Another preview video with some pistols from Umarex, ASG and Gletcher. Two of these Airguns I got to see whiel I wa sin SHOT Show this year so it was nice to be able to spend a bit more time with each one now that I have them in person for review :)
Lets start off with the ASG Dan Wesson 715, mine happens to be the Stainless version in 4.5mm Steel BB. What an upgrade over the original Dan Wesson Revolver and I thought those where already really good! The all new ASG Dan Wesson 715 is super solid coming in close to three pounds with its mostly solid metal construction.
Next up is the Umarex Combat Vet 1911 which is essentially a KWC 1911 distributed and Colt licensed via Umarex. The Umarex Combat Vet 1911 is a limited edition product made to look weathered and used and it does look amazing!
Lastly the Gletcher Stechkin in a Gold finish shipped in a real wood box with velvet lining. This is the same Airgun as the Gletcher APS but blinged out a bit, the Gold finish is lined with black etching to really make this gun look unique.
Ammunition Type: 4.5mm steel BB's. or .177 cal. pellets.
Ammunition Capacity: 6 rounds.
FPS: (BB 410) (Pellet 380).
Trigger Pull: Trigger pull on the John Wayne Duke Colt SAA BB and Pellet Revolver is the best I have ever come across in an airgun. Being that these Single Action Army Revolvers are single action only, most of the work is done while you pre-cock the hammer. The trigger pull is under 2 pounds and has virtually no take up with a crisp release. I love the ratcheting sound as you pull back the hammer just like using a real SAA Revolver!
Accuracy: I have not yet tested these John Wayne Duke Colt SAA BB and Pellet Revolvers so far but expect the BB version to perform for the most part just like the Umarex only versions I tested previously. Here are my notes from my previous testing:
"I tested both 4.5mm steel BB's and 4.7mm Lead ball BB's in the Umarex Colt Single Action Army Shell Loading BB Revolver. With the Steel 4.5mm BB's I shot just under a 2 inch 6 shot grouping when shooting from a 30 foot distance using a semi rested position (Sand bag up front, standing in the back). The shots where pretty well center hitting the paper target just a little bit high, they did seem to stray a little more left and right rather then up and down. When I switch ammo to the 4.7mm Lead BB's I got a similar 2 inch grouping but they hit the target a bit lower and tended to shoot tighter from side to side with more variation up and down, perhaps because the lead BB's did not seem to shoot at a vary consistent velocity. My Chronograph testing for the Steel BB's was right around 400 fps while the Lead BB's being heavier shot a bit slower at just under 300 fps."
Build Quality: The John Wayne Duke Colt SAA BB and Pellet Revolvers have a mostly all metal construction other than the plastic grips and any seals. The fit and finish is excellent with a great overall weight in the hand. Whether you get the Nickel or Weathered version. The mechanical action of the hammer and trigger feels just like it would on a real single action army revolver.
Realism: In terms of replicating a real steel Colt Single Action Army Revolver, these guns are absolutely amazing replicas. It's really hard to tell the airgun version from the real steel version, except for the smaller in diameter shells and the discreet safety switch located under the frame. Even the barrel is nicely recessed and has some fake rifling twists in it to give the appearance of a large caliber round. The CO2 is well hidden with the Allen key built into the handle so no ugly CO2 screw tab hanging down.
Still the best airgun reproduction of the Single Action Army Revolver, a very accurate replica of the real steel old west version.
Recessed barrel has the look of a large caliber bullet.
Great weight and feel in the hand.
Shell loading design that loads from the back so no need to remove shells if you wish not to.
Hammer and trigger action is about perfect, no take-up, very crisp and super light (under 2 pounds).
Finish on both the Nickel and Blued is very nice.
Colt and John Wayne Duke licensing.
Very well concealed CO2 with built in Allen key.
Discreet safety location.
If you prefer pellets over steel BB, now you have the option.
Cons:
Still has the warming instruction on the right side of the barrel but not super obvious especially on the Nickel version.
Real version would shoot 45 caliber, dummy shells are actual closer to 357 so a bit smallish.
Wood grips to me look a little fake up close but the John Wayne emblem kind of makes up for it.
Comments:
Shell loading BB and Pellet revolvers have been out for a while now and have changed the way many of us feel about airgun revolvers. Airgun revolvers used to be kind of overlooked because they where not the most exciting replica airguns out there but now we have not only the new Dan Wesson 715 shell loading revolvers but also these Colt Single Action Revolvers with Colt and John Wayne Duke licensing on them available in both BB and pellet shooting versions! There is something special about these old cowboy day classic revolver that makes them so elegant and just a real work of art you can not only own and look at but also take out and shoot whenever the spirit moves you to do so!
My Vimeo Table Top Review for the John Wayne Duke Colt SAA BB and Pellet Revolver:
Trigger Pull: The trigger pull on the Air Venturi ISSC M22 CO2 Blowback BB Pistol is pretty decent overall. Unlike the original 22LR ISSC M22 that is single action only, the BB version shoots on both single and double action. When shooting in double action, the trigger pull is a little bit heavier since the hammer is not pre-cocked but shooting in single action does require full trigger pull length since the first stage of the trigger pull chambers a BB into the breach area. The second stage when shooting in single action releases the hammer.
Accuracy: I have only shot the Air Venturi ISSC M22 CO2 Blowback BB Pistol briefly, and only using a free standing position shooting at some pop cans. I did notice the Air Venturi ISSC M22 CO2 Blowback BB Pistol shot a little bit low at 20 feet but was well centered side to side. The BB's seemed to travel pretty quick and the blowback action was snappy and allowed for some pretty decent rapid fire action. I will be following up this table top review with a field test shooting video down the road.
Build Quality: I was impressed with this pistol right out of the box, being an owner of the real steel 22LR version, I was actually rather surprised at how accurate of a reproduction in terms of build quality the Air Venturi ISSC M22 CO2 Blowback BB Pistol was. The BB ISSC M22 has a good weight and feel to it and metal and plastic parts in pretty much all the same places you would find them in the 22LR shooting version. The plastic frame feels solid and well made while the metal slide has very close tolerances and the black satin finish looks good and seems to be wearing pretty well.
Realism: Again as an owner of the first generation real steel 22LR ISSC M22, and placing these guns side by side, they are nearly undistinguishable other than the changes Glock had ISSC make to the current versions so yes there are some cosmetic differences between my first generation M22 and the current version of this replica BB ISSC M22. That aside if you are an owner of the 22LR ISSC M22, then you are going to have to have one of these Air Venturi ISSC M22 CO2 Blowback BB Pistol to go along with it for even cheaper cost per shot then 22LR ammo. In terms of working parts, everything is the same except for the de-cocker since the BB model de-cocker is moulded into the slide and none functioning. I wish the Air Venturi ISSC M22 CO2 Blowback BB Pistol was easily filed stripable but I guess you can not have everything :)
Pros:
Really great overall replace of the 22LR ISSC M22.
Metal and plastic parts in all the same places as the 22LR ISSC M22.
Full blowback operation with single action trigger.
Full size drop put metal magazine that holds the CO2 and BB’s
Almost all mechanical parts work the same as the 22LR ISSC M22. (exception of slide safety)
ISSC m22 licensed.
Adjustable rear sigh for windage.
Accessory rail for addons.
One of the closest 4.5mm Steel BB pistols to a Glock that we have available to us.
Cons:
Does not seem to field strip at least easily.
Slide safety is module into slide and none functioning.
Comments:
All in all this may just be my new favorite blowback BB pistol, I obviously like the design since I already own the 22LR version and it does look a lot like a Glock so that may be a benefit to you Glock lovers out there. The Air Venturi ISSC M22 CO2 Blowback BB Pistol really does seem to have a lot going for it... Blowback operation, a full size drop out metal magazine that holds the CO2 and BB's, decent fps and accuracy, an adjustable rear sight, working parts where they are supposed to work on the real steel version and that Glock look and feel but without the worries of Glock coming after you for violations of their copywrite since this is a licensed ISSC M22 replica.
My Vimeo Video Review for the Air Venturi ISSC M22 CO2 Blowback BB Pistol:
In this 2016 SHOT Show Interview I talk with Bob Li from Action Sport Games. Bob shows me some of the new products this year from ASG. Some of ASG's newer pistols are the Dan Wesson 715, the CZ 75 SP-01 Shadow, the CZ P-09. New to the rifle line is the CZ Bren 80, also a couple of sniper rifles, the M40A5 and M40A3. ASG is also coming out with a an Inferno HPA version of their CZ Scorpion EVO 3A1.
The ASG Dan Wesson 715 has ot me my favorite product from ASG, you need to hold it in your hand to really understand how solid this pistol really is at close to 3 pounds. Everything about it is an improvement over previous Dan Wesson models including the trigger and hammer action, crane setup and the more actuate frame length with the new more compact internal CO2 valve. The ASG Dan Wesson 715 will be shipping in 4.5mm Steel BB, 6mm Plastic Airsoft and .177 caliber pellet versions.
ASG's two new Full blowback CZ 75 SP-01 Shadow, the CZ P-09 pistols should be coming out shortly, both will be available in 4.5mm Steel BB and 6mm Plastic Airsoft. Both pistols feature a metal slide and frame with full size drop out metal magazines and will have CO2 and Green Gas magazine configurations. The CZ P-09 will have a threaded barrel and barrel protector.
In this 2016 SHOT Show Interview I talk with Nichol Goines from Umarex USA. Nichol and I discuss some new and somewhat revised products from Umarex like the Full Blowback Smith & Wesson M&P40, the soon to finally be released Beretta Model 92 A1, a new Pellet version of last years Colt Single Action Army Revolver and a reappearance and revision of the Walther PPK CO2 Blowback BB pistol.
Last year Umarex introduced their Colt Single Action Army CO2 BB Revolvers and I would say last year they where on of my highlight airguns for the show. They have been selling like gang-busters! One question people have been asking is if there will be a pellet shooting version? Well now there is and like the Steel BB version the pellets load from the back of the shell making it super easy to reload the removable brass shells. The new Pellet SAA Revolver also has a rifled barrel to help with accuracy.
M&
I would have to say this years gun highlight well at least from Umarex is their new Smith & Wesson M&P40 full blowback CO2 BB Pistol. It is a perfect copy of the real steal version complete with a full size drop out magazine and full Beretta licensing. I really hope this one ships soon and does not get delayed like the Beretta Model 92 A1 introduced last year and still yet to be shipped :(
Speaking of the Beretta Model 92 A1 CO2 Blowback BB pistol. It is finally getting released this February and like the S&W M&P40, is a virtual identical replica of the original Beretta Mod. 92 A1 complete with full blowback, a full size drop out magazine and of course all the trades and licensing in all the right locations.
Last and not least but still worth noting is the CO2 Blowback BB shooting Walther PPK. It kind of dropped out of productions which is a real shame since it was the replica BB pistol that got all of this started for me several years back and to this day is still a lot of fun ot shoot! Even James Bond went back to the PPK for the latest 007 movie! Well it's back and this time Umarex got rid of the ugly CO2 tab and replaced it with a discreet Allen key screw. Saves us all from doing the CO2 screw mod :)
This is my SHOT Show 2016 Teaser Video! You will get to see some new gun highlights from companies like Umarex, ASG, Crosman, Sig Sauer, KWA and ISC. I will be following up this video with some interview videos very soon so do make sure to check back for those uploads. All I can say about the show is it’s huge! So much to see, so much walking and too much to take in…
ASG:
As always, ASG had some new products this year. The all new Dan Wesson 715 357 Magnum shell loading Revolver! This gun feels absolutely amazing in the hand and will be available in Steel BB, Airsfot and even Pellet shooting versions. Also new are the CZ P-09 and CZ 75 SP-01 Shadow Full Blowback BB and Airsoft Pistols.
Crosman:
Big at Crosman this year was their PCP Airbow, Crosman put a lot of focus on this product and even had a lot of crossbows on display to go with their new PCP Airbow. Crosman also introduced their low cost entry level Benjamin Maximus PCP rifle in .177 and .22 calibers offerings. Not really much in the way of replica pistols from Crosman this year, but then again last year was kind of the same?
Sig Sauer:
I finally made it to the Sig Sauer Booth this year to checkout their new CO2 Pellet gun line. All new Sig Airguns are made true to size and weight with similar trigger actions as their real steel versions. The Sig MPX is their more compact (shorter barreled) pellet shooting CO2 rifle with internal blowback and belt fed 30 round magazine. The Sig MCX is the longer barreled rifle version but built much the same as the MPX. Sig also introduced two new pellet shooting CO2 Blowback Pistols, the P226 and the P250. Both use similar double ended rotary magazines as the Umarex PX4.
Umarex:
Umarex always seems to have some new exciting Airguns products to offer at SHOT Show. The PPK is back with a few updates including no more ugly CO2 tab sticking out of the bottom! And yes the Beretta Model 92A1 will finally be shipping soon, I believe in February! My favorite product this year from Umarex would have to be the Full Blowback, Full size drop out magazine S&W M&P 40 CO2 BB Pistol. Umarex released yet another 1911 on the market, this version does come with a stick mag and sports pretty high fps and more shots per CO2 then the KWC based 1911’s. The super popular Colt SAA Revolver is now available in a pellet shooting version with a rifled barrel :) Umarex had on display another low cost revolver, the ultra futuristic looking Brodax CO2 BB Revolver.
KWA:
KWA always has really nice high quality products to showoff at there booth each year, we may even start carrying some of KWA's products this year, fingers crossed on that one… New to the KWA line are some AEG rifles with simulated blowback action, I really liked the Blowback AEG AK they had on display. KWA also released a new Airsoft shell loading revolvers that had some of the nicest looking brass and aluminum shells. On display under a glass cover was a very solid Gas Blowback Thompson Machine-gun with real wood stock, it was absolutely gorgeous!
ISC:
ISC known for their top quality AEG internals, had their full line of high quality Airsoft rifles on display. And new this year to ICS was their first ever Airsoft pistol, the blowback BLE Alpha. The BLE should be out mid year and looked and felt really nice. The trigger on it was super short and light.
I have some really awesome Interview videos I’m working on, I will be uploading them shortly so stay tuned for those…
I just got some really interesting new guns and shooting accessories I wanted to share with everyone in this Vimeo Video Preview!
First off, I have some metal targets designed for Airguns, you can shoot them with lead pellets and heavy gram Airsoft BB's but be sure not use standard 4.5mm steel BB's as they can ricochet and come back at you at high velocity. That is unless you are using the new Excite Low Ricochet Smart Shot BB's I also showcase in this video.
A couple other accessories I highlight are a Western Leather Gun Slinger Belt and Holster which pair up perfectly with the first BB gun I have to show you today. Most of you should be familiar with the Umarex Colt Single Action Army Revolvers I have made several reviews and videos for, they are super popular and for good reason. How about a John Wayne Duke Version available in Stainless and Antique versions? I thought you would like that!
Next up and probably the item I am most excited to introduce to everyone is the ISSC M22 4.5mm CO2 BB Pistol. I actually own the first generation ISSC M22 in 22LR, the same gun this BB pistol is based on. It seems to have everything going for it and I was happy to discover after making this video that it does in fact have blowback operation even though this is not state on the box or in the manual? The ISSC M22 really is a beautiful pistol and I am totally looking forward to reviewing it. If you're a Glock fan this is about as close as we can legally get to owning a replica Glock BB pistol since Glock has OK'd production of the real steel ISSC MK22 in its new form.
I will be working with my suppliers to make these items available in our Replica Airguns Stores as soon as we can...
When I say Airguns, I am referring to pretty much all BB, Airsoft, Pellet, Paintball and even Blank guns for most of the topics listed here.
Do’s:
Treat your Airgun just like you would a real gun. If something goes wrong, perhaps the outcome will not be as severe but do you really want to take a trip down to your local emergency ward to get a BB or Pellet removed?
Always assume your airgun is loaded, for some reason it always seems those empty guns are the ones that do the most damage.
Be discrete, If it looks like a gun other people will think it is a gun so don’t flash your airguns around in public. Keep it in a case when transporting and shoot it in an area that will not alarm other people.
Always wear eye protection when shooting your Airgun. Do you really want to shoot your eye out? No Joke!
Be aware of your surroundings like windows, hard objects that could make your ammo bounce back at you. Make sure you are shooting your Airgun in a safe direction at all times, know your target and beyond.
Use Airguns to teach others and learn how to safely and effectively shoot a gun. Airguns can be less intimidating then a real gun (Not so loud and very little recoil) and make for great start out and transitions guns.
Use Airguns to get more inexpensive trigger time and become a more experienced shooter. Airguns cosy only pennies per round to shoot and can be shot in way more areas than a real gun can, practice makes perfect so get shooting!
Use Airguns in areas where real guns may not be allowed or safe to use. Again, Airguns can be shot in all kinds of places, in your back yard or even in a properly setup indoor home range.
Use Airguns with adequate power for safe and humane pest control where real guns may be prohibited.Airguns are quiet and less likely for the bullet to travel long ranges which makes them ideal for close range pest control in areas where real guns are too loud and to powerful.
Don’ts:
Do not assume because it is an airgun it is not dangerous or simply a toy. Many Deaths have been caused by Airguns along with a lot of pain and suffering so treat your Airgun with respect. It is not a toy or you would find them in the toy department at your local store along with yo-yos and stuffed animals.
Do not point or shoot at people unless of course you are using an Airsoft gun in an Airsoft field or facility. Yes Airsoft guns are meant to shoot at each other (with appropriate attire like eye protection and full body clothing), but steel BB and Pellet can cause serious injury especially at close range and on direct skin contact.
Do not leave your Airgun loaded, you never know who is going to come across it and accidentally discharge it. Remember, a loaded gun is a dangerous gun in the wrong hands. You may know better than to assume the gun is undulated but children and even adults without any gun training will most definitely handle the airgun without consideration of the danger it poses.
Do not use an Airgun for self protection. See my related video. Simply put, Airguns are not practical for self defense because they rarely have enough Stopping Power. The ones that do have enough power need to be pre-charged and in most cases are only single shot meaning if you miss or don’t get the job done no the first shot then you are done.
Do not use an underpowered Airgun for pest control. See related video. Using a low powered BB pistol for pest control is cruel, you will only injure the animal making it suffer unnecessarily. Use a high powered pellet rifle to get the job done.
Do not take your gun apart, in most cases this will void the warranty and the reality is that airguns rarely need to be cleaned since no dirty gun powder is used. lead pellet rifles may require occasional barrel cleaning to keep the rifled barrel free of debris.
Do not over oil your Airgun, a little goes a long way and too much oil will just attracted dirt, use the right airgun oil and just enough to keep part functioning smoothly.
Do not over pump an Airgun. Over pumping an Airgun can cause damage to valves and seals and in a worse case situation a rupture the air pressure reservoir or even cause the airgun to explode!
Can I use Airsoft BB's in my BB Pistol? I would have to say this is by far the number one question I get asked in the comments section of my Vimeo videos. I have made several videos where this question gets addressed within the video but so far to date I have not made a stand alone video just covering Airsoft BB use in BB Guns.
So here it is, and now I have a video I can link to this so very common question, if you where wondering about this yourself than please watch my YouTube Video on this topic as it goes into a fair amount of detail about it.
The short answer to this question is no, you can not use 6mm Airsoft BB's in a 4.5mm Steel BB Pistol or Rifle. For the simple reason that 6mm is larger than 4.5mm and so the physical diameter of a6mm Plastic Airsoft BB is just to large to fit inside of a 4.5mm Steel BB magazine or barrel.
People have commented about using a 4.5mm plastic Airsoft BB in a 4.5mm BB gun and yes this could in theory be an option but I discuss why I feel this is not a good idea based on size and mass.
In this video I feature my top five favorite BB pistols for early 2016. That said there are lots of other BB pistols I truly love and enjoy but I had to pick 5 so these are them! You may notice that many of them are blowback, I do like the blowback guns after all and this is my top 5 pick so naturally many of them will have blowback action.
Here is a list of my top 5 guns featured in this video not necessarily in order of choice:
With the popularity of the KWC - Cybergun 1911 Blowback CO2 Pistols and how super realistic they are in so many ways, it is no surprise that people often ask me if they can replace the original grips with grips made for a real 1911.
The short answer is yes you can! You will have to be prepared to remove just a little bit of material from the backside of both grips near the bottom of the handle where there is an area that has been flared out to accommodate the CO2. Not really a big deal, you can use a Dremel for the quick and easy approach or even some sand paper if you don't mind taking a little more time.
I'm getting close to uploading 600 videos now over on the Replica Airguns Vimeo channel, so there are bound to be a lot of similar questions and popular discussions. In this Replica Airguns Vimeo Video I address what I feel are my Top 10 Most Common Airgun Questions and Discussions.
Trigger Pull: The trigger on the G&G GR14 Type 57 R.O.C. is like most AEG Airsoft Rifles, being that it is essentially an electric on off switch and not a mechanical one. So it is light with not much take up. You will notice a bit of delay from the time your press the trigger till a BB is released since the electric motor must first pull back the spring and release it.
Accuracy: So far I have not tested out the G&G GR14 AEG Type 57 R.O.C. Walnut Wood Stock Airsoft Rifle. When I get the chance, I will have to set my paper target up further out than my usual 30 feet! I am also expecting the fps to be a bit higher than the stated factory default since this G&G GR14 AEG Airsoft Rifle is marked as being the "High Muzzle Velocity Version"! Stay tuned for my future Field Test Shooting video for the G&G GR14 AEG Type 57 R.O.C. Walnut Wood Stock Airsoft Rifle.
Build Quality: The G&G GR14 AEG Type 57 R.O.C. Walnut Wood Stock Airsoft Rifle looks to extremely well made with most of the build materials being metal and wood. The only none metal or wood noticeable parts would be the upper hand guard which is made out of some sort of nylon or plastic. I believe the original M14 Rifle upper hand guard was made out of fiberglass. Then Walnut Wood Stock is nicely finished and the metal parts function and look really great.
Realism: In terms of realism the G&G GR14 AEG Type 57 R.O.C. Walnut Wood Stock Airsoft Rifle is extremely authentic in terms of looks, weight and even overall length and barrel length! Most of the parts operate exactly as they would on the real M14 rifle including the selector switch, safety, magazine release, shoulder rest adjustable sights and bolt.
Lots of metal and wood parts where they would be on the real M14.
True realistic 9 pound weight.
High capacity magazine at 470 rounds.
Sights are adjustable for elevation and windage.
Semi and Full Auto selectable.
Real Walnut Wood Stock.
Flip up metal shoulder rest.
Engraved with "The Republic of China" Chinese Text Markings.
25000 rpm Hi-torque Long axis Motor with 7/8 mm Bearings.
8.4v Large Tamiya Battery System.
Cons:
Does not come with battery or charger.
Not setup as is for a scope.
Comments:
History of the M14 this rifle is based on - "The M14 rifle, formally the United States Rifle. M14 is an American selective fire automatic rifle firing 7.62x51mm NATO (.308 Winchester) ammunition. It was the standard issue U.S. rifle from 1959 to 1970. The M14 was used for U.S. Army and Marine Corps basic and advanced individual training and was the standard issue infantry rifle in CONUS, Europe, and South Korea, until replaced by the M16 rifle in 1970."
So the M14 has a place in our history books and also a place in many of our war veterans hearts. This G&G GR14 AEG Type 57 R.O.C. Walnut Wood Stock Airsoft Rifle replica is an excellent example of such a great piece of history, to have one in a working Airsoft version may be the next best option to having the real deal.
My YouTube Review Video of the G&G GR14 AEG Type 57 R.O.C. Walnut Wood Stock Airsoft Rifle:
Whether you like it or not, most of us have come across an Airgun with an ugly orange tip on it at some point. In most cases you will find the intrusive orange or red tips on Airsoft guns that shoot plastic BB's, in some cases you will even find them on Airguns that shoot either lead pellets and/or steel BB's.
It really comes down to where you live as to what your local gun laws have determined is required for your area. You may even live in a region where Airguns and Airsoft guns are not allowed at all! So for you a red or orange tip on the front would be welcome if it would allow you to own an Airgun or Airsoft gun. What about the entire gun being painted a bright color, well that is the case for some folks so again having a red or orange tips may not be as bad as it originally seemed...
In Canada where I live, we used to only be allowed Airsoft guns that had clear sections as our replica gun laws are very strict and all black Airsoft guns would have fallen iinto the "replica" category if they did not have large clear plastic see-through sections on them. This clear section law was revised somewhat over the last several years to allow for all black Airsoft guns here in Canada. It was determined that many Airsoft guns with higher fps limits could cause a serious injury to a human, making them less of a toy in the eyes of the law and more of a weapon. Because of this, Airsoft guns that are capable of shooting a .20 gram plastic BB at a velocity of 360 fps or "higher" are now considered to be similar in the eyes of the law to a regular steel BB or lead pellet shooting Airgun. In Canada, Pellet and Steel BB guns are actually considered firearms of a sort so this allows the higher fps Airsoft guns to be all black since it can not be a replica of a firearm if it is in fact considered to be a firearm by law.
The long and short of all of this is that here in Canada we do not require our Airsoft guns to have orange or red tips since they are considered more or less to be just like any other Airgun and our Airguns do not have red or orange tips either.
Getting back to the title of this article "No Orange Tip On Your Airsoft Gun! Are You Insane?" I often get folks from the US giving me heck for removing the orange tips from my Airsoft guns or asking me why my Airsoft guns don't have them in the first place. These people even state that I could get in a lot of trouble for this! Perhaps they think I live in the US or that US laws govern Canada as well? I am not sure but I can say for the record that I am not breaking any laws at least here in Canada where I live.
I know in the US that wholesalers and retailers by law have to sell Airsoft guns with the affixed orange tips on them, once the end user receives that gun and depending on which state they live in, it may or may not be legal to remove the orange tip. Again, you will need to look into your local state laws as they are different from state to state in the US.
In this Video Review I show you around the G&G CM16 Raider and Carbine AEG Airsoft Rifle's. Since these AEG Airsoft AR Rifles are a bit large to showcase using my traditional Table Top location I move into my gym and take each gun out of its box to have a good look at them. I talk about some of the main features and specification. The main features being these G&G CM16 AR15 / M16 AEG Airsoft Rifles are all really well priced but also very well made for their rather low overall cost. They do have a primarily all Nylon Fiber build even in the receivers but they still have a nice 4.6 to 5.7 pound weight to them, and once dressed up with a few accessories they come in at a perfect weight that is not too heavy to carry around in just about any game situation. The Nylon material in some way is a better choice in terms of getting scratched and dinged since they will not mark up as easily as painted metals will.
I don't often review target and or hunting rifles since for the most part Replica Airguns is all about well... replica airguns :) I have reviewed some of my own personal spring piston and pump rifles since I have them and there is a cross over in folks that like both the replica airguns and airguns meant for target and or hunting purposes.
We do have a small selection of spring piston rifles in our Replica Airguns Canada store suitable for target and small game so I thought I would point some of them out in this preview video.
Action: Semi auto non-blowback, double action only.
Ammunition Type: Steel BBs 4.5mm.
Ammunition Capacity: 21 rounds
FPS: 394 fps/ 120 m/s.
Trigger Pull: The trigger pull on the KWC Metal Slide CQBP M45 A1 Non-Blowback CO2 BB Pistol was about medium to hard but I have definitely experienced heavier trigger pulls on some guns. It is nice that the trigger is in the style of a 1911 and not your typical lever styled trigger like you will find on some 1911 wannabe's. I imagine if the CQBP M45 A1 has a lever style trigger it would have more leverage and be a bit lighter.
Accuracy: I have not shot the KWC Metal Slide CQBP M45 A1 Non-Blowback CO2 BB Pistol but expect it to perform similar to the Cybergun Sig Sauer GSR Sigarms I reviewed a while back since both guns have similar internals so for now until I do my dedicated Field Test review you can read my Cybergun Sig Sauer GSR Sigarms Review: "Accuracy was decent but not outstanding, I got around a 2.5 inch grouping from a 20 foot away free standing position, shooting just to the left and high on the target. I did find that I was able to zone in a bit better with the Cybergun GSR as I got used to the trigger. I also put the Cybergun Sig Sauer GSR through my Chrony Chronograph and got very close the manufacturers 397 claimed feet per second, actually starting off well above it and settling down to around the 370 FPS mark. My 8 shot average on a new CO2 was actually 422 FPS."
Build Quality: You will find a pretty nice balance of metal and plastic on the KWC Metal Slide CQBP M45 A1 Non-Blowback CO2 BB Pistol. The metal slide, magazine barrel and some literals give it a really decent weight in the hand and the fit and fish feel good overall. The trigger and hammer are not the best aspects of the gun in terms of quality as they are both plastic and both kind of made more for show and less for function.
Realism: The KWC Metal Slide CQBP M45 A1 Non-Blowback CO2 BB Pistol looks and feel the part of a M45 1911 A1 including a full size drop out metal magazine, working magazine release and safety. The slide catch release is none functioning and so is the hammer which does not cock back for single action shooting. It would have been nice to have a single action trigger and a working slide to finish off this pistol but it is meant to be more of an entry level pistol at the end of the day.
Should have good FPS and lots of shots per CO2 based on my 4.5mm BB version testing!
Rail for mounting accessories.
Nice white dot sights.
Recessed barrel give it a more realistic look.
True 1911 style looking trigger even though it is double action only.
True 1911 working safety.
Cons:
No blowback - slide does not move either.
Hammer moves but does not cock so no single action shooting.
Non adjustable rear sight.
Trigger action is bit heavy and long so it’s not going to be the fastest action shooter.
Comments:
If you're looking for a lower cost well made 1911 in that classic A1 style but with a little bit of updating like having a Picatinny rail and tactical sights then the KWC Metal Slide CQBP M45 A1 Non-Blowback CO2 BB Pistolmay just be right for you. So it doesn't have blowback or a working slide, on the other hand it has lots of metal on it giving it good weight and feel and with less moving parts there will be less to go wrong down the road. You can also expect to get fps into the 400 range with a decent amount of shots per CO2 so the trade off not having blowback may be worth it for this reason. All in all a nice airgun in the under $100 category.
My Vimeo Videos for the KWC Metal Slide CQBP M45 A1 CO2 Air Pistol:
Trigger Pull: The trigger pull on the KWC Mac 11 M11 is double action only and is rather long and a bit firm so you will get a bit of a finger workout especially when shooting a full 39 rounds from the 4.5mm steel BB version. There is no blowback operation so this is a double action only pistol.
Accuracy: The accuracy and true feet per second performance will be tested when I do my future Field Test Shooting Review shortly (weather permitting).
Build Quality: Overall the KWC Mac 11 M11 CO2 BB - Airsoft Pistol is built fairly well as long as you don't mind the all plastic build. to be honest if you where to drop this all plastic pistol on the ground it would most likely just bounce a couple of times no worse for wear since it is kind of light weight and all. If it was an almost all metal build it would weigh in a lot more and the drop onto a hard surface could easily break the zinc alloy metal parts. That said there is some metal on the KWC Mac 11 M11 CO2 BB - Airsoft Pistol and that would be the folding - sliding stock and of course some internal parts. The rear fold out portion of the stock is actually hardened steel!
Realism: As a replica of a real steel Mac 11 M11, the KWC Mac 11 M11 CO2 BB - Airsoft Pistol looks bang on since it is 1 to 1 scale and at least in terms of looks is virtually identical ot teh real Mac 11. In terms of function, that is a different story since the KWC Mac 11 M11 CO2 BB - Airsoft Pistol does not have many working parts other than the trigger, safety and magazine release. The selector switch, bolt charging handle and bolt are all molded into this gun and their only purpose is to look good! The overall weight is rather light too since most of this Mac 11 pistol is ABS or plastic.
Pros:
First 4.5mm Steel BB Mac 11.
1/1 scale replica definitely looks the part.
Full size drop out magazine that holds the CO2 and BB’s.
High capacity 39 rounds magazine.
Built in metal and steel retractable stock.
Decent fps.
Available in both 4.5mm Steel BB and 6mm Plastic Airsoft versions.
Cons:
Pretty much all ABS, kind of light weight.
No blowback or many working parts.
Kind of long and heavy trigger.
Pretty much everything is moulded into this gun.
Comments:
Too be honest when I first saw the box for the KWC Mac 11 M11 CO2 BB - Airsoft Pistol I was a bit excited, that was until I opened it up and found out I was looking at a pretty much all plastic gun with few working parts and no blowback operation. But after holding it and giving this air pistol a good look over I have to say I am warming up to it a bit more now. After all it is the first Mac 11 M11 4.5mm steel BB pistol that I know of and it 100% looks the part so if you are looking for a replica Mac 11 then this will fill that purpose for sure. Even though it is almost all ABS plastic, this airgun feels solid seems to be really well made. The steel and metal stock is a nice addition and so would have been a metal magazine but overall for a low cost replica BB and Airsoft shooter you do get your moneys worth.
My Vimeo Video Review for the KWC Mac 11 M11 CO2 BB - Airsoft Pistol:
Trigger Pull: The trigger pull on the KWC Makarov PM CO2 Blowback BB Pistol is really nice. It is single action only since it is a blowback pistol that requires racking the slide to chamber the first round. The take-up of the trigger is slight with a crisp light release, the trigger is definitely not going to get in the way of the accuracy of this pistol.
Accuracy: The accuracy and true feet per second performance will be tested when I do my future Field Test Shooting Review shortly (weather permitting).
Build Quality: Excellent, the KWC Makarov PM CO2 Blowback BB Pistol seems to be really well built like the other full blowback KWC BB and Airsoft pistols I have reviewed and shot in the past. The fit and finish is very good but I expect the electromagnetic black coating to wear off in the high spots fairly quickly but this does give the slight worn in real gun look. In terms of quality it looks like KWC may have even gone to extra effort to beef up some of the areas perhaps prone to breakage like the trigger guard since this pistol is made out of Zink based metals rather than hardened steel like you would find in the real firearm.
Realism: I have to say the KWC Makarov PM CO2 Blowback BB Pistol is a really nice replica overall, perhaps one of the best considering it has full cycle blowback with an all metal full sized drop out magazine. Sure the Baikal MP-654K takes the cake in terms of realism since it is practically a real Makarov rechambered to shoot Steel BB's but the MP-654K lacks blowback operation and the ability to fire quickly using a single action trigger. A couple of drawbacks with the KWC Makarov PM CO2 Blowback BB Pistol that are different from the real steel Makarov PM are the thicker trigger guard and butt plate.
Pros:
Has full cycle blowback operation.
Nice heavy blowback spring makes slide nice and snappy, should have good blowback operation.
All metal build.
All metal full size drop out magazine that holds the BB’s and CO2.
Fully field strip-able.
All part function like a real Makarov.
Open ejection port and reassessed barrel.
No ugly CO2 tab.
Seems to have a really nice single action only trigger.
Internal fixed hop-up for improved accuracy and sustained trajectory.
Cons:
Lower fps because of short barrel and presumable heavy blowback operation.
Magazine base sticks forward a bit more and is thicker than a real steel Makarov.
Trigger guard looks to be thicker than a real steel Makarov.
Comments:
The Makarov is one of my favorite pistols, it's a true classic! So the fact that there is yet another Makarov Air pistol on the market is fine with me. And perhaps the KWC Makarov PM CO2 Blowback BB Pistol might just be the best all around Airgun Makarov hitting all the hot spots us Replica Airgun enthusiasts love... Like full blowback operation, a nice light single action trigger, a full size metal magazine that holds the ammo and the CO2 and of course an all metal build with all those working bits and pieces like you would find on the real steel Makarov PM. But you will have to decide for yourself...
My Vimeo Video Review for the KWC Makarov PM CO2 Blowback BB Pistol:
Wow! Some new 4.5mm Steel BB and 6mm Plastic Airsoft guns and they are all brought to us from KWC. I would expect all of them to be available eventually in both 4.5mm Steel BB and 6mm Plastic Airsoft but for now I have the M11 in both Steel BB and Plastic Airsoft and the Makarov PM and CQBP M45 A1 in Steel BB.
This is just my quick preview video so make sure to watch it as I do show you around the guns fairly nicely but you can expect some more upcoming detailed Table Top and Shooting Videos shortly...
Here are some of the basic specifications for each gun...
