Yes, I have more of my personal guns for sale, now we are getting into the pistols! I am showcasing here on the Replica Airguns website and over on the Replica Airguns YouTube channel a series of videos I am making for the purpose of selling some guns out of my personal collection. I simply have to make room for the new guns I will be testing and reviewing for everyone, my collection has gotten a little bit out of hand and needs to be thinned down a bit :)
In this 5th Mike's Personal Guns For Sale video, I am offering some of my pellet pistols in a variety of models ranging from some classic Crosman SAA .22 caliber revolvers to more modern CO2 blowback pistols like the Umarex Beretta PX4 Storm
Make sure to watch my above YouTube video to see these Pellet Pistols I am selling and instructions on how you can take part in the sale and purchase of them. By the way I am only selling to Canadian residents since shipping cross borders is a little sketchy.
Here is a list of the Pellet Pistols I am selling from my personal gun collection:
Trigger Pull: The ASG Dan Wesson 357 Revolver has a smoother trigger than the previous non 715 Dan Wesson Revolvers. There seems to be less of that friction while the cylinder rotates past the spring engaged inner barrel. Even the Hammer has a nicer fell to it with less side to side wiggle. Single action is really nice with a very short take up and light release point.
Accuracy: I have not had a chance to test out the ASG Dan Wesson 715 6 Inch Silver CO2 BB Revolver so far since the outside whether has been rather cold and wet. In terms of accuracy I would expect at least a 1-2 inch grouping from 30 feet out and the clamed fps of 430 seems to be in line with what we should see from the 4.5mm BB shooting Dan Wesson 715. I guess we will have to find out later on when I do my Field Test Shooting video to be sure...
Build Quality: I thought the previous generation Dan Wesson Revolvers where built really nice but the new Dan Wesson 715 takes this up several notches higher. All you need to do is pick this gun up and immediately you are in a state of wow! You almost need to ask yourself if it is in fact the Real Steal Dan Wesson 715 357 Magnum Revolver it feels that good. ASG has beefed up the barrel assembly to a solid component that adds a lot of forward weight which would be just like what you would expect from the 357 Magnum shooting version. To balance it all off the forward weight, the grips section is also reinforced with metal underneath the Hogue Styled rubber finger grips which again are another huge improvement over the plastic pistol grips found on previous models of the ASG Dan Wesson's. The stainless finish is of course awesome and this guns simply looks and feels great!
Realism: Again referencing the new ASG Dan Wesson 715 6 Inch Silver CO2 BB Revolver to it's predecessors, the Dan Wesson 715 is a true replica of the Dan Wesson 715 357 Magnum Revolver in almost every aspect and not just the Dan Wesson name. I could tell you everything that was the same but it's simply much easier to point out the only real difference I was able to point out and that would be the two pins that connect the barrel assembly to the frame of the BB version of the Dan Wesson 715. Not a deal breaker by any means and the pins really don't take away from this gun in my opinion.
Another great shell loading revolver, perhaps one of the nicest modern BB revolvers to date!
Almost all metal design, super heavy, feels like a real gun in the hand.
Lots of detail in this gun, very well made, fit and finish is excellent.
Dan Wesson Licensed and an excellent replica overall.
Adjustable rear sight for windage and elevation.
Rubber Hogue style finger grips, huge improvement over previous Dan Wesson grips.
Well hidden CO2 screw and Allen key built into the removable grip.
Much improved hammer and trigger action, smoother trigger and less wiggle in hammer.
Barrel opening is very realistic, even has simulated rifling.
Safety design is well hidden and easy to use.
Cons:
Two pins to attach the barrel assembly to the frame are not in line with the real steel version.
Trigger still has a bit of that initial friction in double action mode because of the spring loaded internal barrel.
Comments:
I was already a big fan of the Dan Wesson line of Revolvers, this new 715 version of the Dan Wesson takes it to a whole new level! In terms of the modern shell loading CO2 Revolvers out there the ASG Dan Wesson 715 6 Inch Silver CO2 BB Revolver is by far my new favorite. ASG completely redesign their new ASG Dan Wesson 715 6 Inch Silver CO2 BB Revolver basing it entirely on the real steel version and capturing the quality, look and feel nearly exactly. if you already have a Dan Wesson Revolver and think that perhaps you can pass the new version by, well I would think again or you may be missing out on one of the best BB Revolvers out there at this time.
My Vimeo Video Table Top Review for the Dan Wesson 715 CO2 BB Revolver:
I will be showcasing here on the Replica Airguns website and over on the Replica Airguns YouTube channel a series of videos I will be making for the purpose of selling some guns out of my personal collection. I simply have no more room for the new guns and in some cases I either have duplicate guns or very similar versions so there is no need to have both. Some guns I am less attached to and as I already stated I need to make room for some of the new stuff I will be reviewing.
To start this series off my first video is to highlight the blank guns I am selling, there are only 4 of them, all of which are really hard to get here in Canada so I am not going to let them go cheap. By the way I am only selling to Canadian residents since shipping cross borders is a little sketchy.
Make sure to watch my above YouTube video to see the blank guns I am selling and instructions on how you can take part in the sale and purchase of them.
Here is a list of the blank guns I am selling from my personal gun collection:
Another preview video with some pistols from Umarex, ASG and Gletcher. Two of these Airguns I got to see whiel I wa sin SHOT Show this year so it was nice to be able to spend a bit more time with each one now that I have them in person for review :)
Lets start off with the ASG Dan Wesson 715, mine happens to be the Stainless version in 4.5mm Steel BB. What an upgrade over the original Dan Wesson Revolver and I thought those where already really good! The all new ASG Dan Wesson 715 is super solid coming in close to three pounds with its mostly solid metal construction.
Next up is the Umarex Combat Vet 1911 which is essentially a KWC 1911 distributed and Colt licensed via Umarex. The Umarex Combat Vet 1911 is a limited edition product made to look weathered and used and it does look amazing!
Lastly the Gletcher Stechkin in a Gold finish shipped in a real wood box with velvet lining. This is the same Airgun as the Gletcher APS but blinged out a bit, the Gold finish is lined with black etching to really make this gun look unique.
Ammunition Type: 4.5mm steel BB's. or .177 cal. pellets.
Ammunition Capacity: 6 rounds.
FPS: (BB 410) (Pellet 380).
Trigger Pull: Trigger pull on the John Wayne Duke Colt SAA BB and Pellet Revolver is the best I have ever come across in an airgun. Being that these Single Action Army Revolvers are single action only, most of the work is done while you pre-cock the hammer. The trigger pull is under 2 pounds and has virtually no take up with a crisp release. I love the ratcheting sound as you pull back the hammer just like using a real SAA Revolver!
Accuracy: I have not yet tested these John Wayne Duke Colt SAA BB and Pellet Revolvers so far but expect the BB version to perform for the most part just like the Umarex only versions I tested previously. Here are my notes from my previous testing:
"I tested both 4.5mm steel BB's and 4.7mm Lead ball BB's in the Umarex Colt Single Action Army Shell Loading BB Revolver. With the Steel 4.5mm BB's I shot just under a 2 inch 6 shot grouping when shooting from a 30 foot distance using a semi rested position (Sand bag up front, standing in the back). The shots where pretty well center hitting the paper target just a little bit high, they did seem to stray a little more left and right rather then up and down. When I switch ammo to the 4.7mm Lead BB's I got a similar 2 inch grouping but they hit the target a bit lower and tended to shoot tighter from side to side with more variation up and down, perhaps because the lead BB's did not seem to shoot at a vary consistent velocity. My Chronograph testing for the Steel BB's was right around 400 fps while the Lead BB's being heavier shot a bit slower at just under 300 fps."
Build Quality: The John Wayne Duke Colt SAA BB and Pellet Revolvers have a mostly all metal construction other than the plastic grips and any seals. The fit and finish is excellent with a great overall weight in the hand. Whether you get the Nickel or Weathered version. The mechanical action of the hammer and trigger feels just like it would on a real single action army revolver.
Realism: In terms of replicating a real steel Colt Single Action Army Revolver, these guns are absolutely amazing replicas. It's really hard to tell the airgun version from the real steel version, except for the smaller in diameter shells and the discreet safety switch located under the frame. Even the barrel is nicely recessed and has some fake rifling twists in it to give the appearance of a large caliber round. The CO2 is well hidden with the Allen key built into the handle so no ugly CO2 screw tab hanging down.
Still the best airgun reproduction of the Single Action Army Revolver, a very accurate replica of the real steel old west version.
Recessed barrel has the look of a large caliber bullet.
Great weight and feel in the hand.
Shell loading design that loads from the back so no need to remove shells if you wish not to.
Hammer and trigger action is about perfect, no take-up, very crisp and super light (under 2 pounds).
Finish on both the Nickel and Blued is very nice.
Colt and John Wayne Duke licensing.
Very well concealed CO2 with built in Allen key.
Discreet safety location.
If you prefer pellets over steel BB, now you have the option.
Cons:
Still has the warming instruction on the right side of the barrel but not super obvious especially on the Nickel version.
Real version would shoot 45 caliber, dummy shells are actual closer to 357 so a bit smallish.
Wood grips to me look a little fake up close but the John Wayne emblem kind of makes up for it.
Comments:
Shell loading BB and Pellet revolvers have been out for a while now and have changed the way many of us feel about airgun revolvers. Airgun revolvers used to be kind of overlooked because they where not the most exciting replica airguns out there but now we have not only the new Dan Wesson 715 shell loading revolvers but also these Colt Single Action Revolvers with Colt and John Wayne Duke licensing on them available in both BB and pellet shooting versions! There is something special about these old cowboy day classic revolver that makes them so elegant and just a real work of art you can not only own and look at but also take out and shoot whenever the spirit moves you to do so!
My Vimeo Table Top Review for the John Wayne Duke Colt SAA BB and Pellet Revolver:
In this 2016 SHOT Show Interview I talk with Bob Li from Action Sport Games. Bob shows me some of the new products this year from ASG. Some of ASG's newer pistols are the Dan Wesson 715, the CZ 75 SP-01 Shadow, the CZ P-09. New to the rifle line is the CZ Bren 80, also a couple of sniper rifles, the M40A5 and M40A3. ASG is also coming out with a an Inferno HPA version of their CZ Scorpion EVO 3A1.
The ASG Dan Wesson 715 has ot me my favorite product from ASG, you need to hold it in your hand to really understand how solid this pistol really is at close to 3 pounds. Everything about it is an improvement over previous Dan Wesson models including the trigger and hammer action, crane setup and the more actuate frame length with the new more compact internal CO2 valve. The ASG Dan Wesson 715 will be shipping in 4.5mm Steel BB, 6mm Plastic Airsoft and .177 caliber pellet versions.
ASG's two new Full blowback CZ 75 SP-01 Shadow, the CZ P-09 pistols should be coming out shortly, both will be available in 4.5mm Steel BB and 6mm Plastic Airsoft. Both pistols feature a metal slide and frame with full size drop out metal magazines and will have CO2 and Green Gas magazine configurations. The CZ P-09 will have a threaded barrel and barrel protector.
In this 2016 SHOT Show Interview I talk with Nichol Goines from Umarex USA. Nichol and I discuss some new and somewhat revised products from Umarex like the Full Blowback Smith & Wesson M&P40, the soon to finally be released Beretta Model 92 A1, a new Pellet version of last years Colt Single Action Army Revolver and a reappearance and revision of the Walther PPK CO2 Blowback BB pistol.
Last year Umarex introduced their Colt Single Action Army CO2 BB Revolvers and I would say last year they where on of my highlight airguns for the show. They have been selling like gang-busters! One question people have been asking is if there will be a pellet shooting version? Well now there is and like the Steel BB version the pellets load from the back of the shell making it super easy to reload the removable brass shells. The new Pellet SAA Revolver also has a rifled barrel to help with accuracy.
M&
I would have to say this years gun highlight well at least from Umarex is their new Smith & Wesson M&P40 full blowback CO2 BB Pistol. It is a perfect copy of the real steal version complete with a full size drop out magazine and full Beretta licensing. I really hope this one ships soon and does not get delayed like the Beretta Model 92 A1 introduced last year and still yet to be shipped :(
Speaking of the Beretta Model 92 A1 CO2 Blowback BB pistol. It is finally getting released this February and like the S&W M&P40, is a virtual identical replica of the original Beretta Mod. 92 A1 complete with full blowback, a full size drop out magazine and of course all the trades and licensing in all the right locations.
Last and not least but still worth noting is the CO2 Blowback BB shooting Walther PPK. It kind of dropped out of productions which is a real shame since it was the replica BB pistol that got all of this started for me several years back and to this day is still a lot of fun ot shoot! Even James Bond went back to the PPK for the latest 007 movie! Well it's back and this time Umarex got rid of the ugly CO2 tab and replaced it with a discreet Allen key screw. Saves us all from doing the CO2 screw mod :)
This is my SHOT Show 2016 Teaser Video! You will get to see some new gun highlights from companies like Umarex, ASG, Crosman, Sig Sauer, KWA and ISC. I will be following up this video with some interview videos very soon so do make sure to check back for those uploads. All I can say about the show is it’s huge! So much to see, so much walking and too much to take in…
ASG:
As always, ASG had some new products this year. The all new Dan Wesson 715 357 Magnum shell loading Revolver! This gun feels absolutely amazing in the hand and will be available in Steel BB, Airsfot and even Pellet shooting versions. Also new are the CZ P-09 and CZ 75 SP-01 Shadow Full Blowback BB and Airsoft Pistols.
Crosman:
Big at Crosman this year was their PCP Airbow, Crosman put a lot of focus on this product and even had a lot of crossbows on display to go with their new PCP Airbow. Crosman also introduced their low cost entry level Benjamin Maximus PCP rifle in .177 and .22 calibers offerings. Not really much in the way of replica pistols from Crosman this year, but then again last year was kind of the same?
Sig Sauer:
I finally made it to the Sig Sauer Booth this year to checkout their new CO2 Pellet gun line. All new Sig Airguns are made true to size and weight with similar trigger actions as their real steel versions. The Sig MPX is their more compact (shorter barreled) pellet shooting CO2 rifle with internal blowback and belt fed 30 round magazine. The Sig MCX is the longer barreled rifle version but built much the same as the MPX. Sig also introduced two new pellet shooting CO2 Blowback Pistols, the P226 and the P250. Both use similar double ended rotary magazines as the Umarex PX4.
Umarex:
Umarex always seems to have some new exciting Airguns products to offer at SHOT Show. The PPK is back with a few updates including no more ugly CO2 tab sticking out of the bottom! And yes the Beretta Model 92A1 will finally be shipping soon, I believe in February! My favorite product this year from Umarex would have to be the Full Blowback, Full size drop out magazine S&W M&P 40 CO2 BB Pistol. Umarex released yet another 1911 on the market, this version does come with a stick mag and sports pretty high fps and more shots per CO2 then the KWC based 1911’s. The super popular Colt SAA Revolver is now available in a pellet shooting version with a rifled barrel :) Umarex had on display another low cost revolver, the ultra futuristic looking Brodax CO2 BB Revolver.
KWA:
KWA always has really nice high quality products to showoff at there booth each year, we may even start carrying some of KWA's products this year, fingers crossed on that one… New to the KWA line are some AEG rifles with simulated blowback action, I really liked the Blowback AEG AK they had on display. KWA also released a new Airsoft shell loading revolvers that had some of the nicest looking brass and aluminum shells. On display under a glass cover was a very solid Gas Blowback Thompson Machine-gun with real wood stock, it was absolutely gorgeous!
ISC:
ISC known for their top quality AEG internals, had their full line of high quality Airsoft rifles on display. And new this year to ICS was their first ever Airsoft pistol, the blowback BLE Alpha. The BLE should be out mid year and looked and felt really nice. The trigger on it was super short and light.
I have some really awesome Interview videos I’m working on, I will be uploading them shortly so stay tuned for those…
I just got some really interesting new guns and shooting accessories I wanted to share with everyone in this Vimeo Video Preview!
First off, I have some metal targets designed for Airguns, you can shoot them with lead pellets and heavy gram Airsoft BB's but be sure not use standard 4.5mm steel BB's as they can ricochet and come back at you at high velocity. That is unless you are using the new Excite Low Ricochet Smart Shot BB's I also showcase in this video.
A couple other accessories I highlight are a Western Leather Gun Slinger Belt and Holster which pair up perfectly with the first BB gun I have to show you today. Most of you should be familiar with the Umarex Colt Single Action Army Revolvers I have made several reviews and videos for, they are super popular and for good reason. How about a John Wayne Duke Version available in Stainless and Antique versions? I thought you would like that!
Next up and probably the item I am most excited to introduce to everyone is the ISSC M22 4.5mm CO2 BB Pistol. I actually own the first generation ISSC M22 in 22LR, the same gun this BB pistol is based on. It seems to have everything going for it and I was happy to discover after making this video that it does in fact have blowback operation even though this is not state on the box or in the manual? The ISSC M22 really is a beautiful pistol and I am totally looking forward to reviewing it. If you're a Glock fan this is about as close as we can legally get to owning a replica Glock BB pistol since Glock has OK'd production of the real steel ISSC MK22 in its new form.
I will be working with my suppliers to make these items available in our Replica Airguns Stores as soon as we can...
When I say Airguns, I am referring to pretty much all BB, Airsoft, Pellet, Paintball and even Blank guns for most of the topics listed here.
Do’s:
Treat your Airgun just like you would a real gun. If something goes wrong, perhaps the outcome will not be as severe but do you really want to take a trip down to your local emergency ward to get a BB or Pellet removed?
Always assume your airgun is loaded, for some reason it always seems those empty guns are the ones that do the most damage.
Be discrete, If it looks like a gun other people will think it is a gun so don’t flash your airguns around in public. Keep it in a case when transporting and shoot it in an area that will not alarm other people.
Always wear eye protection when shooting your Airgun. Do you really want to shoot your eye out? No Joke!
Be aware of your surroundings like windows, hard objects that could make your ammo bounce back at you. Make sure you are shooting your Airgun in a safe direction at all times, know your target and beyond.
Use Airguns to teach others and learn how to safely and effectively shoot a gun. Airguns can be less intimidating then a real gun (Not so loud and very little recoil) and make for great start out and transitions guns.
Use Airguns to get more inexpensive trigger time and become a more experienced shooter. Airguns cosy only pennies per round to shoot and can be shot in way more areas than a real gun can, practice makes perfect so get shooting!
Use Airguns in areas where real guns may not be allowed or safe to use. Again, Airguns can be shot in all kinds of places, in your back yard or even in a properly setup indoor home range.
Use Airguns with adequate power for safe and humane pest control where real guns may be prohibited.Airguns are quiet and less likely for the bullet to travel long ranges which makes them ideal for close range pest control in areas where real guns are too loud and to powerful.
Don’ts:
Do not assume because it is an airgun it is not dangerous or simply a toy. Many Deaths have been caused by Airguns along with a lot of pain and suffering so treat your Airgun with respect. It is not a toy or you would find them in the toy department at your local store along with yo-yos and stuffed animals.
Do not point or shoot at people unless of course you are using an Airsoft gun in an Airsoft field or facility. Yes Airsoft guns are meant to shoot at each other (with appropriate attire like eye protection and full body clothing), but steel BB and Pellet can cause serious injury especially at close range and on direct skin contact.
Do not leave your Airgun loaded, you never know who is going to come across it and accidentally discharge it. Remember, a loaded gun is a dangerous gun in the wrong hands. You may know better than to assume the gun is undulated but children and even adults without any gun training will most definitely handle the airgun without consideration of the danger it poses.
Do not use an Airgun for self protection. See my related video. Simply put, Airguns are not practical for self defense because they rarely have enough Stopping Power. The ones that do have enough power need to be pre-charged and in most cases are only single shot meaning if you miss or don’t get the job done no the first shot then you are done.
Do not use an underpowered Airgun for pest control. See related video. Using a low powered BB pistol for pest control is cruel, you will only injure the animal making it suffer unnecessarily. Use a high powered pellet rifle to get the job done.
Do not take your gun apart, in most cases this will void the warranty and the reality is that airguns rarely need to be cleaned since no dirty gun powder is used. lead pellet rifles may require occasional barrel cleaning to keep the rifled barrel free of debris.
Do not over oil your Airgun, a little goes a long way and too much oil will just attracted dirt, use the right airgun oil and just enough to keep part functioning smoothly.
Do not over pump an Airgun. Over pumping an Airgun can cause damage to valves and seals and in a worse case situation a rupture the air pressure reservoir or even cause the airgun to explode!
Can I use Airsoft BB's in my BB Pistol? I would have to say this is by far the number one question I get asked in the comments section of my Vimeo videos. I have made several videos where this question gets addressed within the video but so far to date I have not made a stand alone video just covering Airsoft BB use in BB Guns.
So here it is, and now I have a video I can link to this so very common question, if you where wondering about this yourself than please watch my YouTube Video on this topic as it goes into a fair amount of detail about it.
The short answer to this question is no, you can not use 6mm Airsoft BB's in a 4.5mm Steel BB Pistol or Rifle. For the simple reason that 6mm is larger than 4.5mm and so the physical diameter of a6mm Plastic Airsoft BB is just to large to fit inside of a 4.5mm Steel BB magazine or barrel.
People have commented about using a 4.5mm plastic Airsoft BB in a 4.5mm BB gun and yes this could in theory be an option but I discuss why I feel this is not a good idea based on size and mass.
In this video I feature my top five favorite BB pistols for early 2016. That said there are lots of other BB pistols I truly love and enjoy but I had to pick 5 so these are them! You may notice that many of them are blowback, I do like the blowback guns after all and this is my top 5 pick so naturally many of them will have blowback action.
Here is a list of my top 5 guns featured in this video not necessarily in order of choice:
I'm getting close to uploading 600 videos now over on the Replica Airguns Vimeo channel, so there are bound to be a lot of similar questions and popular discussions. In this Replica Airguns Vimeo Video I address what I feel are my Top 10 Most Common Airgun Questions and Discussions.
Whether you like it or not, most of us have come across an Airgun with an ugly orange tip on it at some point. In most cases you will find the intrusive orange or red tips on Airsoft guns that shoot plastic BB's, in some cases you will even find them on Airguns that shoot either lead pellets and/or steel BB's.
It really comes down to where you live as to what your local gun laws have determined is required for your area. You may even live in a region where Airguns and Airsoft guns are not allowed at all! So for you a red or orange tip on the front would be welcome if it would allow you to own an Airgun or Airsoft gun. What about the entire gun being painted a bright color, well that is the case for some folks so again having a red or orange tips may not be as bad as it originally seemed...
In Canada where I live, we used to only be allowed Airsoft guns that had clear sections as our replica gun laws are very strict and all black Airsoft guns would have fallen iinto the "replica" category if they did not have large clear plastic see-through sections on them. This clear section law was revised somewhat over the last several years to allow for all black Airsoft guns here in Canada. It was determined that many Airsoft guns with higher fps limits could cause a serious injury to a human, making them less of a toy in the eyes of the law and more of a weapon. Because of this, Airsoft guns that are capable of shooting a .20 gram plastic BB at a velocity of 360 fps or "higher" are now considered to be similar in the eyes of the law to a regular steel BB or lead pellet shooting Airgun. In Canada, Pellet and Steel BB guns are actually considered firearms of a sort so this allows the higher fps Airsoft guns to be all black since it can not be a replica of a firearm if it is in fact considered to be a firearm by law.
The long and short of all of this is that here in Canada we do not require our Airsoft guns to have orange or red tips since they are considered more or less to be just like any other Airgun and our Airguns do not have red or orange tips either.
Getting back to the title of this article "No Orange Tip On Your Airsoft Gun! Are You Insane?" I often get folks from the US giving me heck for removing the orange tips from my Airsoft guns or asking me why my Airsoft guns don't have them in the first place. These people even state that I could get in a lot of trouble for this! Perhaps they think I live in the US or that US laws govern Canada as well? I am not sure but I can say for the record that I am not breaking any laws at least here in Canada where I live.
I know in the US that wholesalers and retailers by law have to sell Airsoft guns with the affixed orange tips on them, once the end user receives that gun and depending on which state they live in, it may or may not be legal to remove the orange tip. Again, you will need to look into your local state laws as they are different from state to state in the US.
This Video Review focuses on the shooting aspects of the Baikal MP-53M. I test it out to see what kind of velocity it can achieve and I also perform an accuracy test to see how straight and true it shoots.
My first test, the velocity test I performed using my Chronograph shooting 5 7 grain RWS lead pellets. the fps ranged from 303 to 341 fps with an average 5 shot reading of 319 feet per second. Keep in mind the Baikal MP-53M is strictly a target shooter and is not meant for pest control so these readings are perfectly adequate for this this pistols purposes. The lower velocity also makes for a nice easy cocking effort.
Moving on to the accuracy portion of this field test shooting review, I performed my usual 30 foot paper target test using a semi rested stance standing in the back with a sandbag up front to rest my hands on. This position is fairly stable but not perfect so there is always so human factor to consider and with a springer which I am not super proficient at so there where a couple of shot that I pulled. For the most part the majority of my shots with stayed within about a 1 inch grouping but I know with practice the Baikal MP-53M would shoot under a half inch for sure.
A couple of side notes about the Baikal MP-53M Break Barrel .177 Pellet Air Pistol... It has a super nice trigger which is very light and crisp which will aid in accuracy for sure. I did find that the rear sight moved around a little bit, it seemed to rise a bit and I had to press down on it just a little to keep my shots consistent. The spring is not terribly strong so recoil is minimal for a springer and it is very easy to cock.
Getting back to this Field Test Shooting Video, so how did the KWC Jericho 941 CO2 Airsoft Pistol perform for me? I was expecting some pretty decent fps performance sine the steel BB version was a pretty hot shooter but in Airsoft you don't always want crazy high fps performance or the gun may not be usable in any Airsoft games since it could injure an opponent. My 5 shot Chronograph test using .20 gram Airsoft BB's with a brand new 12 gram CO2 gave me an average of 438 fps which is about as fast as you are going to want an Airsoft gun to shoot. This pistol should be capable of hitting targets pretty far down range.
When I setup for the accuracy portion of my Shooting Field Test, as usual I stood 30 feet back from a paper target and used a semi rested stance (sand bag up front and standing in the back). My first round of 10 shots shot really high, with most of the shots hitting the target off camera. So I decided to take another 10 shots but this time with my aim point set at the bottom of the target. Using this method I was able to get all 10 shots fairly well centred on the paper target all within about 3 inches of each other. Not bad. So yes the KWC Jericho 941 CO2 Airsoft Pistol at 30 feet shoots a bit high but depending on what ranges you want it set for it may be just what you want?
The KWC Jericho 941 CO2 Airsoft Pistol is a double action only pistol without blowback operation so the trigger pull is longer and heavier then a blowback pistol with a single action trigger but I would have to say you can still rip off a bunch of quick shots regardless of the heavier trigger pull. In a nutshell the KWC Jericho 941 CO2 Airsoft Pistol is a really solid and consistent shooter with a fairly low price tag and the advantage of full size drop out metal magazines which are perfect for in field shooting.
I have already reviewed the 4.5mm Steel BB version of the ASG Bersa BP9CC and done both a Table Top Video and Field Test Video review for it so make sure to check those review video links out!
In this Field Test Shooting videos review I take the ASG Bersa BP9CC CO2 Blowback Airsoft Pistol through its paces and test it using my Chronograph to see what kind of real world fps we can expect from it. I also perform my usual 30 foot back paper target accuracy test to see what kind of a 10 shot grouping the ASG Bersa BP9CC CO2 Blowback Airsoft Pistol will achieve.
I have to be honest and say that there may have been a problem with the valve in my test unit since I was getting really inconsistent velocity readings using my Chronograph to test out the fps. I could even hear the difference in how much CO2 was being let out with each shot and even the recoil from the blowback slide was sometimes very hard and sometimes very soft. I did end up getting an average of 356 fps but it ranged anywhere from 420 right down to below 300 fps?
With the extreme velocity readings I was getting I did not expect the ASG Bersa BP9CC CO2 Blowback Airsoft Pistol to be super accurate as velocity can really effect the high and low target placement but I was surprised when pretty much all the shots hit within a 3 inch group, with the excepting of a double shot that obviously shot slow and low. This double shot was a result of the slide not kicking back all the way and not reset the single action internal hammer so when I pulled back the trigger I loaded a round into the barrel but could not fire the gun. Resulting in me having to manually pull the slide back and then pull the trigger back a second time, loading a second Airsoft BB into the barrel and firing both BB's at the same time.
My 4.5mm Steel BB version did not seem to have this inconsistent power problem so it may be that my gun either needed some break in time or perhaps had a faulty valve? Even so It actually performed well during the accuracy portion of the test for me.
During this Field Test Shooting Review Video I test out the ASG - Marushin Chrome Derringer 6mm Gas Airsoft Pistol by shooting some rounds through the Chronograph to get an idea on how powerful it really is. I also step back 30 feet and place some rounds down range on my paper target to see just how accurate this little surprise double shot Airsoft pistol is.
In terms of power, all I had to go on was the factory claimed power rating of .6 joules. So I filled up the ASG - Marushin Chrome Derringer 6mm Gas Airsoft Pistol with Propane gas, loaded two .20 gram BB's and shot them both one after the other though my Chrony. I did find that topping up the gas was necessary between loading this gun as the gas chamber is very small. You will only get three shots out of a fill but the last shot is really slow.
I did find that I consistently got right around 250 fps on the fist shot and pretty much bang on 200 fps for the follow-up shot. Not super fast but fast enough to hit a small paper target 30 feet away pretty much every shot. Shooting 6 rounds on my paper target from 30 feet back using a semi rested position I was able to get 5 out of 6 shots pretty well placed on my paper target. I am not sure what happened to the 6th shot but it seemed to hook really hard to the right, perhaps the Airsoft BB was deformed? My 6 shot grouping with the excepting of the one shot that went MIA ended up being about 5 inches, not bad for such a small little low fps pistol.
So in terms of usefulness what can you expect from the ASG - Marushin Chrome Derringer 6mm Gas Airsoft Pistol? Well you are for sure not going to be sniping anyone with it but it could for sure come in handy as a surprise back for your backup gun!
Materials: Mostly metal with some plastic construction.
Weight: 2 pounds (900 grams).
Barrel: 2.25 inches, non-rifled.
Propulsion: 12 gram CO2.
Action: Revolver, single & double actions.
Ammunition Type: 4.5mm steel BB's.
Ammunition Capacity: 6 rounds.
FPS: 328 fps (120 m/s).
Trigger Pull: The trigger pull on the Gletcher CLT-B25 357 2.5 Inch CO2 BB Revolver is good in both single and double action, even better than the Dan Wesson and S&W 327 TRR8 shell loading revolvers, most likely because the spring tension that pushes the inner barrel to make contact with the cylinder is noticeably lighter on the KWC - Gletcher 357's. Even the hammer is smoother and has less wiggle, just a better trigger and hammer mechanism overall.
Accuracy: In terms of power and accuracy, you can checkout my full Field Test Shooting Video here. I did get a nice 2 inch 6 shot grouping on my paper target setup 30 feet away from my standard semi-rested position (sand bag up front and standing in the back). Accuracy was a bit lower than the factory claimed 320 or so fps coming in at an average of 280. I did perform my field test back in May so the weather was not all that warm perhaps effecting peek fps performance somewhat.
Build Quality: The Gletcher CLT-B25 357 2.5 Inch CO2 BB Revolver being mostly metal has a very good build quality, perhaps even better than the Dan Wesson and S&W 327 TRR8 shell loading revolvers, even the weight of the KWC 357 is noticeably more! The only real plastic or rubber I could find was in the grips and the shell tips. Fit and finish was also good with no noticeable wear or sloppy workmanship.
Realism: The KWC - Gletcher CLT-B25 357 2.5 Inch CO2 BB Revolver overall is a close copy a the real steel 357 styled revolver. I did notice the rear portion of the receiver (between the rear cylinder and hammer) to be a bit longer perhaps to accommodate the CO2 valve length, but other than that this pistol is super close to the original 357 styled revolver it is based on. Again being all metal gives this CO2 BB revolver very realistic weight and feel and the loadable brass shells make using this gun almost exactly like using a real shell loading revolver but for much less cost per shot and of course a lot less recoil on the hands that a real 357 magnum or even when shooting 38 special shells for that matter.
It's a revolver with actual shells! Give you the feeling of loading and shooting a real revolver
Mostly all metal design
lots of detail, well made, fit and finish are both good.
Good overall weight, even for this short 2.5 inch barrel version.
Fully adjustable rear sight for windage and elevation.
Well hidden CO2 Screw.
Recessed barrel.
Nice Trigger pull in both single and double action.
Tactical fingered grips look good and allow for a firm hold.
Cons:
Grips are a bit rough, not as rubbery as they look.
Grips may be a bit large for people with smaller hands.
All black sights not great on dark backgrounds.
FPS could be a bit higher!
Comments:
The Gletcher - KWC CLT-B25 357 2.5 Inch CO2 BB Revolver is yet another addition to the increasing lineup of shell loading revolvers available today in both Steel BB and Airsoft versions. The 2.5 inch reviewed here is meant to be the compact version with its snub nosed barrel but I would have to say it is not a small gun at all coming in at 2 pounds and with rather large grips and a pretty large cylinder to pack around. But then again, that may be just what you are looking for? The shorter barrel does effect the fps performance since longer barreled versions of this same pistol I have tested do shoot much hotter but that is to be expected with pretty much any short barrelled CO2 pistol.
My Vimeo Table Top Review for the Gletcher CLT-B25 357 2.5 Inch CO2 BB Revolver:
In this Field Test Shooting video I test out the performance of the KJWorks KP01-E2 (Sig Sauer P226) CO2 Blowback Airsoft Pistol using my Chronograph to get a real world (FPS) Feet Per Second rating. I also position myself 30 feet back and shoot 10 rounds at a paper target using a semi-rested shooting position (Sand bag up front and standing in the back).
In terms of velocity the KJWorks KP01-E2 (Sig Sauer P226) CO2 Blowback Airsoft Pistol shot a bit on the fast side at 414 FPS when averaging a 5 shot strong using .20 gram BB's with a brand new CO2. Keep in mind I was using the CO2 magazine which will have more power than the Gas Magazine version. I would assume the Gas mag version would shoot right around the mid 300's which may be more suited for indoor Airsoft games. For outside Airsoft wars you may want the extra power of the CO2 mag for shooting at targets further distances out.
Stepping back 30 feet and shooting at my paper target, the KJWorks KP01-E2 (Sig Sauer P226) CO2 Blowback Airsoft Pistol produced a decent 2 inch 10 shot grouping that was just a hair low but well centered left and right. The low factor could be adjusted up using some Hop-up tweaking. The trigger in single action mode is light and the release is crisp. Even the double action trigger is fairly light for double action, but there is a lot more take up since your finger is doing all the work that the blowback action would normally do for you when shooting in single action.
With the heavy blowback and high FPS the KJWorks KP01-E2 (Sig Sauer P226) CO2 Blowback Airsoft Pistol creates a really great shooting experience. It would be great for some target practice, getting some additional trigger time in if you are a Sig Sauer P226 owner and would make an excellent outdoor Airsfot war backup weapon. The quality is excellent and as a lover of the Sig Sauer lineup of guns I highly recommend this Airsoft pistol from KJWorks.
