View fullsize

Type: Airsoft Rifle.
Manufacturer: Acturus.
Model: AR06 & NY03CB.
Materials: Mostly all Metal.
Weight: 5.6/4.9 pounds (2.5/2.2 kilograms).
Length: 27.4-30.7/31.7-35 inches (695-780/805-890mm)
Barrel Length: 11/14.6 inch (280/370mm) inner 6.02mm tight bore non rifled.
Propulsion: AEG (with Deans Connectors).
Action: Semi & Full Auto SAO.
Ammunition Type: 6mm Airsoft BB's.
Ammunition Capacity: Hi Cap/Mid Cap - 550/135
FPS: 380-400fps.

View fullsize

Trigger Pull: The trigger pull on the Arcturus AR06 - NY03CB AEG Airsoft Rifles like other AEG Rifles is not mechanical as they are essentially electrical driven so basically the trigger is an on/off switch that is closest in feel to a single action only trigger since it is light and short. You will notice a slight delay between pressing the trigger and the actual round being fired since the trigger activates a motor which first pulls the air spring back. Once the spring is fully drawn back it releases and compresses the air which then propelled the 6mm Airsoft BB. The higher voltage battery you use like an 11.1 volt will shorten the delay as the motor will spin faster and pull back the spring quicker allowing for less noticeable delay and also a higher rate of full auto fire which in this rifle is very noticeable.

View fullsize

Accuracy: I have not Field Test Reviewed either the Arcturus AR06 - NY03CB AEG Airsoft Rifles or even tried them out yet. I hope to get to my Field Test Shooting Video for both of them later next week, until then we can assume they will shoot similar to most other AEG rifles with tighter bore barrels. I am expecting at least a 2 inch grouping at 30 feet down range in semi auto. In terms of velocity the test paper which they come with claims around 390+fps.

View fullsize

Build Quality: The Arcturus AR06 is a mostly metal with a full metal receiver while the NY03CB has a polymer or plastic receiver which from what I can tell only other components being plastic would be the pistol grips and rear stock. other metal parts on both AR type Airsoft Rifles would be the rail setup, the barrel, the charging handle, the buffer tube, the dust cover, the trigger, the selector switch, the magazine release and bolt release. Fit and finish for both guns is very good.

View fullsize

Realism: The Arcturus AR06 - NY03CB AEG Airsoft Rifles are based on the AR platform with both versions looking the part of a real steel AR. They do come with the removable orange tips installed but they also come with black flash hiders so you can easily switch them out adding to the realism. The metal receiver on the AR06 does give it a bit more weight but even the NY03CB has a decent weight and solid feel to it. Most of the controls work just like a real steel AR including the charging handle, bolt release, selector switch and magazine release.

View fullsize

Pros:

• Two versions to meat your budget, both great options.

• Quality components throughout both versions. Only real difference is nylon fiber receiver vs metal receiver and slight upgrade motor on AR06 version from Long Type to Long Type 19k torque motor on AR06.

• Have been quality control inspected including 5 round recorded fps test with .20 gram Airsoft BB’s.

• Both  have a functioning bolt catch.

• Both come with Quick release two position fully adjustable pop-up sights.

• Both come with additional black flash hiders.

• Lots of rial mounting options in Picatinny and M-LOK.

• 6 position adjustable rear stocks.

• Easy access to motor for any possible trouble shooting you may need to do.

• Additional grip plate option.

• Ambidextrous controls and ambidextrous sling mounting points (QD on AR06).

• Two magazines come with AR06 (Mid Cap and High Cap).

View fullsize

Cons:

• Limited battery options as area is small.

• Kind of need a tool to remove rear stock for battery access. (Could change the rear stock)

• Mystery accessory baffles me and not mentioned in the manual.

View fullsize

Comments:

Like the AK series of Acturus AEG Airpot Rifles, the Arcturus AR06 - NY03CB AEG are good value for the money with the AR06 offering a slightly higher premium over the lower cost NY03CB. But don’t let the lower price fool you into thinking you are getting a sub-standard product as both versions are built with many of the same components. I personally like the more compact look of the Arcturus AR06 AEG Airsoft Rifle but then again the price of the NY03CB AEG Airsoft Rifle is hard to ignore. Either way you can’t go too wrong so make your pick and enjoy owning one of them.

My Table Top Video of the Acturus AR06 - NY03CB AR AEG Airsoft Rifles:

• Buy the Acturus AEG Airsoft Rifles in Canada

• Buy the Acturus AEG Airsoft Rifles in the US

In this Preview Unboxing Video I Take a look at 4 new Airsoft products from Arcturus all of them being AEG Airsoft Rifles with two based on the AK platform and the other two based on the AR platform. Three of the AEG Airsoft Rifles are mostly metal while I also feature a lower cost version with a Nylon Fiber Polymer receiver. All of these Replica AEG Airsoft Rifles are very good quality but you will get all metal (mostly steel and aluminum) build and a Hi-Cap and Mid-Cap magazine with the higher cost versions.

View fullsize

Arcturus AK05 AK AEG Airsoft Rifle:

• Type: Airsoft AEG.

• Manufacturer: Arcturus.

• Caliber: 6mm plastic Airsoft BB's.

• FPS Range: 380-400.

• Magazine Capacity: 550rd Hi-Capacity and 30/135rd Mid-Capacity.

• Thread Direction: 14mm Negative.

• Gearbox: Version 3 Full Metal w/ Quick Change Spring, Fully Upgradeable.

• Motor: Short Type.

• Fire Modes: Semi/Full-Auto, Safety.

• Battery: 9.6v Small Stick Type or 7.4v stick LiPo recommended.

• Battery Location: Wired to dust cover with small Tamiya connector.

• Hopup: Yes, Adjustable.

• Inner Barrel: 280mm / 6.02mm.

• Length: 790mm - 875mm, Adjustable.

• Weight: 3730g.

• Package Includes: Gun, Hi-Cap Magazine, Mid-Cap Magazine.

View fullsize

Arcturus AK06 AK AEG Airsoft Rifle:

• Type: Airsoft AEG.

• Manufacturer: Arcturus.

• Caliber: 6mm plastic Airsoft BB's

• FPS Range: 380-400.

• Magazine Capacity: 550rd Hi-Capacity and 30,135rd Mid-Capacity.

• Thread Direction: 14mm Negative.

• Gearbox: Version 3 Full Metal w/ Quick Change Spring, Fully Upgradeable.

• Motor: Short Type.

• Fire Modes: Semi/Full-Auto, Safety.

• Battery: 9.6v Small Stick Type or 7.4v stick LiPo recommended.

• Battery Location: Wired to dust cover with small Tamiya connector.

• Hopup: Yes, Adjustable.

• Inner Barrel: 250mm / 6.02mm.

• Length: 480mm, 695mm (Folded, Unfolded).

• Weight: 2730g.

• Package Includes: Gun, Hi-Cap Magazine, Mid-Cap Magazine.

View fullsize

Arcturus AR06 AR AEG Airsoft Rifle:

• Type: Airsoft AEG.

• Manufacturer: Arcturus.

• Caliber: 6mm plastic Airsoft BB's

• FPS Range: 380-400.

• Magazine Capacity: 320rd Hi-Capacity and 130rd Mid-Capacity.

• Thread Direction: 14mm Negative.

• Gearbox: Version 2 w/ Quick Change Spring, Fully Upgradeable.

• Motor: Long Type, 19k torque motor.

• Fire Modes: Semi/Full-Auto, Safety.

• Battery: 7.4v stick LiPo recommended.

• Battery Location: Wired to buffer tube with small Tamiya connector.

• Hopup: Yes, Adjustable.

• Inner Barrel: 280mm / 6.02mm.

• Length: 695mm - 780mm, Adjustable.

• Weight: 2520g.

• Package Includes: Gun, Hi-Cap Magazine, Mid-Cap Magazine.

View fullsize

Arcturus NY03CB AR AEG Airsoft Rifle:

• Type: Airsoft AEG.

• Manufacturer: Arcturus.

• Caliber: 6mm plastic Airsoft BB's

• FPS Range: 380-400.

• Magazine Capacity: 330rd Hi-Capacity.

• Thread Direction: 14mm Negative.

• Gearbox: Version 2 Gearbox w/ Quick change spring system, Fully upgradeable.

• Motor: Long Type.

• Fire Modes: Semi/Full-Auto, Safety.

• Battery: 7.4v stick LiPo recommended.

• Battery Location: Wired to buffer tube w/ Deans Connector.

• Hopup: Yes, Adjustable.

• Inner Barrel: 370mm~ / 6.02mm.

• Length: 805mm - 890mm, Adjustable.

• Weight: 2020g.

• Package Includes: Gun, Hi-Cap Magazine.

View fullsize

Type: Airsoft Pistol.
Manufacturer: KWC.
Model: DE L6 Desert Eagle.
Materials: Metal & plastic.
Weight: 2.5 pounds (1100 grams).
Barrel Length: 5.1 inches (Smooth bore).
Total Length: 10.75 inches.
Propulsion: CO2.
Action: Blowback semi & full auto, single action only.
Ammunition Type: 6mm plastic Airsoft BB's.
Ammunition Capacity: 21 rounds.
FPS: 360fps claimed.

View fullsize

Trigger Pull: The trigger pull on the KWC DE L6 Desert Eagle CO2 Blowback Full Auto Airsoft Pistol is single action only which means you will need to rack the slide to not only draw the hammer back but to also chamber the first round. After that the blowback action will do this for you until you are out of ammo and then the slide will lock back. You can also manually draw the hammer back if a round is already chambered. The trigger itself is really nice, it’s light, super short with a crisp light release perfect for fast action shooting.

View fullsize

Accuracy: At this point I have not made my Field Test Shooting portion of my review for the KWC DE L6 Desert Eagle CO2 Blowback Full Auto Airsoft Pistol so I really don’t know what to expect? KWC claims an fps of 360 using CO2 as its power source and it is a realistic velocity based on previous Velocity tests with similar KWC Airsoft Guns. In terms of accuracy, again I have no idea since I have not reviewed this version of Desert Eagle before. So stay posted till next week when I make the Field Test Shooting Review for it.

Build Quality: Overall the metal and plastic build quality of the KWC DE L6 Desert Eagle CO2 Blowback Full Auto Airsoft Pistol is good. It is mostly metal with a plastic frame, the real steel version would have an aluminum frame and has a weight closer to 4 pounds total so a bit lighter in terms of weight compared to the powder burning version. The fit and finishes look good.

View fullsize

Realism: The KWC DE L6 Desert Eagle CO2 Blowback Full Auto Airsoft Pistol is an excellent Replica Airsoft version of the real steel L6 Desert Eagle including the top and bottom rails and the ported front barrel. It also has full blowback action and you can fully field strip it. I like the addition of the fingered grips which I think adds ot the overall looks and function of this Airsoft Pistol.

Pros:

• Lots of metal and good overall weight to it.

• Very accurate replica of Desert Eagle L6.

• Ergonomic rubberized grips.

• Semi and full auto selectable.

• Adjustable hop-up.

• No orange tip.

• CO2 for more power over GBB.

• Uses standard KWC CO2 Desert Eagle magazines.

• Picatinny rail top and bottom for lots of accessory mounting options.

• Great light weight single action only trigger with super short take-up.

View fullsize

Cons:

• Frame is plastic so compared to real steel version is much lighter.

• Non adjustable sights, also all black so may be hard to see on darker targets.

• No trademarks since non-licensed version via KWC direct.

• Very large gun with large grips so not suitable for smaller handed shooters.

View fullsize

Comments:
Going off just the looks and feel for the KWC DE L6 Desert Eagle CO2 Blowback Full Auto Airsoft Pistol I can say for sure I do like it compared ot the standard KWC Desert Eagle with its venting up front and its ergonomic rubberized grips. I hope when I perform the Field Test Shooting Video fo fit it it performs well as the price point is good at around $200 Canadian and who doesn't want to have a Desert Eagle in their Replica Airgun collection at the end of the day!

My Table Top Video of the KWC DE L6 Desert Eagle CO2 Blowback Full Auto Airsoft Pistol:

• Buy the KWC DE L6 Desert Eagle CO2 Blowback Full Auto Airsoft Pistol in Canada

• Buy similar Desert Eagles Airsoft Pistol in the US

This video is primarily for my viewers over on the Replica Airguns channels as I have not posted anything about what's been going on with me the last month and a bit. My Airgun channel does not have very much personal content like my GetFitOver40 channel does, so I wanted to fill them in on where I have been and what's been going on.

In this video I talk about being in the hospital for a month because I was experiencing shortness of breath and a feeling of pressure in my diaphragm area which was later found out to be a heart problem.

Unknown to me I had been born with a Congenital Heart Defect where my Aortic Valve was defective which over time had cause the Aortic Root area to double in size (3cm normal to 6cm).

This defect caused my heart to work a lot harder then normal making it enlarge over time which is not good and reduces it's pumping ability. Before my operation my heart function was below 20%, a normal healthy heart is around 60%.

While in the hospital I had open heart surgery on my Aortic valve replacing it along with a section above it. I also had a Pacemaker/Defibrillator put in. There where a lot of concerns because my heart was also enlarged and not functioning that well, the doctor even said they may not be able to get me off of bypass which would then require an emergency heart transplant. The good news is the operation went well and no need for a new heart at least for now...

I was in the hospital for longer than normal because of my enlarged heart and because of all the stress to it. I was in and out of what's called Atrial Fibrillation. This is when the heart beats very irregularly and faster than normal. It can be short term or longer term and can sort itself out or require intervention to help get back to a Sinus Rhythm. At the time of this post I believe it has gone back to the normal Sinus Rhythm, so fingers crossed it stays this way.

As you can imagine, this has been a life changing event and means my lifestyle will be changing a bit. I will not be doing anything to overstress my heart but that does not mean no more fitness for me, just a different fitness approach. Perhaps a more scaled back approach but I am always up for a challenge and this is no different in terms of how I would approach any challenge in my life.

So if you are a Replica Airguns follower and want to follow my "Road to Recovery" you can do that over on my GetFitOver40 channels. Other than that I will be making regular Airgun Videos moving forward now that I am at home.

View fullsize

Type: Pellet Air Pistol.
Distributer: KWC.
Model: KWC 24/7 TAC NBB Pellet.
Materials: Metal and polymer build.
Weight: 1.76 pounds (799 grams).
Barrel: Rifled steel.
Propulsion: CO2 x1.
Action: Semi auto non-blowback, double action only.
Ammunition Type: .177 caliber pellets.
Ammunition Capacity: 16 rounds (2x8).
FPS: 360-370.

Trigger Pull: The trigger pull on the KWC 24/7 TAC Non-Blowback CO2 Pellet Pistol is a bit on the medium to heavy side so it’s not going to make for the best action shooter as it is a double action only shooter when compared to a single action only trigger or a single and double action trigger. As with most double action triggers it is a bit longer and slightly heavy but not unusable, just be prepared to get a little bit of a finger workout.

View fullsize

Accuracy: I have not shot the KWC 24/7 TAC Non-Blowback CO2 Pellet Pistol just yet but will be doing so probably next week so stay posted for my Full Field Test Shooting Video for the KWC 24/7 TAC Non-Blowback CO2 Pellet Pistol. I expect it to perform well in terms of accuracy and power since there is no blowback operation to have to compensate for. Having a rifled barrel should also help with accuracy! We will see shortly.

Build Quality: The KWC 24/7 TAC Non-Blowback CO2 Pellet Pistol is built as expected just like all the other KWC Airguns. KWC has been making Airguns for a while not just for themselves but for other companies like Umarex, Gletcher, ASG, Crosman and even Sig Sauer and so quality control and durability have to stand up to these manufacturers standards. You will find metal on this gun where it matter. The slide, the full size drop out metal magazine and of course lots of internal parts. The frame, magazine release, trigger and safety are all plastic. I do like the feel of the rubberized grips for sure! Fit and finish is good overall and the fact that this is a fairly simple Airgun design with no blowback action or even a moving slide, so less moving parts means there is less chance for something to go wrong so it should last a while even with a fair amount of use.

View fullsize

Realism: The KWC 24/7 TAC Non-Blowback CO2 Pellet Pistol shares it’s looks with the Taurus 24/7 but is not an exact replica. The trigger guard is a bit different and so is the placement of the controls and even the slide and frame are not exact but very similar. In terms of size, weight and vernal overall design for sure the KWC 24/7 TAC Non-Blowback CO2 Pellet Pistol looks a lot like a Real Steel Taurus 24/7 at first glance.

Available at the: Replica Airguns Store

Pros:

• Good weight and solid feeling gun. Lots of metal where you need it in the slide, magazine and other internals.

• All metal full size drop out magazine holds CO2 and 16 pellets.

• Decent looking replica (but not bang on) of a Taurus 24/7.

• Not a lot of writing on the gun, very clean looking (Non Ranger version).

• Recessed barrel helps with look of realism.

• Fiber Optic front and back sights for easy sight acquisition.

• Rifled barrel will help with accuracy.

• Non-blowback operation with increased fps and CO2 efficiency.

• Rail on top of slide and frame for lots of accessory add on options.

• Double action trigger is long but not overly heavy so should be OK for action shooting.

View fullsize

Cons:

• No blowback, slide is fixed and does not move but can be removed with a tool for internal access and cleaning.

• No single action shooting so may not be the most accurate for slowed down shooting.

• Sights are not adjustable but you can add an adjustable red dot to it using the rail setup.

• Hard to tell when out of ammo, have to listen to the sound or count shots.

Comments:

It is nice to see more full size drop out metal magazine Replica Pellet Pistols coming out in the Airgun market just liek the KWC Makarov PM I just reviewed. Generally speaking most are going to be non-blowback but there are a few blowback options. That said a Non-blowback CO2 Pellet Pistol like the KWC 24/7 TAC Non-Blowback CO2 Pellet Pistol will typically give you a high velocity and more shots per CO2 and can even be a little bit better in the accuracy department since there is virtually no recoil from them. The KWC 24/7 TAC Non-Blowback CO2 Pellet Pistol is a nice little Taurus 24/7 looking Airgun that has a nice modern look and feel to it. Hopefully it performs well for me during my Field Test Shooting Video I will be making soon for it.

My Vimeo Videos for the KWC 24/7 TAC Non-Blowback CO2 Pellet Pistol:

• Buy the KWC 24/7 NBB CO2 Pellet Pistol in Canada

• Buy Pellet Pistols in the US

Save big this long weekend with our Early Black Friday Sale! Grab some new guns, and tactical gear all for cheap. Everything here has prices slashed up to 50% off.

View fullsize

Type: Pellet Pistol.
Distributer: Umarex.
Model: Stainless Ruger Mark IV.
Materials: Metal and polymer build.
Weight: 1.56 pounds (708 grams).
Barrel: 5.3 inches (135mm).
Total Length: 11 inches (279mm).
Propulsion: Spring Piston.
Action: SAO Break Barrel.
Ammunition Type: .177 caliber pellets.
Ammunition Capacity: 1 round.
FPS: 320.

View fullsize

Trigger Pull: The trigger pull on the Stainless Ruger Mark IV Break Barrel .177 Cal Pellet Pistol is not too bad, I feel it is a around 6-7 pounds or so without measuring. In comparison to a real steel 22LR semi auto SAO trigger pistol, the trigger is much heavier but most of these 22LR pistols of this nature have what I would consider to be near perfect triggers. Over time once you get use to the pressure and release point accuracy with this pistol it is for sure possible.

View fullsize

Accuracy: I have tested out the all black version of this pistol which will perform exactly the same or should I say is expected to perform the same since they are virtually the exact same Pellet Pistol but in different finishes. You can watch my Field Test Shooting Video for the all black version but in case you don’t make it there I will fill you in on the basic results… In terms of velocity I averaged 312 fps using 7 grain lead pellets and got around a 2 inch 7 rounds grouping but expect with a bit more trigger time to get closer to 1 inch.

View fullsize

Build Quality: The Stainless Ruger Mark IV Break Barrel .177 Cal Pellet Pistol is a low cost target plinker that also doubles as a licensed Replica for that coolness factor so you won’t get an all metal super top quality build here. That said metal and plastics are well used and for sure details in the fit and finish have been improved over the Buck Mark URX version where I found the barrel felt a bit sloppy and the trigger was plastic. The Umarex Ruger Mark IV Break Barrel .177 Cal Pellet Pistol has a much tighter barrel fit when closed and the trigger is now metal! Maybe Umarex watched my video back in the day and took some notes?

View fullsize

Realism: The Umarex Ruger Mark IV Break Barrel .177 Cal Pellet Pistol most resembles the Mark IV Hunter edition and is pretty much bang on in terms of being a replica other than the tell tail hinge just under the barrel required for a spring piston design, there really is no way to get around this so I’m not going to criticize this minor difference. The real steel version is almost 3 pounds and so the pellet shooting version is a bit under weight so it would have been to have had more metal perhaps in the barrel and lower frame. Again since the pellet shooting version is a springer you will not have any working bolts or slide catches or a built in magazine.

View fullsize

Pros:

• It's a decent Ruger Mark IV Replica!

• Feels well built overall.

• Expect it to have really good accuracy like the Umarex Browning Buck Mark URX since they share similar mechanical design.

• Barrel locks into place much better than the Umarex Browning Buck Mark URX did.

• Fully adjustable rear sight with fiber optic front sight.

• Auto locking safety, just don’t forget to unlock before each shot

• Actual metal trigger in this version.

• Nice and compact, not too heavy.

• Full Ruger licensed via Umarex.

• Fairly low price tag.

View fullsize

Cons:

• No built in rail for a sight system like the Umarex Browning Buck Mark URX.

• Would have liked a metal trigger and maybe a slightly lighter trigger pull to match the real Buck Mark's very light trigger pull.

• A bit more metal would have been nice.

• Significantly more expensive than the black version which is the same exact gun in a different color.

View fullsize

Comments:
The Stainless Ruger Mark IV Break Barrel .177 Cal Pellet Pistol is a decent looking replica and a decent pellet shooting target pistol and if you own the real steel version in 22LR you may just want to get your hands on one of these Break Barrel Replica Pellet shooters. The only real question is do you get the Stainless version with simulated wood grips or the all black version? If you like the look of the stainless version and don’t care about money whatsoever, then pickup that one up since it is a Limited Edition version that will only go up in value over time. If you are on a budget and don’t mind the look of the all black versions or maybe even prefer it then by all means grab one since at the end of the day they will both perform exactly the same.

My Vimeo Table Top Review Videos for the Umarex Stainless Ruger Mark IV Break Barrel .177 Cal Pellet Pistol:

• Buy the Umarex Stainless Ruger Mark IV Break Barrel .177 Cal Pellet Pistol in Canada

• Buy the Umarex Stainless Ruger Mark IV Break Barrel .177 Cal Pellet Pistol in the US

View fullsize

Type: Airsoft pistol.
Distributer: Umarex.
Model: Smith & Wesson M&P 9L.
Materials: Metal and polymer build.
Weight: 1.7 pounds (757 grams).
Barrel: 4.75 inches (121mm), non-rifled.
Total Length: 8.5 inches (215mm).
Propulsion: CO2 x1.
Action: Semi auto blowback, single action only
Ammunition Type: 6mm plastic Airsoft BB's.
Ammunition Capacity: 15 rounds.
FPS: 410 Claimed.

View fullsize

Trigger Pull: The trigger pull on the Umarex S&W M&P 9L Blowback CO2 Airsoft Pistol is fairly light weight being a single action only trigger. There is about a quarter inch of take up with an easy release that is not hitchy at all. You will need to rack the slide to load your first Airsoft BB into the breach and engage the action but on the first shot but then the blowback action does this for you until the Airsoft Pistol is out of ammo and the slide locks back.

View fullsize

Accuracy: I have not performed my Field Test Shooting Video for the Umarex S&W M&P 9L Blowback CO2 Airsoft Pistol so stay posted for that video coming out in the next couple of weeks. Umarex has claimed a velocity of around 410 FPS using .20 gram Airsoft BB’s but that does seem a bit quick, well will have to see when I place some shots though my Chronograph! In terms of accuracy I expect it to shoot about the same as most Full Blowback Airsoft Pistols which generally produces a 1.5 to 2 inch 10 shot grouping from 30 feet out using a semi rested shooting position. Again we will find out when I perform my Field Test Shooting Video for the Umarex S&W M&P 9L Blowback CO2 Airsoft Pistol.

View fullsize

Build Quality: The Umarex S&W M&P 9L Blowback CO2 Airsoft Pistol build quality is fairly decent, fit and finish looks good with not too much slide wiggle and the materials used are both metal and plastic or polymer that look to be good quality. I do expect some of the black finishes ot come off on the high spots as these guns are generally electroplated and not too thick with it but this can actually make the gun look more realistic with that slightly worn in look to it.

View fullsize

Realism: The Umarex S&W M&P 9L Blowback CO2 Airsoft Pistol in terms of looking like the real steel version of its counterpart is very close for sure, it would be hard to tell without really taking a close look t it. Everything about this Replica Pistol works for the most part like the real steel version including most of the mechanical parts like the slide catch release, magazine release, take down lever, trigger safety and you can even fully field strip it which gives you easy access to the hopup on the barrel. Of course the full blowback action really seals the deal in terms of making this gun shoot like a real semi auto pistol.

View fullsize

Pros:

• Very accurate replica of the S&W M&P 9L.

• Fairly accurate weight and feel to it.

• Metal and plastic parts where you find them on the real steel version, fit and finish is good.

• Working trigger safety and ambidextrous working slide catch release.

• Full size dropout metal magazine that holds Airsoft BB's and CO2.

• Warning instructions are discreet under the trigger guard.

• Recessed barrel and hidden CO2 screw for more realistic look

• Fully Smith & Wesson licensed via Umarex.

• Rail for add on accessories.

• White dot sights for easy target acquisition.

• Comes with three sizes of interchangeable grips S/M/L.

• Adjustable hopup so you can at least adjust elevation at range.

• Comes in a box rather than a clamshell.

View fullsize

Cons:

• Has an orange tip but could be painted black or silver to match.

• Sight are not adjustable.

• 15 round magazine has less capacity than some other blowback Airsoft Pistols.

View fullsize

Comments:
The Umarex S&W M&P 9L Blowback CO2 Airsoft Pistol is a nice addition to the Smith & Wesson M&P line of Replica Airguns. I’m glad they made it in full blowback but being Airsoft based that is generally the way they lean towards. Hopefully we get to see 4.5mm Steel BB version too in the future! For now we have it in Airsoft and with the longer barrel perhaps it will shoot a bit hotter than most of the other CO2 Blowback Airsoft Pistols, maybe even 410fps like Umarex claims but I will be surprised if it does. I will be happy to see something in the high 300’s to be honest. No matter what, you now have yet another Smith & Wesson option to consider when looking for your ultimate Replica Airgun!

My Vimeo Videos for the Umarex S&W M&P 9L Blowback CO2 Airsoft Pistol

• Buy the Umarex S&W M&P 9L Blowback CO2 Airsoft Pistol in Canada

• Buy Airsoft Pistols in the US

View fullsize

Type: Pellet Rifle.
Manufacturer: Umarex
Model: HK MP7 .177.
Materials: Metal and Polymer.
Weight: 4.4 pounds (2kg).
Barrel: 11.7 inches (29.7cm).
Total Length: 31 inches (78.7cm).
Propulsion: Break Barrel Spring Piston.
Action: Single Action Single Shot.
Ammunition Type: .177 Caliber Pellets.
Ammunition Capacity: 1.
Max FPS: 490 Claimed.

View fullsize

Trigger Pull: The trigger on the Umarex HK MP7 .177 Cal Break Barrel Pellet Gun is single action only requiring you to break the barrel and compress the internal spring piston before you can shoot it. The actual trigger pull is pretty decent overall. There is very little take-up but the creep is on the longer side but fairly smooth requiring medium pressure. The release is a bit hard at first to predict but nothing some trigger time can’t get you use to.

View fullsize

Accuracy: I have not performed any shooting tests with the Umarex HK MP7 .177 Cal Break Barrel Pellet Gun so far. I hope to make that Video Review next week. I expect the Umarex HK MP7 .177 Cal Break Barrel Pellet Gun to perform well in the accuracy department especially with the included Red Dot Optical Scope installed. I hope the velocity rating from Umarex is based on lead pellets and not hyper velocity light weight pellets but we will find out the story when I perform my Field Test Shooting Video shortly!

View fullsize

Build Quality: The Umarex HK MP7 .177 Cal Break Barrel Pellet Gun is a China made Airgun but looks to be well made. It has lots of metal parts as you would expect from a Spring Piston Rifle which adds a nice weight and feel to it. I did however have an issue with the front plastic mock Suppressor/Compensator as it does not seem to be attached to the metal barrel very well other than being pressure fit which is not going to cut it with all the vibration a spring piston system makes. My first shot loosened the mock Suppressor/Compensator so I will either have to hold it when shooting or find another way to make sure it stays in place.

View fullsize

Realism: The Umarex HK MP7 .177 Cal Break Barrel Pellet Gun is kind of unique in this department as most break barrel rifles are not Replicas, especially the more compact sub machine gun styled ones. Umarex did good job making the Umarex HK MP7 .177 Cal Break Barrel Pellet Gun look like a real HK MP7 for the most part. Of course it is a Spring Piston Rifle at its core so exceptions had to be made to make this work including molded non working parts like the magazine release, sector switch and, bolt/ejection port. That said all in all it is a decent looking replica considering it is a Break Barrel Airgun under the skin.

View fullsize

Pros:

• Not many Replica Pellet Rifles on the market, especially in a more compact gun.

• Comes with Red Dot sight.

• Lots of rails for adding accessories to it.

• Full HK Licensed by Umarex.

• Collapsible Wire Stock.

• Nice high claimed 490 fps.

• No need for CO2 so low cost to cooperate.

• Not effected by temperature like a CO2 Airgun.

• Should have better accuracy than most BB Replica Airguns.

• Very solid feel to it, good overall weight and feel.

View fullsize

Cons:

• Not going to be an action shooter, have to reload after each shot.

• A good overall Replica but not as Realistic or full operation as a BB version would be.

• Mock Suppressor/Compensator poorly attached to barrel.

View fullsize

Comments:
The Umarex HK MP7 .177 Cal Break Barrel Pellet Gun is an interesting product, on one hadn't it is a Replica Airgun and most people expect a Replica Airgun to have all of the appropriate working parts similar to what would be found on the real steel version. But since this is a Break Barrel Airgun at the core the Umarex HK MP7 .177 Cal Break Barrel Pellet Gun will not function the same as the Real Steel version so as long as you don’t expect it to and appreciate the fact that it should be a nice accurate low cost to operate target rifle then I think you will understand this product and enjoy it for what it is… A Single Shot Pellet Rifle that looks a lot like a HK MP7.

• Buy the Umarex HK MP7 .177 Cal Break Barrel Pellet Gun in Canada

• Buy the Umarex HK MP7 .177 Cal Break Barrel Pellet Gun in the US

View fullsize

Type: BB Rifle.
Manufacturer: Crosman.
Model: ST-1.
Materials: Metal & plastic.
Weight: 6.07 pounds (2.75 kilograms).
Total Length: 17.75/33 inches (Pistol/Rifle).
Barrel Length: 15.5 inches.
Propulsion: 12 gram CO2 dual cartridges.
Action: Blowback - single action only.
Ammunition Type: 4.5mm steel BB's.
Ammunition Capacity: 25 Round/Spring - 300 Round/Hopper.
FPS: 480fps.
Rate of Fire: 1400 rounds per minute in full auto

View fullsize

Trigger Pull: The trigger pull on the Crosman ST-1 CO2 Blowback Full Auto Steel BB Machine Gun is single action only since the right side charging handle must be cocked first before you can shoot it to engage the action. The trigger is short and fairly light but not overly light. The real fun happens with the Crosman ST-1 CO2 Blowback Full Auto Steel BB Machine Gun when you switch it over to full auto mode and with just one pull and hold of the trigger you empty the 25 round magazine in a mere matter of seconds at 1400 rounds per minute.

View fullsize

Accuracy: I have not actually shot this BB Rifle to date but expect it to get similar results to the other Crosman Full Auto BB Machine guns I have already reviewed. I am expecting a bit more velocity with the longer barrel extension installed and would be happy if I was able to get in the mid 400’s. Accuracy should also be about the same with 1 inch semi auto groups from 30 feet out expending a bit when in full auto.

View fullsize

Build Quality: The Crosman ST-1 CO2 Blowback Full Auto Steel BB Machine Gun is well made all around. Weighing in at 6.07 pounds without any add on accessories other than the included compact Red Dot sight. It feels solid and well built. There is a lot of metal going on inside and out of this rifle but keep in mind the top and bottom receiver are plastic with metal parts where they need to be like in the internals, pretty much all the working parts are metal, the magazine is full metal, the buffer tub is metal, charging handle, selector switch, magazine release, bolt release, trigger and of course the barrel is metal.

View fullsize

Realism: The Crosman ST-1 CO2 Blowback Full Auto Steel BB Machine Gun is not modeled after any real steel gun I know of. It resembles a futuristic weapon you would see in a SciFi Action Movie or Alien First Person Shooter. I was not a fan of it when it was first released by Crosman but after seeing and holding it in person it is growing on me quickly.

View fullsize

Pros:

• Very unique, not like your regular Replica Rifles, very futuristic in design.

• Drop out magazine doubles as the 300 round hopper and holds CO2 and BB’s.

• Comes with Red Dot Sight and lots of rails for mounting what every you want on it.

• Can be either a Pistol or Rifle or a PDW by adding or removing the Barrel Extension and Rear Stock.

• Barrel Extension actual lengthens the barrel and should increase fps, not just for show!

• Tactile comfortable rubber padding in multiple locations.

• Semi auto and full Auto selectable.

• Expected higher fps of up to 480.

View fullsize

Cons:

• Some people may not like the look? Not like your normal modern rifle.

• Front rubber grip comes off really easy at least on mine?

• Will require barrel extension for full velocity.

View fullsize

Comments:

The Crosman ST-1 CO2 Blowback Full Auto Steel BB Machine Gun is a brave move by Crosman, I was not expecting something like this from them and when I originally saw it I was not sure if it was a good idea or not but again once seeing it in person and actually holing it I feel a lot better about it. It will for sure appeal to those looking for a futuristic Airgun or wanting something that looks like a gun from a video game or SciFi movie. I also like the versatility you have with the Crosman ST-1 CO2 Blowback Full Auto Steel BB Machine Gun being able to configure it how you like either as a Pistol, full on Rifle or PDW style shooter.

My Table Top Video of the Crosman ST-1 CO2 Blowback Full Auto Steel BB Machine Gun:

• Buy the Crosman ST-1 in Canada

• Buy the Crosman ST-1 AR in the US

As the title suggest this a video about a Huge Mystery Box so I am not going to say what’s in it, I can say that their are 4 main products mostly rifles per-say. One is a Futuristic Full Auto BB Rifle, one is a Paintball Shotgun, One is an AEG Airsoft Rifle and one is a Replica Break Barrel Pellet Rifle.

So I have a lot of variety here to show everyone! I did absolutely zero research on any of the products I show in this video since like you I had no real idea what was inside other than how many and that most where rifle based.

Enjoy finding out what new products I will be reviewing over the next month with dedicated Table Top and Field Test Shooting videos.

I have been making a bunch of instructional videos lately mainly because i have not had a lot of new products to share with everyone, I am expecting 4 new Airguns that where supposed to arrive on Monday but Canada Post has for some reason delayed their arrival and so I am not sure when I will see them? Hopefully very soon!

As soon as they arrive I will make a Preview Video to show off all 4 products, sorry I can not tell you what they are as I don’t know, it’s a surprise for all of us which can be fun opening up a mystery box :) I will also be making dedicated Table Top and Field Test Shooting Videos for all 4 guns which should keep me busy for the next month or so…

On another note I am around 5 weeks out to my latest Fitness Show the Vancouver Fall Classic where I will be competing in Mens Physique and possibly Men’s Classic Physique. This event is taking place local to me in New Westminster BC Canada on November the 12th if anyone is local and wants to check it out!

I mention this because over the next 5 weeks I begin to do the most challenging part of my contest prep which requires a very strict low calorie diet along with a ton of activity (generally weight training 6 day per week with at least 5-6 miles of walking each day). This puts me in a good caloric deficit which enables me to lose around 2 pounds of fat per week which I am hoping will get me to around 5% body fat by show day this time around.

This is not a healthy body fat to be in for any length of time but is what I need to do to be competitive and show off the muscle on stage I have added during my contest prep. Less fat means more muscle detail which makes the muscle look bigger on stage.

This does all come at a cost of me feeling rather like garbage much of the time as my body is thinking I am starving and as expected will try and deter me from this course of action by making me extra hungry and very tired. Also keeping me awake much of the night so I can go out and find food LOL.

So if you notice me looking a little off this is why, I will do my best to still be entertaining and pleasant during my videos but I do get a bit irritated and I often lose my train of thought. You can checkout my Fitness stuff over on my fitness page www.GetFitOver40.com if this type of thing interests you.

Different Types of Airgun Sights

View fullsize

Sights for guns in general are the same for Airguns as is with real steel guns for the most part and can be mixed and matched with a couple of exceptions. Spring piston rifles for instance are an exception because of the unique vibration the spring makes and how it can damage a standard optical sight, so in this case you’re best to use an optical sight designed for a spring piston Airgun. In most other cases sights can be used on all types of guns.

In this Airgun Sights video I will go over the various types of sights that either come as part of the gun design or can be added afterwards using a rail or mounting system.

Types of Airgun Sights most commonly used.

View fullsize

Iron Sight (Fixed or removable).

Iron Sight (Adjustable).

Iron Sight (White Dot, Fiber Optic).

Come in Post/Notch, Post/Aperture (Peep).

Common on Pistols and Rifles

View fullsize

Laser Sight:

Generally added to a rail or can sometime be integrated into the design of the gun.

Common on both Pistols and Rifles.

View fullsize

Red Dot and Holographic:

Generally not magnified.

Most common on Rifles but can be used on Pistols.

View fullsize

Optical Magnified (Telescopic)

Come in a variety of magnifications for different shooting ranges.

Generally for Rifles but can be used on Pistols.

View fullsize

Gun Safeties generally are going to be similar for all types of guns, so Safeties used with Airguns are often the same types as used with Real Steel Guns. Some guns will have no Safeties at all while other guns many have multiple Safeties on them. In this informative video I go over six of the more common types of Gun Safeties used in Real Steel Guns and Air Guns.

View fullsize

Here is a list of the more common types of gun Safeties.

• Trigger Safety

• Cross Bolt Safety

• Slide Safety

• Frame Safety

• Grip Safety

• Magazine Safety

View fullsize

I sometimes mention in my review videos that a gun is either Full Blowback or Partial Blowback and some people may not understand exactly what this means and how it effects the Airguns Blowback Action and Performance so I figured it would be best to make a dedicated video talking about the differences and also some of the Pro’s and Con’s of each type of Blowback Action.

In the video I obviously go into a fair amount of detail and show you around each type of Airgun and Magazine as they do differ a fair amount but to summaries for you here in this written form, the main difference is going to be how much the slide moves back and forth. With Full Blowback Airguns the slide will move much longer back and forth on the frame of the Airgun much like a real gun does and the slide Catch/Lock generally locks back further too. With a Partial Blowback Airgun the slide generally has a shorter range of movement back and forth on the frame with the slide locks usually about half of the distance compared to a Full Blowback Airgun.

View fullsize

The magazines are also very different as a Full Blowbacks Airgun generally has a partially exposed BB which is pushed into the barrel by the nozzle with each slide cycle. With a Partial Blowback Airgun the BB is generally not exposed and either the trigger action or simply the CO2 force is required to transfer the BB in the breach of the Airgun.

Another point to mention is that Full Blowback Airguns tend to use more CO2 and have a slightly lower velocity as compared to Partial Blowback Airguns but this is not a rule.

There are many types of magazines used in Airguns and some of this is dependent on the ammunition used.

For instance a stacked type of magazine often used for Steel BB and Airsoft can not be used for Pellets as pellets tend to deform when stacked in such a way since there is no metal casting protecting them from mashing into each other.

So what type of magazines do we generally see in Airguns? The most common Airgun magazines are as follows:

Simple Stick Magazine

• Mostly used with Steel BB but also found in some Airsoft Airguns.

• Some Pellet Airguns use a type of stick magazine with a rotary magazine on each end.

• Used in non-blowback and blowback Airguns.

• Can be made from plastic or steel or a combination of both materials.

Full Size Drop Out Magazine

• Used with Steel BB and Airsoft guns.

• Generally you will find these types magazines hold both the BB’s and CO2.

• Used in non-blowback and blowback Airguns.

• Commonly used with Airsoft Rifles in mid to high capacity.

• Can be made from plastic or steel or a combination of both materials.

Rotary magazine

• Used with Steel BB, Airsoft and Pellet Airguns.

• Used in non-blowback and blowback Airguns.

• Can be made from plastic or steel.

• Can often use mixed ammo types as in both 4.5mm Steel BB and .177 caliber pellet.

Belt Fed Magazine

• Like rotary magazine belt fed magazine can accommodate Steel BB, Pellet and Airsoft but are most often used with Pellet Airguns.

• Usually found in a full size magazine that also holds the CO2.

• Used in non-blowback and blowback Airguns.

• Can be made from plastic or steel or a combination of both materials.

Internal Magazine

• Used with Steel BB, Airsoft.

• Can have a hopper built in hat feeds a spring fed magazine.

• Usually found in lesser expensive Airguns but not a rule.

In this Video I go through each type of Airgun Magazine and talk about their differences and uses.

I have another Full Auto Fun Video this one focusing on 4.5mm Steel BB Versus 6mm Plastic and which one is better in terms of accuracy and shredding power. I perform this super scientific test by shooting obviously in full auto two comparable Steel BB and Plastic Airsoft Rifles at a paper target setup 20 feet away with a magazine as a backer so I can see what the accuracy is like and how much of the paper magazine gets shredded by each ammo being tested.

I have split this video into three separate videos, in video one I compare two similar AR styled rifles, a CO2 powered Blowback 4.5mm BB Rifle to a Gas Blowback 6mm Airsoft Rifle. In video two I compare two AK type Blowback Rifles to each otters, again a CO2 4.5mm Steel BB along with a Gas 6mm Airsoft.

And lastly in Video three I compare my top picks for each category which include a non-Blowback CO2 4.5mm BB Machine gun to an AEG 6mm Airsoft Rifle.

In this video (Video Three) the Airguns being used are the Original Baikal Drozd CO2 BB Machine Gun and the Tokyo Marui CQBR Block1 AEG Airsoft Rifle.

• Buy Airguns in Canada

• Buy Airguns in the US

I have another Full Auto Fun Video this one focusing on 4.5mm Steel BB Versus 6mm Plastic and which one is better in terms of accuracy and shredding power. I perform this super scientific test by shooting obviously in full auto two comparable Steel BB and Plastic Airsoft Rifles at a paper target setup 20 feet away with a magazine as a backer so I can see what the accuracy is like and how much of the paper magazine gets shredded by each ammo being tested.

I have split this video into three separate videos, in video one I compare two similar AR styled rifles, a CO2 powered Blowback 4.5mm BB Rifle to a Gas Blowback 6mm Airsoft Rifle. In video two I compare two AK type Blowback Rifles to each otters, again a CO2 4.5mm Steel BB along with a Gas 6mm Airsoft.

And lastly in Video three I compare my top picks for each category which include a non-Blowback CO2 4.5mm BB Machine gun to an AEG 6mm Airsoft Rifle.

In this video (Video Two) the Airguns being used are the Crosman AK1 CO2 Blowback BB and the WE AK74 UN GBB AIrsoft.

• Buy Airguns in Canada

• Buy Airguns in the US

I have another Full Auto Fun Video this one focusing on 4.5mm Steel BB Versus 6mm Plastic and which one is better in terms of accuracy and shredding power. I perform this super scientific test by shooting obviously in full auto two comparable Steel BB and Plastic Airsoft Rifles at a paper target setup 20 feet away with a magazine as a backer so I can see what the accuracy is like and how much of the paper magazine gets shredded by each ammo being tested.

I have split this video into three separate videos, in video one I compare two similar AR styled rifles, a CO2 powered Blowback 4.5mm BB Rifle to a Gas Blowback 6mm Airsoft Rifle. In video two I compare two AK type Blowback Rifles to each otters, again a CO2 4.5mm Steel BB along with a Gas 6mm Airsoft.

And lastly in Video three I compare my top picks for each category which include a non-Blowback CO2 4.5mm BB Machine gun to an AEG 6mm Airsoft Rifle.

In this video (Video One) the Airguns being used are the Crosman R1 4.5mm CO2 Blowback RIfle and the Tokyo Marui CQBR Block1 6mm Gas Blowback Airsoft Rifle.

• Buy Airguns in Canada

• Buy Airguns in the US

In this two part video series I compare several Air Pistols to each other to find out what type of round has the most power and accuracy. The guns I use for this not so scientific test are the KWC Model DE /50 Desert Eagle CO2 Blowback 6mm Plastic Airsoft Pistol, the EKOL ES 55 CO2 4.5mm Steel BB Pistol, the Umarex Magnum Research Desert Eagle Blowback CO2 .177 Caliber Pellet Pistol and the Umarex T4E TR50 CO2 .50 Caliber Paintball Pistol.

For this Video 2 Accuracy Test I shoot all of the above listed Airguns at a paper target setup 30 feet down range using a semi rested shooting position with my hands resting on a sand bag up front and seated on a stool in the back. It’s not perfect but works well enough. I didn’t take a ton of time with each gun since there where 4 to shoot in this Field Test Shooting Video so accuracy may have been a bit better if I took a little more time with each gun.

In Video 2 I test the power and penetration of each Airgun option shooting at a pop can, a soup can and a toilet paper roll so make sure to watch that video if you have not already watched it.

• Buy Airguns in Canada

• Buy Airguns in the US