I'm getting close to uploading 600 videos now over on the Replica Airguns Vimeo channel, so there are bound to be a lot of similar questions and popular discussions. In this Replica Airguns Vimeo Video I address what I feel are my Top 10 Most Common Airgun Questions and Discussions.
While the weather is still nice, I decided to setup some clay pigeon targets at varying further out ranges than the typically 30 feet I shoot on my deck. So I figured 40-60-80-100 foot ranges would be a good test to see if a 4.5mm Steel BB rifle could effectively hit targets at any of these ranges.
I did do a similar test earlier on using my Umarex Steel Force but I think the Steel Force may have been a bit underpowered for the 80-100 foot shots.
So today I brought out my Drozd Blackbird since it has a bit of power and what it may lack in accuracy it for sure makes up in volume! As with many of my shooting videos I captured all the fun using a bunch of different cameras and camera angles and today I even wore a dedicated lapel mic which I have a min-review for coming up shortly!
So make sure to watch my YouTube video and see how the Baikal Drozd Blackbird does shooting clay pigeons up to 100 feet away...
This Article and Video expresses my views and opinions on this matter and should not be taken as legal advice.
Main points covered:
Uncontrolled Firearms do not require a Firearms License within Canada to own and operate.
What is an Uncontrolled Airgun and Airsoft Gun?
What is an Uncontrolled Blank Gun / Starter Pistols?
What about Fully Automatic Airguns and Airsoft Guns?
What about Replica Guns?
NOTE: Controlled Firearms require a POL (Possession Only License) , PAL (Possession Acquisition License) or R-PAL (Restricted Possession Acquisition License) within Canada to own and operate.
Firearm – a barreled weapon from which any shot, bullet, or other projectile can be discharged and that is capable of causing serious bodily injury or death to a person, and includes any frame or receiver of such a barreled weapon and anything that can be adapted for use as a firearm.
“Uncontrolled”firearms are those devices that, although falling within the definition of a firearm in the Criminal Code, are exempt from specific legal requirements of the Firearms Act and its regulations, as well as from other legislative provisions. “Uncontrolled” firearms should not be subdivided into any of the non-restricted, restricted, or prohibited classes. The following types of firearms are deemed “uncontrolled”:
Flare, blank, rivet and industrial guns: Any device that is designed exclusively for signaling, for notifying of distress, or for firing blank cartridges or for firing stud cartridges, explosive-driven rivets or other industrial projectiles, provided that the importer intends to use it only for the purpose for which it is designed.
NOTE: (Toy guns and starter pistols do not generally qualify as firearms. However, some toy or model guns and starter pistols may be designed with very realistic mechanisms or appearances (e.g., color, size, scale, translucency) and resembling a real make and model of a firearm. In such cases, they may be considered replica firearms even if they are made of plastic, die cast zinc, or other material.)
Low muzzle velocity/energy guns: Any barreled weapon that is not designed or adapted to discharge projectiles at a muzzle velocity exceeding 152.4 meters per second (500 feet per second) and at a muzzle energy exceeding 5.7 Joules, or to discharge projectiles that are designed or adapted to attain a velocity exceeding 152.4 meters per second (500 feet per second) and an energy exceeding 5.7 Joules. Both thresholds of 152.4 mps and 5.7 Joules must be exceeded for the firearm to be considered “controlled”. This requirement exempts firearms that fire below the threshold velocity with a standard projectile, but exceed the threshold velocity when fired with a high-velocity projectile.
Airsoft guns and certain types of paintball guns or markers may qualify as a replica firearm, if the muzzle velocity of the projectile does not cause serious bodily harm and their external features are clearly designed to resemble a specific and readily identifiable make and model of a firearm. To be considered a firearm, within the meaning of the Criminal Code, an airsoft gun must have a muzzle velocity in excess of 111.6 meters per second (366 feet per second).
NOTE: This memorandum used to state when using a .20 gram BB but does not specify this BB weight anymore?
NOTE: The term air gun is a colloquial term referring to BB or pellet guns. Such guns operate either as spring- powered, gas-powered, or electrically powered. If the muzzle velocity of the air gun is less than 152.4 mps (500 fps)/5.7 joules but still able to cause serious bodily injury to a person, it may be considered an “uncontrolled” firearm. Airsoft guns and certain types of paintball guns may qualify as a replica firearm (see paragraph 49 of this memorandum).
Replica firearms:
“Replica firearm” is defined as any device that is designed or intended to exactly resemble, or to resemble with near precision, a firearm, and that itself is not a firearm, but does not include any such device that is designed or intended to exactly resemble, or to resemble with near precision, an antique firearm.
For a device to be a replica firearm it must meet all three requirements:
(a) it cannot be a firearm, meaning it does not discharge a projectile with sufficient energy to cause serious bodily injury or death to a person. If the device is a firearm, then it cannot be a replica firearm (and vice versa);
(b) it must resemble exactly, or with near precision, a real existing firearm of an identifiable make and model. With respect to visual examination, note that the maximum observing distance is one at which the equivalent make and model of the firearm can be identified. This distance will vary from one firearm make to the next. For example: A Luger pistol has a very distinctive silhouette as compared to other makes and is therefore more readily identified from further away. The examination of the object is something more than casual, but less than detailed. The device does not need to be so close that markings are identifiable; and
(c) it cannot be designed or intended to exactly resemble, or to resemble with near precision, an antique firearm.
1. Air guns that are "Controlled" Firearms for purposes of both the Firearms Act and the Criminal Code
These are air guns with both a high muzzle velocity (greater than 152.4 meters or 500 feet per second) and a high muzzle energy (greater than 5.7 joules or 4.2 foot-pounds). The "muzzle velocity" is the speed of a projectile at the instant it leaves the muzzle of a gun, normally expressed in meters per second or feet per second. The "muzzle energy" is the energy of a projectile at the instant it leaves the muzzle of a gun, expressed in joules or foot-pounds. Air guns need to meet both standards to be classified as "Controlled" firearms for purposes of the Firearms Act.
These high-powered air guns are subject to the same license and registration requirements as a conventional "Controlled" firearm. Owners and users are also required to store, transport, display and handle them safely in accordance with the regulations supporting the Firearms Act.
Usually, the manufacturer's specifications are used to determine what muzzle velocity and muzzle energy an air gun was designed to have. This information may be available in the user's manual or on the manufacturer's website. If the information is not available, individuals can call the Royal Canadian Mounted Police Canadian Firearms Program (CFP) at 1-800-731-4000 and ask to speak to a firearm technician to find out if the air gun is considered to be a firearm for purposes of the Firearms Act.
High-powered air rifles are generally classified as non-restricted firearms. However, the classification depends on the exact design of the air gun. Air rifles manufactured to resemble an assault rifle could be non-restricted, restricted or prohibited depending on the exact model imitated. High-powered air rifles would also be prohibited firearms if fully automatic or if they have a sawed-off barrel. They could also be restricted firearms if they have a folding stock that reduces the overall length to less than 660mm.
Additional thought on this subject: Even though Uncontrolled Firearms are not governed by the same laws that apply to Controlled Firearms within the Firearms act and do not need to be handled or stored similar in the same way you are required to handle, transport and store a Controlled Firearm, we need to treat our Uncontrolled Airguns, Airsoft Guns and Blank guns with care and go over and above what is expected when had handle, transport and store them.
You guessed it, another Full Auto Fun YouTube Video! And another great Blowback BB gun from the past dusted off and brought out for some more shooting fun :)
You may remember my Cybergun GSG 92 CO2 Blowback 4.5mm Steel BB Pistol that I made several video reviews of, including a how to modify it to shoot both in semi auto and full auto modes. Well the good news is our new KWC Model M92 unlicensed versions (no ugly warning lettering either) now come with the semi and full auto selectable feature so no need to modify, just buy one and your ready to go!
With that said this video is me actually shooting my original Cybergun / KWC Licensed GSG 92 version that I modded to shoot full auto. It was giving me a bit of trouble today but it seemed to work out the kinks near the end.
In an upcoming Full Auto Fun Video I do plan to bring out a new KWC full auto ready M92 and Mini UZI to see how these factory full auto 4.5mm BB guns shoot out of the box.
Some more Full Auto Fun Videos coming at you and make sure to check my previous ones out too!
In this Full Auto Fun Field Test Shooting video I bring out my original Umarex Walther PPK Blowback CO2 BB Pistol. The PPK I converted to full auto and that started it all off by being my first YouTube video upload. Wow, that was a while ago now!
I do have to say, modifying the PPK to Full Auto is not recommended, mine originally worked well but the heavy blowback in full auto eventually broke the firing pin setup and I lost it somewhere in my back field. I had to Macgyver a bolt in place to kind of work but now my Full Auto Modded PPK shoots out of control, what I mean by this is when I press the trigger, it does not stop shooting until all the BB's are gone. Safe, I don't think so!
My suggestion is to leave the Umarex Walther PPK as is, it truly is a an awesome CO2 Blowback BB replica with some really decent blowback recoil in a small airgun.
Full Auto Fun video number three this week and this one is perhaps the craziest one! When you take a Drozd Blackbird that already has a 800-1000 round BB magazine, convert it to 1200 rounds of full auto, add a custom JimC Barrel to it, some bulk CO2 and a bunch of other cosmetic accessories... Well you get the most ridiculous full auto BB gun you can ask for.
Since I had an extra 800-900 BB's more than I am used to when making these full auto videos, I decided to add a few additional targets over and above the clay pigeons I have been using so far. I picked up a nice fairly heavy gauge Santa tin and a rather solid hard wax candle from the dollar store that proved to add some drama to this Full Auto Fun video!
Make sure to also watch my first two Full Auto Fun videos:
If you like what you see in this video and want an absolutely crazy BB gun, then checkout our Replica Airguns Store where we Sell the Drozd BB gun and some add ons for it!
This "Full Auto Fun" video focuses on my KWC/Cybergun 4.5mm Steel BB CO2 Blowback Mini UZI BB Gun, where I kick of a short series based around shooting a bunch of 4.5mm Steel BB machine guns! Sounds like fun cause it is fun!
This KWC/Cybergun Blowback Mini UZI comes in a variety of versions, 4.5mm Steel BB and Airsoft versions, it also comes in RWS and KWC Distributed models.
In this video I basically shoot a bunch of clay pigeons positioned in various locations and film it using 4 different camera angles to spice things up a bit.
I also mention some upcoming videos where I will be shooting my RAP4 MP5 and Baikal Drozd Blackbird Full Auto BB guns so make sure to watch those video when I upload them later on this week!
In this "head to head to head" pistol shootout I compare three of my more powerful, or you could say effective air pistols against each other. Shooting at some pop cans from about 30 feet away to see how destructive each one is. I don't generally recommend air pistols for pest control simply because they tend to be less accurate and powerful than rifles, especially out at the longer ranges where a magnified scope is required and notably where the pesky vermin like to hang out.
I would have to say out of the three tested in this video comparison, the Webley Alecto in .22 caliber and the Modified Drozd Full Auto BB Gun would for sure get the job done at closer ranges. The Webley Alecto simply because it can hurl a heavy grain .22 caliber lead pellet right around the 500 fps mark which will take down small pests, again at close ranges.
My second choice or even first choice depending on how active the pest are would be my modified full auto 1200 rounds per minute Drozd that hurls 4.5mm Steel BB's at over 500 fps (under 4.2 foot pounds) at a rate of 20 BB's per second! A 4.5mm Steel BB traveling at 500 fps will penetrate fur and feathers very well and with most of the 20 BB's hitting a target in a matter of 1 second, that is going to humanly put a small to even medium sized pest down for sure. And yes the Drozd becomes a pistol when yuo take the rear stock off ;)
My last choice for the job is the Xisico XSP180 in .177 caliber since like the Webley Alecto it is only a single shot, so you got to make it count and being that it has less overall energy than the Webley Alecto again I would prefer the Alecto over the XSP180.
Watch my "head to head to head" Vimeo video to see how these three pellet pistols compare:
So it's 2014 but I still needed to make my 2013 Airgun, Airsoft Gun and Blank Gun Collection Favorites for 2013. It's become a tradition I guess you could say. No I do not show all the guns in my collection but I do cover most of my favorites and also some new guns I picked up in 2013.
Here's a peek but make sure to watch the YouTube video bellow where I go over all my top picks for 2013. You can also buy many of the guns I show in this YouTube video over in our Canada and US Replica Airguns Store!
2013 BB Pistols
2013 Pellet Pistols
2013 Airsoft Pistols
2013 Blank Pistols
2013 Rifles
Another quick revisit of the KWC/Cybergun M92 Beretta - Taurus full metal, full blowback, CO2 4.5mm Steel BB pistol series. They come in several flavors but are all made by KWC and in many cases redistributed licensed by Cybergun. This Field Test Shooting Video Review focuses on the Cybergun Swiss Arms P92 version.
I have several videos I made for the Cybergun GSG 92 version showcasing an early on Table Top Review, Field Test Review and even a Full Auto Mod Video.
Now that I have a more standardized Field Test Shooting format, I though I would revisit this series of KWC/Cybergun Beretta - Taurus Replica BB Pistols and do a follow up Field Test to get some more camera angles and hopefully a nice tight target grouping using my standard semi rested position from 20 feet away.
I also incorporate some high speed video near the end of this Field Test Shooting video Review to go along with the Chronograph and target portion of the Filed Test Shooting review.
The KWC - Cybergun Full Blowback All metal serious of Replica CO2 BB Pistols has been hugely popular over here at Replica Airguns and for good reason, they are very realistic in looks and operation, are priced very respectably and replicate several of the more popular semi auto pistols.
I thought I would try some Sport Smoke Tactical Airsoft - Paintball Smoke Grenades (TSG) and show you how they work out in an open area and also when in an enclosed area (indoors). These Tactical Smoke Grenades put out a lot of smoke but will require either a non windy day or an area where the smoke can accumulate to give you good coverage. Either way they do a greta job of causing a distraction that will allow you to get into a better position.
Here is some info on the Sport Tactical Smoke Grenades for Airsoft and Paintball:
The Sport Smoke Tactical Smoke Grenade (TSG) is designed to meet the extreme needs of today's paintball and Airsoft enthusiasts. These high quality smoke grenades are very affordable, producing a thick white plume of smoke to cover your movement and provide a major strategic advantage.
I wanted to cover some basic Airgun, Airsoft Gun, Blank Gun and Paintball Gun information on what do they all shoot, what makes them shoot and some other miscellaneous info thrown in along the way...
Your should also watch the video attached at the bottom of this post as it goes into a fair amount of detail.
Let's begin with the types of ammo used:
Airgun Ammo
Airgun ammo for the most part is broken down into BBs and Pellets, the most standard size BB and Pellet is the 4.5mm or .177 caliber Steel BB and Lead Pellet. You can also get Pellets in other calibers and even other materials other than lead such as steel or aluminum, some can have plastic skirting around a metal interior.
Pellets also come in a variety of caliber's like .177, .20. 22. 25 and even larger but then I would start considering them to be bullets as they will take on the shape of a bullet when they get into the larger sizes.
Airgun Ammo is not be fired at people, it is primarily used for target and hunting small game.
Airguns can use Spring Pistons, CO2, Compressed Air and Multi-pump propulsion systems.
Airsoft Gun Ammo
Airsoft Guns for the most part shoot round 6mm (.22 caliber) plastic BBs which come in a variety of weights ranging from .12 grams up to .48 grams. There are larger Airsoft BBs such as 8mm and even larger.
There are biodegradable and even tracer florescent Airsoft BBs available.
Airsoft Ammo is traditionally used for Airsoft battles and can be fired at people using protective gear. Airsoft Ammo can also be used for target shooting.
Airsoft Guns can use Spring Pistons, Spring Piston - AEG (Electric Motor) CO2, Gas (Green, Red, Propane) and Compressed Air propulsion systems.
Paintball Gun Ammo
Paintball Guns or "Markers" have been historically used for the sport of Paintball but their whereabouts came from the need of ranchers and forestry workers to mark trees. Hence the name "Marker"
Paintball ammo comes in a variety of sizes ranging with the most common being .43 and .68 caliber. They are generally made from a gelatin outer coating containing primarily polyethylene glycol, other non-toxic and water-soluble substances, and dye, they are usually biodegradable.
Paintball Guns can also shoot a variety of Paintball Ammo that can be made out of Rubber, Plastic, Glass and they can also contain Powders and even Pepper for use in non lethal defense.
Paintball Guns can generally use either CO2 or Compressed Air as their propellant.
Blank Gun Ammo
Blank Guns are just like Real Guns but without the dangerous bullet at the end of the brass shell. Other than that they work exactly the same as a Real Gun!
Blank Guns are used when a bullet is not required or even wanted. For instance... Gun safety, gun training, training animals to be around guns and/or loud noises, Props for Movies - Stage - Film - TV, Collectors that do not want the red tape associated with owning a Real Gun or when owning a Real Gun is prohibited.
Blank Guns can shoot a variety of sized ammo, most common are .22 caliber crimped, .380 crimped, 8mm P.A.K. and 9mm P.A.K.
Blank Guns use gun powder as their means of operation.
Here are the most common forms of propulsion used in the guns we discussed earlier:
CO2
CO2 is the most common propellant in Airguns (BB and Pellet), it is also used in Airsoft Guns and Paintball Guns.
CO2 is a compressed gas which expands when released, it requires a warm environment to fully expand and tends to cool it's surroundings quickly when shot fast or in full automatic which can slow the velocity of the projectile and even freeze up the gun being used.
The most common reusable CO2 cartridges are 12 and 88 gram but you can get larger CO2 tanks in a variety of sizes that can be refilled with CO2.
Gas
Gas is used primarily in Airsoft Guns, I have not personally seen an Airgun that is made to use Gas other than CO2.
Gas is similar to CO2 in that it is a compressed gas that expands when releases, it also cools down the gun it is being used in and requires a warm environment.
Gas comes in a variety of names, Green Gas, Red Gas and Propane Gas. Green Gas contains Propane as it's base but has additives in it like silicone for lubrication .
Red Gas is know to be a bit more powerful than Green Gas as it has Chlorodifluoromethane or HCFC-22, R22 or Freon 22 used in refrigeration which turns to a liquid under a slightly higher pressure giving you slightly higher fps.
Many people use propane gas with an adapter that allows the mixture of silicone as propane is cheaper to buy.
Compressed Air (HPA)
Compressed Air (HPA - High Pressure Air) is most commonly used in Airguns and Paintball Guns but some people use it for their Gas based Airsoft guns.
The compressed air comes from high PSI tanks that can be purchased in a variety of sizes and contains compressed air at pressures up to 5000psi.
These tanks are reusable and usually need to be refilled at a paintball or scuba shop, some people buy their own compressors or large scuba tanks for refilling purposes.
Some Compressed Air (HPA) guns have their own built in tanks that can be filled with a compressor or even a manual pump.
Compressed air does not cool down the gun it is being used in and is a great option for high output or fully automatic guns.
Multi-Pump Pneumatic
Multi-Pump Pneumatic systems are most commonly used in Pellet and/or BB guns.
Multi-Pump Pneumatic guns use the same principle as HPA - High Pressure Air guns in that they require pressurized air as the propellant. The main difference with Multi-Pump Pneumatic guns, is that you do all the work by pumping the gun between shots. Generally speaking you pump the gun 3-10 times, take a shot and repeat this process.
Multi-Pump Pneumatic guns are not effected by air temperature and are great for target and small pest control.
Spring Piston
Spring pistons are generally found in Pellet Rifles and Pistols but some Airsoft Guns also use a Spring Piston System and generally speaking Spring Piston Guns are single shot only or in other words, the Spring needs to be drawn back before each shot. Spring Piston Guns can have magazines that allow for quicker repeat shots.
Spring Piston Guns come in many cocking configurations, Brake Barrel and Side lever to name a couple.
The Spring can be a Mechanical Spring or a Gas Spring.
Spring Piston Guns are not effected by temperature and are often used for small game hunting and target shooting.
Automatic Electric Guns (AEG)
Automatic Electric Guns are generally found in Airsoft Rifles but there are some Airsoft Pistols (AEP) that use this same system.
Automatic Electric Guns use a similar system to a Spring Piston gun but have an electric motor that does all the work of drawing back the spring. You can even have fully automatic AEG guns.
The power for the electric motor comes from removable batteries, so it is a combination a battery supplying the motor with the power to draw back the spring that creates a pillow of air that shoots the BB.
AEG Airsoft Guns are great for situations when you require high capacity magazines with full auto capability.
Gun Powder
Gun powder is used in Blank Guns, in the same manor that it is used in a Real Gun, the charge from the Gun Powder supplies the force required to operate the blowback in most semi auto Blank Pistols, it also creates the sound of a live round along with the muzzle flash which makes Blank Guns great for training and as Props for Movies and Film.
Because the kinetic energy from a blank gun is the same as a real gun, blank guns can be very dangerous when used in close proximity to an object, see my "Are Blank Guns Dangerous Video"!
Some other Gun Relevant Terminology:
Blowback
Blowback operation is when some of the force of the propellant is used to move the slide backwards, which in most cases cocks the hammer for single action and can also pickup and chamber a round into the barrel.
The slide spring supplies the energy for the return to the forward position of the slide.
Blowback Guns do rob some power from the bullet force and in the case of CO2 or Gas Guns the also reduce the amount of shots per CO2 or Gas fill.
Revolver, Semi Automatic
Revolver: Revolvers feed ammunition via the rotation of a cartridge-filled cylinder, in which each cartridge is contained in its own ignition chamber, and is sequentially brought into alignment with the weapon's barrel by a mechanism linked to the weapon's trigger (double-action) or its hammer (single-action)
Semi Automatic: semi-automatic pistols use the energy of one shot to reload the chamber for the next. Typically recoil energy from a fired round is mechanically harnessed. After a round is fired, the pistol will cycle, ejecting the spent casing and chambering a new round from the magazine, allowing another shot to take place immediately.
Single Shot, Repeater, Semi Automatic & Fully Automatic
Single Shot: A Single Shot Gun needs to be reloaded each time it is shot.
Repeater: Repeating action Guns are single barreled guns containing multiple rounds of ammunition. These rounds are loaded from a magazine by means of a manual or automatic mechanism, and the action that reloads the rifle also typically re-cocks the firing action. The term repeating rifle is most often applied to weapons in which the next cartridge is loaded by a manual action, as opposed to semi-automatic rifles, in which the force of one shot is used to load the next.
Semi Automatic: A semi-automatic, or self-loading, firearm is a weapon that performs all steps necessary to prepare the weapon to fire again after firing.
Fully Automatic: A Gun that uses either its recoil or a portion of the gas propelling the projectile to remove the spent cartridge (in the case of a gun-shell), fire again repeatedly, as long as the trigger is held down or until the magazine is exhausted. Automatic Guns are distinguished from semi-automatic Guns in their ability to fire more than one shot in succession once the trigger is pulled.
Single, Double Action, SA/DA
Single-Action (SA): trigger performs the single action of releasing the hammer or striker to discharge the firearm each time the trigger is pulled.
Double-Action (DA): The trigger both cocks and releases the hammer or striker
SA-DA: A SA/DA firearm combines the features of both mechanisms. You can pull the trigger in Double Action when the hammer is down which cocks and releases the trigger or you can cock the hammer with your thumb and then release the trigger using Single Action to fire the weapon.
Lever Action, Pump Action, Bolt Action
Lever Action: In a classic lever-action firearm, rounds are individually loaded into a tubular magazine parallel to and below the barrel. A short bolt is held in place with an over center toggle action. Once closed, the over center action prevents opening solely by the force on the bolt when the weapon is fired. This toggle action is operated by a hand grip that forms part of the trigger guard. When operated, a spring in the tubular magazine pushes a fresh round into position. Returning the operating lever to the home position chambers the round and closes the breach.
Pump Action: With a pump-action firearm, the action is operated by a movable fore-end that goes backwards and forwards to eject, extract, and chamber a round of ammunition. Pump-actions are usually associated with shotguns.
Bolt Action: The bolt opens and closes the breech end of the barrel and contains the firing pin. The bolt is held in place with a lever that fits into a notch. Moving this lever out of the notch will release the restraint on the bolt, allowing it to be drawn back. An extractor removes the spent cartridge, which is then ejected through the lever slot. A spring at the bottom of the magazine pushes up the reserve rounds, positioning the topmost between the bolt and the chamber at the base of the barrel. Pushing the bolt lever forward chambers this round and pushing the lever into the notch locks the bolt and enables the trigger mechanism.
Magazine vs Clip
Magazine: A magazine is an ammunition storage and feeding device within or attached to a repeating firearm. Magazines can be removable (detachable) or integral to the firearm. The magazine functions by moving the cartridges stored in the magazine into a position where they may be loaded into the chamber by the action of the firearm. The detachable magazine is often referred to as a clip, although this is technically inaccurate.
Clip: A clip is a device that is used to store multiple rounds of ammunition together as a unit, ready for insertion into the magazine or cylinder of a firearm. This speeds up the process of loading and reloading the firearm as several rounds can be loaded at once, rather than one round being loaded at a time. The term "clip" is also frequently used to refer to a detachable magazine, though such usage is incorrect.
Type: Airsoft Pistol.
Manufacturer: Umarex.
Model: Walther P99 DAO
Materials: Metal & Polymer.
Weight: 1.5 pounds.
Barrel: 4 inches, metal non-rifled.
Propulsion: 12 gram CO2.
Action: Semi auto, double action only with blowback.
Ammunition Type: 6mm plastic Airsoft BB's.
Ammunition Capacity: 15 round stick magazine.
FPS: 380.
Trigger Pull: The Double Action Only trigger pull on the Umarex Walther P99 CO2 Blowback Airsoft Pistol is long but not overly heavy for a double action trigger, it does have a break point mid way where it locks partway back, I presume this is the point in which a BB is loaded from the magazine into the barrel? The rest of the pull is still medium but much shorter with a distinct release point.
Accuracy: I did do a quick preliminary test before I made this table top review to get an idea of where this gun performs in terms of FPS and accuracy, I shot 5 rounds through my Chronograph on a fresh CO2 and got an average of 333FPS which was a bit lower than the claimed 380 but it was not the hottest of days. I also stepped back 20 feet and from a semi rested position I was able to get 9 shots within 2 inches of each other which was not bad for a DAO gun that I have never shot before. I did shoot a bit down and to the left with the set sights.
Build Quality: The Umarex Walther P99 is well built for its rather low price tag, it may not have all the bells and whistles but it does get the job done with good fit and finish and materials used. You will find a plastic/polymer frame but there is a lot of metal where it would normally be found on the real steel version like in the slide, magazine, trigger, slide catch, magazine release, inner barrel and many other internal parts. No real complaints here!
Realism: The Umarex Walther P99 CO2 Blowback Airsoft Pistol is pretty close in looks to a real steel Walther P99 with the exception of a missing decocker, but I'm pretty sure this is the same with the real steel DAO version? There is also the funny looking safety on the right side of the frame found on many Umarex airguns. I have to mention the red tip but again this can be removed and even when removed the barrel it is still recessed which adds to the realism. The Blowback action, Walther licensing and nice heavy weight all add up to make this Airsoft pistol look and feel the part.
Purchase it from: The Replica Airguns Store
Pros:
Low cost for a very believable and solid replica.
All metal stick magazine.
Metal slide and internal parts gives it decent weight.
Rail for accessories.
Well hidden CO2 screw.
Walther licensing.
Recessed inner barrel.
White dot sights, easy to use.
Right amount of power for indoor CQB style airsoft games.
Cons:
Comes with a red tip even in Canada.
Double action only, so trigger is a bit heavier.
Kind of funny safety, not like the real gun.
Blowback was a bit sluggish.
Comments:
Overall the Umarex Walther P99 CO2 Blowback Airsoft Pistol is a very good buy, it's a decent replica of the real steel Walther P99 with blowback operation, lots of metal parts, good fit and finish, decent performance and full Walther licensing and trademarks. All at a very affordable price tag. It may lack some of the extras you will find on more expensive and more functional Airsoft pistols but the simplicity of the Umarex Walther P99 CO2 Blowback Airsoft Pistol means it will most likely be a bit more reliable with less to go wrong down the road. If you have been looking for a nice Walther styled replica in an Airsoft version this may be just be the ticket!
My Vimeo Video Review for the Umarex Walther P99 CO2 Blowback Airsoft Pistol:
Here is a quick Update video of three Airsoft guns, two of which I have touched upon before but have not gotten around to doing any actual Table Top or Field Test Shooting videos for you (The ASG Dan Wesson Airsoft Revolver and the Umarex P99 Blowback Airsoft Pistol). I also show you a new Umarex Airsoft Gas Blowback PDW, the H&K MP7 A1, a very realistic version I am sure will be of interest to many of my Airsoft fans.
I will be doing proper Table Top and Field Test Videos for each of these Airsoft guns as soon as I can get to them all, starting with the Umarex Gas Blowback H&K MP7 A1 Airsoft PDW so stay posted for these upcoming video reviews...
After many many requests to show how the Umarex Walther PPK CO2 Tab Modification is done I have relented to public demand. I don't actually cut my tab in this PPK CO2 Tab Modification Video but I do go step-by-step in detail and compare my modified Umarex PPK to my unmodified Umarex PPK. It is really very basic on how this is done and only a hack say and perhaps a file are all that is required to make the modifications to the PPK CO2 tab in order to make it flush with the bottom of the handle area.
Your best bet is to simply watch my YouTube Video located below and follow the steps there but here it is in text form:
Place an empty (already pierced) CO2 into your Umarex Walther PPK and tighten the unmodified CO2 tab until fully tightened, just like you would tighten a fresh CO2.
Take note at how many threads are exposed between the bottom of the handle and the top of the plastic CO2 tab, there should be about 2-4 threads exposed.
Unscrew the CO2 tab all the way, place the PPK BB Pistol so it is secure (in a vice of some sort) and use a hacksaw or dremel to shorten the CO2 screw just above the plastic tab at the thread location you previously noted. Be conservative as you can always cut or file the screw a bit shorter if your first cut was not short enough.
Now use the same hacksaw or dremel to cut a notch in the exposed cut area of the CO2 screw so that you can use a slot screwdriver to tighten the CO2 screw.
That's it - Enjoy your modified Umarex Walther PPK CO2 BB Pistol!
Watch my Vimeo Video of the Umarex Walther PPK CO2 Tab Modification Tutorial:
This is not meant to be a full review of either the BB or Airsoft version of the Cybergun - KWC CO2 Blowback Mini UZI's but I do talk about specifications, show you around both guns, and put them both through a full Field Test so I guess in a way, perhaps it can be considered to be a full review ;)
I will list the specifications here for you but I am not going to get into details like Trigger Pull, Build Quality, Accuracy and Realism. You can check out my other video reviews for more information on the Mini UZI:
Type: CO2 Blowback Machine gun.
Manufacturer: Cybergun - KWC.
Model:Mini UZU.
Materials: Metal and Polymer.
Weight: 4.8 pounds.
Barrel: Metal, non-rifled.
Propulsion: CO2 x1.
Action: BB Semi auto only - Airsoft selectable semi & full auto, single action only.
Ammunition Type: 4.5mm Steel BB - 6mm Plastic Airsoft
Ammunition Capacity: 25 - 38 rounds
FPS: 350 - 400
As I said you can check out all my other videos for info on these very accurate Mini UZI Replicas, I mainly want to go over some of the main differences and similarities for both the BB and Airsoft versions.
In terms of build quality they are made almost exactly the same and weigh in at a hefty near 5 pounds, the only differences are the inner barrel and magazines to accommodate the different sized ammo. The BB version has a 25 round single stack magazine that does not have a follower to stop the bolt from continuing to operate even after the magazine is empty. While the 6mm Airsoft version has a double stack magazine that holds 38 rounds and does have a follower to stop the bolt which can save you some unintentional wasted CO2.
The Airsoft Mini UZI version is distributed by KWC while the 4.5mm BB version is distributed by Cybergun, you will find the UZI and IWI licensing on the Cybergun 4.5mm BB version but not on the KWC 6mm Airsoft version.
Out of the box the KWC Airsoft Mini UZI is ready to go in both semi auto and full auto while the 4.5mm steel BB version will only shoot in semi auto mode, it can however be easily modded to shoot in full auto.
Both guns come in cardboard boxes with manuals, some BB's and an Allen key to tighten the CO2. The KWC Airsoft Mini UZI also comes with a handy speed loader.
There is a slight fps velocity difference between the two with the KWC Airsoft 6mm plastic rounds traveling at around 400 fps (with .20 gram BB's) and the 4.5mm Steel BB's traveling at right around 350 fps. In the field test portion I test both guns out on some water filled cans to see how each ammo type performs in terms of penetration.
Your best bet is to watch both my Table Top and Field Test Comparison Video Reviews and see for yourself how they compare!
Type: 6mm Plastic BB Airsoft Pistols.
Manufacturer:Cybergun
Model:Sig Sauer P226
Materials: Metal slide & frame.
Weight: 2 pounds (920 grams).
Barrel: Metalnon-rifled smooth bore.
Propulsion: Gas Blowback (GBB).
Action: Single and double action.
Ammunition Type: 6mm plastic Airsoft BB's.
Ammunition Capacity: 26 rounds.
FPS: 383 fps (Using .12 gram BB's).
Trigger Pull: The trigger pull on the Cybergun Sig Sauer P226 Airsoft Replica is good in both single and double action. Once the slide is pulled back and released the first round is chambered and the hammer will remain back placing the P226 in single action mode, the pull is light and the take-up is fairly short, most of your shots will be in single action mode unless you use the de-cocker to lower the hammer for a subsequent double action next shot, double action shots are still pretty light but much longer in order to cock the hammer.
Accuracy: Shooting the Cybergun Sig P226 from 20 feet out in semi rested position I was able to get very good results. I placed 10 rounds in about 1.5 inches with the shot placement being a bit low possibly due to my barrel mod, adjusting the hop-up may bring the aim point back up to where it should be. The Sig Sauer P226 Airsoft Replica shot right around the 316 fps range while conducting my 5 shot average chrony testing which was lower than advertised but I was using much heavier .20 gram BB's. You can expect to get a full magazine worth of shots out of each gas fill-up but I did notice that as the magazine got colder it did tend to become much less efficient and also seemed to vent a lot of vapor.
Build Quality: The build quality is generally good and I was surprised at the finish on this model as the paint is not showing any wear marks so far, the fit is good with minimal slide and barrel wobble and everything is working very well with no problems so far with a fair amount of shots through it, guess you could say I like shooting this gun :) Most of the gun is metal with only the grips and a couple internal parts being plastic.
Realism: The Cybergun Sig Sauer P226 6mm Airsoft pistol is a replica of the real steel Sig Sauer P226 right down to the licensing and it really is a great looking and functioning Airsoft Replica. You can field strip this gun exactly like a real Sig and all the mechanical parts work just the same including a working de-cocker and adjustable front sight.
Available in the:Replica Airguns Store
Pros:
All metal pistol with good overall realistic weight to it.
Very crisp and firm full blowback operation.
Excellent fit and finish - paint seems to be wearing well.
Nice accurate looking and working Sig Sauer P226 Replica with licensing
Working de-cocker.
White dot sights for quick target acquisition.
Front sight is adjustable for windage.
Full size drop out magazine holds BB's and gas.
Fully field strip-able.
Buy this Airsoft Pistol in Canada - Buy this Airsoft Pistol in the US
Cons:
Comes with an orange tip not required for Canada.
Seemed to shoot a bit low for me, could adjust with hop-up a bit?
Only one magazine per Gas fill.
Comments:
I am a big Sig Sauer fan so it would take a lot for me to not give this gun a good review, with that said it performed pretty well, sure it was not the most powerful but I was using gas over CO2 so I was not expecting too much, it also shot a bit low for me but again that may have been because of the barrel mod so who really knows for sure at this point ;) And yes it came with that unsightly orange tip that I took short work of removing. At teh end of the day I still love it and it performed well without letting me down, just like a would expect from a real Sig Sauer!
My Vimeo Table Top Review of the Cybergun Sig Sauer P226 GBB Blowback Airsoft Pistol:
I usually do my Table Top Video Review first but this time around I did my Field Test Video Review first since I was all setup checking out a couple other guns at the time. When I do my detailed Table Top Video Review for the Cybgergun Sig Suer P226, I'll post the link here so stay tuned. If you have not already checked out my Barrel Mod Video for this same gun then check that video out where I remover the extended orange portion of the metal barrel and make the barrel flush with the end of the slide which is how the real steel version was originally made.
Getting back to the Cybergun Sig Sauer P226 GBB blowback Airsoft Pistol field test, as per usual I test this Airsoft semi auto gas blowback pistol on the Chronograph to see what kind of real world velocity I get and since I had some Green Gas on hand, I used it for this part of the review and got an average of 315 fps with a six shot string.
I also stepped back 20 feet and shot 10 times at my stationary target using a semi rested position (sand bag up front and kneeling in the back). Even though the Sig Sauer P226 shot a bit low I did get about a 1.25 inch group with the exception of one flyer that hooked down just a bit making the 10 shot group a bit wider at just under 2 inches. The low shot placement may have been caused by my barrel mod but since I did not do a before and after test, I can not say for sure?
Make sure to watch my YouTube Video of this Field Test as it also includes some nice slow-motion of the slide blowback at both 400 and 1200 frames per second.
Watch my full Video Field Test Shooting Vimeo Video below:
I have not done my official Table Top and Shooting Reviews for the Gas Blowback Airsoft Cybergun Sig Sauer P226 but I really wanted to cut off the ugly orange painted barrel tip, it was kind of driving me crazy! keep in mind here in Canada we are not required to have orange tips on our Airsoft guns, most of the all metal or all black Airsoft guns imported these days fall into the "airgun uncontrolled firearms" category. If you live in the US or other parts of the world you could be breaking the law if you do this mod so be warned...
Your best best is to simply watch my Vimeo Video as I show you exactly how I removed the orange painted portion of the metal barrel using a hack saw, file, vice and some sand paper. All in all it was not too difficult and only took about 15 minutes to complete...
It would not be the end of another year without another Airgun, Airsoft Gun and Blank Gun Collection video for you. This year I'm not showing all my guns, I started to take them out and quickly realized there where just way too many and this years video would have been several hours long and would have taken most of the week for me to shoot and edit...
So this year I have hand picked some of my top favorites and most notable replica Airgun, Airsoft Gun and Blank Guns. They may not all be the best made or hardest shooters or even all that accurate but each one has some significants to me.
So if you have about 30 minutes to kill, then join me in this years roundup of my most favorite Collection of guns for 2012!
Watch my Vimeo Video Airgun, Airsoft Gun and Blank Gun Collection Favorites for 2012
