In this Field Test Shooting Video I test out the Velocity and Accuracy of the Umarex VFC Heckler & Koch HK416C V2 AEG Airsoft Rifle by first placing 5 rounds through my Chronograph and recording the feet per second of each shot then averaging them out. For the second portion of my Indoor Shooting Performance Test I setup a paper target 30 feet away and then shoot 10 rounds back to back to see what the spread or grouping size is. I follow this up with a full auto burst just for fun to see if the grouping still remains nice and tight.
For my Velocity test I used .25 grain Plastic Airsoft BB’s rather than the .20 in the claimed fps over 366 fps so I was expecting to get a little bit slower results. I did manage to average right around 325.5 fps with all shots consistently hitting either 325 or 326 fps so super consistent.
I then setup my brand new paper target and using a rested and seated shooting position from 30 feet back I placed my first 10 rounds into the target. This is when I discovered the Umarex VFC Heckler & Koch HK416C V2 AEG Airsoft Rifle liked to shoot fairly low even when using the raised elevation option on the rear sight. Because of this I had to aim a little bit higher on the paper target to place shoots more centered. Once I figure out my aim point I did mange to get a fairly tight 10 round grouping of close to an inch with a couple of stagers pushing it out to 2 inches. Full auto was as predicted, lots of fun with a nice hole in the paper/cardboard leaving about a 3.5 inch opening.
The Umarex VFC Heckler & Koch HK416C V2 AEG Airsoft Rifle performed well for me once I figured out that it liked to shoot rather low. I would suggest placing a bit of a spacer or riser under the rear sight to bring up the barrel at least for closer in shots where hop-up may not ark the Airsoft BB enough at that point. Other than that the Umarex VFC Heckler & Koch HK416C V2 AEG Airsoft Rifle had super consistent performance in terms of both FPS and accuracy.
Type: AEG Airsoft Rifles Manufacturer:Umarex / VFC Model:HK416 V2 Materials: Fiberglass reenforced plastic and metal. Weight: 7 pounds (3180 grams). Total Length: 28 - 31.1 inches (710-790). Barrel: 10.2 inches (260mm) non rifled. Propulsion: AEG. Action: Single action semi & full auto. Ammunition Type: .6mm plastic Airsoft BB’s. Ammunition Capacity: High cap 320 round magazines. FPS: 366+ fps.
Trigger Pull: The trigger pull on the Umarex VFC Heckler & Koch HK416 V2 AEG Airsoft Rifle is similar to a light single action trigger as they are essentially an electrical on off switch. There is about a quarter inch of take up with virtually no extra friction to let you know when the release is going to be, with a bit of use you will figure out exactly when the trigger will release the action.
Accuracy: At this time I have not made my Field Test Shooting Video or even shot the Umarex VFC Heckler & Koch HK416 V2 AEG Airsoft Rifle, but plan to make my Field Test Shooting Video shortly. So stay posted for that video coming out soon. I do expected Umarex VFC Heckler & Koch HK416 V2 AEG Airsoft Rifle to perform well as it is a high quality and not so inexpensive AEG Airsoft Rifle.
Build Quality: The Build quality on the Umarex VFC Heckler & Koch HK416 V2 AEG Airsoft Rifle looks to be really good, there are lots of quality metal parts throughout this Airsoft Rifle including the top and bottom receiver, rails, parts of the sights, flash hider, magazine, charging handle, selector switch, magazine release, forward assist, dust cover, buffet tube and trigger. VFC (Vega Force Company) is the actual manufacturer of this product line and they are well know for making high quality Airsoft products.
Realism: The Umarex VFC Heckler & Koch HK416 V2 AEG Airsoft Rifle is a 1 to 1 scale fully licensed replica of the real steel HK 416 compact CQB styled rifles . You’ll find that most part work in the same manner as with the real steel version including the Charging Handle, Forward Assist, Bolt Release, Magazine Release, Selector Switch and Pop-up sights.
Pros:
Full H&K Licensed via Umarex.
Made by VFC (Vega Force Company), well known for quality products.
Lots of metal parts where would find them on the real steel HK416.
Semi auto & full auto selectable.
No orange tip on Canada import version.
Comes with AR type compatible high capacity 320 round magazine.
Removable metal sights are adjustable for windage.
Lots of rail attachment positions.
Easy access to hop-up system.
Quality internals - V2 metal gearbox and built in Mosfet.
Fully adjustable rear stock.
Cons:
Price is on the higher end.
No elevation adjustment on sights.
Comments:
The Umarex VFC H&K AEG Airsoft product line is going to be on the higher end of the price spectrum for sure but you are getting a really quality product here fully H&K licensed. The Umarex VFC Heckler & Koch HK416 V2 AEG Airsoft Rifle has a really nice form factor allowing for a full size rear adjustable stock which will make your shooting position a lot more comfortable while still allowing for a rather compact form factor overall. I look forward to seeing how well the Umarex VFC Heckler & Koch HK416C V2 AEG Airsoft Rifle performs in my upcoming Field Test Shooting Video.
My Vimeo Table Top Review for the Umarex VFC HK416 V2 AEG Airsoft Rifle:
Type: AEG Airsoft Rifles Manufacturer:Umarex / VFC Model:HK416C V2 Materials: Fiberglass reenforced plastic and metal. Weight: 6.1 pounds (2780 grams). Total Length: 22.6 - 27.4 inches (573-696mm). Barrel: 8.3 inches (210mm) non rifled. Propulsion: AEG. Action: Single action semi & full auto. Ammunition Type: .6mm plastic Airsoft BB’s. Ammunition Capacity: High cap 320 round magazines. FPS: 366+ fps.
Trigger Pull: The trigger pull on the Umarex VFC Heckler & Koch HK416C V2 AEG Airsoft Rifle is similar to a light single action trigger as they are essentially an electrical on off switch. There is about a quarter inch of take up with virtually no extra friction to let you know when the release is going to be, with a bit of use you will figure out exactly when the trigger will release the action.
Accuracy: At this time I have not made my Field Test Shooting Video or even shot the Umarex VFC Heckler & Koch HK416C V2 AEG Airsoft Rifle, but plan to make my Field Test Shooting Video shortly. So stay posted for that video coming out soon. I do expected Umarex VFC Heckler & Koch HK416C V2 AEG Airsoft Rifle to perform well as it is a high quality and not so inexpensive AEG Airsoft Rifle.
Build Quality: The Build quality on the Umarex VFC Heckler & Koch HK416C V2 AEG Airsoft Rifle looks to be really good, there are lots of quality metal parts throughout this Airsoft Rifle including the top and bottom receiver, rails, sights, flash hider, magazine, charging handle, selector switch, magazine release, forward assist, dust cover and trigger. VFC (Vega Force Company) is the actual manufacturer of this product line and they are well know for making high quality Airsoft products.
Realism: The Umarex VFC Heckler & Koch HK416C V2 AEG Airsoft Rifle is a 1 to 1 scale fully licensed replica of the real steel HK 416 compact CQB styled rifles but in an even more compact design I believe specifically only found in Airsoft versions as I was not able to find the exact same model on the H&K Website. That said most part work in the same manner as you would find on the real steel version including the Charging Handle, Forward Assist, Bolt Release, Magazine Release, Selector Switch and Pop-up sights.
Pros:
Full H&K Licensed via Umarex.
Made by VFC (Vega Force Company), well known for quality products.
Lots of metal parts where would find them on the real steel HK416.
Semi auto & full auto selectable.
No orange tip on Canada import version.
Comes with AR type compatible high capacity 320 round magazine.
Pop up metal sights are adjustable for windage.
Lots of rail attachment positions.
Easy access to hop-up system.
Quality internals - V2 metal gearbox and built in Mosfet.
Ultra compact adjustable CQB stock.
Cons:
Price is on the higher end.
No elevation adjustment on sights.
Limited to physical size/type of battery used.
Comments:
The Umarex VFC H&K AEG Airsoft product line is going to be on the higher end of the price spectrum for sure but you are getting a really quality product here fully H&K licensed. The Umarex VFC Heckler & Koch HK416C V2 AEG Airsoft Rifle is perhaps one of my favorites as I like more simplistic and minimalist styles of guns and this one for sure fits into that category. Even though it is small in nature it is super solid and heavier then it looks for sure when you pick it up with all the metal parts making up its build quality. I look forward to seeing how well the Umarex VFC Heckler & Koch HK416C V2 AEG Airsoft Rifle performs in my upcoming Field Test Shooting Video.
My Vimeo Table Top Review for the Umarex VFC HK416C V2 AEG Airsoft Rifle:
In this video I show you four Premium AEG Airsoft Rifles made by VFC and distributed and H&K Licensed by Umarex. This is not a detailed review but rather I focus on the basic specification and show my reaction as I take my first look at all four Umarex H&K AEG Airsoft Rifles. I do show off some close up photos so you can get an idea on the finish and what some of the components look like.
For this Field Test Shooting Video I put the Specna Arms RRA SA-C10 Core and Specna Arms RRA SA-E10 Edge head to head to see just how they will compare in terms of FPS and Accuracy at least out to 30 feet. If you want to know more about each of these AEG Specna Arms Airsoft Rifles then checkout my Table Top Review where I show them up nice and close and also talk about their specifications and how they both compare to each other.
For my Chronograph test, I decided to go with .25 gram Airsoft BB’s, a little bit heavier than what was used for the claimed FPS of around 380 using the M120 spring which by the way is preinstalled in these guns for import into Canada. Both the Specna Arms RRA SA-C10 Core and E10 Edge shot pretty similar with the C10 Core averaging right around 300 FPS and the E10 Edge shooting a little bit faster with 318 FPS. Throw some lighter .20 gram Airsoft BB’s into the mix and these numbers would go up for sure. I was using the same 11.1 volt Li-Po battery for all of my testing in this video.
Next I placed a fresh paper target 30 feet downrange and placed 10 semi auto rounds into it using a seated and rested shooting position. Both Specna Arms AEG Airsoft Rifles shot about a 1 inch grouping. I did find with both of these Specna Arms rifles that when using the peep sight they shot too low and when using the top notch sight they shot too high at least at this distance. Of course the sights are fully adjustable so this can easily be taken care of and you can adjust the hop-up for even more elevation considerations. After my 10 shot semi auto test I placed both Specna Arms Airsoft rifles in Full Auto and let the paper have it! As expected the groupings did spread out a little bit but not all that much, perhaps opening up to around 3-4 inches.
After testing both the Specna Arms RRA SA-C10 Core and E10 Edge AEG Airsoft Rifles side by side you really can’t go wrong with either version as they performed very similarly on the Chronograph and on Target. If you can afford to pay the little bit more than I would go with an Edge Series Specna Arms product since you do get a lot of extras for the little bit more you pay. Well worth it!
Type: AEG Airsoft Rifles Manufacturer:Specna Arms. Model: RRA SA-C10 / RRA SA-E10 Materials: Fiberglass reenforced plastic and metal/aluminum. Weight: C10 4.9 pounds ( 2.2 kg) - E10 5.1 pounds (2.3 kg). Total Length: 21.7 - 25.2 inches (550 - 640mm). Barrel: 6.7 inch (170mm) inner 6.03mm tight bore barrel non rifled. Propulsion: AEG. Action: Single action semi & full auto. Ammunition Type: .6mm plastic Airsoft BB’s. Ammunition Capacity: Mid cap 120 round magazines. FPS: 375 - 390 fps with installed spring, included M90 spring will be lower fps.
Trigger Pull: The trigger pull on both of the Specna Arms RRA SA-C10 Core and E10 Edge AEG Airsoft Rifles is similar to a light single action trigger as they are essentially an electrical on off switch. There is a little bit of take up with virtually no extra friction to let you know when the release is going to be, with a bit of use you will figure out exactly when the trigger will release the action.
Accuracy: At this time I have not made my Field Test Shooting Video or even shot the Specna Arms RRA SA-C10 Core and E10 Edge AEG Airsoft Rifles, but plan to very soon. They are next on my list for Filed Test Shooting Videos so stay posted for that video coming out soon. I do expect them to perform well and will be shooting both of these models side by side to see if there is any noticeable difference between the lower cost Core versus the slightly more premium Edge Specna Arms versions.
Build Quality: One thing I can say is no matter which version of the Specna Arms AEG Air Rifles you deicide to go with (either a Core or Edge Series), you are getting extremely good value for your money and neither one is going to have any low quality parts in it. Even the lower cost Core Series will have fiber glass reenforced plastic and metal parts along with a metal gearbox and virtually almost the same build as the more premium and slightly higher priced Edge Series. You will get upgrades in the Edge Series such as a an aluminum receiver and buffer tube, a GATE X-ASR Mosfet, the New Orion Gearbox, deep laser engraved licensing and an additional magazine. All of this for the little bit more you pay for an Edge series Specna Arms AEG Airsoft rifle.
Realism: The Specna Arms RRA SA-C10 Core and E10 Edge AEG Airsoft Rifles are based on the AR15 or M16 platform of course in a very modern and PDW styled look. They look and feel the part for sure with lots of working parts including the safety, selector switch, charging handle, dust cover, adjustable rear stock, pop-up front and rear sights as you would expect. Most of the hardware should be interchangeable with a real steel AR if you want to personalize the look of your Specna Arms Rifle.
Pros:
Super affordable yet very high quality product for what you pay.
Two options to consider, both with good price points and value.
Quality components throughout both the Core and Edge series.
Rock River Arms Licensed with hologram on receiver.
ESA™ quick spring change system makes spring changes quick and easy.
Comes with two springs for potential indoor and outdoor usage.
Plastic parts are fiberglass reenforced making them very durable.
Quick release fully adjustable pop-up sights.
No orange tips on our Canada Store versions.
Lots of rial mounting options even on such short PDW styled AR’s.
Metal gearboxes with metal gears and mostly all metal parts inside.
Easy access to motor for any possible trouble shooting you may need to do.
Cons:
Popup sights are mostly plastic..
Need to hold back charging handle to access the hop-up wheel.
Comments:
Value for your money is what comes to mind when I think about the entire Specna Ams AEG Airsoft Riffle product line. And this goes for not only the lower priced Core Series but also the premium Edge Series. Both version are built supper tuff with quality components throughout. You are just getting upgrades you are probably going to do at some point in time with the Edge Series and of course more metal components when you spend about $100 more for a similar Edge version. I figure if you can muster up the extra cash then go with an Edge Specna Arms AEG Airsoft Rifle, that said, any of the Core models will be money well spent.
Make sure not also watch my previous Specna Arms YouTube Video where I introduce the product line, show you around several models and talk about the key differences between the Core and Edge versions.
My Vimeo Table Top Review for the Specna Arms RRA C10 Core & E10 Edge Airsoft Rifles:
We have a new line of Airsoft rifles from Specna Arms I am super happy to be introducing to the Replica Airguns Airsoft Community.
Specna Arms AEG Airsoft Rifles are extremely cost effective and offer value for what you pay that is amazing. In this YouTube Introduction Video I go over the main differences between the Core Series (lower priced) versus the Edge Series (mid priced) so that you can understand what the extra cost will get you when buying a Spenca Arms Edge Series AEG Airsoft Rifle over a Specna Arm Core Series AEG Airsoft Rifle.
I also show 12 different versions from the Specna Arms Core and Edge Series some with Rock River Arms licensing and some without.
Specna Arms Core Series
Price: Mid $200’s (CAD)
Materials: Fiberglass Reenforced Plastic & Metal
Mosfet System: No
Gear Box: Ver 2 Metal Fully Upgradeable
Spring System: ESA Quick Change - 2 Springs (380-310 fps)
I have review all three of these super fun Full Auto CO2 BB Rifles so make sure to watch those YouTube Field Test Video Shooting Reviews to see how they performed on their own in the Sea Can Indoor Airgun Shooting Range.
In this Field Test Shooting Video I have a little bit of fun to see which of the three Full Auto CO2 BB Rifles is the King in terms of FPS Velocity and all out full auto mag dump acuracy.
All there of these BB Rifles are awesome and I highly recommend picking one up or maybe even all of them! You can get them in our Canada and US Replica Airgun Stores…
There is not much to really say here, it’s all about watching this one as I basically shoot stuff with the Air-Ordnance SMG 22 Full Auto Pellet Rifle and figure out how many 100 round belts I can get out of a fully charged 3000 PS 48 CU PCP Tank. So make sure to watch this one for sure!
There have been lots of requests for me to get to the Field Test Shooting Video for the Air-Ordnance SMG 22 Full Auto Pellet Rifle and I know I have been a it late getting this one out there. To be honest I was not looking forward to pumping up the rather large PCP tank and loading up all the 100 round magazines but it had to be done and so here we are…
In this Part 1 of my Air-Ordnance SMG 22 Full Auto Pellet Rifle Field Test Review I perform my usual Sea Can Indoor Shooting Test and place some rounds through my Chronograph to see what the actual FPS is. I also shoot a 10 round group at a paper target 30 feet down range to see what kind of accuracy we can expect from the Air-Ordnance SMG 22 Full Auto Pellet Rifle. By the way in Part 2 I take my Air-Ordnance SMG 22 Full Auto Pellet Rifle outside to have some fun with it and blast away in full auto so make sure to watch that video coming out very soon…
The Air-Ordnance SMG 22 Full Auto Pellet Rifle with a full PCP tank pressurized right up to the max 3000 psi and using 15.43 grain lead pellets was able to get an average fps of 422 which worked out to 6.1 foot pounds of energy or about 8.3 Joules. By the way I was able to get through 3 full 100 round magazines with a fully charged 48 CU Tank which is impressive. Shots did slow down a bit at the end but the gun was able to cycle fully.
In terms of accuracy my Air-Ordnance SMG 22 Full Auto Pellet Rifle was not the most accurate performer I have tested but considering it is a full auto Airgun and not so much made for total accuracy, the 3 inch 10 shot grouping I did get was good enough for me! Of course I was shooting in semi auto mode during this test which is pretty easy to do, no selector switch to worry about, just don’t hold the trigger down and you get semi auto shooting from the Air-Ordnance SMG 22 Full Auto Pellet Rifle, hold it down and you get full auto, and the tighter you hold the trigger down the faster the air machine-gun rate of fire operates.
So far so good, no miss-feeds or any problems with my Air-Ordnance SMG 22 Full Auto Pellet Rifle. now to take it outside and let loose on some clay pigeons, pop cans and a metal target.
Make sure to watch my Table Top Review for the Diana Bandit PCP .177 Caliber Bolt Action Pellet Pistol if you haven’t already done so to get all the specifications and features along with some nice close up video. In this Field Test Shooting video I test out the Diana Bandit PCP .177 Caliber Bolt Action Pellet Pistol to find out what the real world velocity is and also just how accurate it will be shooting a paper target from 30 feet back using a rested shooting position. Since the Diana Bandit PCP .177 Caliber Bolt Action Pellet Pistol is a target pistol I was hoping for good accuracy since the Diana Chaser performed so well for me in my earlier Field Test Shooting video this week. The Diana Bandit does have a claimed 700 fps velocity but I believe this is for the non-Canada detuned version so it will be interesting to find out exactly what the power is.
First up I placed 5 shots through my Chronograph with a fully charged PCP tank using 6.9 grain RWS lead pellets and got just over 500 fps results averaging 517 fps, so yes the Diana Bandit PCP .177 Caliber Bolt Action Pellet Pistol has been detuned to make it Canada non-regulated legal.
Next I performed my accuracy test shooting at a paper target 30 feet down range with the Diana Bandit PCP .177 Caliber Bolt Action Pellet Pistol rested on a sand bag up front and sitting in the back. Since the magazine holds 9 rounds I placed 9 round on the target to see what kind of grouping I could get. At first I was not sure why my 9 shot grouping seemed to be much more spread out than My Dianna Chaser results but after watching the video I saw that only one shot really came out of the 1 inch grouping not including the random accident shot I took. Perhaps I had a misinformed pellet or perhaps I pulled that one shot. That shot aside both the Diana Bandit and Chaser performed about the same, even shooting just a hair to the left from the bullseye.
The trigger feels pretty decent, not super light or to heavy, there is a little bit of take-up and then a slight resistance then a quick release. The bolt action along with the 9 round rotary magazine worked flawlessly for me with no jamming at all. For the low price this PCP Target Pellet Pistol comes in at you really can’t go wrong and if you want to modify or upgrade it down the road there are tons of things you can do to the Diana Bandit PCP .177 Caliber Bolt Action Pellet Pistol. I highly recommend the Diana Bandit PCP .177 Caliber Bolt Action Pellet Pistol if you are looking for a super affordable PCP target pellet pistol.
Make sure to watch my Table Top Review for the Diana Chaser CO2 .177 Caliber Bolt Action Pellet Pistol if you haven’t already to get all the specifications and features along with some nice close up video. In this Field Test Shooting video I test out the Diana Chaser CO2 .177 Caliber Bolt Action Pellet Pistol to find out what the real world velocity is and also just how accurate it will be shooting a paper target from 30 feet back using a rested shooting position. Since the Diana Chaser CO2 .177 Caliber Bolt Action Pellet Pistol is a target pistol I was hoping for good accuracy but based on the claimed 525 fps velocity I was also hoping for close to 500 fps results.
First up I placed 4 shots through my Chronograph using a brand new CO2 along with 6.9 grain RWS lead pellets and got pretty close to 500 fps results averaging 490 fps, not bad considering the temperature was not super warm and I was using led pellets not hyper velocity alloy pellets.
Next I performed my accuracy test shooting at a paper target 30 feet down range with the Diana Chaser CO2 .177 Caliber Bolt Action Pellet Pistol rested on a sand bag up front and sitting in the back. Since the magazine holds 9 rounds I placed 9 round on the target to see what kind of grouping I could get. I was impressed to see a nice 1 inch grouping, maybe even a little bit less removing the paper tearing. Shots where vertically right on the mark and just a tad to the left but easily fixable with a quick tweak of the full adjustable sights.
The trigger feels pretty decent, not super light or to heavy , there is a little bit of take up and then a slight resistance then a quick release. The bolt action along with the 9 round rotary magazine worked flawlessly for me with no jamming at all. For the low price this CO2 Target Pellet Pistol comes in at you really can’t go wrong and if you want to modify or upgrade it down the road there are tons of things you can do to the Diana Chaser CO2 .177 Caliber Bolt Action Pellet Pistol. I highly recommend the Diana Chaser CO2 .177 Caliber Bolt Action Pellet Pistol if you are looking for a super affordable target pellet pistol.
Type: Pellet Pistol Manufacturer:Diana. Model:Bandit Materials: Wood and Metal, some plastic. Weight: 2.2 pounds (1000 grams). Total Length: 20.1 inches (51 cm) Barrel: 9.5 inches (24 cm), metal rifled. Propulsion: PCP. Action: Bolt. Ammunition Type: .177 & .22 Caliber pellets. Ammunition Capacity: Single shot to 9 & 7 round magazines.. FPS: 725 (.177) - 630 (.22). Need to test for Canada import version
Trigger Pull: The trigger pull on Diana Bandit PCP .177 Caliber Bolt Action Pellet Pistol is single action only meaning in order to cock the internal hammer/striker, you need to cycle the bolt back and forth allowing for a short and light trigger action. It does come with a rotary multi-round magazine that allows for the cycling of the bolt to automatically advance a pellet allowing for much quicker followup shots.
Accuracy: At this point I have not personally tested the Diana Bandit PCP .177 Caliber Bolt Action Pellet Pistol in terms of actual power and accuracy but I expect the Diana Bandit PCP .177 Caliber Bolt Action Pellet Pistol to perform well since in fact this is a target pistol with fairly high claimed fps. In the next few weeks I plan on making my Field Test Shooting Video so stay posted for the results from that video for confirmation of the performance.
Build Quality: The Diana Bandit PCP .177 Caliber Bolt Action Pellet Pistol is made in China which might make you wonder about the overall quality of this target pistol but after taking a good look around and working all the mechanical parts I ma very impressed with the overall quality and chosen material that went into the production of the Diana Bandit PCP .177 Caliber Bolt Action Pellet Pistol. You will finds metal where you need it as in the barrel, bolt and trigger. The pistol grip are made of wood but you will find some portions of the sights are plastic but it would have been nice if they where all metal.
Realism: Realism isn’t really a concern with the Diana Bandit PCP .177 Caliber Bolt Action Pellet Pistol since it is not a Replica Airguns but in terms of looking like a gun it serves that purpose, no mistaken that so no waving it around in public or things may not turn out so good for you…
Pros:
Inexpensive fairly high quality full featured target pistol for the price.
Expect good accuracy!
Metal construction where it needs to be (Bolt, barrel, trigger).
Rifled barrel.
Fully adjustable sights.
Adjustable and light single action trigger.
Dove tail on bolt for adding optical sight.
Nice wood pistol grip.
Good for small pest control because of fairly high fps and expected good accuracy for shot placement ability.
Overall the gun feels really high quality for the price.
Even comes with a nice soft shell case.
Available in both .22 and .177 caliber pellet versions.
Cons:
Grips may be a bit too wide for smaller handed shooters.
Allen key does not fight the trigger adjustment.
Made in China.
Will need a pump or way to pressurize.
Comments:
For the price I don’t think you will find anything out there in terms of a PCP target pellet pistols with as many features as the Diana Bandit PCP .177 Caliber Bolt Action Pellet Pistol. At least in the lower cost price point Diana is offering it at. For that reason it is not going to be the absolute best all around PCP pellet firing target pistol you can get but I am sure bang for your buck you will be happy with this one. Everything about the Diana Bandit PCP .177 Caliber Bolt Action Pellet Pistol feels good quality, I would expect to pay at least double the price for something similar for sure. I have a feeling keeping the Diana Bandit PCP .177 Caliber Bolt Action Pellet Pistol in stock is going to be a challenge for us so if you see it in stock don’t take too long making up your mind or you may be in for a bit of a wait.
My Vimeo Table Top Review for the Diana Bandit PCP .177 Caliber Bolt Action Pellet Pistol:
Type: Airsoft Pistol. Manufacturer:KWC. Model: PT92 Materials: Almost entirely all Metal. Weight: 2.4 pounds (1089 grams). Barrel: 4.5 inches, metal non-rifled. Propulsion: 12 gram CO2. Action: Semi and full auto, single and double action with full blowback. Ammunition Type: 6mm Plastic Airsoft BB's. Ammunition Capacity: 27 rounds full size drop out metal magazine. FPS: 388 using .25 gram Airsoft BB’s.
Trigger Pull: The trigger pull on the KWC PT92 CO2 Blowback Airsoft Pistol is good in both single and double action. Of course in single action the trigger is much shorter and lighter but that said double action is still very usable. Once you fire a round in either double or single action the blowback action will continue to cock the hammer back allowing for single action followup shots.
Accuracy: The KWC PT92 CO2 Blowback Airsoft Pistol performed OK during my Field Test Shooting review in terms of accuracy. I shot it first in semi auto to get a sense of the overall accuracy and in terms of elevation it was right in the middle of the target. I did find the shots spread out a bit side to side perhaps as much as 4-5 inches during my test grouping. As expected when I flipped the happy switch to full auto the KWC PT92 CO2 Blowback Airsoft Pistol pretty much sprayed the target working its way up as the recoil from the full auto blowback action lifted the barrel. In terms of power the KWC PT92 CO2 Blowback Airsoft Pistol shot pretty hot, I was using .25 gram Airsoft BB’s and was still able to achieve close to 400 fps.
Build Quality: The KWC PT92 CO2 Blowback Airsoft Pistol like the other all metal KWC made Beretta 92 or Taurus PT92 copies out there being sold under different company names, is a good value blowback Beretta Taurus Airgun no matter which version you get. It’s not the best or worst, right about in the middle but most of the bugs have been worked out since it came out just after the KWC 1911 line and that’s been out for some time now. I find the finish does come off a bit easy but when this happens it kind of gives the Airgun a more realistic and slightly worn in look to it.
Realism: The KWC PT92 CO2 Blowback Airsoft Pistol is a One to One replica of the real steel Taurus PT92 and does a great job at replicating it. You would be hard pressed to see any differences in the Airgun version versus the 9mm caliber firing version until you pick one up and work the parts a bit. Even so pretty much all the mechanical parts work the same as a real steel Taurus PT92 including the ability to filed strip the Airgun version and gain access to the hop-up and other internal parts.
Pros:
All metal construction.
Full length blowback action with nice heavy recoil.
Accurate Taurus PT92 replica.
Single and double action triggers both feel good.
Double stack style metal magazine holds the CO2 and Airsoft BB’s.
No ugly white writing ( warning instructions) on the gun.
Fully filed strippable.
Adjustable Hop-up.
Recessed barrel for added realism.
FPS is fairly high for a full blowback gun.
Cons:
Finish on KWC guns can wear off quickly in the high spots but has gotten better over the years.
Full blowback action especially when in full auto mode will eat up a lot of CO2.
Comments: If you are a Beretta 92 or Taurus PT92 fan than I am sure you have already taken a look at the KWC line of Beretta 92 and Taurus PT92 Airguns, maybe in a steel BB version or Airsoft version? KWC first offered it in this PT92 style and then later brought out a more true to form Beretta 92 version. Depending on where you live and which model you buy you may or may not have the full auto feature but to be honest full auto is fun at first but then you realize you don’t really hit much with it and just end up wasting a lot fo CO2 and BB’s. Checkout our Replica Airguns Canada and US Stores for all the different versions and models of this KWC Beretta and Taurus style Airgun.
My Vimeo Video Review for the KWC PT92 CO2 Blowback Airsoft Pistol:
If you have not already watched my Preview video for both of these Airsoft pistols then make sure to watch that video for details and specifications along with some nice tight shots of each Airsoft gun.
Another multi gun Field Test Shooting Review, in this Indoor Sea Can Field Test Shooting Video I test out the KWC M1911 and PT92 Full Blowback CO2 Airsoft Pistols. I first place 5 6mm .25 gram plastic Airsoft BB’s through my Chronograph to find out what the real world velocity is for each Airsoft Pistol and then I perform my accuracy test where I shoot multiple rounds into a paper target 30 feet down range to see how close of a grouping I can get with each Airgun. I use a seated and rested shooting position to eliminate as much human factor as possible. By the way is used a brand new 12 gram CO2 and the temperature was 25 degrees Celsius (77 degree Fahrenheit) inside the Airgun Sea Can Shooting Range.
Starting with the KWC M1911 CO2 Blowback Airsoft Pistol I averaged 351 fps with the fastest shot being 353 and the slowest shot 345, so very consistent for sure! Accuracy for the KWC M1911 CO2 Blowback Airsoft Pistol could have been a bit better, I had to adjust my aim point to just under the bottom rings and even so the KWC M1911 wanted to shoot high, I was able to get around a 5 inch 10 shot grouping but was hoping for a bit better.
Next I tested out the KWC PT92 CO2 Blowback Airsoft Pistol which does have a full auto option. For the velocity portion of my Field Test the KWC PT92 did shoot a bit after than the MWC M1911 getting an average fps of 388 with the fastest shot hitting 396 and the slowest shot at 383 so again very consistent performance. Since the KWC PT92 CO2 Blowback Airsoft Pistol is capable of full auto shooting I decided to shoot 5 rods on my paper target to get a base accuracy and this resulted in a bit of a lateral spread fairly close to the bullseye about 4-5 inches apart. I then did a mag dump and as expected pretty much sprayed 6mm Airsoft BB’s all over the place but most shot a bit high and to the left probably because of the blowback recoil action.
The KWC M1911 and PT92 CO2 Blowback Airsoft Pistols are both classic Airguns and great options if your looking for a 1911 or Beretta styled Airgun to add to your collection without all the markings and white writing on them.
This Field Test Shooting Review for the Daisy Powerline 340 Spring BB Pistol is a lot different from most of my other shooting video reviews mainly because the Daisy Powerline 340 Spring BB Pistol is not a CO2 powered BB Pistol like pretty much every other 4.5mm Steel BB pistol I have ever tested. There are way more 6mm Airsoft spring pistols but when it comes to actual 4.5mm BB Pistols they are not very common. The Daisy Powerline 340 Spring BB Pistol is Kind of like the pistol version of the Daisy Red Ryder BB Rifle…
So let’s get right into the nitty gritty on how the Daisy Powerline 340 Spring BB Pistol performed in the Replica Airguns Indoor Sea Can Airgun Shooting Range. Starting off with the feet per second velocity for the Daisy Powerline 340 Spring BB Pistol Daisy claims around 240 fps. shooting about 8 shots through my chronographs with standard 5.1 grain 4.5,, steel BB’s I was able to get an average of just over 180 fps, the Daisy Powerline 340 Spring BB Pistol was super consistent shooting all shots between 181 and 189 fps.
I then proceeded to place 10 shots on my paper target setup 30 feet down range shooting from a rested portion with a sand bag up front supporting my hadbn’s and a stool to sit on in the back. The Daisy Powerline 340 Spring BB Pistol did shoot a bit low and to the left but all 10 shots grouped within 3 inches of each other, actually a bit better than I was expecting from a low cost BB Pistol like this. If I was shooting at a pop can and adjusted my aim point a bit I would have hit the can 10 out of 10 times which is about as good as you can ask for a plinker like this.
The best way I can describe the Daisy Powerline 340 Spring BB Pistol is the pistol equivalent of the Daisy Re Ryder in that it shoots 4.5mm Steel BB’s has a high capacity BB reservoir that holds lots of BB’s and you are required to cock the spring for each shot rather than use CO2 for power. This makes for an over low cost Airgun but like the Daisy Red Ryder it is a lot fo fun to shoot at the end of the day. The Daisy Powerline 340 Spring BB Pistol has a surprisingly good trigger and at the end of the day shot really consistently for me.
Type: BB Rifle. Manufacturer: Crosman. Model: R1 AR. Materials: Metal & plastic. Weight: 6 pounds (2.7 kilograms). Length: 26.25 / 29.25 inches (Stock closed / extended). Propulsion: 12 gram CO2 dual cartridges. Action: Blowback - single action only. Ammunition Type: 4.5mm steel BB's. Ammunition Capacity: 25 rounds. FPS: 430fps. Rate of Fire: 1400 rounds per minute in full auto
Trigger Pull: The trigger pull on the Crosman R1 CO2 Blowback BB Machine Gun is single action only since the charging handle must be cocked first before you can shoot it. The trigger is short and fairly light as you would expect from an AR type trigger action. The real fun happens with the Crosman R1 CO2 Blowback BB Machine Gun when you switch it over to full auto mode and with just one pull and hold of the trigger you empty the 25 round magazine in mere seconds.
Build Quality: The Crosman R1 CO2 Blowback BB Machine Gun is well made all around. Weighing in at 6 pounds without any add on accessories it feel solid and well built. There is a lot of metal going on inside and out of this rifle but keep in mind the top and bottom receiver are plastic with metal parts where they need to be like in the internals, pretty much all the working parts are metal, the magazine is full metal, the buffer tub is metal, charging handle, selector switch, magazine release, bolt release, trigger and of course the barrel is metal.
Realism: The Crosman R1 CO2 Blowback BB Machine Gun is about as real as you are going to get in a CO2 Blowback AR/M4 styled Airgun. You can even take it apart and split the top and bottom receivers like the real steal version. The blowback action gives you some recoil but more importantly offers a true single action trigger and of course the full auto ability we all love. Almost all the working parts work like they would on a real AR / M4 other than the forward assist which is moulded into the receiver.
Pros:
Super realistic working M4/AR 4.5mm BB Rifle just like the otters Crosman Rifles in this lineup.
Full blowback operation with both semi and full auto shooting, can feel the blowback operation rocking the gun.
Great weight and feel to it.
Almost everything works exactly like the real steel version. (Charging handle, dust cover, bolt release, magazine release, selector switch…)
Duel CO2 full metal drop out magazine that holds the 25 4.5mm steel BB’s as well.
Adjustable and customizable AR butt stock.
Included red dot sight and ability to add pop-up iron sights.
Lots of rails of mounting additional cool hardware.
Removable flash hider that uses standard threading.
Cons:
Receiver is plastic but well made and does not compromise feel or weight since there is lots of metal throughout this gun.
No iron sights included.
Comments:
The Crosman R1 CO2 Blowback BB Machine Gun is really pretty much the same as the Crosman DPMS SBR and Crosman MPW with more or less Cosmetic changes. Like the Crosman MPW the Crosman R1 has an AR compatible Rear stock and pistol grip, the Crosman R1 CO2 Blowback BB Machine Gun is the only Crosman AR Full Auto CO2 BB Rifle that has the ability to change out the flash hider, you can even put a mock suppression or in it if you choose to. No matter which of the Crosman AR Full Auto CO2 BB Rifles you chooses to get they are mechanically every similar and share most of the same parts. I would say the Crosman R1 CO2 Blowback BB Machine Gun is the most customizable to date but they are all fantastic Air Rifles!
My Table Top Video of the Crosman R1 CO2 Blowback BB Machine Gun:
Here we are with yet another Crosman AR styled Full Auto Blowback CO2 BB Rifle and they just keep getting better, I say that lightly as even the first version the Crosman DPMS SBR still holds up to the 3 part lineup. It kind of has to since all three of them can be mixed and matched in terms of the uppers and lowers, magazines and I am sure most intern parts. Check out the Crosman DPMS SBR and the Crosman MPW for reference as I have made full table top and field test shooting videos for them already.
The purpose as always for my Field Test Shooting Videos is to find out how the airgun being reviewed performs in terms of velocity and accuracy, and if the ratings on paper end up being the same or close to the tested results. Crosman claims the Crosman R1 CO2 Blowback BB Machine Gun is capable of shooting 5.1 grain 4.5mm Steel BB’s at up to 430 fps. When I tested the Crosman R1 CO2 Blowback BB Machine Gun using my Chronograph averaging out 5 shots using a brand new set of CO2 cartridges I averaged 395 fps. Note the temperature in my Indoor Airgun Sea Can Shooting Range was about average at about 24 degrees Celsius or right around 75 degrees Fahrenheit. Comparatively I was able to get 405 fps from the Crosman DPMS SBR and around 385 fps with the Crosman MPW. Temperature may have beene slightly different on those testing days so that needs to be factored in.
Moving on to the accuracy portion of this Field Test Shooting Review for the Crosman R1 CO2 Blowback BB Machine Gun, I placed 10 semi auto shots on my paper target setup 30 feet downrange. I was using a rested and seated shooting position to help minimize human factor. I was able to get pretty much a 1 inch grouping with my 10 semi auto shots which was nit surprising as I have been able to get tight shot placement like this from the Crosman AR series before.
I then flipped the Crosman R1 CO2 Blowback BB Machine Gun semi auto selector switch to full auto and dumped the remaining 10 rounds into my paper target in full auto mode flowed by another full 25 round magazine again in full auto and the grouping only stretched out to about 2.5 -3 inches even with all the full auto vibrations and rocking around of the gun. Shot placement was a little bit high and to the left but this can easily be corrected using the red dot sight adjustments.
In summary the Crosman R1 CO2 Blowback BB Machine Gun performed a lot like the Crosman DPMS SBR and the Crosman MPW which makes since since all of them are virtually mechanically the same. In the end I think it really comes down to which of the Crosman AR type full auto BB rifles you like the look of since they areal very capable shooters. If you can’t decide then maybe get one of each :)
Watch my Preview Video where I take a quick look at the Sig Sauer MCX CO2 Pellet Rifle and Crosman R1 Full Auto BB Rifle. Full Table Top and Field Test Shooting Videos coming soon.
As always I like to test each gun out in the Replace Airguns Indoor Sea Can Airguns Range first placing 5 rounds through my Chronograph to find out the real world velocity of each test gun, then I shoot 10 rounds at a distance of 30 feet onto a paper target to see how tight of a grouping I can get shooting from a seated and rested position. When it come to full auto BB guns like the Umarex Legends M1A1 Blowback CO2 BB Machine Gun, I will usually switch up to full auto and dump the rest of the magazine to see if I can still sray on target with the remaining rounds.
For my Power or Velocity test I was using fairly new CO2, I had shot a full magazine a couple days before but the Umarex Legends M1A1 Blowback CO2 BB Machine Gun was all warmed up and ready to perform optimally. Umarex does state that it will shoot around 435 fps and with my 5 shot test I was able to confirm that with a 434 fps average. The temperature in the Sea Can was around 23 degrees Celsius or 73 degrees Fahrenheit.
For my accuracy test I setup a new paper target 30 feet downrange and proceeded to place 10 shots into it using the peep sights on the Umarex Legends M1A1 Blowback CO2 BB Machine Gun. Other than one slight flyer my 10 round grouping was around 3/4 of an inch and just a tad low of the bullseye but pretty close. I then switched over to full auto fun mode and with the remaining BB’s I unloaded all 20 rounds in about a half a second, or at least it seemed like that! The Umarex Legends M1A1 Blowback CO2 BB Machine Gun even in full auto mode with the trigger matted till the gun ran out I was still able to get a 2 inch grouping!
I’m a big fan of the Umarex Legends Series BB Guns and the Umarex Legends M1A1 Blowback CO2 BB Machine Gun may be my favorite out of all of them to date. The Thompson M1A1 is just such a stand out Machine Gun we all know from the Mob shows. Not only does the Umarex Legends M1A1 Blowback CO2 BB Machine Gun look the part but it performs I would have to say so far the best when it comes to Full Auto Machine guns at least from Umarex. I do have to say that the Crosman CO2 BB AR Series does not disappoint. That said if you are looking for a more classic BB Machine Gun that performs as good as it looks then my advice is grab yourself one of the Umarex Legends M1A1 Blowback CO2 BB Machine Gun and add it to your collection.
