Type: Pellet air revolver.

Distributed by:UmarexUSA.

Model:Single Action Army Revolver with Colt licensing

Materials: Mostly metal with plastic grips.

Weight: 2.35 pounds (1070  grams).

Barrel: 6.75 inches rifled.

Propulsion: 12 gram CO2.

Action: Revolver, single action only.

Ammunition Type: .177 cal. pellets.

Ammunition Capacity: 6 rounds.

FPS: 380.

Trigger Pull: Trigger pull on all the Umarex Single Action Army BB and Pellet Revolver is really great. Being that these Single Action Army Revolvers are single action only, most of the work is done while you pre-cock the hammer with your thumb. The trigger single action pull is under 2 pounds and has virtually no take up with a crisp release. I love the ratcheting sound of the cylinder as you pull back the hammer just like using a real SAA Revolver!

Accuracy: I have not yet tested the Umarex Colt Single Action Army Nickel & Gold Pellet Revolver so far but expect it to perform very similarly to the 4.5 inch barreled pellet shooting version I tested a while back. On that Field Test Shooting review I was abel to get pretty close to the claimed fps with an average of 378 fps. During my accuracy portion shooting from 30 feet back onto a paper target I got a very respectable .75 inch 6 shot grouping using a semi rested position. I do expect the slightly longer barrel on the Nickel and Gold version to perhaps improve fps slightly.

Build Quality: All of the Colt Single Action Army BB and Pellet Revolvers have a mostly all metal construction other than the plastic grips and any seals. The fit and finish is excellent with a great overall weight in the hand. The mechanical action of the hammer and trigger feels just like it would on a real single action army revolver. I really like the two tone nickel and Gold finish on this longer barreled SAA revolver.

Realism: In terms of replicating a real steel Colt Single Action Army Revolver, again these Umarex old west 6 shooters are absolutely amazing replicas. It's really hard to tell the airgun version apart from the real steel version, with the exception of the smaller diameter shells and the discreet safety switch located under the frame. Even the barrel is nicely recessed and has some fake rifling twists in it to give the appearance of a large caliber barrel opening. The CO2 is well hidden with the Allen key built into the handle so no ugly CO2 screw tab hanging down.

Available in the:Replica Airguns Store

Pros:

• Still the best airgun reproduction of the Single Action Army Revolver, a very accurate replica of the real steel old west version.

• Nice large caliber Recessed barrel.

• Great weight and feel in the hand.

• Shell loading design that loads from the back so no need to remove shells if you wish not to.

• Hammer and trigger action is about perfect, no take-up, very crisp and super light (under 2 pounds).

• Nickel and Gold finish looks really great!

• Colt licensing via Umarex.

• Very well concealed CO2 with built in Allen key.

• Discreet safety location under the frame.

• Longer barrel is unique and should get a bit higher fps than the standard  shorter barreled versions.

Cons:

• A lot more expensive than the standard barrel length in standard finishes.

• Real version would shoot 45 caliber, dummy shells are actual closer to 357 so a bit smallish.

• The safety in all of these ghost is really firm and hard to change.

Comments:

We have pretty much established that these Umarex Colt Single Action Army pistols are fantastic airgun copies of the old west real steel 6 shooters in pretty much every way. For this reason they have been super popular! The Umarex Colt Single Action Army Nickel & Gold Pellet Revolver is yet another rendition of this same airgun but with a longer barrel and the tow tone Gold and Nickel finish. You will pay a bunch more for the longer barrel and two tone finish, is it worth it? If your on a budget perhaps not but if you want something that really stands out and may even perform just a little better than pony up the extra bucks and pick one of these beauties up.

My Vimeo Table Top Review for the Umarex Colt Single Action Army Nickel & Gold Pellet Revolver:

Buy the Umarex Colt SAA Pellet Revolver in Canada

I have some new guns for everyone to checkout which is always good for everyone, especially me :)

In this update video I show you around three pistols one Arisoft Rifle. With the pistols we have a mixed bag of Pellet, steel BB and plastic Airsoft. First off I take a look at the ASG X9 Classis Beretta M9 CO2 Blowback 4.5mm Steel BB pistol, which by the way is actually made by KJWorks so we know this it's going to be a quality gun! I then switch things up and showoff the new long barrel CO2 powered Umarex Colt Peacemaker SAA pellet revolver that sports a Nickel and Gold finish. Last for the pistols we take a look at the 6mm Airsoft firing Colt 1911 Rail Gun in the Dark Earth finish, it's basically a KWC 1911 but with a little extra bling.

Last but now least to show you in this update video is the ASG CZ Scorpion EVO 3 A1. This product was developed by ASG in cooperation with CZ and is made to give the Airsoft Player the closest shooting experience they can possibly get to handling and shooting a real CZ Scorpion EVO 3 A1!

ASG X9 Classic Beretta Blowback CO2 BB Pistol:

• Full metal

• 4.5mm steel BB's

• Full blowback action

• 2.1 pounds

• 16 Round full size drop out metal magazine

• 312 fps

• Single & double action

Umarex SAA Colt Peacemaker Nickel & Gold Co2 Pellet Revolver:

• Full metal

• .177 caliber pellets

• Gold highlighted cylinder, hammer & trigger

• 6.75 inch barrel

• Shell loading 6 shooter

• 380 fps

• Single action only

Colt 1911 Rail Gun Dark Earth Blowback CO2 Airsoft Pistol:

• Full metal

• 6mm Airsoft BB's

• Comes with red tip but can be removed with some work

• Full blowback action

• 2.1 pounds

• 17 Round full size drop out metal magazine

• 345 fps

• Single action only

ASG CZ Scorpion EVO 3 A1 AEG Airsoft Rifle:

• Metal & plastic build

• 6mm Airsoft BB's

• Comes with red tip but can be removed easily

• AEG: single shot, 3 round and full auto shooting modes

• 5.3 pounds

• 75 Round magazine

• 394 fps

• Full CZ licensed

Buy Umarex SAA Colt Peacemaker Nickel & Gold Co2 Pellet Revolver in Canada

Buy ASG X9 Classic Beretta Blowback CO2 BB Pistol in Canada

Buy ASG X9 Classic Beretta Blowback CO2 BB Pistol in the US

Buy Colt 1911 Rail Gun Dark Earth Blowback CO2 Airsoft Pistol in Canada

Buy Colt 1911 Rail Gun Dark Earth Blowback CO2 Airsoft Pistol in the US

Buy ASG CZ Scorpion EVO 3 A1 AEG Airsoft Rifle in Canada

Buy ASG CZ Scorpion EVO 3 A1 AEG Airsoft Rifle in the US

This year at SHOT Show 2017 in Las Vegas, I found there wasn’t a lot of new Airgun products but as always there are some that stood out for me. If you want more info on each Airgun Company then make sure to watch my full interviews for this years SHOT Show 2017. So without prolonging this video any longer let’s get right into it…

Umarex Legends MP CO2 Full Auto German MP40 Replica Machine-gun:

What’s not to like about the Umarex Legends MP? It has lots of metal parts weighing in at 7.7 pounds, a 60 round steel BB magazine with a dual 12 gram CO2 system. You also get your choice of shooting either in semi auto or full auto at up to 400 fps. Personally the Umarex Legends MP was the most interesting Airgun at the show this year for me and I really think it is going to be a hit!

Umarex SA10 Blowback Pellet and BB CO2 Pistol:

Another interesting product from Umarex this year was the SA10, I am not really sure what it is exactly styled after, it’s more of a futuristic looking gun with slide venting and a thread barrel for adding a mock suppressor or compensator. What appealed to me most about the Umarex SA10 was the new magazine design that incorporates a full size drop out metal magazine with 4 rotary 8 round magazines that can be loaded with either pellets or BB’s. When you empty one 8 shot magazine you simply drop the entire mag out and swap your empty 8 shot rotary magazine for a full one. The SA10 has a nice weight of around 2 pounds and shoots up to 426 fps.

Sig Sauer ASP P320 CO2 Blowback Pellet Pistol:

Sig Sauer introduced their new Sig Sauer ASP P320 CO2 Pellet Pistol this year that will be replacing the P250. Like the P250 the Sig P320 has a metal slide and polymer frame but instead of a double sided 16 shot rotary magazine, the Sig ASP P320 has a newly designed and very unique 30 round belt fed magazine. That’s nearly double the capacity without having to flip the magazine around part way through shooting. It’s great to see innovations like this happening in the airgun market.

Crosman Remington 1875 Shell Loading CO2 Pellet and BB Revolver:

Crosman introduced their own Single Action Old West Revolver this year in the form of the Remington 1875. Like the super popular Umarex Single Action Army Revolvers, the Remington 1875 is also shell loading and uses 12 gram CO2. You have the option of shooting either Pellets or BB’s out of its smooth bore barrel. I expect the Crosman Remington 1875 Shell Loading Revolver to be another popular Old West Airgun Revolver.

Crosman PSM45 Single Shot Spring Powered BB Pistol:

The Crosman PSM45 at first glance may not seem that interesting, after all it’s all plastic on the outside and only shoots about 200 fps! On the plus side it kind of looks like a Glock and we all know how hard it is to find airguns these days that resemble a Glock. I also like the fact that there is no need for any CO2, and most springers out there look like springers while the Crosman PSM45 looks like a real semi auto pistol. The PSM45 even has pretty decent weight to it since there are lots of internal metal parts and a full size drop out metal magazine which was a real surprise in such an entry level low cost pistol. If you’re looking for a fun inexpensive replica plinker than the Crosman PSM45 should fit the bill. On a side not the PSM45 would also make a really great low cost prop since the slide does work and it has that full size drop out magazine!

ASG Dan Wesson 715 2.5 and 4 inch Shell Loading CO2 Revolvers:

The ASG Dan Wesson Revolver has always been a popular choice, and then the Dan Wesson 715 came out improving on the design by adding extra weight and smoothing out the mechanics. How do you top that? Well by giving us some more options like barrel lengths. You now have your choice of a 2.5, 4 or 6 inch barrel for the Dan Wesson 715 and of course you will be able to buy your 715 pick in 4.5mm Steel BB, 6mm Plastic Airsoft or .177 Caliber Pellet ammunition versions. My personal choice may be the 4 inch Dan Wesson 715 since it has the addition of an integrated accessory rail machined into the outer barrel for lasers or tach lights.

Gletcher M1944 Mosin Nogant CO2 BB Rifle:

The Gletcher M1944 Mosin Nogant CO2 BB Rifle is not a new replica gun this year but it has been a hard one to get your hands on. In fact up until SHOT Show 2017 I had never seen one in person and so the Gletcher M1944 is new to me. I was very impressed with the quality of the Gletcher M1944 Mosin Nogant, it has a lot of metal parts including the swing out bayonet and even the simulated wood stock looks like real wood. I even had to take a second look and ask before confirming that the stock is in fact plastic on the Gletcher M1944 Mosin Nogant. I am looking forward to reviewing this rifle in the future when I do finally get one!

Of course there where other interesting products at SHOT Show 2017 this year but those are the products that stood out the most for me. Again make sure to watch my full interview videos to find out more about all the new products at this years SHOT Show.

My last Interview for SHOT Show 2017 in Las Vegas, well at least till next year and I am already looking forward to going back and doing it all over again :) I met with Boris Shekhman from Gletcher and Boris showed me several of their Gletcher Airguns along with a new accessory introduced this year.

Probably the highlight at the Gletcher booth was the Gletcher M1944 Mosin Nagant CO2 4.5mm Steel BB Bolt Action full stock air rifle! I already reviewed the Gletcher M1891 short stock version but have been really looking forward to seeing the Gletcher M1944 Mosin Nagant in person. Interestingly, Boris was asked by the SHOT Show staff to remove the Gletcher M1944 Mosin Nagant from his display because the real metal swing out bayonet was a concern for them. Boris was kind enough to bring out the Gletcher M1944 for me to see and video for everyone. The full stock however is not real wood but you need to look super close to figure this out as the reproduction is incredible.

We took a look at another Gletcher Airgun I have reviewed in the past, the Gletcher NGT and Gletcher NGT R which are very acurate Steel BB and Pellet shooting reproductions of the Belgian Nagant Revolver. Both these BB and Pellet shooting NGT's are getting a slight make-over with the addition of a safety on them, the real steel versions do not have a safety but some dealers felt it was a concern so Gletcher moving forward will be including a safety on all new NGT's. So if you want a more original Gletcher NGT Nagant Revolver then hurry up and pickup the older non-safety versions while they are still available!

Last on the list of new products from Gletcher are some really great looking leather holsters that not only work for several Gletcher airgun products but can also be used for the same real steel versions. Some of the pistols these new leather holsters will accommodate are the Gletcher TT Tokarev, 1911, Grach, PM 1951 Makarov, and the Stechkin.

Enjoy my latest SHOT Show Interview with Jesse Caster from Crosman. Jesse shows me Crosman’s latest old west single action revolver, the Remington 1875 which shares a lot with the super popular Colt Single Action Army revolvers. Jesse also goes over some new airgun pistols with me, a CO2 powered non blowback 1 to 1 replica of the Remington RP45, a very interesting single shot spring piston “Glock-ish looking pistol called the PSM45. And last but not least, Crosman has now got on the Beretta / Taurus bandwagon and added the PFAM98 to their lineup.

Crosman’s new Remington 1875 should be a welcome addition for anyone looking to add something new to their Old West Airgun lineup. The Crosman Remington 1875 like the Colt Single Action Army Revolver is shell loading, shoots in single action only and has that super slick ratcheting cylinder we all love. The Crosman Remington 1875 shoots both .177 caliber pellets and 4.5 mm steel BB’s from its smooth bore barrel, but Jesse has gone on record to claim that the pellets work well and shoots pellets and BB’s accurately at ranges typical for this type of Airgun.

Another Remington Licensed Airgun from Crosman this year is the Remington PR45. The PR45 is a 1 to 1 replica of the real steal Remington RP45 but in a CO2 non-blowback 4.5mm BB shooting version. The Crosman PR45 has a metal slide and polymer frame with a drop out all metal stick magazine. Some other notable features for the Crosman PR45 are a working trigger safety and white dot sights front and back.

If you are looking for something a little different from Crosman this year then checkout the single shot spring piston PSM45. This super affordable air pistol kind of looks "similar" to a Glock and lord knows how many times I get asked what is available in an airgun that resembles a Glock. The Crosman PSM45 is not going to win any fps awards (shoots around 200 fps), but there is no need to buy any CO2 and you can shoot this airgun in virtually any temperature for only the cost of steel BB’s. The frame and slide on the Crosman PSM45 are plastic but it does have decent weight do some internal metal parts and an unexpected full metal full size drop out magazine.

Crosman this year is adding a Beretta/Taurus full metal and full blowback CO2 BB Pistol to their product lineup. You may have already guessed it, it’s essentially a KWC Beretta / Taurus which really isn’t a bad thing since the KWC Blowback Beretta / Taurus has been very popular with replica airguners. A nice little treat with the Crosman PFAM98 Beretta / Taurus is that right out of the box it shoots in both semi and full auto using the ambidextrous selector safety switch.

Another SHOT Show 2017 interview video, this interview is with Bob Li from ASG (Action Sport Games), Bob shares with me some updates to the super popular Dan Wesson 715 along with the reintroduced EVO Scorpion Inferno powered Airsoft Rifle. Bob finishes up with a new X9 Classic which is a Beretta M9 in 4.5mm Steel BB.

You may have thought the Dan Wesson 715 was already pretty much perfect as is so what could ASG to make it even better? How about different barrel lengths. ASG has introduce the Dan Wesson 715 in both a new 2.5 inch and 4 inch version. Both lengths will be hitting stores shortly and will come in .177 caliber pellet and 4.5mm steel BB options. 6mm Airsoft will be out later on. The 4 inch version also includes an integrated accessory rail machined into the outer barrel for those of you wanted to add items like lasers and tactical lights to your Dan Wesson 715.

Last year at SHOT Show ASG introduced the EVO CZ Scorpion 3 A1 Inferno powered Airsoft Rifle but is again reintroducing it this year since they decided to take their time and get it perfect before releasing it in stores this March. The EVO CZ Scorpion 3 A1 is Inferno powered using an HPA system with a custom chip set that allows for a three round burst option an empty magazine detection.

ASG has sourced out not just any 4.5mm Steel BB shooting M9, they are actually getting their new ASG X9 Classic built by KJWorks. KJWorks is known for their Airsoft guns and I have reviewed several of them to date. If you have been looking for a KJWorks M9 but would prefer it to be in 4.5mm Steel BB then the new X9 Classic 4.5mm Steel BB KJWorks M9 exclusive to ASG is where you can get one!

It's been a great year for Replica Airguns and I wanted to share with everyone some of my favorites that I reviewed this year. In this Vimeo Video I show some of my top Replica Airgun picks for 2016 and talk a little bit about each one and what I like about it.

Here is a list of the Replica Airguns in this lineup:

• ASG Dan Wesson 715 CO2 Revolver - Comes in 4.5mm Steel BB, 6mm Plastic Airsoft & .177 Pellet.

• Umarex Colt Combat Vet CO2 Blowback 1911 - 4.5mm Steel BB.

• Sig Sauer MPX ASP CO2 Rifle - .177 Pellet.

• Sig Sauer ASP P226 CO2 Blowback Pistol - .177 Pellets.

• Air Venturi ISSC M22 CO2 Blowback Pistol - 4.5mm Steel BB.

• KJWorks KC-02 V2 Ruger 10/22 GBB Rifle - 6mm Plastic Airsoft.

• Umarex S&W M&P40 CO2 Blowback Pistol - 4.5mm Steel BB.

First off I want to say it’s hard to trouble shoot technical or mechanical problems over the internet regardless of if ithas to do with guns, cars, computers or pretty much anything where unless you are there in person it’s really hard to figure out the problem.

But I will attempt to address some of the more common issues why a blank gun may not be functioning properly.

Why is my Semi Auto Blank Gun Not Cycling or Ejecting Shells?

One very common reason a blank gun may not be cycling the shells properly is because the owner has removed the barrel restrictor plug. People usually do this to make the barrel opening look more realistic but the barrel restrictor is a necessary component to increase the back pressure allowing the slide to cycle fully to the rear position so it can eject and pickup a new shell.

The blanks you are using may not have enough gun powder in them. Some blank guns require banks with more gun powder than others, again this additional internal pressure forces the slide all the way back, if the blank does not have enough gun powder in it then only a partial slide motion happens and so the discharged shell may not eject properly, in this case the user would have to clear the blank gun manually so another shell can then be picked up and loaded into the breach.

If your blank guns is dirty or not lubricated then it may act sluggish again restricting the full movement of the slide which will effect correct operation. Make sure to thoroughly clean and lubricate your blank gun, that may be a quick fix for you!

You may have a faulty extractor? The extractor is like a hook that grabs the discharged shell while the slide is in the reward position pulling or extracting the shell out of the breach. If the extractor is worn or broken then the empty shell will not be ejected from the breach so when a new shell is picked up from the magazine it has nowhere to go and usually you will get a jam-up in the ejection port area.

One final situation that can cause your blank gun to not cycle properly is to strong of a slide spring, some blank guns out of the box just come with a really heavy slide spring, so much so that even blanks with lots of gunpowder in them are still not strong enough to make the slide operate full motion. Your only option here would be to replace the heavy slide spring with a lighter one.

Why Are My Blanks Not Firing?

This is a situation where you pull the trigger and nothing happens. Lets get the obvious causes right out of the way here… Did you put blanks in your gun and are they new blanks? Did you chamber the first round in your semi auto pistol?

So now that that’s out of the way let’s look at some other reasons why your blank gun may not be firing a blank. Perhaps the firing pin is broken? Most blank guns are not made out of carbon steel and even the firing pins can be lesser quality than what you would find in a real gun so blank guns are more prone to breaking than real guns. I have seen broken firing pins in blank guns first hand so make sure to check the firing pin and that it is fully operational.

Try changing up your blanks to another brand? Again blank gun ammunition is not made to the same higher standards that real firearm ammo is made and some primers may require a little more pressure than your gun is providing. Even with real guns an ammo change may help the gun operate better.

Why is the Trigger or Hammer Not Operating Properly?

I have come across blank guns where there are mechanical problems in the trigger and hammer areas, you may be able to address this yourself but I would recommend taking your blank gun to a gunsmith since you will have to take the gun pretty much full apart to fix a problem in the trigger and hammer areas.

Of course make sure your gun is clean and lubricated, this can help a lot with the mechanical areas of your blank gun.

One problem I saw with a few EKOL Special 99’s was specifically with the single action potion of the trigger, when I would pull the hammer back it would not lock back and the hammer would often slip and fire randomly, this is rather dangerous. When I took the gun apart I found that the table top or step that the trigger was supposed to catch on was worn down on the edge so it would simply slip off. I was able to fix this by filing a new edge on the step area. Again this can happen because blank guns are not made out of as high quality metal materials as real guns.

Why does the Flame Come out the Top of My Blank Gun and Not the Front?

If you find that the flame or discharge comes out of the top of your blank gun and not the barrel, this usually does not mean anything is wrong with your blank gun. All it means is you own a top venting blank gun and not a front firing blank gun. In some countries front firing blank guns are not allowed but front venting blank guns are. The same may also be reversed in some countries, for instance here in Canada we can only import front firing blank guns with flare adaptors since our blank guns are imported under the assumption that they are to be used as signaling or flare devices.

Can I Convert my Top Venting Blank Gun into a Front Venting Blank Gun?

I really don't recommend altering a blank gun in any way as it may be a violation of your local laws and it could cause the blank gun to malfunction in a very bad way causing serious injury or even death!

In theory I suppose it may be possible to convert your Top Venting Blank Gun into a Front Venting Blank Gun but again you would need to allow for just the right amount of back pressure so a wide open barrel would not work unless it was a revolver. You can not simply remove the red plug and bingo you have a front firing blank gun because in most cases the barrel will be completely plugged in the frontal region. Not only would you need to drill out the plugged portion of the barrel but you would also have to somehow fill in the top venting area and again makes sure to allow for just enough back pressure to cycle the slide back and forth.

Hopefully this has helped some of you with blank gun issues. If you’re looking for a blank gun make sure to come down to www.ReplicaAirguns.ca and www.ReplicaAirguns.us and have a look in our blank gun area of our online stores.

Power Sources Covered in this review: CO2 - Green Gas / Propane - Spring - AEG / AEP (Automatic Electric Gun - Airsoft Electric Pistol)

Pro’s:

• CO2 Airsoft Guns allow for fast repeat shooting, great for action shooters, generally CO2 Airsoft Guns will have a little more power then Green Gas Airsoft Guns. There is no need to pump or cock your CO2 powered Airsoft gun in-between shots and a CO2 power source can allow for a very realistic action of the gun you are shooting. 

• Green Gas (Propane) Airsoft Guns operate much the same as CO2 Airsoft guns so they all make for great action shooters and the Green Gas powers the mechanical operation allowing for very realistic operation. Green Gas (Propane) Airsoft Guns can cost a little bit less to operate that a CO2 Airsoft Gun especially if you plan to use Propane as it can be cheaper to buy than the smaller 12 gram CO2 Cartridges.

• Spring Airsoft Guns are generally fairly basic and low cost so they are the usually the most affordable Airsoft guns to buy. There is no need to buy CO2 or Green Gas or even a Battery and Charger Setup so the cost to shoot Spring Airsoft Guns is only going to be subject to the Airsoft BB’s you plan on buying.

• AEG (Automatic Electric Guns) have the most consistent power as they use a spring internally that the electric motor draws back before each shot, the internal spring will essentially apply the same force to the Airsoft BB’s with each shot. AEG (Automatic Electric Guns) are a great option when you are wanting a Full Auto Airsoft gun since there is no cool down effect and as long as your batteries are charged and you have Airsoft BB’s in your magazine, the gun will simply keep shooting. AEG (Automatic Electric Guns) allow for the highest capacity magazines and often hold as many as 500 Airsoft BB’s in a single magazine. So if you’re looking for raw firepower an AEG or AEP Airsoft Gun is your best option. Once you have purchased your AEG (Automatic Electric Gun) and a battery and charger setup, they are fairly inexpensive to operate since no CO2 or Green Gas is required.

Con’s:

• CO2 Airsoft Guns require the additional cost to buy the CO2 cartridges as they will not function without it. CO2 Airsoft Guns have a limited power output and lose power as you shoot and use up the CO2. CO2 Airsoft Guns are effected by hot and cold temperatures and will have less power in colder temperatures and may not even work in super cold environments. CO2 Airsoft Guns will have a more conservative ammunition capacity since too high of a capacity magazine would freeze up the magazine and even the gun.  

• Again since Green Gas (Propane) Airsoft Guns work much like CO2 Airsoft Guns, they are effected by cool down and lose power when shoot quickly or as the Green Gas or Propane runs low. Green Gas does not expand as much as CO2 so it will not be as powerful and even less effective in colder temperatures. Green Gas Airsoft Guns will have a more conservative ammunition capacity since too high of a capacity magazine would freeze up.

• Spring Airsoft Guns are not the best action shooters since you need to manually operate the slide to pullback the spring prior to each shot, this does work well with Pump, Lever and Bolt Action Airsoft guns but is not the best option for pistols since most real steel pistols operate in semi auto mode.

• If you plan to use your AEG (Automatic Electric Gun) in a battle then it will require a multi battery setup which does cost a bit more upfront. AEG (Automatic Electric Guns) are know to not operate as realistically as a CO2 or Green Gas Airsoft gun since CO2 and Green Gas Guns do allow for the same realistic mechanical operation which can give very believable blowback operation, this is hard to replica with an AEG Airsoft Gun.

Power Sources Covered in this review: CO2 - Spring Piston - Variable Pump -HPA (High Pressure Air)

Pro’s:

• CO2 Airguns allow for fast repeat shooting, great for action shooters, generally CO2 Airguns will supply a medium power range. No need to pump or cock your CO2 powered weapon in-between shots and a CO2 power source can allow for a very realistic action of the gun you are shooting.

• Spring Piston Airguns are best suited of single shot situations, they can provide low to high power output depending on the spring used. Spring Piston Airguns are very low cost to operate since you only need to buy the Pellets or BB’s. Spring Piston Airguns are not greatly effected by outside temperatures.

• Variable Pump Airguns allow you to decide how much power your gun will have and can offer very high power output depending on the Airgun. Variable Pump Airguns are very low cost to operate since you only need to buy the Pellets or BB’s. Variable Pump Airguns are not greatly effected by outside temperatures. Variable Pump Airguns generally have very low recoil and vibration.

• HPA (High Pressure Air) Airguns generally do not require pumping or cocking in-between shots and some even come in semi automatic or bolt action. HPA Airguns can have very high power output and even be used on larger game using large caliber ammunition. HPA Air Rifles have lower recoil and low vibration. HPA Airguns can be charged ahead off time so they are ready for use when you need them.

Con’s:

• CO2 Airguns require the additional cost to buy the CO2 as they do not function without it. CO2 Airguns have a limited power output and lose power as you shoot and use up the CO2. CO2 Airguns are effected by hot and cold temperatures and will have less power in colder temperatures and may not even work in super cold environments.

• Spring Piston Airguns require cocking before each shot. Spring Piston Airguns can have a lot of recoil and vibration, so much so that special optics must be considered when buying an optical sight. The action of the spring recoil can effect accuracy, especially if you are not use to the vibration and recoil or have spent some time practicing using a Spring Piston Airgun.

• Variable Pump Airguns will require multiple pumps to achieved maximum power output which can take some time in-between shots. So you are going to have to work for each shot.

• HPA (High Pressure Air) Airguns require the use of a manual pump to fill their built in air tank to maximum pressure and it does take a lot of time to manual fill an HPA tank. Alternatively you can have the air tank filled at a shop or buy a pressurization system similar to a scuba tank out paintball setup, the cost of this setup can be very high but will save you the castle of manually pumping air in to your HPA Airgun. HPA Airguns are generally a little more bulky then other Airgun systems since they have to accommodate fairly large air pressure tanks.

Power:
Generally speaking a longer barrel is going to allow for more power. If you compare most CO2 pellet pistols to CO2 Pellet Rifles, you will find that the CO2 Pellet Pistol will generally shoot about 300-400 fps using a standard lead Pellet. On the other hand many CO2 Pellet Rifles can get up to as high as 600 fps which is much better speed for humanly shooting some smaller pests.

If you are talking about Springer or Variable Pump Air Pistols versus their Air Rifle counterparts, again the Air rifles will generally shoot with much more power. I have seen some none CO2 Air Pistols shoot up into the 500-600 fps range but again compered to none CO2 Air Rifles, they can even double these numbers.

Some of you may ask about Steel BB Pistols and Rifles. I personally would never really sue this type of ammunition for pest control simply because most BB Rifles have much less raw power than Pellet Rifles and steel BB’s will not be as accurate at any type of longer distance.

Stability:
When holding any rifle from the shoulder, you have three point of contact with your body spread out in a much longer distance than a two handed pistol grip. Holding steady even without a rested position is much easier using a rifle. Even when using a rested position, the rifle will more stable.

Accuracy:
A big factor in accuracy is stability but there are also other factors to consider. Barrel length its self does not make the gun more accurate, you only need a few inches of barrel length to get constant accurate results from a gun. What makes longer barreled guns more accurate is the distance between the rear and front sight. The closer the sights are together, the more margin for error there is, the longer you spread out the sights from each other, the more accurate the sighting system becomes.

Overall More Humain:
When you consider Air Rifles tend to have higher power, better accuracy and overall more consistency than shorter barreled Air Pistols. The logical choice for humanly shooting a Pest is to use the Air Rifle. The last thing you want to do is make any animal suffer, even if it has been causing a lot of havoc around your home or farm or place of business.

This is not to say that a “Real Gun” is not as good as an Airgun or better in other ways, in this video I’m just pointing out how an Airgun in some cases can actually be better suited than a Real Gun.

Availability: What I mean by this, is that in many countries Real Guns can be very hard to acquire and often require safety course and applications before one can purchase a Real Gun. I have no problem with this but it is a reality that must be considered. Having an Airgun versus not having a gun at all makes it a better option for people that live in countries that have strict gun laws. Here in Canada we are allowed Real Guns, even pistols but we do have restriction on our pistols and so I can only get certain guns in an Airgun version. As a collector this is better than not having the gun at all.

Price to Buy: Generally speaking you can pickup an enter level Airgun for much less money than a real gun.

Cost to Shoot: Real gun ammo prices have been steadily increasing to the point that a day out shooting can cost several hundred dollars just on the ammunition alone.

Comparison of Price:

• 50 rounds of 9mm ammo will cost around $18.00

• 6000 rounds of 4.5mm Steel BB will cost about $18.00

• CO2 is a bit less than $1 per 12 gram Cylinder which can yield up to 100 shots each.

• To shoot 100 rounds of 9mm will cost close to $40 versus 100 shots of 4.5mm steel BB at around $1.

• For this reason alone an Airgun can make a lot of sense even for Real Gun owners looking to get more cost effective practice time.

Access to Shooting Locations: Depending on where you live you will have to consider your local laws and where you are allowed to shoot both types of guns but typically you can shoot an Airgun safely just about anywhere as long as you implement some backstop safety precautions. Here in Canada we can only shoot a pistol at designated gun ranges, where as Airguns have a lot more allowances to shot them as long as you are not braking any city bylaws.

Training Guns: Even if you plan to eventually step up to a Real Gun at some point, an airgun is a great option to first learn proper gun handling skills since if you where to make a mistake, the consequences are much less severe. Airguns are also a lot less intimidating than a real gun since they are much quieter and have less recoil, you don’t even need to wear ear protection with most Airguns which means an instructor can communicate to his pupil on the range a lot easier.

Prop Guns: Since Replica Airguns look so much like real guns these day, they can often be used as a safer substitute for use in Movie, TV or other Photo and Video productions. Using a Real Gun on set generally requires a certified “Gun Wrangler” be on hand as Real Guns must be transported, stored and handled using very strict regulations. Airguns generally do not need to follow the same rigid regulations that Real Guns are bound to.

Tactical Training with Live Targets: Obviously shooting a real gun at a live target would not fair well for anyone involved, so that is completely out of the question. Airsoft Airguns are however perfect for Tactical Training and other weapons based simulations. All that is required for safety when using Airsoft guns is the use of eye protection and generally some heavy clothing.

I am sure there are some more areas in which Airguns may have the advantage over a Real Gun but these are the main ones that I could think of.

I already made several review videos for both Gletcher NGT (4.5mm Steel BB) and the Gletcher NGT R (.177 Cal Pellet) Revolvers, including table top and shooting videos. So make sure to check those videos out for more information on both versions of Gletcher NGT and NGT R Revolvers.

I did however miss some noteworthy details that I wanted to cover in this video. Firstly, the real steal Nagant M1895 Revolver this Gletcher NGT is styled after has a very unique gas-sealing system that the Airgun version does not replicate or really require but it is worth mentioning.

Here is some more info on how the original Nagant M1895 Revolver Gas Seal System works:

(From Wikipedia) The M1895 by contrast, has a mechanism which, as the hammer is cocked, first turns the cylinder and then moves it forward, closing the gap between the cylinder and the barrel. The cartridge, also unique, plays an important part in sealing the gun to the escape of propellant gases. The bullet is deeply seated, entirely within the cartridge case, and the case is slightly reduced in diameter at its mouth. The barrel features a short conical section at its rear; this accepts the mouth of the cartridge, completing the gas seal. By sealing the gap, the velocity of the bullet is increased by 15 to 45 m/s (50 to 150 ft/s.) This feature also eliminates the possibility of injury through the dangerous expansion of gases from the cylinder behind the barrel, which are easily capable of severing a finger if the user holds the gun incorrectly (with a finger positioned in front of the cylinder during fire) - a noted safety-issue in conventional revolvers.

Moving on to some of the features incorporated into the Gletcher NGT NGT-R CO2 BB and Pellet Revolver that I did not point in any of my previous videos. There is an extractor rod that can be used to extract a shell, this is not really necessary on the airgun version since the shells do not expand and tighten on the cylinder as they would n the real steal Nagant M1895 Revolver built is nice that we can replicate this feature with the Airgun version. You can also remove the cylinder completely from both the BB and Pellet shooting Gletcher NGT NGT-R CO2 Revolvers. The cylinder is actually very heavy and adds a lot of weight to this compact 7 shot Revolver.

It is always nice when an Airgun is built in such a way that it replicates the real steal version as closely as possible and the Gletcher NGT NGT-R CO2 BB and Pellet Revolvers do this nearly perfectly.

Buy Gletcher NGT Revolvers in Canada

Buy Gletcher NGT Revolvers in the US

I get asked on a daily bases form many of my Vimeo Viewers about how and if there is a way to get rid of the White lettering on Airguns, Typically people are wanting to remove the intrusive Warning instructions from Airguns like the Cybergun Tanfoglio Witness 1911, the Cybergun/Swiss Arms GSG 92/P92 and many other CO2 Replica Airguns that have lettering or branding that you may want to get rid of.

In this Instructional Tutorial Video I show you how can at least tone down the white lettering and even completely remove it on some Airguns without damaging the Airguns finish underneath the white lettering. You will have to use some patience and perhaps repeat this method a few times but the end result is worth the effort.

The magical product I use to remove the white lettering on many popular Airguns is a product from Birchwood Casey called the Presto Gun Blue Pen. This product is actually designed to touch up real steel gun in areas where the blueing has worn off, lucky for us the Birchwood Casey Presto Gun Blue Pen also works well to remove the ugly white lettering from Airguns.

I have often been asked which of the Shells for the Shell Loading Revolvers work in which Shell Loading Revolvers? After all many of them look a lot alike so can you mix and match Shells for the various types of Shell Loading Revolvers?

In this Vimeo Instructional Video I test out a bunch of Shells to see which ones actually will work or not work in several of the most popular Shell Loading Revolvers.

Some of the Shell Loading Revovers Tested in this Instructional Video are:

• Dan Wesson Classic Revolver (BB, Airsoft, Pellet)

• Dan Wesson 715 Revolver (BB, Airsoft, Pellet)

• Colt Single Action Army Peacemaker (BB, Airsoft, Pellet)

• Gletcher NGT and NGT-R (BB and Pellet)

• Webley Mark VI (BB)

• KWC 357 / Umarex 357 (BB, Airsoft)

• G&G G731 (Airsoft) 

I have already made a Table Top Video Review for the Gletcher NGT Silver CO2 BB Revolver which for the most part is the same gun but in a 4.5mm Steel BB non rifled barrel version and as the title indicates with a different finish being the silver version. Other than finish and ammunition being used, both guns are virtually the same.

I always like getting outside and shooting the airguns I review even on these fall overcast days, at least the temperature was not too cold, right around 14 °C or 57.2 °F so decent for my testing purposes. The Gletcher NGT R like the BB shooting NGT is a fairly small air revolver and so pretty much anyone should be able to shoot this air revolver even if you have smaller hands, I did find that pre-cocking the hammer for single action shooting was a bit of a stretch when reaching over with the thumb, but you can just as easily shoot in double action, both trigger pulls are nice and light with the double action being a bit longer and heavier.

Loading the 7 round cylinder will take longer than your standard stick magazine BB pistol since you first need to pop some .177 caliber pellets into each shell, if you want to speed up the process you don't have to eject the shells to load them, you can simply index the cylinder and pop a pellet into each shell while still inside the cylinder.

In terms of fps performance, the Gletcher NGT R CO2 Pellet Revolver shot a little higher than expected getting a 4 shot average of 376 fps using 7 grain RWS Lead pellets, so around 50 fps higher than the claimed 328 fps on the box and even a bit higher than the steel BB version I tested earlier. This is really good considering the short barrel and fact that a revolver can leak a little CO2 between the cylinder and the barrel and even the cylinder and the CO2 valve.

I really felt comfortable using the rather old school fixed open post and notch sights, the grey/black finish on the Gletcher NGT R may be a bit hard to see on darker targets but shooting on my white target was no problem. My 7 shot grouping from 30 feet back using a semi rested shooting stance produced about a 1 inch grouping well centred vertically just a hair to the left so all in all the Gletcher NGT R CO2 Pellet Revolver has the power and accuracy I was hoping for even in such a small package.

I would definitely recommend the Gletcher NGT R CO2 Pellet Revolver, not only is it a real looker but it also has the performance to back it. even better than its 4.5mm Steel BB shooting brother.

Buy the Gletcher NGT R CO2 Pellet Revolver in Grey/Black in Canada

Buy the Gletcher NGT R CO2 Pellet Revolver in Grey/Black in the US

Buy the Gletcher NGT R CO2 Pellet Revolver in Silver in Canada

Buy the Gletcher NGT R CO2 Pellet Revolver in Silver in the US

It has been a while since I picked out some of my favorite guns, after all my favorite gun picks change on a daily basis since there are so many awesome guns out there to pick from.

This Vimeo video is a little different since I pick out my favorites from a bunch of mostly replica gun categories including Steel BB, Pellet, Airsoft, Revolvers and Blank Pistols.

You may notice most of my picks happen to be blowback guns but to me airguns are all about being as realistic as possible and having blowback operation to me help to simulate the realism that much more. The exception in this video is in the pellet gun category since I decided on a pellet gun that was more about function and purpose over being any type of real replica.

Hopefully you take the time to watch my entire Vimeo video since I also bring out some close runner ups but here is a list of my top picks on this day, tomorrow it could be a completely different list of guns ;) 

• Steel BB - Umarex/KWC Smith & Wesson M&P 40 CO2 Blowback BB Pistol

• Pellet - Webley & Scott Tempest .22 Caliber Pellet (Spring Piston)

• Airsoft - KJWorks KP-11 1911 Hi-Capa 1911 CO2 Blowback Airsoft Pistol

• Blank - ROHM RG-88 9mm P.A.K. Blank Pistol

• Revolver - Dan Wesson 715 Revolver (BB, Airsoft, Pellet Versions)

Buy Umarex/KWC Smith & Wesson M&P 40 CO2 Blowback BB Pistol in Canada

BuyUmarex/KWC Smith & Wesson M&P 40 CO2 Blowback BB Pistol in the US

BuyWebley & Scott Tempest .22 Caliber Pellet (Spring Piston) in Canada

Buy KJWorks KP-11 1911 Hi-Capa 1911 CO2 Blowback Airsoft Pistol in Canada

Buy ROHM RG-88 9mm P.A.K. Blank Pistol in Canada

This comparison Review Video serves a few purposes, first to compare the ASG Dan Wesson 715 Revolver 4.5mm steel BB version to the 6mm plastic Airsoft version in both velocity and accuracy. Secondly to give my new Chrony Chronograph with lighting kit a test to see if I can get more reliable readings in lower light and thirdly to try and redeem the Steel BB version of the Dan Wesson 715 as last time I tested it, it did not get all that high of fps readings, well below the claimed 430 on the box.

In this review video I test both Dan Wesson 715 Revolvers out, first with my Chrony Chronograph and then all in one take I setup and shoot 6 rounds each on separate paper targets from 30 feet back to see how accurate the smaller heavier Steel BB rounds are compared to the larger lighter Plastic BB's. I used 5.1 grain RWS 4.5mm Steel BB's and .20 gram 6mm plastic BB's and installed brand new 12 gram CO2 cartridges in both guns.

In terms of my Chrony consistency, the smaller steel BB's still struggled to get consistent readings with only 2 out of 6 shots while the larger Airsoft BB's managed to get a good reading 4 out of 6 shots. Steel BB velocity was right around 350 fps while the Airsoft BB's where travelling much faster at closer to 450 fps.

Both the Steel BB and Airsoft CO2 Dan Wesson 715 Revolvers shot 6 round grouping of about 2 inches with 4 out of the 6 shots making a much tighter 1 inch group again with both ammo types. The Airsoft Dan Wesson 715 seemed to be centered on target well while the Steel BB Dan Wesson 715 shot a bit low.

Buy the Airsoft Version in Canada

Buy the Steel BB Version in Canada

Buy the Steel BB Version in the US

Type: Blank front firing pistol.

Manufacturer: SM.

Model: Mod 110 8mm.

Materials: Mostly metal with plastic grips.

Weight: 11.75 Ounces (332 grams) Unloaded.

Barrel: Front firing.

Propulsion: Gun powder.

Action: Semi auto, single action only

Ammunition Type: 8mm P.A.K. blanks.

Ammunition Capacity: 5 rounds.

FPS: NA.

Trigger Pull: The trigger on the SM Mod 110 8mm Blank Pistol is single action only so you will need to rack the slide to not only chamber a round but also cock the internal hammer / striker, follow up shots will case the slide to cycle on it own allowing for single action shooting. The trigger is rather nice with just a slight bit of take-up followed by a light release.

Accuracy: NA.

Build Quality: The SM Mod 110 8mm Blank Pistol was made in West Germany sometime back in the Mid 70's so this pistol is 30-40 years old and still looks great. Mine does have some slight pitting on the right side I am assuming from sitting in the box up against the manual which more than likely may have an acidic property to it. Even so this pitting is minor and the gun is in good condition overall. Like most blank pistols much of the gun is made out of pot metal (a zinc alloy) but it does have hardened steel parts where they need to be (Barrel, ejector, hammer, pins, screws and magazine).

Realism: The SM Mod 110 8mm Blank Pistol is not a true replica as far as I can tell is not an actual replica of any real steel semi-auto pistol in production but it does look a bit like the American Derringer LM5. In terms of looking like a gun it looks like what you would expect a small caliber sub compact pistol should look like and all operation is exactly like a semi auto pistol with the exception that the SM Mod 110 only shoots blanks since the barrel is obstructed with a metal rod.

ROHM Guns Available in the: Canada Replica Airguns Store

Pros:

• German made with high quality materials.

• Very small and compact.

• Front firing.

• Nice light and short single action trigger. 

Cons:

• Hard to find one in North America.

• Only holds 5 rounds.

• Slide does not stay back when empty.

Comments:

I really like unique blank guns since they are so hard to locate here in Canada. When I saw this sitting on the table at my local gun show I kind of wondered if someone had accidentally left out a prohibited firearm but once I inspected it I quickly realized it was a blank shooter and decided right there and then I had to have it. I did pay close to $200 for it but to me it is worth it simply because this little blank shooter is a rare find and it was also in really good condition and even came with the original 8mm self defence pepper blanks. The SM Mod 110 8mm Blank Pistol is for sure a blank shooter I will be holding onto for some time...

My Vimeo Table Top Review for the SM Mod 110 8mm Blank Pistol:

Buy ROHM Blank Guns in Canada

This Vimeo Video Preview covers three really nice CO2 Pistols recently added to our Replica Airguns Canada Store. One is a pellet pistol from Gletcher called the Gletcher NGT R which is for the most part the same as the standard 4.5mm Steel shooting NGT but the R model is made to shoot .177 caliber pellets so it also has a rifled barrel. I am expecting pretty decent accuracy with this pistol!

Next up we have another Gletcher Pistol that is actually made by KWC, I have already done a table top review of the KWC version of this same Makarov PM pistol. Gletcher simply has placed their own branding on the KWC version and call it the Gletcher PM 1951 but it is the exact same gun as the Makarov PM but with different markings on the gun.

Last but perhaps the best or at least most anticipated gun I am showing off today is the Umarex S&W M&P40 Full Blowback CO2 BB Pistol. This is a really nice acurate replica of the real steal S&W M&P40 with full licensing and pretty much every part operational like it would be on the .40 caliber version.

Here are some basic Specifications for all of these fine Co2 Airguns...

Gletcher NGT R CO2 Pellet Revolver :

• Ammo Type: .177 caliber pellets.

• Ammo Capacity: 7 Rounds.

• Action: Single and double action Revolver.

• Power Source: 12 gram CO2.

• FPS: 328.

• Weight: 1.54 pounds (700 gram).

• Length: 9 inches.

Gletcher PM 1951 Makarov CO2 Blowback BB Pistol :

• Ammo Type: 4.5mm Steel BB's.

• Ammo Capacity: 16 Rounds.

• Action: Blowback single action semi auto.

• Power Source: 12 gram CO2.

• FPS: 328.

• Weight: 1.63 pounds (740 gram).

• Length: 6.3 inches.

Umarex S&W M&P40 CO2 Blowback BB Pistol :

• Ammo Type: 4.5mm Steel BB's.

• Ammo Capacity: 15 Rounds.

• Action: Blowback single action semi auto.

• Power Source: 12 gram CO2.

• FPS: 310.

• Weight: 1.61 pounds (730 gram).

• Length: 7.75 inches.

Buy Gletcher NGT R CO2 Pellet Revolver in Canada

Buy Gletcher NGT R CO2 Pellet Revolver in the US

Buy Gletcher PM 1951 Makarov CO2 Blowback BB Pistol in Canada

Buy Gletcher PM 1951 Makarov CO2 Blowback BB Pistol in the US

Buy Umarex S&W M&P40 CO2 Blowback BB Pistolin Canada

Buy Umarex S&W M&P40 CO2 Blowback BB Pistol in the US