Trigger Pull: The trigger pull on the KJWorks KP01-E2 Sig Sauer P226 Airsoft Replica is good in both single and double action. Once the slide is pulled back and released the first round is chambered and the hammer will remain back placing the KJWorks P226 in single action mode, the pull is light and the take-up is nice and short, most of your shots will be in single action mode unless you use the de-cocker to lower the hammer for a subsequent double action follow-up shot, double action shots are still pretty light but much longer in order to cock the hammer back.
Accuracy: (I have not shot the KJWorks distributed CO2 Mag version but I have already done a Field Test Shootinng Review for the same KJWORKS gun distributed and licensed by Cybergun in the Gas Mag version. Here is what I had to say about the Cybergun Gas Magazine version: "Shooting the Cybergun Sig P226 from 20 feet out in semi rested position I was able to get very good results. I placed 10 rounds in about 1.5 inches with the shot placement being a bit low possibly due to my barrel mod, adjusting the hop-up may bring the aim point back up to where it should be. The Sig Sauer P226 Airsoft Replica shot right around the 316 fps range while conducting my 5 shot average chrony testing which was lower than advertised but I was using much heavier .20 gram BB's. You can expect to get a full magazine worth of shots out of each gas fill-up but I did notice that as the magazine got colder it did tend to become much less efficient and also seemed to vent a lot of vapor."
Build Quality: The build quality for all KJWorks guns in my opinion is one of the best in the business. Fit and finish is top notch with close tolerances in the working parts as you would find in a real steel gun. The paint is excellent and in general will wear much better than other Airsoft guns out there. The KJWorks KP01-E2 (Sig Sauer P226) CO2 Blowback Airsoft Pistol is pretty much all metal and feels it, the recoil spring is nice and firm and all working parts are smooth and crisp when operated.
Realism: The KJWorks KP01-E2 (Sig Sauer P226) CO2 Blowback Airsoft Pistol is a replica of the real steel Sig Sauer P226 with the exception of the licensing. The KJWorks KP01-E2 really is a great looking and functioning Airsoft Replica. You can field strip this gun exactly like a real Sig Sauer and all the mechanical parts work just the same including a working de-cocker and adjustable front sight. It is really hard to distinguish the Airsoft version from the real Sig P226 in both looks and feel.
All metal pistol with good overall realistic weight to it.
Very crisp and firm full blowback operation.
Some of the best fit and finish in the industry. Especially in price range.
Nice accurate looking and working Sig Sauer P226 Replica.
Working de-cocker.
White dot sights for quick target acquisition.
Front sight is adjustable for windage.
Full size drop out magazine holds Airsoft BB's and CO2.
Fully field strip-able.
Cons:
No actual Sig Sauer Licensing but very clean look.
CO2 Mag does stick out a bit and add to size
Comments:
I am a huge Sig Sauer fan so I have kind of high expectations with a replica gun! The KJWorks lineup as a whole is really fantastic, and what I say about the KJWorks KP01-E2 (Sig Sauer P226) CO2 Blowback Airsoft Pistol can be said about the entire lineup. KJWorks makes a super well built product that replicates the real steal version almost exactly other then they shoot Airsoft BB's instead of actual bullets. When holding a KJWorks gun in the hand you can feel the quality, in weight, ballence and especially when operating the slide, trigger and other working parts. Everything just feels so perfect and responsive. For the money you can not go wrong with the KJWorks KP01-E2 (Sig Sauer P226) CO2 Blowback Airsoft Pistol or any other KJWorks gun for that matter.
My Vimeo Table Top Review of the KJWorks KP01-E2 (Sig Sauer P226) CO2 Blowback Airsoft Pistol:
Ammunition Capacity: 19 round metal stick drop out universal magazine.
FPS: 394 fps 120 m/s.
Trigger Pull: The trigger pull on the Gletcher BRT 84 is rather long and a bit on the heavy side but it is smooth and predictable. The release point takes a while to get to but once you figure it out you can get really accurate shot placement with this Beretta Model 84 replica. As with many low cost simplicity designed CO2 Air Pistols, the Gletcher BRT 84 uses the barrel like a hammer. When you pull the trigger, the inner barrel moves forward and out of the outer barrel allowing a BB to move into the breach area, then the barrel snaps rearward hitting the CO2 valve releasing CO2 and shooting the BB.
Accuracy: I tested the Gletcher BRT 84 All Metal CO2 BB Pistol from 30 feet back shooting at a paper target using a semi rested position I was able to get a near 1 inch 10 shot grouping on two separate occasions with this rather small and unassuming airgun. In terms of feet per second performance the Gletcher BRT 84 All Metal CO2 BB Pistol is rated at 394 fps, my Chronograph results shooting 5 rounds through the Chrony using a full CO2 and 5.1 grain Steel BB's was a respectable 421 fps, even a bit higher then the factor claim of 394.
Build Quality: Being a pretty much all metal gun, makes the Gletcher BRT 84 All Metal CO2 BB Pistol feel solid and sturdy even for such a small pistol. The only plastic parts on the Gletcher BRT 84 are the grips, the CO2 tab and perhaps an internal part like seals and such. The painted finish is a nice dark grey and seems to be wearing really well. Since the Gletcher BRT 84 All Metal CO2 BB Pistol is basically a one piece solid metal moulded airgun, there is really nothing to go wrong and no fit problems to speak of. Yes it is basic but it is also really well made.
Realism: The Gletcher BRT 84 All Metal CO2 BB Pistol is a replica of the real steel Beretta Model 84. It is an extremely close copy in terms of looks and feel, but does not have very many moving parts other than the trigger, magazine release and safety. So no slide movement or blowback, no working slide catch release, not even the hammer is functional. That said, not much to go wrong if what you are looking for is a gun that looks like a Beretta model 84.
Very solid all metal construction, good weight and feel.
Stick magazine is universal and can be used in many other guns.
Very accurate with good fps performance.
Grips feel nice, almost have a rubber like texture.
Simple design so not very much to go wrong with this airgun.
CO2 tab is hidden internally.
Reasonable price tag for well built all metal airgun.
Cons:
Very few working parts.
Trigger is a bit long and heavy, not ideal for action shooting.
Sights are non-adjustable
No Beretta Licensing
Comments:
I am usually not a huge fan of non-blowback basic airguns, especially when they do not have many working parts on them. However the Gletcher BRT 84 All Metal CO2 BB Pistol has some strong points that makes it worth considering, like it's solid all metal build, excellent accuracy and nice high fps performance for such a small sized airgun. It all feels really good in the hand ergonomically and based on the way it's built in such a simple no frills manner, the Gletcher BRT 84 All Metal CO2 BB Pistol should last a long time if taken care of.
Watch my Vimeo Review for the Gletcher BRT 84 All Metal CO2 BB Pistol:
Action: Semi auto non-blowback, double action only.
Ammunition Type: Airsoft plastic 6mm.
Magazine Capacity: 15 rounds
FPS: ? (1.6 Joules)
Trigger Pull: The trigger pull on the KWC Model 1911 All Metal Non-Blowback CO2 Airsoft Pistol was about medium to hard but I have definitely experienced heavier trigger pulls on many double action only Airguns. It is nice that the trigger has the look of a 1911 and not your typical lever styled trigger. I did find the trigger to be very usable and the release point is smooth and fairly predictable.
Accuracy: I have yet to perform my field test shooting component for the KWC Model 1911 All Metal Non-Blowback CO2 Airsoft Pistol, however I have reviewed the same gun in 4.5mm Steel BB Cybergun version and here is what I had to say about that the Steel BB version: "Accuracy was decent but not outstanding, I got around a 2.5 inch grouping from a 20 foot away free standing position, shooting just to the left and high on the target. I did find that I was able to zone in a bit better with the Cybergun GSR 1911 as I got used to the trigger. I also put the Cybergun Sig Sauer GSR through my Chrony Chronograph and got very close the manufacturers 397 claimed feet per second, actually starting off well above it and settling down to around the 370 FPS mark. My 8 shot average on a new CO2 was actually 422 FPS."
Build Quality: The build quality for the KWC Model 1911 is very good, this is an almost all metal Airsoft gun with a few exceptions like the hammer, trigger. magazine release, slide catch and grip safety. Pretty much everything else is metal including the slide, frame, magazine, and even the grips. The finish is very good and since there is lots of metal with minimal moving parts and less to go wrong, this should make for a very reliable pistol.
Realism: The KWC Model 1911 CO2 Airsoft Pistol is very close to the look, weight, and feel of the real steal Sig-Arms 1911 GSR! Even the 1911 style trigger was replicated as best as it could be given it being double action only. It would have been nice to have a single action trigger and a working slide to finish off the illusion but overall the GSR is a really nice copy of the real steel Sig Sauer GSR Sig-Arms 1911 firearm.
Very Accurate Sig-Arms Sig Sauer 1911 GSR Replica.
Should have good FPS and lots of shots per CO2 based on my 4.5mm BB version testing!
Very affordable and good value for the money.
Rail for mounting accessories.
Nice sights with white dots front and back.
Recessed barrel for added realism.
True 1911 style trigger even though it is double action only.
Very affordable price tag.
Cons:
Non-blowback and the slide does not move either.
The hammer is only for show and does not cock for single action shots.
Trigger action is bit heavy but not not too bad for a double action trigger.
Non adjustable rear sights.
Comments:
For a relatively inexpensive All Metal Airsoft gun you get a lot for your money with the KWC Model 1911, most importantly a very accurate reproduction of the real steal Sig-Arms Sig Sauer 1911 GSR firearm! If you're a 1911 fan and want to pick up an Airsoft gun that won't set you back too much, then the KWC Model 1911 would make a great choice with it's heavy full metal weight, full size drop out metal magazine, accurate reproduction of the real steal Sig-Arms GSR and again that very affordable price tag.
My Vimeo Videos for the KWC Model 1911 CO2 Airsoft Pistol:
This First Person Shooting Clay Pigeons Video with my KJWorks M9A1 and 1911 Airsoft Pistol is to serve two purposes: Number one and really the only reason needed to make a video like this... To get outside on a nice warm summer day and practice some tactile shooting all while recording it in first person so you can come along and enjoy it with me :)
Secondly I wanted to inform everyone that the video uploads will be a bit lighter for the next week or so since I am on what I call a working holiday. I am focusing on a Fitness Contest this weekend along with a Fitness Expo the following weekend, nothing to do with Replica Airguns but it does coincide with my other Website and YouTube channelGetFitOver40.com. The Fitness contest is the Victoria Cup where I will be competing in the Men's Physique (Masters - Over 40) and (Open - All Ages) divisions. The Fitness Expo is called "theFitExpo" and it is in Anaheim California.
So if you want to watch more of my videos then you will have to checkout my other fitness channel for the next week where I will be posting lots of related content on what's going on fitness wise in my life right now.
Trigger Pull: The trigger pull on the KJWorks Beretta M9 & M9A1 is very good in both single and double action. Double action is a bit longer and heavier than when shooting in single action but not heavy by any means. Single action shooting is short, light and crisp as you would expect when shooting a real steel Beretta 92 style pistol.
Accuracy: I have not done my actual Field Test Shooting video review for the KJWorks M9 and M9A1 Airsoft pistols but I did get the chance to make a short preview video where I shot both guns at some clay pigeons setup around 20 feet away. I was able to pop the center out of the clay pigeons no problem and found that even without any practice I was consistently hitting dead center on most shots. I am not sure exactly what the FPS will be but considering both theses versions of the KJWorks M9 & M9A1 have the CO2 mags they should shoot up into the 360+ fps range using .20 gram Airsoft BB's. Blowback operation is strong and the slides cycle full length. Keep posted for my upcoming Field Test Shooting Video for both pistols.
Build Quality: As expected, the KJWorks M9 & M9A1 build quality is just like all the other KJWorks Airsoft guns I've tested so far, excellent the fit and finish is the best in my opinion even when compared to my my 4.5mm steel BB shooters. When using these guns regularly, areas that are painted like the metal friction areas show very light wear which is rarely the case with metal built blowback Airguns. Again the tolerances between the moving parts like the slide and frame are very tight showing excellent workmanship and machining from KJWorks.
Realism: Both the KJWorks M9 & M9A1 are copies of the real steel popular Beretta M9 & M9A1, it is really hard to tell them apart from the real versions. Both the M9 and M9A1 are very similar in design with the M9A1 having some slight cosmetic differences, the biggest being the addition of a tactical rail built into the frame. Both KJWorks Beretta's can be field stripped in the same manor as a real Beretta M9 Semi Auto pistol and all parts function the same.
Pretty much all metal pistols with good weight to them.
Full heavy blowback operation.
Excellent fit and finish as always with KJWorks pistols.
High capacity full size drop out magazine that holds the Airsoft BB’s and CO2. (Can get Green Gas mags)
Seem to be very accuracy and well centered on target.
White dot sights make it easy to shoot an most backgrounds.
Ambidextrous safeties.
Field strip-able like the real steel versions.
Cons:
Sight are non-adjustable but elevation can be adjusted using the hop-up.
Grips may be a bit wide for some small handed people.
CO2 magazines sticks out a bit when using the CO2 mags.
Comments: The KJWorks Full Metal M9 & M9A1 are yet more examples of excellent full blowback Airsoft pistols from KJWorks. They are built to very high standards, are near perfect replicas of the real steel Beretta M9 & M9A1 and performance is also excellent. Yes the price is slightly higher than a similar Airsoft gun from KWC but the quality on the KJWorks is definitely worth the extra cost. Make sure to drop by our Replica Airguns Canada Store and checkout our new lower pricing on the KJWorks line of Airsoft guns.
My YouTube Table Top Review of the KJWorks M9and M9A1 Full Metal Blowback Airsoft Pistol:
Trigger Pull: The trigger pull on the KJWorks 1911 is very good since it is modeled after a real steel 1911 which makes it short and crisp with a very light trigger pull. There is a very slight take-up at the very beginning of the pull but once your get past this the release is crisp and perceptible. Since it is not a double action trigger you will need to either rack the slide for your first shot or pull the hammer back if you have already chambered a round.
Accuracy: I have not done my actual Field Test Shooting video review for the KJWorks 1911 Airsoft Pistol but I did get the chance to make a short preview video where I shot some clay pigeons setup around 20 feet away. The KJWorks Full Metal CO2 Airsoft 1911 was a lot of fun to shoot at the clay pigeons and I had no trouble hitting them form that range over and over again. I am not sure exactly what the FPS will be but considering this version of the KJWorks 1911 has the CO2 mag it should shoot up into the 360+ fps range using .20 gram Airsoft BB's. Blowback operation is strong and the slide cycles full length. Keep posted for my upcoming Field Test Shooting Video for the KJWorks Full Metal 1911 CO2 Airsoft Pistol.
Build Quality: As expected, the KJWorks 1911 build quality is just like all the other KJWorks Airsoft guns I've tested so far, excellent the fit and finish is the best in my opinion even when compared to any of my 4.5mm steel BB shooters or 6 mm Airsoft pistols. When using KJWorks guns regularly, areas that are painted like the metal friction areas and high spots show very light wear which is rarely the case with metal built blowback Airguns. Again the tolerances between the moving parts like the slide and frame are extremely tight showing excellent workmanship and machining from KJWorks.
Realism: The KJWorks CO2 Full Metal 1911 Blowback Airsoft Pistol copies the real steel very popular even today Colt 1911 A1, it is really hard to tell the KJWorks Airsoft 1911 apart from the real 45 caliber version. The KJWorks 1911 can be field stripped very similarly to a real 1911 Semi Auto pistol and all parts function virtually the same including a working safety, grip safety, slide catch-release, magazine release and hammer.
Pretty much all metal pistol with good realistic weight to it.
Full cycle heavy blowback operation.
Excellent fit and finish as always with KJWorks pistols.
High capacity 28 round full size drop out magazine that holds the Airsoft BB’s and CO2. (Can get Green Gas mags)
Seems to be accurate and well centered on target.
Nice two tone finish.
Working grip safety.
Nice light true single action only trigger.
Field strip-able.
Cons:
Sights are non-adjustable but you can adjust elevation using the hop-up.
Field strips a little different than a real 1911.
CO2 magazine sticks out a bit but KJWorks makes Gas Mags also.
Comments:
I am a big fan of 1911 pistols and love getting my hands on pretty much any version weather it be a Real Steel 45 caliber 1911, a 4.5mm Steel BB version or 6mm Airsoft Pistol. As long as it has that true 1911 single action short light trigger to it. I love the way the slide cycles a bit slower than most semi auto pistols and this can be found in many Airgun and Airsoft version like this KJWorks 1911 making the shooting experience even more realistic. The fit, Finish and overall quality of the KJWorks 1911 over other brands is worth the slight additional costs so if you don't mind paying juts a tad bit more for that extra quality and you're looking for a CO2 1911 then you will not be disappointed with the KJWorks Full Metal CO2 Airsoft 1911.
My Vimeo Table Top Review of the KJWorks M9and M9A1 Full Metal Blowback Airsoft Pistol:
We recently received some new pistols from KJWorks, The CO2 versions in Full Metal of the Colt 1911, the Berretta M9 and the Berretta M9A1. All of these guns are really well made, the fit and finish is excellent. Definitely a very high quality Airsoft pistol and worth spending a little bit more to get this extra quality. We have even lowered the price on many of our new KJWorks guns to make them even more affordable so check them out in our Canada Replica Airguns Store!
So I made a quick demo preview video where I get away from my table top and go outside to show them off a bit and shoot a few rounds through them at some clay pigeons. I did have some camera issues but you will get a good idea on how these guns look and perform.
Action: Semi auto non-blowback, double action only.
Ammunition Type: Airsoft Plastic 6mm BB's.
Ammunition Capacity: 15 rounds
FPS: 400+
Trigger Pull: The trigger pull on the KWC IWI Jericho 941 CO2 Airsoft Pistol is about medium to hard but defiantly not the worst airgun I have tested. After you quickly shoot off a full CO2 cartridge you may need a bit of a break to rest your trigger finger but the actual shooting experience is just fine and it does not effect accuracy too much once you get used to the pull and break point of the trigger.
"Accuracy was pretty good for a double action shooter, I got around a 1.5 inch grouping from a 20 foot away free standing position, shooting just a hair to the left but a bit on the high side. It is a bit unfortunately that the Jericho 941 does not have sight elevation adjustments as it would make a very accurate airgun otherwise. I also put the Cybergun IWI Jericho 941 through my Chrony Chronograph and got very impressive FPS results, actually starting off and staying well above the claimed manufacturers FPS. My 8 shot average on a new CO2 was a very high 488 FPS, again well above Cybergun's claimed 443 FPS."
Build Quality: Very good, the KWC Model 941 CO2 Airsoft Pistol weighs in at about 2 pounds which is a very hefty weight for a medium sized pistol. The build quality and fit and finish is good all around with decent usage of metal in the slide, magazine, outer barrel and trigger. There are not a lot of moving parts so I would expect good durability since there is not a lot to go wrong with this Airsoft pistol.
Realism: The KWC IWI Jericho 941 Airsoft Pistol is very close to the look, weight, and feel of the real Israel Weapons Industries Jericho 941! Even though it doesn't have a working slide it definitely looks the part with its cut out ejection port, full size drop out metal magazine and recessed metal barrel. The KWC Model 941 does not have any licensed trade marks to speak of but on the positive side of things it also doesn't have the ugly warning instructions written on it either.
All metal full size drop out magazine holds CO2 and Airsoft BB's.
Very accurate IWI Jericho 941 replica in terns of looks, size and weight.
Should get good FPS based on the steel BB version results.
Can expect lots of shots per CO2 based on Steel BB version.
Expecting good accuracy based on the steel BB version results.
Very affordable price at well under $100.
Cons:
Non-blowback and the slide is non-functioning.
The hammer is only for show and does not cock back for single action shots.
Non adjustable rear sights.
Trigger action is bit on the heavy side and gets a bit tiring after lots of shooting.
Comments:
For a relatively inexpensive Airsoft gun you get good value for your money, most importantly a very accurate reproduction of the real IWI Jericho 941 firearm in terms of size, looks and weight. I am hoping to get similar shooting results shooting the KWC Airsoft Model 941 as I did with my BB shooting Cybergun IWI Jericho 941 I tested a few yeas back as it was one of my highest fps BB pistols tested. So make sure to check back shortly for my Field Test Shooting Video Review for this Jericho 941 Airsoft version from KWC.
My Vimeo Videos for the KWC IWI Jericho 941 Airsoft Pistol:
Ammunition Capacity: 15 round full size drop out metal magazine.
FPS: 417.
Trigger Pull: The trigger pull on the ASG MK II is double action only which will make it a bit on the heavy and longer side when compared to a real steel Ruger MK II, it is smooth however and does have a nice satisfying click that sounds like a firing pin being release. The unfortunate part is that the real steel version is a single action only trigger and one that is super short and light so the contrast between the Airsoft and 22LR version may make this gun not practical is an optional training tool if you win the 22LR version also.
Accuracy: This part of the review is yet to be determined as I have not done my Field Test or Shooting tests for this pistol. I will put a link in here when I have done my official Field Shooting Test. For now all I can go on is some feedback from others that have claimed very high fps and excellent accuracy, I am looking forward to finding out for myself! You can watch my Ruger MK I Gas version Field Test Shooting Review to get an idea on how the ASG Ruger MK II version might perform.
Build Quality: ASG as usually distributes quality guns, the fit and finish on the ASG Ruger MK II Dual Tone CO2 6mm Airsoft Pistol is very good and there is use of metal where it needs to be like with the internal mechanical parts, the trigger, the safety, the rear fully adjustable sight and the full size drop out metal magazine that holds the CO2 and the Airsoft BB's. Thee MK II version has a metal upper which adds additional weight over the MK 1's plastic upper.
Realism: The ASG MK II is based on real steel Ruger MK II with the fluted barrel in a two-tone finish and looks very close to a real Ruger MK II. There is no blowback operation or bolt operation so that means that only a double action trigger is possible, this is a bit unfortunate since the real Ruger Mark II has an absolutely smooth and light single action trigger. On the positive side you can field strip the ASG Ruger MK II Dual Tone CO2 6mm Airsoft Pistol just like the real version.
If you own a real Ruger 22LR it would be nice to have for some backyard or basement shooting.
Adjustable rear sight for windage.
Adjustable Hop-up for Elevation.
Full size all metal drop out magazine that holds the CO2 and Airsoft BB's.
Metal upper barrel, Metal trigger, metal safety and many metal internals.
Very satisfying trigger sound, sounds like a real firing pin :)
Field Strips just like the real steel Ruger MK Series.
Cons:
Plastic sights front and back, plastic trigger.
No blowback (Would have allowed for a true single action trigger)
Double Action Only, unlike the real steel version that is single action only.
Comments:
Compared to the my previous review of the ASG Ruger MK I, the MK II for me is a big improvement. The metal upper barrel assembly makes all the difference in terms of weight and feel and with the two-tone look it is for sure a very attractive looking pistol. I also prefer using CO2 for the increased performance of higher fps and less cool down effect over a gas system. I am hopping my Field test Shooting video goes well and the ASG Ruger MK II Dual Tone CO2 6mm Airsoft Pistol performs on point for me.
My Vimeo Table Top Video Review for this ASG Ruger MK II Airsoft Pistol:
Ammunition Capacity: 20 round metal stick magazine.
FPS: 400 fps claimed.
Trigger Pull: Trigger pull on the Umarex HK 45 Metal Slide CO2 BB Pistol is double action only but doesn't feel too bad, it has the traditional longer double action pull but I did not find it to be too heavy and the release point was fairly predictable for me allowing for some good overall accuracy.
Accuracy: I have already done a full Felid Test Shooting Review Video for the Umarex HK 45 Metal Slide CO2 BB Pistol so make sure to check that one out! In summary I got a bit higher fps then claimed at 420 fps with a 5 shot string using a brand new CO2 with RWS 5.1 grain zinc coated steel BB's. From 30 feet away shooting on a paper target using a semi rested posting I was able to place 10 BB's within 1.5 inches, almost close to a 1 inch grouping. The shot placement for me was just a tad to the left and a bit down but several shots hit the bulls eye so out of the box accuracy was really good on this low cost BB pistol.
Build Quality: The Umarex HK 45 Metal Slide CO2 BB Pistol is built fairly basic with few moving parts so there is not much to go wrong, the fit and finish is good and there is metal where it needs to be internally and also the trigger, magazine and slide.
Realism: The Umarex HK 45 Metal Slide CO2 BB Pistol is a very good overall HK 45 Replica BB pistol in terms of size and looks, it has full HK licensing and even has a metal slide and polymer frame like the original real steel HK 45. It is a bit lighter bit not by too much. There is no working slide and the slide catch/release and hammer are molded into the gun. The only working parts would be the safety, magazine release and trigger.
Metal where it matters, slide, magazine, trigger, internals.
Nice replica of the original HK 45.
Fully HK Licensed.
White dot sights easy to sight in your target on most backgrounds.
Decent double action trigger.
Picatinny rail for accessories.
Cons:
None blowback with a fixed slide.
Slide catch/release and hammer are moulded in and none functioning.
Sights are none adjustable.
Comments:
For a rather low cost CO2 4.5mm steel BB pistol, the Umarex HK 45 has a lot going for it! It is fully HK Licensed with a metal slide and metal parts where you want and need it. The accuracy and power are both good and even the double action trigger is very usable. Sure the Umarex HK 45 Metal Slide CO2 BB Pistol is a pretty basic gun with few moving parts but then again simple is sometimes better in terms of reliability. If you are an HK fan and want a low cost well made and good performing BB pistol then checkout the Umarex HK 45.
My Vimeo Table Top Review for the Umarex HK 45 Metal Slide CO2 BB Pistol:
Trigger Pull: Trigger pull on the Webley MK VI .455 CO2 Shell Loading BB Revolver is great in both single and double action, for a shell loading revolver the double action is the best I have come across with next to no friction like I would usually find with shell loading revolvers when shot in double action mode.
Accuracy: I tested the Webley MK VI .455 CO2 Shell Loading BB Revolver on my pool deck first off shooting 6 rounds through my Chronograph. The claimed fps is 427, I got really close to 400 fps in my testing so there is the potential for this revolver to shoot up into the low 400's. When I stepped back 30 feet and shot 6 rounds form my semi rested position, I got a really tight 1 inch group with almost all the rounds landing in the bulls eye. My shots where just a hair to the right but not by much which is good since the sights on this pistol are none adjustable. You can check-out my full Field Test Shooting Video here!
Build Quality: The Webley MK VI .455 CO2 Shell Loading BB Revolver is pretty much an all metal construction other than the plastic grips and any internal seals. The fit and finish is excellent with a great overall weight in the hand. The only complaint I have is that the grips being a thin plastic seem kind of low quality compared to the rest of this otherwise high quality Webley CO2 BB Revolver.
Realism: In terms of replicating a real steel Webley MK VI .455, Webley did a really great job with their CO2 BB firing version. Webley even includes a Small Arms Training Manual based off of the real steel variant. Webley based the BB CO2 MK VI from the original blueprints and the licensing is form the original 1915 version. The only real tell that this is a CO2 BB revolver would be the small safety switch on the lower right side frame and the CO2 valve located right behind the hammer.
Looks amazing and is a very accurate replica of the real steel Webley MK VI.
Great weight and feel in the hand at 2.4 pounds
nice deep Recessed barrel with true .455 caliber opening.
Break barrel design makes it really easy to load the dummy shells.
Hammer / trigger action is great in single and double action.
Webley Licensed.
Well concealed CO2.
Fairly discreet safety location.
No ugly warning instructions on the gun!
Cons:
One of the higher cost shell loading revolvers we sell.
Sights are none adjustable.
Real version would shoot .455 caliber rounds, the dummy shells are actually closer to 357.
Could be a bit loud for some back yard shooters?
Plastic grips seem a bit cheap compared to the rest of this high quality gun.
Comments:
Another classic shell loading CO2 BB Revolver, nothing wrong with that, I remember a time when finding a realistic revolver, even a modern version was hard to do. Now we have a growing selection of super realistic revolvers that replica their original real steel variation with ultra realism. The Webley MK VI .455 CO2 Shell Loading CO2 BB Revolver is no exception and makes for yet another option if you want a well designed, super functional and ultra realistic classic BB revolver.
My Vimeo Table Top Review for the Webley MK VI .455 CO2 Shell Loading CO2 BB Revolver :
In part one test of the Umarex Polymer Colt Python 357 CO2 BB Revolver, the Chronograph velocity test I managed to get 5 reading out of 10 shots (Chrony was acting up again) and averaged 426 fps using 5.1 grain zinc coated RWS BB's with a brand new 12 gram CO2. Perhaps my average would have been slightly higher if I got all 5 readings on the first 5 shots since the fps is always a bit higher. My highest reading was 442 fps while my lowest reading near the end was 406 fps.
Part two, the accuracy component to this Shooting Field Test gave my fairly good results but perhaps not as good as the all Metal Shell Loading Umarex Colt Python I tested out earlier. I did find the Umarex Polymer Colt Python 357 CO2 BB Revolver shot well centered but got about a 2 inch grouping shooting 10 rounds on the paper target. If you find yours is not set to shoot exactly on the bulls eye you can easily adjust the sights for windage and elevation.
If you are wanting a higher than 6 round CO2 BB Revolver with a low price tag, good velocity, easy loading, adjustable sights, a smooth single and double action trigger and decent accuracy than checkout the Umarex Polymer Colt Python 357 CO2 BB Revolver!
In this Field test Shooting Review I again get out from under my deck roofing and take my Chronograph and target shooting onto the pool patio. I may as well take advantage of the great summer weather we are having and get some rays while I shoot a video :)
The CO2 BB Pistol I chose for this Field Test Shooting video is the Umarex HK45 Metal Slide CO2 BB Pistol. As per my usual Field Test Shooting Video Reviews, I test out the real world velocity (fps) for the Umarex HK45 BB Pistol by shooting 5 rounds through my Chronograph using a brand new CO2 and using 5.1 grain RWS zinc coated Steel BB's. I did have a few Chronograph issues but managed to get 5 good readings giving me an average of 421 fps.
Then I stepped back 30 feet and shot 10 RWS 5.1 grain zinc coated Steel BB's on a paper target to see how accurate the Umarex HK45 Metal Slide CO2 BB Pistol would be for me on this day. I was impressed to see a tight 1 inch grouping shooting from my rested position. The BB's where well centered on the target, just a hair to the left but good considering the sights are none adjustable.
Overall the velocity and accuracy of the Umarex HK45 are really good for this low cost BB pistol, the double action trigger is a bit long and on the medium pull, side but that is to be expected. The white dot sights make acquiring just about any target easy which may have helped me in my accuracy portion of the test.
In this Field test Shooting Review I get out from under my deck roofing and take my Chronograph and target shooting onto the pool area. Why not? The weather has been great and the pool is officially open and looking good :)
My pistol of choice for the Field Test Shooting video is the Gletcher BRT 84 All Metal CO2 BB Pistol. As per my usual Field Test Shooting Video Reviews, I test out the real world velocity for the Gletcher BRT 84 BB Pistol by shooting 5 rounds through my Chronograph using a brand new CO2 and 5.1 grain RWS zinc coated Steel BB's. I did have a few Chronograph issues but got a solid 4 readings giving me an average of 421 fps.
I then stepped back 30 feet and shot 10 of the same RWS Steel BB's on a paper target to see what kind of accuracy I could get shooting the Gletcher BRT 84 All Metal CO2 BB Pistol. I was impressed to see a close to 1 inch grouping shooting from a rested position. I actually performed this test twice because the first time I forgot to record with my camera glasses but I still got similar results both times.
The Gletcher BRT 84 All Metal CO2 BB Pistol is a bit on the louder side with a nice cracking sound when fired. The double action trigger is decent, nice and predictable but a bit on the long and heavy side since it is double action only. The sights are none adjustable but the Gletcher BRT 84 CO2 BB Pistol shot pretty true to the center of the target, juts a bit low and to the right but not by much. Overall for under $100 and being all metal this is a nice replica Beretta 84 BB shooter with good pereormcane.
In this Field Test Shooting Review I put the Webley MKVI .455 CO2 Shell Loading BB Revolver through my Chronograph and Target Tests to see how powerful and accurate the Webley MKVI really is!
Starting off with the the velocity Chronograph test, I shot 6 rounds through my Chrony using a brand new CO2 and RWS 5.1 grain zinc coated steel BB's in my Webley MKVI .455. My 6 shot string averaged just under 400 fps right at 397. Pretty decent for a shell loading BB revolver, not to mention very consistent shot to shot!
Next up was the accuracy component for this Field Test and as per usual, I setup my sand bag 30 feet away from my paper target and unloaded a full 6 round cylinder in to my ammo trap. I use a semi rested position, standing in the back resting my hands on a sand bag up front. This has proven to be a fairly stable shooting platform for me but there is some human factor involved. I was impressed with my 1.5 inch 6 shot grouping (right in the bulls eye) that could as easily been a 1 inch group if the one flyer had stayed a bit tighter but still really good performance for a none rifled BB shooter!
The hammer and trigger on the Webley MKVI .455 CO2 Shell Loading BB Revolver are very smooth in both single and double action with single action shooting being the shortest and lightest for best accuracy. It is still nice that this old school revolver offers double action shooting when you want to unload on your target quickly.
I also like the top break loading design which makes loading fast and easy on this 2.4 pounds all metal CO2 BB Revolver.
I wanted to not only do my Field Test Shooting review for the Umarex 9XP Blowback CO2 BB Pistol but also compare it to the discontinued Umarex SA177 since both guns share most of their internal parts. I had a good idea that both airguns would perform very similarly with perhaps the newer 9XP having the edge due to it being almost 5 years newer.
A with all my current BB Pistol Field Test Shooting Reviews, I test out the real world Feet Per Second performance by shooting 5 rounds through my Chronograph to see what they average out at, of course I use a brand new CO2 for this and my choice of BB was RWS Zinc coated 5.1 grain Steel BB's.
I started out testing the Umarex SA177 to use as my baseline and after about 5 warmup shots, the SA177 came back to life after sitting on the shelf for many years un-shot. My 5 shot string averaged a respectable 397 fps which is pretty good for a blowback pistol!
I then moved on to the newer Umarex 9XP CO2 Blowback Pistol and right away it popped out all 5 shots at over 400 fps with an average of 412 for my 5 shot string. Not only was the Umarex 9XP more powerful but it also had a snappier blowback action and was louder than the SA177 leading me to believe the CO2 valve may be setup to let out a bit more CO2 with each shot.
Stepping back 30 feet from my paper target I proceeded to again first test out the Umarex SA177 for the accuracy portion of this field test. I used my standard semi rested shooting stance, (sand bag up front, standing in the back) since it offers me a pretty stable shooting platform. I generally like to shoot 10 rounds into the paper target but the SA177 for some reason was having some slide lock back issues and I lost a BB in the process. Later on when I reloaded my SA177 I did not have this same problem so I am not sure what was going on. Even though the slide was locking back on some shots it did not really seem to effect the accuracy all that much. I got a main grouping that was about 1.5 inches in diameter and then a couple shots went out of that group extending the diameter to about 2.5 to 3 inches. Still pretty good for a blowback pistol. The shots where fairly well centered on the target.
When I performed the same test using my Umarex 9XP, I did not have any slide lock back issues and was able to get all 10 shot on target although one mystery shot did not seem to make a hole at all even though I clearly heard it fire and hit the target, perhaps it went exactly through an already existing hole? Either way I had a nice 5-6 shot group dead center on the target well under a 1 inch diameter and then 4 shots came outside extending the grouping to about 2 inches, again another well centered grouping!
In conclusion the Umarex 9XP Blowback CO2 BB Pistol is a nice replacement for the SA177, it performs very similarly to the SA177, even perhaps a bit better! To me it felt like the trigger on the Umarex 9XP was a bit heavier than the SA177 but not by much? Maybe the 9XP hammer spring is heavier which would explain the increase in fps. SO if you have been wanting an SA177 but can not find one used, grab yourself one of the Umarex 9XP's, you will not be disappointed :)
My main goal in this Shooting Performance Test was to see how the ANT Advanced Novelty Tech CO2 HPAConversion Kit performed side by side with a standard 12 gram CO2. Keep in mind that you can also switch over at any time to a regular 12 gram CO2 even after installing the ANT adaptor system in the gun or magazine.
My choice of Airgun for this test was the KWC - Cybergun Mini UZIConverted to Full Auto. I chose this Blowback 4.5mm CO2 BB Gun because it uses a lot of CO2 with each shot and when shooting in full auto it literally eats CO2. I knew this airguns would really put the ANT Advanced Novelty Tech CO2 HPA Conversion Kit to the test.
My first performance test was to comparing both systems using a Chronograph so I could see how the fps velocity slowed down because of the CO2 cool down effect. The 12 gram CO2 did pretty well emptying a full 25 round magazine but keep in mind I was shooting in semi auto only for the sake of using a Chronograph. I did notice a drop in velocity from a high of over 300 fps to a low of around 260. When I switched over to the Bulk CO2 ANT System and performed the same test the fps started out a bit lower but stayed pretty much about the same with a few ups and downs. The initial lower fps may have been a result of using separate magazines for each test since the valves in each magazine are most likely tuned a bit differently to let out more or less CO2 with each shot.
My second and most impressive test was to empty a full 25 round magazine in full auto mode! Again a started out using the standard 12 gram CO2 and to make this a real world test, I did not replace the 12 gram CO2 form the previous test. I figured 50 shots was a realist amount of shots to get from a single 12 gram CO2 and after all I was only shooting in semi auto which uses a lot less CO2 then shooting in full auto.
My KWC Blowback Mini UZI rocked pretty good using the 12 gram CO2 until it hit about a third the way through the magazine and then it stated to slow down and pretty much stop dead in its tracks with about 5-6 rounds still left in the magazine. The CO2 was all gone and I was left a bit unsatisfied :(
Without any significant break time to let my KWC Mini UZI warm up again, I switched over to the ANT Advanced Novelty Tech CO2 HPA Conversion Kit magazine and unloaded the full magazine in no time with no cycle rate slow down at all, even after the magazine was deprived of Steel BB's I kept squeezing the trigger and letting the blowback hammer my shoulder for several more satisfying bursts. Now that is what you expect from a full auto Blowback BB Machine gun!
In conclusion, when shooting in semi auto you will see better fps consistency using the ANT Advanced Novelty Tech CO2 HPA Conversion Kit but where this system really shines at least for me is I can shoot as fast as as long as I want and it will feel same as the very first shoot I take even when using a full auto system. No more switching out 12 gram CO2 every few magazines, just speed load some more BB's in and your good to go.
I was sent a really cool new product form a company called ANT (Advanced Novelty Tech). Their CO2/HPA Converter allows you to hook up either a large CO2 tank or High Pressure Air system using standard Paintball hose system.
What's kind of neat with the Advanced Novelty Tech CO2 HPA Conversion Kit, is that you can still interchange your 12 gram CO2 if you want to even after modifying your gun to use Bulk CO2 or HPA!
The ANT Advanced Novelty Tech CO2 HPA Conversion Kit works with well over 100 BB, Pellet and Airsoft guns most of which would be Pistols but some rifles are included in this list.
The main advantages over using standard 12 gram CO2 cartridges would be a significant lower cost for CO2, along with less fps velocity fall off, so better performance overall.
Stay posted as I will be making a field test performance test using the ANT Advanced Novelty Tech CO2 HPA Conversion Kit with my KWC Mini UZI Full Auto BB Machine gun :)
A few years back the Umarex SA177 disappeared off the face of the earth, well not really, it simply juts stopped being made and fairly quickly retailers ran out of stock... As with anything that people want but can not get any more, the demand went up and all of a sudden everyone seemed to want to get their hand on an Umarex SA177 Blowback BB Pistol.
You might ask why Umarex stopped making what at the time was a fairly popular CO2 BB Pistol? Well if you know anything about Glock, they do not like it all that much when a company makes a product that they feel infringes upon their intellectual properties and copy writes. Did the SA177 look like a Glock, well sure it had some similarities and perhaps Glock felt it was a bit too similar and so may have kindly asked Umarex to stop making it? At least that's what I think happened :)
So that brings us to now. And a new gun on the market called the Umarex 9XP that in many ways is a lot like the SA177 but with a slightly new skin on it, one that differentiates itself a bit more from the traditional Glock look. Sure the Umarex 9XP Blowback BB Pistol has a some Glock looking properties but it am guessing it has enough subtle changes to make the lawyers over at Glock HQ happy enough to allow Umarex to again sell an airgun very similar to the SA177.
Internally and mechanically as far as I can tell the Umarex SA177 and Umarex 9XP are the same and so they should both perform very similarly too each other and with pretty much all the same specifications. Even the magazines seem to be interchangeable! The trigger and trigger pull look to be identical and even the slide catch release are modeled after each other. Again, the only difference are some minor cosmetic changes to the metal slide and polymer frame.
So if you have been looking to get your hands on an SA177, well the next best or perhaps even better airgun is now available in the new Umarex 9XP! And the price is all right too!
Trigger Pull: Trigger pull on the Umarex Colt Single Action Army Shell Loading BB Revolvers is the best I have ever come across in an airgun. Being that the Umarex Single Action Army Revolvers are single action only, most of the work is done while you pre-cock the hammer. The trigger pull is under 2 pounds and has virtually no take up with a crisp release.
Accuracy: I tested both 4.5mm steel BB's and 4.7mm Lead ball BB's in the Umarex Colt Single Action Army Shell Loading BB Revolver. With the Steel 4.5mm BB's I shot just under a 2 inch 6 shot grouping when shooting from a 30 foot distance using a semi rested position (Sand bag up front, standing in the back). The shots where pretty well center hitting the paper target just a little bit high, they did seem to stray a little more left and right rather then up and down. When I switch ammo to the 4.7mm Lead BB's I got a similar 2 inch grouping but they hit the target a bit lower and tended to shoot tighter from side to side with more variation up and down, perhaps because the lead BB's did not seem to shoot at a vary consistent velocity. My Chronograph testing for the Steel BB's was right around 400 fps while the Lead BB's being heavier shot a bit slower at just under 300 fps.
Build Quality: The Umarex Colt Single Action Army Shell Loading BB Revolvers have a mostly all metal construction other than the plastic grips and any seals. The fit and finish is excellent with a great overall weight in the hand. Whether you get the Nickel or Blued version. The mechanical action of the hammer and trigger feels just like it would on a real single action army revolver.
Realism: In terms of replicating a real steel Colt Single Action Army Revolver, Umarex has done a really great job with their CO2 BB firing version. It's really hard to tell one from the other except for the smaller shells and the discreet safety switch located under the frame. Even the barrel is nicely recessed and has some fake rifling twists in it. The CO2 is well hidden with the Allen key built into the handle so no ugly screw tab hanging down.
Looks amazing and is a very accurate replica of the real steel old west version.
Recessed barrel with fake rifling.
Great weight and feel in the hand.
Shell loading design that loads from the back so no need to remove shells if you wish not to.
Hammer and trigger action is about perfect, no take-up, very crisp and super light.
Finish on both the Nickel and Blued version is very nice.
Very well concealed CO2 with built in Allen key.
Discreet safety location.
Cons:
In your face warning instruction on the right side of the barrel are a shame.
Real steel version would shoot .45 caliber bullets, dummy shells are actual closer to a .38.
Seems really quiet to shoot, would like to see a louder more powerful version!
Comments:
All I can say is we finally got our Airgun 1857 Colt Single Action Army Revolver! I have been asking the big airgun companies for this for a while and I knew it would be very popular once made available. As it turns out, not only do the "Americans" want one, but so do many folks overseas! I am really glad that time and effort was put into this first version and we got such a great product that looks amazing and shoots just as good as it looks. For anyone who is interested in owning the classic cowboy six shooter, you have to make sure to get one of these super realistic Single Action Historic Revolves!
My Vimeo Table Top Review for the Umarex Colt Single Action Army CO2 BB Revolver :
