Umarex has released yet another Legends Replica Airgun and perhaps this one may be the most iconic yet, the M3 Grease gun with a history as far back as 1942. It was put into service int 1944 and then the later variant the M3A1 was used in the Korean War. Also make sure to watch my Table top Video for it for specifications and details along with more close up video.
Getting back to the Field Test Review for the Umarex Legends CO2 Blowback Full Auto M3 Grease Gun, as always I like to test each gun out in the Replace Airguns Indoor Sea Can Airguns Range first placing 5 rounds through my Chronograph to find out the real world velocity of each test gun, then I shoot 10 rounds in semi auto at a distance of 30 feet onto a paper target to see how tight of a grouping I can get shooting from a seated and rested position. With full auto Airguns I like to then perform a full auto shooting test to see how it groups in full auto as often times the full auto grouping will open up somewhat as some Blowback Full Auto Airguns do tend to move around a lot more in full auto mode.
For my Power or Velocity test I was using dual brand new CO2 cartages. Umarex does state that the Umarex Legends CO2 Blowback Full Auto M3 Grease Gun will shoot around 450 fps and with my 5 shot test I was able to confirm this and get close to this mark averaging 436fps. The temperature in the Sea Can was around 20 degrees Celsius or around 70 degrees Fahrenheit. Perhaps in warmer conditions I might hit the claimed 450 fps but I was close either way.
For my accuracy test I setup a new paper target 30 feet downrange and proceeded to place 10 shots into it using the peep sight on the Umarex Legends CO2 Blowback Full Auto M3 Grease Gun. I was fairly pleased with a fairly tight 1.5 inch grouping in semi auto. I then switched over to full auto fun mode and with the remaining BB’s I unloaded 50 or so rounds in very short order and as expected the grouping opened up to closer to a 4 inch grouping. This was kind of expected since the Umarex Legends CO2 Blowback Full Auto M3 Grease Gun uses an open bolt system which has a fairly heavy bolt which makes the blowback action more intense, similar to the KWC Mini Uzi but to a lessor degree.
Any time a company puts out another Full Auto Replica Rifle, especially full auto firing, I am 100% in on it. Both Crosman and Umarex have done a great job doing this and the Umarex Legends CO2 Blowback Full Auto M3 Grease Gun is another example of a well thought out and what I expect to be very popular Full Auto BB Rifle. Their Legends series encompasses guns of the later era which I personally really like since they are harder to come by in their real steel versions, so having them available in an easier to acquire version that you can even shoot in your back yard is a win win for everyone. I am also happy to confirm the high capacity double stack 60 round magazine seemed to feed pretty good for me only miss-feeding once during my testing while doing the Chronograph portion but it got back on track right away. If you’re into Full Auto Legendary Airguns then for sure pick one up from us!
Type:BB Rifle. Manufacturer: Umarex. Model: Legends M3 Grease Gun Materials: Mostly All Metal Construction. Weight: 7.7 pounds (3.5 kilograms). Length: 29.8 inches (757mm). Barrel Length: 8 inches (20 cm) smoothbore barrel. Propulsion: Dual CO2 Cartridge. Action: Semi & Full Auto Open Bolt Blowback Ammunition Type: 4.5mm steel BB's. Ammunition Capacity: 60 rounds. FPS: 460fps. Rate of Fire: 1050
Trigger Pull: The trigger pull on the Umarex Legends M3 Grease Gun is fairly light being a single action only trigger. You will have to open the bolt (pull it to the rear) which is located under the dust cover using your thumb but the recoil spring is not super heavy on the Airgun version. I would imagine this would take more effort on the real steel version.
Accuracy: I have not Field Test Reviewed the CO2 BB Full Auto Umarex Legends M3 Grease Gun as of yet but will be making a full Fields Test Review next week to find out what to expect in terms of accuracy on both semi and full auto modes along with velocity using brand new twin CO2 Cartridges.
Build Quality: The Umarex Legends BB Grease Gun is really made with form what I can see is an all metal construction at least on the outside. The fit and finishes feel and look really good and it has a nice balance and weight to it.
Realism: The Umarex Legends BB Firing M3 Grease Gun is based on the actual M3A1 version and looks just like it including the rough welds and simple build. Even the action is Open Bolt which means you have to pull the bolt back using your thumb or finger, then when you release the trigger the bolt moves forward loading a round in the chamber and then acting like the firing pin and firing the gun which in turn uses the pressure to cycle the bolt into the rear position ready to fire the next shot in either semi or full auto mode.
Pros:
Yet another Classic Legends Replica Airgun from Umarex.
Virtually all metal design with good overall weight.
Price is very reasonable for all metal replica machine gun in an all metal construction.
Semi and Full auto select-ability.
Dual CO2 design for increased shots and less cool down effect.
Super high capacity 60 round full size drop out metal magazine. (hopefully it works well)
Great looking replica of the real steel Grease Gun in looks, operation and feel.
Internal bolt blowback will give a bit of recoil feedback feel.
Uses a genuine open bolt system.
Recessed barrel for added realism.
Cons:
Sights are non-adjustable.
Hopefully high capacity magazine feeds consistently?
Selector switch under frame is not authentic but does allow for semi, full auto and safe modes.
Comments:
The Umarex Legends M3 Grease Gun is yet another great addition to not only the Legends Series of Umarex Airguns but also their Full Auto BB Rifle lineup! I am hoping the 60 round magazine feeds properly as double\ stack 4.5mm BB Rounds don’t always feed as well as Airsoft BB’s do. I guess we will find out when I make my Filed Test Shooting Video… That said the M3 Grease Gun is an excellent Replica of the real steel version with an all metal build and even a true to form open bolt blowback system. I really hope it performs well so I can recommend this Airgun, on first impressions and simply holding and looking around this BB Machine gun I am impressed so far.
My Table Top Video of the Umarex Legends Full Auto M3 Grease Gun:
In this Preview Unboxing Video I take a look at three new products just listed in our Replica Airguns Store. Two are products from Umarex both being CO2 4.5mm Steel BB and one is a CO2 powered KWC Blowback Airsoft Pistol. I don’t go into a ton of detail in this video but go over what is listed on the box and a quick walk around of each product.
First up I show off the KWC DE L6 CO2 Blowback Airsoft Pistol, it is much like the Cybergun Desert Eagle L6 I reviewed but without the orange tip and with notched pistol grips, also all back which is classic and looks great. This Blowback pistol shoots 6mm Airsoft BB’s at around 360 fps and has a full size dropout metal magazine that holds the CO2 along with 21 rounds.
Next I showcase a rather entry level 4.5mm CO2 BB Pump Action Rifle called the Umarex NXG Pump Shot that is a mostly plastic lighter weight build perfect for smaller or younger shooters. It uses CO2, shoots 4.5mm Steel BB’s and comes with a drop out 10 round rotary magazine. You will have to pump it before each shot but this makes the trigger fairly light.
Lastly but perhaps my favorite in this lineup I take a look at the CO2 4.5mm Blowback Umarex Legends M3 Grease Gun. Just like the real steel .45 caliber Grease Gun it is capable of full auto and also shoots in semi auto. You will find a full size drop out metal magazine that holds two CO2 cartridges along with 60 4.5mm steel BB’s. Thats a lot of rounds!
If you are wondering why I am doing another Field Test of a Crosman AR-15 type CO2 Full Auto BB Rifle… Well why not, any excuse to play around with one of these and I will take it. You never know, even though the Crosman R1 Fallen Patriots Blowback CO2 Full Auto BB Rifle is essentially just a re-skinned R1, what if it performs better or worse than the standard R1. I better test it out and find out for myself.
Like all my other Field Test Shooting Videos I test out the Velocity and Accuracy in the Replica Airguns Indoors Sea Can Shooting Range where I can control the temperature, wind and lighting conditions. The goal is to see if the velocity is what the manufacturer claims and what kind of groupings I can get in this case shooting 10 rounds in semi auto and the rest in full auto.
Starting with my velocity test for the Crosman R1 Fallen Patriots Blowback CO2 Full Auto BB Rifle I shot five 4.5mm Steel BB’s through my Chronograph and was able to average 389 fps. Crosman claims a max fps of 430 which would be best case scenario in what would most likely be fairly warm shooting conditions. During my testing the temperature was not overly warm or cool, right around room temperature so around 20 degrees Celsius (70 ish degrees Fahrenheit) and I was using dual brand new CO2 Cartridges.
Next I tested out the accuracy for the Crosman R1 Fallen Patriots Blowback CO2 Full Auto BB Rifle first shooting 10 rounds in semi auto and then dumping the rest of the magazine in full auto. Right out of the box using the iron pop-up sights I was able to get all but 1 shot in the Bulls-eye which is about 1 inch in diameter so not only is the Crosman R1 Fallen Patriots Blowback CO2 Full Auto BB Rifle very accurate but it was really well centered out of the box in my case. Switching over to full auto the grouping spread out as expected more to around 2+ inches and placing a bit lower on the target but this is expected when shooting a blowback Airgun in full auto as it will move around a bit.
I do have to say the Crosman R1 Fallen Patriots Blowback CO2 Full Auto BB Rifle is probably one of the best looking AR’s in the Crosman series of Full Auto BB Rifles and I am happy to report the performance was as expected since I have done several Field Test Shooting Reviews for this series of BB Rifles. No you do not get a red dot with the Crosman R1 Fallen Patriots Blowback CO2 Full Auto BB Rifle but rather more old school iron sights but it really suits this BB Machine Gun and for me it didn’t hurt performance at all!
In this Field Test Shooting Video I test out the BARRA 400e Full Auto AEG 4.5mm BB Rifle to test out the velocity along with the accuracy and also get an idea on what the rate of fire is in Full Auto mode as on the box it claims 550 rounds per minute using what I would assume is a 7.4 volt battery. I wanted to test the BARRA 400e using an 11.1 volt battery but mine died on me. I will more than likely make a short video where I test out the 11.1 volt battery to see how this effects the rate of fire. If you want more information on specifications and details for the BARRA 400e then check my Table Table Video for it here.
Starting with testing out the Velocity for the BARRA 400e Full Auto AEG 4.5mm BB Rifle I shoot 6 rounds through my Chronograph to average out the fps and I was able to average 385 fps which is fairly close to the claimed 410 fps. Temperature does not effect an AEG as no CO2 is being used. Battery voltage also does not effect velocity as long as there is enough voltage to make the AEG motor pull the spring all the way back. Only trigger delay and rounds per minute are effected by battery voltage.
Moving on to my accuracy findings, I loaded up a full 50 round magazine and first unloaded 10 rounds fairly quickly into my paper target setup 30 feet down range shooting from a seated shooting position with the BARRA 400e resting on a sand bag up front. I was impressed to get close to a 1 inch 10 round grouping that placed just a little to the left and down from the bullseye right out of the box. I could easily center the sights as they are fully adjustable. I then switched the BARRA 400e Full Auto AEG 4.5mm BB Rifle to full auto and shot the remaining 40 or so rounds into the same paper target and even though the grouping opened up a little bit, it was not by much so accuracy in semi and full auto is very good with the BARRA 400e.
I have to say the rate of fire on the BARRA 400e Full Auto AEG 4.5mm BB Rifle using a 7.4 volt battery is rather slow even compared to other Airsoft AEG Full Auto Airguns but I still yet have to test it out using a brand new 11.1 volt Lithium battery so I do expect the rate of fire to improve a noticeable amount. Stay posted for that update video. Even with the slower rate of fire from the BARRA 400e this gun is awesome, it is really accurate and the velocity stays super consistent since CO2 cool down is not a factor. The mostly all metal construction and overall quality is very good and the fact that this is really the first commercial AEG 4.5mm Steel BB Rifle makes that alone a great reason to pick one up.
Type:BB Rifle. Manufacturer: BARRA. Model: BARRA 400e. Materials: Mostly Metal with some plastic. Weight: 7.5 pounds (3.4 kilograms). Length: 42.25 inches (1073mm). Propulsion: AEG (with Deans Connectors). Action: Semi & Full Auto. Ammunition Type: 4.5mm steel BB's. Ammunition Capacity: 50 rounds. (1000 shots per battery charge Aprox.) FPS: 410fps. Rate of Fire: 550+ rounds per minute in full auto (depending on battery voltage).
Trigger Pull: The trigger pull on the BARRA 400e AEG Full Auto BB Rifle like other AEG Rifles is not mechanical per say as it is essentially electrical driven so basically it is an on off switch that is closest in feel to a single action only trigger since it is light and short. You will notice a slight delay between pressing the trigger and the actual round being fired since the trigger activates a motor which first pulls the air spring back, once the spring is fully drawn back it releases and compresses the air which then propelled the 4.5mm steel BB. The higher voltage battery you use will shorten the delay as the motor will spin faster and pull back the spring quicker allowing for less noticeable delay and also a higher rate of full auto fire.
Accuracy: I have not Field Test Reviewed the BARRA 400e AEG Full Auto BB Rifle or even tried it out yet as it does not come with a battery or charger and as it uses a Deans connector I will need to get a battery that not only fits this gun size-wise but also has a Deans connector on it. Once I have this battery I will be able to make my Field Test Shooting Video for it. It should have a very consistent velocity since there is no CO2 cool down to factor in so each shot when I Chronograph it should be very similar in fps. I also expect accuracy to be decent since there will not be a lot of recoil as there is no blowback action here.
Build Quality: The BARRA 400e AEG Full Auto BB Rifle is almost all metal in design with an actual CNC machined aluminum hand guard and reciever! It feels very solid when holding it and the fit and finishes are really good. The only plastic I noticed on this AEG styled BB Rifle are the rear stock, pistol grip, and pop-up sights, everything else as far as I can tell are made out of metals.
Realism: The BARRA 400e AEG Full Auto BB Rifle is based on the AR platform in terms of its overall design and looks like a sub variant for sure. It is missing the default forward assist but in all the AIrgun versions of AR typo rifles the forward assist is just for show since there is nothing to assist with an Airgun. Most mechanical parts work as you would expect like the charging handle, magazine release, sectors switch, dust cover and of course the trigger.
Pros:
No CO2 required so cost to shoot is less.
Very consistent velocity as there is no cool down effect from CO2 cooling the gun.
Have the option to shoot in semi or full auto modes.
Almost all metal construction, very solid feeling gun.
Lots of rail option for mounting accessories (Picatinny on the top and M-LOK on sides and bottom).
Flip up sights use a dual mode, when not flipped up you have finer optic lower profile sights, when up there is a post in the front and peep in the back.
6 position adjustable rear stock.
Nice high capacity 50 round magazine, will need more mags for sure since you get 1000 shots per battery charge.
Comes with a speed loader too.
Lots of working parts including the charging handle, dust cover, magazine release, selector switch.
Selector switch is ambidextrous.
Cons:
No blowback operation as with some other Full Auto BB Rifles like the Crosman AR Series.
Does not come with a battery or charger, will need ones that fit and use a Deans connectors.
No red dot included with this version but the iron sights are well thought out.
Comments:
The BARRA 400e AEG Full Auto BB Rifle is something new to the Airgun industry and I always like it when a company doesn’t just make their own version of something we already have in the market and basically just put their branding and licensing on all the same guns. BARRA has made what I believe to be the first AEG 4.5mm Steel BB rifle at least one that has come to market and I always wondered why nobody has tried this before? Well here it is and now we get to see how well an AEG performs with 4.5mm Steel BB’s! Maybe this will start a new market of AEG type 4.5mm Steel BB Guns? I say if it works, well then go for it.
My Table Top Video of the BARRA 400e AEG Full Auto BB Rifle:
Type: BB Rifle. Manufacturer: Crosman. Model: R1 Fallen Patriots AR. Materials: Metal & plastic. Weight: 6 pounds (2.7 kilograms). Length: 26.25 / 29.25 inches (Stock closed / extended). Propulsion: 12 gram CO2 dual cartridges. Action: Semi & Full AutoBlowback - single action only. Ammunition Type: 4.5mm steel BB's. Ammunition Capacity: 25 rounds. FPS: 430fps. Rate of Fire: 1400 rounds per minute in full auto.
Trigger Pull: The trigger pull on the Crosman R1 Fallen Patriots Blowback CO2 Full Auto BB Rifle is single action only since the charging handle must be pulled back first before you can shoot it. The trigger is short and fairly light as you would expect from an AR type trigger action. The real fun happens with the Crosman R1 Fallen Patriots Blowback CO2 Full Auto BB Rifle when you switch it over to full auto mode and with just one pull and hold of the trigger you empty the 25 round magazine in mere seconds.
Accuracy: I have not Filed Test Reviewed the Fallen Patriot version of the R1 just yet but you checkout my Filed Test Shooting Video for the Crosman R1 Regular Version where I test out it using my Chronograph and I get an average of 385 fps and a nice 30 foot grouping of right around 1 inch in semi out and a decently tight full auto group of about 3-4 inches.
Build Quality: The Crosman R1 Fallen Patriots Blowback CO2 Full Auto BB Rifle as with all the Crosman AR type BB Machine Guns is well made all around. Weighing in at 6 pounds without any add on accessories it feels solid and well built. There is a lot of metal going on inside and out of this rifle but keep in mind the top and bottom receiver are plastic with metal parts where they need to be like in the internals, pretty much all the working parts are metal, the magazine is full metal, the buffer tub is metal, charging handle, selector switch, magazine release, bolt release, trigger and of course the barrel is metal.
Realism: The Crosman R1 Fallen Patriots Blowback CO2 Full Auto BB Rifle is about as real as you are going to find in a CO2 Blowback AR/M4 styled Airgun. You can even take it apart and split the top and bottom receivers like the real steal version. The blowback action gives you some recoil but more importantly offers a true single action trigger and of course the full auto ability we all want and love. Almost all the working parts work like they would on a real AR/M4 other than the forward assist which is moulded into the receiver.
Pros:
Color scheme is awesome looking.
Super realistic working M4/AR 4.5mm BB Rifle just like the otters Crosman Rifles in this lineup.
Full blowback operation with both semi and full auto shooting, can feel the blowback operation rocking the gun.
Great weight and feel to it.
Almost everything works exactly like the real steel version. (Charging handle, dust cover, bolt release, magazine release, selector switch…)
Duel CO2 full metal drop out magazine that holds the 25 4.5mm steel BB’s as well.
Adjustable and customizable AR butt stock.
Included iron pop-up sights you can add a red dot sight on rail if you want to but looks classic without it..
Lots of rails for mounting additional cool hardware.
Removable flash hider that uses standard threading.
Cons:
Receiver is plastic but well made and does not compromise feel or weight since there is lots of metal throughout this gun.
No red dot included with this version.
Comments:
The Crosman R1 Fallen Patriots Blowback CO2 Full Auto BB Rifle is really pretty much the same as the Standard Version Crosman R1 with really only cosmetic color scheme changes. That said these cosmetic changes make it look awesome and in my books this is the nicest looking Crosman AR Series Full Auto BB Gun so far. I even like the fact that it comes with Iron Sights over a Red Dot. Typically I prefer a Red Dot as I find them easier to shoot with but on this version the iron sights really suit it and give it a more classic AR look to it. If you want you can easily add a Red Dot sight so do what every makes you happy.
My Table Top Video of the Crosman R1 Fallen Patriots CO2 Blowback BB Machine Gun:
In this Preview Unboxing Video I take a look at two full auto BB Machine guns but both very different and both from two separate companies. One is traditionally CO2 operated and the other is AEG operated which is a very new concept for a 4.5mm Steel BB Airgun. I have always wondered why nobody had attempted an AEG 4.5mm Steel BB gun before so here we have the first one to be released…
Starting with the Crosman R1 Fallen Patriots Full Auto CO2 BB Rifle it is essential a re-skinned R1 with a very unique coloration and of course the Fallen Patriots markings on it. The main receiver is a gun metal grey with black and red accents throughout and a purple-blue magazine. It really is stunning to look at and perhaps my favorite Crosman AR series Full Auto BB Gun to date. You do get pop-up Iron sights rather than a red dot which I feel suits this Airgun best and everything else in terms of specifications will be the same as the R1 so check that rifle out for more info.
Now the BARRA 400e is really something new to Steel BB Guns, basically it steals the AEG (Automatic Electric Gun) from what is typically reserved for Airsoft Rifles. I have always wondered why this technology has never been transferred over to 4.5mm Steel BB Airguns? Well now it has with the BARRA 400e Full Auto AEG BB Rifle. According to BARRA you can export to get around 410 fps and that should be super consistent since there is no CO2 cool down effect. You can also shoot in semi or full auto and it has a 50 round magazine that comes with a speed loader for easy loading. Another point to mention is that the BARRA 400e is almost all metal and feels really solid.
In this Field Test Shooting Video I test out the Umarex T4E HDX .68 Paintball Shotgun to find out what the actual fps is and if .68 Caliber Rubber Balls shot out of this Paintball gun are even going to be somewhat accurate at 30 feet out? If you have not already watched my Table Top Video where I go over the details and specifications with some closer up video showing you around the Umarex T4E HDX .68 Paintball Shotgun then make sure to watch it here…
Starting with the velocity portion of this video I used .68 caliber rubber balls which are not super heavy and not made out of a very hard rubber as you can squish them with your fingers fairly easily. I put 5 rounds through my chronograph after loading a pair of 12 gram CO2 cartriges into the CO2 chamber. My results averaged 206 fps which may seem slower than expected but they did hit my target pretty hard and actually knocked the cardboard backing right off of it. Each round was fairly consistent ranging from 203 to 210 fps.
Moving on to the accuracy portion of this test I proceeded to shoot around 10 rounds into my fresh paper target setup 30 feet down range. My target is basically an 8.5 x 11 sheet of paper and my goal was ot get all my shots onto the paper which I managed successfully. I would say most of the rounds all hit within about 5-6 inches of each other which for a Paintball Gun is very good! Keep in mind I was shooting using a seated position with the Umarex T4E HDX .68 Paintball Shotgun rested up front on a sand bag.
All in all the Umarex T4E HDX .68 Paintball Shotgun performed really well shooting consistent velocities and also getting all the rounds on an 8.5 x 11 inch target easily at 30 feet away which means if you where shooting at a persons body area you would easily hit it every shot making this a decent close quarters shooter which is what it really would be used for at the end of the day. Could you use it for less lethal home defense? I guess so especially if you can get your hands on pepper balls but I am not sure if regular rubber or paintballs balls would stop someone? Just seeing this impressive shotgun may in fact be more of a deterrent then being shot by it, but if it get’s the job done then why not.
In this Field test Shooting Video I Test out the Specna Arms Core SA-C07-PDW AEG Airsoft Rifle in the Replica Airguns Indoor Airgun Shooting Range to find out what kind of velocity we can achieve using standard .20 gram Plastic Airsoft BB’s. I also shoot 10 rounds in semi auto at my paper target 30 feet down range to see what kind of grouping I can get and then switch it over to full auto and let her rip till I am basically out of ammo and see if I can punch a nice hole in my cardboard backed target. If you are looking for more details and specification along with some closer up video then make sure to watch my Table Top Review Video for the Specna Arms Core SA-C07-PDW AEG Airsoft Rifle.
Starting with my velocity test, I shot 5 rounds through my Chronograph using .20 gram Plastic Airsoft BB’s with the preinstalled spring and got an average of 402 fps with my lowest velocity being 400 and my highest velocity being 405 so really close in fps. You can tone down the Specna Arms Core SA-C07-PDW AEG Airsoft Rifle a bit b y installing the M90 Spring if you find the fps to be a bit high for close quarter battles.
For the accuracy portion of this Field Test Shooting Review I proceeded to fire 10 semi auto rounds into a paper target setup 30 feet away. I use a semi rested shooting position with the Specna Arms Core SA-C07-PDW AEG Airsoft Rifle resting on a sand bag up front and me sitting on a stool for stability. My 10 shot grouping was all within around 1 to 1.5 inches which is very good for an Airsoft Rifle shooting lighter Plastic BB’s. I then switched the selector into “fun mode” (Full Auto) and proceeded to hold the trigger down until I ran out of spring tension on the High Cap Magazine. I would say I got through around 100+ rounds with most of them making about a 2 inch hole in my target consisting of cardboard and of course the paper target in front of it.
I have reviewed the Specula Arms line of Airsoft Rifles in the past, both the Core and the Edge and they really are great Airsoft Guns. The Specna Arms Core SA-C07-PDW AEG Airsoft Rifle as expected lived up to my expectations and performed really great in this Field Test Shooting Video. If you like this model also make sure to checkout the other models Specna Arms Offers over in our Replica Airguns Canada and US Online Stores.
Type: AEG Airsoft Rifles Manufacturer:Specna Arms. Model:Core SA-C07-PDW Materials: Fiberglass reenforced plastic and metal/aluminum. Weight: 5.27 pounds ( 2.39 kg). Total Length: 27.2 - 30.3 inches (690 - 770mm). Barrel: 10.63 inch (270) inner 6.03mm tight bore barrel non rifled. Propulsion: AEG. Action: Single action semi & full auto. Ammunition Type: .6mm plastic Airsoft BB’s. Ammunition Capacity: High cap 380 round magazines. FPS: 380 fps with installed spring, included M90 spring will be lower fps.
Trigger Pull: The trigger pull on the Specna Arms Core SA-C07-PDW AEG Airsoft Rifle is similar to a light single action trigger as they are essentially an electrical on off switch. There is a little bit of take up with virtually no extra friction to let you know when the release is going to be, with a bit of use you will figure out exactly when the trigger will release the action.
Accuracy: At this time I have not made my Field Test Shooting Video or even shot the Specna Arms Core SA-C07-PDW AEG Airsoft Rifle, but plan to very soon. You can checkout a previous video where I test out both Specna Arms RRA SA-C10 Core and E10 Edge which should perform similarly to the Specna Arms Core SA-C07-PDW AEG Airsoft Rifle
Build Quality: One thing I can say is no matter which version of the Specna Arms AEG Air Rifles you deicide to go with (either a Core or Edge Series), you are getting extremely good value for your money and neither one is going to have any low quality parts in it. Even the lower cost Core Series will have fiber glass reenforced plastic and metal parts along with a metal gearbox and virtually almost the same build as the more premium and slightly higher priced Edge Series. You will get upgrades in the Edge Series such as a an aluminum receiver and buffer tube, a GATE X-ASR Mosfet, the New Orion Gearbox, deep laser engraved licensing and an additional magazine. All of this for the little bit more you pay for an Edge series Specna Arms AEG Airsoft rifle.
Realism: The Specna Arms Core SA-C07-PDW AEG Airsoft Rifle is based on the AR15 or M16 platform of course in a very modern and PDW styled look. It looks and feels the part for sure with lots of working parts including the safety, selector switch, charging handle, dust cover, adjustable rear stock, pop-up front and rear sights as you would expect. Most of the hardware should be interchangeable with a real steel AR if you want to personalize the look of your Specna Arms Rifle.
Pros:
Super affordable yet very high quality product for what you pay.
Quality components throughout both the Core and Edge series.
Rock River Arms Licensed with hologram on receiver.
ESA™ quick spring change system makes spring changes quick and easy.
Comes with two springs for potential indoor and outdoor usage.
Plastic parts are fiberglass reenforced making them very durable.
Quick release fully adjustable pop-up sights.
No orange tips on our Canada Store versions.
Lots of rial mounting options even on such a short PDW styled AR.
Metal V2 Gearboxes with metal gears and mostly all metal parts inside.
Easy access to motor for any possible trouble shooting you any need to do
Cons:
Plastic receiver.
Need to hold back charging handle to access hop-up.
You will need a very compact battery setup with most Specna Arms models.
Comments:
Value for your money is what comes to mind when I think about the entire Specna Ams AEG Airsoft Riffle product line, especially with the Core series. The Specna Arms Core SA-C07-PDW AEG Airsoft Rifle is probably one of my more favorite versions as I really like PDW style compact AR’s in general. You will have to make sure you have on hand a very compact battery as space is extremely limited but other than that one main downside to this style of AEG everything else about it for the money is bang on and worth any slight compromises.
My Vimeo Table Top Review for the Specna Arms Core SA-C07-PDW AEG Airsoft Rifle:
I have another Huge Mystery Box to open and share with everyone, this one was even larger and heavier than the last one! You are going to have to watch the video to get all the details on what is actually inside but I can say there are 4 AEG Airsoft Rifles from a new to us company called Arcturus in both AR and AK versions and 2 CO2 Non Blowback Replica Pellet Pistols from KWC.
I do have a some more videos to make from the last Mystery Box Preview being a Specna Arms AEG PDW AR Airsoft Rifle and a Paintball Pump Shotgun that I still need to make both Table Top and Field Test Shooting Video for.
Starting with my velocity test, I shot 3 rounds through my Chronograph using .177 caliber 7 grain lead pellets achieving 482, 489 and 466 fps with an average of 479 for the three shots. Not bad for a fairly compact Break Barrel Airgun. This is perhaps fast enough for small game like mice and small rats but you would need to get proficient on your shot accuracy to make sure you got a good head or lung shot to make it a more humane pest control.
For the accuracy portion of this Field test Shooting Review I proceeded to fire 6 rounds into a paper target setup 30 feet away. I use a semi rested shooting position with the Umarex HK MP7 .177 Cal Break Barrel Pellet Gun resting on a sand bag up front and me sitting on a stool for stability. My 6 shot grouping was all within around 1.5 inches but I feel like this Pellet gun can do better with me getting a bit more use ot it, still not bad out of the box and with my first round shooting it.
I really like the Umarex HK MP7 .177 Cal Break Barrel Pellet Gun as not only a Replica but it also shoed itself ot be a decent target Airgun at the end of the day. I do have to say the trigger is a bit long but not heavy at all, it has a smooth pull with a soft release. Most pimple should be able towel with this just fine. SO if you are looking for a Replica but also want an Airgun that can shoot hard and with decent accuracy then look no further than the Umarex HK MP7 .177 Cal Break Barrel Pellet Gun.
In this Field Test Shooting Video Review I test out the brand new Crosman ST-1 CO2 Blowback Full Auto Steel BB Machine Gun in the Replica Airguns Indoor Airgun Range Sea Can to see what the actual velocity is along with accuracy. I first test fps using my Chronograph and I perform this test with and without the barrel extension to see how much the additional barrel length will increase velocity. I also shot the Crosman ST-1 CO2 Blowback Full Auto Steel BB Machine Gun in both semi auto shooting 10 rounds into my paper target setup 30 feet down range and then I perform a full auto 25 round magazine dump to see if the grouping expands or not.
Staring with the velocity test I did use brand new CO2 for this and the temperature was around 20 degrees Celsius or 68 Fahrenheit so not too cold or warm. With the Barrel extension installed I managed to average 418 fps shooting 4 rounds. With the barrel extension removed as expected the velocity did drop a bit down to 373 fps shooting 4 rounds and averaged out.
For my Accuracy Test I placed the Crosman ST-1 CO2 Blowback Full Auto Steel BB Machine Gun in semi auto for the first portion and fired 10 shots into the paper target setup 30 feet away, I was using a semi rested shooting position with a sand bag up front to rest the gun on and me sitting on a stool in the back. I did not sight the red dot in and found that out of the box the Crosman ST-1 CO2 Blowback Full Auto Steel BB Machine Gun shot down and too the right a fair amount but at least I was able to get most of the shots on the paper target and on camera. The grouping was around 2.5 to 3 inches so not super great but not bad either.
I then flicked the main selector to Full Auto since this is what most people want to see. I also reloaded the magazine with 25 rounds from the onboard hopper and unloaded the full magazine in a second or two. I did aim a bit higher and to the left this time to get the shots closer to the bullseye and I was able to do so with most of the 25 shots all within about 2.5 to 3 inches so not really any difference shooting in semi or full auto at least in terms of accuracy.
As I mention before in my Tabel Top Review for the Crosman ST-1 CO2 Blowback Full Auto Steel BB Machine Gun, it is a bit different looking and for me took a bit of getting use to but the good news is that it performs about the same as the other Crosman CO2 Full Auto Blowback BB Rifles in this similar lineup so if you like the look then don’t be afraid to pick one up over on our Canada or US replica Airgun Stores.
Type:Pellet Rifle. Manufacturer: Umarex Model:HK MP7 .177. Materials: Metal and Polymer. Weight: 4.4 pounds (2kg). Barrel: 11.7 inches (29.7cm). Total Length: 31 inches (78.7cm). Propulsion: Break Barrel Spring Piston. Action: Single Action Single Shot. Ammunition Type: .177 Caliber Pellets. Ammunition Capacity: 1. Max FPS: 490 Claimed.
Trigger Pull: The trigger on the Umarex HK MP7 .177 Cal Break Barrel Pellet Gun is single action only requiring you to break the barrel and compress the internal spring piston before you can shoot it. The actual trigger pull is pretty decent overall. There is very little take-up but the creep is on the longer side but fairly smooth requiring medium pressure. The release is a bit hard at first to predict but nothing some trigger time can’t get you use to.
Accuracy: I have not performed any shooting tests with the Umarex HK MP7 .177 Cal Break Barrel Pellet Gun so far. I hope to make that Video Review next week. I expect the Umarex HK MP7 .177 Cal Break Barrel Pellet Gun to perform well in the accuracy department especially with the included Red Dot Optical Scope installed. I hope the velocity rating from Umarex is based on lead pellets and not hyper velocity light weight pellets but we will find out the story when I perform my Field Test Shooting Video shortly!
Build Quality: The Umarex HK MP7 .177 Cal Break Barrel Pellet Gun is a China made Airgun but looks to be well made. It has lots of metal parts as you would expect from a Spring Piston Rifle which adds a nice weight and feel to it. I did however have an issue with the front plastic mock Suppressor/Compensator as it does not seem to be attached to the metal barrel very well other than being pressure fit which is not going to cut it with all the vibration a spring piston system makes. My first shot loosened the mock Suppressor/Compensator so I will either have to hold it when shooting or find another way to make sure it stays in place.
Realism: The Umarex HK MP7 .177 Cal Break Barrel Pellet Gun is kind of unique in this department as most break barrel rifles are not Replicas, especially the more compact sub machine gun styled ones. Umarex did good job making the Umarex HK MP7 .177 Cal Break Barrel Pellet Gun look like a real HK MP7 for the most part. Of course it is a Spring Piston Rifle at its core so exceptions had to be made to make this work including molded non working parts like the magazine release, sector switch and, bolt/ejection port. That said all in all it is a decent looking replica considering it is a Break Barrel Airgun under the skin.
Pros:
Not many Replica Pellet Rifles on the market, especially in a more compact gun.
Comes with Red Dot sight.
Lots of rails for adding accessories to it.
Full HK Licensed by Umarex.
Collapsible Wire Stock.
Nice high claimed 490 fps.
No need for CO2 so low cost to cooperate.
Not effected by temperature like a CO2 Airgun.
Should have better accuracy than most BB Replica Airguns.
Very solid feel to it, good overall weight and feel.
Cons:
Not going to be an action shooter, have to reload after each shot.
A good overall Replica but not as Realistic or full operation as a BB version would be.
Mock Suppressor/Compensator poorly attached to barrel.
Comments: The Umarex HK MP7 .177 Cal Break Barrel Pellet Gun is an interesting product, on one hadn't it is a Replica Airgun and most people expect a Replica Airgun to have all of the appropriate working parts similar to what would be found on the real steel version. But since this is a Break Barrel Airgun at the core the Umarex HK MP7 .177 Cal Break Barrel Pellet Gun will not function the same as the Real Steel version so as long as you don’t expect it to and appreciate the fact that it should be a nice accurate low cost to operate target rifle then I think you will understand this product and enjoy it for what it is… A Single Shot Pellet Rifle that looks a lot like a HK MP7.
Type: BB Rifle. Manufacturer: Crosman. Model: ST-1. Materials: Metal & plastic. Weight: 6.07 pounds (2.75 kilograms). Total Length: 17.75/33 inches (Pistol/Rifle). Barrel Length: 15.5 inches. Propulsion: 12 gram CO2 dual cartridges. Action: Blowback - single action only. Ammunition Type: 4.5mm steel BB's. Ammunition Capacity: 25 Round/Spring - 300 Round/Hopper. FPS: 480fps. Rate of Fire: 1400 rounds per minute in full auto
Trigger Pull: The trigger pull on the Crosman ST-1 CO2 Blowback Full Auto Steel BB Machine Gun is single action only since the right side charging handle must be cocked first before you can shoot it to engage the action. The trigger is short and fairly light but not overly light. The real fun happens with the Crosman ST-1 CO2 Blowback Full Auto Steel BB Machine Gun when you switch it over to full auto mode and with just one pull and hold of the trigger you empty the 25 round magazine in a mere matter of seconds at 1400 rounds per minute.
Accuracy: I have not actually shot this BB Rifle to date but expect it to get similar results to the other Crosman Full Auto BB Machine guns I have already reviewed. I am expecting a bit more velocity with the longer barrel extension installed and would be happy if I was able to get in the mid 400’s. Accuracy should also be about the same with 1 inch semi auto groups from 30 feet out expending a bit when in full auto.
Build Quality: The Crosman ST-1 CO2 Blowback Full Auto Steel BB Machine Gun is well made all around. Weighing in at 6.07 pounds without any add on accessories other than the included compact Red Dot sight. It feels solid and well built. There is a lot of metal going on inside and out of this rifle but keep in mind the top and bottom receiver are plastic with metal parts where they need to be like in the internals, pretty much all the working parts are metal, the magazine is full metal, the buffer tub is metal, charging handle, selector switch, magazine release, bolt release, trigger and of course the barrel is metal.
Realism: The Crosman ST-1 CO2 Blowback Full Auto Steel BB Machine Gun is not modeled after any real steel gun I know of. It resembles a futuristic weapon you would see in a SciFi Action Movie or Alien First Person Shooter. I was not a fan of it when it was first released by Crosman but after seeing and holding it in person it is growing on me quickly.
Pros:
Very unique, not like your regular Replica Rifles, very futuristic in design.
Drop out magazine doubles as the 300 round hopper and holds CO2 and BB’s.
Comes with Red Dot Sight and lots of rails for mounting what every you want on it.
Can be either a Pistol or Rifle or a PDW by adding or removing the Barrel Extension and Rear Stock.
Barrel Extension actual lengthens the barrel and should increase fps, not just for show!
Tactile comfortable rubber padding in multiple locations.
Semi auto and full Auto selectable.
Expected higher fps of up to 480.
Cons:
Some people may not like the look? Not like your normal modern rifle.
Front rubber grip comes off really easy at least on mine?
Will require barrel extension for full velocity.
Comments:
The Crosman ST-1 CO2 Blowback Full Auto Steel BB Machine Gun is a brave move by Crosman, I was not expecting something like this from them and when I originally saw it I was not sure if it was a good idea or not but again once seeing it in person and actually holing it I feel a lot better about it. It will for sure appeal to those looking for a futuristic Airgun or wanting something that looks like a gun from a video game or SciFi movie. I also like the versatility you have with the Crosman ST-1 CO2 Blowback Full Auto Steel BB Machine Gun being able to configure it how you like either as a Pistol, full on Rifle or PDW style shooter.
My Table Top Video of the Crosman ST-1 CO2 Blowback Full Auto Steel BB Machine Gun:
As the title suggest this a video about a Huge Mystery Box so I am not going to say what’s in it, I can say that their are 4 main products mostly rifles per-say. One is a Futuristic Full Auto BB Rifle, one is a Paintball Shotgun, One is an AEG Airsoft Rifle and one is a Replica Break Barrel Pellet Rifle.
So I have a lot of variety here to show everyone! I did absolutely zero research on any of the products I show in this video since like you I had no real idea what was inside other than how many and that most where rifle based.
Enjoy finding out what new products I will be reviewing over the next month with dedicated Table Top and Field Test Shooting videos.
Sights for guns in general are the same for Airguns as is with real steel guns for the most part and can be mixed and matched with a couple of exceptions. Spring piston rifles for instance are an exception because of the unique vibration the spring makes and how it can damage a standard optical sight, so in this case you’re best to use an optical sight designed for a spring piston Airgun. In most other cases sights can be used on all types of guns.
In this Airgun Sights video I will go over the various types of sights that either come as part of the gun design or can be added afterwards using a rail or mounting system.
Types of Airgun Sights most commonly used.
Iron Sight (Fixed or removable).
Iron Sight (Adjustable).
Iron Sight (White Dot, Fiber Optic).
Come in Post/Notch, Post/Aperture (Peep).
Common on Pistols and Rifles
Laser Sight:
Generally added to a rail or can sometime be integrated into the design of the gun.
Common on both Pistols and Rifles.
Red DotandHolographic:
Generally not magnified.
Most common on Rifles but can be used on Pistols.
Optical Magnified (Telescopic)
Come in a variety of magnifications for different shooting ranges.
Gun Safeties generally are going to be similar for all types of guns, so Safeties used with Airguns are often the same types as used with Real Steel Guns. Some guns will have no Safeties at all while other guns many have multiple Safeties on them. In this informative video I go over six of the more common types of Gun Safeties used in Real Steel Guns and Air Guns.
Here is a list of the more common types of gun Safeties.
There are many types of magazines used in Airguns and some of this is dependent on the ammunition used.
For instance a stacked type of magazine often used for Steel BB and Airsoft can not be used for Pellets as pellets tend to deform when stacked in such a way since there is no metal casting protecting them from mashing into each other.
So what type of magazines do we generally see in Airguns? The most common Airgun magazines are as follows:
Simple Stick Magazine
Mostly used with Steel BB but also found in some Airsoft Airguns.
Some Pellet Airguns use a type of stick magazine with a rotary magazine on each end.
Used in non-blowback and blowback Airguns.
Can be made from plastic or steel or a combination of both materials.
Full Size Drop Out Magazine
Used with Steel BB and Airsoft guns.
Generally you will find these types magazines hold both the BB’s and CO2.
Used in non-blowback and blowback Airguns.
Commonly used with Airsoft Rifles in mid to high capacity.
Can be made from plastic or steel or a combination of both materials.
Rotary magazine
Used with Steel BB, Airsoft and Pellet Airguns.
Used in non-blowback and blowback Airguns.
Can be made from plastic or steel.
Can often use mixed ammo types as in both 4.5mm Steel BB and .177 caliber pellet.
Belt Fed Magazine
Like rotary magazine belt fed magazine can accommodate Steel BB, Pellet and Airsoft but are most often used with Pellet Airguns.
Usually found in a full size magazine that also holds the CO2.
Used in non-blowback and blowback Airguns.
Can be made from plastic or steel or a combination of both materials.
Internal Magazine
Used with Steel BB, Airsoft.
Can have a hopper built in hat feeds a spring fed magazine.
Usually found in lesser expensive Airguns but not a rule.
In this Video I go through each type of Airgun Magazine and talk about their differences and uses.
