In this Field Test Shooting Review I test out the Umarex S&W M29 8 Inch Barrel Shell Loading CO2 BB Revolver in the Replica Airguns Sea Can Indoor Shooting Range to find out its velocity and accuracy using both 4.5mm Steel BB’s and .177 Caliber Lead Pellets. The version I am using is the BB version but my viewers have informed me that the BB version may in fact shoot just as well as the pellet version using pellets even without the rifled barrel due to how pellets are shaped not always requiring a rifled barrel to fly true. So let’s find out!
Starting with the velocity test, I shot 4 rounds of each ammo through my Chronograph using a fresh CO2 cartridge. Umarex claims the Umarex S&W M29 8 Inch Barrel Shell Loading CO2 BB Revolver is able to get a maximum fps of 420 using standard 4.5mm steel BB’s and I was able to average 396 so every close. In warmer conditions 420 fps should be possible. Switching to the .177 caliber lead pellets the fps lowered a bit to an average of 323 fps as expected since the pellets are much heavier (around 7 grain versus 5 grain). I would expect the energy of the pellets to be a bit higher and also keep that energy out to further ranges so if you plan to shoot longer ranges perhaps go with the lead pellets over the BB’s as long as they are similar in accuracy which I test next.
For the accuracy portion of the test I again started off with the 4.5mm Steel BB’s and fired 6 rounds into my paper target setup 30 feet down range. I shot the Umarex S&W M29 8 Inch Barrel Shell Loading CO2 BB Revolver using a seated shooting position with my hands resting up front on a sand bag to help with stability but it’s not perfect and there is always some human factor to consider. That said I was able to shoot a 1.5 inch 6 shot grouping with the BB’s and if I remove one outlier from the group that reduced it to closer to around an inch so not too bad for a BB shooter. I then switching up to the .177 caliber lead pellets and was a bit surprised that even without a rifled barrel the pellets seemed to perform better than the Steel BB’s getting a solid 1 inch grouping with no real outliers in it!
Unfortunately I do not have the actual rifled barrel version of the Umarex S&W M29 8 Inch Barrel Shell Loading CO2 Revolver. Perhaps in the future I can compare the BB verso to the Pellet version using pellets to see if there is an improvement with the addition of the rifled barrel. I can say the BB version without the rifled version shoots pellets just fine at least up to 30 feet so feel free to shoot whatever ammo you want to with it and not be worried about compromising accuracy or velocity.
Trigger Pull: The trigger pull on the Cybergun Licensed L6 .50AE Desert Eagle GBB Airsoft Pistol is single action only which means you will need to rack the slide to not only draw the hammer back but to also chamber the first round. After that the blowback action will do this for you until you are out of ammo and then the slide will lock back. The trigger itself is really nice, it’s light, short and has a crisp release perfect for fast action shooting.
Accuracy: At this point I have not made my Field Test Shooting portion of my review for the Cybergun Licensed L6 .50AE Desert Eagle GBB Airsoft Pistol and I really don’t know what to expect? Cybergun claims an fps of 368 using green gas or propane but this may be on the high side since green gas generally produces less velocity than CO2. In terms of accuracy, again I have no idea since I have not reviewed this version of Desert Eagle before. So stay posted till next week when I make the Field Test Shooting Review for it.
Build Quality: Overall the all metal build quality of the Cybergun Licensed L6 .50AE Desert Eagle GBB Airsoft Pistol is good which I would hope to be the case for a higher priced Airsoft Pistol like this. I did however notice under the slide there was a bit of a rough area that I feel could have been sanded or polished out a bit better. Other than that this gun looks amazing and the fact that both the slide and receiver are both metal gives this Airsoft gun good weight and feel.
Realism: The Cybergun Licensed L6 .50AE Desert Eagle GBB Airsoft Pistol is an excellent Replica Airsoft version of the real steel L6 .50AE Desert Eagle including the top and bottom rails and the ported front barrel. It also has full blowback action and you can fully field strip it. Combine that with an all metal build and it doesn't get any more realistic than that.
Pros:
Full metal build, close to true weight of real steel version.
Nice gold or silver Electroplated finish.
Realistic full blowback action.
Fully Licensed via Cybergun.
Rails on top and bottom for adding accessories.
Nice light and short single action trigger.
Injection molded polymer grip panels with Desert Eagle markings.
Realistic field strippable.
Full size drop out metal magazine.
Adjustable Hop-up to adjust elevation and accuracy at range.
Cons:
Comes with red/orange tip installed.
Price is on the higher side.
This version is not full auto.
Comments: Going off just the looks and feel for the Cybergun Licensed L6 .50AE Desert Eagle GBB Airsoft Pistol I can say it is for sure one of the nicest Desert Eagles I have reviewed to date. I’m not generally a fan of gold guns but I think gold really suits the Desert Eagle since this iconic pistol is known for being over the top. It’s also full metal as compared to the KWC versions so that’s a big plus. I guess it will come down to how well it performs during my Field Test Shooting Video in terms of power and accuracy. If it doesn't let me down here, it may just be worth the nearly $400 piece tag!
My Table Top Video of the Cybergun Licensed L6 .50AE Desert Eagle GBB Airsoft Pistol:
Type: BB Pistol. Manufacturer: Umarex. Model: M29. Materials: Metal & plastic. Weight: 2.5 pounds (1135 grams). Barrel Length: 8.375 inches (Smooth bore). Total Length: 12.13 inches. Propulsion: 12 gram CO2 cartridge. Action: Revolver, single and double action. Ammunition Type: 4.5mm steel BB's (Also available in 6mm Airsoft). Ammunition Capacity: 6 rounds. FPS: 420fps claimed.
Trigger Pull: The trigger pull on the Umarex S&W M29 8 Inch Barrel Shell Loading CO2 BB Revolver is light in single action but not too light, there is virtually no take up and the release is predictable. In double action the trigger pull is heavier as the cylinder and hammer are both actuated manually by the trigger but even so the pull is not what I would call heavy for a double action revolver. The double action trigger pull is nice and even and will not tire out your finger too much firing all six rounds quickly.
Accuracy: At this point i have not made my Field Test Shooting portion of my review for the Umarex S&W M29 8 Inch Barrel Shell Loading CO2 BB Revolver but I expect to get close to the 420 fps claimed velocity and I also expect to shoot around a 1 to 2 inch grouping based on my past experienced with similar Shell Loading BB Revolvers. I may even pull of a 1/5 inch group if I am on my game and so is the gun… We will have to all wait till next week when I record the shooting portion of my review for the Umarex S&W M29 8 Inch Barrel Shell Loading CO2 BB Revolver.
Build Quality: Overall the all metal build quality of the Umarex S&W M29 8 Inch Barrel Shell Loading CO2 BB Revolver is very good. The black chrome finish looks really nice but does show every finger print and any grease from your hands. The imitation wood grips look just like real wood and with only the exception of a small scratch or crack in the front plastic red sight, the Umarex S&W M29 8 Inch Barrel Shell Loading CO2 BB Revolver was flawless.
Realism: The Umarex S&W M29 8 Inch Barrel Shell Loading CO2 BB Revolver is the same revolver used in one of the Dirty Hariy Movies and really looks exactly the same. As with all the shell loading BB/pellet/Airsoft Revolvers, they look and perform exactly like the real steel versions other than recoil of course. The only give away for the Umarex S&W M29 8 Inch Barrel Shell Loading CO2 BB Revolver would be the diameter of the shells as Umarex decided to repurpose the 38/357 shells used in their other smaller caliber shell loading revolvers. It would have been nice to have a larger 44/45 caliber sized shell that they could use in both the Colt 45 Single Action Army Revolvers and this 44 Magnum version of the Smith and Wesson M29 Revolver. The barrel opening is closer to that of a 44 Magnum so they did get that part right.
Pros:
Classic iconic 44 magnum movie revolver.
Mostly all metal build.
Good overall weight, it’s big so expected to weigh a fair amount.
Lots of detail, well made, fit and finish is very good.
Fully S&W Licensed via Umarex.
Love the black chrome look but prone to finger prints.
Simulated wood grips look real enough.
Should have good overall power, accuracy and shots per CO2 (claimed around 80 per CO2).
Adjustable rear sight for windage/elevation with red dot front sight.
CO2 Allen key built into grip.
Recessed barrel true to 44 magnum opening size.
Nice Trigger pull in both single and double action.
Cons:
Shells are closer to 357 not 44 magnum in size.
Don’t like the white writing on the right side.
Black chrome finish shows lots of finger prints and grease.
Comments:
I really like that Umarex decided to give us this more classic Revolver to add to our collection of Airgun Revolvers! I was a big fan of the Dirty Harry Movies so this gun is for sure going to be part of my Airgun collection and even if you are not a fan, you should probably be a fan of the Smith and Wesson M29 which was considered to be one of the most powerful revolvers back in its day. Right now you can get it in 4.5mm Steel BB and 6mm Plastic Airsoft but hopefully there is a .177 caliber Pellet version on its way at some point.
My Table Top Video of the Umarex S&W M29 8 Inch Barrel Shell Loading CO2 BB Revolver:
I have a nice Airgun Pistol Update Unboxing video to checkout where I take a look at 5 Airguns four of which are Gas Blowback Airsoft Pistols and one is a CO2 BB Revolver. I don’t go into a lot of details here on each Airgun as this is mainly just a preview video to let everyone know we have these products in our Online Replica Airgun Stores and give a you a quick look at them. I will be following up with individual Table Top and Field Test Videos where I go into more details and also show you how each gun performs in the Replica Airguns Indoor Sea Can Shooting Range.
Yet another Field test Shooting review for the Crosman AR line of CO2 BB Blowback Full Auto Machine Guns. Today I test out the Pistol version or A4-P model. Basically this is the same BB Gun mechanically as all the other Crosman AR’s but with some cosmetic differences which can affect power and accuracy a bit. And that would be a slightly shorter barrel which can reduce velocity and the lack of a but stock for less stability.
As always I first test out the power or velocity for the Crosman A4-P CO2 Blowback BB Machine Gun, I always use brand new CO2 and make sure the temperature is not too cold in the Replica Airguns Sea Can. Crosman claims around 400+ fps for the Crosman A4-P CO2 Blowback BB Machine Gun and in my Chronograph test I was able to get a 5 shot average of 357 fps. The temperature was not super warm so I would expect on a hot summer day to get closer to 400 fps so pretty close.
I then proceeded to see what kind of accuracy I could get from the Crosman A4-P CO2 Blowback BB Machine Gun shooting 10 rounds in semi auto at a paper target setup 30 feet down range. I use a stabilized shooting position with the Airgun resting on a sand bag up front and me sitting on a stool in the back so the lack of a stock was not a huge drawback here. Regular stand up shooting and not being able to shoulder this Airgun as easily will mean a difference for sure. In semi auto mode with 10 rounds I was able to get around a 2 inch group but I would say this BB Machine gun should get closer to a 1 inch grouping as 8 out of the 10 rounds where all within 1 inch of each other so perhaps some human error on my part was at play here. Just for fun I unloaded the last 15 rounds in full auto on the unsuspecting target and as expected the grouping widened to around 4-5 inches.
Personally I prefer the Crosman AR Full Auto BB guns with a rear stock for that added extended shoulder support but the Crosman A4-P CO2 Blowback BB Machine Gun will fit much better into a back pack if you want to take it out in the woods for some shooting fun. Not everyone has a proper backyard or indoor range to use! the Crosman A4-P CO2 Blowback BB Machine Gun is also one of the coolest looking in this lineup so that has to count for something ;) I wonder what Crosman has planned for their line of Full Auto BB Machine guns now that they have several AR versions and even the AK1. Maybe an MP5 or a SCAR?
Type: BB Pistol/Rifle. Manufacturer: Crosman. Model: A4-P. Materials: Metal & plastic. Weight: 5.3 pounds (2.4 kilograms). Length: 21.2 inches. Propulsion: 12 gram CO2 dual cartridges. Action: Blowback - Semi & full auto, single action only. Ammunition Type: 4.5mm steel BB's. Ammunition Capacity: 25 rounds. FPS: 430fps. Rate of Fire: 1400 rounds per minute in full auto
Trigger Pull: The trigger pull on the Crosman A4-P CO2 Blowback BB Machine Gun is single action only since the charging handle must be cocked first before you can shoot it. The trigger is short and fairly light as you would expect from an AR type trigger action. The real fun happens with the Crosman A4-P CO2 Blowback BB Machine Gun when you switch it over to full auto mode and with just one pull and hold of the trigger you empty the 25 round magazine in mere seconds. You may want to pickup the Crosman High Capacity magazine if you plan on doing a lot fo full auto shooting!
Accuracy: I have not made my Field Test Shooting Video just yet but you can checkout my Field Test Shooting Video for the Crosman R1 CO2 Blowback BB Machine Gun which is a very similar product to the Crosman A4-P CO2 Blowback BB Machine Gun. I test out the Crosman R1 CO2 Blowback BB Machine Gun using my Chronograph where I get an average of 385 fps and a nice 30 foot grouping of right around 1 inch in semi out and a decently tight full auto group of about 3-4 inches. We should expect about the same with the Crosman A4-P CO2 Blowback BB Machine Gun as long as not being able to shoulder it is a big factor?
Build Quality: The Crosman A4-P CO2 Blowback BB Machine Gun is well made all around just like the rest of the Crosman AR series of BB Machine Guns. Weighing in at 5.3 pounds without any add on accessories it feel solid and well built. There is a lot of metal going on inside and out of this rifle but keep in mind the top and bottom receiver are plastic with metal parts where they need to be like in the internals, pretty much all the working parts are metal, the magazine is full metal, the buffer tub is metal, charging handle, selector switch, magazine release, bolt release, trigger and of course the barrel is metal.
Realism: The Crosman A4-P CO2 Blowback BB Machine Gun is about as real as you are going to get in a CO2 Blowback AR/M4 styled Airgun. You can even take it apart and split the top and bottom receivers like the real steal version. The blowback action gives you some recoil but more importantly offers a true single action trigger and of course the full auto ability we all love. Almost all the working parts work like they would on a real AR / M4 other than the forward assist which is moulded into the receiver. Keep in mind this is the pistol version but like other AR styled “Pistols” the buffer tube area is still required to make the action work.
Pros:
Super realistic working M4/AR 4.5mm BB Rifle just like the other Crosman Rifles in this lineup.
Full blowback operation with both semi and full auto shooting, can feel the blowback operation rocking the gun.
Great weight and feel to it.
Almost everything works exactly like the real steel version. (Charging handle, dust cover, bolt release, magazine release, selector switch).
Duel CO2 metal drop out magazine that holds the 25 4.5mm steel BB’s as well as the dual CO2.
Compact maneuverable pistol version but may be able to add an AR butt stock if you want?
Included red dot sight and ability to add pop-up iron sights.
Lots of rails for mounting additional cool hardware.
Removable flash hider.
Works with Crosman High Capacity magazine.
Cons:
Receiver is plastic but well made and does not compromise feel or weight since there is lots of metal throughout this gun.
No iron sights included.
No but stock included.
Comments:
The Crosman A4-P CO2 Blowback BB Machine Gun is really pretty much the same as the Crosman DPMS SBR and Crosman MPW and Crosman R1 CO2 Blowback BB Machine Gun with more or less Cosmetic changes, most notably being the lack of a butt stock and being more of the pistol version. Like the otters Crosman AR products, the Crosman A4-P CO2 Blowback BB Machine Gun has an AR compatible pistol grip, adn like the Crosman R1 CO2 Blowback BB Machine Gun you also have the ability to change out the flash hider, you can even put a mock suppression on in it if you choose to. No matter which of the Crosman AR Full Auto CO2 BB Rifles you chooses to get they are mechanically every similar and share most of the same parts. If you want the most compact version than the Crosman A4-P CO2 Blowback BB Machine Gun is the way to go!
My Table Top Video of the Crosman A4-P CO2 Blowback BB Machine Gun:
In this Field Test Shooting Video I put some .20 gram Airsoft BB’s through the Action Army AAP-01 GBB Airsoft Pistol to see what the actual velocity is compared to the claimed fps. I also put 10 rounds into a paper target setup 30 feet downrange to find out just how accurate and what kind of grouping I can get from this Gas Blowback Airsoft pistol and also do a full mag dump! If you have not already watched my Table Top Review for the Action Army AAP-01 GBB Airsoft Pistol then make sure to watch if for more specifications and details along with some nice close up video.
For my Chronograph test I placed 5 rounds through my Chrony using .20 gram plastic Airsoft BB’s and was able to average 314 fps with the short barrel and 385 fps with the longer barrel extension added. I was surprised with the addition 70 fps just by adding an extra 4 inches or so to the barrel.
For the accuracy portion of my Field test Shooting Video for the Action Army AAP-01 GBB Airsoft Pistol, I ended up first placing 10 rounds into a fresh paper target setup 30 feet down range. I was using my standard seated and rested shooting position which does offer a fairly stable shooting platform but not without some degree of human interaction. I was a little bit disappointed in the grouping I got as it was one of the larger groupings I have gotten for a test like this spreading out to at least 5-6 inches, still perfectly fine shooting at human target 30-40 feet away. I then uploaded up a full magazine with BB’s and gas and did a mag dump on the same target. As expected there was a lot fo gas and a lot ammo spraying everywhere but the Action Army AAP-01 GBB Airsoft Pistol did make it through the full 22 rounds and get at least some of them on the target.
The Action Army AAP-01 GBB Airsoft Pistol may not be the most accurate GBB Airsoft Pistol out of the box but does offer both semi and full auto and at the end of the day when using this Airsoft Pistol in an actual game situation the accuracy will be not as important since your target will generally be a human torso which is much larger than the 5-6 inch grouping I got. I’m not sure how useful the full auto feature really is in a real world situation but it sure is fun and maybe if you pair up a higher capacity G-series magazine this compact full auto pistol could work as a nice min machine gun!
In this Field Test Shooting Video I put some lead pellets through the Umarex Ruger Mark IV Break Barrel .177 Cal Pellet Pistol to see what the real world velocity is compared to the claimed fps. I also put 7 rounds into a paper target setup 30 feet downrange to find out just how accurate and what kind of grouping I can get from this compact spring piston replica air pistol! If you have not already watched my Table Top Review for the Umarex Ruger Mark IV Break Barrel .177 Cal Pellet Pistol then make sure to watch if for more specifications and details along with some nice close up video.
For my Chronograph test I placed 5 rounds through my Chrony using 8.18 grain Sig Sauer Match Precision Wadcutter Lead Pellets and was able to average 312 fps so just shy of the claimed 320 fps but there are lighter lead pellets out there and even lighter alloy pellets so higher fps can be achieved with this Air Pistol if you plan on using lighter pellets.
For the accuracy portion of my Field test Shooting Video for the Umarex Ruger Mark IV Break Barrel .177 Cal Pellet Pistol, I ended up placing 7 rounds into a fresh paper target setup 30 feet down range. I was using my standard seated and rested shooting position which does offer a fairly stable shooting platform but not without some degree of human interaction. I was a little bit disappointed in the 2 inch grouping I got, I was expecting closer to a 1 inch group but I would have had to have been on my game and maybe today I was not. Pellet choice can also effect accuracy for sure and so maybe a different pellet would have performed better in this test. Most of the variable was up and down not left to right with only about an inch side to side.
All in all the Umarex Ruger Mark IV Break Barrel .177 Cal Pellet Pistol did a good job hitting velocities as claimed and producing a decent grouping that I feel I could have improved upon once I got use to the lighter firmer trigger than I would like to see on a Ruger Mark IV Replica to match the real steal one more closely. Shot placement out of the box was close to the bullseye, it just needed to move up a bit and a tad to the right but once the sights are adjustable for windage and elevation this is easily fixed with a few turns of the sighting screws. If you are a Ruger 22LR owner than I would suggest you buy one of these Umarex Ruger Mark IV Break Barrel .177 Cal Pellet Pistols and shoot for even less cost per shot and in more locations since this Air Pistol is super quiet and most makeshift backstops will work with it just fine.
Type: Airsoft Pistol. Distributer: Action Army. Model:Action Army AAP-01. Materials: Metal and polymer build. Weight: 1.43 pounds (648 grams). Barrel: 5/9.25 inches. Total Length: 9 inches. Propulsion: Gas Blowback. Action: SAO. Ammunition Type: .6mm Airsoft BB’s Ammunition Capacity: 22 rounds. FPS: 360.
Trigger Pull: The trigger pull on the Action Army AAP-01 GBB Airsoft Pistol is fairly light, it is a single action only trigger meaning you will need to pull the bolt back to engage the trigger and load an Airsoft BB into the breach. I noticed there is about a 1/4 inch of take-up with a firm breakpoint and easy trigger release. You will also notice there is a trigger safety on the trigger but it does not get in the way at all.
Accuracy: I have not had the chance to really test out this Airsoft Pistol but will be doing so next week when I make my Field Test Shooting Video for the Action Army AAP-01 GBB Airsoft Pistol. I did load up a magazine with propane and do a mag dump in full auto and managed to get though it all but I did pretty much use up all the Gas shooting in full auto. I am sure when in semi auto the gas will go a lot further. I look forward to seeing how it performs in the Filed test in term of accuracy and velocity.
Build Quality: The Action Army AAP-01 GBB Airsoft Pistolhas a good overall build quality and fit and finish. There is a lot of plastic on the outside but good use of metal internally in the bolt, barrel and magazine giving it decent weight but not making it too heavy.
Realism: The Action Army AAP-01 GBB Airsoft Pistol is not an actual Replica specifically of any one particular real steel gun in production, that said it does resemble the Ruger series of 22LR pistols in design and how the bolt functions. You will finds lots of working parts that function as you would expect to them if this was a powder burner. Like the bolt, slide catch, magazine release, safety, trigger safety and full size drop put metal magazine. You can even field strip this gun easily.
Pros:
Full Blowback operation.
Full size dropout G-series metal magazine .
Fiber optic front and back sights.
Can mount rails on top and bottom (not included).
Comes with short and long barrels.
Has a 14mm threaded barrel which can be used to add a mock suppressor to hide the barrel extension.
Working trigger safety and added cross bolt safety.
Mostly everything is ambidextrous.
Can be used in semi auto or full auto mode with the flick of a switch hidden under the bolt.
Overall a nice looking custom Airsoft Pistol!
Cons:
Rear sight not adjustable.
May be hard to find a holster for it.
Seems to eat a lot of gas especially in full auto mode.
Comments: What I really like about the Action Army AAP-01 GBB Airsoft Pistol is that it is rather unique looking, it looks nothing like a Glock, or 1911, or a Beretta or Sig so if you want something that stands out from the crowd then this may be it. I also like the ability to shoot in semi auto or full auto with the click of a switch and since it uses standard G-series magazines you should be able to easily find higher capacity extended mags that hold more gas and more Airsoft BB’s which you will for sure need if you plan to be shooting this one in full auto often.
My Vimeo Table Top Review Videos for the Action Army AAP-01 GBB Airsoft Pistol:
Type: Pellet Pistol. Distributer:Umarex. Model:Ruger Mark IV. Materials: Metal and polymer build. Weight: 1.56 pounds (708 grams). Barrel: 5.3 inches (135mm). Total Length: 11 inches (279mm). Propulsion: Spring Piston. Action: SAO Break Barrel. Ammunition Type: .177 caliber pellets. Ammunition Capacity: 1 round. FPS: 320+.
Trigger Pull: The trigger pull on the Ruger Mark IV Break Barrel .177 Cal Pellet Pistol is not too bad, I feel it is a around 6-7 pounds or so without measuring. In comparison to a real steel 22LR semi auto SAO trigger pistol, the trigger is much heavier but most of these 22LR pistols of this nature have what I would consider to be near perfect triggers. Over time once you get use to the pressure and release point accuracy with this pistol it is for sure possible.
Accuracy: I have not had the chance to really test fire this pellet pistol but will be doing so next week when I make my Field Test Shooting Video for the Umarex Ruger Mark IV Break Barrel .177 Cal Pellet Pistol. If it is anything like the Umarex Buck Mark URX which I imagine it will be, then I am expecting to get some good accuracy as the URX was able to get a nice under 1 inch shot grouping when I tested it a few years back. Velocity I am expecting to be up and over 300 fps even using lead pellets, I am hoping it will be in the mid 300’s
Build Quality: The Umarex Ruger Mark IV Break Barrel .177 Cal Pellet Pistolis a low cost target plinker that also doubles as a licensed Replica for that coolness factor so you won’t get an all metal super top quality build here. That said metal and plastics are well used and for sure details in the fit and finish have been improved over the Buck Mark URX version where I found the barrel felt a bit sloppy and the trigger was plastic. The Umarex Ruger Mark IV Break Barrel .177 Cal Pellet Pistol has a much tighter barrel fit when closed and the trigger is now metal! Maybe Umarex watched my video back in the day and took some notes?
Realism: The Umarex Ruger Mark IV Break Barrel .177 Cal Pellet Pistol most resembles the Mark IV Hunter edition and is pretty much bang on in terms of being a replica other than the tell tail hinge just under the barrel required for a spring piston design, there really is no way to get around this so I’m not going to criticize this minor difference. The real steel version is almost 3 pounds and so the pellet shooting version is a bit under weight so it would have been to have had more metal perhaps in the barrel and lower frame. Again since the pellet shooting version is a springer you will not have any working bolts or slide catches or a built in magazine.
Pros:
It's a decent Ruger Mark IV Replica!
Feels well built overall.
Expect it to have really good accuracy like the Umarex Browning Buck Mark URX since they share similar mechanical design.
Barrel locks into place much better than the Umarex Browning Buck Mark URX did.
Fully adjustable rear sight with fiber optic front sight.
Auto locking safety, just don’t forget to unlock before each shot
Actual metal trigger in this version.
Nice and compact, not too heavy.
Full Ruger licensed via Umarex.
Fairly low price tag.
Cons:
No built in rail for a sight system like the Umarex Browning Buck Mark URX but this is tru for the Hunter version.
Trigger pull could be lighter to match the real steel version.
A bit more metal would have been nice to get the weigth up closer to the real steel version.
Comments: I remember the Umarex Buck Mark URX being a super fun pellet pistol to shoot even though it is only a single shot airgun. Sometimes just getting back to the basics and taking your time to really place your shots and see how accurate you can be is more fun than spraying BB’s and pellets rapid fire and hoping you hit something. The Umarex Ruger Mark IV Break Barrel .177 Cal Pellet Pistol is inexpensive to buy and inexpensive to shoot, no CO2, just a tin of your favorite pellets and you will get hours of fun for it while honing your shooting skills. And at the end of the day the Umarex Ruger Mark IV Break Barrel .177 Cal Pellet Pistol is not a bad Replica Airgun if you are a collector of shot guns.
My Vimeo Table Top Review Videos for the Umarex Ruger Mark IV Break Barrel .177 Cal Pellet Pistol:
In this Preview Unboxing Vimeo Video I take a look at five very different products! A Spring Piston .177 Caliber Pellet Pistol, an Airsoft GBB Pistol, a Compact Crossbow, a full auto CO2 Blowback BB Pistol and a PPC .22 Caliber Pellet Rifle.
First up is the Umarex Ruger Mark IV Spring Piston Pellet Pistol which is a single shot replica pellet pistol that shoots .177 caliber pellets at up to 320 fps using a spring piston break barrel system. The Umarex Ruger Mark IV Spring Piston Pellet Pistol is a target plinker with fully adjustable fiber optic sights and should be a lot of fun to shoot!
Next I take a look at a Gas Blowback Airsoft Pistol from Action Army that closely resembles the Ruger Mark IV pistol with perhaps a more compact look. The Action Army AAP-01 GBB Airsoft Pistol is full blowback a full size drop out magazine and fiber optic sights. It also come with a threaded barrel and barrel extension for adding a longer barrel and much suppressor.
Next on my list of new items is the Bear X Desire XL Crossbow which is a 2.2 pound compact bolt shooting crossbow that sports a rail system with included adjustable iron sights that also allow for a red dot if you want to really customize it. The Bear X Desire XL Crossbow has a 60 pound draw and shoots arrows/bolts at up to 175 fps.
Another AR BB Rifle/Pistol from Crosman is the Crosman A4-P Full Auto CO2 BB Pistol which is essentially a pistol version of the AR Platform. If you like the Crosman DPMS SBR, R1, PDW then you will probably also like the Crosman AP-4. Like the others it uses dual CO2’s and shoots 4.5mm Steel BB;s in semi or full auto at 1400 rounds per minute until the 25 round magazine is empty.
Last included in this preview video is the Air Venturi Avenger Regulated PCP Pellet Rifle. I’m a bit uncertain about this one as I am pretty sure it is the non detuned PAL version that requires a firearms license here in Canada as it shoots at full velocity (.22 caliber pellet at 950 fps). If that’s the case then it will not be available in our Canada Replica Airguns Store but may be available in the US Replica Airguns Store. If it is the detuned version or a detuned version becomes available in Canada then I imagine we will at some point have it in the Canada replica Airguns Store. That said the Air Venturi Avenger Regulated PCP Pellet Rifle uses compressed air and shoots either .177. .22 or .25 caliber pellets using a latch system and rotary magazine.
Back in 2017 I made “Which Beretta Airgun is the Best” Video and showed off some 4.5mm Steel BB and .177 Caliber Pellet versions of my favorite Beretta 92 - M9 style Air Pistols. There have been some changes since then most noticeably the addition to Airsoft versions so I thought I would update this video with more current Beretta Airguns along with of course some of the same ones form my last video.
Because I show off 4.5mm Steel BB, .177 Caliber Pellet and 6mm Plastic Airsoft versions I decided to pick my favorites form each category. Watch my Vimeo Review Comparison Video so checkout these Air Pistols and see which ones are my favorites…
.177 Caliber Pellet Beretta 92 -M9 CO2 Air Pistols
In this Table Top Comparison Vimeo Video I take a look at the full line of Sig Sauer distributed Replica CO2 Blowback Airguns and pick out my favorite 4.5mm Steel BB and .177 Caliber Pellet shooters out of the bunch. You will have to watch the video to see what my two picks are!
In this Vimeo Comparison Review Video I take a look at a selection of Glock CO2 4.5mm Steel BB Pistols, four from Umarex and 1 from KWC. I go over some of the similarities and differences of each of them and ultimately decide which one is my personal favorite out of the bunch based on what I generally look for in an Airgun.
Type: Airsoft AEG. Distributer:ASG. Model: CZ Scorpion EVO 3 A1. Materials: Metal and polymer build. Weight: 5.3 pounds (2400 grams). Barrel: 208mm (8.2 inches) Total Length: 425-623mm (16.7-24.5 inches). Propulsion: AEG. Action: Semi, burst, full auto. Ammunition Type: .6mm plastic Airsoft BB’s. Ammunition Capacity: 75 rounds. FPS: 395.
Trigger Pull: The trigger pull on the ASG CZ Scorpion EVO 3 A1 6mm AEG Airsoft Gun is essentially just an on off electric switch controlled by the ECU. There is very little trigger resistance and the take up is very short allowing for quick semi auto shooting but if you like you can easily select three round burst or full auto shooting for more intense situations.
Accuracy: I have not performed my Field Test Shooting Video for the ASG CZ Scorpion EVO 3 A1 6mm AEG Airsoft Gun but plan to get to that video next week. I really have no idea what to expect at this point since i have not even loaded up a magazine and taken it for a spin yet. I am sure I will not be dissapoitned as this is a very high quality Airsoft Gun with great internals.
Build Quality: I remember at SHOT Show back when ASG introduced the ASG CZ Scorpion EVO 3 A1 6mm AEG Airsoft Gun, I was told indirectly that the construction was nearly identical to the real steel CZ Scorpion EVO at least cosmetically as all the internal parts will be specificities to Airsoft. That said this is a very high quality build with the material being for the most part the same as the original with Nylon Fiber PA6 Polymer reenforced plastics and even some CNC machined metal parts as in the outer barrel, flash hidden, barrel nut and even the gear box.
Realism: The ASG CZ Scorpion EVO 3 A1 6mm AEG Airsoft Gun is a bang on replica in terms of emulating the real steel CZ Scorpion EVO and has our weight and feel including a blot catch that locks back when out of ammo and most working components being ambidextrous.
Pros:
Build quality is almost exactly like the real steel version, super high quality materials.
Three shooting modes: semi auto, burst mode and full auto.
Decent mid capacity 75 round magazine with auto empty detection which locks the bolt catch.
Quad rail for lots of add on accessories.
Folding and adjustable stock that can also be removed.
Adjustable and removable iron sights with fiber optic up front and peep in the back.
Working charging handle for easy access to hop-up
Working bolt catch.
High quality electronic and gear box.
Ambidextrous controls for the most part.
Scorpion licensed through ASG.
Orange tip is fairly discreet.
Cons:
Battery compartment is small and hard for quick battery replacement, I recommend using an external setup if possible.
Price point is on the higher side but you get what you pay for.
Comments: On paper and just by looking over and inspecting the ASG CZ Scorpion EVO 3 A1 6mm AEG Airsoft Gun specs out and I am sure I will be pleased when I test it out in the Replica Airguns Indoor Shooting Range. That said this hasn’t happened yet so I will leave my final thumbs up until then. I do wish we had them in stock at the time of this video but there are a lot of other great ASG products in our store and of course many more brands of AEG Airsoft Guns. Hopefully we can get something like this in shortly for everyone so keep checking with us.
My Vimeo Table Top Review Videos for the ASG CZ Scorpion EVO 3 A1 6mm AEG Airsoft Gun:
In this Field Test Shooting Video I put the Webley Valuemax 22 Caliber Spring Piston Break Barrel Rifle through my standard Replica Airguns Indoor Field Test protocol by first testing out the velocity and placing 5 rounds through my Chronograph to see what the actual real world fps is using 14.3 grain lead pellets. I then setup a fresh paper target 30 feet downrange and place 10 pellets into it to see what type of grouping I can get. If you have not already watched my Table Top Video for this Break Barrel Spring Piston Pellet Rifle then make sure to do so for more details, specifications and close up video.
Starting off with my real world velocity test for the Webley Valuemax 22 Caliber Spring Piston Break Barrel Rifle, I went with 14.3 grain lead pellets which are I would say on the heavier side. Even so I managed to hit 478 fps which produced a nice 7.26 foot pounds of energy which by the way is almost 10 Joules! If you are wondering about Canadian legalities, as long as I do not go over 500 fps AND go over 4.2 foot pounds (both thresholds must be exceeded), then this Airgun is considered a non-regulated firearm and does not require a firearms license.
Moving on to the accuracy portion of my Indoor Field Test in the Replica Airguns Sea Can. As always I placed a brand new paper target 30 feet downrange and proceeded to shoot ten 14.3 grain lead pellets from a rested and seated shooting position to allow for best possible results with as little human error but I am imperfect so some human error is always present. I was using the open fiver optic sights on the Webley Valuemax 22 Caliber Spring Piston Break Barrel Rifle rather than a scope even thought there is a dovetail rail with included scope stop. To be honest I was expecting a better grouping, something close to half an inch but on this day with this ammo choice I was closer to 1.5 to even 2 inches. I did see several pellets land in a tighter sub group but some came out of this group enlarging the grouping. I would like to try a different pellet choice to see if I can do better as I believe this rifle has way more potential.
In terms of power the Webley Valuemax 22 Caliber Spring Piston Break Barrel Pellet Rifle is about has high as you can go before it becomes a regulated firearm here in Canada so no complaints in that department. Again I was disappointed in the accuracy but I honestly believe a different pellet choice could fix that problem as I have seen often with other Pellet Rifles. Once the right pellet choice is made and granted a more consistent and tighter grouping is achieved, this Spring Piston Pellet Rifle could make a decent small pest control airgun!
Type: Pellet Rifle. Distributer:Webley & Scott. Model:Valuemax. Materials: Metal and polymer build. Weight: 6.4 pounds (2900 grams). Barrel: 17.7 inches (450mm), rifled. Total Length: 43 inches (1092mm) Propulsion: Spring Piston Action: Break Barrel. Ammunition Type: .22 Caliber Pellets. Ammunition Capacity: Single Shot. FPS: 499.
Trigger Pull: The trigger pull on the Webley Valuemax .22 Caliber Spring Piston Break Barrel Rifle is fairly nice There is a little bit of very light take up followed by a vert light release , the take up or travel length can be adjusted on this Air Rifle but that is the only trigger adjustment you can make and perhaps all that is needed.
Accuracy: I have not performed my Field Test Shooting Video for the Webley Valuemax .22 Caliber Spring Piston Break Barrel Rifle but I did get to take around 20 or so shots with it when I was trying to get it to diesel for me. It looks ot me like it is going to be nice and accurate as I was not even really going for accuracy and it seemed to already be grouping fairly tight. I was recoding fps using my Chronograph as I was trying to find out if by adding some oil to the spring piston chamber could get it to diesel which it never did for me, I was however to establish that the Webley Valuemax .22 Caliber Spring Piston Break Barrel Rifle shot right around 470-480 fps using 14.3 grain lead pellets which worked out to right around 7.32 foot pounds of energy. I will know a lot more when I do my official Field Test Shooting Video next week.
Build Quality: Webley Valuemax .22 Caliber Spring Piston Break Barrel Rifle is built to be a value priced Airgun hence the name (Valuemax), that said it is maid well enough with lots of metal and of course some plastic or in this case mostly nylon as the stock is a solid nylon piece. Other than the stock the plastic parts are found to be in the sights and trigger guard, everything else seems to be metal.
Realism: The Webley Valuemax .22 Caliber Spring Piston Break Barrel Rifle is not a replica or copy of any real steel gun in production but it does look like a traditional hunting rifle in basic shape so make sure to transport thank airgun as if it was a real gun. Either in a gun case or perhaps a blanket in your trunk and always obey any laws for gun position and transportation in your area.
Pros:
Inexpensive price tag for well made decent performer.
Initial test showed to have good accuracy and power! (more to come).
Fully adjustable sights with optical TRUGLO Fiber Optics.
Can add a magnified optical scope using the top built in dovetail rail.
Nylon fiber stock is durable and functional with the addition of a vented rubber buttplate.
Trigger feels decent and is also adjustable for travel length.
Rear thumb safety resets after each break of the barrel.
Nice light and short single action trigger.
Would be good for small pest control because of decent FPS and good accuracy.
Cons:
Included sights are mostly plastic.
The Valuemax version has a more basic less adjustable trigger.
Detuned down to under 500 fps for Canada import as non-regulated Firearm.
Comments: I am looking forward to performing my Indoor Field Test Shooting Video for the Webley Valuemax .22 Caliber Spring Piston Break Barrel Rifle to see what it can really do in terms of accuracy so stay posted for that video next week. Overall if you are lucky enough to already have one or can get your hands on one since this rifle is discontinued in some area, I think this is a great Break Piston Air Rifle especially if you live in Canada and want the most bang for your buck. I am not only talking about cost verses features, I also mean power and energy since the Webley Valuemax .22 Caliber Spring Piston Break Barrel Rifle is a .22 caliber Air Rifle that can shoot really close to 500 fps with a nice heavy grain lead pellet achieving decent energy levels reasonable enough for small pest control. The Webley Valuemax .22 Caliber Spring Piston Break Barrel Rifle is not feature less, it does include a reseting safety, anti bear trap system, dove tail mounts with an included scope stop, fiver optic adjustable sights and a vert ergonomic textured nylon stock. All in all great value for what you pay!
My Vimeo Videos for the Webley Valuemax .22 Caliber Spring Piston Break Barrel Rifle:
In this Field Test Shooting Video I put the ASG Steyr Arms Scout Bolt Action Spring Airsoft Rifle through the regular Replica Airguns Indoor Field Test by first testing out the velocity and placing several rounds through my Chronograph to see what the actual fps is using both .20 gram and .40 gram Airsoft BB’s. Then I setup a fresh paper target 30 feet downrange and place 10 rounds into it to see how tight of a grouping I can get. If you have not already watched my Table Top Video for this Sniper Airsoft Riffle, then make sure to do so for more details, specifications and close up video.
Starting off with my real world velocity test for the ASG Steyr Arms Scout Bolt Action Spring Airsoft Rifle I decided to use both .20 and .40 gram Airsoft BB’s to see what a difference of double the weigth form the claimed for would actually be since for the most art this Airsoft Sniper Rifle is really meant to be using heavier Airsoft BB’ closer to the .40 gram weight. I was kind of expecting the heavier .40 gram BB’s to shoot almost half as fast since they where double the weight bu this was not the case! I shot 5 rounds with each weight Airsoft BB and with the .20 gram I averaged 479 which was actually faster than claimed, When I switched up to the .40 gram Airsoft BB’s I was surprised to get an average of 373 so only around 100 fps slower!
Moving on to the accuracy portion of my Indoor Field Test here in the Replica Airguns Sea Can, as always I placed a fresh paper target 30 feet downrange and proceeded to shoot 10 .40 gram Airsoft rounds into it from a rested and seated shooting position to allow for best possible results with as little human error added in. I was using a 4x optical scope since the ASG Steyr Arms Scout Bolt Action Spring Airsoft Rifle has a the added rail on top just fo this purpose and I would imaging most people are going to want to add a magnified scope to this Airsoft Sniper Rifle rather than use the built in pop iron sights that by the way are not adjustable. I know 30 feet is not the range one would be shooting this rifle at but it’s all I have for an indoor shooting range and it will give us an idea of what we can expect shooting further out… as in a nice tight group at 30 feet is going to mean better accuracy than a spread out grouping art 30 feet. I will say the ASG Steyr Arms Scout Bolt Action Spring Airsoft Rifle probably got one of the best groupings for an Airsoft Rifle that I have tested at 30 feet placing all 10 rounds within about an inch to an inch an a half.
I would like to take this Airsoft Sniper Rifle outside and see what it can do at much further out ranges again using nice and heavy Airsoft BB’s when it gets a bit warmer and stops raining so much :) But for now my Indoor Field Test performed about as good of a result as I can expect. The ASG Steyr Arms Scout Bolt Action Spring Airsoft Rifle is a really well made which paid off in two it performed for me. I don’t really see any need to upgrade this Airsoft Sniper Rifle other than adding an optical scope and perhaps investing in some high quality Airsoft Ammo.
Type: Airsoft Rifle. Distributer:ASG. Model:Steyr Arms Scout. Materials: Metal and polymer build. Weight: 6.5 pounds (2950 grams). Barrel: 14.5 inches (368mm), non-rifled. Total Length: 39.5 inches (1000mm) Propulsion: Spring Piston Action: Bolt action repeater. Ammunition Type: .6mm plastic Airsoft BB’s. Ammunition Capacity: 32 round magazine. FPS: 443. Type: Black and Grey versions.
Trigger Pull: The trigger pull on the ASG Steyr Arms Scout Bolt Action Spring Airsoft Rifle is short light and crisp. Working the bolt precooks the trigger for single action only shooting allowing for just the release of the hammer. There is very little take up and no creep at all, just a nice light and predictable trigger pull.
Accuracy: I have not performed my Field Test Shooting Video for the ASG Steyr Arms Scout Bolt Action Spring Airsoft Rifle so stay posted for that. ASG claims around 4430 fps velocity with the preinstalled M140 spring, you can upgrade the spring all the way up to an M190 spring for even higher potential fps. In terms of accuracy I am also expecting good results so check back next week for my Indoor Field Test Shooting Video for the ASG Steyr Arms Scout Bolt Action Spring Airsoft Rifle.
Build Quality: The ASG Steyr Arms Scout Bolt Action Spring Airsoft Rifle is well built with lots of high quality component not only inside but also internally. You will find a metal barrel and receiver along with metal bolt, trigger and rear sight, the front sight is however plastic. I donate really thin k you will be using the pop sights all that much as they are not adjustable and this gun really begs for a nice optical scope. The nylon polymer stock has micro-texturing to help with the grip in all weather conditions.
Realism: The ASG Steyr Arms Scout Bolt Action Spring Airsoft Rifle is based on the real steel 7.62 NATO Steyr Scout and even incorporates the integrated folding bipod legs like the original. For the most part they look identical but you will find the actual magazine on the Airsoft version is placed further up the stock to allow for the feeding of the Airsoft BB’s which does make the actual inner barrel shorter by about 4-5 inches.
Pros:
Nylon Polymer stock with micro-texturing.
Railed metal receiver with laser-etched Steyr trademarks.
Integrated folding bipod legs on left and right sides of the stock.
Flip-up backup front and rear sights.
Accessory slot on bottom of stock for mounting of optional bipod rail.
Millet QD sling loop attachment points.
Front dummy magazine.
Rear dummy magazine with storage for a spare magazine.
Removable stock spacer pads for length-of-pull adjustment.
90 degree trigger with steel sear.
90 degree aluminum piston with dual glide rings and steel base.
Silent Air Brake piston head.
Silent cylinder head with shock-absorbing padding.
9mm stainless steel ball bearing spring guide.
Bore-up steel cylinder with 12.5% more air volume than stock cylinders.
Hop-up unit with both side-lever adjustment and TDC screw adjustment options.
Steel CNC-machined hop-up arm.
03mm tight-bore inner barrel.
60 degree Modify Predator enhanced hop-up bucking preinstalled (50 and 70 degree buckings available separately).
Compatible with VSR-spec inner barrels.
450 FPS with pre-installed M140 spring.
Can take up to a M190 spring with no upgrades needed.
Cons:
32-round magazine.
Recommended ammo: 0.36g BBs and above, 0.4g optimal.
Comments: I am looking forward to performing my Indoor Field Test Shooting Video for the ASG Steyr Arms Scout Bolt Action Spring Airsoft Rifle. I won’t be able to test it out perhaps as far range as I would like to since I will be shooting it in the Replica Airguns Indoor Shooting range which allows me to test at 30 feet. That should give me a good overall idea on at least what it may be capable of since if we can get a tight group at 30 feet we should also be able to get a tight group at longer ranges with proper hop-up and heavier BB selection. I do plan on placing a scope on the ASG Steyr Arms Scout Bolt Action Spring Airsoft Rifle to give it the best possible chance of performing at it’s best and really hope to see a good result from it.
My Vimeo Videos for the ASG Steyr Arms Scout Bolt Action Spring Airsoft Rifle:
In this Field Test Shooting Video I put the ASG Action Army T-11 Spring Powered Bolt Action Airsoft Gun through it’s paces by first testing out the velocity placing several rounds through my Chronograph, and then I setup a paper target downrange and place 10 rounds into it to see how tight of a grouping I can get. If you have not already watched my Table Top Video for this Airsoft Sniper Pistol/Rifle then make sure to do so for more details, specifications and close up video.
Starting off with my real world velocity test for the ASG Action Army T-11 Spring Powered Bolt Action Airsoft Gun, I decided to use .28 gram Airsoft BB’s for this entire Field test Shooting video so I was expecting to get somewhere between 20-25% slower fps velocity as compared to the standard tested .20 gram Airsoft BB’s. After placing around 6 shots through my Chronograph I averaged 328 fps which ended up being 18% slower than the claimed 400 fps made by ASG. I would image if I had used .20 gram Airsoft BB’s I may have even exceeded 400 fps.
Moving on to the accuracy portion of my Indoor Field Test here in the Replica Airguns Sea Can, as always I placed a fresh paper target 30 feet downrange and proceeded to shoot 10 rounds into it from a rested and seated shooting position to allow for best possible results with as little human factor added in. I was using a 4x optical scope since the ASG Action Army T-11 Spring Powered Bolt Action Airsoft Gun does not come with any type of sighting system included so I did have to sight it in initially. I did manage to get a nice 1.5 inch grouping fairly close to the bullseye but I did notice that if I angled the barrel down a bit, BB’s would roll out of the barrel which made me wonder if the hop-up was set high enough to engage a BB.
So I did my second test with the hop-up set in the middle range and this time BB’s did not fall out of the barrel when angled down. After the hop-up adjustment I did notice I was shooting a bit higher which is expected with more hop-up adjustment so if you are experiencing BB’s falling out of the barrel then make sure to adjust your hop-up a bit tighter.
All in all the ASG Action Army T-11 Spring Powered Bolt Action Airsoft Gun performed very well for me especially once I got the hop-up figured out. And I do think it makes for a really nice compact Sniper Rifle if bulkiness is a factor for you, if not then checkout the Rifle version of this gun with the more traditional but-stock and longer barrel.
