Trigger Pull: The trigger pull on the ASG Bersa BP9CC is light due to its true blowback operation that cocks the internal striker back with each shot taken. For some reason there is a slight creepiness in the trigger when the metal magazine is loaded, but it does not effect the lighter weight of the trigger pull. There is also a fair amount of take-up but the reset is short.
Accuracy: I shot the ASG Bersa BP9CC Blowback Airgun at a target from 20 feet away in a semi rested position, and it performed well getting a 2 inch grouping fairly centered on the target. The sights are non-adjustable, but for me there was no real need to adjust them. My initial Chrony testing puts this gun right in the 350 fps range.
Build Quality: ASG did another great job with the Bersa BP9CC, quality and build characteristics are very similar to my CZ 75 P-07 DUTY reviewed earlier. Everything that should be metal and polymer is the same on this as the original, and the fit and finish is very good in general!
Realism: The ASG Bersa BP9CC BB gun is as close as you can get to the real steel version while still retaining a good overall working airgun, the only real giveaway is the slightly longer but-plate on the magazine (most likely to allow for the CO2 screw tab). It looks very much like the real deal right down to the licensed Bersa trademarks and the 9x19 caliber markings on the slide and ejection port.
Good power and decent accuracy for a blowback gun with good usage of CO2.
Very well made, fit and finish is very good.
Very usable white dot sights.
All metal dropout magazine.
Gun feels great in the hand, love the thin profile.
Cons:
Magazine but plate is a bit on the long side, only telltale sign. also has strange moulding marks on it.
Trigger is a bit creepy when you have a loaded magazine and if you very slowly pull the trigger a BB can drop out of the barrel if holding downward.
Blowback is mild because of the lighter slide and reduced blowback movement.
Comments:
There are few smaller blowback air pistols that not only look great but perform well, this is one of them! I love the thin profile and overall operation of this pistol, for that very same reason the real steel version is doing exceptionally well here in North America which would make this airgun version a must have for any owners of the 9mm Bersa BP9CC. I highly recommend the ASG Bersa BP9CC 4.5mm BB Blowback Pistol to anyone looking for a very good quality and realistic BB pistol that does not compromise performance and build quality.
I am happy to report back to you on all the new cool stuff I got to see at this years 2013 SHOT Show in Las Vegas. Make sure to also watch my Vimeo video at the bottom of this post for some first person styled play by play of my experience at the Vegas SHOT Show 2013. (like you're there with me ;)
First up I want to cover a new gun from ASG, I have been wanting to get my hands on the 4.5mm Bersa BP9CC and I finally got to, not only did I get my hands on it but ASG was kind enough to supply me with one to take home for review. You can get the Bersa BP9CC in both Blowback and non-blowback versions and also in either BB or Airsoft. I opted for the 4.5mm BB Blowback version. I will be reviewing this BB gun very soon!
ASG also had a very cool prototype of an Airsoft CZ Scorpion EVO 3A1 hopefully coming out soon.
While roaming around SHOT Show 2013, I came across an interesting booth from FlashFog Security. I often get people asking me about using an airgun as a home defense weapon and I strongly advise against this. If the intruder is not scared off by the gun there is little an airgun can do to actually stop them. The FlashFog system works by rapidly filling a room with dense fog combined with a strobe light effect which blinds and disorients intruders completely. There is little an intruder can do other then try and get the heck out of there!
UPDATE: FlashFog just added a new section to their website specifically for School Security to help keep our schools safer from potential safety threats! So check it out: School Security Smoke Screen
I was a bit surprised by Gamo this year, they tend to stay away from actual Replica's and generally make BB/Pellet guns that look like popular guns but not any gun in particular. Gamo has a new BB/Pellet MP9 based machine pistol that uses a similar mechanism to their P-25 and PT-85 so it can shoot both 4.5mm BB's and .177 caliber Pellets using a double ended 16 shot rotary magazine. It also has an internal blowback system so it should have some recoil feel to it! I am pretty sure it is semi auto only but still a nice addition to their lineup!
Gamo also brought out a new 4.5mm BB Blowback pistol called the C-15 which has a metal slide and plastic frame, it kind of reminds me of the Umarex HPP in how it looks and feels.
Umarex had several new products that I am sure everyone is going to like! One that I think will do really well is the Steel Force, the Steel Force is designed around the 4.5mm BB shooting Steel Storm platform so it has a 6 round burst blowback operation and holds the 2x12 gram CO2 in the magazine while the BB's go in a 300 round hopper that feeds into a 30 round spring fed internal magazine. Like the Steel Storm it will shoot around 430 fps. The Steel Force has the advantage of being styled after the AR platform so it has a collapsible stock which will make shooting very easy.
Another often asked for airgun replica is the historic German Luger. This year Umarex stepped up to the plate and introduced the Umarex P.08 4.5mm BB pistol. Sorry, no blowback or even a working slide on this one but it is all metal and has a very good weight and feel to it.
If you're a fan of the entry level Umarex XBG then you may be interested in the new Umarex T.D.P. 45 which is very similar to the XBG in looks and features but with a slightly different look to it.
If you've ever wanted to turn your pistol into more of a PDW styled gun, you may be able to depending on which Umarex gun you have? Umarex added a very cool accessory called the T.A.C Converter that converts your Umarex HK USP (BB-Airsoft), SW MP40 (BB), XBG (BB), CZ Enforcer (Airsoft) and Walther P99 DOA (Airsoft) into more of a tactical (PDW) or Personal Defense Weapon complete with for-grip, adjustable rear sight, lots of rail options and a foldable stock.
I am assuming the Crosman M4-177 Pellet/BB Rifle has been doing well for Crosman as they have expanded with some more similar assault styled air rifles. The Crosman MSR77NP pretty much looks like a classic M16 but is in fact a Nitro Piston break barrel pellet rifle able to shoot .177 caliber pellets at 1200 fps (I hope there is a 499 fps Canada version planned too?).
A new takeoff of the M4-177 is the MK-177 which also shoots .177 caliber pellets and 4.5mm BB's using a multi-Pump System but it uses an upgraded more efficient pump system that squeaks out more fps with less pumps. The Crosman MK-177 is designed after the FN SCAR and is available in an adjustable iron sight version or a Red Dot equipped kit version.
One thing you can never get enough of in my opinion is another 1911 pistol! Crosman is introducing their GI Model 1911BB Blowback 4.5mm CO2 pistol, the one they had on hand was more of a prototype so the slide was not operational but it will feature an all metal design, blowback operation, 450 fps and a 20 round drop out magazine. I am sorry to say but it looks like the Crosman C51 has been dropped from Crosman's lineup but if you want a similar styled gun you can checkout the KWC SW40F which is a very close airsoft version.
We recently started carrying G&G Armament Airsoft guns, you can checkout my review of the Xtreme 45. I did stop by their booth and they had some new products on display, the M1 Grand (all wood stock) Airsoft had it's magwell all wrapped up as G&G had a propriety magazine system they did not want their competition to see. G&G also had some very interesting targets that light up, when shot they would react by individually turning off so you could see if you hit it or not.
There was a rather large crowd at the KWA booth but it was a shared booth so it's hard to say what everyone was looking at, the KWA area was pretty full, I did talk to the KWA rep and asked him point blank if KWC and KWA where the same or sister companies and the answer was not at all. There are often a lot of guns that look like they could be from the same company, I guess there is a lot of copying going on ;) One gun from KWA I would love to get my hands on is the Kriss SMG!
Now keep in mind many of these guns I have highlighted today are not available yet and a lot of them should be coming out in the spring time frame so please try to refrain from repeatedly asking when I will review them and have them in the store, it takes time and as much as we all want them now, they get here when they get here!
Watch my Vimeo video of the Replica Aiguns at SHOT Show Vegas 2013
I know I have been talking about this gun for some time now (Since last years SHOT Show) but the truth of the matter is Umarex did not release it all that quickly and when it did finally come out several months ago there was a recall and so the stock that came in quickly left again. So here we are now and I finally get to show everyone this very nice Umarex made Walther P38 BB shooting replica pistol.
At first glance it looks a lot like the Crosman C41, when I was at the 2012 SHOT Show visiting the Umarex booth, I thought they had just rebranded the Crosman's C41. When I took a closer look I could clearly see the difference and realism found in the Umarex Walther P38 version; like full Walther P38 licensing, blowback operation, working safety and slide catch. Pretty much everything that was missing from the Crosman C41. The Umarex P38 is a very accurate copy of a real steal P38 in almost every way.
All in all it looks to be another welcome and very realistic looking blowback BB Replica pistol and in this case one with a history that goes back to the way to World War II.
In our quest to bring you even more of the good stuff we are constantly adding to our Replica Airguns Store, we have recently added to our US Replica Airguns Store some more Blank Guns, Blank Gun Ammo and Blank Gun Magazines. We also added a new item, "Stock Badges".
I have talked about how KWC and Cybergun are really the same product and that Cybergun and KWC products in many cases are really the same gun but with some versions having slightly different markings on the guns themselves.
Today I show you a new 4.5mm Steel BB gun we just brought into the store very closely related to the Cybergun Tanfoglio Witness 1911, or otherwise known as the KWC Model 1911. This new airguns is a Tactical version of the Model M1911 and it goes by the name Model M1911 A1 Tac. It shares the same internal parts as the Tanfoglio Witness 1911 including the 4.5mm Steel BB magazine but the Tactical version is all black and has several updated modern parts that you would not find in a traditional 1911 A1 45 auto replica: Like the tactical trigger, hammer, adjustable white dot sights and accessory rial. This gun would make an awesome IPSC trainer for sure.
At this point there is no 6mm Airsoft version but you can get the KWC Model 1911 and M92 in 6mm Airsoft all metal versions.
I also compare my GSG 92 4.5mm Steel BB pistol I reviewed in the past and show you that it is identical to the KWC same M92 version with the exception of some marking on the slide. Many people even prefer the KWC branded models as they do not have the rather offensive white warning instructions all over them.
So if you're in the market for one of these super popular KWC/Cybergun blowback ultra realistic BB and Airsoft pistols you do have some options to consider...
Watch my Vimeo Video Preview for these very popular KWC/Cybergun Blowback Pistols:
In this part of the review I test the HK G36 KV AEG Rifle using my Chronograph to see what the 5 shot feet per second average is using fully charged batteries. I got pretty much right bang on to the factory claimed 450 fps using .20 gram 6mm plastic Airsoft BB's and consistency was within a few fps for each shot.
I also take the Umarex HK G36 KV AEG Blowback (EBB) Airsoft Rifle back 30 feet and shoot it at a target using a semi rested position (sand bag up front, standing in the back) and shoot in both semi auto and full auto, there really was no real difference in accuracy using both selections, I think the built in magnified scope helped out here to get a very tight 1.5 inch group shooting in semi and full auto.
So far out of all my AEG rifles I would have to say the Umarex HK G36 KV (EBB) performed the best getting very consistent and high fps and tight groupings in both semi and full auto even using light weight .20 gram BB's.
Watch my Field Test Shooting Vimeo Video Review for the Umarex HK G36 KV AEG Blowback Airsoft Rifle:
It would not be the end of another year without another Airgun, Airsoft Gun and Blank Gun Collection video for you. This year I'm not showing all my guns, I started to take them out and quickly realized there where just way too many and this years video would have been several hours long and would have taken most of the week for me to shoot and edit...
So this year I have hand picked some of my top favorites and most notable replica Airgun, Airsoft Gun and Blank Guns. They may not all be the best made or hardest shooters or even all that accurate but each one has some significants to me.
Trigger Pull: The trigger pull on the Umarex HK G36 KVis fairly short and light as it is essentially just an electrical on off switch for the internal electronic components. You can shoot the G36 very quickly in semi auto mode, and in full auto it cycles very quickly giving a high rate of fire.
Accuracy: In my brief pre-testing without any sighting in, the Umarex Heckler & Koch G36 KV shot just a bit off center to the right from a 30 foot semi rested position and produced a nice 2 inch grouping. In full auto the grouping opened up a bit but still punched a nice 1.5 inch hole in the target with most of the BB hitting there.
Build Quality: The Umarex HK G36 KV is very well made, yes it has lots of polymer but so does the real version and the plastic seems very durable, the fit and finish looked great and there is a lot of metal in and around the G36 where it would be on the real steel gun and where it is really required to be. Like the trigger, top rail, pins, selector switch, barrel, gearbox and gears.
Realism: Similar to my WE G39C reviewed earlier, I bet if you had a real Heckler & Koch G36 sitting beside the Umarex HK G36 KV, you would be hard pressed to tell them apart? The Umarex is also fully HK licensed and trademark throughout even including the 5.56mm NATO markings.
Excellent attention to detail with lots of working parts.
All metal internals and metal external mechanical parts.
Semi auto & full auto selectable.
Full HK licensing and markings.
Accurate 2 inch 10 shot group from 30 feet out.
Nice high 450+ FPS.
Full ambidextrous, even the charging handle can be switched side to side.
High capacity magazine (400 rounds)
Built in 3x optical sight with ability to add a Red Dot for close quarter shooting.
4 position adjustable folding stock.
Easy access to hop up system.
Cons:
Does not come with a battery or charger.
Came with the orange tip, you may want to replace it or paint it black?
May be too powerful for close quarter skirmishes without some detuning.
Comments:
This is my first Umarex Airsoft rifle product review and I have to say it really seems good so far, I have not had a lot of hands on time shooting the Umarex HK G36 KV but right out of the box I was getting very good results, nice high 450+ fps and good groupings even out at further range. The fit and finish are all very good and the realism is as good, if not better than other Airsoft AEG I have reviewed. I like the built in 3x Optical Scope and the addition of an upper rail to accommodate a Red Dot, this gives you the ability to acquire quick close up shot placements using a Red Dot while also being able to focus in on further out targets using the magnified optical scope. I look forward to my official Field Test shooting review.
This Update video addresses the similarities between the KWC and Cybergun product lines, specifically the KWC Model 1911 vs. the Cybergun Tanfoglio Witness 1911 and the KWC Taurus PT99 vs. the Cybergun GSG 92. In a nutshell, they are all made by KWC and are exactly the same with the exception of some of the licensing and branding that goes on the slides. Cybergun simply contracts KWC to make the guns for them and add some slight different printing. All parts are interchangeable.
I also show you the Silver Finish Blowback Airsoft KWC Desert Eagle and mention again that the licensing on this one is kind of hit and miss depending on what KWC sends us. So when you order one there is an additional surprise waiting for you when you open the box :)
Lastly, I show for the first time a G&G Airsoft product, the G&G Xtreme 45 Blowback that looks an awful lot like the Umarex Colt Special Combat chambered in 4.5mm Steel BB. The main differences are that the Colt Special Combat is a BB gun and the Xtreme 45 is an Airsoft gun. The G&G has blowback where as the Colt Special Combat does not have blowback.
Make sure to checkout my Vimeo video of this product update for even more info!
A bit of a heads up, one of our most poplar BB and Airsoft Pistols, the Dan Wesson line is for the most part fairly well stocked right now in the Canada Replica Airguns Store and ready for the Christmas rush! With that said don't hold off too long because we always run out of at least a few of the most popular versions...
Trigger Pull: The trigger pull on the Bolt Airsoft B4A1 is fairly short and light as it is essentially just an on off switch for the internal electronic components. You can shoot this gun very quickly in semi auto mode, and of course in full auto when full auto position is selected. As is with all AEG rifles there is a bit of a delay while the spring is retracted and released, this is not as noticeable in full auto.
Accuracy: I tested the B4A1 Airsoft rifle by putting around 10 rounds into a target from 30 feet with .36 gram Airsoft 6mm BB's while using a semi rested position (sand bag in the front - standing in the rear). I used a non-magnified red dot scope for this test rather than using the built in iron sights. I got very good result in semi auto and even with the recoil making my sights jump around a bit in full auto still stayed well centered on target and got about a 1.5 inch group in both semi and full auto. My chronograph testing with lighter .20 gram BB's resulted in a 421 fps 5 shot average.
Build Quality: The Bolt Airsoft B4A1 Metal AEG Carbine is very well made with a full Metal upper and lower receiver, along with metal and polymer parts exactly where they would be on the real steel version of an actual Colt M4. The only plastic or nylon components are the stocks and the grips and perhaps some internal parts. I found the adjustable stock and magazine tolerance to be tighter than my King Arms M4A1 I previously reviewed which showed the Bolt B4A1 had a bit higher quality in the workmanship, for the most part the fit and finish was very good!
Realism: As with many Airsoft guns, there is great attention to realism and the Bolt Airsoft BRSS B4A1 Carbine is another great example of an Airsoft Carbine based on the Colt M4 platform. It is an AEG but because of the BRSS (Bolt Recoil Shock System) you get a very nice compromise between a conventional AEG and a GBB (Gas Blow Back Airsoft) gun. In other words, like a standard AEG I get that endless stream of consistent BB's flying down range on target but unlike a true Gas Blow Back Airsoft gun, I don't get that drop off in power and limitation to about 30 usable rounds per magazine . What I do get similar to a GBB is that recoil action that helps make the shooting experience so much more believable! Even the sound from the Bolt B4A1 is much snapper than a standard AEG and more like a GBB. I also like the fact that the charging handle and forward assist work similarly to a real M4 and also the dust cover cleverly exposes the bolt and internal hop-up for easy adjustment along with the bolt cycling just like a GBB rifle would cycle which is similar to a real steel M4.
Great attention to detail with lots of working parts.
All Metal upper and lower receiver, lots of metal parts throughout.
Semi auto & full auto selectable.
High capacity 300+ round magazine.
Removable carry handle with Weaver/Picatinny rail underneath.
Nice high 420 real FPS.
Extremely accurate for plastic BB's.
Fully adjustable sights with two position Peep sights.
6 position adjustable stock.
Easy access to internal hop-up system.
Realistic Blowback Recoil system (BRSS) for a very believable shooting experience!
Cons:
May not get off as many shots per battery charge as a traditional AEG because of the Bolt Recoil Shock System.
Does not come with battery or charger but most higher end AEG's also do not.
Not yet readily available in Canada, maybe we can change that :)
Comments:
The Bolt Airsoft B4A1 Blowback Airsoft Carbine is a great compromise for the avid Airsofter looking for a practical skirmish weapon, but also craving the realistic experience of having blowback with recoil which up until now was really only provided by Gas Blow Back systems. I really like this concept and find it great fun to shoot even if its just for plinking in the yard. The overall quality is very good and you just have to love the M4 platform it's based on. If you're into customizing you can mix and match many external and internal parts with other existing Airsoft mechanical parts and I would imagine real steel accessories. I like mine as is with my addition of a riser and Red Dot and if I every get a chance to get out for a skirmish this will be my weapon of choice for sure!
I got a few sample products I wanted to quickly share with everyone :) First off Bolt Airsoft, a Taiwanese based company, sent me one of their B4A1 (M4A1 Copy) AEG Airsoft rifles featuring BRSS - (Bolt Recoil Shock System) which has Blowback with simulated recoil.
The Bolt B4A1 is designed after the M4A1 and looks and works like most AEG Airsoft rifles giving you sustained performance and the use of high capacity magazines but Bolt has added their BRSS - (Bolt Recoil Shock System) which gives you the feedback and recoil you would normally only get with a true GBB (Gas Blow Back) Airsoft gun.
I will be doing a full review very shortly so watch for it!
I also received from ASG (Action Sport Games) a few Mock Airsoft Suppressors, all of them are B&T (Brügger & Thomet) derivatives. It was nice that they sent me the version (MP9 QD) that fits perfectly on my ASG/KWA MP9. The other tow are the ROTEX-IIIA and ROTEX-IIIA Compact that fit perfectly on to a standard flash hider and even include one with them.
Check out my Vimeo Preview Video of these Review items from Bolt Airsoft and ASG:
I've had lots of requests to review the Daisy Winchester Model 11 and to give my opinion how it stacks up with the Cybergun Tanfoglio Witness 1911. I will be doing a full review of the Daisy Winchester Model 11 Colt 45 1911 replica shortly but wanted to kick things off with my comparison portion.
Your best off to simply watch my Vimeo Video Comparison of the Tanfoglio Witness 1911 and Winchester Model 11 but here are my thoughts on some of similarities, strengths and weaknesses for both 1911 syled airguns.
Similarities:
Both are good replicas of the classic Colt 45 1911 semi auto pistol.
Both shoot 4.5mm Steel BB's and use standard 12 gram CO2.
Both are mostly metal and weigh close to 2 pounds with the Cybergun Tanfoglio Witness weighing about 40 grams more.
Both come in a nice cardboard box.
Both have blowback operation with slides that lock back after the last shot.
Both have true 1911 styled single action only triggers.
Strengths:
The Winchester Model 11 has the higher feet per second rating and gets more shots per CO2 (410fps vs 320fps).
The Tanfoglio Witness 1911 has a full size drop out metal magazine that holds the BB's and CO2.
The Winchester Model 11 is more economical to buy and shoot.
The Tanfoglio Witness 1911 has a more realistic "full" blowback operation.
The Winchester Model 11 has less intrusive warning markings on the slide.
The Tanfoglio Witness 1911 has a working Grip Safety.
The Winchester Model 11 is made in Japan.
The Tanfoglio Witness 1911 can be field stripped similar to a real 1911.
Both have fairly high capacity magazines (16 BB's for the Winchester and 18 BB's for the Tanfoglio).
Weaknesses:
The Winchester Model 11 has a funky extra button on the thumb safety?
The Tanfoglio Witness 1911 tends to use a lot of CO2 with less average fps.
The Winchester Model 11 has more free-play (wiggle) in the slide.
The Tanfoglio Witness 1911 magazine are more expensive and can be hard to find at times.
All in all I really like both guns, and what really counts is how they feel and shoot and after a quick outside testing with the Daisy Winchester Model 11, it seemed to shoot and work pretty good for me. Realists may prefer the Cybergun Tanfoglio Witness 1911 because it is more realistic in terms of how it's built and how it functions but as a daily shooting gun, the Daisy Winchester Model 11 hits harder and gets more shots per CO2, all while still giving the shooter a very realistic 1911 styled shooting experience.
Watch my Vimeo video Comparison of the Daisy Winchester Model 11 vs the Cybergun Tanfoglio Witness 1911:
Trigger Pull: The trigger pull on the ASG/KWC MP9 A3 is single action only as the charging handle has to be pulled back to open and release the bolt for the first shot. There is a trigger safety but it is not noticeable when shooting this Airsoft machine gun. There is a short take-up and then a light release and short reset.
Accuracy: Right away I put my NcSTAR 1x25 Red Dot sight on the ASG/KWC MP9 A3 as it was a perfect fit for this small and compact machine pistol, it did not take long to sight it in and I was able to get decent accuracy in both semi auto and full auto burst due to the mild but very fast cycle rate. I was able to get a 2 inch grouping at 30 feet out using a rested position. In full auto mode the grouping did not really get too much wider. I also got between 350 and 370 fps when testing the ASG MP9 on my Chronograph.
Build Quality: The ASG/KWC MP9 A3 Airsoft Machine Pistol is built very well, using similar components that you would find on the real steel version so yes it has a plastic shell but that is to be expected. The ASG/KWC MP9 A3 does use lots of metal where it needs to be like in the internal parts, pins, bolt, barrel, rails and even the magazine. The fit and finish is near perfect!
Realism: I have to say the ASG/KWC MP9 A3 is pretty much a bang on copy of the real steel Brügger & Thomet MP9 A3. The only telltale sign is the ASG branding on the right side along with the 6mm caliber beside the ASG logo. One other small detail is the magazine which is metal on the Airsoft version where as you would find the real version uses a transparent polymer magazine.
Rate of fire is very fast and does not slow down much even when the gas is running low.
Good overall power for a short barreled gas blowback gun.
Very nice trigger with working trigger safety.
Excellent replica of the real steel version in just about every way.
Can add a lot of gear and make this gun your own.
Decent price for all you get out of the ASG MP9!
Cons:
Bolt didn't lock back for me when the gun got really cold?
Real magazine would actually be transparent polymer.
Comments:
I really like the ASG/KWC MP9 A3! I love the look, I love the features and the price is also really good for what you are getting. I was really impressed with the super high cycle rate and because of the small low weight bolt the gun does not move around too much or slow down in rounds per minute even when you do a full mag dump. There is however just enough blowback recoil to give you that GBB realistic feel! I also found that the magazine holds a lot of gas so it is possible to get two magazine worth of shots out of a single fill, that's around 100 shots. I also like how easy it is to add to the ASG/KWC MP9 A3, I had mine pimped out and looking amazing right away and suggest if you get one you do the same :)
My Vimeo Video of the ASG/KWC MP9 A3 Airsoft Machine Pistol:
For my Canadian Blank Gun collectors, I'm not going to list these ones as Silent Auction items this time around so if you're looking for an EKOL blank gun, I have one of each of the following versions for sale:
This one has to be the coolest Machine Pistols out there!
The KWA (ASG) B&T MP9 A3 Black GBB is a compact gas blowback machine pistol licensed by the original manufacturer Brügger & Thomet, Switzerland. The A3 version has a bottom rail and a folding stock and the whole body is made of reinforced fiber polymer. The whole construction of the MP9 is very realistic and it is field stripped as the real thing. The cocking handle is functional with the realistic metal bolt. The B&T MP9 has adjustable hop-up and both semi and full auto firing mode can be selected. Furthermore the trigger has an active safety function.
Plastic 6mm Airsoft BB's
(GBB) Gas Blow Back
Semi & Full Auto
366+ fps w/ .2g
Adjustable Hop Up
3.9 lbs
48 Round Magazine
11.5 Inches Folded - 20.5 Inches Open
Reinforced Fiber Polymer Body
Field Strips like the Real Steel
NO CLEAR sections (All Black) and does NOT have orange tip!
Take aim and fire with "The gun that helped to change the world". The Thompson Military M1A1 AEG is a battlefield weapon with a serious attitude. This beautiful gun is a fully licensed 1:1 scale replica of a real Tommy gun, and features a full metal body with artificial wood grain finish, a 60 Rd plastic magazine, and a shot velocity of 500 fps (using .20g BBs). The M1A1 also features an adjustable BAXS System for increased power and shooting accuracy. Airsoft enthusiasts will love the stunning classic era looks and awesome semi/fully automatic firepower of the Thompson Military M1A1 AEG. Do not miss this gun! Recommended for use with high quality .25g BBs.
Trigger Pull: The trigger pull on the WE G39C is about what you would expect from a Single action only Semi Auto rifle, it has a very slight take up and then about a 4 pound trigger pull that is crisp and smooth.
Accuracy: Out of the Box the WE G39C shot great up close and farther out, the hop-up seemed to be already dialed in, and even though I was using only .20 gram BB's which is a bit light for this gun, I still found they tracked well and stayed on target both near and far. My 30 foot semi rested testing produced a nice 2 inch grouping. Shooting the barrel out on the tactical range I did have to aim just a bit higher when back out at 60 or more feet away. Maybe a slight bit more hop-up would do the trick.
Build Quality: The WE G39C is very well made, yes it has lots of polymer but so does the real version and the plastic seems very durable, The fit and finish looked great and there is a lot of metal in and around the G39C where it would be on the real steel gun and where it is really required to be. Like the trigger, flash hider, rails, pins, switches, rear sight, magazine and most internal parts also.
Realism: I bet if you had the real G36C sitting beside the WE G39C you would be hard pressed to tell them apart? WE did a great job making this Airsoft version very believable not just in appearance but also when field stripping it and shooting it with it's heavy bolt and felt blowback recoil.
Amazing attention to detail, just like the real H&K G36C.
All metal internals and metal external mechanical parts.
Semi auto & full auto selectable.
Awesome blowback kick really hits you in the shoulder.
Field strips just like the real steal version.
Nice high 400 FPS and good accuracy near and far.
Full ambidextrous, even the charging handle can be switched side to side.
Can get up to three magazines per propane fill up.
Very well priced for how awesome it really is.
Cons:
Some people may not like that it is a polymer built gun externally but it is what it is!
And that's it!
Comments:
So far I have been impressed with We an Airsoft company, they really know how to make very realistic and high quality products. I wasn't sure if I was going to like the mostly polymer external build on this gun but the sheer quality and solid build took away any ideas that tis Airsoft gun would be anything like a toy. The WE G39C is one of the best performing GBB Airsoft guns I have tried out getting up to 90 shots per gas fill on a magazine which is very impressive. We was also able to keep the price down which means more people can get into one of the G39C's. If you've been thinking about adding one of these to your arsenal I don't see any reason why not to!
I recently picked up a couple of really nice condition pre-owned Air pistols, both replicas of some IWI (Israel Weapon Industries) semi auto pistols. The biggest and baddest being a very authentic replica of the notorious Desert Eagle. This Umarex CO2 Airgun Desert Eagle shoots .177 caliber pellets using an 8 shot rotary magazine and has realistic blowback action with over 400 fps velocity. It has excellent accuracy and packs a real punch.
I also have my Cybergun Jericho 941 which again is a very believable replica of the real steel semi auto pistol, some people refer to it as the Baby Eagle. The 4.5mm BB version has a full metal slide and full size drop out metal magazine that holds the BB's and CO2.
Both guns are in like-new condition and come with the original boxes and manuals, the Desert Eagle even comes with three magazines.
To get in on the bidding, simply Email Me Here with your highest bid by no later than October 10th 2012 at midnight. At the conclusion of this Silent Auction I will notify the winner.
This Airgun Silent Auction is open to both my Canada and US customers, Canadian Customers will pay an additional $17.99 for Shipping/Handling plus their local provincial sales Tax. US Customers will pay $29.99 International Canada to US Shipping & Handling but will not pay any sales tax. Good luck to everyone!
Checkout my related links for both of these very nice air pistols:
For all those people who keep emailing asking me to sell my prized Russian made Nickel Baikal MP-654K CO2 BB Pistol, now is your chance. No I'm not selling mine but I managed to acquire another exact same version, both are made in 2004 and are very closely made in production based on their serial numbers. To be honest the new one I just received is actually a bit nicer than mine, the polishing work on the Nickel is nicer! Perhaps I have grown attached to mine and it has sentimental value so I am keeping mine even though perhaps it is not as nice as the one up for action.
Either way, some lucky person is going to own a very rare Nickel Baikal Makarov MP-654K BB pistol very shortly!
To get in on the bidding, simply Email Me Here with your highest bid by no later than September 26th at midnight. At the conclusion of this Silent Auction I will notify the winner.
This Airgun Silent Auction is open to both my Canada and US customers, Canadian Customers will pay an additional $17.99 for Shipping/Handling plus their local provincial sales Tax. US Customers will pay $29.99 International Canada to US Shipping & Handling but will not pay any sales tax. Good luck to everyone!
Below are some photos for you to drool over of the actual Nickel Makarov MP-654K up for bis and also make sure to watch all my video on this very fine and rare BB pistol.
