View fullsize

Type: Air Pistol.
Manufacturer: Sig Sauer ASP
Model: Sig Sauer ASP P320.
Materials: Metal and plastic build.
Weight: 1.81 pounds (821 Grams).
Barrel: 4.75 inches - Rifled steel.
Propulsion: 12 gram CO2.
Action: Blowback single and double action.
Ammunition Type: .177 caliber pellets and 4.5mm Steel BB's.
Ammunition Capacity: 30 round belt fed stick magazine.
Max FPS: 430.

View fullsize

Trigger Pull: The trigger pull on the Sig Sauer ASP P320 CO2 Blowback .177 Caliber Pellet Pistol is a lot better than I thought it was going to be considering each time you pull the trigger it has to advance the 30 round belt fed magazine and cock the internal hammer since it is double action only. The blowback operation is really only for show and feel since it does not cock the hammer for a more single action type trigger pull. You can expect a fairly long trigger pull because it is double action only but overall it is not too heavy.

View fullsize

Accuracy: I have not done my official Field Test Shooting Video for the Sig Sauer ASP P320 CO2 Blowback .177 Caliber Pellet Pistol but hope to have it done shortly. Since I also haven't really done an official shooting test for the Sig Sauer P350 and P226, I figure I will test out all three of them at the same time.

View fullsize

Build Quality: The Sig Sauer ASP P320 CO2 Blowback .177 Caliber Pellet Pistol is a bit heavier (closer to 2 pounds) than the P250 which hits the scale at only 1.5 pounds , this does make the Sig Sauer P320 feel a bit more solid in the hand. The Sig Sauer P320 has a metal slide and polymer frames similar to the real steel version which gives it authentic weight, balance and handling. Sig claims that their entire APS line of pellet guns is life tested for 15,000 shots so you know this gun is going to last and provide years of shooting fun. The fit and finish seem really good, so far no real paint or finish problems and all mechanically everything is operating as it should.

View fullsize

Realism: The Sig Sauer ASP P320 CO2 Blowback .177 Caliber Pellet Pistol is a very close replica of the real steel Sig Sauer P320. The hammer, slide catch release and take down leaver are purely for show with the hammer being moulded into the slide and frame. One slight disappointment for me is when a gun does not have a cut out ejection port, that is also the case with the otters ASP Sig Sauer airguns like the P226 and P250 but it does not take away from the shooting fun in any way.

Buy Sig Airguns in the: Replica Airguns Store

View fullsize

Pros:

• Good overall replica of the real steel Sig Sauer P320.

• Designed by Sig Sauer and made in Japan, fully Sig Sauer licensed.

• Should have nice heavy blowback operation like the ASP P250 and P226.

• Has better weight than the P250, almost half a pound heavier.

• White dot sights for easy target acquisition and accessory rail for add ons.

• Super high capacity 30 round belt feed magazine.

• Decent feel to the trigger not heavy or as sticky as I thought it might be having a 30 round belt fed magazine.

View fullsize

Cons:

• Hammer is moulded into the slide and frame, does not function at all.

• Sight are non adjustable.

• Ejection port is not cut out and there is no working slide catch.

View fullsize

Comments:
I was happy when Sig Sauer released their ASP Sig P250 and P226 CO2 Blowback Pellet Pistols with their 16 round double sided stick magazines like we have seen in several otters CO2 Pellet Pistols. But I love the introduction of the 30 round belt fed magazine. I am hoping the belt fed magazine performs while actually shooting pellets as good as it feels when dry firing it, I guess we will have to wait and see when I do my Field Test Shooting Video :) Overall the new Sig Sauer ASP P320 Pellet Pistol looks to be an upgrade of sure to the P250 in terms of improved weight and a higher capacity magazine.

My Vimeo Table Top  Review of the Sig Sauer ASP P320 CO2 Blowback .177 Caliber Pellet Pistol:

Buy Sig Sauer Airguns in our Canada Store

 Buy Sig Sauer Airguns in our US Store
 

View fullsize

Another 4.5mm Steel BB Field Test Shooting Review from the new Sea Can Airgun Shipping Container Shooting Range. Yes it's a Crosman but it's really made by KWC and is based on the KWC Beretta / Taurus M92. Depending on which version you get, it came in either semi auto only or semi auto and full auto selectable. The Crosman version does shoot right out of the box in both semi and full auto which is nice.

On to my performance results with the Crosman PFAM98 Taurus PT-92 CO2 Blowback BB Pistol. My feet per second velocity results using a brand new CO2 in a 22-23 celcius environment where right up around 333 fps from a 5 shot string. This is about what we are use to from KWC full blowback CO2 BB Pistols.

View fullsize

Moving on to accuracy, I shot 10 rounds at my paper target which is setup about 30 feet away. I was also using a rested seated shooting position with my hands and gun resting on a sandbag upfront. I did have to reset this test as one of my cameras did not cooperate the first time around and this may have effected the accuracy juts a bit as velocity spread can make the BB's spread out a bit especially high and low on target. I did get a nice 5 shot group that was in a tight under one inch group but some of the other 4.5mm Steel BB's did shot higher and lower leaving the tighter grouping.

When I put the Crosman PFAM98 Taurus PT-92 CO2 Blowback BB Pistol in full auto mode and released the last 10 or so BB's they of course sprayed the target randomly. This was expected with the heavy blowback and fast shooting.

View fullsize

Another Airgun Shipping Container (Sea Can) Shooting video and for this indoor filed test I put the KWC - Cybergun M45A1 1911 CO2 Blowback Airsoft Pistol through its paces.

What I am super happy about is that my Chrony Chronograph seems to be working really well as I tested a pellet, steel BB and Airsoft pistol out today and every single round through my Chrony got a reading :)

Now back to the Field Test Shooting Review at hand... I started off by placing 5 shots through my Chrony Chronograph using a brand new CO2 with .20 gram Airsoft BB's and got a really consistent reading for all 5 shots with an average of 357. The lowest shot was 353 and the fastest shot was 364 so all shots where really close in velocity. The container temperature was a near perfect shooting temperature of 23 degrees Celsius which was ideal for optimal CO2 velocity testing.

View fullsize

During my accuracy portion of this Field Shooting Test. I used my new seated in the back and sand bag rested up front shooting position which is about 30 feet back from my paper target. I did notice during my Chrony testing that the Cybergun KWC Colt 1911 Rail Gun M45 A1 CO2 Blowback BB Pistol liked to shoot a bit high, perhaps the hop-up needs a bit of twerking? So for my accuracy testing I shot at the bottom ring of the target, this helped me get more shots on the paper for sure but the Airsoft BB's still moved around a bit vertically. I was able to get about a 4-5 inch 10 shot grouping which is totally acceptable for a close range Airsoft sidearm and in an Airsoft battle I would think even shooting at about 50 feet or so I could easily hit a persons mid section consistently.

The Cybergun KWC Colt 1911 Rail Gun M45 A1 CO2 Blowback BB Pistol has a ton of blowback kick to it and a super nice single action trigger like all the KWC 1911's The modern Tactical coloration and trimmings makes this pistol a great choice as a present day side arm. It's real looker for sure with performance to match!

Buy Colt 1911 Rail Gun Airsoft Pistol in Canada

Buy Colt 1911 Rail Gun Airsoft Pistol in the US

View fullsize

For my first official Field Test Shooting Video I test out the Crosman American Classic P1322 22 Caliber Pellet Pistol! Perhaps I should start calling these videos Sea Can or Shipping Container Shooting videos? Anyway, like always I put some rounds through the Chronograph to see what kind of real world fps I get from the Crosman American Classic P1322 22 Caliber Pellet Pistol. You will all be happy to know the Chrony is working really well in its new home. I played around with it a bit and found that using the light kit I bought gets me very consistent fps readings :)

Since the Crosman American Classic P1322 22 Caliber Pellet Pistol is a multi-pump airgun there is no real need to shoot more than 3 or so shots, after all there is a fair amount of pumping involved. After three consistent test shots the variation was only about 2 fps apart coming in at an average of 491 fps using Crosman flathead pellets that I would say are around 12-13 grain in weight. Just for fun a did a half pump only cracking the Crosman American Classic P1322 22 Caliber Pellet Pistol 5 times to see what a half power shot would result in and it did scrub off about 200 fps, still good enough for target plinking.

View fullsize

Next up I performed my accuracy test shooting from close to 30 feet back on a paper target using a rested position, (sitting in the back with my hands resting on a sand bag). Still a bit of human factor involved but stable enough to get a good idea of the accuracy for the Crosman American Classic P1322 22 Caliber Pellet Pistol. I had a bit of a camera technical problem so I ended up performing this test twice, the first time I got about a 3/4 inch 5 shot group. The second time I rushed it a bit and ended up widening out the group a little.

Overall the Crosman American Classic P1322 22 Caliber Pellet Pistol is a really great target and even small pest close range pistol that you can pickup at a very affordable price. I really wish we carried a few of the Crosman airguns, at least ones like this, perhaps down the road...

Type: Blowback Airsoft Pistol.
Manufacturer: KWC - Distributed by Cybergun.
Model: Colt 1911 M45A1.
Materials: Almost all metal.
Weight: 2 pounds (907 grams).
Barrel: Metal non-rifled.
Propulsion: CO2 x 1.
Action: Semi auto blowback, single action only.
Ammunition Type: 6mm plastic Airsoft BB's.
Ammunition Capacity: 17 round full size metal magazine.
FPS: 340+ using .20 gram BB's.

Trigger Pull: The trigger pull on the Cybergun KWC Colt 1911 M45A1 CO2 Blowback Airsoft Pistol is what you would expect from a true single action 1911 styled pistol and typical to all the other KWC 1911's on the market. It has a short take up and then a nice light and crisp release. The working grip safety is a nice touch requiring your palm to be pressed against it for the trigger and hammer to operate..

Accuracy: At this point I have not shot the Cybergun KWC Colt 1911 M45A1 CO2 Blowback Airsoft Pistol, I imagine it should perform well considering it has adjustable spin-up or hop-up. According to the manufacturers claimed fps, we should get somewhere in the mid to high 300 fps range using .20 gram Plastic Airsoft BB's. I'll add this one to the list of airguns I need to field test review!

Build Quality: Most KWC built full blowback airguns are built pretty well with an almost all metal build and good overall fit but sometimes the finish can wear off a bit especially in the high points. The Cybergun KWC Colt 1911 M45A1 CO2 Blowback Airsoft Pistol seems to have a bit heavier finish on it. I looks really good and seems to be holding up well.

Realism: The Cybergun KWC Colt 1911 M45A1 CO2 Blowback Airsoft Pistol is a close replica of the real steel Colt 1911 M45A1 in almost every way other than the fact that it shoot s6mm airsoft BB's rather than 45 auto bullets :) The only real notable cosmetic difference I saw was the rail having less notches in it. Other than that it is bang on including the layered grips.
Available From: The Replica Airguns Store.

Pros:

• All metal construction - Good weight and solid feeling gun.

• Nice heavy blowback action.

• Very Accurate 1911 M45A1 styled replica.

• True 1911 Single action trigger, excellent pull, very smooth and light.

• Accurate trigger design and working grip safety.

• Lots of tactical upgrades on this version (Tac style trigger and hammer, textured grips, ambidextrous safety, white dot sights, Rail for accessories)

• Love the desert tan color and layered grips.

Cons:

• Sacrifice fps and shots per CO2 because of the heavy blowback but worth it.

• Finish on the Cybergun and KWC guns can were off on the high points a bit but some people like the look.

• Comes with the orange tip (I took mine off).

Comments:

I have always been a big fan of the KWC line of full blowback airguns and this one is no exception.  It's kind of interesting that KWC does not seem to make there own blinded out versions of these guns and that a company like Cybergun is distributing them? They do look really great and this entire line with all the variations and new models will for sure keep selling these airguns. And they don't just come in Airsoft versions, I will also be taking a look at some similar 4.5mm Steel BB KWC made airguns shortly!

My Vimeo Video Review for the Cybergun KWC Colt 1911 M45A1 CO2 Blowback Airsoft Pistol:

Buy Cybergun M45A1 Airsoft Pistol in Canada

Buy Cybergun M45A1 Airsoft Pistol in US

Type: Pellet air revolver.

Distributed by:UmarexUSA.

Model:Single Action Army Revolver with Colt licensing

Materials: Mostly metal with plastic grips.

Weight: 2.35 pounds (1070  grams).

Barrel: 6.75 inches rifled.

Propulsion: 12 gram CO2.

Action: Revolver, single action only.

Ammunition Type: .177 cal. pellets.

Ammunition Capacity: 6 rounds.

FPS: 380.

Trigger Pull: Trigger pull on all the Umarex Single Action Army BB and Pellet Revolver is really great. Being that these Single Action Army Revolvers are single action only, most of the work is done while you pre-cock the hammer with your thumb. The trigger single action pull is under 2 pounds and has virtually no take up with a crisp release. I love the ratcheting sound of the cylinder as you pull back the hammer just like using a real SAA Revolver!

Accuracy: I have not yet tested the Umarex Colt Single Action Army Nickel & Gold Pellet Revolver so far but expect it to perform very similarly to the 4.5 inch barreled pellet shooting version I tested a while back. On that Field Test Shooting review I was abel to get pretty close to the claimed fps with an average of 378 fps. During my accuracy portion shooting from 30 feet back onto a paper target I got a very respectable .75 inch 6 shot grouping using a semi rested position. I do expect the slightly longer barrel on the Nickel and Gold version to perhaps improve fps slightly.

Build Quality: All of the Colt Single Action Army BB and Pellet Revolvers have a mostly all metal construction other than the plastic grips and any seals. The fit and finish is excellent with a great overall weight in the hand. The mechanical action of the hammer and trigger feels just like it would on a real single action army revolver. I really like the two tone nickel and Gold finish on this longer barreled SAA revolver.

Realism: In terms of replicating a real steel Colt Single Action Army Revolver, again these Umarex old west 6 shooters are absolutely amazing replicas. It's really hard to tell the airgun version apart from the real steel version, with the exception of the smaller diameter shells and the discreet safety switch located under the frame. Even the barrel is nicely recessed and has some fake rifling twists in it to give the appearance of a large caliber barrel opening. The CO2 is well hidden with the Allen key built into the handle so no ugly CO2 screw tab hanging down.

Available in the:Replica Airguns Store

Pros:

• Still the best airgun reproduction of the Single Action Army Revolver, a very accurate replica of the real steel old west version.

• Nice large caliber Recessed barrel.

• Great weight and feel in the hand.

• Shell loading design that loads from the back so no need to remove shells if you wish not to.

• Hammer and trigger action is about perfect, no take-up, very crisp and super light (under 2 pounds).

• Nickel and Gold finish looks really great!

• Colt licensing via Umarex.

• Very well concealed CO2 with built in Allen key.

• Discreet safety location under the frame.

• Longer barrel is unique and should get a bit higher fps than the standard  shorter barreled versions.

Cons:

• A lot more expensive than the standard barrel length in standard finishes.

• Real version would shoot 45 caliber, dummy shells are actual closer to 357 so a bit smallish.

• The safety in all of these ghost is really firm and hard to change.

Comments:

We have pretty much established that these Umarex Colt Single Action Army pistols are fantastic airgun copies of the old west real steel 6 shooters in pretty much every way. For this reason they have been super popular! The Umarex Colt Single Action Army Nickel & Gold Pellet Revolver is yet another rendition of this same airgun but with a longer barrel and the tow tone Gold and Nickel finish. You will pay a bunch more for the longer barrel and two tone finish, is it worth it? If your on a budget perhaps not but if you want something that really stands out and may even perform just a little better than pony up the extra bucks and pick one of these beauties up.

My Vimeo Table Top Review for the Umarex Colt Single Action Army Nickel & Gold Pellet Revolver:

Buy the Umarex Colt SAA Pellet Revolver in Canada

Type: Blowback Airsoft Pistol.

Manufacturer:KJWORKS Distributed by ASG

Model:X9 Classic

Materials: Metal slide & frame.

Weight: 2.1 pounds (950 grams).

Barrel: Metalnon-rifled smooth bore.

Propulsion: 12 gram CO2.

Action: Blowback, single and double action.

Ammunition Type: 4.5mm steel BB's.

Ammunition Capacity: 16 rounds.

FPS: 312+ fps.

Trigger Pull: The trigger pull on the ASG/KJWorks Beretta X9 Classic is very good in both single and double action. Double action is a bit longer and heavier than when shooting in single action since the hammer is being drawn back, but not overly heavy by any means. Single action shooting is short, light and crisp as you would expect when shooting a real steel Beretta 92 style pistol.

Accuracy: I have not done my actual Field Test Shooting video review for the ASG/KJWorks Beretta X9 Classic CO2 BB Pistol but I did get the chance to make a short preview video where I shot the Airsoft version of this M9 Beretta at some clay pigeons setup around 20 feet away. I was able to pop the center out of the clay pigeons no problem and found that even without any practice I was consistently hitting dead center on most shots. I am not sure exactly what the FPS will be btu it shoudl for sure get at least the claimed 312 fps if not a bit more.

Build Quality: As expected, the ASG X9 Classic Beretta M9 CO2 Blowback 4.5mm BB Pistol build quality is just like all the other KJWorks Airsoft guns I've tested so far. The ASG 4.5mm Steel BB shooting X9 Classic has more of a Matt finish but I kind of like it, not so many finger prints on the gun. All  the tolerances between the moving parts like the slide and frame are very tight showing excellent workmanship and machining from KJWorks.

Realism: The ASG X9 Classic Beretta M9 CO2 Blowback 4.5mm BB Pistol is an excellent copy of the real steel popular Beretta M9, it is really hard to tell it apart from the real version and the ASG X9 Classic can even be field stripped in the same manor as a real Beretta M9 Semi Auto pistol with the similar functioning parts. The only missing aspect would be Beretta Licensing since the ASG version is unlicensed.

Available in the:Replica Airguns Store

Pros:

• No ugly white warning instructions on the slide.

• Really nice replica of the original Beretta M9.

• Great weight and feel to it.

• All metal design, fit and finish is very good as is with all KJWorks made guns.

• Strong slide spring so should have nice heavy blowback action.

• Realistic working safety and working slide catch and release.

• Full size dropout metal magazine that holds steel BB's and CO2.

• Can be field stripped like original Beretta M9.

• KJWorks quality.

Cons:

• Not licensed like the Umarex version.

• None adjustable sights and white dot sights are kind of light.

• Will eat up CO2 pretty quickly. 

Comments:

There are very few 4.5mm Steel BB guns made by KJWorks and it seems that ASG as far as I know is the only distributer that has teamed up with KJWork to have them make some of their guns, I reviewed the ASG CZ 75 which is another ASG/KJWorks distributer 4.5mm CO2 Blowback Pistol. I don't even think you can get the 4.5mm Steel BB shooting version direct from KJWork? What I love most of all about the ASG X9 Classic Beretta M9 CO2 Blowback 4.5mm BB Pistol is that it is made by KJWorks since there are already a lot of Beretta M9's and Mod. 92's already out there but if I could only have one it would probably be the ASG X9 Classsic!

My Vimeo Table Top  Review of the ASG X9 Classic Beretta M9 CO2 Blowback 4.5mm BB Pistol:

Buy the ASG X9 Classic BB Pistol in Canada

Buy the ASG X9 Classic BB Pistol in the US

I have some new guns for everyone to checkout which is always good for everyone, especially me :)

In this update video I show you around three pistols one Arisoft Rifle. With the pistols we have a mixed bag of Pellet, steel BB and plastic Airsoft. First off I take a look at the ASG X9 Classis Beretta M9 CO2 Blowback 4.5mm Steel BB pistol, which by the way is actually made by KJWorks so we know this it's going to be a quality gun! I then switch things up and showoff the new long barrel CO2 powered Umarex Colt Peacemaker SAA pellet revolver that sports a Nickel and Gold finish. Last for the pistols we take a look at the 6mm Airsoft firing Colt 1911 Rail Gun in the Dark Earth finish, it's basically a KWC 1911 but with a little extra bling.

Last but now least to show you in this update video is the ASG CZ Scorpion EVO 3 A1. This product was developed by ASG in cooperation with CZ and is made to give the Airsoft Player the closest shooting experience they can possibly get to handling and shooting a real CZ Scorpion EVO 3 A1!

ASG X9 Classic Beretta Blowback CO2 BB Pistol:

• Full metal

• 4.5mm steel BB's

• Full blowback action

• 2.1 pounds

• 16 Round full size drop out metal magazine

• 312 fps

• Single & double action

Umarex SAA Colt Peacemaker Nickel & Gold Co2 Pellet Revolver:

• Full metal

• .177 caliber pellets

• Gold highlighted cylinder, hammer & trigger

• 6.75 inch barrel

• Shell loading 6 shooter

• 380 fps

• Single action only

Colt 1911 Rail Gun Dark Earth Blowback CO2 Airsoft Pistol:

• Full metal

• 6mm Airsoft BB's

• Comes with red tip but can be removed with some work

• Full blowback action

• 2.1 pounds

• 17 Round full size drop out metal magazine

• 345 fps

• Single action only

ASG CZ Scorpion EVO 3 A1 AEG Airsoft Rifle:

• Metal & plastic build

• 6mm Airsoft BB's

• Comes with red tip but can be removed easily

• AEG: single shot, 3 round and full auto shooting modes

• 5.3 pounds

• 75 Round magazine

• 394 fps

• Full CZ licensed

Buy Umarex SAA Colt Peacemaker Nickel & Gold Co2 Pellet Revolver in Canada

Buy ASG X9 Classic Beretta Blowback CO2 BB Pistol in Canada

Buy ASG X9 Classic Beretta Blowback CO2 BB Pistol in the US

Buy Colt 1911 Rail Gun Dark Earth Blowback CO2 Airsoft Pistol in Canada

Buy Colt 1911 Rail Gun Dark Earth Blowback CO2 Airsoft Pistol in the US

Buy ASG CZ Scorpion EVO 3 A1 AEG Airsoft Rifle in Canada

Buy ASG CZ Scorpion EVO 3 A1 AEG Airsoft Rifle in the US

Type: Pellet Air Pistol.

Manufacturer: Crosman.

Model: P1322 American Classic.

Materials: Metal & plastic.

Weight: 2 pounds.

Barrel: 10.25 inches, metal rifled.

Propulsion: Multi-pump pneumatic, up to 10 pumps.

Action: Bolt-action single shot, single action only.

Ammunition Type: .22 caliber pellets.

Ammunition Capacity: 1 round.

FPS: 460.

Trigger Pull: The trigger pull on the Crosman American Classic P1322 22 Caliber Pellet Pistol is non-adjustable but is short and fairly light with virtually no creep at all, it's just right there! The Crosman American Classic P1322 will allow for very accurate shot placement with only a little trigger time required to get use to the release tension required.

Accuracy: I found my Original Crosman 1377 (The .177 caliber version of this airgun) to be an amazing target pistol, getting about a 1/2 inch grouping from 30 feet out in a semi-rested position. And I even performed my accuracy test twice with the same result each time. In terms of fps performance, the Crosman American Classic P1322 22 Caliber Pellet Pistol is not required to be detuned for Canada importation so we should see very close to 460 fps even using heavier grain lead pellets! Make sure to look for my upcoming Field Test Shooting video for the Crosman American Classic P1322 22 Caliber Pellet Pistol.

Build Quality: The Crosman American Classic P1322 22 Caliber Pellet Pistol is not a fancy looking airgun but it gets the job done with a mostly all metal design and build. Remember this Croman configuration has been around since 1977 so about  40 years and has pretty much stayed the same so Crosman must be doing something right with the American Classic series if it has stood the test of time with very few changes to its design other than some cosmetics ones.

Realism: The Crosman P1322 American Classic Air Pistol is not a replica of any gun out there. The P1322 is made as a target airgun, so it looks like a target air pistol and is not expected to resemble a tradition real steel pistol of any sort.

Pros:

• Fairly inexpensive target pistol (under $100 Canadian - $79 US)

• Know to be very accurate.

• Ability to regulate power with the amount of pumps.

• Mostly all metal construction.

• Rifled steel barrel.

• Adjustable rear sight.

• Light single action trigger.

• Would be good for small close shot pest control because of good FPS and good accuracy for shot placement ability.

• Lots of mods and upgrades available for this series of Crosman Airguns.

Cons:

• The trigger is a bit thin (Can be upgraded).

• Rear sight is adjustable but is hard to setup.

• All black sights are hard to aim on darker targets.

• Pumping is fairly firm and will take some time for max 10 pump power.

Comments:

The Crosman American Classic P1322 22 Caliber Pellet Pistol is a bit of a sleeper target pistol. It has been around for a long time and for this reason can be overlooked. It also is a super flashy looking airgun that requires a bit of manual pumping to get to maximum power. There is also the kind of finicky sight setup required to get this air pistol to shoot on target. If you can put all that aside you have yourself a super accurate and rather powerful little target or even small pest control airgun for a lot less money than some other pellet target pistols out there. And to be honest I would trade having to pump this gun up over a springer for the main reason that the recoil is so much less violent on a pump gun allowing for better accuracy at the end of the day. When you factor in all the mods that are available for this line of Crosman Airguns the sky is the limit allowing for a ton of customization in performance and looks.

My Vimeo Video Review of the Crosman P1322 American Classic .22 Caliber Target Pistol:

Buy Pellet Airguns in the Canada Store

First off, I want to thank Crosman for providing these two guns for review! Now they're not exactly new guns by any means but for sure worth showing and doing some update reviews for.

Starting with the Crosman PFAM98 Taurus PT-92:

The Crosman PFAM98 Taurus PT-92 is essential a KWC made M92 also branded as the same gun as the Cybergun GSG 92 and the Swiss Arms P92.

So for all intense and purposes if you have watched any of my other revise on this line of KWC Beretta /Taurus BB pistols and even Airsoft versions then this BB gun should be really familiar to you.

History of the Taurus PT-92:

It is often referred to as a Berate 92 copy but in fact it is a Taurus PT-92 replica. The Taurus PT-92 is a product of Brazil, Taurus actually bought the entire Brazilian Beretta factory back in 1980 including drawings, tooling, machinery, and a very experienced work force to make the guns. Taurusimmediately sought to improve on the Beretta design, resulting in the popular and acclaimed Taurus PT-92.

Specifications for the Crosman PFAM98 Taurus PT-92:

• Full Blowback operation.

• Full metal frame, slide and magazine.

• 12 gram CO2.

• 4.5mm steel BB’s.

• 20 shot full size drop out metal magazine.

• Smooth bore barrel.

• Single and double action trigger.

• 2.44 pounds (1107 grams).

• Up to 400fps.

• Replica of Taurus PT-92.

• Made for Crosman by KWC in Taiwan.

Next up the Crosman American Classic P1322.

The American Classic P1322 is basically a .22 caliber version of the .177 caliber 1377 Pneumatic Pump Air Pistol. So make sure to watch the video reviews I have already done for the Crosman American Classic P1377. Other than caliber the .22 caliber version at least in Canada is more powerful since it has not been detuned for Canada import. The .22 caliber version has a claimed fps of 460 which is under our 500 fps import limitation while the standard non detuned .177 caliber version has a max claimed fps of up to 600 which can set off alarms at customs. For this reason the Crosman American Classic P1377 Canada version is detuned to shoot under 500 fps.

Crosman use to make a similar version of the Crosman American Classic P1322 called the Back Packer which had a slightly longer barrel and came with a removable stock. You can kind of replicate this gun by adding the stock but it will have a shorter barrel. Keep in mind there are a ton of mods available for this series of Crosman airguns including barrels, bolts, trigger, Internals stocks, scope mounts…

PHOTOSpecifications for the Crosman American Classic P1322:

• Metal and plastic construction.

• Pneumatic pump.

• .22 caliber lead pellets.

• Single shot bolt action.

• Rifled metal barrel.

• Single action only.

• Up to 460fps using lead pellets (10 pumps).

• 1.88 pounds (853 grams)

Keep posted for my full update reviews for these airguns...

I've already done Table Top Video Review for both the ASG CZ Scorpion VZ61 and the ASG B&T BT5 AEG 6mm Airsoft Guns so make sure to checkout both those videos.

What I hav not done so far is make a Filed Test Shooting video for either gun since this winter has been rather brutal here in BC Canada. Today I did manage to get outside and put some rounds through both the ASG CZ Scorpion VZ61 and the ASG B&T BT5 AEG 6mm Airsoft Guns so at least I can report back to everyone on how they performed for me. Sorry still no actual shooting video as my outside time was kind of limited due to it still being cold, we are even expecting some more snow tonight and over the next few days and it's March!

Getting back to my preliminary shooting testing, the ASG CZ Scorpion VZ61 only shot a slight bit higher then 250 but it was the more accurate of the two AEG Airsoft Guns getting close to a 1 inch 10 shot grouping using my standard 30 foot back semi rested shooting position. It did shoot a bit low but perhaps  a hop-up adjustment should fix that problem.

Next up I tested out the ASG B&T BT5 MP5 PDW Replica and it did have a little more power hitting closer to 300 fps but it was not as accurate as the CZ shooting a bit high and to the left with most shots within about 1.5 inches, still pretty decent from 30 feet back.

Overall both AEG Airsoft Guns where fun to shoot and when I did let them lose to shoot in full auto mode they performed as expected laying down a stream of Airsoft BB's till the mags where empty :)

Distributer: RWA (Made in Hong Kong)

Model: Interdynamic KG-9

Materials: Steel, aluminum and plastic (polymer) construction.

Weight: 3.22 pounds (1460 grams).

Length: 15.7 inches (398mm).

Propulsion: AEG.

Action: Full auto only.

Ammunition Type: 6mm Airsoft BB's

Ammunition Capacity: 90 round magazines (Comes with 2).

FPS: 360+.

Trigger Pull: The trigger pull on the RWA KG-9 AEG Airsoft Machine Pistol is what you would expect form an AEG pistol as it is basically an on/off switch. Since the RWA KG-9 AEG Airsoft Machine Pistol is full auto only it is not easy to shoot a single shot, it can be done with a very short trigger pull but even then you get the occasional multiple shot. The RWA KG-9 AEG Airsoft Machine Pistol like the real steel original version is full auto only and that's what makes it so fun!

Accuracy: I did get a chance to take the RWA KG-9 AEG Airsoft Machine Pistol outside and put some rounds through my Chronograph and down range at a paper target. I averaged just under 340 fps using .20 gram 6mm Airsoft BB's which is about perfect for this compact machine pistol. I also placed about 10 rounds down range 30 feet back using my standard semi rested shooting position while trying to shoot in semi auto and got a pretty decent 1.5 to 2 inch grouping that was a little high but well centered left to right. Elevation could be adjusted using the hop-up.

Build Quality: The RWA KG-9 AEG Airsoft Machine Pistol is really one of the best made Airsoft guns I have seen in a while, all the metal parst are going to be real steel or aluminum, not your standard zinc alloy found in most airguns these days. The full upper is stamped steel along with the 90 round magazines, the lower is plastic with a few aluminum parts here and there. The fit and finish is also excellent!

Realism: The RWA KG-9 AEG Airsoft Machine Pistol is a replica of the Swedish made Interdynamic KG9 Open Bolt SMP, not the ntratec Tec-9 which was the American version of the KG9. For the most part the RWA Airsoft version is exact with the exception of the barrel shroud being slightly longer to accommodate the 7.4v LiPo batteries.

Pros:

• Lots of steel in this gun including full upper, barrel, pins and magazines.

• Very high quality build with a solid weight and excellent fit and finish.

• Fairly high rate full auto fire.

• Comes with battery and two magazines.

• Has almost perfect usable working rate of fire averaging around 340 fps with decent overall accuracy.

• Working cocking handle.

• Fully Licensed.

Cons:

• No blowback but there is some recoil feel from the heavy spring action.

• No semi auto mode, full auto only.

• Sights are not adjustable, can only use hop-up to adjust elevation.

• Limited on battery choices.

Comments:

The RWA KG-9 AEG Airsoft Machine Pistol is a really cool looking Airsoft gun, it is a bit larger than most hand guns but could still be used like one since it does not have a stock and can be used for similar shooting situations. The advantage is you have 90 rounds of full auto ammo at your disposal in a size format that is super compact and easy to manoeuvre. You also get some pretty decent power for longer range shooting and the accuracy out of the box at a variety of ranges is also really good. You could even use the RWA KG-9 AEG Airsoft Machine Pistol easily as a primary or even kick ass backup gun as it is super versatile.

Watch my Vimeo Table Top Review of the RWA KG-9 AEG Airsoft Machine Pistol:

Type: Airsoft Pistol.

Manufacturer:Umarex.

Model:H&K USP.

Materials: Mostly clear plastic exterior with metal magazine and internal metal parts.

Weight: 1.2 pounds (544 grams).

Barrel: 4 inches, metal non-rifled with internal Hop-up.

Propulsion: CO2 x 1.

Action: Semi auto, double action only.

Ammunition Type: 6mm Plastic BB's.

Ammunition Capacity: 16 round full size drop out magazine.

FPS: 360 (.12 gram BB's).

Trigger Pull: The trigger pull on the Umarex HK USP Clear CO2 Airsoft Gun is pretty light for a Double Action Only trigger and it will allow for some pretty quick rapid fire action shooting. The hammer is basically for show as the hammer is actually situated internally.

Accuracy: So far I have not had a chance to test the Umarex HK USP Clear CO2 Airsoft Gun out but I expect it to get around 300 fps using .20 gram plastic Airsoft BB's and with the internal hop-up it should also be fairly accurate. We will have to find out later on when I get outside and perform my Field Test Shooting Video Review.

Build Quality: My first impressions of a clear plastic gun are that it is going to be cheaply made but this is not the case with the Umarex HK USP Clear CO2 Airsoft Gun. For the most part it is exactly like the all black Steel BB version I already reviewed other than the clear plastic shell. Everything else about the Umarex HK USP Clear CO2 Airsoft Gun is the same and there is a lot internal metal parts including a metal barrel and breach and a full internal metal chassis. I would have like to have seen a metal trigger, hammer, safety and slide catch release.

Realism: The Umarex HK USP Clear CO2 Airsoft Gun is a fully licensed replica of the real H&K USP automatic pistol. Other than it being clear and having a red tip is an extremely close looking and accurate replica of the real steel version. It does not operate the same since it is non blowback and does not have a moving slide but visually it is a very good copy.

Purchased this gun from: The Replica Airguns Store.

Pros:

• Relatively low cost gun, even less than the Steel BB version that is the same other than the clear plastic portions.

• Nice full size drop out magazine that holds the CO2 and Airsoft BB’s.

• Lots of internal metal parts gives decent weight to the gun even though much of the shell is plastic.

• Rail for accessories.

• CO2 screw is well hidden in magazine.

• H&K licensing via Umarex.

• Red dot sights are easy to see on most targets.

• Should have justthe right amount of power for indoor CQB style Airsoft games.

• Makes a good starter pistol for someone getting into the hobby that may not want a gun that looks too realistic. 

Cons:

• Being a clear gun obviously takes away from the realism but that is the point of this gun so as not be confused with a real gun..

• Would have been nice if the magazine was metal like earlier versions of the HK USP.

• Also would have been nice to see more metal parts like the hammer, magazine release, safety, and slide catch release.

Comments:

As I mentioned in my video of the Umarex P99 Clear Plastic Spring Airsoft Pistol, I can be a bit of an Airgun snob and I tend to stay away from the clear Airsoft guns since I like mostly metal guns with blowback operation. That said there is a place for these clear Airsoft pistols. The Umarex HK USP Clear CO2 Airsoft Gun other than being clear looks like a gun and shoots like a gun but will not be confused as being a real gun which can offer some more safety and less stress to all parties involved.

My Vimeo Video Review for the Umarex HK USP Clear CO2 Airsoft Gun:

Buy the Umarex HK USP Clear CO2 Airsoft Gun in Canada

Buy the Umarex HK USP Clear CO2 Airsoft Gun in the US

Type: Airsoft Pistol.

Manufacturer:Umarex.

Model:Walther P99 Compact

Materials: Mostly plastic with some metal parts.

Weight: .5 pounds (227 Grams).

Barrel: 3 inches, metal non-rifled with internal Hop-up.

Propulsion: Spring Piston.

Action: Single Shot, Single Action Only.

Ammunition Type: 6mm plastic Airsoft BB's.

Ammunition Capacity: 11 shot full size drop out magazine with 60 round reservoir.

FPS: 280 using .12 gram BB's.

Trigger Pull: The single action only trigger pull on the Umarex P99 Compact Clear Spring Airsoft Gun is a bit heavier than I expected since generally speaking single action triggers simply just need to release the hammer or striker. There is a little bit of take-up initially but then the release is fairly crisp, just a tad firm but since this is not an action shooter and a full rack of the slide is required to pre charge the internal spring, having a heavier trigger pull is not a big deal and did not seem to effect my accuracy in any way.

Accuracy: I didn't get a lot of shooting time with the Umarex P99 Compact Clear Spring Airsoft Gun but I can say it seemed to be shoot fairly accurately. I tested it out shooting on a paper target from 20 feet back using a non rested standing position. The Umarex P99 Compact Clear Spring Airsoft Gun did shoot a bit high and to the left but my 10 shot grouping was within 1.75 inches with the exception of one stray that shot a little more to the right. I was using .20 gram BB's but they did seem to get to the target pretty quickly and penetrate the paper fairly well. I would say they were traveling well over 200 fps.

Build Quality: The Umarex P99 Compact Clear Spring Airsoft Gun is about a $25 gun so you can't really expect too much in terms of quality materials but that said, the gun does feel solid and well put together. I had no issues shooing it and for the price you should get plenty of good use out of it.

Realism: The Umarex P99 Compact Clear Spring Airsoft Gun is realistic in terms of its shape, operation and even the Walther P99 licensing and trade marks. But as is expected being a clear plastic gun it falls short in terms of feeling and looking the part of a real gun. But that's kind of the point here, this gun is supposed to clearly look like and Airsoft gun and not a real gun including the orange red tip.

Purchase it from: The Replica Airguns Store

Pros:

• Super low cost and even come with an extra mag and some starter BB’s.

• Full size drop out mags are nice.

• All the parts feel pretty tight, does not feel hokey, even has some metal parts where they are needed.

• Has a rail for accessories.

• No CO2 required, just your Airsoft BB’s.

• Walther licensing and Trademarks.

• Slide stays back when out of BB’s.

• Has internal Hop-up.

• Has a floating barrel like the real steel version would.

• Makes a good starter pistol for someone getting into the hobby that may not want a gun that looks too realistic.

Cons:

• Is kind of on the light side at about half a pound.

• The single action trigger is a bit heavy but works fine, you're not going to be shooting rapped fire with this one anyway.

• Being a clear gun obviously takes away from the realism but that is the point of this gun so as not be confused with a real gun.

• Shoots a bit high and to the left.

Comments:

Right from the get go I was not expecting much from the Umarex P99 Compact Clear Spring Airsoft Gunbeing a bit of an Airgun snob and personally tending to stay away from the like of these clear plastic non-blowback super low cost Airsoft pistols. But after playing around with it for a bit I could really see how a first time Airsoft buyer could really enjoy the Umarex P99 Compact Clear Spring Airsoft Gun. It shoots just fine and costs next to nothing to buy and shoot. And I know there are many younger folks that watch my video reviews and perhaps their parents may be sitting on the fence about allowing them to buy an Airsoft gun out of fear that so many of them look so real. The Umarex P99 Compact Clear Spring Airsoft Gun clearly looks like an Airsoft gun which makes it pretty hard to get in trouble with yet you can still enjoy the Airsoft shooting experience without freaking your parents out!

My Vimeo Video Review for the Umarex P99 Compact Clear Spring Airsoft Gun:

Buy the Umarex P99 Compact Clear Spring Airsoft Gun in Canada

Buy the Umarex P99 Compact Clear Spring Airsoft Gun in the US

Content Link Block

Select a page and create a visual link to it. Learn more

Replica Airguns Blog | Airsoft, Pellet, & BB Gun Reviews

This Vimeo Unboxing Preview Video focuses on two AR M4 styled AEG Airsoft Rifles. The G&G CM16 Rifles are all pretty much the same other than the barrel lengths and come in the following versions, the CM16 SRS, CM16 SRL and CM16 SRXL. I also showcase the Umarex HK M27 which is distributed by Umarex but made by VFC which is knwo for their high quality products. I will be following up this Preview Unboxing Video with individual more detailed Review videos for each AEG AR M4 rifle.

G&G CM16 SRS Black AEG Airsoft Rifle

• Type: Airsoft Rifle

• Manufacturer: G&G Armament

• Model: CM16 SRS

• Materials: Metal and Polymer Construction

• Weight: 4.97 Pounds

• Barrel:  8.1 inches

• Propulsion: Electric AEG

• Action:  Semi, Full Auto, 3-Round Burst Modes

• Ammunition Type: 6mm Plastic Airsoft BBs

• Ammunition Capacity: 300 rounds

• FPS: 420 fps

Buy G&G CM16 SRL Black AEG Airsoft Rifle in Canada

G&G CM16 SRL Black AEG Airsoft Rifle

• Type: Airsoft Rifle

• Manufacturer: G&G Armament

• Model: CM16 SRS

• Materials: Metal and Polymer Construction

• Weight: 5.1 Pounds

• Barrel:  10.2 inches

• Propulsion: Electric AEG

• Action:  Semi, Full Auto, 3-Round Burst Modes

• Ammunition Type: 6mm Plastic Airsoft BBs

• Ammunition Capacity: 300 rounds

• FPS: 420+ fps

Buy G&G CM16 SRL Black AEG Airsoft Rifle in Canada

G&G CM16 SRXL Black AEG Airsoft Rifle

• Type: Airsoft Rifle

• Manufacturer: G&G Armament

• Model: CM16 SRS

• Materials: Metal and Polymer Construction

• Weight: 5.24 Pounds

• Barrel:  13 inches

• Propulsion: Electric AEG

• Action:  Semi, Full Auto, 3-Round Burst Modes

• Ammunition Type: 6mm Plastic Airsoft BBs

• Ammunition Capacity: 300 rounds

• FPS: 420+ fps

Buy G&G CM16 SRXL Black AEG Airsoft Rifle in Canada

Umarex H&K M27 Black AEG Airsoft Rifle

• Type: Airsoft Rifle

• Manufacturer: Umarex VFC

• Model: H&K M27

• Materials: Metal and Polymer Construction

• Weight: 6.7 Pounds

• Barrel:  14.2 inches

• Propulsion: Electric AEG

• Action:  Semi, Full Auto

• Ammunition Type: 6mm Plastic Airsoft BBs

• Ammunition Capacity: 320 rounds

• FPS: 400 fps

Buy Umarex H&K M27 Black AEG Airsoft Rifle In Canada

Buy Umarex H&K M27 Black AEG Airsoft Rifle in the US

This Unboxing Preview Video focuses on three Bullpup designed AEG Airsoft Rifles. The two Steyr Aug Bullpups are distributed through ASG while the IWI Tavor 21 is distributed via Umarex. In this Unboxing Preveiw video I take each gun out of the box and go over some basic specification and show you around each AEG Bullpup Rifle a little bit. I will be following up this Preview Unboxing Video with individual more detailed Review videos for each AEG rifle.

Here are some of the basic Specifications for each AEG Airsoft Rifle.

AEG Steyr AUG A3 MP AEG Aisoft Bullpup Rifle

• Type: Airsoft Bullpup Rifle

• Manufacturer: ASG

• Model: Steyr AUG A3 MP

• Materials: Metal and Polymer

• Weight: 3.85 kg (8.5 pounds) 

• Barrel: 21.2 mm (0.83 inches)

• Power Source: Electric AEG

• Action: Semi & Full Automatic

• Ammo Type: 6mm Plastic Airsoft BBs

• Ammo Capacity: 300 rounds

• FPS: 394

Buy AEG Steyr AUG A3 MP AEG Airsoft Bullpup Rifle in Canada

Buy AEG Steyr AUG A3 MP AEG Airsoft Bullpup Rifle in the US

ASG Steyr AUG A2 Tan AEG Rifle

• Type: Airsoft Bullpup Rifle

• Manufacturer: ASG

• Model: Steyr AUG

• Materials: Polymer with Metal Internals

• Weight: 3.39 kg (7.5 pounds)

• Length: 805 mm (31.7 inches)

• Power Source: Electric AEG

• Action: Semi & Full Automatic

• Ammo Type: 6mm Airsoft BBs

• Ammo Capacity: 300 rounds

• FPS: 394

Buy ASG Steyr AUG A2 Tan AEG Airsoft Bullpup Rifle in Canada

Umarex IWI Elite Tavor 21 Airsoft AEG Bullpup Rifle

• Type: Airsoft Bullpup Rifle

• Manufacturer: Umarex

• Model: Steyr AUG

• Materials: Polymer with Metal Internals

• Weight: 3.5 kg (7.71 pounds)

• Length: 755 mm (29.7 inches)

• Power Source: Electric AEG

• Action: Semi & Full Automatic

• Ammo Type: 6mm Airsoft BBs

• Ammo Capacity: 300 rounds

• FPS: 395

It's been a great year for Replica Airguns and I wanted to share with everyone some of my favorites that I reviewed this year. In this Vimeo Video I show some of my top Replica Airgun picks for 2016 and talk a little bit about each one and what I like about it.

Here is a list of the Replica Airguns in this lineup:

• ASG Dan Wesson 715 CO2 Revolver - Comes in 4.5mm Steel BB, 6mm Plastic Airsoft & .177 Pellet.

• Umarex Colt Combat Vet CO2 Blowback 1911 - 4.5mm Steel BB.

• Sig Sauer MPX ASP CO2 Rifle - .177 Pellet.

• Sig Sauer ASP P226 CO2 Blowback Pistol - .177 Pellets.

• Air Venturi ISSC M22 CO2 Blowback Pistol - 4.5mm Steel BB.

• KJWorks KC-02 V2 Ruger 10/22 GBB Rifle - 6mm Plastic Airsoft.

• Umarex S&W M&P40 CO2 Blowback Pistol - 4.5mm Steel BB.

This has got to be one of the most asked questions when people are trying to decide on which CO2 BB Pistol they want to buy. The reality is that most non blowback CO2 BB pistols will generally shoot just over 400 fps and most blowback BB pistols will shoot around 350 fps. Some may shoot a little faster and some may shoot a little slower.

My question is this… What difference will it make if you are shooting a BB at 350 fps versus say 450 fps? I honesty think that some people believe that if they purchase a CO2 BB pistol that shoots a whopping 499 fps, then they have acquired a deadly weapon with crazy stopping power.

The truth of the matter is that even a 500 fps BB gun is still not suitable for even small pest control or hunting, you would only be causing the animal to suffer if you shot it with such a lower powered airgun. So using an air pistol for any kind of personal protection on human sized targets is completely out off the question.

Let’s talk about what CO2 BB pistols are really used for. Shooting at pop cans, shooting paper targets, perhaps setting up some army men and  picking them off one by one. stuff like that. So does it really matter if the BB is going 350 fps versus 450 fps? It’s still going to go clean though a pop can even filled with water, paper is no match for a BB traveling even under 300 fps, and Army men stand no chance when head shot by a steel BB the size of a canon ball to them.

When is power really going to be important in a CO2 BB Pistol? Perhaps if you plan to shoot out at longer ranges but in this case Steel BB’s are not really meant to shoot out at long ranges as most BB pistols do not have rifled barrels meant for long range accuracy. I have found Steel BB guns to be very accurate up to 30 feet or so, even grouping within in a half inch with some CO2 BB pistols, but further out than that and the BB’s start to wander.

Normally higher velocity is what you want when you plan on using your airgun for hunting or pest control but again a CO2 BB pistol simply is not the tool for this job.

One comment I hear a lot from people is that they would prefer more power over blowback action and that they feel that blowback action robs the gun of too much power. Yes blowback does sacrifice some power since it uses a little bit of the CO2 to operate the slide but the benefits of blowback in my opinion are worth the 50 or so fps loss in power. Blowback operation adds realism to the CO2 BB gun simulating recoil, allowing true single action trigger operation and many CO2 BB Pistols will even lock the slide back on the last shot so you know you are out of ammo and can practice your magazine drop and reloading.

One of the most common types of question I get on my Replica Airguns YouTube channel has to be something like… Why is my Airgun not working? Most of the time the amount of info about the problem is limited to something like… “It was working yesterday but now it’s not working anymore” or something like “when I pull the trigger nothing happens”. My personal favorite is… “I took my gun apart and now it doesn’t work!”

I just made a similar video for Blank Guns and as I said in that video, trying to trouble shoot a mechanical or technical problem over the internet is very difficult, this goes for cars, guns, computers or what have you…

In this Why is My CO2 Airgun Not Working video I will however cover some of the more common and obvious problems I have seen relating to why a CO2 Airgun may not be working properly. I really don’t get a lot of questions about Spring Piston or Pump Airguns so I will be focusing on CO2 Airguns in this video. There will be a lot of crossover with CO2 Airsoft guns so this video may be helpful for some of you Airsofters out there

First let’s get the super obvious stuff out of the way! 

• Did you put a new CO2 cartridge in it and is it pierced all the way?

• Did you load BB’s or Pellets into the Airguns magazine and is the magazine in the gun correctly?

• Is the safety off?

• If the gun is a blowback semi auto single action Airgun then did you pull the slide back prior to the first shot?

CO2 Related Problems:

Not all CO2 cartridges are created equal, they often have slightly different shaped nubs on them and some brands will work better than others in different Airguns. If the shape of the CO2 nub does not fit properly into the valve area then it may not pierce or it could pierce but then not allow you to tighten it all the way losing all the CO2 in the process. If the CO2 is coming form the airguns handle to CO2 Valve area then this is an indication that your problem is related to the area where the CO2 enters the airgun.

There is a seal where the CO2 cartridge buts up to the valve, this seal can be damaged or even deformed from usage or even leaving your CO2 in the gun for too long. The outside CO2 Valve seal can also take the shape of a specific CO2 nub so when you use a different brand CO2 the seal may not properly make concat with the new CO2 type you are using, again causing leaking or even the total loss of all your CO2. Watch my YouTube video on “How to Fix Leaking CO2 in an Airgun”.

CO2 Valve Related Problems:

Again, make sure that Outside CO2 Valve Seal is in good condition and any leaking is not being caused by this problem, if you have checked the Out Side Seal and everything is OK with it then perhaps there is a problem with the CO2 valve?

One indication that your CO2 Valve might be the culprit is the total loss of all your CO2 when you try to insert and tighten a new CO2 Cartridge. Usually all the CO2 will exit the barrel, not the handle or valve area. What may be happening is the valve is stuck open or the internal seal is broken or deformed. If this is the case you will have to remove the valve and have a look inside, this is a lot easier on CO2 airguns that have the CO2 valve in the magazine, if the CO2 valve is in the actual Airguns then a lot more disassembly may be required and I would recommend an Airgun technician take care of this for you.

If the gavel is in the magazine then you will have to unscrew it, you may require a special tool for this? Once the valve is out of the magazine  take a look inside and examine the internal seal, also look for any bits of metal shavings as they can disrupt the action of the valve causing leaking. Give the inside of the valve a good clean and then lubricate it with some silence spray. hopefully that fixes your problem!

BB’s getting Stuck in the Blowback Gas Tube:

I have actually made a dedicated video for this problem so I will put a link to it in the description of this video. The main reason people may have this problem is because we all like to rack that slide on our full blowback Airguns, but if you have a fully loaded magazine then each time you reach that slide without shooting the gun, you are inadvertently trying to load another BB into the breach area, the breach is only designed to hold one BB at a time so after a few racks of the slide the newly loaded have no place to go but into the Gas Tube where they can get stuck and cause having to the operation of your Full Blowback CO2 Airgun.

BB’s Rolling Out of the Barrel of Your CO2 Airgun:

This is not actually a fault of the gun but happens because of the way the gun is designed. This situation can happen with certain CO2 Airguns when the gun user pulls the trigger really slowly while the gun is point slightly in a downward position. What is actually happening is the first part of the trigger is made to draw a BB from the magazine into the breach of the gun. If the barrel of the gun does not have a rubber hop-up stopper in it then the BB is free to roll down the barrel and out of the gun. How do you fix this problem? Be more committed to your trigger pull and or shoot at a target that is not so low. Perhaps place your targets slightly higher than the gun so the barrel is not pointing down, especially if you like to take your time with the trigger :)

A Little Maintenance Can Go a Long Way!

Sometimes a good cleans is all you need to do to get things working as they should, again I have already made video Tutorial Showing “How to Clean Airguns and Blank Guns”.

What about stuff like My Airgun is jammed or my trigger is stuck or some random part fell out of my gun?

There is only so much I can cover in this video, most other problems are going to get a bit more complicated to fix and I suggest if your Airgun is not working and the suggestions I have made in this video do not solve your problem, then consider taking your gun into a gun tech.

First off I want to say it’s hard to trouble shoot technical or mechanical problems over the internet regardless of if ithas to do with guns, cars, computers or pretty much anything where unless you are there in person it’s really hard to figure out the problem.

But I will attempt to address some of the more common issues why a blank gun may not be functioning properly.

Why is my Semi Auto Blank Gun Not Cycling or Ejecting Shells?

One very common reason a blank gun may not be cycling the shells properly is because the owner has removed the barrel restrictor plug. People usually do this to make the barrel opening look more realistic but the barrel restrictor is a necessary component to increase the back pressure allowing the slide to cycle fully to the rear position so it can eject and pickup a new shell.

The blanks you are using may not have enough gun powder in them. Some blank guns require banks with more gun powder than others, again this additional internal pressure forces the slide all the way back, if the blank does not have enough gun powder in it then only a partial slide motion happens and so the discharged shell may not eject properly, in this case the user would have to clear the blank gun manually so another shell can then be picked up and loaded into the breach.

If your blank guns is dirty or not lubricated then it may act sluggish again restricting the full movement of the slide which will effect correct operation. Make sure to thoroughly clean and lubricate your blank gun, that may be a quick fix for you!

You may have a faulty extractor? The extractor is like a hook that grabs the discharged shell while the slide is in the reward position pulling or extracting the shell out of the breach. If the extractor is worn or broken then the empty shell will not be ejected from the breach so when a new shell is picked up from the magazine it has nowhere to go and usually you will get a jam-up in the ejection port area.

One final situation that can cause your blank gun to not cycle properly is to strong of a slide spring, some blank guns out of the box just come with a really heavy slide spring, so much so that even blanks with lots of gunpowder in them are still not strong enough to make the slide operate full motion. Your only option here would be to replace the heavy slide spring with a lighter one.

Why Are My Blanks Not Firing?

This is a situation where you pull the trigger and nothing happens. Lets get the obvious causes right out of the way here… Did you put blanks in your gun and are they new blanks? Did you chamber the first round in your semi auto pistol?

So now that that’s out of the way let’s look at some other reasons why your blank gun may not be firing a blank. Perhaps the firing pin is broken? Most blank guns are not made out of carbon steel and even the firing pins can be lesser quality than what you would find in a real gun so blank guns are more prone to breaking than real guns. I have seen broken firing pins in blank guns first hand so make sure to check the firing pin and that it is fully operational.

Try changing up your blanks to another brand? Again blank gun ammunition is not made to the same higher standards that real firearm ammo is made and some primers may require a little more pressure than your gun is providing. Even with real guns an ammo change may help the gun operate better.

Why is the Trigger or Hammer Not Operating Properly?

I have come across blank guns where there are mechanical problems in the trigger and hammer areas, you may be able to address this yourself but I would recommend taking your blank gun to a gunsmith since you will have to take the gun pretty much full apart to fix a problem in the trigger and hammer areas.

Of course make sure your gun is clean and lubricated, this can help a lot with the mechanical areas of your blank gun.

One problem I saw with a few EKOL Special 99’s was specifically with the single action potion of the trigger, when I would pull the hammer back it would not lock back and the hammer would often slip and fire randomly, this is rather dangerous. When I took the gun apart I found that the table top or step that the trigger was supposed to catch on was worn down on the edge so it would simply slip off. I was able to fix this by filing a new edge on the step area. Again this can happen because blank guns are not made out of as high quality metal materials as real guns.

Why does the Flame Come out the Top of My Blank Gun and Not the Front?

If you find that the flame or discharge comes out of the top of your blank gun and not the barrel, this usually does not mean anything is wrong with your blank gun. All it means is you own a top venting blank gun and not a front firing blank gun. In some countries front firing blank guns are not allowed but front venting blank guns are. The same may also be reversed in some countries, for instance here in Canada we can only import front firing blank guns with flare adaptors since our blank guns are imported under the assumption that they are to be used as signaling or flare devices.

Can I Convert my Top Venting Blank Gun into a Front Venting Blank Gun?

I really don't recommend altering a blank gun in any way as it may be a violation of your local laws and it could cause the blank gun to malfunction in a very bad way causing serious injury or even death!

In theory I suppose it may be possible to convert your Top Venting Blank Gun into a Front Venting Blank Gun but again you would need to allow for just the right amount of back pressure so a wide open barrel would not work unless it was a revolver. You can not simply remove the red plug and bingo you have a front firing blank gun because in most cases the barrel will be completely plugged in the frontal region. Not only would you need to drill out the plugged portion of the barrel but you would also have to somehow fill in the top venting area and again makes sure to allow for just enough back pressure to cycle the slide back and forth.

Hopefully this has helped some of you with blank gun issues. If you’re looking for a blank gun make sure to come down to www.ReplicaAirguns.ca and www.ReplicaAirguns.us and have a look in our blank gun area of our online stores.