Here is my official Field Test Shooting Video Review for my Daisy Winchester Model 11 CO2 Blowback BB Pistol. Make sure to checkout my previous Table Top Review for more details on the Winchester Model 11 1911 CO2 4.5mm BB version where I also did a pre-test showing similar results.
My 5 shot Chronograph test resulted in a bit lower than previously tested 339 average fps while my accuracy test shot from 20 feet out in a semi rested position got six shots right in the 1.5 inch bullseye with 4 shots coming out a bit, 2 of which spread the group out to about a 3 inch grouping in total. So in terms of shot placement you could say the Daisy Winchester 1911 4.5mm BB Pistol shot very well centered. Agin this time around I got 6 full magazines but had to manually clock teh hammer back on some of the last magazines end shots, power did seem OK even when manually cocking the hammer.
Overall, the Daisy Model 11 4.5mm BB Pistol is nice pretty much all metal low-cost CO2 Blowback BB pistol with good overall performance. This one looks the part of a 1911 even though it may not function 100%. If your OK with close and want to save a few bucks, then teh Daisy Winchester Model 11 may be for you, if you don't mind spending a bit more to get a BB gun as close to a real 1911 A1 as possible than take a look at the KWC/Cybergun Tanfoglio Model 1911 full blowback BB Pistol and Airsoft Pistol versions.
Here is my official Field Test Shooting Video Review for my KWC Sigma SW40F CO2 Blowback BB Pistol. Make sure to checkout my previous Table Top Review for more details on the KWC SW40F 4.5mm BB version where I also did a pre-test showing some similar results.
My 5 shot Chronograph test resulted in a somewhat expected 285 average fps while my accuracy test shot from 20 feet out in a semi rested position received a slightly wider 3 inch group this time but with most shots being within 1 inch of each other. In terms of shot placement the KWC SW40F 4.5mm BB Pistol shot very well centered but just slightly low. I also only got 2 full magazines this time around so don't expect a lot of shots per CO2 with this 4.5mm BB pistol.
Overall, the KWC SW40F 4.5mm BB Pistol is a really fun gun to shoot with a very crisp heavy slide that gives a nice firm blowback snap to it. It is one of the nicer sounding slides with a less tinny sound than most. The fps and shots per CO2 is a bit low but other than that performance is very good, you will have no problem nocking down cans and acquiring other miscellaneous targets.
Trigger Pull: The trigger pull on the Daisy Winchester Model 11 is very nice, just about the perfect pull weight, not too heavy or too light, it has next to no take-up at all and a nice predictable release point. As is traditional with a 1911 styled pistol, the trigger is single action only so you will need to either pull the hammer back or rack the slide for the first shot, with subsequent shots you will not have to do this as the blowback action cocks the hammer for single action shooting. If your CO2 is very low, the blowback may not be adequate enough to cock the hammer so you can do this manually to get a few extra shots out of the Daisy Model 11.
Accuracy: When I shot the Winchester Model 11 from 20 feet out in a semi rested position, I was able to get some decent results. I placed 10 rounds within about a 2 group and the shot placement was very well centered, just a slight bit to the left. I did get a couple of stragglers that spread the group out just a bit larger but not too much. I did also get right around 350-360 fps on my chronograph on this not so warm day. We will have to see what my dedicated field test results yield for this BB pistol.
Build Quality: The Daisy Model 11 (1911) is made in Japan and has a nice overall finish to it. Other than the plastic magazine and grips it is an all metal gun so the materials used are good. The slide does have a bit of wiggle play in it but so do many blowback air pistols, perhaps to reduce some friction as the slide springs on these guns are not overly heavy. The paint used seems to be holding up very well and looks good, I did notice a molding seem that runs down the underside of the slide and along the trigger guard.
Realism: The Daisy Winchester Model 11 is a replica of the real steel 1911 A1 style 45 auto. It does have the Winchester licensing on it but I am not sure if there is an exact Winchester 1911 this gun is made to replicate. For the most part it looks and functions very similar to a real 1911 with a few exceptions like the lack of a working grip safety, a rather strange two stage safety and also the stick styled smaller magazine. This blowback air pistol can not be field striped conventionally either. I do like the true single action trigger and open ejection port.
Lots of metal in this airgun and good weight to it.
Good overall looking replica of a real 1911.
Reasonably decent blowback feel.
Mid range fps and shots per CO2.
Very nice true single action trigger.
Shots where well centered and got decent accuracy.
Markings and instructions on gun are color matched.
Solid CO2 tightening system, seems to work well once you get the hang of it.
Not bad at all for the lower price point.
Like the open ejection port.
Made in Japan.
Cons:
Kind of funny safety setup, it is redundant?
Has a plastic magazine, would have been nice in metal.
Back strap safety does not actually work but it does move.
Says "clip" instead of "magazine" on gun.
Comments:
I know some people have been hating on this gun for a couple of reason so let's get them out of the way... Yes it has a weird safety setup and I can not tell you why Daisy did this, perhaps they wanted it to be "more safe"? As a 1911 trainer you will have to adapt how you take this gun off of safety over a traditional 1911 setup. The magazine is plastic, not a biggie, if it breaks on you get another one. It's not full blowback like the Cybergun/KWC Tanfoglio 1911, this is true but you do get higher fps and more shots per CO2 out of it because of this. And yes Daisy uses the word "Clip"on the gun instead of the correct term "Magazine". Honestly, the Daisy WInchester Model 11 is a nice overall BB gun and the price point is pretty low for what you get. It looks really good overall and shoots nicely with enough blowback to give you some recoil feel and allow for true single action shooting. You also get decent fps and a good amount of shots from a single CO2 cartridge so stop complaining and just enjoy this gun for what it is!
My Vimeo Table Top Review of the Daisy Winchester Model 11 Blowback CO2 BB Pistol:
Trigger Pull: The trigger pull on the KWC Sigma SW40F CO2 Blowback BB Pistol is single action only which generally produces a very light trigger, on the SW40F it is a bit firmer than most single actions but still decent with a short take-up and firm release. You will need to pull the slide back (which also chambers your first round) to cock the internal hammer, after which subsequent shots you will not have to pull the slide back as the blowback action does this for you.
Accuracy: When I shot the KWC Sigma SW40F from 20 feet out in semi rested position I was able to get nice clean results. I placed 10 rounds within about 2 inches with the shot placement being very well centered. The KWC S&W Sigma SW40F seemed to keep the rounds tighter from top to bottom over side to side for me. I also noticed when I field stripped this gun that there is a built in hop-up (rubber bar) that sits inside the barrel, this will produce some back spin which will keep the BB's trajectory a bit flatter when shooting further out and is also probably there to stop BB's from rolling out of the barrel once chambered.
Build Quality: The build quality is about the same as all other KWC guns, tolerances seem tight and everything is working as it should, you will get some wear marks (paint wear) on the high spots over time which is normal on just about any (type of gun, real or air) but what I like about the SW40F is that the barrel is polished and since this is the first area to lose paint, it really does not matter since no paint is on the barrel.
Realism: The KWC Sigma SW40F CO2 Blowback BB Pistol is a replica of the real steel S&W Sigma with the exception of the licensing and it really is a bang on Replica, you can field strip this gun exactly like a real Smith & Wesson Sigma. All the mechanical parts work just the same and I like the fact that without the licensing, this gun is very clean looking with no obtrusive warning instructions on it.
Lots of metal in this gun with very good weight to it.
Very accurate S&W Sigma replica.
Heavy crisp blowback feel.
Predictable single action trigger.
Shots where well centered, got good accuracy.
White dot sights for quick target acquisition.
No ugly warning markings.
Full size drop out magazine holds BB's and CO2.
Like the polished barrel and ejection port.
Fully field strip-able.
Cons:
I only got two magazines in my pre-test for some reason?
FPS is not super high?
A bit finicky when loading BB's
Comments:
Just like my Airsoft review of the KWC Sigma SW40F, this blowback Air Pistol was a lot of fun to shoot, with it's super snappy heavy slide and ultra realistic shooting characteristics. It did seem to go through a lot of CO2 very quickly which is not uncommon for this style of full blowback heavy slided airgun, and to be honest I don't really mind since it shot well, felt good in the hand and backs it up with great looks. And heck it's still so much cheaper to shoot than a real 9mm hand gun ;) For those of you looking for something that is similar to a Glock in terms of looks and operation, the KWC Sigma BB or Airsoft pistol may be your only real option here in North America now that the Umarex SA177 is history.
My Vimeo Table Top Review of the KWC Sigma SW40F Blowback CO2 BB Pistol:
Trigger Pull: The trigger pull on the RG-88 and RG-59 in single action is very light with the RG-59 having virtually no take up at all while the RG-88 has some take up but then a noticeable and predictable release point. Both guns have medium to heavy yet smooth double action triggers.
Accuracy: NA.
Build Quality: The overall build quality for the ROHM RG-88 and RG-59 blank guns is excellent, being German made they are built to last and the fit and finish is very good. There are steel parts where they need to be like in the barrel, pins, screws and reenforcing parts, the rest of the gun is generally made out of a zinc metal with only the grips being plastic.
Realism: The ROHM RG-88 and ROHM RG-59 are not exact replicas of any given guns in production as this would make importing them into Canada even more difficult, but they do share similarities with some real guns in production. The RG-88 semi auto looks to be based around a Walther PPK design while the RG-59 has that Smith & Wesson Snub Nosed Revolver look to it. As for looking like and working like real guns, they do this very well, with the exception of the dangerous bullet coming out of the barrel!
German made quality, materials fit and finish is all excellent.
Almost all metal with some reenforced steel parts.
Nice light single action triggers on both guns with double action ability wehn needed.
Both are front firing with semi plugged barrels.
Come with flare adaptors and cleaning rods.
Seem to be some of the only blank guns we can get here in Canada right now.
Cons:
Not actual exact replicas of any specific guns in production.
The RG-59 only works with the .380 crimped, 9mm P.A.K. balnks are a bit too long.
Expensive due to them being harder to get and in high demand in Canada.
Comments:
As with pretty much all blank guns, they are mostly for show so it all comes down to how do they look and do they go bang when they are supposed to! In both cases they get top marks. Both the RG-88 semi auto and RG-59 revolver feel solid and the mechanical parts are tight and smooth giving a confident feeling when holding them. I like the larger caliber blanks over the .22 crimped blanks as they have a bigger bang but they will set you back in the cost department a bit more as the price for 9mm P.A.K. and .380 blanks will be a lot more than .22 crimped so keep this in mind when choosing a blank gun. If you're looking for a well made and dependable blank pistol then you really can not go wrong with any of the ROHM blank guns we sell in the Canada Replica Airguns Store.
My Vimeo Full Video Review for the ROHM RG-88 and RG59 Blank Pistols:
I usually do my Table Top Video Review first but this time around I did my Field Test Video Review first since I was all setup checking out a couple other guns at the time. When I do my detailed Table Top Video Review for the Cybgergun Sig Suer P226, I'll post the link here so stay tuned. If you have not already checked out my Barrel Mod Video for this same gun then check that video out where I remover the extended orange portion of the metal barrel and make the barrel flush with the end of the slide which is how the real steel version was originally made.
Getting back to the Cybergun Sig Sauer P226 GBB blowback Airsoft Pistol field test, as per usual I test this Airsoft semi auto gas blowback pistol on the Chronograph to see what kind of real world velocity I get and since I had some Green Gas on hand, I used it for this part of the review and got an average of 315 fps with a six shot string.
I also stepped back 20 feet and shot 10 times at my stationary target using a semi rested position (sand bag up front and kneeling in the back). Even though the Sig Sauer P226 shot a bit low I did get about a 1.25 inch group with the exception of one flyer that hooked down just a bit making the 10 shot group a bit wider at just under 2 inches. The low shot placement may have been caused by my barrel mod but since I did not do a before and after test, I can not say for sure?
Make sure to watch my YouTube Video of this Field Test as it also includes some nice slow-motion of the slide blowback at both 400 and 1200 frames per second.
Watch my full Video Field Test Shooting Vimeo Video below:
My 5 shot Chronograph test resulted in a lower than expected 308 average fps while my accuracy test shot from 20 feet out in a semi rested position this time received a just over 2 inch group but with most shots being within 1 inch, I have found with Airsoft guns that there can be some floaters perhaps due to inconsistencies with some of the ammo. In terms of shot placement the KJWORKS KP-05 HI-CAPA 1911 shot very well centered only being just slightly high and to the left but only marginally. I was also able to get 2 full magazines plus another half mag this time around so just over 60 shots with the KP-05.
KJWorks KP-05 1911 HI-CAPA Airsoft Pistol although not shooting as hard as I though it would still performed great for me and would make a great field gun as it performs very well and has a nice high capacity magazine which would come in handy in the heat of battle.
My 5 shot Chronograph test resulted in a very respectable 366 average fps while my accuracy test shot from 20 feet out in a semi rested position this time around came in a bit higher than my pre test right at around 2 inches. Several of the shots hit right on top of each other. In terms of shot placement the KJWorks KP-09 CZ 75 shot fairly well centered but just a bit high and a tad to the left. I was also able to again get 3 full magazines or around 75 shots out of this heavy blowback Airsoft pistol.
KJWorks KP-09 CZ 75 Airsoft Pistol really has a lot going for it, it's a great Replica of a real steel CZ 75 with a very nice single action trigger, it has great snappy full blowback with excellent fps and accuracy and it even gets a solid 75 shots out of a single CO2 which is very good for this style of full blowback gun.
I have not done my official Table Top and Shooting Reviews for the Gas Blowback Airsoft Cybergun Sig Sauer P226 but I really wanted to cut off the ugly orange painted barrel tip, it was kind of driving me crazy! keep in mind here in Canada we are not required to have orange tips on our Airsoft guns, most of the all metal or all black Airsoft guns imported these days fall into the "airgun uncontrolled firearms" category. If you live in the US or other parts of the world you could be breaking the law if you do this mod so be warned...
Your best best is to simply watch my Vimeo Video as I show you exactly how I removed the orange painted portion of the metal barrel using a hack saw, file, vice and some sand paper. All in all it was not too difficult and only took about 15 minutes to complete...
Trigger Pull: The trigger pull on the KJWORKS KP-05 is what you would expect from a true 1911 single action only trigger, it has very little take up with a smooth crisp and light release to it.
Accuracy: I shot the KJWORKS KP-05 from 20 feet out in semi rested position and got very good test results. I was able to place 10 rounds in under 1.5 inches and getting four shots right in the bullseye making the shot placement very good even without adjusting the sights (which can be adjusted for windage). The KJWORKS HP-05 1911 styled HI-CAPA Airsoft Replica shot right around 300 fps range while conducting my 5 shot average chrony testing which was surprisingly low for the CO2 magazine version, this may have been a temperature or CO2 related condition, when I conduct my full Field Test Shooting Review, I will review this and see if we can do better? I also got two full 30 round magazines worth of shots which is what you would expect from this style of full heavy blowback airsoft pistol.
Build Quality: I am extremely impressed with the build quality of all the KJWORKS Airsoft guns so far, the fit and finish is the best around on any of my guns including my 4.5mm steel BB shooters. After shooting several magazines worth of BB's, areas that are painted like the metal friction areas show very light wear which is rarely the case with metal built blowback airguns. Again the tolerances between the moving parts like the slide and frame are very tight showing excellent workmanship and machining from KJWORKS.
Realism: The KJWORKS KP-05 6mm Airsoft pistol is a replica of a High Capacity styled tactical 1911 45 Auto and is a great looking and functioning replica. You will not find any actual licensing on this pistol and the CO2 magazine does stick out a bit to accommodate the 12 gram CO2 but other than that this Airsoft pistol looks and works near exactly like a real 1911 tactical semi auto and is fully field strip-able. I really like the updated more tactical add ons like the tactical rail, machined trigger and hammer, white dot adjustable sights, wrap around grips and ambidextrous safety.
All metal pistol with good overall realistic weight to it.
Full heavy blowback operation.
Typical KJWORKS excellent fit and finish.
High capacity magazine 30 rounds.
Very good accuracy and well centered on target.
Nice replica of a High Capacity Tactical 1911 styled pistol.
I like the stainless highlights and ambidextrous safety and Rail for accessories.
Fully field strip-able.
Cons:
Shot a bit low Feet Per Second for me - should do better?
CO2 magazine is long to accommodate the 12 gram CO2.
Slide is heavy enough but seems to be a bit sluggish which is kind of a 1911 trademark so that can be taken as good or bad.
Comments:
The KJWORKS KP-05 1911HI-CAPA is another excellent full blowback Airsoft pistol from KJWORKS. The HP-05 is a classic upgraded more modernized version of the 1911 semi auto pistol which is a great foundation to build any pistol from. I found the CO2 usage to be decent on the KP-05 but felt that I should have been able to get more fps out of this pistol, I will be testing the KJWORKS KP-05 again and hope to see some better results in this area. With that aside, the KP-05 1911 HI-CAPA is a great shooter and as is, with its high capacity magazine would be a perfect sidearm for any Airsoft related squirmish or even just for honing up your shooting skills when getting to the gun range is not an option.
Trigger Pull: The trigger pull on the KJWORKS KP-09 CZ 75 Airsoft Replica is surprisingly light in single action but incredibly sticky at first in double action, with that said you really will not be shooting very often in double action unless you happen to de-cock the gun for some reason, at least you have the ability to shoot with the hammer down in double action when required. In signal action it took me a bit to get used to the very light trigger pull as I was letting some shots go off early.
Accuracy: I shot the KJWORKS KP-09 from 20 feet out in semi rested position and got very satisfactory results. I was able to place 10 rounds under 2 inches almost getting a 1 inch group with the exception of one flyer. Shot placement was also well centered but just a bit high which could easily be corrected by adjusting my aim point just a bit down. The KJWORKS CZ 75 Airsoft Replica shot right around the 360 fps range while conducting my 5 shot average chrony testing which is right where this gun is supposed to be. I also got three full 24 round magazines worth of shots with a bit of CO2 left over for a partial mag, so this gun can easily get 75 shots out of a 12 gram CO2 - not bad at all for this style of full heavy blowback airsoft design.
Build Quality: I am extremely impressed with the build quality of pretty much all the KJWORKS Airsoft guns, the fit and finish is the best I have seen on any of my guns including my 4.5mm steel BB shooters. Even after shooting several magazines worth of BB's, the painted metal friction areas show very light wear which is not always the case with metal built blowback airguns. (there was some wear present within the ejection port but this is common even with real steel guns as metal on metal will wear down the finish). The tolerances between the moving parts like the slide and frame are very tight showing excellent workmanship and machining.
Realism: The KJWORKS KP-09 6mm Airsoft pistol is a replica of the real steel CZ 75 and is a great looking and functioning copy. You will not find actual licensing on this version and the CO2 magazine does stick out a bit to accommodate the 12 gram CO2 but other than that this Airsoft pistol looks and works near exactly like the real mccoy and is full field strip-able. Even the safety operates just the same with safety available on half cock and full cock only.
All metal pistol with good overall realistic weight to it.
Very crisp and firm full blowback operation.
Excellent fit and finish - best I have seen.
Excellent fps and CO2 efficiency (three plus full 24 round magazines)
Good accuracy and well centered on target.
Very believable working replica of the real steel CZ 75.
Fully field strip-able.
Cons:
Does not have official CZ 75 licensing.
CO2 magazine is long to accommodate the 12 gram CO2.
Did get some finish wear in the ejection port area.
Comments:
The KP-09 CZ 75 is another wonderful full blowback Airsoft pistol from KJWORKS. The CZ 75 is a classic semi auto pistol and deserves the attention to detail the KJWORKS version demonstrates. I found the CO2 usage to be very good on the KP-09 considering the rather high 360+ fps I was abel to get with it. Top this off with high marks in the accuracy department and you have a real winner here. So if you're looking for a quality Airsoft Replica of the classic CZ 75 that shoots straight and hard and looks and operates just like the real steel version then the KJWORKS KP-09 should just do the trick for you.
Here is my official Field Test Shooting Video Review for my Umarex Walther P38 CO2 Blowback BB Pistol. As with my original Table Top Review, I shot pretty close to the manufacturers claimed 400 fps getting a 5 shot average of 392 fps.
And the same can be said with my accuracy pre test, both tests came in just about the same with an approximate 2 inch very well centered grouping shooting at the target from 20 feet out in a semi rested position. I even got 8 of the 10 rounds right in the 1.5 inch bullseye with only two rounds coming just outside. Good thing it was already pre sighted as the sight on the Umarex Walther P38 can not be adjusted. You can also expect to get a good 100 shots from a single CO2. I would also like to point out that even thought he slide is fairly light and the blowback is not full, The P38 still has a nice blowback snap to it.
The only real negative point I can make about the Umarex Walther P38 Replica Air Pistol is the somewhat medium to heavy trigger pull which I found a bit surprising since it has a single action only trigger? This was offset by the fact that The Umarex P38 had such good combined accuracy, power and CO2 efficiency wrapped up in a very believable Walther P38 Replica.
Here is my official Field Test Shooting Video Review for my KWC M1911 Model A1 TAC CO2 Blowback BB Pistol. Interestingly enough, this time around I got a bit lower average feet per second rating from this air gun at right around 290 fps as compared to the pre-test I did during my Table Top Review (shot closer to 310 average fps)? Both days the temperature was about the same and the CO2 used on both occasions was the same brand and where unused. Just goes to show you that these guns sometimes have a mind of their own...
At least the accuracy portion came in just about the same with an approximate 2 inch grouping shooting at the target from 20 feet out in a semi rested position. I did shoot a bit to the left and a bit low which I could adjust from left to right but since there is only a windage adjustment I would have to sight a bit up to hit the bullseye with the KWC M1911 Model A1 TAC. This time around I also got 4 magazine worth of shots as I slowed things down a bit and took my time and juts like last time I had no problems or malfunctions with my KWC M1911 Model A1 TAC.
The best part about shooting the KWC M1911 Model A1 TAC CO2 Air Pistol is it's beautiful single action 1911 styled trigger and nice heavy full blowback action, making this gun a great economical trainer if you own the real steel version or perhaps just want to feel like you do!
Trigger Pull: The trigger pull on the Umarex Walther P38 CO2 Blowback BB Replica is a bit heavier than I expected it would be as it is a single action only trigger. There is a lot of take up initially but once you hit the release area, the release point is what I would describe as a medium to heavy pull for a single action shooter. With that said it did not seem to effect the accuracy at all and I was able to rifle off quick shots fairly easily.
Accuracy: I shot the Umarex Walther P38 BB Pistol at a target from 20 feet away in a semi rested position, and it performed very good getting just under a 2 inch grouping and very well centered on the target. The sights are not adjustable so adjusting the Umarex Walther P38 would not be possible except by using a modified aim point! My initial Chrony testing puts this BB shooter just under the 400 claimed fps range right in the 380 area which is not bad considering the rather cold day I was shooting on. I also managed to get five magazines worth of shots which is a vert respectable 100 shots per CO2.
Build Quality: The Umarex Walther P38 CO2 Blowback BB Pistol is almost all metal with the exception of the grips which is great to see! I found the fit and finish to also be very good with a nice Semi Gloss paint job that should wear well over time. Interestingly enough the Umarex Walther P38 has a removable barrel so I am assuming that perhaps Umarex will introduce some more barrel length options at some point?
Realism: The Umarex Walther P38 CO2 Blowback BB Airgun is very close to the real steel Walther P38 and even has the Walther P38 licensing on it. What I was really impressed with was the fact that all the mechanical parts do exactly what they would do on the real gun. On some other guns these parts are merely for show and moulded into the gun. The Blowback action, hidden CO2 screw and recessed barrel all help to make this Walther P38 Replica very believable!
Replicates the real steel version fairly well with all the working parts pretty much doing what they did on the original.
Nice that it has blowback while still gets decent fps and shots per CO2.
The Blowback had more feedback then I thought it would.
Mine seemed to be very well centered on target and got a good tight grouping.
CO2 is very well hidden in the handle.
Good weight fit and finish to it.
Glad to see a World War BB replica pistol!
Almost all metal.
Cons:
Had a rather heavy trigger for a single action only gun.
CO2 screw may be a bit hard to tighten for people with sausage fingers.
Some people may not like the high gloss finish.
Comments:
There are few older Classic Airguns out there, especially ones from the World War era! On that topic I would also like to see some old Single Action Army Cowboy Revolvers start to show up in the Replica Airgun market! As I was saying it is nice to see this Classic Walther P38 show up in what seems to be a sea of modern styled airgun replicas. Umarex not only came out with a BB shooting Walther P38, they made it very believable in terms of operation, while maintaining good overall airgun performance. I hope this is a trend that continues in the direction of companies offering more quality airgun replicas of guns from the past.
Ammunition Capacity: 18 round full size metal magazine.
FPS: 320.
Trigger Pull: The trigger pull on the KWC M1911 A1 Tac blowback BB Pistol is exactly what you would expect from a true single action 1911 styled pistol. It has a short take up and then a nice light and crisp pull to it. Because of the similar mechanics not only to the trigger but other aspects of this gun, it would make an awesome low cost trainer to be used when your real 1911 can not be.
Accuracy: I shot the KWC M1911 A1 Tac BB gun at a target from 20 feet away in a semi rested position, and it performed well getting a 2 inch grouping just a bit off center of the target. The sights are adjustable for windage so zeroing the KWC M1911 A1 Tac in would not be much of a problem! My initial Chrony testing puts this gun right in the 300-320 fps range which is just fine for this style of heavy full realistic blowback action BB shooter. I also managed to get three very good magazine worth of shots with some extra CO2 left for a potential 4th magazine. If you slow your shooting down and let the gun and CO2 warm up between magazines you can get 4 magazines with this gun for sure.
Build Quality: KWC did a great job with the KWC M1911 A1 Tac. The quality and build characteristics may even be just a bit better than my other KWC/Cybergun blowback air pistols. Everything that should be metal is the same on this as the original, the slide and barrel wiggle are minimal and the finish seems to be wearing fairly well on this KWC airgun. I do expect over time fore some of the finish to wear off on the high points but this can also give the gun some character ;)
Realism: The KWC M1911 A1 Tac BB airgun is as close as you can get to the real steel 1911 A1 45 auto but with an obvious more modern Tactical look to it, the Tactical version has the addition of a: Tac style trigger and hammer, textured grips, ambidextrous safety, adjustable white dot sights, rail for accessories. This gun is nearly all metal with very heavy blowback making it feel real to hold in the hand and shoot.
All metal construction - Good weight and solid feeling gun.
Nice heavy blowback action.
Very Accurate 1911 A1 styled replica in many way.
True 1911 Single action trigger, excellent pull, very smooth and light.
Accurate trigger design and working grip safety.
Decent accuracy, not too bad amount off shots for this style of gun about 3+ good magazines.
All metal full size dropout magazine.
Love the upgraded Tactical features (Tac style trigger and hammer, textured grips, ambidextrous safety, adjustable white dot sights, rail for accessories)
Cons:
Sacrifice fps and shots per CO2 because of the heavy blowback but worth it.
Finish on the Cybergun and KWC guns can ware off on the high points a bit but some people like this look.
Comments:
I love my Cybergun Tanfoglio Witness 1911 as do many of you based on the amount of sales we have had on that unit! After all who does not appreciate such an accurate replica of the Classic Colt 1911 A1 45 auto? The only problem with the classic 1911 is that it is missing a few of todays more modern features and that's what is so nice abut the new KWC M1911 A1 Tac BB Pistol, it takes an all ready great design and makes it even better by adding the Tac style trigger and hammer, textured grips, ambidextrous safety, adjustable white dot sights and rail for add on accessories. So if you're a 1911 fan looking for as close as you can get to the real steel in a more modern version than look no further, this is it!
This is the official Field Shooting Test Video Review for the ASG Bersa BP9CC CO2 Blowback BB Pistol. If you haven't checked out my Table top Video Review for the ASG Bersa BP9CC, make sure to do so as I have some more photos there along with the specifications and details including the Pros & Cons for the this very realistic Bersa airgun replica!
In this part of the review I test the ASG Bersa BP9CC 4.5mm BB Pistol using my Chronograph to see what the 5 shot feet per second average is using a fully charged CO2 cartridge. Even on this rather cold day, the ASG Bersa BP9CC BB Airgun performed even above the factory claimed 350 fps and was very consistent, within a few fps for each shot averaging 366 fps.
I also take the ASG Bersa BP9CC CO2 Blowback BB Pistol back 20 feet and shoot it at a target using a semi rested position (sand bag up front, kneeling in the back) and shoot 10 rounds into the target getting a not too bad 2 inch grouping with this small short barreled blowback airgun. Near the end of the video I use my high speed slow motion camera setting to capture the blowback in both 400 and 1200 frames per second so you can see for yourself how the blowback action works.
All in all the ASG Bersa BP9CC CO2 Blowback BB Pistol performed very well and had no malfunctions, the accuracy was respectable for an action blowback pistol like this one and the same goes for the fps being that the ASG Bersa has both blowback and a short barrel. I was also very happy with the CO2 efficiency getting close to 120 shots (6 magazines) out of a single 12 gram CO2 cartridge.
If you're looking for a compact action BB pistol with great looks, realism and performance, make sure to checkout the ASG Bersa BP9CC CO2 Blowback 4.5mm BB Pistol!
By the way in this video I also test out my new Liquid Image Impact Series Camera Goggles to see how they work to protect my eyes while recording video in first person view.
Watch my Field Test Shooting Vimeo Video Review for the ASG Bersa BP9CC CO2 Air Pistol:
In this part of the review I test the HK G36 KV AEG Rifle using my Chronograph to see what the 5 shot feet per second average is using fully charged batteries. I got pretty much right bang on to the factory claimed 450 fps using .20 gram 6mm plastic Airsoft BB's and consistency was within a few fps for each shot.
I also take the Umarex HK G36 KV AEG Blowback (EBB) Airsoft Rifle back 30 feet and shoot it at a target using a semi rested position (sand bag up front, standing in the back) and shoot in both semi auto and full auto, there really was no real difference in accuracy using both selections, I think the built in magnified scope helped out here to get a very tight 1.5 inch group shooting in semi and full auto.
So far out of all my AEG rifles I would have to say the Umarex HK G36 KV (EBB) performed the best getting very consistent and high fps and tight groupings in both semi and full auto even using light weight .20 gram BB's.
Watch my Field Test Shooting Vimeo Video Review for the Umarex HK G36 KV AEG Blowback Airsoft Rifle:
In this part of the review I test the Smith & Wesson 357 CO2 Pellet Revolver using my Chronograph to see what the 5 shot feet per second average is using a brand new CO2. I got pretty close to the factory (even a bit over) claimed 425 fps using RWS 7 grain lead pellets on this rather cold day so you can expect better fps on a nice warm summer day.
I also take the Smith & Wesson 357 686 CO2 Pellet Revolver back 30 feet and shoot it at a target using a semi rested position (sand bag up front, standing in the back) and again although I did not get teh same half inch grouping I got in my preliminary testing, I did manage to get a nice tight grouping , keep in mind the Umarex Smith & Wesson 357 is an action shooter but is capable of target pistol like accuracy.
All in all the Umarex Smith & Wesson 357 686 CO2 Pellet Revolver performed very well. That said I was able to get tighter groups and higher fps so expect this Umarex high grade CO2 pistol to perform very well for you.
Watch my Field Test Shooting Vimeo Video Review for the Umarex Smith & Wesson 357 686:
This is the official Field Test or Shooting Video Review for the G&G Xtreme 45 CO2 Blowback Airsoft Pistol. If you haven't checked out my Table top Video Review for the G&G Xtreme 45, make sure to do so as I have some more photos there and also all the specifications and details including the Pros & Cons for the G&G Xtreme 45.
In this part of the review I test the G&G Xtreme 45 CO2 Blowback Airsoft Pistol using my Chronograph to see what the 5 shot feet per second average is using a mostly brand new CO2. I got pretty close to 400 fps which is not bad considering the very cold day and the fact that I had to reset my Chronograph and missed the most powerful first several shots.
I also take the G&G Xtreme 45 back 30 feet and shoot it at a target using a semi rested position (sand bag up front, standing in the back) and again I was plagued by technical difficulties and had to redo this part of the test as one of my cameras was not working. I did get a nice 2 inch 10 shot grouping the first time around, the second go resulted in a 3 inch 10 shot group which is pretty good for an airsoft pistol using light weight .20 gram BB's at this range.
All in all the G&G Xtreme 45 CO2 Blowback Airsoft Pistol performed very well for me and considering the fairly low price point and long list of features I would have to say it is good value for the low cost, and it has some pretty nice curb appeal going for it too.
Trigger Pull: The trigger pull on the Bolt Airsoft B4A1 is fairly short and light as it is essentially just an on off switch for the internal electronic components. You can shoot this gun very quickly in semi auto mode, and of course in full auto when full auto position is selected. As is with all AEG rifles there is a bit of a delay while the spring is retracted and released, this is not as noticeable in full auto.
Accuracy: I tested the B4A1 Airsoft rifle by putting around 10 rounds into a target from 30 feet with .36 gram Airsoft 6mm BB's while using a semi rested position (sand bag in the front - standing in the rear). I used a non-magnified red dot scope for this test rather than using the built in iron sights. I got very good result in semi auto and even with the recoil making my sights jump around a bit in full auto still stayed well centered on target and got about a 1.5 inch group in both semi and full auto. My chronograph testing with lighter .20 gram BB's resulted in a 421 fps 5 shot average.
Build Quality: The Bolt Airsoft B4A1 Metal AEG Carbine is very well made with a full Metal upper and lower receiver, along with metal and polymer parts exactly where they would be on the real steel version of an actual Colt M4. The only plastic or nylon components are the stocks and the grips and perhaps some internal parts. I found the adjustable stock and magazine tolerance to be tighter than my King Arms M4A1 I previously reviewed which showed the Bolt B4A1 had a bit higher quality in the workmanship, for the most part the fit and finish was very good!
Realism: As with many Airsoft guns, there is great attention to realism and the Bolt Airsoft BRSS B4A1 Carbine is another great example of an Airsoft Carbine based on the Colt M4 platform. It is an AEG but because of the BRSS (Bolt Recoil Shock System) you get a very nice compromise between a conventional AEG and a GBB (Gas Blow Back Airsoft) gun. In other words, like a standard AEG I get that endless stream of consistent BB's flying down range on target but unlike a true Gas Blow Back Airsoft gun, I don't get that drop off in power and limitation to about 30 usable rounds per magazine . What I do get similar to a GBB is that recoil action that helps make the shooting experience so much more believable! Even the sound from the Bolt B4A1 is much snapper than a standard AEG and more like a GBB. I also like the fact that the charging handle and forward assist work similarly to a real M4 and also the dust cover cleverly exposes the bolt and internal hop-up for easy adjustment along with the bolt cycling just like a GBB rifle would cycle which is similar to a real steel M4.
Great attention to detail with lots of working parts.
All Metal upper and lower receiver, lots of metal parts throughout.
Semi auto & full auto selectable.
High capacity 300+ round magazine.
Removable carry handle with Weaver/Picatinny rail underneath.
Nice high 420 real FPS.
Extremely accurate for plastic BB's.
Fully adjustable sights with two position Peep sights.
6 position adjustable stock.
Easy access to internal hop-up system.
Realistic Blowback Recoil system (BRSS) for a very believable shooting experience!
Cons:
May not get off as many shots per battery charge as a traditional AEG because of the Bolt Recoil Shock System.
Does not come with battery or charger but most higher end AEG's also do not.
Not yet readily available in Canada, maybe we can change that :)
Comments:
The Bolt Airsoft B4A1 Blowback Airsoft Carbine is a great compromise for the avid Airsofter looking for a practical skirmish weapon, but also craving the realistic experience of having blowback with recoil which up until now was really only provided by Gas Blow Back systems. I really like this concept and find it great fun to shoot even if its just for plinking in the yard. The overall quality is very good and you just have to love the M4 platform it's based on. If you're into customizing you can mix and match many external and internal parts with other existing Airsoft mechanical parts and I would imagine real steel accessories. I like mine as is with my addition of a riser and Red Dot and if I every get a chance to get out for a skirmish this will be my weapon of choice for sure!
