPS and the Umarex Colt Python 357, both recently added to our online Replica Airguns Store.

The Umarex Walther PPS is a full licensed CO2 BB Blowback replica of the real steel super compact Walther PPS and it compares well to the ASG Bersa BP9CC that I reviewed earlier and by the way ended up being one of my favorite compact air pistols. That said I think the Umarex Walther PPS is the new king! It is even more compact yet has great fps for a super small CO2 pistol, shot very accurate even from 30 feet out and has more blowback recoil than the larger Bersa BP9CC!

Here are some of the specifications for the Walther PPS CO2 Blowback 4.5mm BB Pistol:

• Velocity: 350 fps

• Length: 6.4”

• Barrel Length: 3”

• Weight: 1.2lbs

• Magazine Capacity: 18 Rounds

• Power: 12 gram CO2

• Ammo: 4.5mm Steel BB

• Material: Metal and Plastic

• Action: Blowback Single Action Only

Umarex added another shell loading revolver to their collection, the fully licensed Colt Python 357 and again this revolver uses CO2 and shoots 4.5mm Steel BB's that are preloaded into 6 included brass shells. Out of all the 4.5mm shell loading revolvers to date, I have to say the Colt Python 357 is the heaviest coming in at just under 3 pounds. The trigger hammer combination is also very smooth and it has a fully adjustable rear sight for windage and elevation.

Here are some of the specifications for the Colt Python 357 4.5mm BB Revolver:

• Velocity: 400 fps

• Length: 11.75”

• Barrel Length: 5.5”

• Weight: 2.75lbs

• Magazine Capacity: 6 Rounds

• Power: 12 gram CO2

• Ammo: 4.5mm Steel BB

• Material: Almost all Metal

• Action: Single and Double Action

Watch my Vimeo Preview Video of the Umarex Walther PPS and Colt Python 357 BB Pistols:

Buy the Umarex Walther PPS in Canada

Buy the Umarex Walther PPS in the US

Buy the Umarex Colt Python 357 in Canada

Buy the Umarex Colt Python 357 in the US

This may be a bit controversial for some people who don't like the thought of using an gun for hunting or extermination of unwanted pests. But weather or not it is accepted by all, it is a practice that many people still embrace including myself when done in a humane way.

Let's start off by addressing this topic by asking some questions and filling in some of the answers. Keep in mind I go into much more detail in my Vimeo video below.

What is the reason that you need to Shoot or Hunt an Animal?

Are you shooting an animal out of need or just for fun, sure there is a thrill in the sport of hunting but after taking down your prey, the animal should not be killed in vain as the meat should be eaten. There are also times when pesky critters get into your gardens, tree farms, feeding stations garbages and who knows what else? I personally think shooting an animal that has not done you any harm or that you don't plan on eating is not ethical. So question your motives wisely?

Can you use an Airgun for Hunting and or Pest Control?

The short answer is yes! As long as you choose the correct Airgun for the job, one that has enough power and accuracy to get the job done in a humane manner. Using an underpowered or inaccurate gun of any type for the chosen target will lead to the animal being wounded and possibly getting away to suffer unnecessarily.

What about Pistols versus Rifles?

Given the choice, a rifle will always be your best bet, rifles tend to be more accurate since they are more stable to hold and the fact that the sights are further apart which improves the guns accuracy. Most rifles also allow for enhanced sighting systems like red dots or magnified scopes for even further accuracy improvements. There are some pistols made specifically for hunting and target shooting that can be accurate but I would limit their use to shorter ranges.

What about Pellet guns versus BB guns?

BB guns in general are not meant for hunting or pest control, and in most cases they are underpowered and not as accurate as their pellet shooting counterparts, especially out at longer ranges where most pests keep their distances to. If you plan on doing some hunting and or pest control, please invest in an adequate pellet rifle to get the job done humanly.

What type of Ammo is best for Hunting and Pest Control?

There are lots of types of pellets available, pointed, rounded, flat, hollow-point and even pellets that have nylon tips. At the end of the day, use the pellet that is the most accurate in your Airgun because shot placement will win over pellet shape any day of the week. The reality is that as long as that pellet hits the target with adequate velocity, it doesn't matter what shape it is, it's more than likely going to pass right through the animal.

What is the lowest FPS that I can use?

I would rather ask the question, what is the highest fps I can get away with since more fps will give you more margin for error, since it will have a flatter trajectory and will do more damage even if your shot is off a bit. An experienced shooter could make a kill shot on a small pest even with a 400 fps airgun but the shot would have to be perfect and the range would have to be close. Of course when shooting larger game, you will need larger caliber pellets with higher velocities. Also when using a high velocity airgun you need to consider what is beyond your target, if you miss, where is that pellet or bullet going to end up? You need to make sure you do not injure anyone by mistake as pellets/bullets can travel a long distance.

How large of an Animal can an Airguns Kill?

This is really dependent on the Airgun being used, Airguns come in many different calibers, from .177 right up to .50 caliber, some PCP Airguns can even take down a deer! You need to do your research and make sure the Airgun you choose has both the power and accuracy you need for the intend prey.

Where can I use an Airgun for Hunting and or Pest Control?

This is a question you need to ask your local authorities as laws and hunting regulations are different just about everywhere. Even shooting pests on your property may require a permit so be careful to obey your local laws.

In this Comparison Video I go through the benefits and shortcomings of CO2, Spring Piston and Pump Airguns. I focus mainly on Airguns but there is a bit of a crossover with Airsoft guns.

All three systems (CO2, Spring, Pump) create pressure that forces the ammunition with a high force out of the barrel. Similar to how gun powder is the source of energy for a bullet.

Here are some basic statements that best describe CO2, Spring Piston and Pump Airguns.

CO2 Airguns:

• CO2 Airguns use the expansion of CO2 gas to create the pressure required for the ammo.

• CO2 Airguns generally store enough CO2 for multiple shots per cartridge.

• CO2 Airguns have a limit as to how much power they can produce since CO2 has a set vapor pressure of 850 psi, or about 56 bar at room temperature which is around 25 C or 77 F. CO2 Gas also requires a warm environment to expand so warmer temperature and longer barrels help with power.

• Some CO2 guns can also use pressurized air tanks in place of CO2.

Spring Piston Airguns:

• Spring Airguns use the release of a pre-cocked spring and plunger system to compress air to power the ammo.

• Spring Piston Airguns require the cocking of the spring between each shot so they are single shot only.

• Spring Airguns are limited to how much effort is humanly possible to cock the spring into position. If you make the spring to strong then not everyone will be able to use the Airgun effectively. Too week of a spring and the Airgun will lack power.

• Spring Piston Airguns are known for having a fair amount of recoil and vibration when the spring moves both forward and backwards quickly inside the Airgun.

• Spring Airguns can use either a mechanical spring or a gas spring.

Pump Airguns:

• Pump Airguns (either Single or Multi-Pump) store air pressure in a chamber that when released, powers the ammo.

• Most Pump Airguns require at least 1 or more pumps, often up to 10 pumps for each shot and you generally only get one shot per set of pumps. Not to be confused with PCP Airguns (Pre Charged Pneumatic) which have large pressure tanks that are recharged with a high volume of pressurized air that is capable of shooting multiple shots per charge.

• Pump Airguns are also somewhat limited to how much effort is humanly possible since the higher the chamber pressure, the harder it will be to pump the Airgun. 

Misc Airguns:

• Generally speaking both Spring and Multi-Pump Airguns have more potential power than a CO2 guns since CO2 has a set peek pressure limit.

• Pump and CO2 Airguns are know to have very little recoil since the pressure is stored in a chamber and then released by a valve. No slapping back and forth of a large internal spring.

Pros:

CO2 Airguns:

• CO2 Airguns allow for multiple shots per CO2 cartridge for more realistic action shooting.

• CO2 Airguns do not require any human effort to charge the gun other than loading the CO2 and Ammo into the Airgun.

• CO2 Airguns allow for true semi auto shooting ability. 

Spring Piston Airguns:

• Spring Airguns have the potential for high velocity since the larger and stiffer the spring, the greater the output force.

• Spring Airguns do not require anything other than your ammunition, typically either a Pellet or BB.

• Spring Airguns are mechanically very simple which makes them very reliable and less expensive to produce than other types of Airguns. 

Pump Airguns:

• Pump Airguns have the potential for high velocity since more pumps equals greater output force, only limited by the users strength and the pressure rating of the Airgun.

• Pump Airguns do not require anything other than your ammunition, typically either a Pellet or BB.

• Pump Airguns have next to no recoil which makes them very easy to shoot and highly accurate.

Cons:

CO2 Airguns:

• CO2 Airguns require the purchase and use of CO2 or they simple do not work.

• CO2 Airguns are very susceptible to temperature changes, especially cold temperature since CO2 needs a warm environment in order to expand. Cool down effect also plays a role in power output.

• CO2 Airguns have a maximum set amount of power output.

Spring Piston Airguns:

• Spring Airguns require the pre-cocking of the spring for each shot.

• Spring Airguns can take some getting used to since the spring recoil/vibration requires a very lose grip (Military Grip) to shoot accurately with them.

• Spring Airguns should not be stored pre-cocked since this can damage the spring, less so with gas spring versions. 

Pump Airguns:

• Pump Airguns require pre-pumping to pressurize the air chamber for each shot.

• Pump Airguns, especially Multi-Pump Airguns take the most amount of human effort for each shot.

• Pump Airguns need to stored with at least one pump in them or the seals can get damaged over time.

In this Comparison video I go through the benefits and shortcomings of both Blowback and Non-Blowback Airguns. I focus mainly on Airguns but there is a definite crossover with Airsoft guns.

Here are some basic statements that best describe both Blowback and Non-Blowback Airguns.

Blowback Airguns:

• Blowback Airguns usually have a movable slide that moves back and forth with each shot.

• Sometimes the blowback operation is internal (Internal bolt) so there may not be an external moveable slide.

• Some CO2 is used to move the slide rearwards in a Blowback Airgun.

• The Blowback motion of the slide with some blowback airguns can also cock the hammer or internal striker allowing for true single action trigger pull. But not always!

• Some Blowback airguns have the potential for full auto capabilities since they can have a true semi auto action.

• There is some noticeable recoil from the Blowback action simulating the recoil of a real gun.

Non-Blowback Airguns:

• Non-Blowback Airguns can have fixed or movable slides but they will not cycle back and forth with each shot.

• Non-Blowback Airguns tend to have less working parts since no Blowback valves are required or even a moveable slide.

• There are some Blowback and Non-Blowback Airguns that field strip similarly to their real steel counterparts but this is most commonly found in Blowback Airguns.

• Non-Blowback Airguns require the shooter to cock the hammer for single action shooting or use a double action trigger pull for semi auto like performance.

Pros:

Blowback Airguns:

• Blowback Action causes a noticeable recoil which makes the airgun feel more realistic.

• Blowback Airguns in some cases have true semi auto action with true single action triggers which mimic the authenticity of the real steel versions of the guns they replicate much better making them better training tools.

• Having some recoil makes blowback Airguns potentially better training tools.

• Blowback Airguns look really cool when shooting them  and are great action prop guns.

Non-Blowback Airguns:

• Non-Blowback Airguns tend to have less working parts so less to go wrong and more reliability.

• Non-Blowback Airguns can be more accurate since the recoil from the blowback is not a factor.

• Non-Blowback Airguns have more potential power and more shots per CO2 since no CO2 is robbed for the blowback operation.

Cons:

Blowback Airguns:

• Blowback operation can rob some of the power and will also rob how many shots you get from the Airgun.

• Blowback Airguns are effected even more by cold weather and the cool down effect.

• The recoil from Blowback Airguns can effect accuracy for some shooters.

Non-Blowback Airguns:

• Non-Blowback airguns are generally double action when shooting semi auto and so the trigger pull will be longer and heavier.

• Non-Blowback Airguns do not replicate the recoil action of a real gun.

• Non-Blowback Airguns do not look as cool to shoot and are not as good of an action prop gun.

Is an Airgun Good for Self Defense? Another one of those questions I get asked fairly often that's a bit hard to answer in a few sentences... Not all of us have easy access to a 9mm pistol or even a rifle but many of us can get our hands on an airgun fairly easily and they look real enough, I guess that is one thing they have going for them.

But what if the mere sight of what looks like a gun does not scare an intruder off? If you where hoping that would be enough, you may just be out of luck and what if you just brought an Airgun to a "real" gun fight? You are going to be drastically "outgunned" pun intended and here's why. A 4.5mm Steel BB weighs about 5.1 grains and generally you are looking at about 2-3 foot pounds of energy from a CO2 BB gun. Even a .177 caliber lead pellet is only marginally heavier at around 7-8 grains and if you're really lucky you might just get 4 foot pounds of energy out of a CO2 pellet pistol.

So let's take a look at a fairly conservative "real pistol" rounds, the 9mm. The 9mm rounds come in different bullet weighs but you can get a 120 grain 9mm in a plus p ammo with as much as 400 foot pounds of energy and even with that much raw power, many people claim that a 9mm round does not always have enough stopping power to put down a person even when shot multiple times center mass. It just depends what vital organs or arteries you hit that determines if he gets lucky or you get lucky.

Your 5.1 grain 4.5mm Steel BB is not going to do anything if it hits any type of clothing and even if you find some flesh it's just going to piss off the intruder.

My suggestion is to consider a bat or a golf club or a really big knife or just about anything other than an airgun because if the sight of the airgun replica does not scare an intrude away then you are really buggered.

Keep in mind that you need to abide by any laws regarding the use of self defense in your areas. Even just physical force could be considered a crime and at the end of the day you are ultimately accountable for your actions.

I finally answer the question... Which Airgun is the Best? There has to be a best airgun out there right? So let's cut to the chase and stop waisting everyones time and money buying the third Best Airgun or even the second best Airgun! Why would you even want anything other than the very best Airgun available to mankind!

I really hope you weren't one of the gullible ones that actually bought something other than the Best Airgun, well I guess you're going to have to watch my YouTube video to find out which Airgun is the Best Airgun of all time...

In many of my reviews I show the loading process of each gun but sometimes I either skim over this part or assume most people already know how to load an Air Pistol and skip it entirely. Well as it turns out not everybody does know how to load up an Airgun or they are unclear on certain areas, like do you actually need the CO2 and how long can you leave CO2 in an airgun?

So I made a video specifically to cover how to load CO2, BB's and/or Pellets into your Air Pistol.

Now even though this video is targeted at 4.5mm Steel BB and Lead Pellet Pistols, there is a crossover with 6mm Airsoft Pistols so this video may also help an Airsoft shooter.

Our Family Bearded Dragon (Dijon) was looking rather sad and lonely today so I figured he could hang out while I made the video, he really doesn't do much of anything most of the time so why not give him a special appearance in one of the Replica Airguns Videos ;)

Two questions that come up over and over again and to be honest I just hate answering, mainly because both of these questions to me are kind of common sense questions. I feel if someone where to stop and actually think about teh question, the answers would become obvious.

That said, common sense has to be learned somewhere and not all of us are exposed to the same life experiences so here goes...

The two questions are:

• Will this Ammunition Work in my Gun?

• Can I Convert a Blank Gun to a Real Gun?

The answer for both of these question is actually the same! Use the ammo made for your gun and do not try to use anything other than the ammo that was made for your gun. Do not try to modify your gun to shoot anything other than the ammo that was made for it, if you do, you may be breaking the law and could land yourself in jail. If you can follow these rules then your ammo and gun will work as intended :)

So that's pretty much it in a nutshell, watch my YouTube video below as I show you examples of ammo types with visuals on exactly why you need to use the ammo made for your gun. I also talk about the dangers of attempting to modify a blank gun to shoot some sort of real bullet and why it is a very bad idea in so many ways to try and convert a blank gun into a real gun.

Buy the ROHM RG-88 9mm P.A.K. Blank Pistol in the Canada Store

Buy the ROHM RG-88 9mm P.A.K. Blank Pistol in the US Store

This video should go "Hand in Hand" (pun intended) with my Best Two Handed Pistol Grip Tutorial Video that I did last year back in August. After that video I had several people ask me to talk about how to aim a gun. I guess if you have been shooting guns for a while you kind of take it all for granted but after teaching my kids the proper way to aim a gun at a target, this info is not naturally born into us ;)

This video demonstrate how and where to place your open gun sights on a target and also how you can compensate for a gun that may not be perfectly sighted in.