My main goal in this Shooting Performance Test was to see how the ANT Advanced Novelty Tech CO2 HPAConversion Kit performed side by side with a standard 12 gram CO2. Keep in mind that you can also switch over at any time to a regular 12 gram CO2 even after installing the ANT adaptor system in the gun or magazine.
My choice of Airgun for this test was the KWC - Cybergun Mini UZIConverted to Full Auto. I chose this Blowback 4.5mm CO2 BB Gun because it uses a lot of CO2 with each shot and when shooting in full auto it literally eats CO2. I knew this airguns would really put the ANT Advanced Novelty Tech CO2 HPA Conversion Kit to the test.
My first performance test was to comparing both systems using a Chronograph so I could see how the fps velocity slowed down because of the CO2 cool down effect. The 12 gram CO2 did pretty well emptying a full 25 round magazine but keep in mind I was shooting in semi auto only for the sake of using a Chronograph. I did notice a drop in velocity from a high of over 300 fps to a low of around 260. When I switched over to the Bulk CO2 ANT System and performed the same test the fps started out a bit lower but stayed pretty much about the same with a few ups and downs. The initial lower fps may have been a result of using separate magazines for each test since the valves in each magazine are most likely tuned a bit differently to let out more or less CO2 with each shot.
My second and most impressive test was to empty a full 25 round magazine in full auto mode! Again a started out using the standard 12 gram CO2 and to make this a real world test, I did not replace the 12 gram CO2 form the previous test. I figured 50 shots was a realist amount of shots to get from a single 12 gram CO2 and after all I was only shooting in semi auto which uses a lot less CO2 then shooting in full auto.
My KWC Blowback Mini UZI rocked pretty good using the 12 gram CO2 until it hit about a third the way through the magazine and then it stated to slow down and pretty much stop dead in its tracks with about 5-6 rounds still left in the magazine. The CO2 was all gone and I was left a bit unsatisfied :(
Without any significant break time to let my KWC Mini UZI warm up again, I switched over to the ANT Advanced Novelty Tech CO2 HPA Conversion Kit magazine and unloaded the full magazine in no time with no cycle rate slow down at all, even after the magazine was deprived of Steel BB's I kept squeezing the trigger and letting the blowback hammer my shoulder for several more satisfying bursts. Now that is what you expect from a full auto Blowback BB Machine gun!
In conclusion, when shooting in semi auto you will see better fps consistency using the ANT Advanced Novelty Tech CO2 HPA Conversion Kit but where this system really shines at least for me is I can shoot as fast as as long as I want and it will feel same as the very first shoot I take even when using a full auto system. No more switching out 12 gram CO2 every few magazines, just speed load some more BB's in and your good to go.
I was sent a really cool new product form a company called ANT (Advanced Novelty Tech). Their CO2/HPA Converter allows you to hook up either a large CO2 tank or High Pressure Air system using standard Paintball hose system.
What's kind of neat with the Advanced Novelty Tech CO2 HPA Conversion Kit, is that you can still interchange your 12 gram CO2 if you want to even after modifying your gun to use Bulk CO2 or HPA!
The ANT Advanced Novelty Tech CO2 HPA Conversion Kit works with well over 100 BB, Pellet and Airsoft guns most of which would be Pistols but some rifles are included in this list.
The main advantages over using standard 12 gram CO2 cartridges would be a significant lower cost for CO2, along with less fps velocity fall off, so better performance overall.
Stay posted as I will be making a field test performance test using the ANT Advanced Novelty Tech CO2 HPA Conversion Kit with my KWC Mini UZI Full Auto BB Machine gun :)
A few years back the Umarex SA177 disappeared off the face of the earth, well not really, it simply juts stopped being made and fairly quickly retailers ran out of stock... As with anything that people want but can not get any more, the demand went up and all of a sudden everyone seemed to want to get their hand on an Umarex SA177 Blowback BB Pistol.
You might ask why Umarex stopped making what at the time was a fairly popular CO2 BB Pistol? Well if you know anything about Glock, they do not like it all that much when a company makes a product that they feel infringes upon their intellectual properties and copy writes. Did the SA177 look like a Glock, well sure it had some similarities and perhaps Glock felt it was a bit too similar and so may have kindly asked Umarex to stop making it? At least that's what I think happened :)
So that brings us to now. And a new gun on the market called the Umarex 9XP that in many ways is a lot like the SA177 but with a slightly new skin on it, one that differentiates itself a bit more from the traditional Glock look. Sure the Umarex 9XP Blowback BB Pistol has a some Glock looking properties but it am guessing it has enough subtle changes to make the lawyers over at Glock HQ happy enough to allow Umarex to again sell an airgun very similar to the SA177.
Internally and mechanically as far as I can tell the Umarex SA177 and Umarex 9XP are the same and so they should both perform very similarly too each other and with pretty much all the same specifications. Even the magazines seem to be interchangeable! The trigger and trigger pull look to be identical and even the slide catch release are modeled after each other. Again, the only difference are some minor cosmetic changes to the metal slide and polymer frame.
So if you have been looking to get your hands on an SA177, well the next best or perhaps even better airgun is now available in the new Umarex 9XP! And the price is all right too!
Trigger Pull: Trigger pull on the Umarex Colt Single Action Army Shell Loading BB Revolvers is the best I have ever come across in an airgun. Being that the Umarex Single Action Army Revolvers are single action only, most of the work is done while you pre-cock the hammer. The trigger pull is under 2 pounds and has virtually no take up with a crisp release.
Accuracy: I tested both 4.5mm steel BB's and 4.7mm Lead ball BB's in the Umarex Colt Single Action Army Shell Loading BB Revolver. With the Steel 4.5mm BB's I shot just under a 2 inch 6 shot grouping when shooting from a 30 foot distance using a semi rested position (Sand bag up front, standing in the back). The shots where pretty well center hitting the paper target just a little bit high, they did seem to stray a little more left and right rather then up and down. When I switch ammo to the 4.7mm Lead BB's I got a similar 2 inch grouping but they hit the target a bit lower and tended to shoot tighter from side to side with more variation up and down, perhaps because the lead BB's did not seem to shoot at a vary consistent velocity. My Chronograph testing for the Steel BB's was right around 400 fps while the Lead BB's being heavier shot a bit slower at just under 300 fps.
Build Quality: The Umarex Colt Single Action Army Shell Loading BB Revolvers have a mostly all metal construction other than the plastic grips and any seals. The fit and finish is excellent with a great overall weight in the hand. Whether you get the Nickel or Blued version. The mechanical action of the hammer and trigger feels just like it would on a real single action army revolver.
Realism: In terms of replicating a real steel Colt Single Action Army Revolver, Umarex has done a really great job with their CO2 BB firing version. It's really hard to tell one from the other except for the smaller shells and the discreet safety switch located under the frame. Even the barrel is nicely recessed and has some fake rifling twists in it. The CO2 is well hidden with the Allen key built into the handle so no ugly screw tab hanging down.
Looks amazing and is a very accurate replica of the real steel old west version.
Recessed barrel with fake rifling.
Great weight and feel in the hand.
Shell loading design that loads from the back so no need to remove shells if you wish not to.
Hammer and trigger action is about perfect, no take-up, very crisp and super light.
Finish on both the Nickel and Blued version is very nice.
Very well concealed CO2 with built in Allen key.
Discreet safety location.
Cons:
In your face warning instruction on the right side of the barrel are a shame.
Real steel version would shoot .45 caliber bullets, dummy shells are actual closer to a .38.
Seems really quiet to shoot, would like to see a louder more powerful version!
Comments:
All I can say is we finally got our Airgun 1857 Colt Single Action Army Revolver! I have been asking the big airgun companies for this for a while and I knew it would be very popular once made available. As it turns out, not only do the "Americans" want one, but so do many folks overseas! I am really glad that time and effort was put into this first version and we got such a great product that looks amazing and shoots just as good as it looks. For anyone who is interested in owning the classic cowboy six shooter, you have to make sure to get one of these super realistic Single Action Historic Revolves!
My Vimeo Table Top Review for the Umarex Colt Single Action Army CO2 BB Revolver :
Some more new guns I will be checking out, well one is just a different finish of the Umarex Colt SAA Revolver but for sure worth taking a look at in this Preview Video.
All the guns in the Vimeo Preview Video and CO2 4.5mm BB Pistols, three are styled after revolvers and one is based on a semi auto modern pistol.
Starting with the revolvers I show off the absolutely gorgeous blued finish on the Umarex Colt Single Action Army BB Revolver and it all I can say is it really needs to be seen in person to fully appreciate how great it looks. I was not expecting the blued version to look nicer than the Nickel version but in my opinion it is my favorite of the two. And that's not to say the Nickel version is not a great looking pistol in it's own right.
I've been waiting a while to see firsthand the Webley & Scott MK6 CO2 BB Revolver and it finally came this week. Another really well built and designed classic Revolver to add to the list of shell loading CO2 BB Revolvers. I was really impressed with the trigger and hammer action, both single and double action feel super smooth and the position of the hammer makes for really easy draw for single action shooting. The 2.4 pound all metal weight give the Webley & Scott MKVI great balance and realism, while the top-break design makes for super easy loading.
Not to be mistaken with the Full Metal Shell Loading Umarex Colt Python 357, I take a look at the more affordable Umarex Polymer Colt Python 357 that fits the bill nicely when looking for a BB Revolver with a nice hammer and trigger, fully adjustable sights, and higher than average capacity magazines than your standard revolver.
Last but not least I look at another fairly affordable CO2 BB Pistol, the Umarex HK45. It's a pretty basic CO2 BB pistol but looks really good and has decent weight with its metal slide. The HK45 features white dot sights, a Picatinny rail, an all metal drop out stick magazine and full Heckler and Koch licensing.
Part 2 of my two part Field Test Shooting Video Review, this one focuses on the accuracy or target portion using my Umarex Colt Single Action Army Shell Loading BB Revolver. As per usual I set my self up 30 feet from my paper targets using a semi rested position (Standing in the back, while resting the gun on a sand bag up front). I normally take 10 shots and see what kind of a grouping I can get but with a six shooter that requires some reloading so we will base this testing on six shots.
Like part 1 in my Chronograph or velocity Field Test, I use a variety of ammo, starting off with 4.5mm Steel BB's and then switching to some 4.7mm Lead BB's for the second group of 6 shots from the Umarex Colt Single Action Army Revolver. I decided not to try the Dan Wesson Dummy Shells since they proved to be not so reliable during my Chronograph testing.
At the end of the Video I have some fun with my KWC / Cybergun Government 1911 just to see how it compares to a fixed barrel revolver.
Make sure to watch my below YouTube Review Video to see my full shooting accuracy result, I can say both the steel and lead BB's shot from the Umarex Colt Single Action Historic BB Revolver shot similar under 2 inch groupings with the lead BB's dropping a bit on the target with their slower velocity.
I decided to split this Field Test Shooting Review of the Umarex Colt Single Action Army into two parts since i wanted to do multiple tests with multiple types of ammo and dummy shells. at the end of the video I also throw in my Cybergun / KWC 1911 Blowback BB Pistol just for fun since both of these pistols where used in the US Military.
I start off by testing out the Umarex Colt Single Action Shell Loading BB Revolver shooting 6 rounds through my Chronograph using the included Umarex Dummy Shells with steel 5.1 grain 4.5mm BB's since this is what most people will experience. In my second test I switch up the ammo slightly and try out some much heavier Lead BB's that are a bit larger than 4.5mm (about 4.7mm) and weigh in at somewhere between 7-8 grains.
On my third test I go back to the standard 4.5mm Steel BB's but switch out the included Umarex dummy shells and replace them with some Dan Wesson Dummy Shells. Both shells are about the same length and width but with the included Umarex shells, you load the BB's into the back of the shell. With the Dan Wesson shells you load the BB into the front of the shell.
What do you do when you have some nice weather and a brand new Umarex Shell Loading Colt Single Action Historic CO2 BB Revolver that you are itching to try out! Well you go shoot it, that's what you do! So I thought I would setup a bunch of miscellaneous targets along with some cameras and record the fun so you all could join me :)
I did use steel BB's for the most part but I also gave some lead BB's I had lying around a try, the lead BB's are a bit larger in diameter so they fit fairly snug, I would not recommend using them on anything other than a brand new CO2 cartridge or they could get stuck in a shell or the barrel. The lead BB's are also much heavier than steel BB's so they do not go as fast but seemed to work pretty good for me. A great option if you are shooting at metal targets with your Umarex Colt Peacemaker!
I also discovered that one can simply load BB's directly into the back of each shell without having to actually take the shells out of the Umarex Colt Single Action Army Revolver, so if you only have 6 shells and want to keep the shooting moving along then just pop the BB's directly into the shells.
I finally got my hands on one of the Umarex Colt Single Action Historic Revolvers! Rather than making you wait for my full Table Top and Field Test Reviews I thought I would post a quick unboxing preview video. Of course my full Table Top and Field Test videos will follow...
In this unboxing preview video of the Umarex Colt Peacemaker Single Action Army Revolver I show you around the CO2 4.5mm BB Revolver Replica and even compare it to a few similar revolvers I have lying around.
The Umarex Shell Loading Colt Peacemaker is an amazing replica and simulates the old west cowboy Single Action Only Revolvers in almost every detail. I love the hammer action and the ratchet sound it makes as you draw it back. The Single Action Only Trigger is very light at under 2 pounds just as it should be.
This is my Official Field Test Shooting Review video for the Gletcher CLT B25 CO2 BB Shell Loading Revolver. This pistol is actually made by KWC and is the same base gun that Umarex uses in their Licensed Colt Python 357 6 inch barrel version.
In this Shooting video I performance various Field Tests on the Gletcher CLT B25 using my Chronograph to get a true live performance reading of the velocity in fps. I also shoot 6 rounds at a paper target positioned 30 feet from my semi-rested position (Sand bag up front and standing in the back).
Velocity wise, the Gletcher CLT B25 CO2 BB Revolver shot a little low while using standard 5.1 grain zinc coated steel BB's coming in with a 5 shot average of 280 fps. the claimed the fps from Gletcher is 100 m/s which works out to 328 fps so there is room for some improvement, perhaps on a warmer day I may see these numbers?
I then moved back to my 30 feet shooting position to test out the accuracy using paper target, the Gletcher CLT B25 CO2 BB Shell Loading Revolver produced n OK 6 shot grouping that was just over 2 inches in diameter. Not supper but also not too bad considering the short barrel and how tight the front and back sights are together. I'm pretty sure I can do a bit better as one of the shots did pull a bit out form the rest making the grouping larger than it could have been.
Overall, the Gletcher CLT B25 CO2 BB Revolver shot pretty has a nice feel to it when shooting, the trigger/hammer setup is nice in both single and double action, the grips and balance feels good and overall this is a very fun shell loading BB revolver to shoot.
This is my Official Field Test Shooting Review video for the Gletcher SW R25 CO2 Shell Loading Pellet Revolver. At this time we are out of stock, I am not sure exactly when we are going to have them back in stock.
In this Field Test Shooting video I test out the performance of the Gletcher SW R25 using my Chronograph to get an actual Feet Per Second velocity rating, I also shot 6 rounds at a paper target setup 30 feet away using a semi-rested position (Sand bag up front and standing in the back).
Velocity wise, the Gletcher SW R25 CO2 Pellet Revolver shot pretty hard considering I was using 7 grain lead pellets (as compared to 5.1 grain steel BB's) and this was the shortest barreled version at 2.5 inches. The Gletcher SW R25 averaged a 337 fps 6 shot velocity with its highest fps shot of 351.
I then stepped back 30 feet and shot at a paper target, the Gletcher SW R25 CO2 Shell Loading Pellet Revolver produced a nice tight 6 shot grouping that was really close to 1 inches in diameter. Considering how short the barrel is and how close together the front and back sight are to each other, this is not a bad result at all. I am sure the rifled barrel helped a lot here. I did shoot a bit high and to the left but this can easily be corrected by adjusting the rear sight for windage and elevation.
Overall, the Gletcher SW R25 CO2 Pellet Revolver shot pretty hard and with good accuracy for a shell loading pellet revolver. It will be interesting to see how well the 8 inch version of this Gletcher Shell Loading Pellet Revolver does when I test it out shortly?
In this Field Test Shooting video I test out the performance of the Gletcher Grach NBB using my Chronograph to get a real world Feet Per Second rating, I also take aim 30 feet back and shoot 10 rounds at a paper target using a semi-rested position (Sand bag up front and standing in the back).
In terms of velocity the Gletcher Grach NBB CO2 BB Pistol performed a little lower fps then I expected shooting just under 350 fps. It was about 15 degrees celsius on this day but I also kept the pistol indoors where it was nice and warm right up till shooting time. I used a brand new CO2 and my ammo of choice was RWS 5.1 grain zinc coated BB's.
Stepping back 30 feet and shooting at a paper target, the Gletcher Grach NBB CO2 BB Pistol produced a very tight 10 shot 1 inch grouping, not many BB's pistols have been able to get in that 1 inch grouping at least for me! The Gletcher Grach did shoot a little to the left and a bit low but not far off the bullseye. The sights are not adjustable so you will have to slightly adjust your aim point if you find yourself not exactly dead center.
I found the Gletcher Grach NBB to be extremely quite so if you are looking for a discrete backyard shooter then the Grach would be a good choice. I also found the trigger to be very good in both single and double action but when the BB mag is loaded to the max, the trigger first stage will be very heavy since the follower spring is holding the BB's in place and creating friction while a BB is loaded into the chamber. To fix this problems simple don;t load as many BB's in the magazine.
In this Field Test Shooting video I test out the performance of the ASG CZ 75 CO2 Blowback 4.5mm BB Pistol using my Chronograph to get a real world Feet Per Second rating, I also position myself 30 feet back and shoot 10 rounds at a paper target using a semi-rested shooting position (Sand bag up front and standing in the back).
In terms of velocity the ASG CZ 75 BB Pistol shoot fairly conservative at just under 300fps. The noise this CO2 Licensed Replica Pistol makes is fairly quiet making it a good choice for the backyard if you have neighbors to consider. I also found the blowback to be mild since the amount of CO2 being released with each shot seems to be minimal.
Stepping back 30 feet and shooting at my paper target, the ASG CZ 75 CO2 Blowback BB Pistol produced a decent 2-2.5 inch 10 shot grouping that was just a little to the left and a hair low. The trigger is super light and the release is crisp, I actually had to get a bit used to how light the trigger was as I was shooting a bit early and before I was ready since only a slight bit of pressure is required.
I would like to see just a bit higher fps from the ASG CZ 75 CO2 Blowback BB Pistol, that would also give it a little bit more blowback kick but even the 300-ish fps out of the box, the ASG CZ 75 is a really nice pistol to shoot with it's super responsive trigger!
In this Field Test Shooting video I test out the performance of the Gletcher SS 2202 Metal Slide using my Chronograph to get a real world Feet Per Second rating, I also step back 30 feet and shoot 10 rounds at a paper target using a semi rested position (Sand bag up front and standing in the back).
In terms of velocity the Gletcher SS 2202 Metal Slide CO2 BB Pistol performed very close to the KWC SP 2022 review I did earlier shooting as high as 468 fps. I did have some chronograph miss-readings that made the average come down a bit but I would say a flawless string of readings would have been around 450+ fps.
Stepping back 30 feet and shooting at my paper target, the Gletcher SS 2202 CO2 BB Pistol produced a respectable 4 inch grouping that was just a little to the left but not by too much. I really like the trigger on the Gletcher SS 2202 CO2 BB Pistol, for a double action only pistol it is very smooth, light and not overly long! The release is very predictable and there is zero stickiness in the first stage.
The fairly high fps for a shorter barrel pistol is most likely due to a more than average amount of CO2 released per shot but even so you can expect close to 100 shots per CO2. If you plan on using the Gletcher SS 2202 in your back yard, keep in mind that it is louder than most CO2 BB pistols, it really gives a nice loud crack with each shot.
All in all a real decent performance out of the Gletcher SS 2202 Metal Slide CO2 BB Pistol, if you are a Sig Sauer fan like I am then this Sig Pro replica is a no brainer to have in your collection!
Trigger Pull: The trigger pull on the Gletcher Metal Slide SS 2202 is double action only but is very smooth and fairly light, it does allow for some pretty quick shooting even though it is double action only. When you pull the trigger the internal barrel moves back into the magazine while the internal hammer moves rearward and then releases forwards striking the CO2 valve releasing CO2. It is a very simple yet effective design.
Accuracy: I have not done any preliminary shooting with the Gletcher SS 2202 Sig Pro Replica so other than how the trigger feels I can not comment too much on the performance. If I where to base my result on the performance of the Cybergun Sig Sauer SP 2022 I tested previously, then I can expect very high fps and good overall accuracy, we will have to wait and see...
Build Quality:Build quality was very good, I was extremely pleased with the fit and finish of my Gletcher SS 2202 BB Pistol! The metal slide and polymer frame along with the all metal full size drop out magazine gave this BB air pistol a really nice balance and weight to it. I would expect it to feel in weight and balance very similar to the real steel version since they are both constructed similarly.
Realism: The Gletcher SS 2202 Air Pistol is very close to the look, weight, and feel of the real Sig Sauer SP2022 Sig Pro! For a lower cost airgun, I was very impressed with all the details and closeness to the real steel Sig Pro. There is no actual Sig Sauer licensing on the Gletcher SS 2202 but other than that it is pretty much identical in appearance. It would have been nice to have a working slide and slide catch release but at least you have the ability to take the slide off for cleaning and oiling if required.
Pros:
Good weight and solid feeling gun.
Metal slide.
Full size all metal magazine.
Very Accurate Sig Sauer SP2022 replica without licensing.
May have good FPS! Fingers Crossed!
Fairly affordable.
Nice light and quick double action trigger.
Picatinny rail for accessories.
Cons:
No blowback - slide does not move either
Hammer does not move at all.
Non adjustable rear sight.
Comments:
I have always been a big Sig Sauer fan so I like the look and feel of the Gletcher SS 2202 Metal Slide CO2 BB Pistol. I would love it even more if it had a working slide with blowback action but then again the non-blowback version keeps things simple so should be super reliable and have good power. I am optimistic about the fps performance of this pistol since I got such good results when I tested my Cybergun distributed version a while back. Stay tuned for my Field Test Shooting Review for this pistol to find out how it does...
My Vimeo Table Top Video of the Gletcher SS 2202 Metal Slide CO2 BB Pistol:
Trigger Pull: The trigger pull on the Gletcher Grach NBB is nice in both double and single action modes. Double action is fairly light as the hammer spring tension is moderate but there is a fair bit of trigger pull length, Racking the slide or pre-cocking the hammer will allow for single action shots which reduces the trigger pull but you still have the full range of trigger take-up before the hammer is released.
Accuracy: I have done no preliminary shooting with the Grach NBB BB pistol so other than how the trigger feels I can not comment too much on the performance. I would expect to get pretty close to the factory claimed fps based on my other testings with Gletcher products. With it's single action trigger and white dot sights I am hoping for a fairly tight grouping when I perform my accuracy test later on.
Build Quality: The Gletcher Grach NBB CO2 BB Pistol is well made, the black semi-gloss finish looks really nice and the fit is good, not much of slide wiggle to speak of and pretty much the entire pistol is metal including the frame, slide, trigger, slide catch-release, safety, hammer, magazine and inner and outer barrel. The only plastic parts would be the grips and some internal seals and o-rings.
Realism:The Gletcher Grach is a 1 to 1 replica of the Russian Yarygin (MP-443 Grach), all the mechanical parts function just like you would find on the real steel version. The only indicators that it is not a real Yarygin would be the smaller barrel opening since the 4.5mm BB barrel is not recessed at all. Even the weight is near identical to the original MP-443 Grach coming in only 10 grams heavier.
Pros:
Good weight and solid feeling gun, over 2 pounds
Pretty much an all metal pistol
Full size all metal magazine
Working slide that also locks back
Very Accurate Yarygin (MP-443 Grach) replica without licensing
Fairly affordable
Nice light and quick double action trigger, also shoots in single action.
Field Strippable.
Cons:
No blowback
Barrel is not recessed.
Non adjustable rear sight.
Comments:
Without shooting this gun so far all I can comment on is how nice it looks and feels, the Gletcher Grach NBB really is a well made and detailed CO2 air pistol mirroring the original real steel Yarygin (MP-443 Grach) almost exactly. Pretty much everything is metal on this pistol helping it come in only 10 grams off again of the original. I like the single and double action trigger / hammer and the working slide and slide catch release that locks back when the BB magazine is empty. I am really looking forward to giving this gun it's field test shooting review!
My Vimeo Table Top Video of the Gletcher Grach NBB CO2 BB Pistol:
As with my standard Field Test Shooting Reviews, I shoot 5 rounds through my Chronograph to get a real world Velocity reading in feet per second. I also shoot 10 rounds into a paper target using a semi-rested position from 30 feet away. Since I had two versions of the EKOL ES 66, the long and short barreled versions I decided I would test pistols both on the Chrony and just the long barrel version for the accuracy testing.
So how did the EKOL ES 66 and ES 66C CO2 BB Pistols both do? In terms of fps, they both got into the 400+ range with the shorter barreled ES 66C version averaging 402 fps from 5 shots and the the longer barreled ES 66 getting a 444 fps 5 shot average. I was expecting the longer barrel ES 66 to outperform the shorter barrel ES 66 so this was no surprise. The temperature was not all that warm on this day but I did keep both guns fairly warm inside right up till I went outside and shot them. On a warmer day I would expect even better results.
Now for the accuracy results and don't hold your breath on this one... I have to say that the EKOL ES 66 was one of the worst BB guns I have shot to date in terms of accuracy at 30 feet. I could actually see the BB's curving after about 20 feet out, almost like they had some random spin on them? Perhaps the rifled barrel was catching a bit of grip on the smooth steel BB's and making them spin? Because this was so random it was hard to predict where the BB's where going. I also found that the EKOL ES 66 was sighted in way to high so at 30 feet I needed to aim very close to the bottom of the target and even still, about half of the BB's went well over and did not find the paper target. Perhaps actual lead BB's may be better in this pistol?
One thought I had was to somehow smooth out the rifling on the barrel as perhaps it needs to be worked in before more consistent shots can be obtained?
It was really too bad that I did not get the accuracy results I was looking for with the EKOL ES 66 Series of CO2 BB Pistols, I really like the overall quality and design of these Turkish made CO2 BB Pistols. Again perhaps some barrel work could improve the accuracy and make this a more well rounded BB gun.
