I originally made this Field Test Review Video a few months ago but had to pull it down because it featured two WE Products. The WE AK74-UN and the WE G18C which unfortunately looks a bit like a Glock. If you are not familiar with the video I made on the Glock Trademark Infringement Cease Order I received then you should probably watch that video, it will fill in some of the gaps on why I had to cut out the WE G18C portions from this video and repost it with only the parts that showcase the WE AK74-UN.
Anyways you can still read my Original Field Test Review post minus the video and photos of the WE G18C.
Trigger Pull: The trigger pull on the Umarex Steel Force CO2 BB Machine gun is single action only, so you will need to charge the rifle by pulling back the charging handle first, one this is done the trigger is reset and ready the gun is ready to shoot. The blowback operation charges the internal bolt automatically afterwards so keep this in mind, to release the bolt you will need to take out the CO2 magazine and press the trigger. The trigger is fairly light but has some initial take up and then a bit of creep before it releases the bolt.
Accuracy: I shot the Umarex Steel Force at a target from 30 feet away in a semi rested position using both the semi auto and 6 round burst modes, the Steel Force performed very good getting around a 1.5 inch 10 shot grouping in semi auto and then spreading out a bit in 6 round burst mode which was to be expected, still a respectable grouping. Shots where well centered on the target but I did have the advantage of using a red dot scope, I found when using the none adjustable open sights that come with the Umarex Steel Force that I was shooting under the target at closer ranges. My Chrony testing did not go exactly as planned due to my temperamental Chronograph but I was able to get two shots to read and they average out at 466 fps, well over the 430 claimed fps.
Build Quality: The Umarex Steel Force CO2 BB Rifle is mostly plastic on the outside with most of it's metal parts on the inside, you will find a metal flash hider, metal trigger and metal trigger guard but other than that everything else externally is plastic. The plastic seems durable enough but it has just a bit too much shine for me which I think makes it look less like metal and more like plastic. Everything seemed to function as expected but again I would have liked to have seen a bit more metal, not necessarily the outer shell, but I feel the selector switch, sights, magazine release, charging handle and front and back sights could have been made out of metal and would have given this Umarex rifle a bit more weight and balance.
Realism: The Umarex Steel Force CO2 BB Rifle is designed on the AR platform and for the most part is about the right size shape and look of an AR pr M16 rifle. Even the selector switch, magazine release, rear adjustable stock and Charging handle function just like a real AR! Some parts are model in just for looks like the bolt release, dust cover and forward assist but at least they fully look the part. The plastic for me was the real tell here as it kind of looks like plastic where as some plastic guns are really hard to tell they are not metal, but other than that this is a pretty decent replica of an AR Rifle.
Good accuracy in both semi and 6 round burst mode.
Got lots of shots per dual CO2 (Full Hopper).
Love the adjustable AR stock which was missing and needed on the Steel Storm.
Not a bad replica of an AR platform gun.
Full auto has a very high rate of fire.
Internal blowback does give a bit of recoil feedback feel.
Lots of rials for adding on accessories.
Price point is good for a fun dull auto BB rifle.
Cons:
Sights are non adjustable.
Plastic finish could have been a bit higher grade, like what most Airsoft AR's use.
Just a bit more metal would have been nice and added to the overall weight a bit: Selector, Magazine Release, Sights, Charging handle.
Comments:
The Umarex Steel Force CO2 BB Machine Gun is for sure an improvement over the Steel Storm, first of all it is a true replica of a real rifle in production (The AR/M16 platform), it also has a rear stock that is adjustable which makes shooting this gun on target so much more easier. Overall I feel it shoots better than the Steel Storm with improved accuracy and performance. With that said the Steel Storm is still a great BB machine gun if your looking for more of a pistol SMG design. For the low cost of the Steel Force you really can not go wrong, this BB machine gun will put a smile on your face every time you take it out to shoot it.
My Vimeo Table Top and Field Test Videos for the Umarex Steel Force BB Machine Gun:
I have some more anticipated items from Umarex to show you all, and a special thanks to Bradley from Umarex for sending them my way to review.
If you like the Steel Storm then you should for sure like the Umarex Steel Force, both models share some basic mechanical attributes like semi auto and 6 round burst blowback operation, duel 12 gram CO2 cartridges, 300 round BB hoppers and 30 round spring fed magazines. The Steel Force however is more of a "replica" as it is modeled on the AR platform including an adjustable rear stock which will come in handy taming the high rate of fire 6 round burst mode.
Next up from Umarex is a classic replica of the Luger P08, it's always nice to see some older classics made into BB shooters, it may be the only way some of us will get to experience them and from what I can tell, the Umarex Legends P08 is near spot on! You won't find blowback or even a lot of actual moving parts other than the trigger, the safety and magazine release but this BB gun is all metal and well built, it has a nice weight to it with a firm double action trigger.
My last review item is not a gun but rather a gun accessory, the Umarex T.A.C. Converter which transforms several Umarex pistols into tactical PDW's. The actual models supported are the: HK USP, S&W MP40, X.B.G, CZ Enforcer, Walther P99 DOA and the now retired Umarex SA 177. With the T.A.C. Converter wrapped around your pistol of choice you are all setup with a folding stock and foregrip, not to mention anything else you may want to add onto the rails.
Keep posted for my full reviews of these items from Umarex.
Watch my Vimeo Update Video for these Umarex Products:
All references, photos and video claiming that any item in this review/video looks like a Glock or is a Replica of a Glock in any way shape or form have been removed from this post as requested by Glock "Renzulli Law Firm"
I almost forgot to do my field test review for my WE AK-74UN & WE G18C Tactical GBB Airsoft Pistol and Rifle! I decided to do them both together on this one but I still did my usual full testing for both guns which consisted of my Chronograph, Target and Can destruction along with some high speed slow motion of the blowback action of both guns in full auto mode.
Photo of WE G18C Removed by Request from Glock "Renzulli Law Firm"
Your best bet is to watch my Youtube video and see how both of these WE Airsoft guns perform. Overall they are both rally nice and super realistic, the WE G18C Tactical is definitely the full auto monster here while the AK-74UN is the bull in the China store with its crazy heavy blowback action, it has so much recoil that when shooting in full auto it kind of runs our of steam near the end, not so with the WE G18C as it did not slow down even with the 50 round magazine loaded up!
The WE AK-74UN even with it's crazy recoil holds on target very well in semi and full auto and of course has the superior fps performance. I found when shooting the G18C in full auto, I needed to hold my aim-point low as the blowback and super fast cycle rate wanted to pull the gun up and over my target, same would be true with a real gun so no surprise here.
Photo of WE G18C Removed by Request from Glock "Renzulli Law Firm"
FPS: 750 with Pellets and 800 with BB's for the US version (Up to 495 with Canada version).
Trigger Pull: The trigger pull on the Crosman MK-177 is medium length and fairly light. The trigger mainly releases the bolt so no pre-cocking of the trigger is required. The trigger is plastic but seems to work just fine as there is no real load on the trigger when shooting, you do need to get used to where the release point since there is some take up well before the trigger releases.
Accuracy: I found the Crosman MK-177 Air Rifle to be a very good shooter, getting about a 1 inch 10 shot grouping from 30 feet out in a semi rested position (sand bag up front, standing in the back). I also put 3 rounds through my somewhat failing Chrony Chronograph using 3,5 & 10 pumps and the MK-177 with the maximum 10 pump shot as high as 631 fps using 6.9 grain RWS lead pellets. I would expect the Canadian detuned version to shoot well below the 500 fps Canada limit much like my Canadian Crosman M4-177 I reviewed a while back.
Build Quality: The Crosman MK-177 Multi-pump Air Rifle is mostly molded plastic, but for a $100-ish Military Styled Replica Air Rifle it hits the mark in terms of affordability and if it was an all metal airgun you would more than likely expect to double or tripple this price point! Even though plastic is used throughout this Air Rifle, there are some internal metal parts where they need to be, the fit and finish seems to be good and I do not get the feeling the Crosman MK-177 is cheaply made in any way. The fact that most parts are molded means there is very little that can snap or break off and will make this air rifle even more durable longterm.
Realism: The Crosman MK-177 is a lose replica or copy of an FN SCAR Assault Rifle or ACR. It is not exact in terms of true dimensions to accommodate the pumping mechanism, You will not find very many working parts as just about everything is molded into the plastic on this Crosman MK-177 rifle. Unlike the Crosman M4-177 the lower magazine area is not removable and the rear stock is also none adjustable, I am not sure why Crosman didn't add these features to the MK-177 like they did to the M4-177? I am glad to see another Replica Assault rifle on the market as so few of them are available in Pellet or steel BB shooters.
None red dot version comes with detachable and adjustable iron sights.
Rails on top and sides for accessories.
Option of shooting pellets or BB's, I would stick to pellets and save the barrel since it is not semi auto.
Feels super solid since there are very few moving parts that could break.
Looks like the Crosman M4-177 Pellet magazines are compatible.
Cons:
Mostly plastic and just about everything is molded into the gun.
Bolt and magazine are on opposite sides?
Would of been cool if Crosman made a dedicated BB magazine?
Comments:
The Crosman MK-177 Multi-Pump Pellet/BB Air Rifle is very much like it's brother the Crosman M4-177 with a few plusses and a few minuses when comparing the two of them together. On the plus side the MK-177 has a bit more power and also the pumping is much easier while yielding higher internal pressures. On the downside the Crosman MK-177 is almost entirely molded plastic with no removable lower magazine or adjustable stock, and the bolt has been switched around to what I feel is the wrong side since now you need to index the magazine on one side and work the bolt on the other requiring a less efficient approach. Either way it is nice to have another replica air rifle on the marker and for the relatively low price you get a nice accurate pellet rifle, great for target shooting and even small pest control.
Watch my Vimeo Full Video Review of the Crosman MK-177 Pellet/BB Air Rifle:
We have added some items to the Canada and US Replica Airguns Stores, most are completely new items and one is a Canada only item we added to the US store!
I wanted to cover some basic Airgun, Airsoft Gun, Blank Gun and Paintball Gun information on what do they all shoot, what makes them shoot and some other miscellaneous info thrown in along the way...
Your should also watch the video attached at the bottom of this post as it goes into a fair amount of detail.
Let's begin with the types of ammo used:
Airgun Ammo
Airgun ammo for the most part is broken down into BBs and Pellets, the most standard size BB and Pellet is the 4.5mm or .177 caliber Steel BB and Lead Pellet. You can also get Pellets in other calibers and even other materials other than lead such as steel or aluminum, some can have plastic skirting around a metal interior.
Pellets also come in a variety of caliber's like .177, .20. 22. 25 and even larger but then I would start considering them to be bullets as they will take on the shape of a bullet when they get into the larger sizes.
Airgun Ammo is not be fired at people, it is primarily used for target and hunting small game.
Airguns can use Spring Pistons, CO2, Compressed Air and Multi-pump propulsion systems.
Airsoft Gun Ammo
Airsoft Guns for the most part shoot round 6mm (.22 caliber) plastic BBs which come in a variety of weights ranging from .12 grams up to .48 grams. There are larger Airsoft BBs such as 8mm and even larger.
There are biodegradable and even tracer florescent Airsoft BBs available.
Airsoft Ammo is traditionally used for Airsoft battles and can be fired at people using protective gear. Airsoft Ammo can also be used for target shooting.
Airsoft Guns can use Spring Pistons, Spring Piston - AEG (Electric Motor) CO2, Gas (Green, Red, Propane) and Compressed Air propulsion systems.
Paintball Gun Ammo
Paintball Guns or "Markers" have been historically used for the sport of Paintball but their whereabouts came from the need of ranchers and forestry workers to mark trees. Hence the name "Marker"
Paintball ammo comes in a variety of sizes ranging with the most common being .43 and .68 caliber. They are generally made from a gelatin outer coating containing primarily polyethylene glycol, other non-toxic and water-soluble substances, and dye, they are usually biodegradable.
Paintball Guns can also shoot a variety of Paintball Ammo that can be made out of Rubber, Plastic, Glass and they can also contain Powders and even Pepper for use in non lethal defense.
Paintball Guns can generally use either CO2 or Compressed Air as their propellant.
Blank Gun Ammo
Blank Guns are just like Real Guns but without the dangerous bullet at the end of the brass shell. Other than that they work exactly the same as a Real Gun!
Blank Guns are used when a bullet is not required or even wanted. For instance... Gun safety, gun training, training animals to be around guns and/or loud noises, Props for Movies - Stage - Film - TV, Collectors that do not want the red tape associated with owning a Real Gun or when owning a Real Gun is prohibited.
Blank Guns can shoot a variety of sized ammo, most common are .22 caliber crimped, .380 crimped, 8mm P.A.K. and 9mm P.A.K.
Blank Guns use gun powder as their means of operation.
Here are the most common forms of propulsion used in the guns we discussed earlier:
CO2
CO2 is the most common propellant in Airguns (BB and Pellet), it is also used in Airsoft Guns and Paintball Guns.
CO2 is a compressed gas which expands when released, it requires a warm environment to fully expand and tends to cool it's surroundings quickly when shot fast or in full automatic which can slow the velocity of the projectile and even freeze up the gun being used.
The most common reusable CO2 cartridges are 12 and 88 gram but you can get larger CO2 tanks in a variety of sizes that can be refilled with CO2.
Gas
Gas is used primarily in Airsoft Guns, I have not personally seen an Airgun that is made to use Gas other than CO2.
Gas is similar to CO2 in that it is a compressed gas that expands when releases, it also cools down the gun it is being used in and requires a warm environment.
Gas comes in a variety of names, Green Gas, Red Gas and Propane Gas. Green Gas contains Propane as it's base but has additives in it like silicone for lubrication .
Red Gas is know to be a bit more powerful than Green Gas as it has Chlorodifluoromethane or HCFC-22, R22 or Freon 22 used in refrigeration which turns to a liquid under a slightly higher pressure giving you slightly higher fps.
Many people use propane gas with an adapter that allows the mixture of silicone as propane is cheaper to buy.
Compressed Air (HPA)
Compressed Air (HPA - High Pressure Air) is most commonly used in Airguns and Paintball Guns but some people use it for their Gas based Airsoft guns.
The compressed air comes from high PSI tanks that can be purchased in a variety of sizes and contains compressed air at pressures up to 5000psi.
These tanks are reusable and usually need to be refilled at a paintball or scuba shop, some people buy their own compressors or large scuba tanks for refilling purposes.
Some Compressed Air (HPA) guns have their own built in tanks that can be filled with a compressor or even a manual pump.
Compressed air does not cool down the gun it is being used in and is a great option for high output or fully automatic guns.
Multi-Pump Pneumatic
Multi-Pump Pneumatic systems are most commonly used in Pellet and/or BB guns.
Multi-Pump Pneumatic guns use the same principle as HPA - High Pressure Air guns in that they require pressurized air as the propellant. The main difference with Multi-Pump Pneumatic guns, is that you do all the work by pumping the gun between shots. Generally speaking you pump the gun 3-10 times, take a shot and repeat this process.
Multi-Pump Pneumatic guns are not effected by air temperature and are great for target and small pest control.
Spring Piston
Spring pistons are generally found in Pellet Rifles and Pistols but some Airsoft Guns also use a Spring Piston System and generally speaking Spring Piston Guns are single shot only or in other words, the Spring needs to be drawn back before each shot. Spring Piston Guns can have magazines that allow for quicker repeat shots.
Spring Piston Guns come in many cocking configurations, Brake Barrel and Side lever to name a couple.
The Spring can be a Mechanical Spring or a Gas Spring.
Spring Piston Guns are not effected by temperature and are often used for small game hunting and target shooting.
Automatic Electric Guns (AEG)
Automatic Electric Guns are generally found in Airsoft Rifles but there are some Airsoft Pistols (AEP) that use this same system.
Automatic Electric Guns use a similar system to a Spring Piston gun but have an electric motor that does all the work of drawing back the spring. You can even have fully automatic AEG guns.
The power for the electric motor comes from removable batteries, so it is a combination a battery supplying the motor with the power to draw back the spring that creates a pillow of air that shoots the BB.
AEG Airsoft Guns are great for situations when you require high capacity magazines with full auto capability.
Gun Powder
Gun powder is used in Blank Guns, in the same manor that it is used in a Real Gun, the charge from the Gun Powder supplies the force required to operate the blowback in most semi auto Blank Pistols, it also creates the sound of a live round along with the muzzle flash which makes Blank Guns great for training and as Props for Movies and Film.
Because the kinetic energy from a blank gun is the same as a real gun, blank guns can be very dangerous when used in close proximity to an object, see my "Are Blank Guns Dangerous Video"!
Some other Gun Relevant Terminology:
Blowback
Blowback operation is when some of the force of the propellant is used to move the slide backwards, which in most cases cocks the hammer for single action and can also pickup and chamber a round into the barrel.
The slide spring supplies the energy for the return to the forward position of the slide.
Blowback Guns do rob some power from the bullet force and in the case of CO2 or Gas Guns the also reduce the amount of shots per CO2 or Gas fill.
Revolver, Semi Automatic
Revolver: Revolvers feed ammunition via the rotation of a cartridge-filled cylinder, in which each cartridge is contained in its own ignition chamber, and is sequentially brought into alignment with the weapon's barrel by a mechanism linked to the weapon's trigger (double-action) or its hammer (single-action)
Semi Automatic: semi-automatic pistols use the energy of one shot to reload the chamber for the next. Typically recoil energy from a fired round is mechanically harnessed. After a round is fired, the pistol will cycle, ejecting the spent casing and chambering a new round from the magazine, allowing another shot to take place immediately.
Single Shot, Repeater, Semi Automatic & Fully Automatic
Single Shot: A Single Shot Gun needs to be reloaded each time it is shot.
Repeater: Repeating action Guns are single barreled guns containing multiple rounds of ammunition. These rounds are loaded from a magazine by means of a manual or automatic mechanism, and the action that reloads the rifle also typically re-cocks the firing action. The term repeating rifle is most often applied to weapons in which the next cartridge is loaded by a manual action, as opposed to semi-automatic rifles, in which the force of one shot is used to load the next.
Semi Automatic: A semi-automatic, or self-loading, firearm is a weapon that performs all steps necessary to prepare the weapon to fire again after firing.
Fully Automatic: A Gun that uses either its recoil or a portion of the gas propelling the projectile to remove the spent cartridge (in the case of a gun-shell), fire again repeatedly, as long as the trigger is held down or until the magazine is exhausted. Automatic Guns are distinguished from semi-automatic Guns in their ability to fire more than one shot in succession once the trigger is pulled.
Single-Action (SA): trigger performs the single action of releasing the hammer or striker to discharge the firearm each time the trigger is pulled.
Double-Action (DA): The trigger both cocks and releases the hammer or striker
SA-DA: A SA/DA firearm combines the features of both mechanisms. You can pull the trigger in Double Action when the hammer is down which cocks and releases the trigger or you can cock the hammer with your thumb and then release the trigger using Single Action to fire the weapon.
Lever Action, Pump Action, Bolt Action
Lever Action: In a classic lever-action firearm, rounds are individually loaded into a tubular magazine parallel to and below the barrel. A short bolt is held in place with an over center toggle action. Once closed, the over center action prevents opening solely by the force on the bolt when the weapon is fired. This toggle action is operated by a hand grip that forms part of the trigger guard. When operated, a spring in the tubular magazine pushes a fresh round into position. Returning the operating lever to the home position chambers the round and closes the breach.
Pump Action: With a pump-action firearm, the action is operated by a movable fore-end that goes backwards and forwards to eject, extract, and chamber a round of ammunition. Pump-actions are usually associated with shotguns.
Bolt Action: The bolt opens and closes the breech end of the barrel and contains the firing pin. The bolt is held in place with a lever that fits into a notch. Moving this lever out of the notch will release the restraint on the bolt, allowing it to be drawn back. An extractor removes the spent cartridge, which is then ejected through the lever slot. A spring at the bottom of the magazine pushes up the reserve rounds, positioning the topmost between the bolt and the chamber at the base of the barrel. Pushing the bolt lever forward chambers this round and pushing the lever into the notch locks the bolt and enables the trigger mechanism.
Magazine vs Clip
Magazine: A magazine is an ammunition storage and feeding device within or attached to a repeating firearm. Magazines can be removable (detachable) or integral to the firearm. The magazine functions by moving the cartridges stored in the magazine into a position where they may be loaded into the chamber by the action of the firearm. The detachable magazine is often referred to as a clip, although this is technically inaccurate.
Clip: A clip is a device that is used to store multiple rounds of ammunition together as a unit, ready for insertion into the magazine or cylinder of a firearm. This speeds up the process of loading and reloading the firearm as several rounds can be loaded at once, rather than one round being loaded at a time. The term "clip" is also frequently used to refer to a detachable magazine, though such usage is incorrect.
I wanted to show off a few new items that I will be reviewing, one being the Crosman MK-177 Pellet and BB pneumatic multi-pump air rifle that was very graciously provided to me by Crosman for review. And the other item is something kind of new in terms of the type of gun, since it is not really gun but rather a bow, or crossbow to be exact. We hope to be adding to our Replica Airguns Store a couple variations of the Avalanche Trailblazer 150lb Crossbows in wood stock and polymer stock versions.
Here are a couple key points about each item being looked at in this update video and then I will leave you with some detailed photos to drool over and of course my YouTube Update Video to watch...
Crosman MK-177 multi-pump bolt action .177 caliber BB/pellet air rifle:
Shoots both .177 caliber pellets and 4.5mm Steel BB's
Maximum 800 FPS (US Version being reviewed here)
5 shot pellet magazine and 300+ BB reservoir
Multi-pump single shot bolt action
3-10 pumps per shot
16.75 inch rifled barrel
3.5 pounds
Mostly plastic with some internal metal parts
Avalanche Trailblazer 150lb Crossbow with Wood Stock:
Trigger Pull: The trigger pull on the WE AK74UN GBB Airsoft Rifle is very light (maybe even under 1 pound) since the blowback action has already pre-cocking the action making this rifle single action only. The take-up is very short, about one eighth of an inch or even less! The magazine has two switches, the one on the top allows you to dry fire while the one on the backside resets the trigger block. You will need to push the side switch down after reloading your magazine to allow the trigger/hammer to function again.
Accuracy: Out of the box the WE AK74UN Airsoft Rifle shot on the high side for me, about 8 inches at 30 feet, you can adjust the front sight post to some degree for elevation but I was not able to find any way of adjusting the windage? I did my pretest shooting from the 30 foot mark and I found the WE AK74UN Gas Blowback Airsoft Rifle AK74 Replica shot a very respectable 5 shot 1.5 inch group in semi auto which opened up of course when I shot the rest of the rounds in full auto. The full auto group stayed pretty tight considering all the recoil that was going on. I would say this gun should be able to shoot fairly accurately at distances even greater than 50 feet and even in full auto.
Build Quality: The WE AK74UN Airsoft Rifle is very well made with a lot of actual stamped steel parts, the only metal (zinc alloy) would be the trigger group, bolt, and part of the front sight, the pistol grip and front stock are made out of a matt finished hard plastic. Fit and finish is near perfect and I had no problems with the functionality of this Airsoft replica in any way. There are third party steel replacement parts for the trigger group and bolt if you want to swap these out at some point.
Realism: Everything about this gun is realistic! Operation, field stripping, tones of steel and metal parts, the long travel bolt, the slower cycle rate, and the heavy recoil all make the WE AK74UN GBB Airsoft Rifle as near perfect a working replica that you can find. Sure WE modernized this AK74 variant a bit with the addition of some enhancements but they do work well and make this Airsoft rifle very usable.
Long travel bolt with heavy blowback, lower cycle rate like a real AK!
Lots of steel and metal in this gun, very hefty and solid.
Awesome blowback kick really hits you in the shoulder.
Semi auto & full auto selectable.
Field strips just like the real AK.
Nice high 400+ FPS and good 1.5 inch 5 shot group from 30 feet away.
Decent use of Gas.
Modified improved selector/safety switch can be used with trigger finger and also can be used to lock the bolt back for easy hop-up adjustments.
Magwell guide helps with insertion of the magazine.
Cons:
Long travel bolt kicks so hard that it can wear the softer Zinc Alloy internal parts quickly like the bolt and trigger grouping.
Sights are not really very adjustable, at least for windage.
Comments:
I really love my WE AK74UN Gas Blowback Airsoft Rifle, it is truly one of the most realistic replica guns I own, not just in looks but in how it functions and shoots. The heavy use of stamped steel, lots of metal throughout, full travel bolt with heavy blowback and realistic AK cycle rate make this one of the most fun guns to shoot that I own. If you're looking for a Gas Blowback AK styled Airsoft rifle this one is one of the best out there!
My Vimeo Table Top Video REVIEW of the WE AK74UN Gas Blowback Airsoft Rifle:
I have a couple of guns I wanted to share with you all and no we do not sell them at this point in time and I can not say if we will or not down the road.
There is just no way we can carry every brand of gun and every gun from every brand, that said I still sometimes have my eye on a gun and will pick it up even if I have to pay full retail juts so I can add it to my collection and also do a review for all of you.
Photo of WE G18C Removed by Request from Glock "Renzulli Law Firm"
Today I showcase two Gas Blowback Airsoft guns from WE. I have been wanting to get an AK variant of some sort since there was a big whole in my collection after the RCMP came into my house and took my scary AK BB gun away. And if for some reason you feel this "again" legally imported through the CBSA non convertible airgun is in some way a concern, please feel free to come on over and have a good look, no SWAT team necessary this time. I am just around the corner from the police station and I make a good cup of coffee!
Getting back to this update, the other WE Airsoft gun is the WE G18C which like the WE AK74UN, also has semi and full auto select-ability. Both guns have excellent blowback kick with the AK74UN having a full travel blot which kicks like a mule and has a slower full auto cycle rate much like a real AK47.
Both guns have metal parts where you would find them on the real steel versions while the AK even goes so far to have actual stamped steel all over just like you would find on an AK.
Photo of WE G18C Removed by Request from Glock "Renzulli Law Firm"
I will be doing full reviews for both these WE GBB Airsoft guns so stay posted for those video reviews, in the meantime you can watch my Update Video showcasing both these WE Airsoft guns.
The rainy weather let up today so I grabbed up my Umarex - KWA MP7 Blowback Airsoft PDW and put it through its paces today. I was a bit surprised that my groupings from 30 feet away shooting from a semi-rested position where a bit spread out, mostly top to bottom. Perhaps the hop up was effecting the MP7? The good news is that shooting in full auto did not seem to make things any worse :) I was using .25 gram BB's for the accuracy test.
As for the Chronograph portion of this field test shooting review, the Umarex - KWA MP7 Blowback Airsoft Machine Pistol shot a bit higher than claimed at just over 400 fps using .20 gram BB's with Propane Gas. I had no problems shooting a full magazine of 40 rounds with a full gas fill up and the cycle rate stayed nice and high with very little cool down effect.
I really enjoyed shooting the Umarex - KWA MP7 Blowback Airsoft PDW, it has a nice sound with just the right amount of blowback to give it a good feel without throwing off the sights, the trigger was very light and responsive and I ended up preferring to use the pop up sights over the pistol sights as I was shooting mostly with the stock and fore grip open. Those Cans never had a chance!
All in all the Umarex - KWA MP7 Blowback Airsoft PDW is one of the coolest compact and ultra modern Airsoft guns I have had the pleasure to review and test out.
Watch my Field Test Shooting Vimeo Video for the Umarex - KWA MP7 Blowback Airsoft PDW:
I had a chance today to get out and shoot my B&W Dragunova SVD Airsoft Sniper Rifle, the weather held out just long enough for me to setup my target a good 90-100 feet out in the field but as luck would have it, it started to rain on my camera gear right as I started doing my target shooting test using .36 gram Airsoft BB's. So in a bit of a rush, I shot off a good 10 rounds and was able to put most of them on the paper which from 100 feet out using an Airsoft rifle on a target the size of a standard 8x11 sheet of paper is not too bad at all, and don't forget I was just using the iron sights.
I found I didn't even need to use the hight adjustment on my rear sight as the hop-up seemed to keep the Airsoft BB's floating nicely on plane all the way to at least 100 feet. By the way if you watched my earlier Table Top Reviews I mentioned the B&W Dragunova SVD was shooting a bit to the left even after full windage adjustment to the right, well I managed to sort this out and pull the sight the little bit extra I needed to get it pretty much dead center.
Moving on to the Chronograph portion of this Field Test Shooting Review, I got the same results as my pretest with an average fps of 498 using .20 gram Airsoft BB's and an average fps of 277 using the heavier .36 gram BB's. I have heard that the B&W Dragunova SVD Airsoft Sniper Rifle can be a bit of a chore to cock but for me it was actually pretty easy and using a left overhand approach worked well, allowing me to cock the charging handle pretty easy while keeping my finger on the trigger and the rifle in position ready for my next shot.
The iron sights and the trigger setup seem to both work very well with this rifle, I really have no real complaints and really enjoyed shooting the B&W Dragunova SVD Airsoft Sniper Rifle. If the rain hadn't been coming down on my camera gear I may have put a bunch more shots into the target for the simple reason I was having so much fun :)
Watch my Field Test Shooting YouTube Video for the B&W Dragunova SVD Airsoft Sniper Rifle:
Trigger Pull: The trigger pull on the B&W Dragunova SVD Airsoft Sniper Rifle is good overall, just a bit of initial take-up and then a medium trigger pull to release the heavy spring. You will of course nee to pull the charging handle with each shot to preload the spring.
Accuracy: My initial accuracy testing was done from about 45-50 out using .36 gram Airsoft BB's, it was a fairly windy day but even so I was able to get a nice tight 2 inch grouping using a semi rested position. I also put the Dragunova SVD through my Chronograph testing and shot both the lighter .20 gram and heavier .36 gram BB's to see what kind of fps I would get using both weights. The lighter .20 gram BB's got right around 500 fps while the heavier .36 gram BB's shot a bit lower at approximately 380 fps. I did however find that sighting the SVD in for windage adjustments (left and right) was a bit of a challenge as you can only adjust the front sight by loosening it with an allen key and make only very slight left to right adjustments. I was not able to get the SVD to shoot far enough to the right using this method so I amy need to do figure something else out, perhaps a scope setup?
Build Quality: The B&W Dragunova SVD Airsoft Sniper Rifle is not a super expensive rifle but still has a good combination of metal and plastic components. Most of the parts that you would find on the real SVD are metal including the barrel, bolt/charging handle & receiver, trigger, magazine, sights, strap rings and rial system. The stock is of course plastic with some added rubber. The B&W Dragunova SVD is not overly heavy but still has a reasonable amount of weight to make it believable. Performance was very good with no mechanical problems other than the last two BB's in each magazine do not load into the rifle.
Realism: I have never held an actual Dragunova SVD in my hands but from what I have seen in photos, it looks to be a good copy of the real steel Russian sniper rifle. Lots of metal helps pull of the realism, a working charging handle, removable bolt cover, and lots of other working components make for a believable looking and functioning version of this Airsoft BB shooting Dragunova SVD Sniper Rifle.
Lots of metal parts throughout where they would be on the real SVD.
Good power and accuracy combination.
Fairly high capacity magazine at 40 rounds.
Sights are adjustable for elevation front and back and a bit for windage.
Bolt is surprisingly easy enough to cock with either left or right hand.
Lots of upgrades available for this sniper rifle.
Inexpensive way to own a piece of history.
Cons:
Some discrepancies in the manual (180 fps and 100 round magazine)
Sighting for windage may not be adequate?
Would definitely be much nicer with the wood stocks.
Two BB's always pop out of the magazine area when empty.
Comments:
I found the B&W Dragunova SVD Airsoft Sniper Rifle to be a lot of fun to shoot, I was not sure how the charging handle system was going to work in terms of weight and easy of use to pull it back. I ended up using my left hand and reaching across and over and surprisingly this was very efficient and effective in charging the spring and allowed me to keep my righthand in place and on the trigger for very quick follow up shots. Power was as much as you would want from a sniper rifle and accuracy was also very good even in windy conditions. The only real problems I had where the two BB's that did not load from each magazine and the windage adjustments not quite allowing me to move my aim point enough for a bullseye at 50 feet out. I would recommend this B&W Dragunova SVD Airsoft Sniper Rifle and would suggest possibly adding some wood stocks and a magnified scope setup.
After many many requests to show how the Umarex Walther PPK CO2 Tab Modification is done I have relented to public demand. I don't actually cut my tab in this PPK CO2 Tab Modification Video but I do go step-by-step in detail and compare my modified Umarex PPK to my unmodified Umarex PPK. It is really very basic on how this is done and only a hack say and perhaps a file are all that is required to make the modifications to the PPK CO2 tab in order to make it flush with the bottom of the handle area.
Your best bet is to simply watch my YouTube Video located below and follow the steps there but here it is in text form:
Place an empty (already pierced) CO2 into your Umarex Walther PPK and tighten the unmodified CO2 tab until fully tightened, just like you would tighten a fresh CO2.
Take note at how many threads are exposed between the bottom of the handle and the top of the plastic CO2 tab, there should be about 2-4 threads exposed.
Unscrew the CO2 tab all the way, place the PPK BB Pistol so it is secure (in a vice of some sort) and use a hacksaw or dremel to shorten the CO2 screw just above the plastic tab at the thread location you previously noted. Be conservative as you can always cut or file the screw a bit shorter if your first cut was not short enough.
Now use the same hacksaw or dremel to cut a notch in the exposed cut area of the CO2 screw so that you can use a slot screwdriver to tighten the CO2 screw.
That's it - Enjoy your modified Umarex Walther PPK CO2 BB Pistol!
Watch my Vimeo Video of the Umarex Walther PPK CO2 Tab Modification Tutorial:
Ammunition Capacity: 13 round full size metal magazine -18 round metal stick magazine.
FPS: 428 - 380.
Trigger Pull: There is a lot of difference between the trigger on both of these guns, first off the Umarex Makarov has both a single and double action trigger/hammer while the KWC Makarov has a double action only trigger/hammer. Comparing the double action of both guns the definite advantage goes to the 4.5mm Steel BB shooting Umarex Makarov as it is shorter and lighter, the KWC Airsoft Makarov does not have a bad trigger but it is much longer and a bit heavier, but still very usable. The single action trigger on the Umarex Makarov is not really any lighter than when shooting in double action, it is however much shorter with a medium take-up and predictable release.
Accuracy: Both Airsoft and BB Makarov's performed very well in their shooting tests for me, they bot shot fairly well centered with the KWC Makarov getting all five shots in the black bullseye and the Umarex Makarov having a tighter group but just off to one side. This was good news since both guns do not have adjustable sights! They also scored very well in the velocity department shooting over their advertised claimed feet per second rating. The Umarex BB version shot a very respectable 390 fps while the KWC Airsoft pistol shot a very surprising 480 fps well over the claimed factory 430 fps. Both guns also shot very accurately out to ranges of 50 feet or so. From a single CO2 I was able to get 162 shots from the Umarex Makarov and 112 shots from the KWC Makarov before I noticed a significant power drop.
Build Quality: Neither one these Makarov replicas is going to win a prize for build quality, some shortcuts have been made to keep the price down on each model, but they are both built with mostly metal parts and they both performed perfectly for me during my testing. The Umarex 4.5mm Steel BB Makarov did have more moving parts while the KWC did weigh in a bit heavier, both guns had reasonable fit and finish to them.
Realism: In terms of being good Makarov replicas the pair for sure look the part, size and overall weight are very true to the original real Steel Makarov PM with the Umarex Makarov having a working slide, Makarov licensing and the ability to be field stripped. The KWC Makarov had a nicer recessed barrel and full size drop out metal magazine. I was not a big fan of the KWC screws on the right side slide or the Umarex exposed CO2 tab.
KWC may shoot a bit too hot for CQB Airsoft games.
Both guns do not have adjustable sights.
Comments:
To be honest when I got the KWC Airsoft BB shooting Makarov, I was not all that awe struck, the lack of a working slide, DOA trigger and screw holes in the slide put me off just a bit. This Airsoft pistol did warm up to me a lot once I shot it, I was surprised by the very high fps and how accurate it was for such a low cost Airsoft pistol. I can really see this gun being used as a backup or sidearm in an out doors style Airsoft game where you may need to shoot targets out at range where other lower powered pistols just would not be able to get out to. The Umarex Makarov has always had a place in my heart, it is just a really good little CO2 BB pistol for the price with mostly all metal parts, a working slide, single and double action trigger and very good overall performance. In my books you can not go wrong choosing either of these Makarov replicas so choose wisely!
My Vimeo Video Table Top Comparison Review for these Makarov Air Replicas:
This is not meant to be a full review of either the BB or Airsoft version of the Cybergun - KWC CO2 Blowback Mini UZI's but I do talk about specifications, show you around both guns, and put them both through a full Field Test so I guess in a way, perhaps it can be considered to be a full review ;)
I will list the specifications here for you but I am not going to get into details like Trigger Pull, Build Quality, Accuracy and Realism. You can check out my other video reviews for more information on the Mini UZI:
As I said you can check out all my other videos for info on these very accurate Mini UZI Replicas, I mainly want to go over some of the main differences and similarities for both the BB and Airsoft versions.
In terms of build quality they are made almost exactly the same and weigh in at a hefty near 5 pounds, the only differences are the inner barrel and magazines to accommodate the different sized ammo. The BB version has a 25 round single stack magazine that does not have a follower to stop the bolt from continuing to operate even after the magazine is empty. While the 6mm Airsoft version has a double stack magazine that holds 38 rounds and does have a follower to stop the bolt which can save you some unintentional wasted CO2.
The Airsoft Mini UZI version is distributed by KWC while the 4.5mm BB version is distributed by Cybergun, you will find the UZI and IWI licensing on the Cybergun 4.5mm BB version but not on the KWC 6mm Airsoft version.
Out of the box the KWC Airsoft Mini UZI is ready to go in both semi auto and full auto while the 4.5mm steel BB version will only shoot in semi auto mode, it can however be easily modded to shoot in full auto.
Both guns come in cardboard boxes with manuals, some BB's and an Allen key to tighten the CO2. The KWC Airsoft Mini UZI also comes with a handy speed loader.
There is a slight fps velocity difference between the two with the KWC Airsoft 6mm plastic rounds traveling at around 400 fps (with .20 gram BB's) and the 4.5mm Steel BB's traveling at right around 350 fps. In the field test portion I test both guns out on some water filled cans to see how each ammo type performs in terms of penetration.
Your best bet is to watch both my Table Top and Field Test Comparison Video Reviews and see for yourself how they compare!
Earlier this week my father called me up and asked if I wanted to head out with him to go do some hunting/shooting. He has his bear tag but for the most part, hunting with my Dad consists of driving around in his truck hoping to stumble on something since he can not walk all that far these days.
We had a great time just enjoying each others conversation and of course the beauty of Canada BC's Harrison Lake area. We also got to shoot some guns to "make sure they where sighted in and working correctly". I brought my Norinco 12 Gauge Homeland Security 780 which I needed to test out and I'm glad I did since it needs some TLC to get working smoothly. I also brought along my little Henry Lever Action 22LR which is always a blast to shoot. My Dad brought his Savage Arms 7mm Magnum just in case we did see a bear on this outing.
Long story short we didn't bring any meat back home with us but we did see some out of season doe and of course had some nice father-son time together...
I don't often get to shoot my airguns out at the 100 foot mark but I purchased my Sheridan Silver Streak .20 Caliber Multi Pump Pellet Rifle mainly to shoot up to and even past this fairly distant range as the Silver Streak is my new vermin gun for pests around the farm. I get a lot of Crows that to be honest are just feathered bullies that pick on all the other friendly birds on the farm, they have also been known to get into my garbage and even attack the Eagles and Hawks in the area. Flying Rats I like to call them.
In this Field test Shooting video I test out my brand new Sheridan Silver Streak on the Chronograph to see just how powerful it really is not just at the maximum 8 pumps but also at 3 and 5 pumps. I was actually very surprised at the very decent power I got from only 3 pumps (460 fps), you could easily take out a small rat with the 14.3 grain .20 caliber lead pellets I was using for my Chrony test. At 5 pumps I gained close to another 100 fps and at 8 pumps I maxed out at just a hair under 640 fps respectively. With the 14.3 grain pellets I was using this worked out to right around 13 foot pounds of energy. (My Sheridan was purchased using a PAL)
I also shot my Sheridan Silver Streak .20 Caliber Pellet Rifle at a target setup 100 feet or just over 30 yards away and was able to get what I felt was a nice 1.5 inch 5 shot grouping. 4 of the 5 pellets where all within 1 inch of each other with my first shot being a bit lower and to the right of the rest spreading the group out to about 1.5 inches. Keep in mind I was also a bit winded from all the pumping and I could feel and see my heartbeat in my 9 power Bushnell scope making my crosshairs bob back and forth ever so slightly.
I have not shot my Sheridan Silver Streak all that much and plan to hone my skills further so when the time comes I will be ready for them pesky crows.
Stay tuned for my future Table Top review of my Sheridan Silver Streak, for now you can checkout my Preview video that has some preliminary info.
For the most part, this video is to test out some cameras and using them all together in a multi-camera scenario. I wanted to see how many camera angles I could shoot at one time and see how they would all work together when editing the video.
Cameras used:
My new Pivothead Recon Camera Glasses.
Sony HDR-AS15 Action Cam.
Drift HD170 Point of View Camera.
Nikon 1 with 10mm fixed lens.
Casio TRYX.
*All cameras where shooting in 1080p for this video.
I hope to use camera setups like this in the future, maybe not all at once but at least a couple at a time to give you some viewing options.
I picked out my WE SCAR GBB Airsoft Rifle for this test as it had a lot of mounting points and the Gas Blow Back makes for some great video action. Unfortunately My WE SCAR was not working at 100% but I still think I was able to pull off this test video either way.
Watch my Multi-Camera-Angle Test Video shooting the WE SCAR GBB AIrsoft Rifle:
ALL GUNS ARE NOW SOLD - THANKS FOR THE AWESOME RESPONSE!
This is a first for me but I guess you could say I have to make room for some more guns ;) I have some duplicate guns and a couple I juts don't have a need for anymore so instead of having them sit around collecting dust, I thought I would offer them up for sale and get them in the hands of someone who can really appreciate and get some use out of them...
Here is a list of the items up for sale:
Baikal IZH-61 .177 Caliber Spring Piston Pellet Rifle: $115
Baikal MP-655K Pellet/BB CO2 Pistol (missing pellet magazine): $125
Umarex CP99 Compact CO2 BB Blowback Pistol: $50
Swiss Arms Sig Sauer GSR 1911 CO2 BB Pistol: $30
ASG CZ 75 P-07 DUTY Dual Tone CO2 BB Blowback Pistol: $125
Umarex Beretta M92FS .177 Caliber CO2 Pellet Pistol - Nickel with Wood Grips: $200
(2x) AK47 BB Gun Magazines: $50 Each
Crosman 2240 .22 Caliber CO2 Pellet Pistol (14 inch barrel, RJMachine Breach/Brass Bolt, Wood Grip, NcSTAR 6x32 Scope): $225
Shipping/Handling is $15 Canadian and $25 to the US and you must be 18 or over to buy. You will need to email me at mike@replicaairguns.com to let me know what gun/guns you want to buy - first come first serve, I will send a PayPal request to the person with the first offer to buy and give them 24 hours to pay or I move on to the next buyer.
You can watch my YouTube Video to get a good look at each pre-owned item up for sale:
