If you have been watching my Full Auto Fun Videos, then you will have noticed that I have recently been using Clay Pigeons as my go-to targets. Generally Clay Pigeons are shot from launchers and used with shotguns since the flight of the Clay Pigeon simulates a bird in flight nicely.

So I thought, why not use them as reactive targets for my Airguns and Airsoft guns? It turns out they work pretty darn good, well at least with 4.5mm Steel BB pistols and I would imagine even better with pellet guns. What about Airsoft guns, will the Airsoft lighter weight plastic BB's have enough mass to get the job done?

You'll have to watch this video to find out the answer to that question when I unload a full magazine of .20 gram Airsoft BB's into some Clay Pigeons using my KWC .50 Desert Eagle...

Buy KWC Airsoft Desert Eagle in Canada

Buy KWC Silver Desert Eagle in Canada 

This Article and Video expresses my views and opinions on this matter and should not be taken as legal advice.

Main points covered:

• Uncontrolled Firearms do not require a Firearms License within Canada to own and operate.

• What is an Uncontrolled Airgun and Airsoft Gun?

• What is an Uncontrolled Blank Gun / Starter Pistols?

• What about Fully Automatic Airguns and Airsoft Guns?

• What about Replica Guns?

NOTE: Controlled Firearms require a POL (Possession Only License) , PAL (Possession Acquisition License) or R-PAL (Restricted Possession Acquisition License) within Canada to own and operate. 

MEMORANDUM D19-13-2

Firearm – a barreled weapon from which any shot, bullet, or other projectile can be discharged and that is capable of causing serious bodily injury or death to a person, and includes any frame or receiver of such a barreled weapon and anything that can be adapted for use as a firearm.

“Uncontrolled”firearms are those devices that, although falling within the definition of a firearm in the Criminal Code, are exempt from specific legal requirements of the Firearms Act and its regulations, as well as from other legislative provisions. “Uncontrolled” firearms should not be subdivided into any of the non-restricted, restricted, or prohibited classes. The following types of firearms are deemed “uncontrolled”:

Flare, blank, rivet and industrial guns: Any device that is designed exclusively for signaling, for notifying of distress, or for firing blank cartridges or for firing stud cartridges, explosive-driven rivets or other industrial projectiles, provided that the importer intends to use it only for the purpose for which it is designed.

NOTE: (Toy guns and starter pistols do not generally qualify as firearms. However, some toy or model guns and starter pistols may be designed with very realistic mechanisms or appearances (e.g., color, size, scale, translucency) and resembling a real make and model of a firearm. In such cases, they may be considered replica firearms even if they are made of plastic, die cast zinc, or other material.)

Low muzzle velocity/energy guns: Any barreled weapon that is not designed or adapted to discharge projectiles at a muzzle velocity exceeding 152.4 meters per second (500 feet per second) and at a muzzle energy exceeding 5.7 Joules, or to discharge projectiles that are designed or adapted to attain a velocity exceeding 152.4 meters per second (500 feet per second) and an energy exceeding 5.7 Joules. Both thresholds of 152.4 mps and 5.7 Joules must be exceeded for the firearm to be considered “controlled”. This requirement exempts firearms that fire below the threshold velocity with a standard projectile, but exceed the threshold velocity when fired with a high-velocity projectile. 

Airsoft guns and certain types of paintball guns or markers may qualify as a replica firearm, if the muzzle velocity of the projectile does not cause serious bodily harm and their external features are clearly designed to resemble a specific and readily identifiable make and model of a firearm. To be considered a firearm, within the meaning of the Criminal Code, an airsoft gun must have a muzzle velocity in excess of 111.6 meters per second (366 feet per second).

NOTE: This memorandum used to state when using a .20 gram BB but does not specify this BB weight anymore?

NOTE: The term air gun is a colloquial term referring to BB or pellet guns. Such guns operate either as spring- powered, gas-powered, or electrically powered. If the muzzle velocity of the air gun is less than 152.4 mps (500 fps)/5.7 joules but still able to cause serious bodily injury to a person, it may be considered an “uncontrolled” firearm. Airsoft guns and certain types of paintball guns may qualify as a replica firearm (see paragraph 49 of this memorandum).

Replica firearms:

“Replica firearm” is defined as any device that is designed or intended to exactly resemble, or to resemble with near precision, a firearm, and that itself is not a firearm, but does not include any such device that is designed or intended to exactly resemble, or to resemble with near precision, an antique firearm.

For a device to be a replica firearm it must meet all three requirements:

• (a) it cannot be a firearm, meaning it does not discharge a projectile with sufficient energy to cause serious bodily injury or death to a person. If the device is a firearm, then it cannot be a replica firearm (and vice versa);

• (b) it must resemble exactly, or with near precision, a real existing firearm of an identifiable make and model. With respect to visual examination, note that the maximum observing distance is one at which the equivalent make and model of the firearm can be identified. This distance will vary from one firearm make to the next. For example: A Luger pistol has a very distinctive silhouette as compared to other makes and is therefore more readily identified from further away. The examination of the object is something more than casual, but less than detailed. The device does not need to be so close that markings are identifiable; and

• (c) it cannot be designed or intended to exactly resemble, or to resemble with near precision, an antique firearm. 

RCMP Website "Air Guns"

1. Air guns that are "Controlled" Firearms for purposes of both the Firearms Act and the Criminal Code

These are air guns with both a high muzzle velocity (greater than 152.4 meters or 500 feet per second) and a high muzzle energy (greater than 5.7 joules or 4.2 foot-pounds). The "muzzle velocity" is the speed of a projectile at the instant it leaves the muzzle of a gun, normally expressed in meters per second or feet per second. The "muzzle energy" is the energy of a projectile at the instant it leaves the muzzle of a gun, expressed in joules or foot-pounds. Air guns need to meet both standards to be classified as "Controlled" firearms for purposes of the Firearms Act.

These high-powered air guns are subject to the same license and registration requirements as a conventional "Controlled" firearm. Owners and users are also required to store, transport, display and handle them safely in accordance with the regulations supporting the Firearms Act.

Usually, the manufacturer's specifications are used to determine what muzzle velocity and muzzle energy an air gun was designed to have. This information may be available in the user's manual or on the manufacturer's website. If the information is not available, individuals can call the Royal Canadian Mounted Police Canadian Firearms Program (CFP) at 1-800-731-4000 and ask to speak to a firearm technician to find out if the air gun is considered to be a firearm for purposes of the Firearms Act.

High-powered air rifles are generally classified as non-restricted firearms. However, the classification depends on the exact design of the air gun. Air rifles manufactured to resemble an assault rifle could be non-restricted, restricted or prohibited depending on the exact model imitated. High-powered air rifles would also be prohibited firearms if fully automatic or if they have a sawed-off barrel. They could also be restricted firearms if they have a folding stock that reduces the overall length to less than 660mm. 

Additional thought on this subject: Even though Uncontrolled Firearms are not governed by the same laws that apply to Controlled Firearms within the Firearms act and do not need to be handled or stored similar in the same way you are required to handle, transport and store a Controlled Firearm, we need to treat our Uncontrolled Airguns, Airsoft Guns and Blank guns with care and go over and above what is expected when had handle, transport and store them.

Perhaps the last of my 4.5mm Steel BB Dull Auto Fun Video? We'll see? Today I take out my Umarex EBOS (Electric Burst of Steel) 8 Round Burst BB Machine Gun and again take aim at a bunch of clay pigeons I set up 30 feet away. Even thought the EBOS does not have the highest rate of fire with only 500 rounds per minute, it does get the job done because it stays true on target and really proved to be very accurate allowing me to even trim off the smallest bits of clay pigeon stuck in the edges of the holders.

The rate of fire on the Umarex E.B.O.S. almost reminds me of what you would hear or expect from an AK 47 type machine gun.

Near the end of this video I try my luck at shooting some of the clay pigeons out of the air shotgun style but failed horribly :( Perhaps I should give by modified 1200 rounds per minute Drozd Blackbird a go at it :)

Buy BB guns in Canada  

Buy BB guns in the US

Only a few more Full Auto Fun Videos left to do for you, todays features the Umarex Steel Force which is basically an updated version of the Steel Storm but instead of having an H&K styled outer shell, the Steel Force is based around the popular AR 15 series and like many modern AR 15's, the Steel Force has an adjustable stock which really helps with target acquisition and accuracy.

Like my other Full Auto Fun Videos, I take out a bunch of clay pigeons from about 30 feet away. The Umarex Steel Force proves to be very accurate and CO2 efficient (got about 300 shots from the pair of 12 gram CO2's) but is a bit of a pain to reload the spring fed 30 rounds magazine when the 300 round BB hopper is full.

All in all if you'er looking for a low cost and super fun BB machine gun with a high rate of fire, good CO2 efficiency, awesome pinpoint accuracy and pretty decent power, then pick yourself up one of our Umarex Steel Force BB Guns!

Buy the Umarex Steel Force in Canada

Buy the Umarex Steel Force in the US

Alright, so todays Full Auto Fun Video may be stretching things just a bit but I figured that since my Umarex Walther SG 9000 does have the ability to shoot 3 rounds with each pull of the trigger that we'll give it the benefit of the doubt and include it in this round of Full Auto Fun Videos.

The Walther SG 9000 is a kind of different looking airgun, the back half looks like a Walther Pistol while the front half is more of a tactical styled shotgun. And like a shotgun you can shoot multiple BB's with one shot. You actually have teh option of shooting single shot or three shot burst. In single shot mode, the Walther SG 9000 is pretty peppy shooting at around 500 fps on a fresh and warm 88 gram CO2. When you switch the SG 9000 over to three shot burst mode, it does slowdown somewhat closer to the 250 fps range so not really that great for any serious penetration.

But I figured since I was shooting clay pigeons which are made for shotgun use, why not use a BB styled multi-round shotgun on some of them! All in all the Umarex Walther SG 9000 got the job done...

I am sad to say that Umarex does not seem to make the Walther SG 9000 anymore so if you're looking for one you may have to settle for a used on if you can find an owner willing to give it up.

Buy BB Rifles in Canada 

Buy BB Rifles in the US

Hey everyone, we just got a really large Umarex order in our Canada location so if you have been waiting on some product from Umarex we should have most items in stock now...

Some of the more popular Umarex items these days are:

• Umarex Steel Force 6 Round Burst CO2 BB Rifle
• Umarex Steel Storm 6 Round Burst CO2 BB Gun
• Umarex H&K MP5K-PDW CO2 BB Rifle
• Beretta PX4 Storm CO2 Blowback Pellet / BB Pistol
• Desert Eagle Black Magnum Research CO2 Blowback Pellet Pistol
• Umarex Browning Buck Mark URX .177 Break Barrel Pellet Pistol
• Beretta FS M84 Blowback CO2 BB Pistol
• Colt Python 6 Inch CO2 Steel BB Revolver
• Colt Commander 1911 Blowback CO2 BB Pistol
• Umarex Legends Luger P08 CO2 BB Pistol
• Walther PPS CO2 Blowback BB Pistol
• Umarex Legends C96 Blowback CO2 BB Pistol
• Legends Makarov Ultra Blowback CO2 BB Pistol
• Umarex HPP Blowback CO2 BB Pistol
• Umarex Walther P38 Blowback CO2 BB Pistol
• Walther CP99 Compact Black Blowback CO2 BB Pistol
• Walther PPK CO2 BB Blowback Pistol 

Full Auto Fun video number three this week and this one is perhaps the craziest one! When you take a Drozd Blackbird that already has a 800-1000 round BB magazine, convert it to 1200 rounds of full auto, add a custom JimC Barrel to it, some bulk CO2 and a bunch of other cosmetic accessories... Well you get the most ridiculous full auto BB gun you can ask for.

Since I had an extra 800-900 BB's more than I am used to when making these full auto videos, I decided to add a few additional targets over and above the clay pigeons I have been using so far. I picked up a nice fairly heavy gauge Santa tin and a rather solid hard wax candle from the dollar store that proved to add some drama to this Full Auto Fun video!

Make sure to also watch my first two Full Auto Fun videos:

• KWC CYBERGUN MINI UZI 4.5MM STEEL BB MODIFIED FULL AUTO FUN

• RAP4 RAP5 MP5 4.5MM STEEL BB MODIFIED FULL AUTO FUN

If you like what you see in this video and want an absolutely crazy BB gun, then checkout our Replica Airguns Store where we Sell the Drozd BB gun and some add ons for it!

Buy the Drozd BB Guns in the Canada Store

Video number two in a summertime series I'm calling "Full Auto Fun". My first video featured the KWC/Cybergun CO2 BB Blowback Mini UZI. The KWC Mini UZI has lots of kick and is a bit hard to figure out where exactly the sweet spot is but once you find it, it really tares up the targets in full auto mode!

In this "Full Auto Fun" video I bring out my RAP4 - RAP5 MP5 Full auto BB Rifle. The RAP5 MP5 started out life as a .43 caliber paintball gun but I bought it converted in the factory to 4.5mm Steel BB. RAP4 converts it by adding a barrel sleeve adaptor and includes some plastic casings that allow you to place 4.5mm Steel BB's into a kind of donut shaped shell that is then placed into the 21 round magazines. The plastic Donut BB shells eject from the gun like a real shell casing which is super cool!

Like my KWC Mini UZI Full Auto Fun video, I shoot up a bunch of clay pigeons but this time using my RAP4 - RAP5 MP5 4.5mm Steel BB Full Auto Rifle which I found to be very accurate but perhaps a bit thirsty when it comes to CO2 usage. Some bulk air would be a nice combination with this BB shooter, maybe in another video...

Buy Full Auto BB Guns in the Canada Store

Buy Full Auto BB Guns in the US Store

I had so much fun getting my modded Drozd Classic Full Auto BB Gun out the other day and shooting it, that I thought I would make some more Full Auto videos for you! So this upcoming week I will be taking a look at some of the following BB guns:

• Full Auto Modded Umarex Walther PPK

• Full Auto Modded Cybergun GSG 92

• Full Auto Modded Cybergun UZI

• Full Auto TYREX PPA-K01

• Full Auto Burst Umarex Steel Strom

• Full Auto RAP5 MP5

Stay tuned... Not sure exactly what I am going to do in terms of shooting tests and comparissons but I do know it will be fun :)

Buy Full Auto BB Guns in Our Store in Canada

Buy Full Auto BB Guns in Our Store in the US

This topic of Blowback Airguns Versus Non-blowback Airguns comes up often so I thought I would address it a second time around since I get a lot of new visitors and subscribers daily who may not have watched my first video explanation on this topic. You can also checkout my first video on this subject since there may be some stuff I missed out in this video second video ;)

There are really two types of people asking or commenting on Blowback Airguns Versus Non-blowback Airguns. The first type of person who genuinely wants to know which is best and for what reasons. Then there is the other kind of person who makes a narrow minded statement that one type is clearly better than the other type, based on their own preferences and interests but not considering that there are other people out there with different opinions and preferences than them. You know who you are and we all know you are not going to change cause that would require an open mind...

Here is a list of the Pros and Cons I go over for each style of Airgun:

Pros:

• Blowback guns simulate recoil.

• Blowback guns can have better and more true triggers compared to their real steel counterparts.

• Blowback guns can be better suited for action shooting.

• Blowback guns are better as prop guns.

• Blowback guns are generally more realistic in terms of mechanics.

• Non-blowback guns generally use less CO2 per shot.

• Non-blowback guns generally have higher fps.

• Non-blowback guns can be more accurate.

• Non-blowback guns can be more reliable.

• Non-blowback guns can be less expensive.

Cons:

• Blowback guns generally get less shots per CO2.

• Blowback guns generally have lower fps.

• Blowback guns can be less accurate.

• Blowback guns can be less reliable.

• Blowback guns can be more costly. 

• Non-blowback guns do not simulate recoil.

• Non-blowback guns do not have true single action only triggers.

• Non-blowback guns generally have heavier triggers that slow down shooting performance.

• Non-blowback guns are generally not as good for prop use and or training.

• Non-blowback guns generally are not as realistic compared to their real steel counterparts. 

Watch my Vimeo video where I go into detail on Blowback Airguns Versus Non-blowback Airguns again ;)

A very common occurrence with CO2 Airguns and Airsoft guns are leaky CO2 seals. Usually this occurs right where the CO2 cartridge connects to the main valve area. This can be either in the gun or in the magazine depending on the setup of the airgun.

There are many reasons why this can happen, but the most common reasons are a worn-out or dried up seals or even a seal that has been imprinted or misshapen from the constant pressure of the tip of the CO2 pressing against it.

When this happens you may encounter a leaking CO2, the severity of the leak can vary from mild slow leaks to leaks that can be so bad that the gun is unusable. Keep in mind there can be other problems not related to the CO2 seal such as in the valve area, the fix I show you in this YouTube video will not fix a leaking valve, you can try using something like Crosman Pellgun oil for a problem like that.

Watch my below Vimeo video where I show you how you can easily use some Plumbers Teflon Tape to improve the contact points between your CO2 and CO2 main seal and eliminate leaking CO2 in your Airgun.

A very common question I get asked is "How Long Can I Leave CO2 in My Airgun?" So what do I do when I get asked a question over and over again... Well I make a video and give you my answer to the question.

Some CO2 Related Questions I seem to get over and over again are:

1. Can I leave an unused CO2 in my Airgun and for how long is it safe?

2. Can I reuse a C2 once it is empty?

3. Can I use my gun without CO2?

In this YouTube video I address questions 1 and 2, I kind of forgot about question number 3 since it is not as often but it does come up from time to time believe it or not and the answer to being able to use a CO2 airgunwith out CO2 is "NO", It's kind of like trying to drive a car without gas, or turn on a light without electricity or stay alive without food...

So anyways, watch my below Vimeo video for answers to questions one and two:

This may be a bit controversial for some people who don't like the thought of using an gun for hunting or extermination of unwanted pests. But weather or not it is accepted by all, it is a practice that many people still embrace including myself when done in a humane way.

Let's start off by addressing this topic by asking some questions and filling in some of the answers. Keep in mind I go into much more detail in my Vimeo video below.

What is the reason that you need to Shoot or Hunt an Animal?

Are you shooting an animal out of need or just for fun, sure there is a thrill in the sport of hunting but after taking down your prey, the animal should not be killed in vain as the meat should be eaten. There are also times when pesky critters get into your gardens, tree farms, feeding stations garbages and who knows what else? I personally think shooting an animal that has not done you any harm or that you don't plan on eating is not ethical. So question your motives wisely?

Can you use an Airgun for Hunting and or Pest Control?

The short answer is yes! As long as you choose the correct Airgun for the job, one that has enough power and accuracy to get the job done in a humane manner. Using an underpowered or inaccurate gun of any type for the chosen target will lead to the animal being wounded and possibly getting away to suffer unnecessarily.

What about Pistols versus Rifles?

Given the choice, a rifle will always be your best bet, rifles tend to be more accurate since they are more stable to hold and the fact that the sights are further apart which improves the guns accuracy. Most rifles also allow for enhanced sighting systems like red dots or magnified scopes for even further accuracy improvements. There are some pistols made specifically for hunting and target shooting that can be accurate but I would limit their use to shorter ranges.

What about Pellet guns versus BB guns?

BB guns in general are not meant for hunting or pest control, and in most cases they are underpowered and not as accurate as their pellet shooting counterparts, especially out at longer ranges where most pests keep their distances to. If you plan on doing some hunting and or pest control, please invest in an adequate pellet rifle to get the job done humanly.

What type of Ammo is best for Hunting and Pest Control?

There are lots of types of pellets available, pointed, rounded, flat, hollow-point and even pellets that have nylon tips. At the end of the day, use the pellet that is the most accurate in your Airgun because shot placement will win over pellet shape any day of the week. The reality is that as long as that pellet hits the target with adequate velocity, it doesn't matter what shape it is, it's more than likely going to pass right through the animal.

What is the lowest FPS that I can use?

I would rather ask the question, what is the highest fps I can get away with since more fps will give you more margin for error, since it will have a flatter trajectory and will do more damage even if your shot is off a bit. An experienced shooter could make a kill shot on a small pest even with a 400 fps airgun but the shot would have to be perfect and the range would have to be close. Of course when shooting larger game, you will need larger caliber pellets with higher velocities. Also when using a high velocity airgun you need to consider what is beyond your target, if you miss, where is that pellet or bullet going to end up? You need to make sure you do not injure anyone by mistake as pellets/bullets can travel a long distance.

How large of an Animal can an Airguns Kill?

This is really dependent on the Airgun being used, Airguns come in many different calibers, from .177 right up to .50 caliber, some PCP Airguns can even take down a deer! You need to do your research and make sure the Airgun you choose has both the power and accuracy you need for the intend prey.

Where can I use an Airgun for Hunting and or Pest Control?

This is a question you need to ask your local authorities as laws and hunting regulations are different just about everywhere. Even shooting pests on your property may require a permit so be careful to obey your local laws.

In this Comparison Video I go through the benefits and shortcomings of CO2, Spring Piston and Pump Airguns. I focus mainly on Airguns but there is a bit of a crossover with Airsoft guns.

All three systems (CO2, Spring, Pump) create pressure that forces the ammunition with a high force out of the barrel. Similar to how gun powder is the source of energy for a bullet.

Here are some basic statements that best describe CO2, Spring Piston and Pump Airguns.

CO2 Airguns:

• CO2 Airguns use the expansion of CO2 gas to create the pressure required for the ammo.

• CO2 Airguns generally store enough CO2 for multiple shots per cartridge.

• CO2 Airguns have a limit as to how much power they can produce since CO2 has a set vapor pressure of 850 psi, or about 56 bar at room temperature which is around 25 C or 77 F. CO2 Gas also requires a warm environment to expand so warmer temperature and longer barrels help with power.

• Some CO2 guns can also use pressurized air tanks in place of CO2.

Spring Piston Airguns:

• Spring Airguns use the release of a pre-cocked spring and plunger system to compress air to power the ammo.

• Spring Piston Airguns require the cocking of the spring between each shot so they are single shot only.

• Spring Airguns are limited to how much effort is humanly possible to cock the spring into position. If you make the spring to strong then not everyone will be able to use the Airgun effectively. Too week of a spring and the Airgun will lack power.

• Spring Piston Airguns are known for having a fair amount of recoil and vibration when the spring moves both forward and backwards quickly inside the Airgun.

• Spring Airguns can use either a mechanical spring or a gas spring.

Pump Airguns:

• Pump Airguns (either Single or Multi-Pump) store air pressure in a chamber that when released, powers the ammo.

• Most Pump Airguns require at least 1 or more pumps, often up to 10 pumps for each shot and you generally only get one shot per set of pumps. Not to be confused with PCP Airguns (Pre Charged Pneumatic) which have large pressure tanks that are recharged with a high volume of pressurized air that is capable of shooting multiple shots per charge.

• Pump Airguns are also somewhat limited to how much effort is humanly possible since the higher the chamber pressure, the harder it will be to pump the Airgun. 

Misc Airguns:

• Generally speaking both Spring and Multi-Pump Airguns have more potential power than a CO2 guns since CO2 has a set peek pressure limit.

• Pump and CO2 Airguns are know to have very little recoil since the pressure is stored in a chamber and then released by a valve. No slapping back and forth of a large internal spring.

Pros:

CO2 Airguns:

• CO2 Airguns allow for multiple shots per CO2 cartridge for more realistic action shooting.

• CO2 Airguns do not require any human effort to charge the gun other than loading the CO2 and Ammo into the Airgun.

• CO2 Airguns allow for true semi auto shooting ability. 

Spring Piston Airguns:

• Spring Airguns have the potential for high velocity since the larger and stiffer the spring, the greater the output force.

• Spring Airguns do not require anything other than your ammunition, typically either a Pellet or BB.

• Spring Airguns are mechanically very simple which makes them very reliable and less expensive to produce than other types of Airguns. 

Pump Airguns:

• Pump Airguns have the potential for high velocity since more pumps equals greater output force, only limited by the users strength and the pressure rating of the Airgun.

• Pump Airguns do not require anything other than your ammunition, typically either a Pellet or BB.

• Pump Airguns have next to no recoil which makes them very easy to shoot and highly accurate.

Cons:

CO2 Airguns:

• CO2 Airguns require the purchase and use of CO2 or they simple do not work.

• CO2 Airguns are very susceptible to temperature changes, especially cold temperature since CO2 needs a warm environment in order to expand. Cool down effect also plays a role in power output.

• CO2 Airguns have a maximum set amount of power output.

Spring Piston Airguns:

• Spring Airguns require the pre-cocking of the spring for each shot.

• Spring Airguns can take some getting used to since the spring recoil/vibration requires a very lose grip (Military Grip) to shoot accurately with them.

• Spring Airguns should not be stored pre-cocked since this can damage the spring, less so with gas spring versions. 

Pump Airguns:

• Pump Airguns require pre-pumping to pressurize the air chamber for each shot.

• Pump Airguns, especially Multi-Pump Airguns take the most amount of human effort for each shot.

• Pump Airguns need to stored with at least one pump in them or the seals can get damaged over time.

In many of my reviews I show the loading process of each gun but sometimes I either skim over this part or assume most people already know how to load an Air Pistol and skip it entirely. Well as it turns out not everybody does know how to load up an Airgun or they are unclear on certain areas, like do you actually need the CO2 and how long can you leave CO2 in an airgun?

So I made a video specifically to cover how to load CO2, BB's and/or Pellets into your Air Pistol.

Now even though this video is targeted at 4.5mm Steel BB and Lead Pellet Pistols, there is a crossover with 6mm Airsoft Pistols so this video may also help an Airsoft shooter.

Our Family Bearded Dragon (Dijon) was looking rather sad and lonely today so I figured he could hang out while I made the video, he really doesn't do much of anything most of the time so why not give him a special appearance in one of the Replica Airguns Videos ;)

Two questions that come up over and over again and to be honest I just hate answering, mainly because both of these questions to me are kind of common sense questions. I feel if someone where to stop and actually think about teh question, the answers would become obvious.

That said, common sense has to be learned somewhere and not all of us are exposed to the same life experiences so here goes...

The two questions are:

• Will this Ammunition Work in my Gun?

• Can I Convert a Blank Gun to a Real Gun?

The answer for both of these question is actually the same! Use the ammo made for your gun and do not try to use anything other than the ammo that was made for your gun. Do not try to modify your gun to shoot anything other than the ammo that was made for it, if you do, you may be breaking the law and could land yourself in jail. If you can follow these rules then your ammo and gun will work as intended :)

So that's pretty much it in a nutshell, watch my YouTube video below as I show you examples of ammo types with visuals on exactly why you need to use the ammo made for your gun. I also talk about the dangers of attempting to modify a blank gun to shoot some sort of real bullet and why it is a very bad idea in so many ways to try and convert a blank gun into a real gun.

Buy the ROHM RG-88 9mm P.A.K. Blank Pistol in the Canada Store

Buy the ROHM RG-88 9mm P.A.K. Blank Pistol in the US Store

This video should go "Hand in Hand" (pun intended) with my Best Two Handed Pistol Grip Tutorial Video that I did last year back in August. After that video I had several people ask me to talk about how to aim a gun. I guess if you have been shooting guns for a while you kind of take it all for granted but after teaching my kids the proper way to aim a gun at a target, this info is not naturally born into us ;)

This video demonstrate how and where to place your open gun sights on a target and also how you can compensate for a gun that may not be perfectly sighted in.

Type: Airsoft AR M16 Styled Rifle.

Manufacturer:G&G.

Model:CM16 Carbine GBB.

Materials: Metal and plastic/fiber construction.

Weight: 5 pounds.

Barrel: 10 inches, metal non-rifled.

Propulsion: GBB

Action: Semi & full auto blowback.

Ammunition Type: 6mm plastic Airsoft BB's.

Ammunition Capacity: 30+ round magazine.

FPS: 370+.

I could pretty much copy and paste my review of my G&G CM16 Raider GBB since both of these guns are pretty much the same Airsoft Rifle with different finishings. Instead I will place a link to my G&G CM16 RaiderVersion 2 GBB AR Airsoft Rifle Review and insert some nice photos of the  G&G CM16 Carbine version for you to admire :)

Buy the G&G CM16 Raider GBB Airsoft Rifle in Canada - Buy G&G Airsoft Rifles in the US

This is take 2 of my Modification to my F1 Chrony Chronograph. The purpose of this modification is to improve the low light FPS readings. In my first attempt I used LED Puck Lights but they where the kind that used flat panel LED's and they only had 4 panels per LED Puck which made each LED panel kind of bright. I did get OK with my first mod using LED Puck Lights but not as good as I would like to see.

So here we are with take 2 of F1 Chrony Chronograph LED Puck Light modification and this time around I am using standard bulb styled LED lights and to improve my chances of this working I went with and LED Puck that contained 24 LED bulb lights per puck, this way each light on it's own is a bit dimmer which I feel will give a more diffused lighting effect and hopeful consistent fps readings.

By the way I got these LED Puck Lights at my local dollar store for $2.50 each so not a very expensive modification, especially if they work.

Well... Watch the video and see how they perform...

This video was made to show you the results I got by mounting LED puck lights to the top of my F1 Chrony Chronograph defuser panel in order to improve the low light Feet Per Second readings when using 4.5mm Steel BB's.

I have been struggling with my F1 Chrony Chronograph during the fall and winter months as tit becomes overcast and dark where I live. There have been days where I have gone out to shoot my field test shooting video and not been able to get any Chronograph fps results which is very frustrating because much time and effort goes into the planning setup of each video.

I was given advice from several of my viewers to mount an LED puck style light on the back side of my Chronograph defuser panel and that this helps the Chronograph to read much better in low light situations.

I bought a multipack of the LED puck lights from my local Costco but they did not work as well as I expected them to as they had a panel style of LED rather than the bulb shaped LED which I think may diffuse the light a bit more. My next experiments will be done using LED Puck lights but with the bulb styled LED.

You can watch my video to see how my first attempt using an LED Puck light with my F1 Chrony Chronograph worked out.