In this Field Test Shooting Video I put the Webley Valuemax 22 Caliber Spring Piston Break Barrel Rifle through my standard Replica Airguns Indoor Field Test protocol by first testing out the velocity and placing 5 rounds through my Chronograph to see what the actual real world fps is using 14.3 grain lead pellets. I then setup a fresh paper target 30 feet downrange and place 10 pellets into it to see what type of grouping I can get. If you have not already watched my Table Top Video for this Break Barrel Spring Piston Pellet Rifle then make sure to do so for more details, specifications and close up video.
Starting off with my real world velocity test for the Webley Valuemax 22 Caliber Spring Piston Break Barrel Rifle, I went with 14.3 grain lead pellets which are I would say on the heavier side. Even so I managed to hit 478 fps which produced a nice 7.26 foot pounds of energy which by the way is almost 10 Joules! If you are wondering about Canadian legalities, as long as I do not go over 500 fps AND go over 4.2 foot pounds (both thresholds must be exceeded), then this Airgun is considered a non-regulated firearm and does not require a firearms license.
Moving on to the accuracy portion of my Indoor Field Test in the Replica Airguns Sea Can. As always I placed a brand new paper target 30 feet downrange and proceeded to shoot ten 14.3 grain lead pellets from a rested and seated shooting position to allow for best possible results with as little human error but I am imperfect so some human error is always present. I was using the open fiver optic sights on the Webley Valuemax 22 Caliber Spring Piston Break Barrel Rifle rather than a scope even thought there is a dovetail rail with included scope stop. To be honest I was expecting a better grouping, something close to half an inch but on this day with this ammo choice I was closer to 1.5 to even 2 inches. I did see several pellets land in a tighter sub group but some came out of this group enlarging the grouping. I would like to try a different pellet choice to see if I can do better as I believe this rifle has way more potential.
In terms of power the Webley Valuemax 22 Caliber Spring Piston Break Barrel Pellet Rifle is about has high as you can go before it becomes a regulated firearm here in Canada so no complaints in that department. Again I was disappointed in the accuracy but I honestly believe a different pellet choice could fix that problem as I have seen often with other Pellet Rifles. Once the right pellet choice is made and granted a more consistent and tighter grouping is achieved, this Spring Piston Pellet Rifle could make a decent small pest control airgun!
Type: Pellet Rifle. Distributer:Webley & Scott. Model:Valuemax. Materials: Metal and polymer build. Weight: 6.4 pounds (2900 grams). Barrel: 17.7 inches (450mm), rifled. Total Length: 43 inches (1092mm) Propulsion: Spring Piston Action: Break Barrel. Ammunition Type: .22 Caliber Pellets. Ammunition Capacity: Single Shot. FPS: 499.
Trigger Pull: The trigger pull on the Webley Valuemax .22 Caliber Spring Piston Break Barrel Rifle is fairly nice There is a little bit of very light take up followed by a vert light release , the take up or travel length can be adjusted on this Air Rifle but that is the only trigger adjustment you can make and perhaps all that is needed.
Accuracy: I have not performed my Field Test Shooting Video for the Webley Valuemax .22 Caliber Spring Piston Break Barrel Rifle but I did get to take around 20 or so shots with it when I was trying to get it to diesel for me. It looks ot me like it is going to be nice and accurate as I was not even really going for accuracy and it seemed to already be grouping fairly tight. I was recoding fps using my Chronograph as I was trying to find out if by adding some oil to the spring piston chamber could get it to diesel which it never did for me, I was however to establish that the Webley Valuemax .22 Caliber Spring Piston Break Barrel Rifle shot right around 470-480 fps using 14.3 grain lead pellets which worked out to right around 7.32 foot pounds of energy. I will know a lot more when I do my official Field Test Shooting Video next week.
Build Quality: Webley Valuemax .22 Caliber Spring Piston Break Barrel Rifle is built to be a value priced Airgun hence the name (Valuemax), that said it is maid well enough with lots of metal and of course some plastic or in this case mostly nylon as the stock is a solid nylon piece. Other than the stock the plastic parts are found to be in the sights and trigger guard, everything else seems to be metal.
Realism: The Webley Valuemax .22 Caliber Spring Piston Break Barrel Rifle is not a replica or copy of any real steel gun in production but it does look like a traditional hunting rifle in basic shape so make sure to transport thank airgun as if it was a real gun. Either in a gun case or perhaps a blanket in your trunk and always obey any laws for gun position and transportation in your area.
Pros:
Inexpensive price tag for well made decent performer.
Initial test showed to have good accuracy and power! (more to come).
Fully adjustable sights with optical TRUGLO Fiber Optics.
Can add a magnified optical scope using the top built in dovetail rail.
Nylon fiber stock is durable and functional with the addition of a vented rubber buttplate.
Trigger feels decent and is also adjustable for travel length.
Rear thumb safety resets after each break of the barrel.
Nice light and short single action trigger.
Would be good for small pest control because of decent FPS and good accuracy.
Cons:
Included sights are mostly plastic.
The Valuemax version has a more basic less adjustable trigger.
Detuned down to under 500 fps for Canada import as non-regulated Firearm.
Comments: I am looking forward to performing my Indoor Field Test Shooting Video for the Webley Valuemax .22 Caliber Spring Piston Break Barrel Rifle to see what it can really do in terms of accuracy so stay posted for that video next week. Overall if you are lucky enough to already have one or can get your hands on one since this rifle is discontinued in some area, I think this is a great Break Piston Air Rifle especially if you live in Canada and want the most bang for your buck. I am not only talking about cost verses features, I also mean power and energy since the Webley Valuemax .22 Caliber Spring Piston Break Barrel Rifle is a .22 caliber Air Rifle that can shoot really close to 500 fps with a nice heavy grain lead pellet achieving decent energy levels reasonable enough for small pest control. The Webley Valuemax .22 Caliber Spring Piston Break Barrel Rifle is not feature less, it does include a reseting safety, anti bear trap system, dove tail mounts with an included scope stop, fiver optic adjustable sights and a vert ergonomic textured nylon stock. All in all great value for what you pay!
My Vimeo Videos for the Webley Valuemax .22 Caliber Spring Piston Break Barrel Rifle:
In this Field Test Shooting Video I put the ASG Steyr Arms Scout Bolt Action Spring Airsoft Rifle through the regular Replica Airguns Indoor Field Test by first testing out the velocity and placing several rounds through my Chronograph to see what the actual fps is using both .20 gram and .40 gram Airsoft BB’s. Then I setup a fresh paper target 30 feet downrange and place 10 rounds into it to see how tight of a grouping I can get. If you have not already watched my Table Top Video for this Sniper Airsoft Riffle, then make sure to do so for more details, specifications and close up video.
Starting off with my real world velocity test for the ASG Steyr Arms Scout Bolt Action Spring Airsoft Rifle I decided to use both .20 and .40 gram Airsoft BB’s to see what a difference of double the weigth form the claimed for would actually be since for the most art this Airsoft Sniper Rifle is really meant to be using heavier Airsoft BB’ closer to the .40 gram weight. I was kind of expecting the heavier .40 gram BB’s to shoot almost half as fast since they where double the weight bu this was not the case! I shot 5 rounds with each weight Airsoft BB and with the .20 gram I averaged 479 which was actually faster than claimed, When I switched up to the .40 gram Airsoft BB’s I was surprised to get an average of 373 so only around 100 fps slower!
Moving on to the accuracy portion of my Indoor Field Test here in the Replica Airguns Sea Can, as always I placed a fresh paper target 30 feet downrange and proceeded to shoot 10 .40 gram Airsoft rounds into it from a rested and seated shooting position to allow for best possible results with as little human error added in. I was using a 4x optical scope since the ASG Steyr Arms Scout Bolt Action Spring Airsoft Rifle has a the added rail on top just fo this purpose and I would imaging most people are going to want to add a magnified scope to this Airsoft Sniper Rifle rather than use the built in pop iron sights that by the way are not adjustable. I know 30 feet is not the range one would be shooting this rifle at but it’s all I have for an indoor shooting range and it will give us an idea of what we can expect shooting further out… as in a nice tight group at 30 feet is going to mean better accuracy than a spread out grouping art 30 feet. I will say the ASG Steyr Arms Scout Bolt Action Spring Airsoft Rifle probably got one of the best groupings for an Airsoft Rifle that I have tested at 30 feet placing all 10 rounds within about an inch to an inch an a half.
I would like to take this Airsoft Sniper Rifle outside and see what it can do at much further out ranges again using nice and heavy Airsoft BB’s when it gets a bit warmer and stops raining so much :) But for now my Indoor Field Test performed about as good of a result as I can expect. The ASG Steyr Arms Scout Bolt Action Spring Airsoft Rifle is a really well made which paid off in two it performed for me. I don’t really see any need to upgrade this Airsoft Sniper Rifle other than adding an optical scope and perhaps investing in some high quality Airsoft Ammo.
Type: Airsoft Rifle. Distributer:ASG. Model:Steyr Arms Scout. Materials: Metal and polymer build. Weight: 6.5 pounds (2950 grams). Barrel: 14.5 inches (368mm), non-rifled. Total Length: 39.5 inches (1000mm) Propulsion: Spring Piston Action: Bolt action repeater. Ammunition Type: .6mm plastic Airsoft BB’s. Ammunition Capacity: 32 round magazine. FPS: 443. Type: Black and Grey versions.
Trigger Pull: The trigger pull on the ASG Steyr Arms Scout Bolt Action Spring Airsoft Rifle is short light and crisp. Working the bolt precooks the trigger for single action only shooting allowing for just the release of the hammer. There is very little take up and no creep at all, just a nice light and predictable trigger pull.
Accuracy: I have not performed my Field Test Shooting Video for the ASG Steyr Arms Scout Bolt Action Spring Airsoft Rifle so stay posted for that. ASG claims around 4430 fps velocity with the preinstalled M140 spring, you can upgrade the spring all the way up to an M190 spring for even higher potential fps. In terms of accuracy I am also expecting good results so check back next week for my Indoor Field Test Shooting Video for the ASG Steyr Arms Scout Bolt Action Spring Airsoft Rifle.
Build Quality: The ASG Steyr Arms Scout Bolt Action Spring Airsoft Rifle is well built with lots of high quality component not only inside but also internally. You will find a metal barrel and receiver along with metal bolt, trigger and rear sight, the front sight is however plastic. I donate really thin k you will be using the pop sights all that much as they are not adjustable and this gun really begs for a nice optical scope. The nylon polymer stock has micro-texturing to help with the grip in all weather conditions.
Realism: The ASG Steyr Arms Scout Bolt Action Spring Airsoft Rifle is based on the real steel 7.62 NATO Steyr Scout and even incorporates the integrated folding bipod legs like the original. For the most part they look identical but you will find the actual magazine on the Airsoft version is placed further up the stock to allow for the feeding of the Airsoft BB’s which does make the actual inner barrel shorter by about 4-5 inches.
Pros:
Nylon Polymer stock with micro-texturing.
Railed metal receiver with laser-etched Steyr trademarks.
Integrated folding bipod legs on left and right sides of the stock.
Flip-up backup front and rear sights.
Accessory slot on bottom of stock for mounting of optional bipod rail.
Millet QD sling loop attachment points.
Front dummy magazine.
Rear dummy magazine with storage for a spare magazine.
Removable stock spacer pads for length-of-pull adjustment.
90 degree trigger with steel sear.
90 degree aluminum piston with dual glide rings and steel base.
Silent Air Brake piston head.
Silent cylinder head with shock-absorbing padding.
9mm stainless steel ball bearing spring guide.
Bore-up steel cylinder with 12.5% more air volume than stock cylinders.
Hop-up unit with both side-lever adjustment and TDC screw adjustment options.
Steel CNC-machined hop-up arm.
03mm tight-bore inner barrel.
60 degree Modify Predator enhanced hop-up bucking preinstalled (50 and 70 degree buckings available separately).
Compatible with VSR-spec inner barrels.
450 FPS with pre-installed M140 spring.
Can take up to a M190 spring with no upgrades needed.
Cons:
32-round magazine.
Recommended ammo: 0.36g BBs and above, 0.4g optimal.
Comments: I am looking forward to performing my Indoor Field Test Shooting Video for the ASG Steyr Arms Scout Bolt Action Spring Airsoft Rifle. I won’t be able to test it out perhaps as far range as I would like to since I will be shooting it in the Replica Airguns Indoor Shooting range which allows me to test at 30 feet. That should give me a good overall idea on at least what it may be capable of since if we can get a tight group at 30 feet we should also be able to get a tight group at longer ranges with proper hop-up and heavier BB selection. I do plan on placing a scope on the ASG Steyr Arms Scout Bolt Action Spring Airsoft Rifle to give it the best possible chance of performing at it’s best and really hope to see a good result from it.
My Vimeo Videos for the ASG Steyr Arms Scout Bolt Action Spring Airsoft Rifle:
In this Field Test Shooting Video I put the ASG Action Army T-11 Spring Powered Bolt Action Airsoft Gun through it’s paces by first testing out the velocity placing several rounds through my Chronograph, and then I setup a paper target downrange and place 10 rounds into it to see how tight of a grouping I can get. If you have not already watched my Table Top Video for this Airsoft Sniper Pistol/Rifle then make sure to do so for more details, specifications and close up video.
Starting off with my real world velocity test for the ASG Action Army T-11 Spring Powered Bolt Action Airsoft Gun, I decided to use .28 gram Airsoft BB’s for this entire Field test Shooting video so I was expecting to get somewhere between 20-25% slower fps velocity as compared to the standard tested .20 gram Airsoft BB’s. After placing around 6 shots through my Chronograph I averaged 328 fps which ended up being 18% slower than the claimed 400 fps made by ASG. I would image if I had used .20 gram Airsoft BB’s I may have even exceeded 400 fps.
Moving on to the accuracy portion of my Indoor Field Test here in the Replica Airguns Sea Can, as always I placed a fresh paper target 30 feet downrange and proceeded to shoot 10 rounds into it from a rested and seated shooting position to allow for best possible results with as little human factor added in. I was using a 4x optical scope since the ASG Action Army T-11 Spring Powered Bolt Action Airsoft Gun does not come with any type of sighting system included so I did have to sight it in initially. I did manage to get a nice 1.5 inch grouping fairly close to the bullseye but I did notice that if I angled the barrel down a bit, BB’s would roll out of the barrel which made me wonder if the hop-up was set high enough to engage a BB.
So I did my second test with the hop-up set in the middle range and this time BB’s did not fall out of the barrel when angled down. After the hop-up adjustment I did notice I was shooting a bit higher which is expected with more hop-up adjustment so if you are experiencing BB’s falling out of the barrel then make sure to adjust your hop-up a bit tighter.
All in all the ASG Action Army T-11 Spring Powered Bolt Action Airsoft Gun performed very well for me especially once I got the hop-up figured out. And I do think it makes for a really nice compact Sniper Rifle if bulkiness is a factor for you, if not then checkout the Rifle version of this gun with the more traditional but-stock and longer barrel.
Type: Airsoft Rifle. Distributer:ASG. Model:Action Army T-11. Materials: Metal and polymer build. Weight: 3.9/4.5 pounds. Barrel: 11.8 inches, non-rifled. Total Length: 34.7/43.3 inches Propulsion: Spring Action: Bolt action repeater. Ammunition Type: .6mm plastic Airsoft BB’s. Ammunition Capacity: 50 round magazine. FPS: 400-430. Type: Pistol and Rifle versions.
Trigger Pull: The trigger pull on ASG Action Army T-11 Spring Powered Bolt Action Airsoft Gun is light, short and crisp. There is virtually no take-up and the release point has no creep to it. I would say it is not too light but for sure one of the lighter trigger s I have tested on a Airsoft rifle.
Accuracy: I have not performed my Field Test Shooting Video for the ASG Action Army T-11 Spring Powered Bolt Action Airsoft Gun so stay posted for that. ASG claims around 400-430 fps velocity depending on the version which is kind of weird since both have the exact same barrel length internally and I would assume both use the same mechanical part throughout? I don’t have the rifle version to compare to but I will for sure test the velocity using my Chronograph for the pistol version when I do my Field Test Shooting Review along with accuracy performance.
Build Quality: The ASG Action Army T-11 Spring Powered Bolt Action Airsoft Gun is well built for sure, it feels really solid in the hadn't and has good overall weigth to it for it’s size. You will find lots of metal parts where they need to be as in the inner and outer barrel, receiver, bolt, trigger, magazine release and I am sure most mechanical internal parts. Fit and finish is also very good.
Realism: The ASG Action Army T-11 Spring Powered Bolt Action Airsoft Gun is not a replace of any gun I know of but does have tab least the pistol version does look like a sawn off shotgun more than a sniper rifle. The gun overall all is very modern and ergonomic looking but in terms of being a replica of any specific real steel gun in production I don’t know of any it would resemble?
Pros:
Top and bottom rails for lots of accessory add on options.
Can swap over to a rifle version by adding on an interchangeable but-stock.
Mock magazine allows for storage and transport of tools plus extras.
Safety switch is in a great location for right handed shooters.
Comes with included hand stop.
Solid construction with lots of metal parts where they are important.
Ability to add side rails.
Great option if you are looking for a more compact sniper rifle.
Comes in Pistol and Rifle versions.
Cons:
Has an orange tip.
Does not come with sights, will need to add some sort of optical or red dot sight.
Does not come with speed loader, would have been nice.
Comments: I am looking forward to performing my Indoor Field Test Shooting Video for the ASG Action Army T-11 Spring Powered Bolt Action Airsoft Gun. I won’t be able to test it out perhaps as far range as I would like to since I will be shooting it in the Replica Airguns Indoor Shooting range which allows me to test at 30 feet. That should give us a good overall idea on at least what it may be capable of since if we can get a tight group at 30 feet we should also be able to get a tight group at longer ranges with proper hop-up and BB selection. I like the option of being able to choose either the Pistol or Rifle version and both should perform about the same. Having the Pistol version will allow for a much more compact Sniper Rifle option much better suited for shooting in a variety of situations.
My Vimeo Videos for the ASG Action Army T-11 Spring Powered Bolt Action Airsoft Gun:
Make sure to watch my Table Top Video Review where I go into more detail about the specifications and details along with some nice close up video of the Umarex Fusion 2 CO2 .177 Caliber Bolt Action Pellet Rifle.
In this Vimeo Video Field Test Review I test out the Umarex Fusion 2 CO2 .177 Caliber Bolt Action Pellet Rifle in the indoor Replica Airguns Shooting Range to see how accurate it is and what kind fo velocity we can expect from it.
Starting with the velocity test I averaged out 8 rounds through my chronograph using 8.18 grain lead pellets using the dual 12 gram CO2 setup and I was able to average 445 fps which is not bad as these are mid grain weight pellets, lighter weight pellets would for sure get closer to the 490 fps claimed by Umarex. The temperate was about average room temp so not overly cold or warm.
Moving on to the accuracy test I placed all 9 rounds from the rotary magazine into a fresh paper target setup 30 feet away. I use a reseted seated position in the back with the Umarex Fusion 2 CO2 .177 Caliber Bolt Action Pellet Rifle resting on a sand bag up front and I was using the 4 power scope for this test which I setup earlier. My final result was for sure an under one half inch grouping, I did feel like I pulled one shot a little bit but I am sure this Airgun can get quarter inch groupings at 30 feet and I would expect half inch groupings at 50 feet so perfect for mid range small pest shooting.
Umarex does adversities this Air rifle as being very quiet but in Canada we are not allowed to have any type of suppressor even on airguns so I believe this Canada version has been disabled in that regard but the Umarex Fusion 2 CO2 .177 Caliber Bolt Action Pellet Rifle is fairly quiet for sure with its long barrel and slightly lower fps than the US version. Overall the Umarex Fusion 2 CO2 .177 Caliber Bolt Action Pellet Rifle is a lot of bang for the buck with the added 4x scope, included magazines that hold 9 rounds each and the ability to use either a dual 12 gram or single 88 gram CO2 setup. It also looks really cool and performs just as good!
Type: Pellet Rifle. Distributer:Umarex. Model:Fusion 2. Materials: Metal and polymer build. Weight: 6.5pounds (2948 grams). Barrel: 22.5 inches, rifled. Total Length: 40.3 inches Propulsion: 12 gram CO2 x2 or 88 gram CO2 x1 Action: Bolt action repeater. Ammunition Type: .177 caliber pellets. Ammunition Capacity: 9 round rotary magazine x2. FPS: 490.
Trigger Pull: The trigger pull on Umarex Fusion 2 CO2 .177 Caliber Bolt Action Pellet Rifle feels pretty good, it is fairly short and light having a claimed 3.5 pound release which is believable. You will need to obviously work the bolt for each shot that precooks the internal hammer/striker allowing for the short and light trigger.
Accuracy: I have not performed my Field Test Shooting Video for the Umarex Fusion 2 CO2 .177 Caliber Bolt Action Pellet Rifle so stay posted for that. Umarex has claimed a velocity of around 490 FPS for the Canada version I will be testing, the US version has a claimed velocity of up to 700 for those in the US purchasing this Rifle. I am sure the included 4x32 optical scope once setup will help in the accuracy department when I test this CO2 Air Rifle out on a paper target setup 30 feet down range.
Build Quality: The Umarex Fusion 2 CO2 .177 Caliber Bolt Action Pellet Rifle is a fairly low cost target pellet Rifle when you consider it comes with a decent optical scope along with two 9 round magazines but even so the build quality seems very solid coming in at 6.5 pounds. The stock is plastic of course but there is lots of metal where you want it to be as in the bolt, trigger, safety and most other mechanical parts.
Realism: The Umarex Fusion 2 CO2 .177 Caliber Bolt Action Pellet Rifle is not a replace of any gun I know of but does sport a very modern ergonomic look with its pistol grip and molded full stock. I like the built in picatinny rail which even though it does not offer any type of open sight configuration will allow for a variety of scope mounting options for near or far shooting.
Pros:
Low cost for a full featured Air Rifle with included scope.
Nice ergonomic modern looking design.
Ability to use either 12 gram or 88 gram CO2 cartridges.
Comes with 4x32 optical scope and all mounting hardware needed.
Come with two 9 round rotary magazines.
May be very quiet if the SilencAir technology is not disabled here in Canada?
Single action 3.5 pound trigger fells good.
Safety is large and easy to use.
M-LOK slots for mounting additional hardware.
Cons:
No iron sight option if you would prefer that.
Limited to under 500 fps (Canada version).
Not sure about the functionality of the SilencAir technology in Canada?
Comments: I am looking forward to performing my Indoor Field Test Shooting Video for the Umarex Fusion 2 CO2 .177 Caliber Bolt Action Pellet Rifle to see if it performs as good as it looks. I’ll probably use the duel 12 gram configuration for this test since I don’t plan on shooting 300 rounds with it for my testing. We should also find out if the SilencAir technology has been disabled or not with my Canada version but even so, a 500 fps Air Refile is not going to be all that loud either way at the end of the day. There are not a lot of Bolt Action multi shot pellet Air Rifles out there especially in this price range so I am really hoping it hits a home run when I test it so stay posted for that video…
My Vimeo Videos for the Umarex Fusion 2 CO2 .177 Caliber Bolt Action Pellet Rifle:
In this Preview Unboxing Video I do an Unboxing and take a quick look at three Bolt Action Rifles, two spring powered Airsoft Rifles from ASG and a dual CO2 powered Pellet Rifle from Umarex.
In this Replica Airguns Vimeo Field Test Shooting Video I put the KWC / Umarex Mod. 92 A1 andElite Force 1911 TAC CO2 Blowback Airsoft Pistols through my Indoor Sea Can Shooting Test. Fist I find out what the real world velocity is by placing 5 rounds through my Chronograph and average out the FPS. I then shoot 10 rounds on a paper target for 30 feet back using a semi rested shooting position, sand bag up front and seated in the back.
Starting with my velocity test for both CO2 Blowback Airsoft Pistols I made sure to use a brand new CO2 along with .25 gram Airsoft BB’s so a bit heavier than what was used for the official stats. Both Umarex Airsoft Pistols shot really similar velocities with the Umarex Beretta Mod. 92 A1 averaging 364 FPS and the Umarex Elite Force 1911 TAC averaging 365 FPS. If I had been using .20 gram Airsoft BB’s I am sure these numbers would have been closer to the claimed 400 or so FPS.
Moving on to the accuracy test again I performed this test which each Umarex CO2 Blowback Airsoft Pistol. The Umarex Beretta Mod. 92 A1 performed a little bit better than the 1911 with all 10 shots grouping within 1.5 inches and very well centered on the target. The Umarex Elite Force 1911 TAC did have a slightly wider grouping closer to 2 inches and was a lilt bit high on the target but center nicely left to right. Of course the full auto mode on the Umarex Beretta Mod. 92 A1 did not produce anything even close to a tight group but it is always fun shooting in full auto :)
All in all both of these KWC / Umarex CO2 Blowback Airsoft Pistols performed well for me in terms of meeting their expectations for velocity and accuracy. We have them in our online Replica Airguns Stores in either KWC Unlicensed or Umarex Licensed versions so take your pick!
In this Vimeo Replica Airguns Update Video I take a look at three CO2 Airguns, one is a 4.5mm Steel BB revolver distributed by Barra and two are CO2 Blowback Airsoft Pistols distributed by Umarex. All of these CO2 Airguns I have previously reviewed in slightly different versions either barrel length and finish or Steel BB as compared to 6mm Airsoft So checkout why other reviews on similar version Airguns.
The Barra Barra Schofield CO2 BB Revolver is a replica of the Schofield No. 3 single action revolver and utilizes 6 reloadable shells for a very realistic shooting experience. It is very solid in construction bing made mostly out of metal and weighs in at around 2.4 pounds. This version shots 4.5 mm Steel BBs at a velocity of up to 400 fps. It comes in a variety of barrel lengths and finishes so amen sure to have a look in our Online Replica Airguns Store for what we have available…
Next up from Umarex is the fully licensed Beretta Pietro Mod. 92 A1 CO2 Blowback Semi and Full Auto Airsoft Pistol, this product is distributed by Umarex but is made by KWC. Another solid metal pistol with a hefty 2.4 pound weigth that holds 21 rounds in its full size drop out metal magazine and offers both semi and full auto shooting at the flick of a switch!
Again from Umarex I showcase the Elite Force 1911 Tac CO2 Blowback Airsoft Pistol and like the Beretta Pietro it too is made in the KWC factory for Umarex. The 1911 Tac as the name suggest is a tactical version of the standard Colt 1911 but with some upgrades like a skeletonized hammer and trigger along with an ambidextrous safety, white dot sights front and back and a picatinny rail on the frame for add ons. You can expect velocity to be somewhere in the 400 fps range and the full size drop out metal magazine holds 15 Airsoft BB’s.
Type: BB Air pistol. Distributer: Crosman. Model:MAKO. Materials: Metal and polymer build. Weight: 1.71 pounds (775 grams). Barrel: 6 inches, non-rifled. Total Length: 8.6 inches Propulsion: CO2 x1. Action: Semi auto blowback, double action only. Ammunition Type: 4.5mm Steel BB's. Ammunition Capacity: 20 rounds. FPS: 425.
Trigger Pull: The trigger pull on the Crosman MAKO Blowback CO2 BB Pistol is a little on the heavy side since it is double action only and it is also longer again being double action only. That said it is fairly smooth and not super heavy which shoudl allow for decent action shooting. It would have been cane if the hammer could be engaged for single action shooting but the design of the Crosman MAKO Blowback CO2 BB Pistol does not allow for this and therefore the hammer is just for show in this case.
Accuracy: I have performed my Field Test Shooting Video for the Crosman MAKO Blowback CO2 BB Pistol which can be found here. I won’t get into too much detail but overall you can expect velocity to be in the 400 fps range with a brand new CO2 and accuracy was decent form 30 feet away but could be a bit tighter. I was surprised at how snappy the blowback action was for a light weight slide with a light spring in it.
Build Quality: The Crosman MAKO Blowback CO2 BB Pistol feels solid enough in the hand and the materials used I am sure are on par with most Airguns out there but the gun may come across as being on the cheaper side as it lacks some of the more full features of more realistic functioning blowback Airguns. Just don’t let that make you think it is not well made as it is well made and may even be more reliable over time..
Realism: The Crosman MAKO Blowback CO2 BB Pistol looks the part of a beretta M92 at first glance but when you get a little closer you can really tell it is an Airgun at heart which is not a bad thing since that’s exactly what it is. You will find working parts like the magazine release and slide catch release and the slide does function since it is a blowback Airguns but the Crosman MAKO Blowback CO2 BB Pistol does have that funny inner barrel that pops out of the front every time you pull the trigger and parts like the slide safety are moulded into the slide and the hammer is just for show.
Pros:
Fairly inexpensive.
High FPS rating for a blowback BB pistol.
Easy to see Fiber Optic front and rear sights.
Multi tone color scheme looks good.
Has a pleasing tactic look to it.
CO2 tab is nicely hidden inside grip under magazine but plate.
Double action trigger pull is long but not too firm.
Picatinny rail for adding accessories.
Notched grips for a firm hold (best for larger hands)
Has a working side catch release that locks back after the last shot.
Has a surprising decent blowback action to it.
Cons:
Slide action feels clanky.
Hammer is just for show, does not do anything, no single action shooting ability.
Grips are large and will be to bog for smaller hands.
Comments: All in all the Crosman MAKO Blowback CO2 BB Pistol is a fun inexpensive CO2 Blowback BB Pistol that surprised me a bit when I actual got to shoot it. I originally though ti would feel kind of cheap to shoot but the snappy and firm blowback action and higher fps than usually found on blowback Airguns was surprising! The fiber optic sights making lining up target super easy and for a double action only shooter the trigger is not too bad so if you're a Beretta and Crosman fan then perhaps this is the pistol for you.
My Vimeo Video for the Crosman MAKO Blowback CO2 BB Pistol:
In this Field Test Review Video I test out the performance of the Crosman MAKO Blowback CO2 BB Pistol to see what the real world velocity and accuracy is for this Crosman Blowback BB Pistol. Crosman States 425 fps which is fairly high for a Blowback Airgun so we’ll see if I can get close to it!
Starting with my Velocity Test, I place 5 rounds through my Chronograph using a brand new CO2 with Daisy Zinc coated 5.1 grain Steel BB’s and averaged 390 fps withy the fastest shot hitting 403 fps and the slowest shot going down to 384 fps. It was not super warm in the sea can so I imagine with a bit warmer temperature this number would have been a little bit higher, maybe just up and over 400 which is still impressive for a blowback BB Pistol.
Moving on to my accuracy test, I placed 11 shots (meant to shoot 10) on a fresh paper target 30 feet down range and was able to get all shots within about a 3 inch grouping slightly low and to the left of the bullseye but not far off. I was shooting from a seated position with my hands resting on a sand bag for stability but of course some human factor is involved here.
Overall the Crosman MAKO Blowback CO2 BB Pistol performed decent for a fairly low cost and basic Blowback Airgun. The Blowback action is crisp with a long but not super heavy trigger. I like the fiber optic sights that make lining targets up super easy on virtually any background you are shooting on. This Airgun does have a large grip so keep that in mind if you have smaller hands but other than that it is a really fun Airguns to shoot!
In this video I test out the Umarex S&W M&P 9 M2.0 Blowback CO2 BB Pistol to see what we can expect in terms of accuracy and velocity. I first shoot several rounds through my Chronograph to get an average fps fooled by an accuracy test where I shoot 10 rounds at a paper target setup 30 feet down range to see how tight of a grouping I can get and if the Airgun out of the box shoots relatively on target.
Starting with my Velocity Test I shot about 9 rounds through my Chronograph to get a 6 shot average using a brand new CO2. The first three shots seemed to be a bit low as the Umarex S&W M&P 9 M2.0 Blowback CO2 BB Pistol is brand new and this was probably the CO2 valve settling in a bit. After the first three shots all the rest of the shots where in the 350-360 fps ranges with an average of 359 fps, fairly close to the Umarex 375 claimed fps on the packaging.
Next I setup a brand new paper target 30 feet down range and placed 10 rounds carefully on it from a seated and rested shooting position. I was able to get close to a two inch grouping that was a bit to the left of the bullseye but well centered vertically. The sights are not adjustable so at least with this gun I would need to aim juts a little bit to the right to nail targets consistently.
Overall I am impressed with the Umarex S&W M&P 9 M2.0 Blowback CO2 BB Pistol, the fps was right in the ballpark giving better performance than most full blowback BB guns which will ams translate to more shots per CO2. The accuracy was also on point, it just would be nice if some of these lower coat airguns had adjustable sights to get them dead canter. I did find the trigger to be better than expected, it is a bit long as the first part of the trigger is used to shutle a BB into the breach for the magazine but usually this porting of the trigger pull can have a bit of friction to it, not the case with the Umarex S&W M&P 9 M2.0 Blowback CO2 BB Pistol as it felt really smooth. The actual trigger release does require a bit more force but once y9u figure it out the guns world well and would make for good action shooting.
Type: BB Air pistol. Distributer:Umarex. Model:Smith & Wesson M&P9 M2.0. Materials: Metal and polymer build. Weight: 1.45 pounds (658 grams). Barrel: 3.6 inches, non-rifled. Total Length: 7.5 inches Propulsion: CO2 x1. Action: Semi auto blowback, single/double action. Ammunition Type: 4.5mm Steel BB's. Ammunition Capacity: 18 rounds. FPS: 375.
Trigger Pull: The trigger pull on the Umarex S&W M&P 9 M2.0 Blowback CO2 BB Pistol is about medium weight and is on the longer side to allow for the internal mechanism that pushes a BB for the magazine into the breach of the gun with each pull of the trigger. This does add a bit of additional resistance especially when the magazine is full of BB’s. As the magazine empties the spring resistance becomes less and makes the friction on the trigger less noticeable. When the slide blows back this does cock the internal hammer/striker allowing for less trigger pull then if the hammer is not actuated but I would say the trigger feels more like a double action trigger than a single action trigger even though most shots will be fired in single action.
Accuracy: I have not performed my Field Test Shooting Video for the Umarex S&W M&P 9 M2.0 Blowback CO2 BB Pistol so stay posted for that. Umarex has claimed an velocity of around 375 FPS adn this Airgun shoudl be abel to achieve that with it’s partial blowback more effect use of CO2. In terms of accuracy well I guess we will find out when I make my shooting review…
Build Quality: The Umarex S&W M&P 9 M2.0 Blowback CO2 BB Pistol build quality is fairly decent , fit and finish looks good with not too much slide wiggle and the materials used are both metal and plastic or polymer that look to be good quality.
Realism: The Umarex S&W M&P 9 M2.0 Blowback CO2 BB Pistol in terms of looking like the real steel version of its counterpart is very close for sure, would be hard to tell without further investigation. Umarex has done a great job of making this Blowback Airguns look believable by covering the CO2 screw, recessing the barrel and even working the manual safety into the right side slide catch release. In terms of operation the Umarex S&W M&P 9 M2.0 Blowback CO2 BB Pistol functions as you would expect other than it can not be easily filed striped and the blowback operation does not cycle back as much as a full blowback gun would.
Pros:
Very accurate replica of the S&W M&P 9 M2.0.
Fairly accurate weight and feel to it.
Metal and plastic parts where you find them on the real steel version, fit and finish is good.
Working trigger and manual safety and working slide catch and release.
Full size dropout metal magazine that holds BB's and CO2.
Warning instructions are discreet under the trigger guard.
Recessed barrel and hidden CO2 screw for more realistic look
Fully Smith & Wesson licensed via Umarex.
Rail for add on accessories.
White dot sights for easy target acquisition.
Comes with three sizes of interchangeable grips S/M/L.
Higher fps and more shots per CO2 than full blowback versions.
Cons:
Not full blowback but uses partial blowback.
Manual safety worked into right side slide catch release (Maybe good, maybe bad).
Sight are not adjustable.
Trigger is more like a double action trigger.
Comments: Overall the Umarex S&W M&P 9 M2.0 Blowback CO2 BB Pistol makes for a nice replica Blowback Airgun version of the S&W M&P 9 M2.0. There are some compromises with this version mainly the partial blowback operation that does make the trigger a bit heavier and longer than a true single action trigger would be, the slide does not cycle as fully as expected either and y9ou can not easily field strip this version. That said the shorter blowback action and the way the BB is pushed forward into the breach before each shot means that the Umarex S&W M&P 9 M2.0 Blowback CO2 BB Pistol will have a high FPS and will also get more shots per CO2. So you decide what may be more important to you at the end of the day? True realism or better performance?
My Vimeo Videos for the Umarex Smith & Wesson M&P9 M2.0 CO2 Blowback BB Pistol:
UPDATE: All Umarex Glock 17 Gen 4 and Glock 19 Gen 3 GBB Airsoft Pistols now ship with the Shorter Barrels!!
In this Field Test Shooting Video I test out the Umarex Glock 17 Gen 4 GBB Airsoft Pistol in the Replica Airguns Indoor Sean Airgun Shooting range. This product now comes with the longer sticking out barrel to increase the FPS for import into Canada to get it up and over the 360 FPS requirement using a .20 gram Airsoft BB. In my previous video I test out the Umarex Glock 19 Gen 3 GBB Airsoft Pistol but swapped out the longer barrel for the shorter barrel to see how much the sorter barrel reduces velocity and also if there is an impact on accuracy? Make sure to watch that video to get the scoop on the shorter barrel with both the Umarex Glock 17 dam Glock 19 GBB Airsoft Pistols
For the velocity portion of this test I placed several .25 gram Airsoft BB’s through my Chronograph and was please to get a very consistent 355 average FPS reading which is very close to the claimed 360 FPS when using .20 gram Airsoft BB’s so if I had been using a lighter BB I would have for sure seen velocity up and over the 360 FPS.
In terms of accuracy the Umarex Glock 17 Gen 4 GBB Airsoft Pistol also performed really well, maybe not as well as the short barrel Glock 19 Gen 3 I tested just last week that seemed to group just a little bit tighter and was a little bit more well vented on the target. Both the Glock 17 and Glock 19 shot a bit low but I am sure a slight hop-up tweak could rectify that. I did however manage to get around a 2 - 2.5 inch 10 shot grouping.
So in summary both the Umarex Glock 17 Gen 4 and Glock 19 Gen 3 GBB Airsoft Pistols at least for now come with the longer barrels only and so you options are to either cut down the existing barrel or buy a shorter barrel and replace it, that is unless you like the look of the long sticking out barrel ;) You will get a velocity drop of around 75 FPS with the shorter barrel installed but I would say accuracy should be about the same at the end of the day.
UPDATE: All Umarex Glock 17 Gen 4 and Glock 19 Gen 3 GBB Airsoft Pistols now ship with the Shorter Barrels!!
In this Field Test Shooting Video I test out the Umarex Glock 19 Gen 3 GBB Airsoft Pistol in the Replica Airguns Indoor Sean Airgun Shooting range. This product now comes with the longer sticking out barrel to increase the FPS for import into Canada to get it up and over the 360 FPS cut off using a .20 gram Airsoft BB. I wanted to see how much of a difference the shorter barrel would make so I will be comparing the short barrel with the long barrel to find out the FPS and accuracy differences. In the Video I only shoot the Umarex Glock 19 Gen 3 GBB Airsoft Pistol with the short barrel but in my next video I Shot the Umarex Glock 17 Gen 4 GBB Airsoft Pistol with its included long barrel for comparison.
For the velocity portion of this test I placed 5 .25 gram Airsoft BB’s through my Chronograph and was please to get a very consistent 276 average FPS reading with the slowest shot hitting 274 FPS and the fastest shot hitting 278 FPS so really close. Keep in mind I was using .25 gram Airsoft BB’s rather than .20 gram Airsoft BB’s so I would imagine the Umarex Glock 19 Gen 3 GBB Airsoft Pistol even using the shorter barrel should hit closer to 300 FPS with the lighter Airsoft BB’s.
In terms of accuracy the Umarex Glock 19 Gen 3 GBB Airsoft Pistol also performed really well, I did not make any adjustments to the gun after installing the shorter barrel not even to the hopup. I was pleased to see a fairly well centered 10 shot grouping mostly within a 2 inch grouping with perhaps one flyer extending that group to about 2.5 inches. All shots where well centered left to right but just a light bit under the target, a quick hopup adjustment should rectify that.
My next Vimeo Video will be focusing on the Umarex Glock 17 Gen 4 GBB Airsoft Pistol with its included long barrel to see what kind of velocity gains we get for it and if the longer barrel helps with accuracy at all so look for that video early next week!
UPDATE: All Umarex Glock 17 Gen 4 and Glock 19 Gen 3 GBB Airsoft Pistols now ship with the Shorter Barrels!!
Type: Blowback GBB Airsoft Pistols. Manufacturer: Distributed by Umarex. Model:Glock 17 Gen 4 & Glock 19 Gen 3. Materials: Metal & Polymer. Weight: 1.66 Pounds (642 grams) / 1.64 Pounds (634 grams). Barrel: Smooth bore 10.8 inch barrels. Propulsion: Green Gas or Propane. Action: Semi auto blowback, single action only trigger. Ammunition Type: 6mm plastic Airsoft BB's. Ammunition Capacity: 22 / 19 round drop out full size metal magazines. FPS: Claimed 410 with .20 gram Airsoft BB’s.
Trigger Pull: The trigger pull on the Umarex Glock 17 Gen 4 and Glock 19 Gen 3 GBB Airsoft Pistols is fairly short with only a little bit of take up, the release is light and crips. The blowback action resets the internal Hammer / Striker with each shot for that true single action trigger and it’s also nice that the trigger does have a working trigger safety like the real steel versions.
Accuracy: At this point I have not shot either of the long barrel Umarex Glock 17 Gen 4 and Glock 19 Gen 3 GBB Airsoft Pistols so I can only quote what Umarex is saying in terms of FPS which is around 410 using Green Gas or Propane. These longer barreled versions should shoot fairly hot compared to the much shorter barreled versions and since i do have a short barrel Glock 17 Gen 4 I may also compare it at the same time to see what the actual barrel length does in terms of fps velocity. Of course my Field test Shooting video will also focus on accuracy add see what can be accomplished shooting a 10 shot grouping at 30 feet down range.
Build Quality: TheUmarex Glock 17 Gen 4 and Glock 19 Gen 3 GBB Airsoft Pistols seems well made overall. It does seem a little bit underweight but still feels solid enough in the hand, Glocks are not known for being all that hefty. The Slide is metal but has a bit of an unusual finish that makes it look a lot like the plastic frame rather than a more shiny metal look. All the parts seem to fit nicely, maybe even a bit snug at first as I noticed the side had a bit of friction to it but seems to be working in nicely now.
Realism: The Umarex Glock 17 Gen 4 and Glock 19 Gen 3 GBB Airsoft Pistols look the part of these Glocks all day long. Other then the slightly lighter weight it would be hard to tell off hand until you remove the magazine and take a closer look. All the parts work as you would expect them to, similar to the real steel version and you can even fully field strip the them which makes getting to and adjusting the hop-up easy enough to do. Available From: The Replica Airguns Store.
Pros:
Decent weight and feel to them, build quality seems good.
Really nice looking replicas of the original Glock 17 Gen 4 / Glock 19 Gen 3.
Fully Glock licensed via Umarex.
Easy to see white dot sights front and back with rear sight adjustable for windage.
Recessed barrel for added realism when cut down.
Accessory rail for adding a laser or tactical light.
Full size drop out metal magazines that holds the Green Gas and 6mm Airsoft BB’s.
Warning instruction are nice and discreet under trigger guard.
Nice light SAO trigger as the blowback action pre-cocks the internal hammer/striker.
Working trigger safeties.
No red tips and more realistic outer barrel size.
Cons:
Only comes with the longer barrel so you need to either cut it down or replace it with a shorter barrel.
No way to put a mock suppressor on it to keep extended barrel.
Comments:
Getting the Umarex BB versions of the Glock 17 and Glock 19 has for sure been a bit easier since fps velocity is not a factor. So it’s great that we at least have a way to import these two Umarex Glock GBB Airsoft Pistols into Canada! Yes some home modifications may be required to cut down the inner barrel as the long extended barrels are certainly not practical for every day shooting. That said with the extended long barrels I did get out and shoot a few rounds through them and the added barrel length really does allow for a much faster velocity Airsoft BB making these Umarex GBB Airsoft Glocks more like snipper pistols :)
UPDATE: All Umarex Glock 17 Gen 4 and Glock 19 Gen 3 GBB Airsoft Pistols now ship with the Shorter Barrels!!
In this YouTube Update Preview Video I go over a couple new Umarex Glock Licensed GBB Airsoft Pistols that I feel require a bit of explaining. Essentially we already stock these same Umarex Glock Blowback Airsoft Pistols, but in the CO2 magazine versions. The Umarex Glock 17 Gen4 and Umarex Glock 19 Gen3 I highlight in this video come with Green Gas Magazines and both have extended inner barrels to allow for Canada import to increase the velocity to our over 360 fps using a .20 gram Airsoft BB.
Usually Green Gas Airsoft Pistols with extended inner barrels will have the ability to unscrew the extension and will even come with a shorter replaceable barrel but in this case all you get is the longer one piece inner barrel. My suggestion is to either cut down the long inner barrel to fit within the out barrel or purchase a short inner barrel when they are available.
At the moment we do not have either one of these Airsoft Pistols listed in our Replica Airguns Stores but they should pop up shortly!
In this Preview Update Video three newer products, two Umarex Airsoft CO2 Blowback Pistols and one CO2 Blowback BB Pistol from Crosman. This is far from a full review which I will remaking for all of these Airguns in the near future. I simply go over some of the main specifications and show you quickly around each Airgun.
