I had a chance today to get out and shoot my B&W Dragunova SVD Airsoft Sniper Rifle, the weather held out just long enough for me to setup my target a good 90-100 feet out in the field but as luck would have it, it started to rain on my camera gear right as I started doing my target shooting test using .36 gram Airsoft BB's. So in a bit of a rush, I shot off a good 10 rounds and was able to put most of them on the paper which from 100 feet out using an Airsoft rifle on a target the size of a standard 8x11 sheet of paper is not too bad at all, and don't forget I was just using the iron sights.
I found I didn't even need to use the hight adjustment on my rear sight as the hop-up seemed to keep the Airsoft BB's floating nicely on plane all the way to at least 100 feet. By the way if you watched my earlier Table Top Reviews I mentioned the B&W Dragunova SVD was shooting a bit to the left even after full windage adjustment to the right, well I managed to sort this out and pull the sight the little bit extra I needed to get it pretty much dead center.
Moving on to the Chronograph portion of this Field Test Shooting Review, I got the same results as my pretest with an average fps of 498 using .20 gram Airsoft BB's and an average fps of 277 using the heavier .36 gram BB's. I have heard that the B&W Dragunova SVD Airsoft Sniper Rifle can be a bit of a chore to cock but for me it was actually pretty easy and using a left overhand approach worked well, allowing me to cock the charging handle pretty easy while keeping my finger on the trigger and the rifle in position ready for my next shot.
The iron sights and the trigger setup seem to both work very well with this rifle, I really have no real complaints and really enjoyed shooting the B&W Dragunova SVD Airsoft Sniper Rifle. If the rain hadn't been coming down on my camera gear I may have put a bunch more shots into the target for the simple reason I was having so much fun :)
Watch my Field Test Shooting YouTube Video for the B&W Dragunova SVD Airsoft Sniper Rifle:
Trigger Pull: The trigger pull on the B&W Dragunova SVD Airsoft Sniper Rifle is good overall, just a bit of initial take-up and then a medium trigger pull to release the heavy spring. You will of course nee to pull the charging handle with each shot to preload the spring.
Accuracy: My initial accuracy testing was done from about 45-50 out using .36 gram Airsoft BB's, it was a fairly windy day but even so I was able to get a nice tight 2 inch grouping using a semi rested position. I also put the Dragunova SVD through my Chronograph testing and shot both the lighter .20 gram and heavier .36 gram BB's to see what kind of fps I would get using both weights. The lighter .20 gram BB's got right around 500 fps while the heavier .36 gram BB's shot a bit lower at approximately 380 fps. I did however find that sighting the SVD in for windage adjustments (left and right) was a bit of a challenge as you can only adjust the front sight by loosening it with an allen key and make only very slight left to right adjustments. I was not able to get the SVD to shoot far enough to the right using this method so I amy need to do figure something else out, perhaps a scope setup?
Build Quality: The B&W Dragunova SVD Airsoft Sniper Rifle is not a super expensive rifle but still has a good combination of metal and plastic components. Most of the parts that you would find on the real SVD are metal including the barrel, bolt/charging handle & receiver, trigger, magazine, sights, strap rings and rial system. The stock is of course plastic with some added rubber. The B&W Dragunova SVD is not overly heavy but still has a reasonable amount of weight to make it believable. Performance was very good with no mechanical problems other than the last two BB's in each magazine do not load into the rifle.
Realism: I have never held an actual Dragunova SVD in my hands but from what I have seen in photos, it looks to be a good copy of the real steel Russian sniper rifle. Lots of metal helps pull of the realism, a working charging handle, removable bolt cover, and lots of other working components make for a believable looking and functioning version of this Airsoft BB shooting Dragunova SVD Sniper Rifle.
Lots of metal parts throughout where they would be on the real SVD.
Good power and accuracy combination.
Fairly high capacity magazine at 40 rounds.
Sights are adjustable for elevation front and back and a bit for windage.
Bolt is surprisingly easy enough to cock with either left or right hand.
Lots of upgrades available for this sniper rifle.
Inexpensive way to own a piece of history.
Cons:
Some discrepancies in the manual (180 fps and 100 round magazine)
Sighting for windage may not be adequate?
Would definitely be much nicer with the wood stocks.
Two BB's always pop out of the magazine area when empty.
Comments:
I found the B&W Dragunova SVD Airsoft Sniper Rifle to be a lot of fun to shoot, I was not sure how the charging handle system was going to work in terms of weight and easy of use to pull it back. I ended up using my left hand and reaching across and over and surprisingly this was very efficient and effective in charging the spring and allowed me to keep my righthand in place and on the trigger for very quick follow up shots. Power was as much as you would want from a sniper rifle and accuracy was also very good even in windy conditions. The only real problems I had where the two BB's that did not load from each magazine and the windage adjustments not quite allowing me to move my aim point enough for a bullseye at 50 feet out. I would recommend this B&W Dragunova SVD Airsoft Sniper Rifle and would suggest possibly adding some wood stocks and a magnified scope setup.
Every once in a while something goes wrong and your favorite BB shooter stops working as it should :( One of the most common problems I see with many of the full blowback BB and Airsoft pistols are BB's getting stuck in the gas tube. This is because this style of gun loads a BB into the breach area of the barrel every time you rack the slide forward. Of course this is only when there are BB's in the magazine.
The semi auto style of these guns is similar to that of a real gun, the blowback operates the slide which in turn moves back and then forward and loads a BB into the chamber. With a real gun, if you where to rack the slide manually again without shooting it, the chambered round would be ejected by the extractor but with a BB gun there is no extractor because there is no spent shell to eject. So multiple BB's can be loaded into the chamber area of the barrel overloading it and if the BB's have nowhere to go they just jam up and often go back into the gas tube which can cause all kinds of problems...
In this Cybergun KWC Tanfoglio Witness 1911 Stuck BB Removal Tutorial Video, I show you how to remove a BB or even multiple BB's from the gas tube area which in short requires; the removal of the slide and guid rod and spring so that you can push the gas tube forward and shake the BB out of the front of the gas tube.
Watch my Vimeo Video on how to remove a stuck BB from the Gas Tube on my Tanfoglio Witness 1911.
Testing out the ASG - Marushin CZ 75 Blowback Shell Ejecting Airsoft Pistol was not an easy one but I did manage to get thorough it! First there was the setup, I could not shoot the ASG Shell Ejecting CZ 75 Airsoft pistol on my deck or I would have fore sure lost most of my shell casings for it. So I decided to setup camp in my pool area where I have a nice large flat area off to one side, I put down a ginormous tarp in hopes to catch the radically flying shells but even this failsafe did not catch them all as I later found out ;)
As with most of my Field Test Shooting videos, I usually do a bit of a pre test to make sure the gun is functioning properly and so I shot a full magazine of my brass shells through the ASG CZ 75 and it worked like a charm, of course when I started recording the live video it decided not to work at all and I still do not know why? I was able to revert back to the plastic shell casing that came with my ASG CZ 75 Blowback Shell Ejecting Airsoft Pistol and they seemed to be working so I went with them for my testing. Interestingly enough the brass shells got much higher fps (around 300+) when I did my pretest compared to around the 250 average fps I was getting with the plastic shell casings.
Shooting on target proved to be better than I though once I raised my sight point up a bit, the gun likes to shoot a bit low but once I found the sweet spot I got three rounds within about 3/4 of an inch from just over 20 feet away in a semi rested position.
I would not recommend this Airsoft gun as an everyday shooter and there is no way you could use it in any type of Airsoft simulation as the ejected shell casings would get lost for sure and the cost to shoot the ASG CZ 75 would get very high indeed! It would be good for use in a movie or video where you wanted the realistic look of shells being ejected and did not want to use a blank gun or render the shells in post. And of course it is just really cool to have an Airsoft gun that has ejecting shells :)
Materials: Plastic slide & frame, some metal parts.
Weight: 1.4 pounds (616 grams).
Barrel: Metalnon-rifled smooth bore.
Propulsion: Propane, green gas.
Action: Blowback, single action only.
Ammunition Type: 6mm plastic Airsoft BB's.
Ammunition Capacity: 8 rounds.
FPS: 279+ fps.
Trigger Pull: The trigger pull on the ASG CZ 75 Shell Ejecting Airsoft Replica is single action only, unlike the real steel version that actually has a single and double action trigger. The single action trigger has a light to medium pull but does have a fair bit of take-up to it.
Accuracy: I did not pre-test the ASG CZ 75 as the shells fly everywhere and you really need to be able to retrieve them afterwards as the cost to replace the shell casing is rather high. I do plan to do a full Shooting Field Test where I will shoot the ASG Shell Ejecting CZ 75 through the chronograph, place some shots on a target and also capture the action of this pistol in slow motion with a high speed camera. So stay posted for that. I can say that from the few shots taken in my house, that it seems to shoot pretty hard and the shells really com flying out of this gun with force, I also noticed that a BB does have to be loaded into each shell for there to be enough back pressure to allow for a full slide blowback and ejection of each shell.
Build Quality: Even though this gun is made mostly out of plastic and from what I can tell is also made in Taiwan, it has a very good overall fit and finish. The slide slop is next to none and the licensing and markings look great. There are metal parts where they really need to be like in the barrel, hammer, trigger, safety, slide catch, magazine and a few other internal parts.
Realism: The ASG Shell Ejecting CZ 75 Airsoft Pistol is one of the most ultra realistic Airsoft pistols I have seen and mimics a real steel gun right down to the shells being ejected, how cool is that! If it had more metal then that would really top it off. Even with the plastic slide and frame it is very realistic in almost every way and even field strips just like a real CZ 75 and is fully licensed. The only feature not true to the actual CZ 75 would be the single action only trigger.
Excellent fit and finish - tolerances are very good.
Very believable working replica of the real steel CZ 75.
Fully licensed.
Fully field strip-able.
Nice heavy full size drop out metal magazine helps give it some needed weight.
Has metal parts where they need to be.
Cons:
Plastic slide and frame.
A bit low in the FPS department.
Only 8 rounds in the magazine.
Can not really use in the field, would lose too many shells.
Comments:
The ASG CZ 75 Shell Ejecting Blowback Airsoft Pistol is a very unique Airsoft gun, not very many Airsoft guns actually have ejecting shells. Just because of that I had to have it! Overall it is a pretty decent gun but I have yet to really test it out and that is the biggest shortcoming with this gun, you can't just shoot it anywhere as you need to shoot it in a place where you can recover your spent shell casings, unless of course you have all the money and shell cases in the world... That said it has a lot going for it other than the ejecting shells; Fully licensed and trademarked, blowback operation, full size drop out metal magazine and it's fully field strippable. I am sorry to say we don't offer it in out Canada or USReplica Airguns Store but we do have a similar all metal CZ 75 Airsoft offering in the form of the KJWorks KP-09 which I have done both a Table Top and Shooting Review for.
Ammunition Capacity: 13 round full size metal magazine -18 round metal stick magazine.
FPS: 428 - 380.
Trigger Pull: There is a lot of difference between the trigger on both of these guns, first off the Umarex Makarov has both a single and double action trigger/hammer while the KWC Makarov has a double action only trigger/hammer. Comparing the double action of both guns the definite advantage goes to the 4.5mm Steel BB shooting Umarex Makarov as it is shorter and lighter, the KWC Airsoft Makarov does not have a bad trigger but it is much longer and a bit heavier, but still very usable. The single action trigger on the Umarex Makarov is not really any lighter than when shooting in double action, it is however much shorter with a medium take-up and predictable release.
Accuracy: Both Airsoft and BB Makarov's performed very well in their shooting tests for me, they bot shot fairly well centered with the KWC Makarov getting all five shots in the black bullseye and the Umarex Makarov having a tighter group but just off to one side. This was good news since both guns do not have adjustable sights! They also scored very well in the velocity department shooting over their advertised claimed feet per second rating. The Umarex BB version shot a very respectable 390 fps while the KWC Airsoft pistol shot a very surprising 480 fps well over the claimed factory 430 fps. Both guns also shot very accurately out to ranges of 50 feet or so. From a single CO2 I was able to get 162 shots from the Umarex Makarov and 112 shots from the KWC Makarov before I noticed a significant power drop.
Build Quality: Neither one these Makarov replicas is going to win a prize for build quality, some shortcuts have been made to keep the price down on each model, but they are both built with mostly metal parts and they both performed perfectly for me during my testing. The Umarex 4.5mm Steel BB Makarov did have more moving parts while the KWC did weigh in a bit heavier, both guns had reasonable fit and finish to them.
Realism: In terms of being good Makarov replicas the pair for sure look the part, size and overall weight are very true to the original real Steel Makarov PM with the Umarex Makarov having a working slide, Makarov licensing and the ability to be field stripped. The KWC Makarov had a nicer recessed barrel and full size drop out metal magazine. I was not a big fan of the KWC screws on the right side slide or the Umarex exposed CO2 tab.
KWC may shoot a bit too hot for CQB Airsoft games.
Both guns do not have adjustable sights.
Comments:
To be honest when I got the KWC Airsoft BB shooting Makarov, I was not all that awe struck, the lack of a working slide, DOA trigger and screw holes in the slide put me off just a bit. This Airsoft pistol did warm up to me a lot once I shot it, I was surprised by the very high fps and how accurate it was for such a low cost Airsoft pistol. I can really see this gun being used as a backup or sidearm in an out doors style Airsoft game where you may need to shoot targets out at range where other lower powered pistols just would not be able to get out to. The Umarex Makarov has always had a place in my heart, it is just a really good little CO2 BB pistol for the price with mostly all metal parts, a working slide, single and double action trigger and very good overall performance. In my books you can not go wrong choosing either of these Makarov replicas so choose wisely!
My Vimeo Video Table Top Comparison Review for these Makarov Air Replicas:
We have been taking preorders on many of our ASG Airguns and Airsoft guns for our Canada Replica Airguns Store, we where expecting them to be back in stock right around the end of the month. The good news is we got them a bit early so we are now filling back orders and most of our ASG inventory is now showing as in stock and ready to ship!
So if you've been waiting for an ASG gun, make sure to grab yours now before we run out again...
This is not meant to be a full review of either the BB or Airsoft version of the Cybergun - KWC CO2 Blowback Mini UZI's but I do talk about specifications, show you around both guns, and put them both through a full Field Test so I guess in a way, perhaps it can be considered to be a full review ;)
I will list the specifications here for you but I am not going to get into details like Trigger Pull, Build Quality, Accuracy and Realism. You can check out my other video reviews for more information on the Mini UZI:
As I said you can check out all my other videos for info on these very accurate Mini UZI Replicas, I mainly want to go over some of the main differences and similarities for both the BB and Airsoft versions.
In terms of build quality they are made almost exactly the same and weigh in at a hefty near 5 pounds, the only differences are the inner barrel and magazines to accommodate the different sized ammo. The BB version has a 25 round single stack magazine that does not have a follower to stop the bolt from continuing to operate even after the magazine is empty. While the 6mm Airsoft version has a double stack magazine that holds 38 rounds and does have a follower to stop the bolt which can save you some unintentional wasted CO2.
The Airsoft Mini UZI version is distributed by KWC while the 4.5mm BB version is distributed by Cybergun, you will find the UZI and IWI licensing on the Cybergun 4.5mm BB version but not on the KWC 6mm Airsoft version.
Out of the box the KWC Airsoft Mini UZI is ready to go in both semi auto and full auto while the 4.5mm steel BB version will only shoot in semi auto mode, it can however be easily modded to shoot in full auto.
Both guns come in cardboard boxes with manuals, some BB's and an Allen key to tighten the CO2. The KWC Airsoft Mini UZI also comes with a handy speed loader.
There is a slight fps velocity difference between the two with the KWC Airsoft 6mm plastic rounds traveling at around 400 fps (with .20 gram BB's) and the 4.5mm Steel BB's traveling at right around 350 fps. In the field test portion I test both guns out on some water filled cans to see how each ammo type performs in terms of penetration.
Your best bet is to watch both my Table Top and Field Test Comparison Video Reviews and see for yourself how they compare!
For the most part, this video is to test out some cameras and using them all together in a multi-camera scenario. I wanted to see how many camera angles I could shoot at one time and see how they would all work together when editing the video.
Cameras used:
My new Pivothead Recon Camera Glasses.
Sony HDR-AS15 Action Cam.
Drift HD170 Point of View Camera.
Nikon 1 with 10mm fixed lens.
Casio TRYX.
*All cameras where shooting in 1080p for this video.
I hope to use camera setups like this in the future, maybe not all at once but at least a couple at a time to give you some viewing options.
I picked out my WE SCAR GBB Airsoft Rifle for this test as it had a lot of mounting points and the Gas Blow Back makes for some great video action. Unfortunately My WE SCAR was not working at 100% but I still think I was able to pull off this test video either way.
Watch my Multi-Camera-Angle Test Video shooting the WE SCAR GBB AIrsoft Rifle:
The KWC/Cybergun Model 1911 Blowback BB Pistols and Airsoft Pistols are very popular and so I tend to get lots of questions about them like: Are they the same quality? What version shoots the best? How do I remove the white warning lettering? Can I get one in an Airsoft version? Can I add a laser or tactical light? Can I change the grips...
So in this YouTube video I compare all four existing KWC and Cybergun model 1911's showing you the Cybergun Tanfoglio Witness 1911 in 4.5mm Steel BB, the KWC Model 1911 and Model 1911 A1 Tac also in 4.5mm Steel BB and lastly the KWC Model 1911 in 6mm Airsoft plastic BB.
Watch my Vimeo Video of these four KWC and Cybergun Model 1911 4.5mm Steel BB and Airsoft CO2 Blowback Pistols:
Trigger Pull: The trigger pull on the Cybergun Sig Sauer P226 Airsoft Replica is good in both single and double action. Once the slide is pulled back and released the first round is chambered and the hammer will remain back placing the P226 in single action mode, the pull is light and the take-up is fairly short, most of your shots will be in single action mode unless you use the de-cocker to lower the hammer for a subsequent double action next shot, double action shots are still pretty light but much longer in order to cock the hammer.
Accuracy: Shooting the Cybergun Sig P226 from 20 feet out in semi rested position I was able to get very good results. I placed 10 rounds in about 1.5 inches with the shot placement being a bit low possibly due to my barrel mod, adjusting the hop-up may bring the aim point back up to where it should be. The Sig Sauer P226 Airsoft Replica shot right around the 316 fps range while conducting my 5 shot average chrony testing which was lower than advertised but I was using much heavier .20 gram BB's. You can expect to get a full magazine worth of shots out of each gas fill-up but I did notice that as the magazine got colder it did tend to become much less efficient and also seemed to vent a lot of vapor.
Build Quality: The build quality is generally good and I was surprised at the finish on this model as the paint is not showing any wear marks so far, the fit is good with minimal slide and barrel wobble and everything is working very well with no problems so far with a fair amount of shots through it, guess you could say I like shooting this gun :) Most of the gun is metal with only the grips and a couple internal parts being plastic.
Realism: The Cybergun Sig Sauer P226 6mm Airsoft pistol is a replica of the real steel Sig Sauer P226 right down to the licensing and it really is a great looking and functioning Airsoft Replica. You can field strip this gun exactly like a real Sig and all the mechanical parts work just the same including a working de-cocker and adjustable front sight.
Seemed to shoot a bit low for me, could adjust with hop-up a bit?
Only one magazine per Gas fill.
Comments:
I am a big Sig Sauer fan so it would take a lot for me to not give this gun a good review, with that said it performed pretty well, sure it was not the most powerful but I was using gas over CO2 so I was not expecting too much, it also shot a bit low for me but again that may have been because of the barrel mod so who really knows for sure at this point ;) And yes it came with that unsightly orange tip that I took short work of removing. At teh end of the day I still love it and it performed well without letting me down, just like a would expect from a real Sig Sauer!
My Vimeo Table Top Review of the Cybergun Sig Sauer P226 GBB Blowback Airsoft Pistol:
I usually do my Table Top Video Review first but this time around I did my Field Test Video Review first since I was all setup checking out a couple other guns at the time. When I do my detailed Table Top Video Review for the Cybgergun Sig Suer P226, I'll post the link here so stay tuned. If you have not already checked out my Barrel Mod Video for this same gun then check that video out where I remover the extended orange portion of the metal barrel and make the barrel flush with the end of the slide which is how the real steel version was originally made.
Getting back to the Cybergun Sig Sauer P226 GBB blowback Airsoft Pistol field test, as per usual I test this Airsoft semi auto gas blowback pistol on the Chronograph to see what kind of real world velocity I get and since I had some Green Gas on hand, I used it for this part of the review and got an average of 315 fps with a six shot string.
I also stepped back 20 feet and shot 10 times at my stationary target using a semi rested position (sand bag up front and kneeling in the back). Even though the Sig Sauer P226 shot a bit low I did get about a 1.25 inch group with the exception of one flyer that hooked down just a bit making the 10 shot group a bit wider at just under 2 inches. The low shot placement may have been caused by my barrel mod but since I did not do a before and after test, I can not say for sure?
Make sure to watch my YouTube Video of this Field Test as it also includes some nice slow-motion of the slide blowback at both 400 and 1200 frames per second.
Watch my full Video Field Test Shooting Vimeo Video below:
My 5 shot Chronograph test resulted in a lower than expected 308 average fps while my accuracy test shot from 20 feet out in a semi rested position this time received a just over 2 inch group but with most shots being within 1 inch, I have found with Airsoft guns that there can be some floaters perhaps due to inconsistencies with some of the ammo. In terms of shot placement the KJWORKS KP-05 HI-CAPA 1911 shot very well centered only being just slightly high and to the left but only marginally. I was also able to get 2 full magazines plus another half mag this time around so just over 60 shots with the KP-05.
KJWorks KP-05 1911 HI-CAPA Airsoft Pistol although not shooting as hard as I though it would still performed great for me and would make a great field gun as it performs very well and has a nice high capacity magazine which would come in handy in the heat of battle.
My 5 shot Chronograph test resulted in a very respectable 366 average fps while my accuracy test shot from 20 feet out in a semi rested position this time around came in a bit higher than my pre test right at around 2 inches. Several of the shots hit right on top of each other. In terms of shot placement the KJWorks KP-09 CZ 75 shot fairly well centered but just a bit high and a tad to the left. I was also able to again get 3 full magazines or around 75 shots out of this heavy blowback Airsoft pistol.
KJWorks KP-09 CZ 75 Airsoft Pistol really has a lot going for it, it's a great Replica of a real steel CZ 75 with a very nice single action trigger, it has great snappy full blowback with excellent fps and accuracy and it even gets a solid 75 shots out of a single CO2 which is very good for this style of full blowback gun.
I have not done my official Table Top and Shooting Reviews for the Gas Blowback Airsoft Cybergun Sig Sauer P226 but I really wanted to cut off the ugly orange painted barrel tip, it was kind of driving me crazy! keep in mind here in Canada we are not required to have orange tips on our Airsoft guns, most of the all metal or all black Airsoft guns imported these days fall into the "airgun uncontrolled firearms" category. If you live in the US or other parts of the world you could be breaking the law if you do this mod so be warned...
Your best best is to simply watch my Vimeo Video as I show you exactly how I removed the orange painted portion of the metal barrel using a hack saw, file, vice and some sand paper. All in all it was not too difficult and only took about 15 minutes to complete...
Trigger Pull: The trigger pull on the KJWORKS KP-05 is what you would expect from a true 1911 single action only trigger, it has very little take up with a smooth crisp and light release to it.
Accuracy: I shot the KJWORKS KP-05 from 20 feet out in semi rested position and got very good test results. I was able to place 10 rounds in under 1.5 inches and getting four shots right in the bullseye making the shot placement very good even without adjusting the sights (which can be adjusted for windage). The KJWORKS HP-05 1911 styled HI-CAPA Airsoft Replica shot right around 300 fps range while conducting my 5 shot average chrony testing which was surprisingly low for the CO2 magazine version, this may have been a temperature or CO2 related condition, when I conduct my full Field Test Shooting Review, I will review this and see if we can do better? I also got two full 30 round magazines worth of shots which is what you would expect from this style of full heavy blowback airsoft pistol.
Build Quality: I am extremely impressed with the build quality of all the KJWORKS Airsoft guns so far, the fit and finish is the best around on any of my guns including my 4.5mm steel BB shooters. After shooting several magazines worth of BB's, areas that are painted like the metal friction areas show very light wear which is rarely the case with metal built blowback airguns. Again the tolerances between the moving parts like the slide and frame are very tight showing excellent workmanship and machining from KJWORKS.
Realism: The KJWORKS KP-05 6mm Airsoft pistol is a replica of a High Capacity styled tactical 1911 45 Auto and is a great looking and functioning replica. You will not find any actual licensing on this pistol and the CO2 magazine does stick out a bit to accommodate the 12 gram CO2 but other than that this Airsoft pistol looks and works near exactly like a real 1911 tactical semi auto and is fully field strip-able. I really like the updated more tactical add ons like the tactical rail, machined trigger and hammer, white dot adjustable sights, wrap around grips and ambidextrous safety.
All metal pistol with good overall realistic weight to it.
Full heavy blowback operation.
Typical KJWORKS excellent fit and finish.
High capacity magazine 30 rounds.
Very good accuracy and well centered on target.
Nice replica of a High Capacity Tactical 1911 styled pistol.
I like the stainless highlights and ambidextrous safety and Rail for accessories.
Fully field strip-able.
Cons:
Shot a bit low Feet Per Second for me - should do better?
CO2 magazine is long to accommodate the 12 gram CO2.
Slide is heavy enough but seems to be a bit sluggish which is kind of a 1911 trademark so that can be taken as good or bad.
Comments:
The KJWORKS KP-05 1911HI-CAPA is another excellent full blowback Airsoft pistol from KJWORKS. The HP-05 is a classic upgraded more modernized version of the 1911 semi auto pistol which is a great foundation to build any pistol from. I found the CO2 usage to be decent on the KP-05 but felt that I should have been able to get more fps out of this pistol, I will be testing the KJWORKS KP-05 again and hope to see some better results in this area. With that aside, the KP-05 1911 HI-CAPA is a great shooter and as is, with its high capacity magazine would be a perfect sidearm for any Airsoft related squirmish or even just for honing up your shooting skills when getting to the gun range is not an option.
Trigger Pull: The trigger pull on the KJWORKS KP-09 CZ 75 Airsoft Replica is surprisingly light in single action but incredibly sticky at first in double action, with that said you really will not be shooting very often in double action unless you happen to de-cock the gun for some reason, at least you have the ability to shoot with the hammer down in double action when required. In signal action it took me a bit to get used to the very light trigger pull as I was letting some shots go off early.
Accuracy: I shot the KJWORKS KP-09 from 20 feet out in semi rested position and got very satisfactory results. I was able to place 10 rounds under 2 inches almost getting a 1 inch group with the exception of one flyer. Shot placement was also well centered but just a bit high which could easily be corrected by adjusting my aim point just a bit down. The KJWORKS CZ 75 Airsoft Replica shot right around the 360 fps range while conducting my 5 shot average chrony testing which is right where this gun is supposed to be. I also got three full 24 round magazines worth of shots with a bit of CO2 left over for a partial mag, so this gun can easily get 75 shots out of a 12 gram CO2 - not bad at all for this style of full heavy blowback airsoft design.
Build Quality: I am extremely impressed with the build quality of pretty much all the KJWORKS Airsoft guns, the fit and finish is the best I have seen on any of my guns including my 4.5mm steel BB shooters. Even after shooting several magazines worth of BB's, the painted metal friction areas show very light wear which is not always the case with metal built blowback airguns. (there was some wear present within the ejection port but this is common even with real steel guns as metal on metal will wear down the finish). The tolerances between the moving parts like the slide and frame are very tight showing excellent workmanship and machining.
Realism: The KJWORKS KP-09 6mm Airsoft pistol is a replica of the real steel CZ 75 and is a great looking and functioning copy. You will not find actual licensing on this version and the CO2 magazine does stick out a bit to accommodate the 12 gram CO2 but other than that this Airsoft pistol looks and works near exactly like the real mccoy and is full field strip-able. Even the safety operates just the same with safety available on half cock and full cock only.
All metal pistol with good overall realistic weight to it.
Very crisp and firm full blowback operation.
Excellent fit and finish - best I have seen.
Excellent fps and CO2 efficiency (three plus full 24 round magazines)
Good accuracy and well centered on target.
Very believable working replica of the real steel CZ 75.
Fully field strip-able.
Cons:
Does not have official CZ 75 licensing.
CO2 magazine is long to accommodate the 12 gram CO2.
Did get some finish wear in the ejection port area.
Comments:
The KP-09 CZ 75 is another wonderful full blowback Airsoft pistol from KJWORKS. The CZ 75 is a classic semi auto pistol and deserves the attention to detail the KJWORKS version demonstrates. I found the CO2 usage to be very good on the KP-09 considering the rather high 360+ fps I was abel to get with it. Top this off with high marks in the accuracy department and you have a real winner here. So if you're looking for a quality Airsoft Replica of the classic CZ 75 that shoots straight and hard and looks and operates just like the real steel version then the KJWORKS KP-09 should just do the trick for you.
Here's a heads up on some new items we will be adding to the Canada Replica Airguns Store very soon so keep checking back if you're interested in them!
Your best bet is to Watch My Vimeo Video as I go over them all and show you around the new products, but for now here is some basic info on each item:
I am happy to report back to you on all the new cool stuff I got to see at this years 2013 SHOT Show in Las Vegas. Make sure to also watch my Vimeo video at the bottom of this post for some first person styled play by play of my experience at the Vegas SHOT Show 2013. (like you're there with me ;)
First up I want to cover a new gun from ASG, I have been wanting to get my hands on the 4.5mm Bersa BP9CC and I finally got to, not only did I get my hands on it but ASG was kind enough to supply me with one to take home for review. You can get the Bersa BP9CC in both Blowback and non-blowback versions and also in either BB or Airsoft. I opted for the 4.5mm BB Blowback version. I will be reviewing this BB gun very soon!
ASG also had a very cool prototype of an Airsoft CZ Scorpion EVO 3A1 hopefully coming out soon.
While roaming around SHOT Show 2013, I came across an interesting booth from FlashFog Security. I often get people asking me about using an airgun as a home defense weapon and I strongly advise against this. If the intruder is not scared off by the gun there is little an airgun can do to actually stop them. The FlashFog system works by rapidly filling a room with dense fog combined with a strobe light effect which blinds and disorients intruders completely. There is little an intruder can do other then try and get the heck out of there!
UPDATE: FlashFog just added a new section to their website specifically for School Security to help keep our schools safer from potential safety threats! So check it out: School Security Smoke Screen
I was a bit surprised by Gamo this year, they tend to stay away from actual Replica's and generally make BB/Pellet guns that look like popular guns but not any gun in particular. Gamo has a new BB/Pellet MP9 based machine pistol that uses a similar mechanism to their P-25 and PT-85 so it can shoot both 4.5mm BB's and .177 caliber Pellets using a double ended 16 shot rotary magazine. It also has an internal blowback system so it should have some recoil feel to it! I am pretty sure it is semi auto only but still a nice addition to their lineup!
Gamo also brought out a new 4.5mm BB Blowback pistol called the C-15 which has a metal slide and plastic frame, it kind of reminds me of the Umarex HPP in how it looks and feels.
Umarex had several new products that I am sure everyone is going to like! One that I think will do really well is the Steel Force, the Steel Force is designed around the 4.5mm BB shooting Steel Storm platform so it has a 6 round burst blowback operation and holds the 2x12 gram CO2 in the magazine while the BB's go in a 300 round hopper that feeds into a 30 round spring fed internal magazine. Like the Steel Storm it will shoot around 430 fps. The Steel Force has the advantage of being styled after the AR platform so it has a collapsible stock which will make shooting very easy.
Another often asked for airgun replica is the historic German Luger. This year Umarex stepped up to the plate and introduced the Umarex P.08 4.5mm BB pistol. Sorry, no blowback or even a working slide on this one but it is all metal and has a very good weight and feel to it.
If you're a fan of the entry level Umarex XBG then you may be interested in the new Umarex T.D.P. 45 which is very similar to the XBG in looks and features but with a slightly different look to it.
If you've ever wanted to turn your pistol into more of a PDW styled gun, you may be able to depending on which Umarex gun you have? Umarex added a very cool accessory called the T.A.C Converter that converts your Umarex HK USP (BB-Airsoft), SW MP40 (BB), XBG (BB), CZ Enforcer (Airsoft) and Walther P99 DOA (Airsoft) into more of a tactical (PDW) or Personal Defense Weapon complete with for-grip, adjustable rear sight, lots of rail options and a foldable stock.
I am assuming the Crosman M4-177 Pellet/BB Rifle has been doing well for Crosman as they have expanded with some more similar assault styled air rifles. The Crosman MSR77NP pretty much looks like a classic M16 but is in fact a Nitro Piston break barrel pellet rifle able to shoot .177 caliber pellets at 1200 fps (I hope there is a 499 fps Canada version planned too?).
A new takeoff of the M4-177 is the MK-177 which also shoots .177 caliber pellets and 4.5mm BB's using a multi-Pump System but it uses an upgraded more efficient pump system that squeaks out more fps with less pumps. The Crosman MK-177 is designed after the FN SCAR and is available in an adjustable iron sight version or a Red Dot equipped kit version.
One thing you can never get enough of in my opinion is another 1911 pistol! Crosman is introducing their GI Model 1911BB Blowback 4.5mm CO2 pistol, the one they had on hand was more of a prototype so the slide was not operational but it will feature an all metal design, blowback operation, 450 fps and a 20 round drop out magazine. I am sorry to say but it looks like the Crosman C51 has been dropped from Crosman's lineup but if you want a similar styled gun you can checkout the KWC SW40F which is a very close airsoft version.
We recently started carrying G&G Armament Airsoft guns, you can checkout my review of the Xtreme 45. I did stop by their booth and they had some new products on display, the M1 Grand (all wood stock) Airsoft had it's magwell all wrapped up as G&G had a propriety magazine system they did not want their competition to see. G&G also had some very interesting targets that light up, when shot they would react by individually turning off so you could see if you hit it or not.
There was a rather large crowd at the KWA booth but it was a shared booth so it's hard to say what everyone was looking at, the KWA area was pretty full, I did talk to the KWA rep and asked him point blank if KWC and KWA where the same or sister companies and the answer was not at all. There are often a lot of guns that look like they could be from the same company, I guess there is a lot of copying going on ;) One gun from KWA I would love to get my hands on is the Kriss SMG!
Now keep in mind many of these guns I have highlighted today are not available yet and a lot of them should be coming out in the spring time frame so please try to refrain from repeatedly asking when I will review them and have them in the store, it takes time and as much as we all want them now, they get here when they get here!
Watch my Vimeo video of the Replica Aiguns at SHOT Show Vegas 2013
I've already done a KJWORKS review on the KP-02, KP-07 and Elite 1A and they turned out to be very high quality Airsoft pistols so the extra price does get you a higher quality gun. So in this preview we are simply looking at some more models that from the looks of things I expect to be more of the same in terms of high quality and excellent functionality.
The KJWorks models we are looking at today are the KP-05 (1911 HI-CAPA), the KP-09 (CZ 75) and the M9 (Beretta M9). Even though none of them are licensed, they are very detailed and realistic copies of the original real steel versions with full blowback operation, heavy metal drop out magazines and lots of metal throughout. You would be hard pressed to tell them apart from the real powder versions.
All version in this preview load CO2 in the magazine along with 6mm Plastic Airsoft BB's, none of them have any orange markings or translucent parts as they fall into the uncontrolled firearms category here in Canada.
I look forward to doing my full review of these three very nice KJWorks Airsoft pistols.
Buy the B&W Dragunova SVD in the Canada Store - Buy Airsoft Rifles in the US Store
