Today I decided to get outside since the weather was nice and make my Field Test Shooting Video for the ASG TAC-6 CO2 Airsoft Rifle (actually outside in the filed!) After all the ASG TAC-6 CO2 Airsoft Rifle is a sniper rifle and so I wanted to test it out at longer ranges than my 30 foot indoor shooting range can allow for. So I setup two paper targets at around 40 feet and 80 feet out, the actually distance may have been longer than that?
Starting off my Field Test Review I placed five .25 gram plastic Airsoft BB’s through my Chronograph and averaged 446 fps which is 6 fps faster than the claimed 440 fps from ASG. And that was with .25 gram Airsoft BB’s so if I was using lighter .20 gram BB’s I would expect velocity closer to around 500fps so don’t be shooting anyone with this Airsoft Rifle at close ranges!
Next I proceeded with my accuracy test placing 5 rounds on the target setup around 40 feet downrange. I managed to get all 5 rounds within about 2 inches of each other, not bad since this is a good 10 feet more than I usually test my Airsoft Rifles at. With the remaining 10 rounds in my magazines I was hoping to get at least a couple shots on my paper target setup a good 80 feet away but did not have much luck, I even reloaded the 15 round stick magazine 2 more times and gave it a go but again with no success! The Airsoft BB’s seemed to want to angle off in all direction usually up and to the right or left right before the 80 foot target, perhaps I would have had much better luck at 60 feet?
All I can surmise from this higher range Field Test is that the ASG TAC-6 CO2 Airsoft Rifle is not really a long range Airsoft gun at least with the .25 gram Airsoft BB’s I was using, maybe heavier Airsoft BB’s would settle down a bit more? I can say at ranges up to 40 feet the ASG TAC-6 CO2 Airsoft Rifle did perform just fine so keep that in mind when looking into buying one of these as smoking cans at 30-40 feet will be no problem and make for some fun times in the back yard or even basement makeshift gun range.
Type: Airsoft Rifle. Manufacturer: ASG. Model:TAC-6. Materials: Plastic with some internal metal parts. Weight: 3.5 pounds (1588 grams). Barrel: 12 inches, metal non-rifled. Length: 36 inches. Propulsion: 12 gram CO2 x 1. Action: Semi auto, double action only. Ammunition Type: 6mm BB's. Ammunition Capacity: 15 round metal stick magazine. FPS: 440.
Trigger Pull: The double action only type trigger pull on the ASG TAC-6 CO2 Airsoft Rifle is not too heavy but it is rather long so really quick rapped fire shooting will require some finger work. The trigger reset is right at the begging of the pull so you need to make sure you allow the trigger full range of motion or you may miss the odd shot.
Accuracy: I haven't done my Field Test Shooting video just yet for the ASG TAC-6 CO2 Airsoft Rifle but will shortly so stay posted for that video. ASG claimed the fps to be right around 440 and I am assuming with .20 gram Airsoft BB’s, I will most likely busing .25 gram Airsfto BB’s for my testing so I am hoping for around 400 fps or so. With the fiber optic front sight and fully adjustable rear peep sight I shoudl be able to get some decent rounds on target downrange and hopefully get a nice grouping.
Build Quality: The ASG TAC-6 CO2 Airsoft Rifle is mostly plastic but feels pretty good in the hand with decent fit and finish. There are some metal internal part along with the outer barrel and top rail but for the most part the ASG TAC-6 CO2 Airsoft Rifle is all plastic including the trigger and front and rear sights.
Realism: The ASG TAC-6 CO2 Airsoft Rifle is not a replica of any modern rifle that I know of but it does look a bit like a Beretta CX4 Storm especially the back half of it. The flash hider and top and bottom raise add to the realism. Available From: The Replica Airguns Store.
Pros:
Very customizable with rails top and bottom.
Comes with a rather nice Bipod that can be used with other rifles.
Front and back removable Iron sights are very usable, fiber optic in front, peep in back.
Safety switch is in a great location for right handed shooters.
Canada version comes with black flash hider.
Mostly plastic but solid construction.
Rubber Butt Pad is nice and thick.
Removable barrel to reduce size for easier transportation.
Also come in 4.5mm Steel BB version.
Optional Integrated laser can be added.
Cons:
DOA Trigger pull is a bit long which will slow down rapid fire shooting a bit.
Mostly Plastic Polymer build.
Why not a longer inner barrel for possible more fps?
CO2 is in the Pistol grip and not the magazine so may not be great for on field battles.
Comments: This may not be the most exciting Airsoft Rifle I have reviewed, it does look kind of cool and the price is right compared to other Airsoft Rifles. Who is it really for? I would say someone looking for an Air Rifle for plinking in the backyard or basement that perhaps want's a little bit more safety in terms of using plastic BB’s rather than Steel BB’s. Sure you can use the ASG TAC-6 CO2 Airsoft Rifle for Airsoft wars but most people want something a bit more realistic in terms of looks and function. Because the ASG TAC-6 CO2 Airsoft Rifle does have built-in Popup it shoudl be able to reach out to longer ranges so we will have to see if it can perform decent at longer ranges when I do my Field test Shooting Video.
My YouTube Table Top Review Video for the ASG TAC-6 CO2 Airsoft Rifle:
In this Field Test Shooting Video I put the EMG TTI STI 2011 Combat Master John Wick GBB Airsoft Pistol through its paces to see how well it performs in the Replica Airguns Indoor Sea Can Airgun Shooting Range. I first place 5 rounds through the chronograph to see what the actual real world velocity is and then I shoot 10 rounds on my paper target 30 feet downrange to see how tight of a grouping I can get with it.
For my Chronograph Test I was using .25 gram Airsoft BB’s so the velocity will be a little bit under the claimed 370 using .20 gram Airsoft BB’s. The temperature was average, not hot or cold so right around room temperature. My 5 shot sting resulted in an average of 312 fps so I would guesstimate an additional 50-60 fps using the .20 gram BB’s since the Airsoft BB’s I was using where ab out 20% heavier than what was claimed. So 370 is for sure possible with the EMG TTI STI 2011 Combat Master John Wick GBB Airsoft Pistol.
Going onto my accuracy test, again I used the same .25 gram Airsoft BB’s and placed 10 rounds back to back into my fresh paper target setup 30 feet away. As usually I had my hands resting on a sand bag up front and I was sitting in the back which helps get a fairly stable shooting position but not without some human factor involved. I did manage to place 4 rounds right inside the 1.5 inch bullseye but 6 did come out with my last shot being a bit of a flyer hitting rather low on the target. If I removed the flyer form the equation the EMG TTI STI 2011 Combat Master John Wick GBB Airsoft Pistol did mange to shoot a 3 inch grouping. I do feel I can do better with this Airsoft pistol when I dial in the right Airsoft BB’s, hop-up and of course get a bit more use to shooting it.
All things considered, I really like the EMG TTI STI 2011 Combat Master John Wick GBB Airsoft Pistol! It has one of the best triggers I have ever reviewed with a nice combination of short take up and light predictable trigger release. The blowback action is fast yet not overwhelming and the overall feel of shooting this gun is very satisfying. Make sure to also checkout my Table Top Video Review for the EMG TTI STI 2011 Combat Master John Wick GBB Airsoft Pistol where I go into more details about the specifications and features along with some nice close up video.
Type: GBB Airsoft Pistol. Manufacturer: Made by EMG. Model:TTI STI 2011 Combat Master. Materials: Aluminum & polymer components. Weight: 2.4 pounds (1100 grams). Barrel: 5 inches (127mm) metal non-rifled. Propulsion: Green gas. Action: Semi auto blowback, single action only trigger. Ammunition Type: 6mm plastic Airsoft BB's. Ammunition Capacity: 28 round drop out full size metal magazine. FPS: Claimed 370.
Trigger Pull: The single action only trigger pull on the EMG TTI STI 2011 Combat Master is really great, there is virtually zero take-up with a light, crisp and easy release. You can double tap with ease making the EMG TTI STI 2011 Combat Master a great action pistol. One of the shortest and smoothest 1911 triggers I have tested, at least up there with the best for sure!
Accuracy: At this point I have not shot the EMG TTI STI 2011 Combat Master so I have no idea what the actual real world fps is going to be and how accurate it proves itself so my comments for this part of the review will ahed to wait till I perform my Field Test Shooting Video coming up shortly…
Build Quality: TheEMG TTI STI 2011 Combat Master is for the most part an all metal gun with a CNC Machined Aluminum Slide and metal slide along with mostly ,metal parts throughout. The guide rod is stainless steel and the barrel is also aluminum with an anodized rose gold finish. The fit and finish is awesome on the EMG TTI STI 2011 Combat Master with attention to detail everywhere. The only plastic I could find on this Airsoft pistol would be the grips and the skeletonized trigger.
Realism: The EMG TTI STI 2011 Combat Master is based off of the STI 2011 but is really a replica of the John Wick pistol used in the John Wick 3 movie and is virtually the spitting image to it. You will find licensing and trademarks where you would find them on the real steel version. Of course all the mechanical parts work like the real version and the EMG TTI STI 2011 Combat Master can be fully field stripped.
Pros:
Super crisp, light and short SAO trigger.
Fit and finish is excellent, very little slide wiggle.
Extremely close replica of the custom STI 2011 pistol used in the John Wick 3 movie.
Rear sight is fully adjustable and is not too bulky.
Fiber optic front sight helps with quick targets acquisition.
CNC machined two tone Aluminum slide with metal frame.
Rose Gold barrel looks great!
Full size high capacity 28 round double stack metal magazine.
Ambidextrous thumb safeties.
Working grip safety as you would expect on a 1911 based gun.
Most Mechanical parts work just like a steel version and can be easily field stripped to access hop-up.
Super crisp and fast blowback action, great for action shooting.
Licensing all over this gun true to the real steel version..
Cons:
Comes with the red tip but can be remove pretty easily.
Need a tool to remove the two part guide rod and barrel (don’t lose the screw!).
No dot’s on the rear sight.
Comments:
The EMG TTI STI 2011 Combat Master has got to be one of the most gorgeous and sticking Airsoft Pistols I have reviewed so far. Just everything about this pistol looks and feel great. For a $299 Canadian Pistol you get a really well made high quality product that will be a collectors item to own for years to come. It’s not a small or light gun but for it’s size it feels really well balanced in the hand but for those with small hands it may be a bit too much of a handful. If you see them in stock on our website, make sure to grab one while you can!
In this Update Preview Unboxing Video I take a look at 5 products that came across my table and that I have not reviewed so far on the Replica Airguns YouTube channel.
First I show off an HPA tank from Air Venturi that works perfectly for the Sig Sauer MPX and MCX Pellet Rifles allowing for more consistent fps and I would image a higher overall fps? We will find out when I test it out in the replica Airguns Indoor Sea Can Airgun Range.
13 Oz Aluminum
10 Inches Long
2 Inches Diameter
Integrated Pressure Gauge
Includes Buttstock
CO2 Adaptor Included
3000 PSI Fill
1100 PSI Regulated
Next I take a look at the KJWorks M9A1 GBB Airsoft Pistol, I hover revived the CO2 version before but this version comes with the Gas magazine rather than the CO2 mag for those that prefer gas operated Blowback Airsoft Pistols. Because of the slightly lower FPS the Gas version comes with a barrel extension to make it Canada import friendly.
6mm Airsoft BB’s
Green Gas / Propane
370 fps
25 Round Magazine
2 Pounds
Probably one of the most interesting product I look at in this video at least for me is the EMG JW3 Combat Master GBB Airsoft Pistol. This Airsoft pistol is mainly aluminum with some polymer based off of the 2011 STI and was featured in the 2019 John Wick 3 Film. I’m really looking forward to testing this one out in the Sea Can Replica Airguns Airgun Range!
6mm Airsoft BB’s
Green Gas / Propane
9.4 Inches
366 fps
28 Round Magazine
2.4 Pounds
Moving along to another Air Pistol I finally get my hands on the Crosman P1 which is really just a KWC PT92 4.5mm Blowback CO2 BB Pistol but with Crosman Branding and an included laser. Since I have never shot a PT92 BB Pistol with a laser I will probably make a Field Test Shooting Video to see how well it performs.
4.5 mm Steel BB’s
CO2 x 1
4.2 Inch Barrel
330 fps
19 Round Magazine
2.4 Pounds
Comes with Laser Sight
Last up I take a look at the ASG TAC-6 which is pretty much the exact same ASG TAC-4.5 CO2 Air Rifle I tested a while back but in this case the 6 refers to it being a 6mm Airsoft Rifle rather than a 4.5mm Steel BB Riffle. I am not sure I will do a full Table Top Video since these guns are virtually identical but just in different Ammo types but I hope to get outside and see how well it performs shooting at a bit more distance than the 30 foot indoor range I usually test my Airgun in.
This Table Top Comparison video is also a bit of a revisit since I reviewed the US version of the Sig Sauer ASP MPX .177 Cal. Pellet Rifle back in 2016 when it first came out. I actually had to go across the border and bring it back across with me which can be a lot of fun dealing with Canada Customs border agents. They are well meaning but often don’t fully understand their own import guidelines for Airguns. After about an hour or so I was able to convict the CBSA officer that no my Sig Sauer Airguns where not regulated Firearms and no they did not require any registration or transfer permits.
Anyway that was 5 years ago and now we have the Canada import version which makes purchasing one of the Sig Sauer ASP MPX .177 Cal. Pellet Rifles so much easier and to be honest there really isn’t any difference as far as I can tell since my original US version even though it had a claimed fps of up to 600 was actually closer to somewhere in the mid 400’s using standard .177 caliber lead pellets.
Below are the basic specifications and if you want more info than that either watch the video or checkout my Original Table Top Review for the Sig Sauer ASP MPX .177 Cal. Pellet Rifle since both the original US and newer Canada versions are virtually identical…
Type: Pellet Rifle. Manufacturer: Sig Sauer ASP Model: Sig Sauer MPX ASP Materials: Metal and Nylon Fiber build. Weight: 7 Pounds (3300 Grams). Barrel: 8 inch steelrifled. Propulsion: 88 or 90 Gram CO2. Action: Semi Auto,double action only. Ammunition Type: .177 caliber pellets. Ammunition Capacity: 30 rounds belt fed. FPS: Up to 575-600 fps (When shot by a Unicorn) Probably closer to around 450fps
I will be following this Tabel Top Review for the US and Canada Sig Sauer ASP MPX .177 Cal. Pellet Rifles with a Field Test Shooting Comparison to see if anything has really changed interns of velocity and accuracy so stay posted for that video coming out very soon…
It was a decent day today, not too cold and not raining at least at the time I and ethics video :) I figured with my new Insta60 One R and iVUE Vista cameras it would be a great day to test them out outside shooting with my G&G SMC-9 Full Auto Airsoft Carbine. I like the bak for more regulated Indoor Field Tests, these outside usually clay pigeon shooting videos are a lot more fun and I think a nice break for everyone.
So in this video I have three cameras rolling and switch camera switch back and forth throughout the video to make the experience more immersive. I have cameras setup front and back (Sony RX100 IV in front & Sony HDR-AS15 Back), along with my iVUE camera glasses and my Insta360 One R mounted to the barrel of my G&G SMC-9. All in all I think the video turned out well. It may be time to upgrade my Sony Action Camera as it is probably the oldest camera in my collection and you can see in the video it does not look as good as the other cameras.
In this Field Test Shooting Video I test out the G&G SMC-9 GBB Airsoft Carbine in the Replica Airguns Indoor Sea Can Airgun Shooting Range to see if the real world performance matches the manufacturers claims. I first place 5 rounds through my Chronograph using .25 gram Airsoft BB’s with a fully gassed up extended magazine to find out what the actual FPS is. I then shoot 10 rounds from a seated and rested shooting position into a fresh paper target setup 30 feet down range to see just what we can expect and then just for fun I shoot the 40 rounds left in the 50 round magazine in full auto to see how this also effects accuracy.
Starting with my Chronograph test, the G&G SMC-9 GBB Airsoft Carbine averaged 339 FPS with the fastest shot recorded at 350 fps and the slowest being 324 fps, so very consistent in terms of sustained fps during my Chronograph velocity testing. The velocity was a bit under the claimed 366-375 fps but I was using slightly heavier BB’s and it wasn’t super warm temperatures in the Sea Can on this testing day, around room temperature, (20 degrees Celsius or 68 degrees Fahrenheit).
Moving onto the accuracy testing for the G&G SMC-9 GBB Airsoft Carbine, it performed pretty decent shooting about a 10 round 4 inch grouping but if I removed two flyers top and bottom the grouping would have been loser to 1.5 inches. The grouping was well centered on the target but I did adjust the sights up a bit as initially out of the box the G&G SMC-9 GBB Airsoft Carbine was shooting fairly low at 30 feet out. The good news is the G&G SMC-9 GBB Airsoft Carbine has fully adjustable sights for windage and elevation along with the 120 clicks of hop-up adjustment. When it came to my full auto testing I found I was shooting really low, perhaps from the blowback recoil pushing me of target? This was the case at least when I did a 40 round mag dump. When I performed the test using shorter bursts I was able to keep more rounds centered on the target for sure but accuracy in full auto was not nearly as good as in semi auto because of the heavy blowback.
Over all the G&G SMC-9 GBB Airsoft Carbine performed decent for me, the velocity was bang on right around what is claimed by G&G allowing this GBB Airsoft Carbine to shoot targets at further out ranges. Accuracy in semi auto was also very good but again shooting in full auto will take a bit more of your attention keeping the blowback recoil under control, for this reason burst fire in full auto will give you better accuracy which is more than likely how you would be shooting the G&G SMC-9 GBB Airsoft Carbine anyways. I really like the diversity you get with the G&G SMC-9 GBB Airsoft Carbine and if you are into Gas Blowback Airsoft guns, then I feel you get similar performance to an AEG but with a lower capacity magazines, but then again I may just have to get my hands on a drum magazine for the G&G SMC-9 GBB Airsoft Carbine and see how that changes things.
Type: Gas Blowback Airsoft Carbine. Manufacturer: G&G Model: SMC-9 Materials: Metal/Aluminum & Polymer. Weight: 4.7 pounds (2125 grams). Length: 410/620mm folded/unfolded length Hop-up: Yes - 120 click adjustment. Propulsion: Green gas or propane. Action: Semi & Full AutoBlowback, single action only. Ammunition Type: 6mm plastic Airsoft BB's. Ammunition Capacity: 50 rounds. FPS: 366-375 fps.
Trigger Pull: The trigger pull on the G&G SMC-9 GBB Airsoft Carbine is typical single action only with a soft short take-up and light release point. I would not call this a crips trigger since it does have a rather spongy feel to it but this is only noticeable when you are easing the trigger slowly. In reality you will be engaging the trigger quickly when shooting it on the field and won’t notice any of the creep or take-up. I would consider it to be a decent trigger pull over all.
Accuracy: I have not done my actual Field Test Shooting video review for the G&G SMC-9 GBB Airsoft Carbine but as with most of my Full auto Airguns I find it hard not resist going outside and blasting off at least one magazine in full auto. Of course this was the case with the G&G SMC-9 GBB Airsoft Carbine and I can tell you I went through all 50 rounds in not time and the G&G SMC-9 GBB Airsoft Carbine rounds went exactly where I pointed the gun short and long range so I expect my Field Test Shooting video to produce good results.
Build Quality: The G&G SMC-9 GBB Airsoft Carbine feels amazing in the hand with a lot of metal going on in the upper Carbine conversion kit portion, the front rail assembly is CNC Aluminum and the Pop-up iron sights are actually metal. The rear fold out stock is plastic but it is sold and just like the rest of the G&G SMC-9 GBB Airsoft Carbine very well made with great fit and finish. Of course the lower polymer frame is from the G&G GTP9 and just like all of the G&G pistols is very well made.
Realism: The G&G SMC-9 GBB Airsoft Carbine genuinely feels like a real steel firearm when holding it in the hand. Shooting it feels much the same but obviously with a lot less recoil than a powder burner. Just like a real steel 9mm Carbine the G&G SMC-9 GBB Airsoft Carbine mechanically works virtually the same with working slide catch release, charging handles, magazine release, and duel safeties, all ambidextrous by the way. As expected you can fully field strip the G&G SMC-9 GBB Airsoft Carbine.
Lots of metal parts giving the G&G SMC-9 GBB Airsoft Carbine really good weigth and feel.
Fold out stock sits nice and tight using magnets when not in use.
Integrated QD sling swivel.
Comes with two different sized Back-straps to accommodate small and larger hands.
Super high capacity extended 50 round magazine that holds a ton of gas for consistent power and lots of shots per fill.
Converts the standard GTP9 semi auto pistol into a full auto Carbine.
Almost everything is ambidextrous.
CNC 20mm / MLOK Rail for lots of accessories options.
Actual metal pop-up fully adjustable sights.
Easy to adjust hop-up without disassembly.
Dual safety system, cross bolt on frame and trigger safety.
Cons:
Fold out stock is not adjustable which makes the sights are a bit tight.
Does not come with the pistol slide if you want to covert it back to the GTP9.
Comments:
I am a big fan of the full line of G&G Airsoft guns and so far their GBB pistol lineup has been a treat to review, adding their new G&G SMC-9 GBB Airsoft Carbine to the lineup for me is the perfect mix between their GBB Pistol lineup and their mostly AEG Rifle lineup. I am hoping to see if I can acquire the drum magazine and eventually see how that works with the G&G SMC-9 GBB Airsoft Carbine, for now the 50 round extended magazine will have to do. Really looking forward to testing out the G&G SMC-9 GBB Airsoft Carbine so stay posted for those results shortly!
My YouTube Table Top Review of the G&G SMC-9 GBB Airsoft Carbine:
In this Field Test Shooting Video I test out the G&G Piranha MK I & TR GBB Airsoft Pistols in the Replica Airguns Indoor Sea Can Airgun Shooting Range to see what the real world performance is for these very similar Airsoft Pistols. I first place 5 rounds through my Chronograph for each Airsoft Gun using .25 gram Airsoft BB’s with fully gassed up magazines to find out what the actual fps velocity is. I then shoot 10 rounds from a seated and rested shooting position into fresh paper targets setup 30 feet down range to see just what we can expect in terms of accuracy from the G&G Piranha series.
Starting with my Chronograph test, a placed 5 rounds through my Chronograph with both the G&G Piranha MK I and G&G Piranha TR GBB Airsoft Pistols. Technically they should have performed nearly identical but not all guns are setup exactly the same out of the box and so the G&G Piranha MK I GBB Airsoft Pistol did shoot a bit hotter than the G&G Piranha & TR GBB Airsoft Pistol averaging 290 fps versus 257 fps. As a quick test I placed the magazine from the MK I into the TR and the G&G Piranha TR GBB Airsoft Pistol did shoot much hotter and very close to the G&G Piranha MK resultsI. I would assume the valves in these magazines where perhaps not letting out the same amount of Gas hence the difference in velocity. The velocity was well under the claimed 370+but I was using slightly heavier BB’s and it was a little cold in the Sea Can on this testing day, not quite room temperature. Around 19 degrees Celsius or 66 degrees Fahrenheit.
Moving onto the accuracy testing for the G&G Piranha MK I & TR GBB Airsoft Pistols, they performed pretty well shooting 10 round 2 inch groupings with both Airsoft Pistols shooting on the money vertically while the G&G Piranha MK I shot a bit to the left and the G&G Piranha TR shooting well centered all around.
All in both of the G&G Piranha MK I & TR GBB Airsoft Pistols performed good for me, I would have liked to have seen the fps higher since both guns where well under the claimed 370+ fps but for close quarter shooting you should have no problem with either of them and again maybe your magazine will shoot a bit hotter than mine did. The partial blowback action is snappy and quick with just enough recoil action to give that realistic shooting experience. The triggers on the G&G Piranha MK I & TR GBB Airsoft Pistols are really nice allowing for quick tight followup shots and again if you like the look and feel of a Glock but perhaps want something a bit more unique then you will want to consider one of the G&G Piranha series Airsoft Pistols know doubt.
In this Field Test Shooting Video I test out the G&G GPM92 GP2 GBB Airsoft Pistol in the Replica Airguns Indoor Sea Can Airgun Shooting Range to see what the real world performance is for this Beretta 92 styled G&G Airsoft Pistol. I first place 5 rounds through my Chronograph using .25 gram Airsoft BB’s with a fully gassed up magazine to find out what the actual FPS is. I then shoot 10 rounds from a seated and rested shooting position into a fresh paper target setup 30 feet down range to see just what we can expect in terms of accuracy from the G&G GPM92 GP2 GBB Airsoft Pistol.
Starting with my Chronograph test, the G&G GPM92 GP2 GBB Airsoft Pistol averaged 275 FPS with the fastest shot recorded at 278 FPS and the slowest being 274 FPS, so very consistent in terms of sustained FPS doing my testing. The velocity was well under the claimed 366 but I was using slightly heavier BB’s and it was a little cold in the Sea Can on this testing day, not quite room temperature. Around 19 degrees Celsius or 66 degrees Fahrenheit.
Moving onto the accuracy testing for the G&G GPM92 GP2 GBB Airsoft Pistol, it performed pretty decent shooting about a 10 round 1.5 inch grouping if I removed one flyer that pulled a bit to the left. The grouping was a little bit low but well centered left and right so even though the sights are none adjustable I should be able to pull up the shot placement a bit using the hop-up adjustment.
All in all the G&G GPM92 GP2 GBB Airsoft Pistol performed well for me, I would have liked to see the FPS just a bit higher but for close quarter shooting you should have no problem with it. The blowback action is nice and firm and the typical Beretta single and double action trigger is true to form allowing for a round in the pipe with the hammer safely decocted but ready to go with a quick release of the safety and a double action pull of the first round. The G&G GPM92 GP2 GBB Airsoft Pistol may be a bit bulky and heavy for some smaller handed shooter so keep that in mind.
Type: Gas Blowback Airsoft Pistol. Manufacturer: G&G Model: Piranha TR Materials: Metal & Polymer. Weight: 1.5 pounds (670 grams). Length: 7.8 inches total Barrel: 4.01 inches,Metal non-rifled smooth bore. Propulsion: Green gas or propane. Action: Blowback, single action only. Ammunition Type: 6mm plastic Airsoft BB's. Ammunition Capacity: 25rounds. FPS: 370+ fps.
Trigger Pull: The trigger pull on the G&G Piranha TR GBB Airsoft Pistol is typical single action only with a easy short take up (some of which is the trigger safety engaging), followed by a crisp predictable light release. The quick slide cycle allows for quick semi auto shooting with the G&G Piranha TR GBB Airsoft Pistol making it a great fast action shooter with quick target acquisition between shots.
Accuracy: I have not done my actual Field Test Shooting video review for the G&G Piranha TR GBB Airsoft Pistol but I expect it to perform similar to most G&G Blowback Gas Operated Airsoft Pistols and shoot consistently in the mid 300 fps with a 10 round grouping around 1-2 inches. Stay posted for my Field Test Shooting Video where I hope to confirm these predictions in the Sea Can indoor Airgun Shooting Range.
Build Quality: Like most off theG&G Airsoft guns, the G&G Piranha TR GBB Airsoft Pistol build quality is really nice. Fit and finish are excellent with virtually zero slide wiggle, you can also get the G&G Piranha TR GBB Airsoft Pistol in a two tone stainless slide and chrome finish barrel that looks really sharp. It also has an updated Ceramic Whirl Cylinder Valve technology from G&G that should significantly help with freezing in colder or fast shooting situations along with a new Hop-up system you can easily adjust using a special tool without taking the Airsoft gun apart.
Realism: The G&G Piranha TR GBB Airsoft Pistol as far as I can determines not an exact replica of any specific real steel gun in production but it does share looks, size and feel to that of the Glock but perhaps with an even more modernized look to it. You will find realistic function to the G&G Piranha MK I GBB Airsoft Pistoling terms of it’s operation with its full blowback action, working slide catch release, magazine release trigger safety and takedown lever allowing for it to be easily and quickly field stripped.
Good balance of metal and plastic for a balanced and light feel.
Partial slide Blowback operation should allow for even better gas performance and snappy operation.
Ceramic Whirl Cylinder Valve should expect to get decent amount of shots per green gas fill.
White dot sights front and back.
Nice two tone slide.
Has a working trigger safety.
Smaller spit grip perfect for people smaller hands.
Comes with hard shell case.
New Hop-up system for quick and easy fine adjustments with no need to field strip the gun.
Dual 20mm top and bottom Rails for accessories.
Comes in all black and two tone black and sliver.
Comes with high quality speed loader
Threaded barrel tip for add on mock suppressor.
Cons:
Sights are non adjustable.
Not an actual replica of any specific gun I know of but does share some Glock attributes.
No actual frame safety other than the trigger safeties, (not always a bad thing).
Comments:
Overall I really like the new G&G Piranha TR GBB Airsoft Pistol, it has a really modern look to it yet has a familiar feel. The G&G Piranha TR GBB Airsoft Pistol is fairly light weight with that quick and snappy partial slide allowing for very quick follow up shots. Combine all of that with the new Gas saving Ceramic Whirl Cylinder Valve I expect the G&G Piranha TR GBB Airsoft Pistol to perform really well when in action. I like that you have the option of the more subdued all black version or if you like your guns to be a little bit more flashy you can also get it in the two tone with black and stainless version. The TR version over MK 1 does allow for optics on top which personally would not be my choice for this gun but it’s nice that you have this option.
My Table Top Review Video of the G&G Piranha TR GBB Airsoft Pistol:
Type: Gas Blowback Airsoft Pistol. Manufacturer: G&G Model: Piranha MK I Materials: Metal & Polymer. Weight: 1.5 pounds (670 grams). Length: 7.8 inches total Barrel: 4.01 inches,Metal non-rifled smooth bore. Propulsion: Green gas or propane. Action: Blowback, single action only. Ammunition Type: 6mm plastic Airsoft BB's. Ammunition Capacity: 25rounds. FPS: 370+ fps.
Trigger Pull: The trigger pull on the G&G Piranha MK I GBB Airsoft Pistol is typical single action only with a easy short take up (some of which is the trigger safety engaging), followed by a crisp predictable light release. The quick slide cycle allows for some pretty quick semi auto shooting with the G&G Piranha MK I GBB Airsoft Pistol making it a great fast action shooter.
Accuracy: I have not done my actual Field Test Shooting video review for the G&G Piranha MK I GBB Airsoft Pistol but I expect it to perform similar to most G&G Blowback Gas Operated Airsoft Pistols and shoot consistently in the mid 300 fps with a 10 round grouping around 1-2 inches. Stay posted for my Field Test Shooting Video where I will confirm these predictions.
Build Quality: Like pretty much all G&G Airsoft guns, the G&G Piranha MK I GBB Airsoft Pistol build quality is really good. Fit and finish are excellent with virtually zero slide wiggle, the two tone stainless slide and chrome finish barrel look really good. It also has an updated Ceramic Whirl Cylinder Valve technology from G&G that should significantly help with freezing in colder or fast shooting situations along with a new Hop-up system you can easily adjust without taking the Airsoft gun apart.
Realism: The G&G Piranha MK I GBB Airsoft Pistol as far as I can determines not an exact replica of any specific real steel gun in production but it does share looks, size and feel to that of the Glock but perhaps with an even more modernized look to it. You will find realistic function to the G&G Piranha MK I GBB Airsoft Pistoling terms of it’s operation with its full blowback action, working slide catch release, magazine release trigger safety and takedown lever allowing for it to be field stripped.
Good balance of metal and plastic for a balanced and light feel.
Partial slide Blowback operation should allow for even better gas performance and snappy operation.
Ceramic Whirl Cylinder Valve should expect to get decent amount of shots per green gas fill.
White dot sights front and back.
Nice two tone slide.
Has a working trigger safety.
Smaller spit grip perfect for people smaller hands.
Comes with hard shell case.
New Hop-up system for quick and easy fine adjustments with no need to field strip the gun.
20mm Rail for accessories.
Comes in all black and two tone black and sliver.
Comes with high quality speed loader
Threaded barrel tip for add on mock suppressor.
Cons:
Sights are non adjustable.
Not an actual replica of any specific gun I know of but does share some Glock attributes.
No actual frame safety other than the trigger safeties, (not always a bad thing).
Comments:
Overall I really like the new G&G Piranha MK I GBB Airsoft Pistol, it has a really modern look to it yet has a familiar feel. The G&G Piranha MK I GBB Airsoft Pistol is fairly light weight with a quick and snappy slide allowing for very quick follow up shots. Combine all of that with the new Gas saving Ceramic Whirl Cylinder Valve I expect the G&G Piranha MK I GBB Airsoft Pistol to perform really well when in action. I like that you have the option of the more subdued all black version or if you like your guns to be a little bit more flashy you can also get it in the two tone with black and stainless version.
My Table Top Review Video of the G&G Piranha MK I GBB Airsoft Pistol:
Type: Gas Blowback Airsoft Pistol. Manufacturer: G&G Model: GPM92 GP2 Materials: Metal slide & frame, real wood grips. Weight: 2.3 pounds (1040 grams). Length: 8.9 inches total Barrel: 4.6 inches,Metal non-rifled smooth bore. Propulsion: Green gas or propane. Action: Blowback, single and double action. Ammunition Type: 6mm plastic Airsoft BB's. Ammunition Capacity: 28rounds. FPS: 366+ fps.
Trigger Pull: The trigger pull on the G&G GPM92 GP2 GBB Airsoft Pistol is very good in both single and double action. Double action is a bit longer but not that much heavier when shooting in single action. Single action shooting is short, light and crisp as you would expect when shooting a real steel Beretta 92 style pistol.
Accuracy: I have not done my actual Field Test Shooting video review for the G&G GPM92 GP2 GBB Airsoft Pistol but it should perform similar to my earlier review of the G&G GPM92 GBB Airsoft Pistol where it performed fairly well shooting in the mid 300 fps with a nice under 1 inch 10 round shot placement for 30 feet down range.
Build Quality: Like pretty much all G&G Airsoft guns, the G&G GPM92 GP2 GBB Airsoft Pistol build quality is right inline. Fit and finish where excellent and a lot of attention to detail was seen all over this Replica Airsoft Pistol. It also has an updated Ceramic Whirl Cylinder Valve technology from G&G that should significantly help with freezing in colder or fast shooting situations along with a new Hop-up system you can easily adjust without taking the Airsoft gun apart.
Realism: The G&G GPM92 GP2 GBB Airsoft Pistol is an excellent replica of the real steel Beretta Mod. 92FS, the safety even acts as a working de-cocker. You'll also find 5, 10, and 15 numbered markings on the backside of the magazine that would normally indicate how many bullets are in the magazine, a nice touch for sure! Everything works pretty much the same as it would on a real Beretta M9 including the ability to fully field strip the G&G GPM92 GP2 GBB Airsoft Pistol. I like the addition of th real wood grips that are a bit thicker than the plastic ones but if you ahed decent sized hands this shoudl not be a problem for you.
Ceramic Whirl Cylinder Valve should expect to get decent amount of shots per green gas fill.
White dot sights front and back.
Nice real wood grips.
Comes with hard shell case.
New Hop-up system for quick and easy fine adjustments with no need to field strip the gun.
20mm Rail for accessories.
comes in three different color schemes. Black, Silver, Gold.
Comes with high quality speed loader
Safety also works as a de-cocker.
Threaded removable barrel tip for add on mock suppressor.
Cons:
Sights are non adjustable.
Wood grips make the grips a bit thicker than plastic grips.
Price does go up especially if yo want the silver or gold version.
Comments:
I would have to say the new G&G GPM92 GP2 is one of the nicest Beretta Model 92FS Airsoft Pistols you are going to find out there, even a step up over the previous GPM92 model. There is a ton of attention to detail for sure, You also get the hard shell case with included high quality speed loader and G&G's updated Ceramic Valve and Revolutionary Whirl Cylinder Valve that help with freeze-up issues. It’s also nice that you no longer are required to filed strip the G&G GPM92 GP2 GBB Airsoft Pistol in order to adjust hop-up and the real wood grips just really finish off this quality product from G&G.
My Table Top Review of the G&G GPM92 GP2 GBB Airsoft Pistol:
In this Preview Unboxing Video I take a look at five Gas Blowback Airsoft Pistols. Three of them are from G&G and two are from ICS. All offer full blowback operation and are green gas or propane powered with full size metal drop out magazines.
I am super excite to showcase three awesome rifles in this Update Preview Unboxing Video. Two of which are Airsoft and one is a Steel BB shooter, all of which are semi and full auto selectable. In this video I do a bit of an unboxing and preview of each Rifle not going into too much detail as I want to leave most of the information for my Table Top and Filed Test Videos. The main purpose of this video is to let everyone know we have these Rifles in our Canada Replica Airguns Store now for sale.
I may as well talk about them in the order they appear in my video so lets start with the ICS CXP APE AEG Airsoft Rifle. The ICS CXP APE AEG Airsoft Rifle is a mostly metal Electric Airsoft Rifle with realistic electronic blowback operation along with a CNC machined aluminum upper and lower receiver. It comes with a hi-cap 300 round magazine and a Ver 2 Full Metal ICS Split Type Gearbox. The ICS CXP APE AEG Airsoft Rifle weighs in at just under 3kg.
Next I showcase the G&G SMC9 GBB Airsoft Carbine, a unique product that converts the G&G GTP9 pistol into a a semi and full auto Carbine and includes a 50 round extended magazine, there is an even higher capacity drum magazine made for this product! You will find a fold out stock along with a CNC Machined MLOK Rail for additional mounting options.
Last but perhaps one that I have been the most eagerly anticipating is the Crosman AK1 CO2 Blowback BB Rifle a twin CO2 Blowback 4.5mm Semi and Full auto AK style BB Rifle, finally a decent AK BB Rifle! The Crosman AK1 CO2 Blowback BB Rifle has a claimed fps of 430 and shoots 1400 rounds per minute in full auto, very similar to the Crosman DPMS series of AR styled CO2 Blowback Full Auto BB Rifles. The Crosman AK1 CO2 Blowback BB Rifle comes with a 25 round magazine and swing out rear adjustable stock.
Make sure to watch my Table Top Review for the Diana Bandit PCP .177 Caliber Bolt Action Pellet Pistol if you haven’t already done so to get all the specifications and features along with some nice close up video. In this Field Test Shooting video I test out the Diana Bandit PCP .177 Caliber Bolt Action Pellet Pistol to find out what the real world velocity is and also just how accurate it will be shooting a paper target from 30 feet back using a rested shooting position. Since the Diana Bandit PCP .177 Caliber Bolt Action Pellet Pistol is a target pistol I was hoping for good accuracy since the Diana Chaser performed so well for me in my earlier Field Test Shooting video this week. The Diana Bandit does have a claimed 700 fps velocity but I believe this is for the non-Canada detuned version so it will be interesting to find out exactly what the power is.
First up I placed 5 shots through my Chronograph with a fully charged PCP tank using 6.9 grain RWS lead pellets and got just over 500 fps results averaging 517 fps, so yes the Diana Bandit PCP .177 Caliber Bolt Action Pellet Pistol has been detuned to make it Canada non-regulated legal.
Next I performed my accuracy test shooting at a paper target 30 feet down range with the Diana Bandit PCP .177 Caliber Bolt Action Pellet Pistol rested on a sand bag up front and sitting in the back. Since the magazine holds 9 rounds I placed 9 round on the target to see what kind of grouping I could get. At first I was not sure why my 9 shot grouping seemed to be much more spread out than My Dianna Chaser results but after watching the video I saw that only one shot really came out of the 1 inch grouping not including the random accident shot I took. Perhaps I had a misinformed pellet or perhaps I pulled that one shot. That shot aside both the Diana Bandit and Chaser performed about the same, even shooting just a hair to the left from the bullseye.
The trigger feels pretty decent, not super light or to heavy, there is a little bit of take-up and then a slight resistance then a quick release. The bolt action along with the 9 round rotary magazine worked flawlessly for me with no jamming at all. For the low price this PCP Target Pellet Pistol comes in at you really can’t go wrong and if you want to modify or upgrade it down the road there are tons of things you can do to the Diana Bandit PCP .177 Caliber Bolt Action Pellet Pistol. I highly recommend the Diana Bandit PCP .177 Caliber Bolt Action Pellet Pistol if you are looking for a super affordable PCP target pellet pistol.
Make sure to watch my Table Top Review for the Diana Chaser CO2 .177 Caliber Bolt Action Pellet Pistol if you haven’t already to get all the specifications and features along with some nice close up video. In this Field Test Shooting video I test out the Diana Chaser CO2 .177 Caliber Bolt Action Pellet Pistol to find out what the real world velocity is and also just how accurate it will be shooting a paper target from 30 feet back using a rested shooting position. Since the Diana Chaser CO2 .177 Caliber Bolt Action Pellet Pistol is a target pistol I was hoping for good accuracy but based on the claimed 525 fps velocity I was also hoping for close to 500 fps results.
First up I placed 4 shots through my Chronograph using a brand new CO2 along with 6.9 grain RWS lead pellets and got pretty close to 500 fps results averaging 490 fps, not bad considering the temperature was not super warm and I was using led pellets not hyper velocity alloy pellets.
Next I performed my accuracy test shooting at a paper target 30 feet down range with the Diana Chaser CO2 .177 Caliber Bolt Action Pellet Pistol rested on a sand bag up front and sitting in the back. Since the magazine holds 9 rounds I placed 9 round on the target to see what kind of grouping I could get. I was impressed to see a nice 1 inch grouping, maybe even a little bit less removing the paper tearing. Shots where vertically right on the mark and just a tad to the left but easily fixable with a quick tweak of the full adjustable sights.
The trigger feels pretty decent, not super light or to heavy , there is a little bit of take up and then a slight resistance then a quick release. The bolt action along with the 9 round rotary magazine worked flawlessly for me with no jamming at all. For the low price this CO2 Target Pellet Pistol comes in at you really can’t go wrong and if you want to modify or upgrade it down the road there are tons of things you can do to the Diana Chaser CO2 .177 Caliber Bolt Action Pellet Pistol. I highly recommend the Diana Chaser CO2 .177 Caliber Bolt Action Pellet Pistol if you are looking for a super affordable target pellet pistol.
Type: Pellet Pistol Manufacturer:Diana. Model:Bandit Materials: Wood and Metal, some plastic. Weight: 2.2 pounds (1000 grams). Total Length: 20.1 inches (51 cm) Barrel: 9.5 inches (24 cm), metal rifled. Propulsion: PCP. Action: Bolt. Ammunition Type: .177 & .22 Caliber pellets. Ammunition Capacity: Single shot to 9 & 7 round magazines.. FPS: 725 (.177) - 630 (.22). Need to test for Canada import version
Trigger Pull: The trigger pull on Diana Bandit PCP .177 Caliber Bolt Action Pellet Pistol is single action only meaning in order to cock the internal hammer/striker, you need to cycle the bolt back and forth allowing for a short and light trigger action. It does come with a rotary multi-round magazine that allows for the cycling of the bolt to automatically advance a pellet allowing for much quicker followup shots.
Accuracy: At this point I have not personally tested the Diana Bandit PCP .177 Caliber Bolt Action Pellet Pistol in terms of actual power and accuracy but I expect the Diana Bandit PCP .177 Caliber Bolt Action Pellet Pistol to perform well since in fact this is a target pistol with fairly high claimed fps. In the next few weeks I plan on making my Field Test Shooting Video so stay posted for the results from that video for confirmation of the performance.
Build Quality: The Diana Bandit PCP .177 Caliber Bolt Action Pellet Pistol is made in China which might make you wonder about the overall quality of this target pistol but after taking a good look around and working all the mechanical parts I ma very impressed with the overall quality and chosen material that went into the production of the Diana Bandit PCP .177 Caliber Bolt Action Pellet Pistol. You will finds metal where you need it as in the barrel, bolt and trigger. The pistol grip are made of wood but you will find some portions of the sights are plastic but it would have been nice if they where all metal.
Realism: Realism isn’t really a concern with the Diana Bandit PCP .177 Caliber Bolt Action Pellet Pistol since it is not a Replica Airguns but in terms of looking like a gun it serves that purpose, no mistaken that so no waving it around in public or things may not turn out so good for you…
Pros:
Inexpensive fairly high quality full featured target pistol for the price.
Expect good accuracy!
Metal construction where it needs to be (Bolt, barrel, trigger).
Rifled barrel.
Fully adjustable sights.
Adjustable and light single action trigger.
Dove tail on bolt for adding optical sight.
Nice wood pistol grip.
Good for small pest control because of fairly high fps and expected good accuracy for shot placement ability.
Overall the gun feels really high quality for the price.
Even comes with a nice soft shell case.
Available in both .22 and .177 caliber pellet versions.
Cons:
Grips may be a bit too wide for smaller handed shooters.
Allen key does not fight the trigger adjustment.
Made in China.
Will need a pump or way to pressurize.
Comments:
For the price I don’t think you will find anything out there in terms of a PCP target pellet pistols with as many features as the Diana Bandit PCP .177 Caliber Bolt Action Pellet Pistol. At least in the lower cost price point Diana is offering it at. For that reason it is not going to be the absolute best all around PCP pellet firing target pistol you can get but I am sure bang for your buck you will be happy with this one. Everything about the Diana Bandit PCP .177 Caliber Bolt Action Pellet Pistol feels good quality, I would expect to pay at least double the price for something similar for sure. I have a feeling keeping the Diana Bandit PCP .177 Caliber Bolt Action Pellet Pistol in stock is going to be a challenge for us so if you see it in stock don’t take too long making up your mind or you may be in for a bit of a wait.
My Vimeo Table Top Review for the Diana Bandit PCP .177 Caliber Bolt Action Pellet Pistol:
In this Field Test Shooting Video I shoot the Cybergun FN Herstal FNX-45 Tactical GBB Airsoft Pistol in my indoor Sea Can Airgun Shooting Range to see what the real world velocity is and also how well it will group shooting 10 rounds at a paper target 30 feet down range. I was using .25 gram Airsoft BB’s for my testing along with Propane Gas. The temperature inside the sea can was around 26 degrees Celsius (79 degrees Fahrenheit).
Because the Cybergun FN Herstal FNX-45 Tactical GBB Airsoft Pistol coms with both a shorter internal barrel and a screw on extended barrel designed to be hidden inside a mock suppressor I thought it would make sense to test both the short and long barrels to see what the fps difference would be. With the short internal barrel I shot 4 rounds and average 255 fps. I then added the longer barrel extension again shooting 4 rounds but this time I averaged 363 fps so a good 100+ fps faster with the longer barrel attachment added to the Cybergun FN Herstal FNX-45 Tactical GBB Airsoft Pistol.
For my accuracy portion of the testing I left the extended barrel on the gun but was a bit disappointed in my 10 shot grouping. The Cybergun FN Herstal FNX-45 Tactical GBB Airsoft Pistol did not get the tightest of groupings coming in at around 5 inches. It also shot a little bit to the right but vertically was fairly well centered. Perhaps changing up the barrels and lengths might make a difference?
I did really like the Cybergun FN Herstal FNX-45 Tactical GBB Airsoft Pistol, it has a really light trigger that is a bit hard to find the release point, the blowback action is crisp but not overly heavy. I’m pretty sure the Cybergun FN Herstal FNX-45 Tactical GBB Airsoft Pistol is a VFC product so the quality is bang on. Other than the grouping being a little bit spread out I really liked everything about the Cybergun FN Herstal FNX-45 Tactical GBB Airsoft Pistol.
