Entries in Review,AEG

Arcturus AK05 AK AEG Airsoft Rifle Field Test Review

No Comments

It took me a bit to get to this Field Test Reviews done for both the Arcturus AK05 AK AEG and Arcturus AK06 AK AEG Airsoft Rifles but I finally made them! if you want more specifications and details along with closeup video of the Arcturus AK05 then make sure to checkout my Table Tope Review Video for it. In this video I will be testing out the Velocity and then move on to the Accuracy for this AEG Airsoft Rifle in both semi and full auto conducted in the Replica Airguns Sea Can Indoor Airgun Range.

First I placed 5 rounds through my Chronograph shooting .20 gram Airsoft BB’s and I found the Arcturus AK05 AK AEG Airsoft Rifle to be on the higher fps range and it was very consistent with the fastest shot hitting 401 fps and the slowest shot hitting 393. This average an impressive 398 fps which could be a bit hot for some Airsoft Game shooting situations, but perhaps ideal when shooting outdoors at longer ranges.

I then placed a fresh paper target up 30 feet down range and proceeded to shot 10 rounds into the target using a seated and rested shooting position. I followed this up with a spring full of BB’s in full auto in semi auto and full auto getting a bit tighter group in semi auto then I did in full auto but this is generally the case. I did have a bit of trouble with the magazine not loading Airsoft BB’s even though I did tighten the spring fully between testing. Perhaps the magazine needed some break in time or was even defective? Out of the box the Arcturus AK05 AK AEG Airsoft Rifle shot very close to the bullseye but just a tad to the left but not by much. The sights are adjustable for elevation if need be, or you can put a compact red dot sight on the rail for spot on accuracy.

I really did like the Arcturus AK05 AK AEG Airsoft Rifle as it performed very well for me in terms of both power and accuracy other then the magazine acting up. I would most likely add a compact red dot sight on the rail as the built in sights are limited in terms of windage adjustments. You can also see in this video that I had to take off the top dust receiver cover in order to place the battery in it, you will need a very specific and compact battery in order to have it installed and be able to close the top cover. Those two things aside the Arcturus AK05 AK AEG Airsoft Rifle is a great choice if you are looking for a compact and more modernized AK type AEG Airsoft Rifle. Also make sure to watch my Arcturus AK05 AK AEG Airsoft Rifle Field Test Review already available to view on Vimeo!

Categories: 6mm, AEG, Airsoft, Field Test, Full Auto, Review, Rifle, Semi Auto, Vimeo Video Tags: Arcturus, AK05, Acturus AK05

Arcturus AK06 AK AEG Airsoft Rifle Field Test Review.

No Comments

It took me a bit to get to this Field Test Review for the Arcturus AK06 AK AEG Airsoft Rifle but here we are, if you want more specifications and details along with closeup video of the Arcturus AK06 then make sure to checkout my Table Tope Review Video for it. In this video I will be testing out the Velocity and accuracy in both semi and full auto here in the Replica Airguns Sea Can Indoor Airgun Range.

First off I placed 5 rounds through my Chronograph shooting .20 gram Airsoft BB’s and I found the Arcturus AK06 AK AEG Airsoft Rifle to be very consistent with the fastest shot hitting 370 fps and the slowest shot hitting 368, this average an impressive 369 fps which is perfect for most Airsoft Gam shooting situations.

I then placed a fresh paper target up 30 feet down range and proceeded to shot 10 rounds into the target using a seated and rested shooting position. I followed this up with a spring full of shots in full auto with semi auto and full auto getting pretty much the exact same results which I would say to be about a 1.5-2 inch grouping. Out of the box the Arcturus AK06 AK AEG Airsoft Rifle did shot a bit high making me aim about 6 inches lower to achieve hits in the bullseye. Perhaps hope could remedy this as the sights are too adjustable…

I really did like the Arcturus AK06 AK AEG Airsoft Rifle as it performed very well for me in terms of both power and accuracy. I was not a fan of the built in sights as the notch in the back was so low that it barely lined up allowed for it to be inline with the front post sight, I kind of had to guess where the notch was to make it work. I would for sure put a red dot on the rail as the built in sights are pretty much useless. you can also see in this video that I had to take off the top dust receiver cover in order to place my battery in it, you will need a very specific battery in order to have it installed and close the top cover. those two things aside the Arcturus AK06 AK AEG Airsoft Rifle is a really great AK Staled AEG Airsoft Rifle in my books stay tuned for my Arcturus AK05 AK AEG Airsoft Rifle Field Test Review coming soon!

Categories: 6mm, AEG, Airsoft, Field Test, Full Auto, Review, Rifle, Semi Auto, Vimeo Video Tags: Arcturus, Acturus AK06, AK-47

ASG Dan Wesson 2.5 inch Gold CO2 BB Revolver Field Test Review

No Comments

I have made a fair amount of video reviews for the Dan Wesson Line of AIrguns that encompass Table Top and Field Test Reviews on several versions of the Dan Wesson line: BB, Pellet, Airsoft, in a variety of barrel and color choices. It has been a while, so why not make another Review Video to revisit the Dan Wesson Line and so this time here we have the Steel BB version in a 2.5 inch barrel length. As always I will test they CO2 Revolver to find out what the velocity is and how accurate it is shooting at a paper target. Also make sure to watch my Table Top Video for specifications, details and closeup video.

Here we go with the Velocity test! I placed a brand new CO2 in the ASG Dan Wesson 2.5 inch Gold CO2 BB Revolver and shot a cylinder full of 4.5mm steel BB’s that weigh 5.1 grain through my Chronograph. The temperature was average so about room temperature. Only the last 4 of my shots registered on my Chronograph as it was acting up a bit on me at first two shots but I did manage to average 332 fps with the last four. The first two shots would have been a little bit faster had they registered on my chronograph so this may have brought up the average a bit to say around 334…

I then placed a fresh paper target 30 feet down range and proceeded to unload a full 6 round cylinder into it, I was shooting in single action with the hammer cocked back between shots. I was also using a semi rested shooting position with my hands resting on a sand bag up front and seated in the back for stability. Generally speaking even with Steel BB’s I can get close to a 1-2 inch grouping with hess Dan Wessons but this time my 6 shot grouping only produced a 3 inch group? It was probably me as there is always some human error involved and each test can result in different results so keep that in mind. The grouping was well centered out of the box but the ASG Dan Wesson 2.5 inch Gold CO2 BB Revolver does have fully adjustable sights in case yours is a bit off.

It never get’s old loading up the shells with ammo and placing them in the cylinder followed by either quick action shooting or more relaxed and accurate single action shooting, then repeating again and again… The original Dan Wesson line of revelers has been around for a long time now and if I am not mistaken was the first Airgun revolver to use reloadable shells. We now have more refined 715 version of the Dan Wesson which does have some improvement but the original versions still hold strong and are very capable and fun shell loading revolvers that come it a bit lower price tag then the newer 715 versions so no matter which version you get you will have lot of fun shooting and reloading these enjoyable Airguns!

Categories: 4.5mm / .177 cal, BB, CO2, Field Test, Pistol, Review, Revolver, Semi Auto, Vimeo Video Tags: Dan Wesson, ASG, 357

Umarex HK P30 AEG Full Auto Airsoft Pistol Field Test Review

No Comments

I First off this Field Test Shooting Video Review for the Umarex HK P30 AEG Full Auto Airsoft Pistol is going to be more like reviewing a NERF gun, well at least in terms of performance. I do however test it out just like I test all Airsoft Pistols by shooting 5 rounds through the Chronograph to see what the average velocity is in fps. Then I shoot some rounds at a paper target setup 30 feet downrange to see how accurate the Umarex HK P30 AEG Full Auto Airsoft Pistol is. If you want more specification and details along with some nice close up video of the Umarex HK P30, then checkout my Table Top Video for it.

OK, so starting with velocity, I have to say it shot well below the claimed 180fps on the clamshell packaging, keep in mind this is for .12 gram Airsoft BB’s and I was using .20 gram Airsoft BB’s so almost twice as heavy which should mean about half the speed and that’s about what I got. I was able to get an average fps of 95 with my slowest shot hitting 94 fps and my fastest shot hitting 96 fps so very consistently slow :)

What about accuracy? Could the mighty Umarex HK P30 AEG Full Auto Airsoft Pistol at least redeem itself here… Well not really! It was hard to fully determine exactly where my shots where hitting the paper target as it seems 95 fps is not powerful enough to even penetrate the paper. All I could do was put little dings in the paper which are bit hard to make out. My best guess is I should be able to hit a standard sheet of paper at 30 feet away once I figure out where the center point is. I was shooting at the bullseye and hit most shots rather low on the target with several of them being too low to get on the paper. In full auto things did not get much better, but full auto with this little pea shooter is kind of fun, so just keep the selector on full auto all the time… I would!

Getting back to the Umarex HK P30 AEG Full Auto Airsoft Pistol being more like a NERF gun, I say this because it is way too underpowered to use in any Airsoft wars as people probably won’t even know they got hit! But perhaps it is just perfect for indoor NERF type shootouts? I can’t see the Umarex HK P30 doing any type of damage to your surroundings or to yourself but always make sure to wear eye protection when shooting as even an eye lash can feel like murder in the eye let alone a 6mm Airsoft BB. The only real downside I can see to using the Umarex HK P30 AEG Full Auto Airsoft Pistol indoors like a NERF gun would be the cleanup of all the microscopic Airsoft BB’s, you will probably be finding them under furniture and in crazy spots for months afterwards. All in all, the Umarex HK P30 AEG Full Auto Airsoft Pistol may just be perfect for some indoor fun on those rainy days!

Categories: 6mm, AEG, Airsoft, Field Test, Full Auto, Pistol, Review, Semi Auto, Vimeo Video Tags: Umarex, HK P30

KJ Works KP-13 CO2 Blowback Airsoft Pistol Field Test Review

No Comments

The KJ Works KP-13 CO2 Blowback Airsoft Pistol does look a bit like a Glock but don’t be fooled, it is fore sure not a Glock at all. That said it might just make a great training Airsoft pistol if you own a real steel Glock or plan on owning one in the future as it is about the same size and shape and operates similarly to a real Glock. In this video I put it through its paces using my Chronograph to find out the real world velocity and I also place 10 shots on a paper target to see what kind of accuracy I can get from 30 feet away.

Starting with my power or velocity test I put 5 rounds through my Chronograph using standard .20 gram Airsoft Plastic BB’s. I was using a brand new CO2 and the temperature being around 21 degrees Celsius or 70 degrees Fahrenheit, so not too hot or cold. I did only test using the preinstalled internal non-extended barrel so if you do plan on using the longer extend barrel that the KJ Works KP-13 CO2 Blowback Airsoft Pistol comes with, you will more than likely get another 30-40 fps out of this Airsoft Pistol. That said I was able to get an average of 348 fps with my slowest shoot hitting 329 fps and my fastest shot hitting 363 fps. As expected the fastest shot was my first shot out of the Airsoft gun and my slowest shot was my last as the Airgun cooled down.

I then moved on to my accuracy portion of the Field Test for the KJ Works KP-13 CO2 Blowback Airsoft Pistol. It did shoot rather high so I did have to aim at the bottom ring of the target to actually hit closer to the middle. It also shot just a tad to the left but not much so keep that in mind since the sights are not easily adjustable. Hop-up adjustments may lower the rounds a bit but it’s hard to say how much. The KJ Works KP-13 CO2 Blowback Airsoft Pistol did get close to a 1 inch 9 shot grouping (first shot was really high aiming at the bullseye), so that was impressive and the blowback feels solid with a really nice Glock like short and easy trigger.

The KJ Works KP-13 CO2 Blowback Airsoft Pistol is a nice looking and good performing Airsoft Pistol that looks enough like a glock to perhaps appeal to Glock lovers looking for something similar but unique in its own way. After all doesn't everyone already have a Glock, so be a bit different and pick yourself up one of these KJ Works KP-13 CO2 Blowback Airsoft Pistols and be a trend setter!

Categories: 6mm, Airsoft, Blowback, CO2, Field Test, Pistol, Review, Semi Auto, Vimeo Video Tags: KJWorks, KP-13, Glock

Umarex Glock 17 Gen 5 CO2 Blowback Pellet Pistol Field Test Review

No Comments

The Umarex Glock 17 Gen 5 CO2 Blowback Pellet Pistol is a looker for sure replicating the look of a Glock 17 Gen 5 which includes Umarex Glock licensing, lots of metal parts and solid blowback action. That’s all great but does it shoot good? In this Filed Test Shooting video for the Umarex Glock 17 Gen 5 CO2 Blowback Pellet Pistol I put it through its paces using my Chronograph to find out the real world velocity and I also place 10 shots on a paper target to see what kind of accuracy we can get from 30 feet away.

Starting with my power or velocity test I put 5 rounds through my Chronograph using lead pellets that where just over 7 gran. I was all using a brand new CO2 and the temperature being around 21 degrees Celsius or 70 degrees Fahrenheit, so not too hot or cold. Full disclaimer, I was having some feeding problems with the magazine at first but it did seem to sort itself out near the end of this review… All that said, I was able to get an average of 320 fps with my slowest shoot hitting 309 fps and my fastest shot hitting 327 fps, so pretty consistent overall.

I then moved on to my accuracy portion of the Field Test for the Umarex Glock 17 Gen 5 CO2 Blowback Pellet Pistol Luckily the pellet feeding and trigger seemed to work better for me during this portion of the test but the trigger pull was very unpredictable being super hard with some shots and rather easy for others. This is not ideal for getting a good accuracy result, but I did the best I could and surprisingly got around a 3 inch grouping with a very uncooperative trigger. My grouping did hit the target a little bit to the left but was well centered up and down.

I am not a fan of belt fed magazines over all even though Sig Sauer does seem to be able to pull them off better than anyone. Maybe Umarex needs to do a little bit more work here to get better trigger pull consistency and an overall lighter trigger pull. Maybe the Umarex Glock 17 Gen 5 CO2 Blowback Pellet Pistol needs a bit more break in time as it did seem to perform better near the end of my Field Test Review. I would also like to try adding some silicone lubrication ot the magazine as friction seems to be the enemy of belt fed magazines… I am not sure if the Umarex Glock 17 Gen 5 CO2 Blowback Pellet Pistol is a big recommendation for me or not, but it is a really decent CO2 Airgun in many ways. If you're willing to take a bit of a chance that the trigger will improve over time and perhaps a bit of lube will improve things then checkout the Umarex Glock 17 Gen 5 CO2 Blowback Pellet Pistol in our Canada and US online Replica Airguns Stores.

Categories: 4.5mm / .177 cal, Blowback, CO2, Field Test, Pellet, Pistol, Review, Semi Auto, Vimeo Video Tags: Umarex, Glock 17, Gen 5

KJWorks KP-13 CO2 Blowback Airsoft Pistol Table Top Review

No Comments

Type: Blowback CO2 Airsoft Pistol.
Manufacturer: Distributed by KJ Works.
Model: KP-13.
Materials: Metal & Polymer.
Weight: 1.7 pounds (770 grams).
Barrel: 3.7 inches (95mm) metal non-rifled.
Propulsion: CO2 x 1.
Action: Semi auto blowback, SOA trigger.
Ammunition Type: .6mm plastic Airsoft BB’s.
Ammunition Capacity: 24 round drop out full size metal magazine.
FPS: Claimed 366+.

Trigger Pull: The trigger pull on the KJ Works KP-13 CO2 Blowback Airsoft Pistol is what you would expect for a true Single Action Only Trigger which is nice and light. There is a bit of take up but you can feel the point near the back where the release kicks in which is extremely predictable with no play in it. Of course you will need to rack the slide in order to place a round in the breach and fire the first shot, after that the blowback action will do all the work for you.

Accuracy: At this point I have not shot the KJWorks KP-13 CO2 Blowback Airsoft Pistol or done my Field Test Performance Video. I would expect the KJWorks KP-13 to perform like the other KJWork Airsoft Pistols I have reviewed in the past, which generally hits the claimed fps. Keep in mind the claimed fps is with the extended barrel and I more than likely will be using the preinstalled shorter non extendable barrel which will have a slower fps for sure. Accuracy should be decent but we will find out when I make my Field Test Shooting video!

Build Quality: The KJWorks line of Airsoft Guns is know for overall good quality so I expect theKJ Works KP-13 CO2 Blowback Airsoft Pistol to be just the same. From my initial first impressions everything looks really good, fit and finish are excellent and as expected you will find metal parts and polymer parts in all the same places you would find them in a real steel modern semi auto pistol.

Realism: The KJ Works KP-13 CO2 Blowback Airsoft Pistol is not an exact replica of a specific semi auto pistol but yo could say it looks a little bit like a Glock ;) You need to be careful when it comes to Glock as they do not like it when companies copy their guns and rightly so. There is enough differences with the KJ Works KP-13 CO2 Blowback Airsoft Pistol so it should not set off any alarms over at Glock. I do like the two tone tan and black color scheme KJ Works went with for the KP-13 but if you like a more traditional look you can always go with the all black version.

Pros:

  • Metal and Polymer with decent weight and good feel to it.

  • Heavy Full blowback operation.

  • Excellent fit and finish as always with KJWorks pistols.

  • High capacity full size drop out metal magazine that holds the CO2 and 24 rounds.

  • Well hidden safety incorporated into the serial number under the barrel.

  • Working trigger safety.

  • Super easy to see in all conditions fiber optic sight up front.

  • All working components like a real steel Glock styled pistol.

  • Comes with extended barrel for higher velocity and easier import into Canada.

  • Would make a good training weapon if you are use to using Glocks.

  • Like the two tone finish, but can also get it in all black.

  • Easily field strip-able.

Cons:

  • Sights are not adjustable.

  • Would have liked the addition of white outline on the rear sight.

  • Slide spring could be slightly heavier.

Comments:

If you’re looking for a pistol that is similar to a Glock for training purposes but is unique in its own way and doesn’t have to be a Glock, then perhaps the KJ Works KP-13 CO2 Blowback Airsoft Pistol may be for you. I like the fact that it has its own style to it and is not just another Glock or Glock Copy. I also like that the KP-13 comes with a CO2 magazine rather than a Green Gas Magazine which will get you a bit higher velocity and more mag fills before requiring to gas up again. I personally like the two tone version but get what you like best, it’s good to have options!

Categories: 6mm, Airsoft, Blowback, CO2, Comparison, Pistol, Review, Semi Auto, Vimeo Video Tags: KJWorks, KP-13, Glock

Umarex Glock 17 Gen 5 CO2 Blowback Pellet Pistol Table Top Review

No Comments

Type: Blowback CO2 Pellet Pistol.
Manufacturer: Distributed by Umarex.
Model: Glock 17 Gen 5.
Materials: Metal & Polymer.
Weight: 1.6 pounds (725 grams).
Barrel: 4.5 inches metal non-rifled.
Propulsion: CO2 x 1.
Action: Semi auto blowback, DOA trigger.
Ammunition Type: .177 caliber pellets.
Ammunition Capacity: 21 round drop out full size metal magazine.
FPS: Claimed 370.

Trigger Pull: The trigger pull on the Umarex Glock 17 Gen 5 CO2 Blowback Pellet Pistol is what I would describe as closer to a DOA (Double Action Only) trigger. The blowback action does retract the internal hammer/striker which does relieve some of the trigger pull but the trigger is also used to rotate the belt magazine which gives the trigger a kind of friction feel especially right at the end of the pull where the rotation occurs. That said it is not a terrible trigger like some other belt fed Airguns but it is certainly nutlike a standard SAO type Glock trigger.

Accuracy: At this point I have not shot the Umarex Glock 17 Gen 5 CO2 Blowback Pellet Pistol so I can only quote what Umarex is saying in terms of FP2 which is 370. That sounds a bit high for a pellet Airgun but they may be claiming this velocity using a light weight pellets perhaps made out of an alloy rather than lead? I guess we will find out the real world fps using lead pellets and also how accurate it will be when I do my Full Field Test Shooting Video.

Build Quality: The Umarex Glock 17 Gen 5 CO2 Blowback Pellet Pistol like most of the Umarex Glocks is very well made. I am thinking that Glock to allow Umarex to license Glock Pistols hammy have a quality control as part of this license agreement? Either way the Umarex Glock 17 Gen 5 CO2 Blowback Pellet Pistol is a solid and well built Airgun all around with quality material and very good fit and finish.

Realism: The Umarex Glock 17 Gen 5 CO2 Blowback Pellet Pistol in terms of realism as compared to a real steel Glock 19 Gen 5 for sure hits the mark in most categories. It is a bit lighter and you can not field strip it easily, there is also the not so much recessed barrel that is a bit of a giveaway but in terms of most other attributes the Umarex Glock 17 Gen 5 replicates a real Glock… Including the basic looks and feel, the metal slide and polymer frame, the full size drop out metal magazine, the blowback action and most of the working parts including the slide catch release, magazine release and trigger safety.

Pros:

  • Good weight and feel to it, build quality and fit and finish seem very good.

  • Really nice looking and full featured replica of the original Glock 17 Gen 5.

  • Fully Glock licensed via Umarex.

  • Easy to see white dot sights front and back.

  • Working trigger safety.

  • Accessory rail for adding a laser or tactical light.

  • Full size drop out metal magazine that holds the CO2 and .177 caliber pellets.

  • Nice high 21 round capacity.

  • Slide spring feels nice and heavy provide a decent blowback recoil effect.

  • Safety built into the serial number plate area keeps it well hidden.

  • Can see through ejection port when magazine is out.

  • Warning instruction are nice and discreet under trigger guard.

  • 370 claimed fps is good for a CO2 blowback pellet pistol.

Cons:

  • Barrel is not really all that recessed.

  • No way to easily field strip it.

  • Don’t like the clam shell packaging.

  • Trigger is a bit on the heavy side.

Comments:

I think many of us having been waiting for a pellet shooting version of the Glock from Umarex. I am a bit surprised they went with a belt fed version as belt fed magazines tend to be a bit on the heavy trigger pull side. Yes the Umarex Glock 17 Gen 5 CO2 Blowback Pellet Pistol has a stronger trigger pull as compared to a 4.5mm BB or 6mm Airsoft version of the same Umarex gun, as most of these Umarex based Glocks utilize a SAO trigger which is more comparable to a real steel Glock. On the plus side the Pellet version should be a bit more accurate, but we will see how this pans out when I do my comprehensive Field Test Shooting Video for the Umarex Glock 17 Gen 5 CO2 Blowback Pellet Pistol.

Categories: 4.5mm / .177 cal, CO2, Comparison, Pellet, Pistol, Review, Semi Auto, Vimeo Video Tags: Umarex, Glock, Glock 17, Gen 5

ASG Dan Wesson 2.5 inch Gold CO2 BB Revolver Table Top Review

No Comments

Type: BB Revolvers.
Manufacturer: ASG
Model: Dan Wesson 2.5 inch Gold
Materials: Mostly metal.
Weight: 1.9 pounds. (862 grams)
Barrel: Metal non-rifled.
Propulsion: CO2 x 1.
Action: Revolver, single and double action.
Ammunition Type: 4.5mm Steel BB's.
Ammunition Capacity: 6 rounds (removable shells).
FPS: 327

Trigger Pull: The ASG Dan Wesson 2.5 inch Gold CO2 BB Revolver shoots in true modern revolver style offering single and double action. The double action has a bit of friction to it since the cylinder is being rotate during the first part of the trigger pull and there is a spring fed metal gasket between the barrel and the cylinder that creates a seal but does add some resistance to the trigger pull in double action. Single action is much lighter as expected since pulling the hammer back turns the cylinder removing that friction point from the equasion.

.Accuracy: So far I have not done my Filed Test Shooting Video for the ASG Dan Wesson 2.5 inch Gold CO2 BB Revolver, but I plan to in the near future as a revisit since I have made a lot of similar Field Test Videos for the Dan Wesson line of products in 4.5mm Steel BB and 6mm Airsoft, here is a link to me shooting the 8 inch a while back in my old setup. Wow, this one goes back to 2014 almost 10 years ago!

Build Quality: The ASG Dan Wesson 2.5 inch Gold CO2 BB Revolver overall is really well built with good weight to it and a nice fit and finish, I do like the Gold version in this 2.5 inch version. It is almost all metal with the exception of the grips which are made of a semi hard plastic. One beef I have with the original ASG Dan Wesson line of revolvers are how the grips slide back to access the CO2, closing them can be a bit of a chore as they can come off their track super easily. The other complaint I hear about them is the play in the trigger and hammer side to side.

Realism: The ASG Dan Wesson 2.5 inch Gold CO2 BB Revolver like all the other ASG Dan Wesson Revolvers is very realistic with its realistic pop out cylinder and 6 removable shells you can reuse and load up for numerous rounds of shooting. You can also buy additional shells and have them preloaded and ready to go in the Speed loader to speed things up. Two things about the ASG Dan Wesson 2.5 inch Gold CO2 BB Revolver that take away a bit from the realism would be the non recessed barrel and the rather large space in front of the hammer. A real steel Dan Wesson or even most revolvers do not have this large space. I believe they did this to allow for the internal valve system. The newer Dan Wesson 715 however was designed with a smaller space in front of the hammer.

Pros:

  • It's a revolver with actual shells! Gives you the feeling of a real 6 shooter.

  • Almost all metal design with good weight and feel.

  • Lots of detail in this gun, very well made, fit and finish is very good.

  • Good power and good accuracy. (going off of already done older reviews)

  • Fully adjustable rear sight for windage and elevation.

  • Can add the included accessory rail for more options (optical or red dot sight…).

  • Dan Wesson licensed via ASG.

  • Gold finish is unique. (Gold is the Best!)

  • Moulded and textured pistol grips.

  • Grips fully hide CO2 screw.

  • Can shoot in both double and single action for action shooting or more accurate shot placement.

Cons:

  • Plastic CO2 screw tab.

  • Plastic grip setup can be a bit awkward to close.

  • 2.5 inch does not have the recessed barrel.

  • Hammer and trigger are a bit sloppy compared to 715 version.

Comments:

It’s been a while since I reviewed one of the first generation ASG Dan Wesson Revolvers and the ASG Dan Wesson 2.5 inch Gold CO2 BB Revolver does bring back some memories for me going back almost a decade. If I’m not mistaken this revolver was the first one to implement actual removable and reloadable shells making Airgun Replica Revolvers a lot more interesting and realistic! I do kind of prefer the newer 715 version as they are even beefier than the original ASG Dan Wessons and ASG has fixed the sloppy hammer and trigger along with the space in front of the hammer has been reduce making the 715 even that much more realistic.

Watch my Vimeo Video Table Top Review for the Dan Wesson 2.5 Inch Gold BB Revolver:

Categories: 4.5mm / .177 cal, BB, CO2, Pistol, Review, Revolver, Vimeo Video Tags: Dan Wesson, ASG, 357

Umarex HK P30 AEG Full Auto Airsoft Pistol Table Top Review

No Comments

Type: BB air pistol.
Manufacturer: Umarex USA.
Model: HK P30
Materials: All pastic outer shell.
Weight: .5 pounds (227 grams)
Barrel: Metal non-rifled 4.25 inches (106mm).
Total Length: 7 inches (178mm)
Propulsion: CO2 x 1.
Action: Semi & full auto blowback, single action only.
Ammunition Type: 6mm Plastic Airsoft BB's.
Ammunition Capacity: 16 round plastic curved stick magazine x2.
FPS: 180
Rate of fire: 200 shots/min.

Trigger Pull: The trigger on the Umarex HK P30 AEG Full Auto Airsoft Pistol is electric as it is an AEG Pistol that requires batteries to operate. The trigger is basically an ON/Off switch that activates the blowback which also seems to create the pressure to propel an Airsoft BB. Mind you not all that fast but fast enough for perhaps a more safe indoor/basement type Airsoft war? Getting back to the trigger pull I would say it is light but on the ing side for an AEG.

Accuracy: You will have to stay posted for my proper Field Test Shooting Video for the Umarex HK P30 AEG Full Auto Airsoft Pistol. That said I did pop off a magazine of BB’s (16 rounds), some in semi auto and some in full auto. Do not expect this Airsoft pistol to be all that powerful as it can barely penetrate a paper target. I was expecting the cycle rate of full auto to feel slower than it actually shot so that’s a good thing! I see this as almost an alternative to a nerf gun but using Airsoft BB’s. Do this at your own risk and please use proper eye protection. I can not comment too much on accuracy as I was just pointing and shooting to get a basic feel for the gun.

Build Quality: The Umarex HK P30 AEG Full Auto Airsoft Pistol is a low cost all plastic Airsoft pistol which kind of says it all. Being super light weight means if you drop it, chances are it will be fine because it is so light weight. Fit and finish are decent but without seeing what’s inside I can only guess at how long it will last.

Realism: The Umarex HK P30 AEG Full Auto Airsoft Pistol is a true licensed replica via Umarex. It is about the right shape and size as a real HK P30 and other than the orange tip could fool most people unless really close up to it and of course holding it. It also has a kind of out of place grip safety on the front which is not an HK attribute. Being an AEG with batteries in the grip there is no full size magazine and again as it is all plastic it does not have nearly the same weight as a real HK P30. The only working mechanical parts are essentially the trigger, grip safety and selector switch in the trigger area.

Available From: The Canada and US Replica Airgun Stores.

Pros:

  • Drop out stick mags are nice for continuous shooting without having to reload as often.

  • Has a rail for accessories.

  • Working slide with blowback action.

  • Shoots in both semi and full auto selectable.

  • No CO2 so perhaps better in colder weather being an AEG, lower cost to operate!

  • Walther licensing via Umarex.

  • Grip safety to help stop unwanted accidental shots.

  • Serial number on receiver.

  • Warning instructions are non-obtrusive.

  • Trigger is nice and light being an AEG.

Cons:

  • Is very light weight being almost all plastic.

  • Low claimed fps and slow full auto cycle rate.

  • Orange tip.

  • Sights are all black, harder to see on dark objects

Comments:

The Umarex HK P30 AEG Full Auto Airsoft Pistol is a rather different sort of beast! On one hand it is not what you would expect to see someone using in an Airsoft game but I really don’t think that’s what it is meant for anyway. It’s really just a fun gun for plinking without having to worry to much about safety as if you do something stupid, the consequences will not be too sever! I would say it could possibly be used as an alternate to using a Nerf gun for fun little backyard squishes or shooting indoors. The Umarex HK P30 AEG Full Auto Airsoft Pistol is not for everyone but I am guessing it could be a lot of fun when used in the right situations.

Watch my Table Top Video Review for the Umarex HK P30 AEG Full Auto Airsoft Pistol:

Categories: 6mm, AEG, Airsoft, Blowback, Full Auto, Pistol, Review, Semi Auto, Vimeo Video Tags: HK P30, Umarex

Arcturus AR06 - NY03CB AEG Airsoft Rifles Table Top Review

No Comments

Type: Airsoft Rifle.
Manufacturer: Acturus.
Model: AR06 & NY03CB.
Materials: Mostly all Metal.
Weight: 5.6/4.9 pounds (2.5/2.2 kilograms).
Length: 27.4-30.7/31.7-35 inches (695-780/805-890mm)
Barrel Length: 11/14.6 inch (280/370mm) inner 6.02mm tight bore non rifled.
Propulsion: AEG (with Deans Connectors).
Action: Semi & Full Auto SAO.
Ammunition Type: 6mm Airsoft BB's.
Ammunition Capacity: Hi Cap/Mid Cap - 550/135
FPS: 380-400fps.

Trigger Pull: The trigger pull on the Arcturus AR06 - NY03CB AEG Airsoft Rifles like other AEG Rifles is not mechanical as they are essentially electrical driven so basically the trigger is an on/off switch that is closest in feel to a single action only trigger since it is light and short. You will notice a slight delay between pressing the trigger and the actual round being fired since the trigger activates a motor which first pulls the air spring back. Once the spring is fully drawn back it releases and compresses the air which then propelled the 6mm Airsoft BB. The higher voltage battery you use like an 11.1 volt will shorten the delay as the motor will spin faster and pull back the spring quicker allowing for less noticeable delay and also a higher rate of full auto fire which in this rifle is very noticeable.

Accuracy: I have not Field Test Reviewed either the Arcturus AR06 - NY03CB AEG Airsoft Rifles or even tried them out yet. I hope to get to my Field Test Shooting Video for both of them later next week, until then we can assume they will shoot similar to most other AEG rifles with tighter bore barrels. I am expecting at least a 2 inch grouping at 30 feet down range in semi auto. In terms of velocity the test paper which they come with claims around 390+fps.

Build Quality: The Arcturus AR06 is a mostly metal with a full metal receiver while the NY03CB has a polymer or plastic receiver which from what I can tell only other components being plastic would be the pistol grips and rear stock. other metal parts on both AR type Airsoft Rifles would be the rail setup, the barrel, the charging handle, the buffer tube, the dust cover, the trigger, the selector switch, the magazine release and bolt release. Fit and finish for both guns is very good.

Realism: The Arcturus AR06 - NY03CB AEG Airsoft Rifles are based on the AR platform with both versions looking the part of a real steel AR. They do come with the removable orange tips installed but they also come with black flash hiders so you can easily switch them out adding to the realism. The metal receiver on the AR06 does give it a bit more weight but even the NY03CB has a decent weight and solid feel to it. Most of the controls work just like a real steel AR including the charging handle, bolt release, selector switch and magazine release.

Pros:

  • Two versions to meat your budget, both great options.

  • Quality components throughout both versions. Only real difference is nylon fiber receiver vs metal receiver and slight upgrade motor on AR06 version from Long Type to Long Type 19k torque motor on AR06.

  • Have been quality control inspected including 5 round recorded fps test with .20 gram Airsoft BB’s.

  • Both  have a functioning bolt catch.

  • Both come with Quick release two position fully adjustable pop-up sights.

  • Both come with additional black flash hiders.

  • Lots of rial mounting options in Picatinny and M-LOK.

  • 6 position adjustable rear stocks.

  • Easy access to motor for any possible trouble shooting you may need to do.

  • Additional grip plate option.

  • Ambidextrous controls and ambidextrous sling mounting points (QD on AR06).

  • Two magazines come with AR06 (Mid Cap and High Cap).

Cons:

  • Limited battery options as area is small.

  • Kind of need a tool to remove rear stock for battery access. (Could change the rear stock)

  • Mystery accessory baffles me and not mentioned in the manual.

Comments:

Like the AK series of Acturus AEG Airpot Rifles, the Arcturus AR06 - NY03CB AEG are good value for the money with the AR06 offering a slightly higher premium over the lower cost NY03CB. But don’t let the lower price fool you into thinking you are getting a sub-standard product as both versions are built with many of the same components. I personally like the more compact look of the Arcturus AR06 AEG Airsoft Rifle but then again the price of the NY03CB AEG Airsoft Rifle is hard to ignore. Either way you can’t go too wrong so make your pick and enjoy owning one of them.

My Table Top Video of the Acturus AR06 - NY03CB AR AEG Airsoft Rifles:

Categories: 6mm, AEG, Airsoft, Comparison, Full Auto, Review, Rifle, Semi Auto, Vimeo Video Tags: Acturus, Acturus AR06, AR06, Acturus NY03CB, NY03CB

Umarex T4E HDB .68 Caliber Paintball Shotgun Table Top Review

No Comments

Type: Paintball Shotgun.
Manufacturer: Umarex - T4E.
Model: Umarex T4E HDB.
Materials: Metal & Polymer.
Weight: 5.52 pounds (2.5 kg).
Barrel: 18.5 inches (470.5mm) Metal smooth bore.
Power Source: 1x12 gram CO2.
Action: Semi Auto DOA with Internal Magazine.
Ammo Type: .68 Caliber Paintball or Rubber Ball.
Ammo Capacity: 16 Rounds.
FPS: 220 claimed

Trigger Pull: The trigger pull on Umarex T4E HDB .68 Caliber Paintball Shotgun is basically a Double Action Only Trigger as there is no blowback or way in which to preload a hammer or striker system. So basically your finger does all the work so the trigger pull is I would say about medium length and about medium pull. It does works just fine for fairly rapid follow up shooting. Each pull of the trigger also extends a rear breach-like tube that seals off the CO2 from the internal magazine or there would be a lot of CO2 leakage.

Accuracy: Normally I do not get the chance to perform the Field Test before making my Table Tope Video Review but with the Umarex T4E HDB .68 Caliber Paintball Shotgun, I did it the other way around so I do have performance metrics I can share with you, at least summarized. I suggest watching my Full Field Test Shooting Video Review for the Umarex T4E HDB .68 Caliber Paintball Shotgun for a the full breakdown. In summary, the Umarex T4E HDB .68 Caliber Paintball Shotgun shot a bit low on the target but had a decent grouping of I would say around 4-6 inches which is really good for a Paintball Gun. In terms of power my Chronograph results shooting 5 rounds produced an average of 176fps but the temperature was not super warm so in warmer conditions you can expect this to go up a bit, I would say 200fps is realistic.

Build Quality: The build quality of the Umarex T4E HDB .68 Caliber Paintball Shotgun is really good for the lower price of this unit compared to other higher priced T4E products, you will get a pretty much all plastic outer shell. That said there is still a fair amount of metal in this PaintBall Shotgun including the barrel, internal magazine, sights, trigger, sling mounts and some internal parts. All in all the Umarex T4E HDB .68 Caliber Paintball Shotgun has a good weight and feel to it with nice fit and finish.

Realism: The Umarex T4E HDB .68 Caliber Paintball Shotgun as far as I know is not an exact replica of any specific Shotgun but it does look like what you would expect to see from a Pistol Grip Tactical Styled Shotgun. In terms of mechanical working parts everything does what it supposed to do and works as expected.

Purchase it from the Canada Replica Airguns Store or the US Replica Airguns Store

Pros:

  • Accuracy was really good, probably my tightest grouping so far to date with a Paintball Gun shooting at 30 feet away.

  • Lots of mounting option for accessories like a tac light, laser or other sighting option with it’s top and side picatinny rail and M-LOK setup.

  • Quick CO2 pierce system so you can leave a CO2 in it ready to go any time with no worries about CO2 leaking out over time.

  • Simple to use Cross Bolt Safety.

  • Nice high capacity super easy to load 16 round magazine.

  • Ambidextrous sling mountain points.

  • Low cost for what you get compared to other Umarex/T4E products.

  • Build quality feels pretty good considering it is a much lower cost than other T4E rifles/shotguns.

  • Looks very intimidating.

Cons:

  • Mostly plastic external build.

  • Sights are not adjustable.

  • Will not get lots of shots per single CO2.

  • No rear stock so will not be as accurate using a non rested shooting posting.

Comments:

The Umarex T4E HDB .68 Caliber Paintball Shotgun is a well built and decent performing Paintball Shotgun and for the price you do get a lot of gun for your money. In some ways it even outperforms the HDX in my books including lower price, ease to load, quicker follow shots being semi auto, more compact size and even accuracy was better with the Umarex T4E HDB .68 Caliber Paintball Shotgun. So if you’re on a budget, don’t feel like you are compromising at all here, you are getting a really good Paintball Shotgun solution!

Categories: .68 cal, CO2, Paintball, Pistol, Review, Rifle, Semi Auto, Vimeo Video Tags: Umarex, T4E HDB, T4E

Umarex S&W M&P 9L Blowback CO2 Airsoft Pistol Field Test Review

No Comments

Yet another Field Test Shooting Video performed in the Replica Airguns Indoor Airgun Sea Can Shooting Range! In this Field Test I shoot the Umarex S&W M&P 9L Blowback CO2 Airsoft Pistol to see what kind of velocity and accuracy it has shooting .20 gram Airsoft BB’s with a brand new CO2 cartridge. If you are interested in the specifications and details along with some more close up video than watch my Table Top Review Video here.

Like pretty much every Field Test Shooting video I first perform the Chronograph Velocity Test since my CO2 is the most fresh at this point. I didn’t check the temperature in the Sea Can but I generally keep it around 20-22 degrees Celsius which is 68-72 Fahrenheit. I was a bit amazed at the high velocity of the Umarex S&W M&P 9L Blowback CO2 Airsoft Pistol in my testing as the claimed fps was 410 and most guns don’t live up to their claims exactly. The Umarex S&W M&P 9L Blowback CO2 Airsoft Pistol shooting 5 shots through the Chronograph averaged 431 fps with the slowest shot at 427fps and the fastest shot hitting 439fps so consistency was good!

Next I setup a fresh paper target 30 feet downrange and proceeded to place 10 rounds in it using a rested shooting position with my hands resting on a sandbag up front and seated in the back. Watch the video to see what actually happened but in a nut shell the Umarex S&W M&P 9L Blowback CO2 Airsoft Pistol shoots really high at 30 feet, at least 10 inches. So I did need to figure out where it was shooting before I actually got rounds on the paper. It was a bit hard to figure out the precise 10 shot grouping since some rounds may have even shot over the target when I was aiming at the bottom of the target but my best estimate is around 3-4 inches.

Other than the rather high shot placement which may be adjustable to some degree by adjusting the hop-up,I would say the Umarex S&W M&P 9L Blowback CO2 Airsoft Pistol is a very nice gun. The power is really good and may even be a bit much for close quarters indoor games but outdoors where you are shooting longer ranges it should perform well in these conditions. The blowback is very strong and the trigger feels good. If you don’t mind adjusting your shooting point a bit then the Umarex S&W M&P 9L Blowback CO2 Airsoft Pistol would be a great choice as your sidearm.

Categories: 6mm, Airsoft, Blowback, CO2, Field Test, Pistol, Review, Semi Auto, Vimeo Video Tags: Umarex, M&P 9L, S&W M&P

Umarex T4E HDB .68 Caliber Paintball Shotgun Field Test Review

No Comments

In this Field Test Shooting Video I test out the Umarex T4E HDB .68 Caliber Paintball Shotgun to see what the actual fps is and what kind of accuracy we can get out of these .68 Caliber Rubber balls at 30 feet down range. I have not done a Table Top Video just yet for the Umarex T4E HDB .68 Caliber Paintball Shotgun so stay posted for that upcoming video so stay posted for that, in the meantime you can watch my Preview Videos where I do show it up and close and go over some main specifications.

Starting with the velocity portion of this video I used .68 caliber rubber balls which are not super heavy and not made out of a very hard rubber as you can squish them with your fingers fairly easily. I put 5 rounds through my chronograph after loading a pair of 12 gram CO2 cartriges into the CO2 chamber. My results averaged 176fps which may seem slower than expected but they did hit my target pretty hard pulling the paper in with them. Each round was fairly consistent ranging from 167 to 182 fps trailing off a bit after each shot which is expected.

Moving on to the accuracy portion for the Umarex T4E HDB .68 Caliber Paintball Shotgun, I proceeded to shoot around 10 rounds into my fresh paper target setup 30 feet down range. My target is basically an 8.5 x 11 sheet of paper and my goal was ot get all my shots onto the paper which I easily managed. I was impressed with the grouping from the Umarex T4E HDB .68 Caliber Paintball Shotgun as it performed better than most Paintball guns using rubber balls. The shot placement was a bit lower than I was aiming but all the rounds where within I would say 4-5 inches of each other with no real outliers in the grouping.

All in all the Umarex T4E HDB .68 Caliber Paintball Shotgun performed better than I was expecting, I bit more fps would be nice but the rubber balls do hit the paper with a fair amount of energy, I would for sure not want to get hit by one at close range with light clothing on. The accuracy again was really good for a a paintball rifle and this being one of the lower cost Umarex T4E rifle/shotgun based products it performed as good if not better than much higher priced versions. If you’re looking for a fun Paintball Rifle that won’t break the bank and has a good feature set then pick one up for us!

Categories: .68 cal, CO2, Field Test, Review, Rifle, Semi Auto, Vimeo Video Tags: Umarex, T4E, HDB

Umarex HK P30 - T4E HDB - ASG Dan Wesson 2.5 - KJWorks KP13 Update Preview

No Comments

In this Preview Review Video I take a look at 4 newer products now in our Replica Airguns Online Store. One is a 4.5mm Steel BB Revolver, two are 6mm Airsoft Pistols and one is a .68 caliber Paintball Shotgun.

The first item I take look at in this video is the Umarex HK30 AEG Airsoft Pistol, this product is pretty entry level with analyst all plastic build and is very light to hold. It does however shoot in both semi and full auto since it is an AEG Airsfto Pistol (not many of them out there). The fps is rather low at a claimed fps at just under 200, the Umarex HK30 AEG Airsoft Pistol also comes with two 16 round remove; plastic magazines. Who knows, maybe it will be fun?

Next I take a look at the ASG Dan Wesson 2.5 inch 4.5mm Steel BB Gold Revolver. This is a CO2 powered shell loading BB revolver very much like similar ones I have reviewed in the past but in Gold finish. Will the gold finishes make it perform better, well I guess we better find out!

I then take a look at a “Glock Like” CO2 Blowback Airsoft Pistol for KJWorks called the KP13. It has a full size drop out metal magazine that holds the CO2 along with 24 rounds of 6mm Airsoft BB’s. The KJWorks KP-13 has a metal slide, metal magazine and polymer frame with a velocity over 360fps using the included barrel extension.

Last but perhaps the most interesting for me is the Umarex T4E HDB which is a lower cost Paintball/Rubber Ball Shotgun which could possibly be used for home protection? The T4E HDB is a mostly plastic constructed rifle with decent weight to it and uses an internal spring fed 16 round magazine. You will find all kinds of mounting points for accessories and for a sling on the Umarex T4E HDB and again at much lower cost than similar T4E rifle based Paintball/Rubber ball Airguns.

Categories: .68 cal, 4.5mm / .177 cal, 6mm, AEG, Airsoft, BB, Blowback, CO2, Full Auto, Pistol, Review, Revolver, Rifle, Semi Auto, Vimeo Video Tags: Umarex, T4E, HDB, T4E HDB, HK P30, H&K, KJWorks, KP-13, ASG, Dan Wesson

Acturus AK05 AK AEG Airsoft Rifle Table Top Review

No Comments

Type: Airsoft Rifle.
Manufacturer: Acturus.
Model: AK05.
Materials: Mostly all Metal.
Weight: 8.2 pounds (3.7 kilograms).
Length: 31.1 inches (790mm)
Barrel Length: 11 inch (280mm) inner 6.02mm tight bore non rifled.
Propulsion: AEG (with Deans Connectors).
Action: Semi & Full Auto SAO.
Ammunition Type: 6mm Airsoft BB's.
Ammunition Capacity: Hi Cap/Mid Cap - 550/135
FPS: 380-400fps.

Trigger Pull: The trigger pull on the Acturus AK05 AK AEG Airsoft Rifle like other AEG Rifles is not mechanical as it is essentially electrical driven so basically it is an on/off switch that is closest in feel to a single action only trigger since it is light and short. You will notice a slight delay between pressing the trigger and the actual round being fired since the trigger activates a motor which first pulls the air spring back. Once the spring is fully drawn back it releases and compresses the air which then propelled the 6mm Airsoft BB. The higher voltage battery you use like an 11.1 volt will shorten the delay as the motor will spin faster and pull back the spring quicker allowing for less noticeable delay and also a higher rate of full auto fire which in this rifle is very noticeable.

Accuracy: I have not Field Test Reviewed the Acturus AK05 AK AEG Airsoft Rifle or even tried it out yet. I hope to get to my Field Test Shooting Video for the AK05 later next week, until then we can assume it will shoot similar to most other AEG rifles with tighter bore barrels. I am expecting at least a 2 inch grouping at 30 feet down range in semi auto. In terms of velocity the test paper work it comes with claims around 390+fps.

Build Quality: The Acturus AK05 AK AEG Airsoft Rifle is almost all metal in design with from what I can tell only the pistol grip being plastic. The receiver and top dust cover are both hardened steel with the receiver made out of stamped steel just like areal AK. The AK05 is nice and heavy for its size and the fit and finishes is very good all around. Internal parts are all of high quality too.

Realism: The Acturus AK05 AK AEG Airsoft Rifle is based on the AK platform with this version being a more compact and tactical model. Externally it looks the part for sure, holding it in your hands it feels the part too. As expected the insides are all Airsoft but you would need ot take the dust cover off or pull back the charging handle to figure this out. Again the Acturus AK05 AK AEG Airsoft Rifle is an almost all metal Airsoft Gun with an actual stamped steel receiver and steel dust cover, it’s hard to get much more realistic looking and feeling than that.

Pros:

  • Lots of mounting options: Picatinny rails, M-LOK, AK Side Rail.

  • Semi and full auto adjustable.

  • 5 position adjustable rear stock.

  • Mostly metal construction and lots of actual steel including the receiver and dust cover.

  • Lots of weight to it at 8.2 pounds, feels awesome to hold.

  • Comes with two magazines, one Hi Cap and one Mid Cap.

  • Comes with a secondary all black squared off flash hider.

  • On the fly adjustable rear sight for elevation.

  • Quick change spring system.

  • Easy to get to and adjust rotary hop-up adjustment.

  • Should be good for longer range shooting with nice high claimed fps.

Cons:

  • Will need a very specific battery type, thin and long.

  • Rear sight only adjustable for windage and not elevation.

  • May even be a bit heavy for all day use.

Comments:

The Acturus AK05 AK AEG Airsoft Rifle along with the other Acturus AK Airsoft Rifles is in my opinion one of the nicest AEG AK based Airsoft rifles you can get, at least in the mid price ranges. Being all metal with actual stamped steel parts really makes the AK05 feel realistic and of high quality. If you’re looking for something with a bit more heft than the Acturus AK06 that has a more useful rear stock at least in terms of adjustability and don’t mind giving up some of the compact features of the AK06 then perhaps the AK05 is more for you. IN my opinion the Acturus AK05 AK AEG Airsoft Rifle is a great combination of quality, size and features, hopefully my upcoming Field Test Shooting Review backs up the performance aspect and we can add that to the list.

Categories: 6mm, AEG, Airsoft, Full Auto, Review, Rifle, Semi Auto, Vimeo Video Tags: Acturus, Acturus AK05, AK05

Acturus AK06 AK AEG Airsoft Rifle Table Top Review.

No Comments

Type: Airsoft Rifle.
Manufacturer: Acturus.
Model: AK06.
Materials: Mostly all Metal.
Weight: 6 pounds (2.7 kilograms).
Length: Folded/unfolded 18.9/27.4 inches (480/695mm)
Barrel Length: 9.8 inch (250mm) inner 6.02mm tight bore non rifled.
Propulsion: AEG (with Deans Connectors).
Action: Semi & Full Auto SAO.
Ammunition Type: 6mm Airsoft BB's.
Ammunition Capacity: Hi Cap/Mid Cap - 550/135
FPS: 380-400fps.

Trigger Pull: The trigger pull on the Acturus AK06 AK AEG Airsoft Rifle like other AEG Rifles is not mechanical as it is essentially electrical driven so basically it is an on/off switch that is closest in feel to a single action only trigger since it is light and short. You will notice a slight delay between pressing the trigger and the actual round being fired since the trigger activates a motor which first pulls the air spring back. Once the spring is fully drawn back it releases and compresses the air which then propelled the 6mm Airsoft BB. The higher voltage battery you use like an 11.1 volt will shorten the delay as the motor will spin faster and pull back the spring quicker allowing for less noticeable delay and also a higher rate of full auto fire which in this rifle is very noticeable.

Accuracy: I have not Field Test Reviewed the Acturus AK06 AK AEG Airsoft Rifle or even tried it out yet. I hope to get to my Field Test Shooting Video for the AK06 later next week, until then we can assume it will shoot similar to most other AEG rifles with tighter bore barrels. I am expecting at least a 2 inch grouping at 30 feet down range in semi auto. In terms of velocity the test paper work it comes with claims around 370fps.

Build Quality: The Acturus AK06 AK AEG Airsoft Rifle is almost all metal in design with from what I can tell only the pistol grip being plastic. The receiver and top dust cover are both hardened steel with the receiver made out of stamped steel just like areal AK. The AK06 is nice and heavy for its size and the fit and finishes is very good all around. Internal parts are all of high quality too.

Realism: The Acturus AK06 AK AEG Airsoft Rifle is based on the AK platform with this version being a more compact and tactical model. Externally it looks the part for sure, holding it in your hands it feels the part too. As expected the insides are all Airsoft but you would need ot take the dust cover off or pull back the charging handle to figure this out. Again the Acturus AK06 AK AEG Airsoft Rifle is an almost all metal Airsoft Gun with an actual stamped steel receiver and steel dust cover, it’s hard to get much more realistic looking and feeling than that.

Pros:

  • Lots of mounting options: Picatinny rails, M-LOK, AK/SVD Side Rail.

  • Semi and full auto selectable.

  • All metal folding rear stock.

  • Mostly metal construction and lots of actual steel including the receiver and dust cover.

  • Lots of weight to it at 6 pounds, feels awesome to hold.

  • Comes with two magazines, one Hi Cap and one Mid Cap.

  • Comes with a secondary all black squared off flash hider.

  • Super compact design.

  • Quick change spring system.

  • Easy to get to and adjust rotary hop-up adjustment.

  • Should be good for longer range shooting with nice high claimed fps.

Cons:

  • Will need a very specific battery type, thin and long.

  • Sights are non adjustable.

  • Folding type rear stock not adjustable for pull length.

Comments:

The Acturus AK06 AK AEG Airsoft Rifle along with the other Acturus AK Airsoft Rifles is in my opinion one of the nicest AEG AK based Airsoft rifles you can get, at least in the mid price ranges. Being all metal with actual stamped steel parts really makes the AK06 feel realistic and of high quality. I also like the compact tactical features of the Acturus AK06 AK AEG Airsoft Rifle making it easy to put in a backpack but not too heavy to lug around all day long. The Acturus AK06 AK AEG Airsoft Rifle also has a decent velocity and fairly fast rate of fire especially when using a higher voltage battery so you can expect excellent performance even from such a small compact AEG Airsoft Rifle.

My Table Top Video of the Acturus AK06 AK AEG Airsoft Rifle:

Categories: 6mm, AEG, Airsoft, Full Auto, Review, Rifle, Semi Auto, Vimeo Video Tags: Acturus, AK06, Acturus AK06

Arcturus AEG Airsoft Intro Preview Unboxing Video Review

No Comments

In this Preview Unboxing Video I Take a look at 4 new Airsoft products from Arcturus all of them being AEG Airsoft Rifles with two based on the AK platform and the other two based on the AR platform. Three of the AEG Airsoft Rifles are mostly metal while I also feature a lower cost version with a Nylon Fiber Polymer receiver. All of these Replica AEG Airsoft Rifles are very good quality but you will get all metal (mostly steel and aluminum) build and a Hi-Cap and Mid-Cap magazine with the higher cost versions.

Arcturus AK05 AK AEG Airsoft Rifle:

  • Type: Airsoft AEG.

  • Manufacturer: Arcturus.

  • Caliber: 6mm plastic Airsoft BB's.

  • FPS Range: 380-400.

  • Magazine Capacity: 550rd Hi-Capacity and 30/135rd Mid-Capacity.

  • Thread Direction: 14mm Negative.

  • Gearbox: Version 3 Full Metal w/ Quick Change Spring, Fully Upgradeable.

  • Motor: Short Type.

  • Fire Modes: Semi/Full-Auto, Safety.

  • Battery: 9.6v Small Stick Type or 7.4v stick LiPo recommended.

  • Battery Location: Wired to dust cover with small Tamiya connector.

  • Hopup: Yes, Adjustable.

  • Inner Barrel: 280mm / 6.02mm.

  • Length: 790mm - 875mm, Adjustable.

  • Weight: 3730g.

  • Package Includes: Gun, Hi-Cap Magazine, Mid-Cap Magazine.

Arcturus AK06 AK AEG Airsoft Rifle:

  • Type: Airsoft AEG.

  • Manufacturer: Arcturus.

  • Caliber: 6mm plastic Airsoft BB's

  • FPS Range: 380-400.

  • Magazine Capacity: 550rd Hi-Capacity and 30,135rd Mid-Capacity.

  • Thread Direction: 14mm Negative.

  • Gearbox: Version 3 Full Metal w/ Quick Change Spring, Fully Upgradeable.

  • Motor: Short Type.

  • Fire Modes: Semi/Full-Auto, Safety.

  • Battery: 9.6v Small Stick Type or 7.4v stick LiPo recommended.

  • Battery Location: Wired to dust cover with small Tamiya connector.

  • Hopup: Yes, Adjustable.

  • Inner Barrel: 250mm / 6.02mm.

  • Length: 480mm, 695mm (Folded, Unfolded).

  • Weight: 2730g.

  • Package Includes: Gun, Hi-Cap Magazine, Mid-Cap Magazine.

Arcturus AR06 AR AEG Airsoft Rifle:

  • Type: Airsoft AEG.

  • Manufacturer: Arcturus.

  • Caliber: 6mm plastic Airsoft BB's

  • FPS Range: 380-400.

  • Magazine Capacity: 320rd Hi-Capacity and 130rd Mid-Capacity.

  • Thread Direction: 14mm Negative.

  • Gearbox: Version 2 w/ Quick Change Spring, Fully Upgradeable.

  • Motor: Long Type, 19k torque motor.

  • Fire Modes: Semi/Full-Auto, Safety.

  • Battery: 7.4v stick LiPo recommended.

  • Battery Location: Wired to buffer tube with small Tamiya connector.

  • Hopup: Yes, Adjustable.

  • Inner Barrel: 280mm / 6.02mm.

  • Length: 695mm - 780mm, Adjustable.

  • Weight: 2520g.

  • Package Includes: Gun, Hi-Cap Magazine, Mid-Cap Magazine.

Arcturus NY03CB AR AEG Airsoft Rifle:

  • Type: Airsoft AEG.

  • Manufacturer: Arcturus.

  • Caliber: 6mm plastic Airsoft BB's

  • FPS Range: 380-400.

  • Magazine Capacity: 330rd Hi-Capacity.

  • Thread Direction: 14mm Negative.

  • Gearbox: Version 2 Gearbox w/ Quick change spring system, Fully upgradeable.

  • Motor: Long Type.

  • Fire Modes: Semi/Full-Auto, Safety.

  • Battery: 7.4v stick LiPo recommended.

  • Battery Location: Wired to buffer tube w/ Deans Connector.

  • Hopup: Yes, Adjustable.

  • Inner Barrel: 370mm~ / 6.02mm.

  • Length: 805mm - 890mm, Adjustable.

  • Weight: 2020g.

  • Package Includes: Gun, Hi-Cap Magazine.

Categories: 6mm, AEG, Airsoft, Comparison, Full Auto, Review, Rifle, Semi Auto, Vimeo Video Tags: AK05, AK06, AR06, NY03CB, AK-47, Kalashnikov AK47, AR15, M4 Carbine, Acturus

Umarex NXG CO2 BB Pump Shotgun Field Test Review

No Comments

This review shows that low cost Airguns can perform just like higher priced Airguns. They may not be as realistic and all made out of metals for that added weight and feel but in terms of power and accuracy they can still get the job done as is with the Umarex NXG CO2 BB Pump Shotgun! In this Field Test Shooting Review I do just that, I test the power and accuracy first by shooting 5 rounds through my Chronograph to find out what the real world fps is, I then I shot 10 rounds down range at a fresh paper target to see what kind of grouping I can get and if the Umarex NXG CO2 BB Pump Shotgun is sighted in on the target out of the box.

Starting with the velocity test I first placed a brand new 12 gram CO2 into the Umarex NXG CO2 BB Pump Shotgun and loaded up the 10 rounds rotary magazine with Daisy Zinc Coated 4.5 mm Steel BB’s. The temperature was around 22 degrees Celsius which is 72 degrees Fahrenheit in the sea can indoor shooting range so not too warm or cold. The claimed fps from Umarex is 450, I was able to get an average of 403fps with the fastest shot hitting 425fps and the slowest shooting down to 388fps. So a bit under the Umarex claimed velocity but in the ball park.

Next I performed the accuracy test for the Umarex NXG CO2 BB Pump Shotgun and since the sights are non adjustable you kind of hope that where you aim is where the shots go but if they don’t then you will need to adjust your aim point just a bit. Out of the box the Umarex NXG CO2 BB Pump Shotgun did shoot a bit low but was fairly bang on side to side so when shooting at around 30 feet out you will need to aim just a tad over the intended target. Out of 10 shots, 8 rounds where all within a nice 1.5 inch grouping with a couple of flyers that I kind of want to keep out of this test because it was probably more me than the gun causing them to go off a bit. 1.5 inches is very good for a 4.5mm Steel BB Airgun!

All in all the Umarex NXG CO2 BB Pump Shotgun shot right around 400fps which is for sure a step up for something like a Red Ryder BB Rifle that at best can shoot 300fps. You also don’t have to work the pump as hard as you would the lever on a Red Ryder since the Umarex NXG CO2 BB Pump Shotgun is CO2 powered rather than spring powered. I also feel like the Umarex NXG Pump Shot was more accurate than the Red Ryder at least for me but that said some people can hit a nickel all day long with their Red Ryders! There are not a lot of Pump Action Looking Airguns out there in 4.5mm Steel BB versions and in more compact easier for younger or smaller shooters so if you fall into that category and want something in a shotgun format then the Umarex NXG CO2 BB Pump Shotgun may be perfect for you.

Categories: 6mm, BB, CO2, Field Test, Pump, Repeater, Review, Rifle, Vimeo Video Tags: Umarex, NXG Pump Shot

Umarex NXG CO2 BB Pump Shotgun Table Top Review

1 Comment

Type: BB Rifle.
Manufacturer: Umarex.
Model: NXG CO2 BB Pump Shotgun
Materials: Mostly all plastic construction.
Weight: 2 pounds (908 grams).
Length: 29.5 inches (749mm).
Barrel Length: 12 inches (30 cm) smoothbore barrel.
Propulsion: Single CO2 cartridge.
Action: Pump repeater.
Ammunition Type: 4.5mm steel BB's.
Ammunition Capacity: 10 rounds.
FPS: 450+ fps.

Trigger Pull: The trigger pull on the Umarex NXG CO2 BB Pump Shotgun is pretty decent, there is a short task up and fairly easy release as the pump action not only turns the rotary magazine but also cocks the internal hammer/striker system. So you will need to pump it before your first shot and after each shot.

Accuracy: I have not Field Test Reviewed the Umarex NXG CO2 BB Pump Shotgun yet but will be making a full Fields Test Review this week to find out what to expect in terms of accuracy and velocity. So we will find out if the fps is closer to the on the box specs of 450 fps or the mostly online specs of 490 fps. Perhaps somewhere in-between?

Build Quality: The Umarex NXG CO2 BB Pump Shotgun is almost all plastic which is not a bad thing in terms of quality and durability. The fact that it only weighs in at 2 pounds may make it feel kind of light and cheap but in a drop or fall situation it means it will most lily not sustain any damage because of the light weight. Most of todays airguns when made out of metals generally are made out of pot metal or zinc alloy which is a nice heavy metal that looks and feels great but is not super strong so when you drop a heavier gun made out of this material it can easily get damaged.

Realism: The Umarex NXG CO2 BB Pump Shotgun looks like a traditional pump action shotgun and even has a little bit of a recessed barrel to make it more believable but it is smaller in size since it is designed more for younger and smaller shooters. The light weight is not only a giveaway but makes ti feel more like a toy than a real gun. If you can ignore that then hopefully you can enjoy the Umarex NXG CO2 BB Pump Shotgun for what it is which is a low cost compact BB rifle made for customs interested in Airguns liek the Red Ryder but that perhaps want a bit more power.

Pros:

  • Low cost CO2 rifle great for all ages and sizes.

  • Has a fiber optic front sight.

  • Comes in a nice looking two tone Black/FDE color scheme.

  • Fairly easy to pump since the pumping action is not required to activate a spring or compress air.

  • Built in manual thumb safety.

  • Stock and high check rest position feel good and a good size length for smaller younger shooters.

  • Rotary drop out magazine holds 10 4.5mm steel BB’s for quick follow up shots.

  • Trigger feels pretty good, short and fairly light.

  • Full ambidextrous design.

  • Perhaps a step up for entry level shooter over a Red Ryder type BB rifle in terms of power.

  • Overall a decent looking air rifle.

Cons:

  • Mostly plastic, so a bit on the light weight side.

  • Sights are not adjustable in any way.

  • May be a bit cramped for larger shooters.

Comments: The Umarex NXG CO2 BB Pump Shotgun is not going to win any prizes for quality and realism but keep in mind it is really designed more for entry level younger shooters getting into the Airgun hobby. For them this will be not so intimidating as a larger, heavier more realistic version of a replica Shotgun. I think it will be realistic enough for most new Airgun Shooters and in terms of performance and features it is for sure a step up form something like a Red Ryder BB Rifle. I am looking forward to my upcoming Field Test Shooting Review out what the actual velocity is and what kind of groupings I can get shooting 30 feet down range on a paper target.

My Table Top Video of the Umarex NXG CO2 BB Pump Shotgun:

Categories: 4.5mm / .177 cal, BB, CO2, Field Test, Pump, Repeater, Review, Rifle, Vimeo Video Tags: Umarex, NGX, NXG Pump Shot