Type: AEG Airsoft Rifles Manufacturer:Specna Arms. Model: RRA SA-C10 / RRA SA-E10 Materials: Fiberglass reenforced plastic and metal/aluminum. Weight: C10 4.9 pounds ( 2.2 kg) - E10 5.1 pounds (2.3 kg). Total Length: 21.7 - 25.2 inches (550 - 640mm). Barrel: 6.7 inch (170mm) inner 6.03mm tight bore barrel non rifled. Propulsion: AEG. Action: Single action semi & full auto. Ammunition Type: .6mm plastic Airsoft BB’s. Ammunition Capacity: Mid cap 120 round magazines. FPS: 375 - 390 fps with installed spring, included M90 spring will be lower fps.
Trigger Pull: The trigger pull on both of the Specna Arms RRA SA-C10 Core and E10 Edge AEG Airsoft Rifles is similar to a light single action trigger as they are essentially an electrical on off switch. There is a little bit of take up with virtually no extra friction to let you know when the release is going to be, with a bit of use you will figure out exactly when the trigger will release the action.
Accuracy: At this time I have not made my Field Test Shooting Video or even shot the Specna Arms RRA SA-C10 Core and E10 Edge AEG Airsoft Rifles, but plan to very soon. They are next on my list for Filed Test Shooting Videos so stay posted for that video coming out soon. I do expect them to perform well and will be shooting both of these models side by side to see if there is any noticeable difference between the lower cost Core versus the slightly more premium Edge Specna Arms versions.
Build Quality: One thing I can say is no matter which version of the Specna Arms AEG Air Rifles you deicide to go with (either a Core or Edge Series), you are getting extremely good value for your money and neither one is going to have any low quality parts in it. Even the lower cost Core Series will have fiber glass reenforced plastic and metal parts along with a metal gearbox and virtually almost the same build as the more premium and slightly higher priced Edge Series. You will get upgrades in the Edge Series such as a an aluminum receiver and buffer tube, a GATE X-ASR Mosfet, the New Orion Gearbox, deep laser engraved licensing and an additional magazine. All of this for the little bit more you pay for an Edge series Specna Arms AEG Airsoft rifle.
Realism: The Specna Arms RRA SA-C10 Core and E10 Edge AEG Airsoft Rifles are based on the AR15 or M16 platform of course in a very modern and PDW styled look. They look and feel the part for sure with lots of working parts including the safety, selector switch, charging handle, dust cover, adjustable rear stock, pop-up front and rear sights as you would expect. Most of the hardware should be interchangeable with a real steel AR if you want to personalize the look of your Specna Arms Rifle.
Pros:
Super affordable yet very high quality product for what you pay.
Two options to consider, both with good price points and value.
Quality components throughout both the Core and Edge series.
Rock River Arms Licensed with hologram on receiver.
ESA™ quick spring change system makes spring changes quick and easy.
Comes with two springs for potential indoor and outdoor usage.
Plastic parts are fiberglass reenforced making them very durable.
Quick release fully adjustable pop-up sights.
No orange tips on our Canada Store versions.
Lots of rial mounting options even on such short PDW styled AR’s.
Metal gearboxes with metal gears and mostly all metal parts inside.
Easy access to motor for any possible trouble shooting you may need to do.
Cons:
Popup sights are mostly plastic..
Need to hold back charging handle to access the hop-up wheel.
Comments:
Value for your money is what comes to mind when I think about the entire Specna Ams AEG Airsoft Riffle product line. And this goes for not only the lower priced Core Series but also the premium Edge Series. Both version are built supper tuff with quality components throughout. You are just getting upgrades you are probably going to do at some point in time with the Edge Series and of course more metal components when you spend about $100 more for a similar Edge version. I figure if you can muster up the extra cash then go with an Edge Specna Arms AEG Airsoft Rifle, that said, any of the Core models will be money well spent.
Make sure not also watch my previous Specna Arms YouTube Video where I introduce the product line, show you around several models and talk about the key differences between the Core and Edge versions.
My Vimeo Table Top Review for the Specna Arms RRA C10 Core & E10 Edge Airsoft Rifles:
We have a new line of Airsoft rifles from Specna Arms I am super happy to be introducing to the Replica Airguns Airsoft Community.
Specna Arms AEG Airsoft Rifles are extremely cost effective and offer value for what you pay that is amazing. In this YouTube Introduction Video I go over the main differences between the Core Series (lower priced) versus the Edge Series (mid priced) so that you can understand what the extra cost will get you when buying a Spenca Arms Edge Series AEG Airsoft Rifle over a Specna Arm Core Series AEG Airsoft Rifle.
I also show 12 different versions from the Specna Arms Core and Edge Series some with Rock River Arms licensing and some without.
Specna Arms Core Series
Price: Mid $200’s (CAD)
Materials: Fiberglass Reenforced Plastic & Metal
Mosfet System: No
Gear Box: Ver 2 Metal Fully Upgradeable
Spring System: ESA Quick Change - 2 Springs (380-310 fps)
If you are interested more in the specifications and details fo reach of these Umarex Glock Licensed Air Pistols you can watch my Table Top Comparison Video where I go into the details and explain the differences of these Glock CO2 BB Pistols.
In Part 2 I test out how accurate each of these Umarex Glock Licensed Air Pistols is side by side to see if Non-blowback versus Partial-blowback versus Full-blowback makes much of a difference? The results may surprise you a little bit so make sure to watch the entire video to see how which Umarex Glock CO2 BB Pistol performs shooting at a paper target from 30 feet away using a rested and seated shooting position for best results.
Here again are the Umarex Glock Licensed CO2 BB Pistols I test out in this Review:
In this Vimeo Shootout Comparison Video I test head to head four Umarex CO2 BB GLock Air Pistols to see what the real world FPS is for each of them and I also give a little bit of my feedback on them at the end of the video. If you are wondering about their accuracy that will be covered in my next video coming out really soon…
And by the way I you want a little more info on these four Umarex Glock Air Pistols then Checkout my Table Top Comparison Video I made earlier for them.
Here are the Umarex Glock CO2 BB Pistols I test out in this Video Review:
I have review all three of these super fun Full Auto CO2 BB Rifles so make sure to watch those YouTube Field Test Video Shooting Reviews to see how they performed on their own in the Sea Can Indoor Airgun Shooting Range.
In this Field Test Shooting Video I have a little bit of fun to see which of the three Full Auto CO2 BB Rifles is the King in terms of FPS Velocity and all out full auto mag dump acuracy.
All there of these BB Rifles are awesome and I highly recommend picking one up or maybe even all of them! You can get them in our Canada and US Replica Airgun Stores…
Type: Pellet Pistol Manufacturer:Diana. Model:Bandit Materials: Wood and Metal, some plastic. Weight: 2.2 pounds (1000 grams). Total Length: 20.1 inches (51 cm) Barrel: 9.5 inches (24 cm), metal rifled. Propulsion: PCP. Action: Bolt. Ammunition Type: .177 & .22 Caliber pellets. Ammunition Capacity: Single shot to 9 & 7 round magazines.. FPS: 725 (.177) - 630 (.22). Need to test for Canada import version
Trigger Pull: The trigger pull on Diana Bandit PCP .177 Caliber Bolt Action Pellet Pistol is single action only meaning in order to cock the internal hammer/striker, you need to cycle the bolt back and forth allowing for a short and light trigger action. It does come with a rotary multi-round magazine that allows for the cycling of the bolt to automatically advance a pellet allowing for much quicker followup shots.
Accuracy: At this point I have not personally tested the Diana Bandit PCP .177 Caliber Bolt Action Pellet Pistol in terms of actual power and accuracy but I expect the Diana Bandit PCP .177 Caliber Bolt Action Pellet Pistol to perform well since in fact this is a target pistol with fairly high claimed fps. In the next few weeks I plan on making my Field Test Shooting Video so stay posted for the results from that video for confirmation of the performance.
Build Quality: The Diana Bandit PCP .177 Caliber Bolt Action Pellet Pistol is made in China which might make you wonder about the overall quality of this target pistol but after taking a good look around and working all the mechanical parts I ma very impressed with the overall quality and chosen material that went into the production of the Diana Bandit PCP .177 Caliber Bolt Action Pellet Pistol. You will finds metal where you need it as in the barrel, bolt and trigger. The pistol grip are made of wood but you will find some portions of the sights are plastic but it would have been nice if they where all metal.
Realism: Realism isn’t really a concern with the Diana Bandit PCP .177 Caliber Bolt Action Pellet Pistol since it is not a Replica Airguns but in terms of looking like a gun it serves that purpose, no mistaken that so no waving it around in public or things may not turn out so good for you…
Pros:
Inexpensive fairly high quality full featured target pistol for the price.
Expect good accuracy!
Metal construction where it needs to be (Bolt, barrel, trigger).
Rifled barrel.
Fully adjustable sights.
Adjustable and light single action trigger.
Dove tail on bolt for adding optical sight.
Nice wood pistol grip.
Good for small pest control because of fairly high fps and expected good accuracy for shot placement ability.
Overall the gun feels really high quality for the price.
Even comes with a nice soft shell case.
Available in both .22 and .177 caliber pellet versions.
Cons:
Grips may be a bit too wide for smaller handed shooters.
Allen key does not fight the trigger adjustment.
Made in China.
Will need a pump or way to pressurize.
Comments:
For the price I don’t think you will find anything out there in terms of a PCP target pellet pistols with as many features as the Diana Bandit PCP .177 Caliber Bolt Action Pellet Pistol. At least in the lower cost price point Diana is offering it at. For that reason it is not going to be the absolute best all around PCP pellet firing target pistol you can get but I am sure bang for your buck you will be happy with this one. Everything about the Diana Bandit PCP .177 Caliber Bolt Action Pellet Pistol feels good quality, I would expect to pay at least double the price for something similar for sure. I have a feeling keeping the Diana Bandit PCP .177 Caliber Bolt Action Pellet Pistol in stock is going to be a challenge for us so if you see it in stock don’t take too long making up your mind or you may be in for a bit of a wait.
My Vimeo Table Top Review for the Diana Bandit PCP .177 Caliber Bolt Action Pellet Pistol:
Trigger Pull: The trigger pull on Diana Chaser CO2 .177 Caliber Bolt Action Pellet Pistol is single action only meaning in order to cock the internal hammer/striker, you need to cycle the bolt back and forth allowing for a short and light trigger action. If you do purchase the rotary magazine the cycling of the bolt will automatically advance a pellet allowing for much quicker followup shots.
Accuracy: At this point I have not personally tested the Diana Chaser CO2 .177 Caliber Bolt Action Pellet Pistol in terms of actual power and accuracy but I expect the Diana Chaser CO2 .177 Caliber Bolt Action Pellet Pistol to perform well since in fact this is a target pistol with fairly high claimed fps. In the next few weeks I plan on making my Field Test Shooting Video so stay posted for the results from that video for confirmation of the performance.
Build Quality: The Diana Chaser CO2 .177 Caliber Bolt Action Pellet Pistol is made in China which might make you wonder about the overall quality of this target pistol but after taking a good look around and working all the mechanical parts I ma very impressed with the overall quality and chosen material that went into the production of the Diana Chaser CO2 .177 Caliber Bolt Action Pellet Pistol. You will finds metal where you need it as in the barrel, bolt and trigger. The pistol grip is plastic and so are portions of the sights which would have been nice if they where all metal.
Realism: Realism isn’t really a concern with the Diana Chaser CO2 .177 Caliber Bolt Action Pellet Pistol since it is not a Replica Airguns but in terms of looking like a gun it serves that purpose, no mistaken that so no waving it around in public or things may not turn out so good for you…
Pros:
Very inexpensive fairly high quality full featured target pistol.
Expect to have good accuracy and power!
Metal construction where it needs to be (Bolt, barrel, trigger).
Rifled 8.3 inch barrel.
Fully adjustable sights.
Adjustable and light single action trigger.
Dove tail on bolt for adding optical sight if you want to.
Extra storage for a backup CO2 in the pistol grip.
Good for small pest control because of fairly high fps and expected good accuracy for shot placement ability.
Can be modified/upgraded with a magazine, longer barrel and rifle stock fairly easily.
Overall the Airgun feels really high quality for the price.
Even comes with a nice soft shell case.
Available in both .22 and .177 caliber pellet versions.
Cons:
Does not come with magazine, single shot only out of the box.
Allen key does not fit the trigger adjustment screw.
Made in China.
Comments:
For the price I don’t think you will find anything out there in terms of target pellet pistols with as many features as the Diana Chaser CO2 .177 Caliber Bolt Action Pellet Pistol. At least in the rather low cost price point Diana is offering it at. For that reason it is not going to be the absolute best all around CO2 pellet firing target pistol you can get but I am sure bang for your buck you will be happy with this one. Everything about the Diana Chaser CO2 .177 Caliber Bolt Action Pellet Pistol feels decent quality, I would expect to pay at least double the price for something similar for sure. I have a feeling keeping the Diana Chaser CO2 .177 Caliber Bolt Action Pellet Pistol in stock is going to be a challenge for us so if you see it in stock don’t take too long making up your mind or you may be in for a bit of a wait.
My Vimeo Table Top Review for the Diana Chaser CO2 .177 Caliber Bolt Action Pellet Pistol:
Type: Airsoft Pistol. Manufacturer:KWC. Model: PT92 Materials: Almost entirely all Metal. Weight: 2.4 pounds (1089 grams). Barrel: 4.5 inches, metal non-rifled. Propulsion: 12 gram CO2. Action: Semi and full auto, single and double action with full blowback. Ammunition Type: 6mm Plastic Airsoft BB's. Ammunition Capacity: 27 rounds full size drop out metal magazine. FPS: 388 using .25 gram Airsoft BB’s.
Trigger Pull: The trigger pull on the KWC PT92 CO2 Blowback Airsoft Pistol is good in both single and double action. Of course in single action the trigger is much shorter and lighter but that said double action is still very usable. Once you fire a round in either double or single action the blowback action will continue to cock the hammer back allowing for single action followup shots.
Accuracy: The KWC PT92 CO2 Blowback Airsoft Pistol performed OK during my Field Test Shooting review in terms of accuracy. I shot it first in semi auto to get a sense of the overall accuracy and in terms of elevation it was right in the middle of the target. I did find the shots spread out a bit side to side perhaps as much as 4-5 inches during my test grouping. As expected when I flipped the happy switch to full auto the KWC PT92 CO2 Blowback Airsoft Pistol pretty much sprayed the target working its way up as the recoil from the full auto blowback action lifted the barrel. In terms of power the KWC PT92 CO2 Blowback Airsoft Pistol shot pretty hot, I was using .25 gram Airsoft BB’s and was still able to achieve close to 400 fps.
Build Quality: The KWC PT92 CO2 Blowback Airsoft Pistol like the other all metal KWC made Beretta 92 or Taurus PT92 copies out there being sold under different company names, is a good value blowback Beretta Taurus Airgun no matter which version you get. It’s not the best or worst, right about in the middle but most of the bugs have been worked out since it came out just after the KWC 1911 line and that’s been out for some time now. I find the finish does come off a bit easy but when this happens it kind of gives the Airgun a more realistic and slightly worn in look to it.
Realism: The KWC PT92 CO2 Blowback Airsoft Pistol is a One to One replica of the real steel Taurus PT92 and does a great job at replicating it. You would be hard pressed to see any differences in the Airgun version versus the 9mm caliber firing version until you pick one up and work the parts a bit. Even so pretty much all the mechanical parts work the same as a real steel Taurus PT92 including the ability to filed strip the Airgun version and gain access to the hop-up and other internal parts.
Pros:
All metal construction.
Full length blowback action with nice heavy recoil.
Accurate Taurus PT92 replica.
Single and double action triggers both feel good.
Double stack style metal magazine holds the CO2 and Airsoft BB’s.
No ugly white writing ( warning instructions) on the gun.
Fully filed strippable.
Adjustable Hop-up.
Recessed barrel for added realism.
FPS is fairly high for a full blowback gun.
Cons:
Finish on KWC guns can wear off quickly in the high spots but has gotten better over the years.
Full blowback action especially when in full auto mode will eat up a lot of CO2.
Comments: If you are a Beretta 92 or Taurus PT92 fan than I am sure you have already taken a look at the KWC line of Beretta 92 and Taurus PT92 Airguns, maybe in a steel BB version or Airsoft version? KWC first offered it in this PT92 style and then later brought out a more true to form Beretta 92 version. Depending on where you live and which model you buy you may or may not have the full auto feature but to be honest full auto is fun at first but then you realize you don’t really hit much with it and just end up wasting a lot fo CO2 and BB’s. Checkout our Replica Airguns Canada and US Stores for all the different versions and models of this KWC Beretta and Taurus style Airgun.
My Vimeo Video Review for the KWC PT92 CO2 Blowback Airsoft Pistol:
Type: Airsoft Pistol. Manufacturer:KWC. Model: M1911 Materials: Almost entirely all Metal. Weight: 1.97 pounds (894 grams). Barrel: 4.5 inches, metal non-rifled. Propulsion: 12 gram CO2. Action: Semi auto, single action only with full blowback. Ammunition Type: 6mm Plastic Airsoft BB's. Ammunition Capacity: 14-15 rounds full size drop out metal magazine. FPS: 360+.
Trigger Pull: The Single Action Only trigger pull on the KWC M1911 CO2 Blowback Airsoft Pistol is exactly as it should be and just like what you would find on a real steel Colt 1911 pistol. That would be short, light and crisp. As there is no double action mode, you are required to rack the slide back to chamber a rounds and cock the hammer for the first shot, afterwards the blowback action will do this for you.
Accuracy: I wasn’t overly impressed with the accuracy of the KWC M1911 CO2 Blowback Airsoft Pistol when I tested it out in the Replica Airguns Indoor Sea Can Airgun Range but it is what it is. The M1911 shot really high and a bit loose getting about a 5 inch 10 shot grouping, perhaps a hop-up adjustment was in order but this is how it shot right out of the box which is how I test all my Airguns. In terms of power the KWC M1911 CO2 Blowback Airsoft Pistol was bang on shooting .25 gram Airsoft BB’s at right around 350 fps.
Build Quality: The KWC M1911 CO2 Blowback Airsoft Pistol like the other all metal KWC made 1911’s out there being sold under different company names, is a good value Blowback 1911 Airgun no matter which version you get. It’s not the best or worst, right about in the middle but most of the bugs have been worked out since this is one of the longes CO2 1911’s out there and for the most part has stayed about the same. I find the finish does come off a bit easy but when this happens it kind of gives the 1911 Airgun a more realistic and slightly worn in look to it.
Realism: The KWC M1911 CO2 Blowback Airsoft Pistol is a One to One replica of the real steel M1911 A1 and does a great job at replicating it. You would be hard pressed to see any differences in the Airgun version and the .45 caliber firing version until you pick one up and work the parts a bit, even so pretty much all the mechanical parts work the same as a real steel M1911 A1 including the ability to filed strip the Airgun version and gain access to the hop-up and other internal parts.
Pros:
All metal construction.
Full length blowback action with nice heavy recoil.
Accurate Colt M1911 A1 replica.
Single action only trigger feels good, short light and crips.
Accurate trigger design and working grip safety.
Metal magazine holds the CO2 and 14-15 Airsoft BB’s.
No ugly white writing (warning instructions) on the slide of the gun.
Fully filed strippable.
Adjustable Hop-up.
Recessed barrel for added realism.
FPS is just about perfect, just over 360 fps using .20 gram BB’s, not too powerful but Canada import friendly.
Cons:
Finish on KWC guns can wear off quickly in the high spots but has gotten better over the years.
Full blowback action will eat up a lot of CO2.
Comments: I have always been a fan of the 1911 pistol and the KWC M1911 CO2 Blowback Airsoft Pistol is no exception to this. Like all of the KWC 1911’s out there being redistributed by the big airgun companies the KWC version is really no different other than more simple KWC branding and with no licensing on the Airgun to speak of. Some people prefer the cleaner look to it and some will like to have licensed versions, to each their own. Do some looking around on our website and find a KWC made 1911 you like best, perhaps a simple KWC M1911 A1 like the one reviewed here or maybe a more tactical version with all the more modern updates to it like a rail, ambidextrous controls and tactical triggers and hammers.
My Vimeo Video Review for the KWC M1911 CO2 Blowback Airsoft Pistol:
If you have not already watched my Preview video for both of these Airsoft pistols then make sure to watch that video for details and specifications along with some nice tight shots of each Airsoft gun.
Another multi gun Field Test Shooting Review, in this Indoor Sea Can Field Test Shooting Video I test out the KWC M1911 and PT92 Full Blowback CO2 Airsoft Pistols. I first place 5 6mm .25 gram plastic Airsoft BB’s through my Chronograph to find out what the real world velocity is for each Airsoft Pistol and then I perform my accuracy test where I shoot multiple rounds into a paper target 30 feet down range to see how close of a grouping I can get with each Airgun. I use a seated and rested shooting position to eliminate as much human factor as possible. By the way is used a brand new 12 gram CO2 and the temperature was 25 degrees Celsius (77 degree Fahrenheit) inside the Airgun Sea Can Shooting Range.
Starting with the KWC M1911 CO2 Blowback Airsoft Pistol I averaged 351 fps with the fastest shot being 353 and the slowest shot 345, so very consistent for sure! Accuracy for the KWC M1911 CO2 Blowback Airsoft Pistol could have been a bit better, I had to adjust my aim point to just under the bottom rings and even so the KWC M1911 wanted to shoot high, I was able to get around a 5 inch 10 shot grouping but was hoping for a bit better.
Next I tested out the KWC PT92 CO2 Blowback Airsoft Pistol which does have a full auto option. For the velocity portion of my Field Test the KWC PT92 did shoot a bit after than the MWC M1911 getting an average fps of 388 with the fastest shot hitting 396 and the slowest shot at 383 so again very consistent performance. Since the KWC PT92 CO2 Blowback Airsoft Pistol is capable of full auto shooting I decided to shoot 5 rods on my paper target to get a base accuracy and this resulted in a bit of a lateral spread fairly close to the bullseye about 4-5 inches apart. I then did a mag dump and as expected pretty much sprayed 6mm Airsoft BB’s all over the place but most shot a bit high and to the left probably because of the blowback recoil action.
The KWC M1911 and PT92 CO2 Blowback Airsoft Pistols are both classic Airguns and great options if your looking for a 1911 or Beretta styled Airgun to add to your collection without all the markings and white writing on them.
This is a combined Filed Test Shooting Video for the KWC 2022 NBB - 24/7 NBB - 24/7 Blowback CO2 BB Pistols. I already made an update video for these KWC Steel BB Pistols since they are slightly different version I have not covered in any video beforehand.
As per my typical Field Test Shooting Videos I first place 5 shots through my Chronograph to test out the real world fps of each gun. I then shoot 10 rounds on a paper target setup 30 feet away using a seated and rested shooting position. My ammo for this test was 5.1 grain zinc coated 4.5mm Steel BB’s for all airguns along within a brand new 12 gram CO2. The temperature in my indoor Sea Can Airgun Shooting Range was around 25 degrees Celsius (77 degrees Fahrenheit) for this test.
First up was the KWC 2022 NBB 4.5mm CO2 Steel BB Pistol with an average five shot fps of 347. The KWC 2022 NBB 4.5mm CO2 Steel BB Pistol was the least accurate of the three Airguns tested on this day getting about a 5-6 inch 10 shot grouping. I did notice when I went to edit the video that it did shoot a double shot on the first shot which lowered that first shot making the group a bit larger. This may have been as a result of pulling the trigger with the safety on right before which probably loaded a round into the barrel followed by the second pull loading a second BB into the barrel.
I then tested out the KWC 24/7 NBB 4.5mm CO2 Steel BB Pistol which was by far the most powerful Airgun tested out of the three hitting a top fps of 452 with a five shot average of 420 fps! The KWC 24/7 NBB 4.5mm CO2 Steel BB Pistol was also fairly accurate getting a nice 2 inch 10 shot grouping, slightly to the left and just under the bullseye. Nothing wrong with that!
The last KWC 4.5mm Steel BB pistol for the day was my KWC 24/7 Blowback CO2 4.5mm Steel BB Pistol. The only only blowback single action shooter out of the bunch. As expected from a blowback CO2 Airgun the fps was lower averaging just under 300 fps (298 to be precise). The surprise of the day was the accuracy from the KWC 24/7 Blowback CO2 4.5mm Steel BB Pistol was the best out of this test group getting really close to a 1 inch grouping very well centered just a tad to the right but with near perfect elevation.
Depending on what you are going for, all of these Airguns are great choices. If you want ultimate power perhaps go for the KWC 24/7 NBB 4.5mm CO2 Steel BB Pistol with its 450+ fps, if you want accuracy and realism then I would suggest the KWC 24/7 Blowback CO2 4.5mm Steel BB Pistol with its full blowback action and excellent accuracy.
This Field Test Shooting Review for the Daisy Powerline 340 Spring BB Pistol is a lot different from most of my other shooting video reviews mainly because the Daisy Powerline 340 Spring BB Pistol is not a CO2 powered BB Pistol like pretty much every other 4.5mm Steel BB pistol I have ever tested. There are way more 6mm Airsoft spring pistols but when it comes to actual 4.5mm BB Pistols they are not very common. The Daisy Powerline 340 Spring BB Pistol is Kind of like the pistol version of the Daisy Red Ryder BB Rifle…
So let’s get right into the nitty gritty on how the Daisy Powerline 340 Spring BB Pistol performed in the Replica Airguns Indoor Sea Can Airgun Shooting Range. Starting off with the feet per second velocity for the Daisy Powerline 340 Spring BB Pistol Daisy claims around 240 fps. shooting about 8 shots through my chronographs with standard 5.1 grain 4.5,, steel BB’s I was able to get an average of just over 180 fps, the Daisy Powerline 340 Spring BB Pistol was super consistent shooting all shots between 181 and 189 fps.
I then proceeded to place 10 shots on my paper target setup 30 feet down range shooting from a rested portion with a sand bag up front supporting my hadbn’s and a stool to sit on in the back. The Daisy Powerline 340 Spring BB Pistol did shoot a bit low and to the left but all 10 shots grouped within 3 inches of each other, actually a bit better than I was expecting from a low cost BB Pistol like this. If I was shooting at a pop can and adjusted my aim point a bit I would have hit the can 10 out of 10 times which is about as good as you can ask for a plinker like this.
The best way I can describe the Daisy Powerline 340 Spring BB Pistol is the pistol equivalent of the Daisy Re Ryder in that it shoots 4.5mm Steel BB’s has a high capacity BB reservoir that holds lots of BB’s and you are required to cock the spring for each shot rather than use CO2 for power. This makes for an over low cost Airgun but like the Daisy Red Ryder it is a lot fo fun to shoot at the end of the day. The Daisy Powerline 340 Spring BB Pistol has a surprisingly good trigger and at the end of the day shot really consistently for me.
Type: BB Pistol. Manufacturer: Daisy Model:Powerline 340. Materials: Mostly metal construction. Weight: 1 Pound (454 grams). Barrel Length: 4-5 inches Total Length: 8.5 inches. Propulsion: Spring Action: Single action only. Ammunition Type: 4.5mm steel BB’s. Ammunition Capacity: 13/200 round magazine. Max FPS: 240 fps.
Trigger Pull: The Daisy Powerline 340 Spring BB Pistol has a single action only trigger. You will have to pull the slide back for each shot as this motion draws the spring back and also cocks the hammer. The trigger pull is fairly decent with about a quarter inch of take-up followed by a light predictable release. There will not be any action shooting since the trigger is not double action and the fact that the slide must be pulled back for each shot.
Accuracy: So far I have not made my Field Test Shooting Video for the Daisy Powerline 340 Spring BB Pistol but I did take it outside for some good old plinking to see how it would perform causally shooting in the yard. The Daisy Powerline 340 Spring BB Pistol shot a bit harder than I was expecting it to and I was even able to hit targets a good 50 or so feet away but did have to account for some trajectory arch. Accuracy seemed good in general without a lot of need to adjust my aim point as the sights seemed well centered out of the box which is good since they are not adjustable.
Build Quality: The build quality of the Daisy Powerline 340 Spring BB Pistol is nothing exciting as it is mostly plastic with a metal barrel and perhaps a few other internal metal parts. Being that the Daisy Powerline 340 Spring BB Pistol is mostly plastic it only weighs in at about a pound but feels good in the hand. Everything feels pretty solid on the airgun with good overall fit and finish.
Realism: In terms of realism the Daisy Powerline 340 Spring BB Pistol is a good replica of a Beretta 92 in terms of looks and size comparison. Other than the open slide area that exposes the inner barrel being shorter than a real steel Beretta (probably to accommodate the internal spring) the Daisy Powerline 340 Spring BB Pistol looks very close to a Beretta 92. Moving parts include the slide, hammer, magazine release and slide catch release which is actually the safety. Even the magazine is drop out and near full size. I also like that there are no perceivable screw holes which is usually the case with these types of low cost all plastic Airguns when they are basically two halves slapped and screwed together.
Pros:
Pretty decent replica of a Beretta 92 in general.
For an inexpensive Airgun it has a lot of working parts that make it more realistic.
Very low cost to buy and operate, no CO2 required (Under $40 in Canada Store right now).
Has a recessed barrel for added realism.
Single action only trigger is not overly long or heavy.
Lots of ammo stored in the internal hopper so no need for a lot reloading.
Safety actually looks like part of the gun built into the slide catch release.
Full size dropout magazine.
Weight and feel of gun are pretty good considering so much plastic.
Cons:
Not super high in the fps department.
Need to cock the slide for every shot so not going to be an action shooter.
Made in China.
Comments: The Daisy Powerline 340 Spring BB Pistol is one of those low cost yet kind of fun BB guns that as long as you don’t have super high expectations you will get a ton of fun out of for very little cost. At about $40 Canadian with a bit more for some 4.5mm steel BB’s you are ready to shoot all day long. I was a bit surprised at how decent of a little BB gun the Daisy Powerline 340 Spring BB Pistol is. It looks real enough, has a decent build quality to it, actually shoots pretty good with a nice trigger and for such a low cost airgun it has a lot going for it like lots of working parts and even a removable full size magazine that doubles as a 200 round hopper with 13 round internal magazine. I don’t think anyone will be disappointed buying the Daisy Powerline 340 Spring BB Pistol and it would make a perfect first BB gun for a younger person looking to get started out in the sport.
My Vimeo Table Top Review for the Daisy Powerline 340 Spring BB Pistol:
Type: Pellet Revolver. Manufacturer: Gamo Model:PR-776. Materials: Mostly metal construction. Weight: 2.2 Pounds (1 kg). Barrel Length: 6 inches Total Length: 11.5 inches. Propulsion: CO2 x1 Action: Revolver single and double action. Ammunition Type: .177 caliber pellets. Ammunition Capacity: 8 rounds per magazine. Max FPS: 400+ fps.
Trigger Pull: The Gamo PR-776 CO2 .177 Caliber Pellet Revolver has your traditional revolver single and double action trigger setup. In double action, the trigger is going to be a bit longer and heavier but it feel fairly smooth with no real friction points and I would consider it to have a medium trigger pull. When you cock the hammer back placing the Gamo PR-776 CO2 .177 Caliber Pellet Revolver in single action, the trigger pull becomes very short with virtually no take-up at all and the weight of the trigger is very light allowing for more accurate shots.
Accuracy: Make sure to watch my Field Test Shooting video for the Gamo PR-776 CO2 .177 Caliber Pellet Revolver where I test out the velocity and accuracy in the Replica Airguns Indoor Airgun Shooting Range. In summary the Gamo PR-776 CO2 .177 Caliber Pellet Revolver shot a little bit hotter than claimed at just over 400 fps using around 7 grain lead pellets. In terms of accuracy with a total of 16 shots the grouping spread out to around 4 inches but I am pretty sure a different pellet choice may have made a difference.
Build Quality: The build quality of the Gamo PR-776 CO2 .177 Caliber Pellet Revolver is pretty good overall. It is mostly all metal with the exception of the grips of course, Fit and finishes looks good, everything feel snug adn tight with the exception of the pistol grips. I feel like the grips could easily move out of place and get caught on something. This is not a problem when shooting, more so when in a holster. The Gamo PR-776 CO2 .177 Caliber Pellet Revolver feels good in the hadn't, nice and solid and with a good weight to it.
Realism: The Gamo PR-776 CO2 .177 Caliber Pellet Revolver is a decent looking Airgun in the style of a traditional revolver, I wouldn’t say it’s an exact replica of any specific revolver in production but it does tick off all the boxes in terms of looking realistic. The weight and feel for now and the Gamo PR-776 CO2 .177 Caliber Pellet Revolver also has a recessed barrel and hidden CO2 crew. The only real giveaway would be the cylinder size as it is a bit smaller than expected and of course is chambered for .177 caliber pellets.
Pros:
Good power over 400 fps using actual lead pellets.
Quicker reloading over shell loading revolvers
More shots per magazine reload, 8 versus 6.
Comes with two metal 8 round magazines.
Traditional single and double action trigger.
White dot front sight with fully adjustable rear sight.
Good weight and feel to it.
Fit and finish look good.
Recessed barrel for realistic looking barrel opening.
Should be able to use a dovetail type scope mount for adding on a red dot or magnified scope.
Cons:
Not a fan of the loose pistol grip setup to access the CO2.
Was hoping to get a bit tighter grouping but may have been a pellet choice issue.
Comments: It was nice reviewing the Gamo PR-776 CO2 .177 Caliber Pellet Revolver as it was a bit different then most of today shell loading revolvers. I like that the Gamo PR-776 CO2 .177 Caliber Pellet Revolver still offered a realistic looking cylinder that the shell loading revolvers have but with the moon clip style magazines that allow for quick adn easy reloading of 8 rounds at a time. The velocity or power of the Gamo PR-776 CO2 .177 Caliber Pellet Revolver was even a bit high than Gamo claims using PBA Platinum pellets since Gamo claims 400 fps using these 5.1 grain lead pellets. My testing with closer to 7 grain pellets yielded fps up and over 400 fps. All the Gamo PR-776 CO2 .177 Caliber Pellet Revolver needs is to be just a little bit more accurate but I feel this may simply be more of a pallet choice, once you find a pellet the Gamo PR-776 CO2 .177 Caliber Pellet Revolver likes I am pretty sure it will deliver accurate shots.
My Table Top Review for the Gamo PR-776 CO2 .177 Caliber Pellet Revolver:
Type: Break Barrel Pellet Pistol. Manufacturer: Gamo Model:P900 IGT. Materials: Mostly plastic build with some internal metal parts. Weight: 1.28 Pounds (580 grams). Barrel Length: 6.25 inches Total Length: 12.52 inches. Propulsion: Gas Piston (IGT) Action: Break barrel single action trigger. Ammunition Type: .177 caliber pellets.. Ammunition Capacity: 1 round. Max FPS: 400 fps using PBA Platinum pellets (about 5 grain).
Trigger Pull: The trigger on the Gamo P900 IGT .177 Caliber Pellet Pistol uses what Gamo calls their SAT or Smooth Action Trigger system. Overall the single action only trigger feels pretty good, not super light but also not overly heavy. The Gamo P900 IGT .177 Caliber Pellet Pistol has a short take up with a very predictable release point. I found it fairly easy to use and shoot with precision.
Build Quality: The Gamo P900 IGT .177 Caliber Pellet Pistol is mainly made out of plastic, pretty much everything is plastic including the trigger but there will be internal metal parts where they are required. That said the Gamo P900 IGT .177 Caliber Pellet Pistol feels well made with fairly heavy plastic throughout. The Gamo P900 IGT .177 Caliber Pellet Pistol is not super heavy but feels hefty enough in the hand.
Realism: The Gamo P900 IGT .177 Caliber Pellet Pistol is not a replica of any specific pistol in production and has a very modern look to it. I would say it looks more like an airgun than a real gun and that’s exactly what is’t supposed to be so this is not a negative in this case.
Pros:
Reasonable price for a target pistol.
Performed well, can easily get .5 inch groupings from 30 feet away.
No need for CO2.
Inert Gas Technology (IGT) has less vibration and no reduction to power over time.
Fiber optic front sight.
Adjustable rear sight for windage.
Inexpensive to shoot.
Made in Spain.
Ambidextrous design.
Reasonable trigger pull.
Cons:
Not supper powerful. Shot around 300 fps with standard lead pellets.
A bit hard to cock because of such a short barrel.
Rear sight is only adjustable for windage and not elevation.
Comments: The Gamo P900 IGT .177 Caliber Pellet Pistol is a nice overall low cost target pistol with a very modern look and Gas Piston technology. In terms of performance the Gamo P900 IGT .177 Caliber Pellet Pistol tested well for me shooting accurately with a consistent 300 fps velocity which is what you want in a target pistol, consistency over raw power. I like the overall design and look, the Gamo P900 IGT .177 Caliber Pellet Pistol feels good in the hand and easy to shoot, the trigger is not overly light but is also not too heavy by any means. My only complaint is the cocking effort involved because of such a short barrel and I also noticed a bit of a stickiness with the cocking effort but I have a feeling this may break in over time or perhaps a drop of oil in the hinge area may do the trick. If you want a modern looking target pellet pistol with good performance than the Gamo P900 IGT .177 Caliber Pellet Pistol will for sure fit the bill!
My Table Top Review for the Gamo P900 IGT .177 Caliber Pellet Pistol:
For this Field Test Shooting Video Review of the Gamo P900 IGT .177 Caliber Pellet Pistol I test the power and accuracy to determine what the real world (fps) Feet Per Second velocity and how tight of a grouping I can get for 30 feet down range.
For the power portion of my Indoor Filed Test I shot five RWS 6.9 grain lead pellets through my Chronograph with an average velocity of 305 fps. This resulted in a 1.43 foot pound energy rating. My slowest shot out of the Gamo P900 IGT .177 Caliber Pellet Pistol was 289 fps and the fastest shot was 311 fps. Gamo claims the Gamo P900 IGT .177 Caliber Pellet Pistol can achieve 400 fps but this would be using lighter alloy pellets like PBA Platinum pellets.
Next I setup at a fresh paper target 30 feet down range and proceeded to place 8 shots into the target using a seated and rested shooting position. My first shot was a bit high as I was getting use to the trigger but the following 7 shots all grouped within about 3/4 of an inch, 6 of them all within a half inch of each other so the Gamo P900 IGT .177 Caliber Pellet Pistol is for sure capable of 1/5 inch groupings from a 30 foot distance. The placement of the shots grouping was a little bit high and to the left. since the Gamo P900 IGT .177 Caliber Pellet Pistol has an adjustable trigger for windage I could easily center the grouping right in the middle. In terms of elevation there is no adjustment so I would need to manually adjust this on the fly depending on the distance I was shooting at.
The Gamo P900 IGT .177 Caliber Pellet Pistol performed very well for me, the power is what you would expect for a target pistol, I would not recommend the Gamo P900 IGT .177 Caliber Pellet Pistol for any pest control. Accuracy was very good and I feel once getting use to the trigger you shoudl be able to get shots all within a 1/2 inch at 30 feet. The trigger is not super light but by no means is it heavy, the take-up is short with a predictable release, I found the trigger to work well overall. My only complaint is cocking the Gas Spring as the barrel is short and it does take some effort to do this, especially getting it started off, once you get past the first little bit it does get easier to cock. If you’re looking for a nice accurate target pellet pistol at a relatively inexpensive price point then for sure consider the Gamo P900 IGT .177 Caliber Pellet Pistol.
Type: BB Rifle. Manufacturer: Crosman. Model: R1 AR. Materials: Metal & plastic. Weight: 6 pounds (2.7 kilograms). Length: 26.25 / 29.25 inches (Stock closed / extended). Propulsion: 12 gram CO2 dual cartridges. Action: Blowback - single action only. Ammunition Type: 4.5mm steel BB's. Ammunition Capacity: 25 rounds. FPS: 430fps. Rate of Fire: 1400 rounds per minute in full auto
Trigger Pull: The trigger pull on the Crosman R1 CO2 Blowback BB Machine Gun is single action only since the charging handle must be cocked first before you can shoot it. The trigger is short and fairly light as you would expect from an AR type trigger action. The real fun happens with the Crosman R1 CO2 Blowback BB Machine Gun when you switch it over to full auto mode and with just one pull and hold of the trigger you empty the 25 round magazine in mere seconds.
Build Quality: The Crosman R1 CO2 Blowback BB Machine Gun is well made all around. Weighing in at 6 pounds without any add on accessories it feel solid and well built. There is a lot of metal going on inside and out of this rifle but keep in mind the top and bottom receiver are plastic with metal parts where they need to be like in the internals, pretty much all the working parts are metal, the magazine is full metal, the buffer tub is metal, charging handle, selector switch, magazine release, bolt release, trigger and of course the barrel is metal.
Realism: The Crosman R1 CO2 Blowback BB Machine Gun is about as real as you are going to get in a CO2 Blowback AR/M4 styled Airgun. You can even take it apart and split the top and bottom receivers like the real steal version. The blowback action gives you some recoil but more importantly offers a true single action trigger and of course the full auto ability we all love. Almost all the working parts work like they would on a real AR / M4 other than the forward assist which is moulded into the receiver.
Pros:
Super realistic working M4/AR 4.5mm BB Rifle just like the otters Crosman Rifles in this lineup.
Full blowback operation with both semi and full auto shooting, can feel the blowback operation rocking the gun.
Great weight and feel to it.
Almost everything works exactly like the real steel version. (Charging handle, dust cover, bolt release, magazine release, selector switch…)
Duel CO2 full metal drop out magazine that holds the 25 4.5mm steel BB’s as well.
Adjustable and customizable AR butt stock.
Included red dot sight and ability to add pop-up iron sights.
Lots of rails of mounting additional cool hardware.
Removable flash hider that uses standard threading.
Cons:
Receiver is plastic but well made and does not compromise feel or weight since there is lots of metal throughout this gun.
No iron sights included.
Comments:
The Crosman R1 CO2 Blowback BB Machine Gun is really pretty much the same as the Crosman DPMS SBR and Crosman MPW with more or less Cosmetic changes. Like the Crosman MPW the Crosman R1 has an AR compatible Rear stock and pistol grip, the Crosman R1 CO2 Blowback BB Machine Gun is the only Crosman AR Full Auto CO2 BB Rifle that has the ability to change out the flash hider, you can even put a mock suppression or in it if you choose to. No matter which of the Crosman AR Full Auto CO2 BB Rifles you chooses to get they are mechanically every similar and share most of the same parts. I would say the Crosman R1 CO2 Blowback BB Machine Gun is the most customizable to date but they are all fantastic Air Rifles!
My Table Top Video of the Crosman R1 CO2 Blowback BB Machine Gun:
My systems setup for a more powerful airgun as I was shooting .22 caliber lead pellets with about 11-12 foot pounds of energy. Direct hits passing through the 3/4 inch cut outs had no problem laying down the metal paddles and resetting the paddles was a lot easier than I though it would be even way back 50 feet.
I did not have my Sig Sauer Virtus PCP .22 Caliber Air Rifle perfectly sighted in so I did have to aim low and to the left which made it a bit harder dropping the plates but I did manage to get the job done at least for providing a decent test video fo the Rx Target Systems for the purposes of this video.
Make sure to not only watch my Field Test Shooting video included in this post but also checkout my Rx Target Systems Preview Video where I show it up and close and also go into more details on the Rx Target Systems and how modular and versatile it really is.
