Type: Airsoft GBB Rifle.

Manufacturer:WE.

Model:AK74UN.

Materials: Metal & plastic.

Weight: 6.9 pounds (3115 Grams).

Barrel: 9 inches, smooth bore.

Propulsion: (GBB) Gas Blowback.

Action: Semi & full auto.

Ammunition Type: Airsoft 6mm Plastic BB's.

Ammunition Capacity: 30 rounds.

FPS: 400+.

Trigger Pull: The trigger pull on the WE AK74UN GBB Airsoft Rifle is very light (maybe even under 1 pound) since the blowback action has already pre-cocking the action making  this rifle single action only. The take-up is very short, about one eighth of an inch or even less! The magazine has two switches, the one on the top allows you to dry fire while the one on the backside resets the trigger block. You will need to push the side switch down after reloading your magazine to allow the trigger/hammer to function again.

Accuracy: Out of the box the WE AK74UN Airsoft Rifle shot on the high side for me, about 8 inches at 30 feet, you can adjust the front sight post to some degree for elevation but I was not able to find any way of adjusting the windage? I did my pretest shooting from the 30 foot mark and I found the WE AK74UN Gas Blowback Airsoft Rifle AK74 Replica shot a very respectable 5 shot 1.5 inch group in semi auto which opened up of course when I shot the rest of the rounds in full auto. The full auto group stayed pretty tight considering all the recoil that was going on. I would say this gun should be able to shoot fairly accurately at distances even greater than 50 feet and even in full auto.

Build Quality: The WE AK74UN Airsoft Rifle is very well made with a lot of actual stamped steel parts, the only metal (zinc alloy) would be the trigger group, bolt, and part of the front sight, the pistol grip and front stock are made out of a matt finished hard plastic. Fit and finish is near perfect and I had no problems with the functionality of this Airsoft replica in any way. There are third party steel replacement parts for the trigger group and bolt if you want to swap these out at some point.

Realism: Everything about this gun is realistic! Operation, field stripping, tones of steel and metal parts, the long travel bolt, the slower cycle rate, and the heavy recoil all make the WE AK74UN GBB Airsoft Rifle as near perfect a working replica that you can find. Sure WE modernized this AK74 variant a bit with the addition of some enhancements but they do work well and make this Airsoft rifle very usable.

Reviewed by:Replica Airguns.

Pros:

• Long travel bolt with heavy blowback, lower cycle rate like a real AK!

• Lots of steel and metal in this gun, very hefty and solid.

• Awesome blowback kick really hits you in the shoulder.

• Semi auto & full auto selectable.

• Field strips just like the real AK.

• Nice high 400+ FPS and good 1.5 inch 5 shot group from 30 feet away.

• Decent use of Gas.

• Modified improved selector/safety switch can be used with trigger finger and also can be used to lock the bolt back for easy hop-up adjustments.

• Magwell guide helps with insertion of the magazine.

Cons:

• Long travel bolt kicks so hard that it can wear the softer Zinc Alloy internal parts quickly like the bolt and trigger grouping.

• Sights are not really very adjustable, at least for windage.

Comments:

I really love my WE AK74UN Gas Blowback Airsoft Rifle, it is truly one of the most realistic replica guns I own, not just in looks but in how it functions and shoots. The heavy use of stamped steel, lots of metal throughout, full travel bolt with heavy blowback and realistic AK cycle rate make this one of the most fun guns to shoot that I own. If you're looking for a Gas Blowback AK styled Airsoft rifle this one is one of the best out there! 

My Vimeo Table Top Video REVIEW of the WE AK74UN Gas Blowback Airsoft Rifle:

Buy Airsoft gun in the Canada Store  -  Buy Airsoft gun in the US Store

Photo of WE G18C Removed by Request from Glock "Renzulli Law Firm"

All references, photos and video claiming that any item in this review/video looks like a Glock or is a Replica of a Glock in any way shape or form have been removed from this post as requested by Glock"Renzulli Law Firm"

Type: Airsoft GBB Pistol.
Manufacturer: WE.
Model: G18C.
Materials: Metal & plastic.
Weight: 1.7 pounds (776 Grams).
Barrel: 4.5 inches, smooth bore.
Propulsion: (GBB) Gas Blowback.
Action: Semi & full auto.
Ammunition Type: Airsoft 6mm Plastic BB's.
Ammunition Capacity: 25 rounds.
FPS: Up-to 380 with longer barrel attached.
Trigger Pull: The trigger pull on the WE G18C is very nice and light since the blowback action does most of the work pre-cocking the action. There is a built in and working trigger safety like you would find on a real steel NAME REMOVED with about a quarter inch of take-up leading to a very light and crisp release.

Photo of WE G18C Removed by Request from Glock "Renzulli Law Firm" 

Accuracy: Out of the Box the WE G18C shot great rather well for me when I did my pretest from the 20 foot mark, I found the WE G18C was dialed in pretty decent and shot very close to the bulls eye, maybe a hair to the left which is good since the sights are non adjustable. I shot a very respectable 5 shot 1.5 inch group in semi auto which opened up a great deal when I shot the remaining 15 rounds but at least they all seemed to stay pretty much on the paper which is not bad considering how much this gun jumps around in full auto.

Photo of WE G18C Removed by Request from Glock "Renzulli Law Firm" 

Build Quality: The WE G18C Airsoft seems to be well made, and you will find lots of metal parts where they need to be, again similar as what you would find in a real NAME REMOVED. Fit and finish is nice but I did have an issue with the gas tube when I first got mine, it broke rendering the gun inoperable, a quick swap out with a new gas tube and all is well and so far after a number of magazine worth of shots the WE G18C is still working well and the new gas tube is holding up.

Photo of WE G18C Removed by Request from Glock "Renzulli Law Firm" 

Realism: WE has taken some liberty with the markings on their WE G 18C copy, they are similar to what you would find on a real NAME REMOVED but not actually the same, as longs as you don't look too closely you will most likely be fooled into believing it's a licensed NAME REMOVED! As for how the WE G18C is built and how it operates, you will find it's a dead ringer to a real steel NAME RMOVED and even breaks down exactly the same.
Reviewed by: Replica Airguns. 

Photo of WE G18C Removed by Request from Glock "Renzulli Law Firm"

Pros:

• It's a NAME REMOVED Replica!
• Lots of metal in this gun similar to a real NAME REMOVED.
• Kind of licensed similar to a NAME REMOVED.
• Semi auto & full auto selectable :)
• Very solid blowback kick.
• Field strips just like a NAME REMOVED.
• Very good accuracy and power even with the shorter barrel installed
• Comes with two barrels, one for use with the suppressor to increase fps for Canadian import. 

Photo of WE G18C Removed by Request from Glock "Renzulli Law Firm"

Cons:

• No real sight adjustments.
• Had a problem with the Gas Tube cracking almost right out of the box. 

Photo of WE G18C Removed by Request from Glock "Renzulli Law Firm"

Comments:
I have heard many people say they love WE products and then there are some that claim they are not all that well made! Other than my issue with the cracked gas tube, my WE G18C is holding up well and is working nicely, I think some earlier WE products lacked some refinement which may have led to problems but from what I have heard as of late, WE has stepped things up and is making a better product these days. My WE AK74UN is a testament to this as it is built like a tank and has tons of real stamped steel all throughout. Getting back to the WE G18C Airsoft GBB, it's really fun to shoot with it's amazing blowback and for a GBB pistol it shoots pretty hard and finds the target with easy. 

Photo of WE G18C Removed by Request from Glock "Renzulli Law Firm"

My YouTube Video of the WE G18C Gas Blowback Airsoft Pistol:

Buy Airsoft gun in the Canada Store  -  Buy Airsoft gun in the US Store

• Checkout my Table Top Review for the Umarex Walther P99 CO2 Blowback Airsoft Pistol:

The Umarex Walther P99 CO2 Blowback Airsoft Pistol is a fairly low cost Airsoft BB pistol but even so, there is no reason why we should expect less than stellar performance from it.

I have already done a pretest for the Umarex Walther P99 CO2 Blowback Airsoft Pistol while making my Table Top Review and it shot right around the 333 fps mark, but it was a colder day then. I also shot my Umarex Walther P99 DAO from a much closer 20 foot distance for the pretest and got a respectable 2 inch grouping.

On the actual Field Test Shooting day it was much warmer (tank top weather ;) and so as would be expected, this time my Umarex Walther Airsoft P99 shot a bit quicker at right around a 356 fps average, shooting 10 rounds through my Chronograph. I would expect to get even more fps on an even hotter day as it was only about 22 degrees Celsius or about 72 Fahrenheit on this test day.

Accuracy from 30 feet out was pretty close to my pretest 20 foot testing if you exclude the two flyers but again the Umarex Airsoft P99 version was shooting a bit to the left which unfortunately can not be adjusted other than changing my sight position on the target. I would think the trend to the left will only increase as we shoot further out but this gun is really best suited for close quarters shooting anyways and should have no problems right up to 50 feet shooting a man sized target..

You can expect to get around 100 shots or a good 6 full 15 shot magazines from Umarex Walther P99 CO2 Blowback Airsoft Pistol which should get you nicely through a CQB match without having to change CO2 cartridges. For being a rather low cost Airsoft gun, it did perform well enough for me on this day, keep in mind it does have a firm long pull double action only trigger so really fast shooting will take it's toll on your trigger finger ;)

Watch my Field Test Shooting Video for the Umarex Walther P99 CO2 Blowback Airsoft Pistol:

Buy this Airsoft Pistol in Canada  -  Buy this Airsoft Pistol in the US

• Checkout my Table Top Review for the ASG Dan Wesson 6 Inch Silver CO2 Airsoft Revolver:

I've had the opportunity to review and shoot my Dan Wesson 4.5mm Steel BB Version so I kind of knew what to expect with the Airsoft version, much of the same but with perhaps a little bit less accurate further out shooting since the plastic BB's will tend to drift a bit more.

I already did my pretest for the ASG Dan Wesson 6 Inch Silver CO2 Airsoft Revolver while making my Table Top Review and shot right around the 400 fps mark, but it was a colder day then, I also shot my ASG Dan Wesson Airsoft Revolver from a closer up 20 feet for the pretest and got a nice tight 1.5 inch shot group.

On the actual Field Test Shooting day it was much warmer (tank top weather ;) and so as would be expected, this time my ASG Dan Wesson 6 Inch Silver CO2 Airsoft Revolver shot a bit faster at closer to a 420 fps average with 6 shots put through it. There is even room for some more fps still as it was only about 22 degrees Celsius or about 72 Fahrenheit on the test day.

Accuracy from 30 feet out was not as tight as my pretest 20 foot testing and I would imagine this will spread out even more the further back we go with the Airsoft ASG Dan Wesson, as is the case with Airsoft BB's. Airsoft BB's are just not as accurate as steel BB's especially when shooting at longer ranges. I would expect this Airsoft Dan Wesson version should still be very effective on a "man sized target" up to about 60 feet or so. Keep in mind there is no hop-up in this revolver so teh Airsoft BB's will drop much more than a gun that has hop-up.

Like the 4.5mm BB shooting version you can expect a good 100 or more shots from this Airsoft BB Shooting Dan Wesson CO2 Revolver. Having tradition revolver single and double action makes for both precise and action styled shooting. All in all a really nice Airsoft pistol from ASG.

Watch my Field Test Shooting Video for the ASG Dan Wesson 6 Inch Silver CO2 Airsoft Revolver:

Buy ASG Airsoft Pistols in Canada  -  Buy ASG Airsoft Pistols in the US

• Checkout my Field Test Review for the Umarex Walther P99 CO2 Blowback Airsoft Pistol:

Type: Airsoft Pistol.

Manufacturer: Umarex.

Model: Walther P99 DAO

Materials: Metal & Polymer.

Weight: 1.5 pounds.

Barrel: 4 inches, metal non-rifled.

Propulsion: 12 gram CO2.

Action: Semi auto, double action only with blowback.

Ammunition Type: 6mm plastic Airsoft BB's.

Ammunition Capacity: 15 round stick magazine.

FPS: 380.

Trigger Pull: The Double Action Only trigger pull on the Umarex Walther P99 CO2 Blowback Airsoft Pistol is long but not overly heavy for a double action trigger, it does have a break point mid way where it locks partway back, I presume this is the point in which a BB is loaded from the magazine into the barrel? The rest of the pull is still medium but much shorter with a distinct release point.

Accuracy: I did do a quick preliminary test before I made this table top review to get an idea of where this gun performs in terms of FPS and accuracy, I shot 5 rounds through my Chronograph on a fresh CO2 and got an average of 333FPS which was a bit lower than the claimed 380 but it was not the hottest of days. I also stepped back 20 feet and from a semi rested position I was able to get 9 shots within 2 inches of each other which was not bad for a DAO gun that I have never shot before. I did shoot a bit down and to the left with the set sights.

Build Quality: The Umarex Walther P99 is well built for its rather low price tag, it may not have all the bells and whistles but it does get the job done with good fit and finish and materials used. You will find a plastic/polymer frame but there is a lot of metal where it would normally be found on the real steel version like in the slide, magazine, trigger, slide catch, magazine release, inner barrel and many other internal parts. No real complaints here!

Realism: The Umarex Walther P99 CO2 Blowback Airsoft Pistol is pretty close in looks to a real steel Walther P99 with the exception of a missing decocker, but I'm pretty sure this is the same with the real steel DAO version? There is also the funny looking safety on the right side of the frame found on many Umarex airguns. I have to mention the red tip but again this can be removed and even when removed the barrel it is still recessed which adds to the realism. The Blowback action, Walther licensing and nice heavy weight all add up to make this Airsoft pistol look and feel the part.

Purchase it from: The Replica Airguns Store

Pros:

• Low cost for a very believable and solid replica.

• All metal stick magazine.

• Metal slide and internal parts gives it decent weight.

• Rail for accessories.

• Well hidden CO2 screw.

• Walther licensing.

• Recessed inner barrel.

• White dot sights, easy to use.

• Right amount of power for indoor CQB style airsoft games.

Cons:

• Comes with a red tip even in Canada.

• Double action only, so trigger is a bit heavier.

• Kind of funny safety, not like the real gun.

• Blowback was a bit sluggish.

Comments:

Overall the Umarex Walther P99 CO2 Blowback Airsoft Pistol is a very good buy, it's a decent replica of the real steel Walther P99 with blowback operation, lots of metal parts, good fit and finish, decent performance and full Walther licensing and trademarks. All at a very affordable price tag. It may lack some of the extras you will find on more expensive and more functional Airsoft pistols but the simplicity of the Umarex Walther P99 CO2 Blowback Airsoft Pistol means it will most likely be a bit more reliable with less to go wrong down the road. If you have been looking for a nice Walther styled replica in an Airsoft version this may be just be the ticket!

My Vimeo Video Review for the Umarex Walther P99 CO2 Blowback Airsoft Pistol:

Buy the Umarex P99 CO2 Pistol in Canada 

Buy the Umarex P99 CO2 Pistol in the US

• Checkout my Field Test Review for the ASG Dan Wesson 6 Inch Silver CO2 Airsoft Revolver:

Type: Airsoft Revolver.

Manufacturer: ASG.

Model:Dan Wesson 6 inch Sliver Airsoft.

Materials: Mostly metal.

Weight: 2.25 pounds. (968 grams)

Barrel: Metal non-rifled.

Propulsion: CO2 x 1.

Action: Revolver, single and double action.

Ammunition Type: 6mm plastic Airsoft BB's.

Ammunition Capacity: 6 rounds.

FPS: 453.

Trigger Pull: The ASG Dan Wesson Airsoft Revolver has a predictable trigger with the single action being a bit lighter and more consistent, not just in feel but also in fps. Double action shooting is very usable without a lot of extra pressure required and makes for fun consecutive shooting albeit you will run our of ammo pretty quick compared to many high capacity semi auto styled airguns.

Accuracy: I shot the Dan Wesson Airsoft Revolver at a target from 20 feet away in a semi rested position, and it performed excellent, getting a 1.5 inch 6 shot grouping dead center in the bullseye! The sights are fully adjustable for elevation and windage so getting these guns centered on the bullseye if you where out a bit would be very easy. My Chrony testing for the Dan Wesson Airsoft Revolver with a six shots averaged result was 399 fps.

Build Quality: This detailed revolver is extremely well built! All the Dan Wesson Revolvers are almost all metal with just a few components made out of plastic, like the handle and CO2 screw tab. The handle feels like a cross between plastic and rubber but is basically plastic with a coated paint on it that can wear off with long term use so try and go easy on the grips. The finish on the six inch silver Dan Wesson is amazing and looks just like polished stainless steel. Very nice indeed!

Realism: The ASG Dan Wesson BB revolvers are as close as you can get to a real six shooter, ASG didn't leave out any details and has really brought us an extremely believable CO2 revolver that mimics the real steel in almost every way! Loading and ejecting actual brass shells into the cylinder makes you feel like this gun is much more then an unassuming airgun!

Purchased From: The Replica Airguns Store.

Pros:

• It's a revolver with actual brass shells giving you the feeling of a real 6 shooter!

• Almost all metal design.

• lots of detail in this gun, very well made, fit and finish is excellent.

• Good power and good accuracy.

• Fully adjustable sights.

• Can mount a scope of some sort on it with the rail attached.

• Right amount of power, even for some indoor CQB style airsoft games

Cons:

• Plastic CO2 screw tab (but is well hidden and protected).

• Grips can wear a bit with extended use.

• Red tip on the US version :(

Comments:

I wasn't really a revolver person until I got my Dan Wesson's! They are really fun to shoot and yes you only get to fire off 6 shots at a time but the reloading is kind of fun and adds to the realism of shooting a revolver styled gun. The other benefit to taking breaks every 6 shots to reload is the time it allows your CO2 and gun to warm up which increases the overall FPS and shots per CO2. I am not sure if a large six shot revolver is the way to go when in a high intensity Airsoft game but I can tell you when you're on the other end of the barrel of one of these you are probably not thinking how many shots does he have left :)

My Vimeo Video Table Top Review for this amazingly real Airsoft Revolver:

Buy ASG Airsoft Pistols in Canada  -  Buy ASG Airsoft Pistols in the US

• Also checkout my Table Top Review for the Umarex - KWA MP7 Blowback Airsoft PDW:

The rainy weather let up today so I grabbed up my Umarex - KWA MP7 Blowback Airsoft PDW and put it through its paces today. I was a bit surprised that my groupings from 30 feet away shooting from a semi-rested position where a bit spread out, mostly top to bottom. Perhaps the hop up was effecting the MP7? The good news is that shooting in full auto did not seem to make things any worse :) I was using .25 gram BB's for the accuracy test.

As for the Chronograph portion of this field test shooting review, the Umarex - KWA MP7 Blowback Airsoft Machine Pistol shot a bit higher than claimed at just over 400 fps using .20 gram BB's with Propane Gas. I had no problems shooting a full magazine of 40 rounds with a full gas fill up and the cycle rate stayed nice and high with very little cool down effect.

I really enjoyed shooting the Umarex - KWA MP7 Blowback Airsoft PDW, it has a nice sound with just the right amount of blowback to give it a good feel without throwing off the sights, the trigger was very light and responsive and I ended up preferring to use the pop up sights over the pistol sights as I was shooting mostly with the stock and fore grip open. Those Cans never had a chance!

All in all the Umarex - KWA MP7 Blowback Airsoft PDW is one of the coolest compact and ultra modern Airsoft guns I have had the pleasure to review and test out.

Watch my Field Test Shooting Vimeo Video for the Umarex - KWA MP7 Blowback Airsoft PDW:

Buy this Airsoft Machine Pistol in Canada  -  Buy this Airsoft Machine Pistol in the US

• Also checkout my Field Test Review for the Umarex - KWA MP7 Blowback Airsoft PDW:

Type: Airsoft Machine Pistol (PDW).

Manufacturer:Umarex - KWA.

Model: H&K MP7 A1.

Materials: Metal & plastic.

Weight: 4 pounds, 7 ounces (2130 grams).

Barrel: 6.3 inches, smooth bore.

Propulsion: GBB - Gas Blowback.

Action: Semi-full auto selectable SAO.

Ammunition Type: Airsoft 6mm Plastic BB's.

Ammunition Capacity: 40 rounds.

FPS: 370.

Trigger Pull: The trigger pull on the Umarex - KWA H&K MP7 A1 is single action only as the charging handle has to be pulled back to open and release the bolt for the first shot fired. There is a trigger safety that must be engaged to fire, but it is not noticeable when shooting this Airsoft PDW. There is a short take-up and then a nice light release and short reset.

Accuracy: I was able to get decent accuracy in both semi auto and full auto burst with my H&K MP7 due to the mild to medium blowback. I would say I shot somewhere in the 2-3 spread with my 10 shot grouping from 20 feet out. When I do my full Field Test Shooting Review I will take it back a bit further and shoot form 30 feet out. I did get a bit higher then claimed fps right up into the 400 fps range when testing the Umarex - KWA H&K MP7 A1 on my Chronograph.

Build Quality: The Umarex - KWA H&K MP7 A1 Airsoft PDW is built extremely well, using near exact components that you would find on the real HK MP7, yes it has a plastic or polymer shell but that is what you would find on the 4.6mm x 30 real steel version. The Umarex MP7 Airsoft PDW does use lots of metal where it needs to be like in the internal housing, pins, bolt, barrel, rails and even the magazine. The fit and finish is bang on, this gun is as solid as they come!

Realism: I have to say the Umarex - KWA H&K MP7 A1 is pretty much a bang on copy of the real steel H&K MP7. The only telltale sign is the Umarex branding and warning label on the right side receiver, even the 6mm caliber markings are near impossible to make out on the underside right beside the serial number plate. Of course the red flash hider is a big "red flag" that takes away form the realism but for us here in Canada, a bit of red paint is all that is needed to fix that problem. just be aware that the flash hider is really glued on tight so plan that project accordingly!

Available at the: Canada Replica Airguns Store, US Replica Airguns Store

Pros:

• Excellent attention to detail with lots of working parts.

• Full H&K licensing and markings.

• Good overall 400 fps power for a short barreled gas blowback gun.

• Very nice trigger with working trigger safety.

• Lots of metal parts where they need to be and would be on the real K&H MP7 PDW.

• Semi auto & full auto selectable.

• High capacity GBB magazine (40 rounds)

• Sights are fully adjustable and offer two positions.

• Built in for-grip and rear slide-out stock

• Easy access to hop up system.

Cons:

• Came with the orange tip, you may want to  paint it. (hard to get off as it is glued on!)

• May be too powerful for CQB skirmishes without some detuning.

Comments:

I really like the Umarex - KWA H&K MP7 A1 Airsoft PDW, it's my kind of Airsoft gun! I love the modern look, I love the features and the price is also really good for what you are getting here, a GBB gun that is super versatile and can be used in close our out at range. The build quality is what impressed me the most, this Airsoft gun is super solid, that combined with the attention to every detail would fool just about anyone that it's not the real deal until a very close inspection is done:) The Umarex - KWA H&K MP7 A1 reminds me of the other ASG MP9 KWA built PDW I reviewed earlier, they are like two peas in a pod but both with their own unique personalities.

Buy this Airsoft Rifle in Canada
Buy this Airsoft Rifle in the US

• Also watch my Tabel Top Review for the B&W Dragunova SVD Airsoft Sniper Rifle:

I had a chance today to get out and shoot my B&W Dragunova SVD Airsoft Sniper Rifle, the weather held out just long enough for me to setup my target a good 90-100 feet out in the field but as luck would have it, it started to rain on my camera gear right as I started doing my target shooting test using .36 gram Airsoft BB's. So in a bit of a rush, I shot off a good 10 rounds and was able to put most of them on the paper which from 100 feet out using an Airsoft rifle on a target the size of a standard 8x11 sheet of paper is not too bad at all, and don't forget I was just using the iron sights.

I found I didn't even need to use the hight adjustment on my rear sight as the hop-up seemed to keep the Airsoft BB's floating nicely on plane all the way to at least 100 feet. By the way if you watched my earlier Table Top Reviews I mentioned the B&W Dragunova SVD was shooting a bit to the left even after full windage adjustment to the right, well I managed to sort this out and pull the sight the little bit extra I needed to get it pretty much dead center.

Moving on to the Chronograph portion of this Field Test Shooting Review, I got the same results as my pretest with an average fps of 498 using .20 gram Airsoft BB's and an average fps of 277 using the heavier .36 gram BB's. I have heard that the B&W Dragunova SVD Airsoft Sniper Rifle can be a bit of a chore to cock but for me it was actually pretty easy and using a left overhand approach worked well, allowing me to cock the charging handle pretty easy while keeping my finger on the trigger and the rifle in position ready for my next shot.

The iron sights and the trigger setup seem to both work very well with this rifle, I really have no real complaints and really enjoyed shooting the B&W Dragunova SVD Airsoft Sniper Rifle. If the rain hadn't been coming down on my camera gear I may have put a bunch more shots into the target for the simple reason I was having so much fun :)

Watch my Field Test Shooting YouTube Video for the B&W Dragunova SVD Airsoft Sniper Rifle:

Buy the B&W Dragunova SVD in the Canada Store  -  Buy Airsoft Rifles in the US Store

• Watch my Field Test Shooting Review for the B&W Dragunova SVD.

Type: Airsoft Rifle.

Manufacturer:B&W Airsoft (AIM TOP).

Model: SVD Dragunova.

Materials: Metal & plastic.

Weight: 6 pounds, 4 ounces (2.85kg).

Barrel: 23 inches, smooth bore.

Propulsion: Spring.

Action: Charging handle single shot.

Ammunition Type: Airsoft 6mm Plastic BB's.

Ammunition Capacity: 40 rounds.

FPS: Up-to 500.

Trigger Pull: The trigger pull on the B&W Dragunova SVD Airsoft Sniper Rifle is good overall, just a bit of initial take-up and then a medium trigger pull to release the heavy spring. You will of course nee to pull the charging handle with each shot to preload the spring.

Accuracy: My initial accuracy testing was done from about 45-50 out using .36 gram Airsoft BB's, it was a fairly windy day but  even so I was able to get a nice tight 2 inch grouping using a semi rested position. I also put the Dragunova SVD through my Chronograph testing and shot both the lighter .20 gram and heavier .36 gram BB's to see what kind of fps I would get using both weights. The lighter .20 gram BB's got right around 500 fps while the heavier .36 gram BB's shot a bit lower at approximately 380 fps. I did however find that sighting the SVD in for windage adjustments (left and right) was a bit of a challenge as you can only adjust the front sight by loosening it with an allen key and make only very slight left to right adjustments. I was not able to get the SVD to shoot far enough to the right using this method so I amy need to do figure something else out, perhaps a scope setup?

Build Quality: The B&W Dragunova SVD Airsoft Sniper Rifle is not a super expensive rifle but still has a good combination of metal and plastic components. Most of the parts that you would find on the real SVD are metal including the barrel, bolt/charging handle & receiver, trigger, magazine, sights, strap rings and rial system. The stock is of course plastic with some added rubber. The B&W Dragunova SVD is not overly heavy but still has a reasonable amount of weight to make it believable. Performance was very good with no mechanical problems other than the last two BB's in each magazine do not load into the rifle.

Realism: I have never held an actual Dragunova SVD in my hands but from what I have seen in photos, it looks to be a good copy of the real steel Russian sniper rifle. Lots of metal helps pull of the realism, a working charging handle, removable bolt cover, and lots of other working components make for a believable looking and functioning version of this Airsoft BB shooting Dragunova SVD Sniper Rifle.

Available in the: Canada Replica Airguns Store.

Pros:

• Lots of metal parts throughout where they would be on the real SVD.
• Good power and accuracy combination.
• Fairly high capacity magazine at 40 rounds.
• Sights are adjustable for elevation front and back and a bit for windage.
• Bolt is surprisingly easy enough to cock with either left or right hand.
• Lots of upgrades available for this sniper rifle.
• Inexpensive way to own a piece of history.

Cons:

• Some discrepancies in the manual (180 fps and 100 round magazine)
• Sighting for windage may not be adequate?
• Would definitely be much nicer with the wood stocks.
• Two BB's always pop out of the magazine area when empty.

Comments:

I found the B&W Dragunova SVD Airsoft Sniper Rifle to be a lot of fun to shoot, I was not sure how the charging handle system was going to work in terms of weight and easy of use to pull it back. I ended up using my left hand and reaching across and over and surprisingly this was very efficient and effective in charging the spring and allowed me to keep my righthand in place and on the trigger for very quick follow up shots. Power was as much as you would want from a sniper rifle and accuracy was also very good even in windy conditions. The only real problems I had where the two BB's that did not load from each magazine and the windage adjustments not quite allowing me to move my aim point enough for a bullseye at 50 feet out. I would recommend this B&W Dragunova SVD Airsoft Sniper Rifle and would suggest possibly adding some wood stocks and a magnified scope setup.

 Buy Airsoft Rifles in the Canada Store

Buy Airsoft Rifles in the US Store

Every once in a while something goes wrong and your favorite BB shooter stops working as it should :( One of the most common problems I see with many of the full blowback BB and Airsoft pistols are BB's getting stuck in the gas tube. This is because this style of gun loads a BB into the breach area of the barrel every time you rack the slide forward. Of course this is only when there are BB's in the magazine.

The semi auto style of these guns is similar to that of a real gun, the blowback operates the slide which in turn moves back and then forward and loads a BB into the chamber. With a real gun, if you where to rack the slide manually again without shooting it, the chambered round would be ejected by the extractor but with a BB gun there is no extractor because there is no spent shell to eject. So multiple BB's can be loaded into the chamber area of the barrel overloading it and if the BB's have nowhere to go they just jam up and often go back into the gas tube which can cause all kinds of problems...

In this Cybergun KWC Tanfoglio Witness 1911 Stuck BB Removal Tutorial Video, I show you how to remove a BB or even multiple BB's from the gas tube area which in short requires; the removal of the slide and guid rod and spring so that you can push the gas tube forward and shake the BB out of the front of the gas tube.

Watch my Vimeo Video on how to remove a stuck BB from the Gas Tube on my Tanfoglio Witness 1911.

Buy KWC/Cybergun 1911 BB in Canada   -   Buy KWC/Cybergun 1911 BB in the US

Testing out the ASG - Marushin CZ 75 Blowback Shell Ejecting Airsoft Pistol was not an easy one but I did manage to get thorough it! First there was the setup, I could not shoot the ASG Shell Ejecting CZ 75 Airsoft pistol on my deck or I would have fore sure lost most of my shell casings for it. So I decided to setup camp in my pool area where I have a nice large flat area off to one side, I put down a ginormous tarp in hopes to catch the radically flying shells but even this failsafe did not catch them all as I later found out ;)

As with most of my Field Test Shooting videos, I usually do a bit of a pre test to make sure the gun is functioning properly and so I shot a full magazine of my brass shells through the ASG CZ 75 and it worked like a charm, of course when I started recording the live video it decided not to work at all and I still do not know why? I was able to revert back to the plastic shell casing that came with my ASG CZ 75 Blowback Shell Ejecting Airsoft Pistol and they seemed to be working so I went with them for my testing. Interestingly enough the brass shells got much higher fps (around 300+) when I did my pretest compared to around the 250 average fps I was getting with the plastic shell casings.

Shooting on target proved to be better than I though once I raised my sight point up a bit, the gun likes to shoot a bit low but once I found the sweet spot I got three rounds within about 3/4 of an inch from just over 20 feet away in a semi rested position.

I would not recommend this Airsoft gun as an everyday shooter and there is no way you could use it in any type of Airsoft simulation as the ejected shell casings would get lost for sure and the cost to shoot the ASG CZ 75 would get very high indeed! It would be good for use in a movie or video where you wanted the realistic look of shells being ejected and did not want to use a blank gun or render the shells in post. And of course it is just really cool to have an Airsoft gun that has ejecting shells :)

Make sure to watch my Table Top Video Review for information and photos on the ASG CZ 75.

Watch my Vimeo video of the ASG CZ 75 Blowback Shell Ejecting Airsoft Pistol in action:

Buy KJWORKS KP-09 Airsoft Pistol in Canada   -   Buy Airsoft Pistols in the US

Type: Pellet air pistol.

Manufacturer: UmarexUSA.

Model: Walther CP99.

Materials: Metal and plastic (polymer) construction.

Weight: 1 pound 10.5 ounces (752 grams).

Barrel: 3.3 inches, metal rifled.

Propulsion: CO2 x 1.

Action: Semi auto, single and double action.

Ammunition Type: .177 caliber pellets

Ammunition Capacity: 8 shot rotary magazine.

FPS: 360. 

Trigger Pull: The trigger pull on the Umarex Walther CP99 is in the mid range for it's double action trigger pull with most of the effort at the beginning and middle stages as it cocks the hammer and indexes the rotary magazine, it does have a predictable release point making it easy to put pellets on target. By racking the rear slide you can put the CP99 in single action mode which makes the trigger pull much lighter and great for very accurate shots.

Accuracy: I shot this air pistol at a target from 20 feet away in a free semi rested position and it performed well getting a nice tight one inch eight shot grouping just to the left on the target. The sights can be adjusted for windage if your aim is off to one side or the other. With my preliminary Chrony Chronograph testing using 6.9 grain RWS lead pellets I got pretty close to the factory claim of 360fps with an average of right around 346 fps.

Build Quality: The Umarex Walther CP99 is a metal and polymer air gun with a good deal of metal components on the inside giving the Walther CPSport a decent overall weight and heft. It's worth mentioning that the Walther CP99 has a full size drop out magazine for holding the CO2 cartridge that gives the air gun some additional weight and functionality. The German made fit and finish is very good on the CP99 and the plastic quality is also very good.

Realism: The Umarex Walther CP99 is licensed by Walther and is based around the Walther P99. The frame is very similar to the P99 but the slide is not as accurate in terms of the real steel but you can definitely tell the Pellet shooting CP99 is a copy of a Walther P99. One of the biggest shortcomings is the safety, the real P99 does not have a safety but Umarex decided to put a rather large safety on the right hand slide area. I do however like the working de-cocker, slide catch for loading magazines and full size drop out magazine which give the Umarex CP99 a more realistic look and feel.

Purchased this gun in: The Replica Airguns Store.

Pros:

• Slide catch and de-cocker are realistic and functional.

• Rifled barrel.

• Sights are adjustable for windage.

• Slide catch and magazine release are fully functional.

• Nice full size drop out CO2 magazine.

• Good combination of power, accuracy and CO2 efficiency (I got about 100 shots from a CO2)!

• Rail for accessories.

• Walther licensing.

• German Quality.

Cons:

• Up in the higher price range.

• Double action can have some stickier shots.

• Kind of funny safety, not true to the real steel Walther P99.

• No recessed barrel

Comments:

The Umarex Walther CP99 Pellet CO2 Air Pistol is a nice step up from the Walther CPSport I reviewed earlier. The CP99 is a much more accurate looking replica of the P99 and it also has more metal parts and a single and double action trigger. These added features do come with an additional $100 price tag but in my opinion are worth it. If you're a fan of the Walther line of pistols than you should probably take a look at the Umarex Walther CP99 as it would make a great addition to your airgun collection.

Buy the Black CP99 in Canada

Buy the Black CP99 in the US

• Make sure to also checkout my Full Review for the Umarex Makarov CO2 BB Pistol

This is a kind of two-for-one'r, not only are you getting pretty much a full table top review of the KWC Makarov Airsoft BB Pistol, but you also get a comparison and revisit to the Umarex 4.5mm Steel BB shooting Makarov.

Type: Airsoft - BB Pistols.

Manufacturer: KWC - Umarex.

Model: Makarov PM.

Materials: Almost all metal.

Weight: 1 pound 12.5 ounces (808 grams) - 1 pound 9.5 ounces (724 grams).

Barrel: Metal non-rifled.

Propulsion: CO2 x 1.

Action: Semi auto non-blowback: Double action only - Single & double action.

Ammunition Type: 6mm plastic Airsoft BB's - 4.5mm steel BB's.

Ammunition Capacity: 13 round full size metal magazine -18 round metal stick magazine.

FPS: 428 - 380.

Trigger Pull: There is a lot of difference between the trigger on both of these guns, first off the Umarex Makarov has both a single and double action trigger/hammer while the KWC Makarov has a double action only trigger/hammer. Comparing the double action of both guns the definite advantage goes to the 4.5mm Steel BB shooting Umarex Makarov as it is shorter and lighter, the KWC Airsoft Makarov does not have a bad trigger but it is much longer and a bit heavier, but still very usable. The single action trigger on the Umarex Makarov is not really any lighter than when shooting in double action, it is however much shorter with a medium take-up and predictable release.

Accuracy: Both Airsoft and BB Makarov's performed very well in their shooting tests for me, they bot shot fairly well centered with the KWC Makarov getting all five shots in the black bullseye and the Umarex Makarov having a tighter group but just off to one side. This was good news since both guns do not have adjustable sights! They also scored very well in the velocity department shooting over their advertised claimed feet per second rating. The Umarex BB version shot a very respectable 390 fps while the KWC Airsoft pistol shot a very surprising 480 fps well over the claimed factory 430 fps. Both guns also shot very accurately out to ranges of 50 feet or so. From a single CO2 I was able to get 162 shots from the Umarex Makarov and 112 shots from the KWC Makarov before I noticed a significant power drop.

Build Quality: Neither one these Makarov replicas is going to win a prize for build quality, some shortcuts have been made to keep the price down on each model, but they are both built with mostly metal parts and they both performed perfectly for me during my testing. The Umarex 4.5mm Steel BB Makarov did have more moving parts while the KWC did weigh in a bit heavier, both guns had reasonable fit and finish to them.

Realism: In terms of being good Makarov replicas the pair for sure look the part, size and overall weight are very true to the original real Steel Makarov PM with the Umarex Makarov having a working slide, Makarov licensing and the ability to be field stripped. The KWC Makarov had a nicer recessed barrel and full size drop out metal magazine. I was not a big fan of the KWC screws on the right side slide or the Umarex exposed CO2 tab.

Available From: The Replica Airguns Store.

Pros:

• Umarex has the working slide.

• KWC has full size drop out magazine.

• Umarex has double and single action trigger.

• KWC has the recessed barrel.

• Umarex gets more shots per CO2.

• KWC has the higher FPS.

• Umarex can be field stripped.

• KWC has a bit more weight to it.

• Umarex is licensed

• KWC does not have ugly warning instructions.

• Both guns are mostly metal construction.

• Both guns had very good accuracy.

• Both guns have realistic working safeties

Cons:

• Umarex has the obvious CO2 tab.

• KWC has the ugly screws on the right side.

• Umarex may be a bit shiny for some.

• KWC may shoot a bit too hot for CQB Airsoft games.

• Both guns do not have adjustable sights.

Comments:

To be honest when I got the KWC Airsoft BB shooting Makarov, I was not all that awe struck, the lack of a working slide, DOA trigger and screw holes in the slide put me off just a bit. This Airsoft pistol did warm up to me a lot once I shot it, I was surprised by the very high fps and how accurate it was for such a low cost Airsoft pistol. I can really see this gun being used as a backup or sidearm in an out doors style Airsoft game where you may need to shoot targets out at range where other lower powered pistols just would not be able to get out to. The Umarex Makarov has always had a place in my heart, it is just a really good little CO2 BB pistol for the price with mostly all metal parts, a working slide, single and double action trigger and very good overall performance. In my books you can not go wrong choosing either of these Makarov replicas so choose wisely!

My Vimeo Video Table Top Comparison Review for these Makarov Air Replicas:

Buy KWC Airsoft Makarov in Canada

Buy Umarex BB Makarov in Canada   -   Buy Umarex BB Makarov in the US

This is not meant to be a full review of either the BB or Airsoft version of the Cybergun - KWC CO2 Blowback Mini UZI's but I do talk about specifications, show you around both guns, and put them both through a full Field Test so I guess in a way, perhaps it can be considered to be a full review ;)

I will list the specifications here for you but I am not going to get into details like Trigger Pull, Build Quality, Accuracy and Realism. You can check out my other video reviews for more information on the Mini UZI:

• Cybergun 4.5mm CO2 Blowback Mini UZI Review

• Cybergun - KWC Mini UZI 4.5mm BB Gun Full Auto Modification

• Cybergun Mini UZI CO2 4.5mm BB Gun Chronograph and Full Auto Shooting Test

• Dual Full Auto BB Machine Gun Destruction

Type: CO2 Blowback Machine gun.

Manufacturer: Cybergun - KWC.

Model:Mini UZU.

Materials: Metal and Polymer.

Weight: 4.8 pounds.

Barrel: Metal, non-rifled.

Propulsion: CO2 x1.

Action: BB Semi auto only - Airsoft selectable semi & full auto, single action only.

Ammunition Type: 4.5mm Steel BB - 6mm Plastic Airsoft

Ammunition Capacity: 25 - 38 rounds

FPS: 350 - 400

As I said you can check out all my other videos for info on these very accurate Mini UZI Replicas, I mainly want to go over some of the main differences and similarities for both the BB and Airsoft versions.

In terms of build quality they are made almost exactly the same and weigh in at a hefty near 5 pounds, the only differences are the inner barrel and magazines to accommodate the different sized ammo. The BB version has a 25 round single stack magazine that does not have a follower to stop the bolt from continuing to operate even after the magazine is empty. While the 6mm Airsoft version has a double stack magazine that holds 38 rounds and does have a follower to stop the bolt which can save you some unintentional wasted CO2.

The Airsoft Mini UZI version is distributed by KWC while the 4.5mm BB version is distributed by Cybergun, you will find the UZI and IWI licensing on the Cybergun 4.5mm BB version but not on the KWC 6mm Airsoft version.

Out of the box the KWC Airsoft Mini UZI is ready to go in both semi auto and full auto while the 4.5mm steel BB version will only shoot in semi auto mode, it can however be easily modded to shoot in full auto.

Both guns come in cardboard boxes with manuals, some BB's and an Allen key to tighten the CO2. The KWC Airsoft Mini UZI also comes with a handy speed loader.

There is a slight fps velocity difference between the two with the KWC Airsoft 6mm plastic rounds traveling at around 400 fps (with .20 gram BB's) and the 4.5mm Steel BB's traveling at right around 350 fps. In the field test portion I test both guns out on some water filled cans to see how each ammo type performs in terms of penetration.

Your best bet is to watch both my Table Top and Field Test Comparison Video Reviews and see for yourself how they compare!

Buy BB Mini UZI in Canada   -   Buy BB Mini UZI in the US

Buy Airsoft Mini UZI in Canada   -   Buy Airsoft Pistols in the US

Earlier this week my father called me up and asked if I wanted to head out with him to go do some hunting/shooting. He has his bear tag but for the most part, hunting with my Dad consists of driving around in his truck hoping to stumble on something since he can not walk all that far these days.

We had a great time just enjoying each others conversation and of course the beauty of Canada BC's Harrison Lake area. We also got to shoot some guns to "make sure they where sighted in and working correctly". I brought my Norinco 12 Gauge Homeland Security 780 which I needed to test out and I'm glad I did since it needs some TLC to get working smoothly. I also brought along my little Henry Lever Action 22LR which is always a blast to shoot. My Dad brought his Savage Arms 7mm Magnum just in case we did see a bear on this outing.

Long story short we didn't bring any meat back home with us but we did see some out of season doe and of course had some nice father-son time together...

One question that comes up often is the danger attached to blank gun use and the most common question I get is about the danger of shooting a blank gun at a person. Blank guns have many uses, one of which is to be used as a prop in a movie or reenactment. In this situation one may want to point and shoot a blank gun at a person to make teh scene more believable it. If the person is far enough away there is usually no cause for concern but with that said I would personally point the gun just off to one side in the event that something might come loose within the gun barrel or perhaps a fragment of something where to be fired and cause an injury to the person the gun is directed towards. With creative camera angles you shouldn't need to actually point a blank gun directly at anyone.

People also assume that because a blank gun does not actually fire a bullet that it is relatively harmless. This is not true at all, in the larger caliber blanks there is about the same amount of energy to what your would find in a real bullet, this is so the blank gun will sound about as loud as a real bullet being fired. The difference with how the energy is released in a blank round versus a real bullet is that the bullet caries most of the energy with it and when the bullet hits its intended target, the bulk of the energy is transferred to that target.

Buy ROHM  Blank Guns in Canada  -  Buy Blank Guns in the US

The energy from a blank round dissipates almost immediately after it leaves the gun barrel but the energy right at the barrel tip is very similar to that of a real bullet, especially if it has nowhere to go but directly into an object. So yes a blank gun round can be lethal at very close ranges and unfortunately several people have paid with their lives finding this out for themselves.

With this newfound information about blank gun danger, some people might say... get rid of these dangers to society! Before we head in that direction think about how many other non vital things we have in our lives that I would have to say have claimed way more lives than blank guns could even come close to: Off-road pleasure vehicles, Skydiving, Skying, Pools, Real Guns to name a few! Blank guns also serve very useful purposes like being used to signal a warning or distress, send out flares, ward off wild animals, train people on how to use a real gun, and of course dog training. I am sure the good outweighs the bad here.

That's enough politics for now, juts watch the video and see for yourself why you should not point a blank gun at anyone, especially if the person is very close in proximity to you!

Buy ROHM  Blank Guns in Canada  -  Buy Blank Guns in the US

Type: Blank Pistols.

Manufacturer:ROHM (RÖHM).

Model:RG-300, RG 3

Materials: Mostly Metal.

Weight: 1 / .75 pounds.

Barrel: Front firing semi plugged.

Propulsion: Gun powder.

Action: Double action only.

Ammunition Type:.22 Caliber Crimped.

Ammunition Capacity: 10 / 6 rounds.

FPS: N/A.

Trigger Pull: The trigger pull on the RG-300 and RG 3 is double action only and a bit on the heavy side so you will need to hold the gun firm and apply an even and long pull to fire the these blank guns, after a few shots you get the hang of it. If you do not pull the trigger the entire way back until the hammer releases, the shot will not fire but the blank will index and move onto the next round so you may have an unused blank when you pull out the magazine.

Accuracy: NA.

Build Quality: The overall build quality for the ROHM RG-300 and RG 3 blank pistols is very good, being German made they are built to last and the fit and finish is very good. The only real plastic would be the grips on both models which is to be expected. Both guns worked perfectly for me during my testing and with the exception of a bit of a heavy DOA trigger pull since the trigger first has to index the magazine and then fire the round.

Realism: The ROHM RG-300 and ROHM RG 3 are not exact replicas of any given guns in production as this would make importing them into Canada even more difficult. The ROHM RG-300 does however share some similarities in looks to that of a Sig Sauer but in a much smaller form factor !

Purchase from: The Replica Airguns Canada Store.

Pros:

• German made quality, materials fit and finish is all excellent.

• Almost all metal with some reenforced steel parts.

• Very safe double action triggers, will not accidentally misfire on you.

• Both are front firing.

• Come with flare adaptors and cleaning rods.

• Available for import into Canada.

Cons:

• Not actual exact replicas of any specific guns in production.

• Double action trigger pull is a bit tough and takes some getting used to.

• Expensive due to them being harder to get and in high demand in Canada.

Comments:

One nice point with the .22 caliber blank shooters is the lower cost to shoot them, .22 caliber crimped blanks work out to be much cheaper than the 8mm &  9mm P.A.K. or .380 crimped blanks. Sure they are a bit quieter but louder than you might think, especially when coming out of a short barrel. Another selling point is how compact both of these guns really are which makes them easy to pack around if you want to take one with you on a hike or outing as a deterrent for any wildlife that may get a bit too close to you. The RG-300 and RG 3 are two very nice additions to the ROHM blank guns we sell in the Canada Replica Airguns Store.

Buy ROHM Blank Pistols in Canada

I don't often get to shoot my airguns out at the 100 foot mark but I purchased my Sheridan Silver Streak .20 Caliber Multi Pump Pellet Rifle mainly to shoot up to and even past this fairly distant range as the Silver Streak is my new vermin gun for pests around the farm. I get a lot of Crows that to be honest are just feathered bullies that pick on all the other friendly birds on the farm, they have also been known to get into my garbage and even attack the Eagles and Hawks in the area. Flying Rats I like to call them.

In this Field test Shooting video I test out my brand new Sheridan Silver Streak on the Chronograph to see just how powerful it really is not just at the maximum 8 pumps but also at 3 and 5 pumps. I was actually very surprised at the very decent power I got from only 3 pumps (460 fps), you could easily take out a small rat with the 14.3 grain .20 caliber lead pellets I was using for my Chrony test.  At 5 pumps I gained close to another 100 fps and at 8 pumps I maxed out at just a hair under 640 fps respectively. With the 14.3 grain pellets I was using this worked out to right around 13 foot pounds of energy. (My Sheridan was purchased using a PAL)

I also shot my Sheridan Silver Streak .20 Caliber Pellet Rifle at a target setup 100 feet or just over 30 yards away and was able to get what I felt was a nice 1.5 inch 5 shot grouping. 4 of the 5 pellets where all within 1 inch of each other with my first shot being a bit lower and to the right of the rest spreading the group out to about 1.5 inches. Keep in mind I was also a bit winded from all the pumping and I could feel and see my heartbeat in my 9 power Bushnell scope making my crosshairs bob back and forth ever so slightly.

I have not shot my Sheridan Silver Streak all that much and plan to hone my skills further so when the time comes I will be ready for them pesky crows.

Stay tuned for my future Table Top review of my Sheridan Silver Streak, for now you can checkout my Preview video that has some preliminary info.

For the most part, this video is to test out some cameras and using them all together in a multi-camera scenario. I wanted to see how many camera angles I could shoot at one time and see how they would all work together when editing the video.

Cameras used:

• My new Pivothead Recon Camera Glasses.

• Sony HDR-AS15 Action Cam.

• Drift HD170 Point of View Camera.

• Nikon 1 with 10mm fixed lens.

• Casio TRYX.

• *All cameras where shooting in 1080p for this video.

I hope to use camera setups like this in the future, maybe not all at once but at least a couple at a time to give you some viewing options.

I picked out my WE SCAR GBB Airsoft Rifle for this test as it had a lot of mounting points and the Gas Blow Back makes for some great video action. Unfortunately My WE SCAR was not working at 100% but I still think I was able to pull off this test video either way.

Watch my Multi-Camera-Angle Test Video shooting the WE SCAR GBB AIrsoft Rifle:

Buy Airsoft rifles in Canada   -   Buy Airsoft rifles in the US