I was waiting for a magazine for my ASG STI Duty One 1911 to show up so I could finally do this "Head to Head" Field Test Shooting Review Video for the ASG STI Duty One versus the ASG CZ 75 P-07 Duty versus the ASG Bersa BP9cc. All of which are Blowback CO2 4.5mm Steel BB pistols.

This Shooting Field Test went fairly well and all guns performed as expected, I did have one slide lock back on a loaded magazine with my ASG STI Duty One 1911 and one failure to lock back on the last shot with my ASG Bersa BP9cc, but it did eventually lock back.

During the Chronograph 5 shot per pistol test I got fairly similar fps from all three guns with the STI Duty One getting the highest of 372 average fps, the Bersa BP9cc getting runner up with 353 average fps and the CZ 75 P-07 Duty trailing the field just a bit with a 346 average fps.

During the target portion of this Field Test Shooting Review from 30 feet back in a semi rested position, again the pistols shot fairly similarly with all of them getting pretty close to 2-3 inch groupings. I did have a double shot right after my slide lock back on the STI Duty One as I pressed the trigger twice, once when the slide was locked back and again when I released it, this chambered two BB's into the barrel making the gun shoot a bit low for that double shot. With that negative one against the STI Duty One 1911, I did however find it the most pleasing to shoot! It had the best blowback action and the smoothest trigger, plus I just like holding and sighting in 1911's :)

The CZ 75 P-07 had the next hardest blowback with the Bersa BP9cc coming in second in the trigger department. All of these CO2 blowback BB pistols should get somewhere around 100+ shots pre CO2 if you take your time a bit between reloading magazines.

Buy ASG BB Pistol From the Canada Store - Buy ASG BB Pistols from the US Store

I finally got some brand new Umarex pistols to share with you in this Vimeo video, all three of these CO2 4.5mm Steel BB pistols have blowback and use full size drop out magazines. They also all share single action only operation.

The Umarex Makarov Ultra (Legends Series) is an all metal pistol with very heavy blowback and a long but fairly smooth and medium pull single action trigger. Everything works just like the real steel version including the slide catch/release and safety. It is also fully field strip-able.

The Beretta 84 FS (Cheetah) also has a decent blowback feel but the trigger was a bit heavier on this model, perhaps the trigger will break in a bit over time? Still a really great full metal and fully licensed CO2 Blowback BB shooter with awesome weight to it. The Beretta 84 FS is fully field strip-able and has a working slide catch/release and safety.

Lastly I show you the Umarex Mauser C96 Boomhandle (Legends Series), although much of the external materials are plastic, there is lots of metal throughout like the barrel, bolt, rear sight, hammer, safety, trigger and most of the drop out magazine, giving this pistol a good overall weight to it. The blowback is super fast and crisp with a nice short and light single action trigger making rapid fire very quick.

Umarex Makarov Ultra CO2 Blowback 4.5mm BB Pistol 

• Full metal

• Blowback operation

• 4.5mm Steel BB

• 12 Gram CO2

• Single action only trigger

• Fixed sights

• 3.5 inch smooth bore barrel

• 1.4 pounds

• 16-17 round magazine

• 350 fps

Umarex Beretta Mod. 84 FS CO2 Blowback 4.5mm BB Pistol

• Full metal

• Blowback operation

• 4.5mm Steel BB

• 12 Gram CO2

• Single action only trigger

• Fixed sights

• 3.6 inch smooth bore barrel

• 1.5 pounds

• 16-17 round magazine

• 360 fps

Umarex C96 Mauser CO2 Blowback 4.5mm BB Pistol

• Metal & plastic

• Blowback operation

• 4.5mm Steel BB

• 12 Gram CO2

• Single action only trigger

• Adjustable rear sight

• 5.5 inch smooth bore barrel

• 1.8 pounds

• 19 round magazine

• 380 fps

Buy Umarex BB pistols in Canada - Buy Umarex BB pistols in the US

In this Comparison Video I go through the benefits and shortcomings of CO2, Spring Piston and Pump Airguns. I focus mainly on Airguns but there is a bit of a crossover with Airsoft guns.

All three systems (CO2, Spring, Pump) create pressure that forces the ammunition with a high force out of the barrel. Similar to how gun powder is the source of energy for a bullet.

Here are some basic statements that best describe CO2, Spring Piston and Pump Airguns.

CO2 Airguns:

• CO2 Airguns use the expansion of CO2 gas to create the pressure required for the ammo.

• CO2 Airguns generally store enough CO2 for multiple shots per cartridge.

• CO2 Airguns have a limit as to how much power they can produce since CO2 has a set vapor pressure of 850 psi, or about 56 bar at room temperature which is around 25 C or 77 F. CO2 Gas also requires a warm environment to expand so warmer temperature and longer barrels help with power.

• Some CO2 guns can also use pressurized air tanks in place of CO2.

Spring Piston Airguns:

• Spring Airguns use the release of a pre-cocked spring and plunger system to compress air to power the ammo.

• Spring Piston Airguns require the cocking of the spring between each shot so they are single shot only.

• Spring Airguns are limited to how much effort is humanly possible to cock the spring into position. If you make the spring to strong then not everyone will be able to use the Airgun effectively. Too week of a spring and the Airgun will lack power.

• Spring Piston Airguns are known for having a fair amount of recoil and vibration when the spring moves both forward and backwards quickly inside the Airgun.

• Spring Airguns can use either a mechanical spring or a gas spring.

Pump Airguns:

• Pump Airguns (either Single or Multi-Pump) store air pressure in a chamber that when released, powers the ammo.

• Most Pump Airguns require at least 1 or more pumps, often up to 10 pumps for each shot and you generally only get one shot per set of pumps. Not to be confused with PCP Airguns (Pre Charged Pneumatic) which have large pressure tanks that are recharged with a high volume of pressurized air that is capable of shooting multiple shots per charge.

• Pump Airguns are also somewhat limited to how much effort is humanly possible since the higher the chamber pressure, the harder it will be to pump the Airgun. 

Misc Airguns:

• Generally speaking both Spring and Multi-Pump Airguns have more potential power than a CO2 guns since CO2 has a set peek pressure limit.

• Pump and CO2 Airguns are know to have very little recoil since the pressure is stored in a chamber and then released by a valve. No slapping back and forth of a large internal spring.

Pros:

CO2 Airguns:

• CO2 Airguns allow for multiple shots per CO2 cartridge for more realistic action shooting.

• CO2 Airguns do not require any human effort to charge the gun other than loading the CO2 and Ammo into the Airgun.

• CO2 Airguns allow for true semi auto shooting ability. 

Spring Piston Airguns:

• Spring Airguns have the potential for high velocity since the larger and stiffer the spring, the greater the output force.

• Spring Airguns do not require anything other than your ammunition, typically either a Pellet or BB.

• Spring Airguns are mechanically very simple which makes them very reliable and less expensive to produce than other types of Airguns. 

Pump Airguns:

• Pump Airguns have the potential for high velocity since more pumps equals greater output force, only limited by the users strength and the pressure rating of the Airgun.

• Pump Airguns do not require anything other than your ammunition, typically either a Pellet or BB.

• Pump Airguns have next to no recoil which makes them very easy to shoot and highly accurate.

Cons:

CO2 Airguns:

• CO2 Airguns require the purchase and use of CO2 or they simple do not work.

• CO2 Airguns are very susceptible to temperature changes, especially cold temperature since CO2 needs a warm environment in order to expand. Cool down effect also plays a role in power output.

• CO2 Airguns have a maximum set amount of power output.

Spring Piston Airguns:

• Spring Airguns require the pre-cocking of the spring for each shot.

• Spring Airguns can take some getting used to since the spring recoil/vibration requires a very lose grip (Military Grip) to shoot accurately with them.

• Spring Airguns should not be stored pre-cocked since this can damage the spring, less so with gas spring versions. 

Pump Airguns:

• Pump Airguns require pre-pumping to pressurize the air chamber for each shot.

• Pump Airguns, especially Multi-Pump Airguns take the most amount of human effort for each shot.

• Pump Airguns need to stored with at least one pump in them or the seals can get damaged over time.

In this Comparison video I go through the benefits and shortcomings of both Blowback and Non-Blowback Airguns. I focus mainly on Airguns but there is a definite crossover with Airsoft guns.

Here are some basic statements that best describe both Blowback and Non-Blowback Airguns.

Blowback Airguns:

• Blowback Airguns usually have a movable slide that moves back and forth with each shot.

• Sometimes the blowback operation is internal (Internal bolt) so there may not be an external moveable slide.

• Some CO2 is used to move the slide rearwards in a Blowback Airgun.

• The Blowback motion of the slide with some blowback airguns can also cock the hammer or internal striker allowing for true single action trigger pull. But not always!

• Some Blowback airguns have the potential for full auto capabilities since they can have a true semi auto action.

• There is some noticeable recoil from the Blowback action simulating the recoil of a real gun.

Non-Blowback Airguns:

• Non-Blowback Airguns can have fixed or movable slides but they will not cycle back and forth with each shot.

• Non-Blowback Airguns tend to have less working parts since no Blowback valves are required or even a moveable slide.

• There are some Blowback and Non-Blowback Airguns that field strip similarly to their real steel counterparts but this is most commonly found in Blowback Airguns.

• Non-Blowback Airguns require the shooter to cock the hammer for single action shooting or use a double action trigger pull for semi auto like performance.

Pros:

Blowback Airguns:

• Blowback Action causes a noticeable recoil which makes the airgun feel more realistic.

• Blowback Airguns in some cases have true semi auto action with true single action triggers which mimic the authenticity of the real steel versions of the guns they replicate much better making them better training tools.

• Having some recoil makes blowback Airguns potentially better training tools.

• Blowback Airguns look really cool when shooting them  and are great action prop guns.

Non-Blowback Airguns:

• Non-Blowback Airguns tend to have less working parts so less to go wrong and more reliability.

• Non-Blowback Airguns can be more accurate since the recoil from the blowback is not a factor.

• Non-Blowback Airguns have more potential power and more shots per CO2 since no CO2 is robbed for the blowback operation.

Cons:

Blowback Airguns:

• Blowback operation can rob some of the power and will also rob how many shots you get from the Airgun.

• Blowback Airguns are effected even more by cold weather and the cool down effect.

• The recoil from Blowback Airguns can effect accuracy for some shooters.

Non-Blowback Airguns:

• Non-Blowback airguns are generally double action when shooting semi auto and so the trigger pull will be longer and heavier.

• Non-Blowback Airguns do not replicate the recoil action of a real gun.

• Non-Blowback Airguns do not look as cool to shoot and are not as good of an action prop gun.

It seems like most Replica Airguns collectors are looking for their Replica Airguns to be made out of metal. I even get people complaining about the frames of their airguns being made out plastic (polymer), when in fact the real steel version the gun is designed to replicate also has a plastic or polymer frame.

Most modern real guns are made as light weight and compact as possible, utilizing high grade plastics (polymer) and light weight metals. Of course they use high grade hardened steel in areas where the gun receives the most pressure and continuous wear and tear.

In the real steel gun world, lighter is often better since carrying around a 3 pound pistol all day can be uncomfortable. On the other hand in the Replica Gun world it can be the other way around as replica airgun collectors want that heavy clanky gun that feels solid and real in the hand.

This begs the question - Do Airguns really need to be made out of metal? For strength reason generally not since high pressure is not a factor even in blank guns as there is no bullet holding the pressure in the barrel and when talking about an Airgun or Airsoft Gun, there is even less pressure on the internal parts. For this reason most companies use low grade metals that have a higher content of zinc, often called pot metal. Even though it looks and feels like gun steel it is not nearly as strong and will scratch and break much easier and not be able to handle high pressure. So even though you may think metal is a better option for an Airgun, the reality is that plastic can sometimes be a better option, at least in terms of durability.

What are the benefits to Plastic components:

• Lighter weight.

• More flexible, can take a bit of a beating without breaking.

• Does not show scratches or dents as much as metal. 

What are the benefited to Metal components:

• Gives the gun a more realistic weight, feel & sound.

• In some situations will wear better than plastic. 

What are the cons to Plastic components:

• Can be less realistic in weight, feel and sound.

• Can wear quicker than metal parts in some situations.

What are the cons to Metal components:

• Shows scratches and wear more.

• Lower quality metals can break or crack fairly easily. 

What do I prefer?

• I prefer realism so I like to have metal parts where they would be in the real version of the same gun.

• I like my Replica Guns to have a similar weight and feel as their real steel counterparts.

• I like higher quality metals to be used in the mechanical parts like: (pins, triggers, hammers, barrels, screws, springs, catches…)

• I don't mind the use of plastic when it is high quality plastic and again when used in a similar manor to the real steel version of the gun.

Watch my Vimeo video on What is Better - Plastic or Metal Replica Airguns?

I finally answer the question... Which Airgun is the Best? There has to be a best airgun out there right? So let's cut to the chase and stop waisting everyones time and money buying the third Best Airgun or even the second best Airgun! Why would you even want anything other than the very best Airgun available to mankind!

I really hope you weren't one of the gullible ones that actually bought something other than the Best Airgun, well I guess you're going to have to watch my YouTube video to find out which Airgun is the Best Airgun of all time...

Type: Airsoft AR M16 Styled Rifle.

Manufacturer:G&G.

Model:CM16 Carbine GBB.

Materials: Metal and plastic/fiber construction.

Weight: 5 pounds.

Barrel: 10 inches, metal non-rifled.

Propulsion: GBB

Action: Semi & full auto blowback.

Ammunition Type: 6mm plastic Airsoft BB's.

Ammunition Capacity: 30+ round magazine.

FPS: 370+.

I could pretty much copy and paste my review of my G&G CM16 Raider GBB since both of these guns are pretty much the same Airsoft Rifle with different finishings. Instead I will place a link to my G&G CM16 RaiderVersion 2 GBB AR Airsoft Rifle Review and insert some nice photos of the  G&G CM16 Carbine version for you to admire :)

Buy the G&G CM16 Raider GBB Airsoft Rifle in Canada - Buy G&G Airsoft Rifles in the US

Moving on to the head to head comparison of the Tanfoglio Gold Custom versus the Sig Sauer X-Five Sight Rail (Open version). Again like my previous video of the KWC Model M1911 Tac A1 versus the Cybergun-KWC GSG 92-M92, these two Air Pistols feature full size drop out metal magazines that hold the CO2 and 4.5mm steel BB's, along with full blowback with working slide catches, safeties and magazine releases. Both are field Strippable and both have the addition of sight rails with red dot sights for quick target acquisition.

I did not find either sight rail pistol to be all that much more accurate than similar open sight pistols like the KWC Model M1911 Tac A1 and Cybergun-KWC GSG 92-M92, but I did find that target acquisition was much quicker and even when I accidentally double tapped the trigger, the second round was right on target.

In this field test comparison I shoot both guns through my Chronograph to see what kind of feet per second performance each one shoots, I also take them back 30 feet and shoot 10 rounds on a paper target using a semi rested position for true accuracy results.

Watch my Field Test Head to Head Shootout for the Tanfoglio Gold Custom versus the Sig Sauer X-Five Sight Rail:

Buy BB Pistols in Canada 
Buy BB Pistols in the US

Buy KWC Sig P226 X-Five in Canada
Buy KWC Sig P226 X-Five in the US

Here is the third video in a series of Head to Head Air Pistol Shootouts. In this video place the KWC Model M1911 Tac A1 head to head versus the Cybergun-KWC GSG 92-M92.

Both CO2 4.5mm Replica Air Pistols feature full size drop out metal magazines that hold the CO2 and 4.5mm steel BB's. These super realistic BB guns also have full blowback with working slide catches, safeties and magazine releases and they can both be field stripped juts like the real steel versions.

In this field test comparison I shoot both guns through my Chronograph to see what kind of feet per second performance each one shoots, I also take them back 30 feet and shoot 10 rounds on a paper target using a semi rested position for true accuracy results.

Watch my Field Test Head to Head Shootout for the KWC Model M1911 Tac A1 vs Cybergun-KWC GSG 92-M92:

Buy the Swiss Arms P92 in Canada

Buy the Swiss Arms P92 in the US

Buy the KWC Model M1911 A1 Tac Blowback 4.5mm BB Pistol in Canada

Buy the KWC Model M1911 A1 Tac Blowback 4.5mm BB Pistol in the US

I stopped by the ICS Booth, we don't sell too much of their products but have carried a few items from time to time. ICS caries some nice quality Airsoft guns including the M1 Grand with real wood stock, and some AK & AR variants.

One of our suppliers had the new FN Herstal Five-seveN Blowback Airsoft pistol, I believe made by Marushin. Like the real FN Herstal Five-seveN, the pistol is pretty much all polymer including the slide and frame. This pistol also uses CO2 in the full size drop out magazine which should make it fairly powerful.

Looks like there is another Dan Wesson contender available now in the form of a Swiss Arms S&W 357 Magnum 4 inch and 6 inch barreled version, they look really nice and like the Dan Wesson have the realistic reusable brass shells that hold the 4.5mm Steel BB's.

Ever considered owning a  mobile Gunsmith vehicle, look no further, I came across this pimped out Firearms Van complete with machine guns mounted in the front :) Inside was a complete firearms workshop.

Last but not least, we had some fun while in Vegas. I go down for the SHOT Show for business but I also bring my wife and we make time for some non business related activities. I generally stay at the WorldMark resort each time and this year the weather was pretty nice so we where able to get some sun by the pool a couple of days and I even got a tan line! Of course the food and entertainment is always awesome in Vegas.

We carry a lot of the G&G line and perhaps have as much in stock as you would find at the G& G booth ;) I did see a few items we do not have in stock so I will have to see what I can do about that. Some products that I hope to see added to our Canada Replica Airguns Store would for sure be the M1 Grand and our Canadian Military Colt C7A1/2.

One company I took notice of was Inokatsu, they make super high quality Airsoft guns. I was drawn to their Sig Sauer P229 and 1911 pistols that by the way are made out of real steel and as close to the real version as possible without it being a real gun. The Inokatsu pistols I looked at are not cheap and will set you back over a grand but are as close as you can get to a real sidearm as possible in an Airsoft version. They feel amazing to shoot with heavy blowback and that sound real steel makes when the slide snaps back.

Let me know if you're like me and would be willing to part with a substantial amount of money for one of these treasures? 

I get many question over on my Vimeo Channel, lots of times people asking me which gun is better and in most cases it really comes down to personal preference. But in some situations the comparisons are really close and to be honest it's even hard for me to decide which gun I think is better.

I get asked which one has higher fps, or is more accurate, or has harder blowback recoil... the list goes on. Without actually taking both gun outside and doing a head to head test using the same exact situations, I really can not honestly tell you! So that's exactly what I am going to do. Take some of the most commonly asked about gun comparisons and have a showdown.

Over the next while I will be making a total of five separate videos where I compare the following CO2 BB pistols head to head:

• The Tanfoglio Gold Custom versus the Sig Sauer P226 X-Five Sight Rail Version

• The KWC Model M1911 Tac A1 versus the Cybergun/KWC GSG 92/M92

• The ASG Dan Wesson 8 inch Revolver versus the Umarex Smith & Wesson 327 TRR8

• The ASG CZ 75 P-07 Duty versus the ASG Bersa BP9CC versus the ASG STI Duty One 1911

• The Gamo PT-85 versus the Umarex Beretta PX4 Storm

Make sure to come back and check out these upcoming head to head field test shooting videos!

So it's 2014 but I still needed to make my 2013 Airgun, Airsoft Gun and Blank Gun Collection Favorites for 2013. It's become a tradition I guess you could say. No I do not show all the guns in my collection but I do cover most of my favorites and also some new guns I picked up in 2013.

Here's a peek but make sure to watch the YouTube video bellow where I go over all my top picks for 2013. You can also buy many of the guns I show in this YouTube video over in our Canada and US Replica Airguns Store!

2013 BB Pistols

2013 Pellet Pistols

2013 Airsoft Pistols

2013 Blank Pistols

2013 Rifles

Type: GBB Airsoft Machine Pistol (Used).

Manufacturer: KSC

Model: Cobra M11A1

Materials: Plastic and metal.

Weight: 2.9 pounds (1315 grams).

Barrel: Metal non-rifled.

Propulsion: GBB.

Action: Single action only.

Ammunition Type: 6mm plastic Airsoft BB's.

Ammunition Capacity: 40 rounds.

FPS: 300+ fps.

Trigger Pull: The trigger pull on the KSC M11A1 GBB Airsoft Machine Pistol is pretty much exactly what you would expect from this fast firing single action only semi and full auto machine pistol, it has a really short take-up and then a nice crisp light trigger pull. Since it is an open bolt system, you will need to pull back the bolt for the first shot, releasing the trigger releases the bolt, just like with a real M11A1.

Accuracy: At this point because I received this gun from another collector in used condition, it is not working 100%, the hop-up bucking was damaged and the new ones I ordered are not the correct versions for this Airsoft gun. It does shoot but it is temperamental, sometimes the bolt will not cycle all the way and I have no idea how this is effecting the fps and accuracy. It would not be fair to test it in this condition, hopefully I can find the right hop-up bucking for it and do the Field Test Shooting Review at some point.

Build Quality: MyKSC M11A1 GBB Airsoft Machine Pistol has been used a fair bit so it is somewhat battle scarred, still it looks pretty good and other than the Hop-up bucking problem I am having it should be in working condition, unfortunately without the correct hop-up bucking, this gun will not work properly. Hopefully I can find a hop-up bucking? Even though much of this machine pistol is plastic externally, it has held up very well, the metal parts do also help to balance it off and give it a decent overall 3 pound weight which feels good considering it is such a small gun. 

Realism: The KSC M11A1 GBB Airsoft Machine Pistol is a very close copy of the real steel Cobra M11A1 Machine Pistol, all the parts appear to function just like the original Cobra RPB Industries M11A1 and it even field strips in the same manor. The full licensing and trademarks also help to make this replica very believable.

Reviewed by:ReplicaAirguns.com

Pros:

• Very realistic and accurate replica with full Cobra RPB Industries licensing.

• Even though there is lots of external polymer, it still has good weight to it.

• Full metal 40 round drop out magazine, holds BB's and Gas.

• Everything works like the original, field strips and lots of mechanical parts. 

• Shoots in both semi and full auto.

Cons:

• Hard to get here in Canada and hard to get parts here in Canada.

• Mostly plastic main build - Limited usage of metal and steel.

• Have no idea how it will perform because it is not functioning at 100%.

Comments:

Well I've pretty much said everything I can say without actually shooting it? Even though my used KSC M11A1 GBB Airsoft Machine Pistol is not in 100% working condition, I still like having it as I like the replica aspects of owning it, how else would I get my hands on a .380 caliber full auto machine pistol here in Canada ;) And you never know, I may just luck out and find the proper hop-up bucking for it and then have the chance to do my Field Test Shooting Review for you all :)

My Vimeo Table Top  Review of the KSC M11A1 GBB Airsoft Machine Pistol:

Buy BB Mini UZI in Canada

Buy BB Mini UZI in the US

Type: Airsoft AR M16 Styled Rifle.

Manufacturer:G&G.

Model:CM16 Raider GBB

Materials: Metal and plastic/fiber construction.

Weight: 5 pounds.

Barrel: 10 inches, metal non-rifled.

Propulsion: GBB

Action: Semi & full auto blowback.

Ammunition Type: 6mm plastic Airsoft BB's.

Ammunition Capacity: 30+ round magazine.

FPS: 370+.

Trigger Pull: The trigger pull on the G&G AR styled Airsoft CM16 Raider is very smooth, the CM16 Raider uses a mechanical trigger that once the charging handle has been pulled back or "charged", works in a single action only manor with a slight bit of take-up and then a light predictable release. Each time the closed bolt gas blowback system shoots a round in semi or full auto, the internal action is ready for the next single action shot.

Accuracy: So far I have not tested Version 2 of the G&G CM16 Raider, but I have tested Version 1 so here are the result I got with Version 1 until I do my official Field Shooting Test with Version 2. When shooting from a 30 foot distance I did get some nice closely grouped shots from the G&G CM16 Raider Gas Blowback but when shooting in full auto it did spread apart somewhat, maybe from the GBB recoil? Version1 of the G&G CM16 Raider GBB shot an average of just over the 325 fps, I was using .25 gram BB's and it was a cool day so you can expect higher fps out of the G&G CM16 Raider when conditions are better.

Build Quality: The G&G CM16 Raider GBB being built on G&G Combat Machine Platform is targeted more for the price conscience person. The quality is consistent and good and I did not mind having more plastic in the G&G CM16 Raider GBB as my plan from the beginning was to add a lot of extra accessories and starting out with a somewhat lighter footprint made the gun still relatively usable even when all geared up with extra accessories. I also feel the plastic or polymer fiber upper and lower receiver and RIS rail system will also wear better than steel as it is more likely to flex rather than break in many situations, not to mention metal will show scratches and wear more over time.

Realism: Airsoft AR rifles in my opinion are very realistic in general, even the AEG versions work just like the real steel AR's with working charging handles, dust covers, bolts, magazine, adjustable stocks and sights, but I would have to give the advantage to the gas Blowback systems like the G&G CM16 Raider GBB as it has a full internal bolt with some decent recoil, it can also be field striped very similarly to a real AR15 rifle. The shot count is more like what you would find in an M16 or AR rifle which means you will need to consider ammo shot assuage and reloading more carefully when using it in an Airsoft game.

Purchased From: The Replica Airguns Store.

Pros:

• Super affordable Gas Blowback Airsoft AR M16 styled Rifle.

• Very high rate of fire in full auto.

• Polymer shell is both light and very durable, does not show scratches or wear as easily as metal.

• All most every part is operational - Fully Ambidextrous now.

• Can be fully customized, lots of mounting points on the RIS Rail system.

• Fully adjustable Crane Stock.

• Removable rear Iron Sight can be swapped out for other sighting systems and hardware.

• Version 2 is a significant upgrade from Version 1.

• Internals can be swapped over to make it an AEG gun.

Cons:

• Some people may not like the polymer RIS rails and upper and lower receiver?

• Would have liked to have seen some sort of a plate over the pistol grip to finish it off.

Comments:

I already really liked Version 1 of the G&G CM16 Raider GBB Airsoft AR Rifle and even bought a bunch of magazines and gear to sport mine up for use in some local Airsoft games, the upgrades and improvements found in Version 2 are the icing on the cake! I am hoping the internal performance enhancements will increase the FPS just a bit and Gas efficiency somewhat over Version 2 but will find out when I give it a thorough testing shortly. If you have been a bit scared off by the higher prices of some GBB Gas Blowback Airsoft rifles then perhaps take a look at the G&G Combat Machine Platform CM16 Raider in GBB, it may just change your mind about Gas Blowback Airsoft rifles!

My Vimeo Video Review for the G&G CM16 Raider Airsoft GBB AR Styled Airsoft Rifles:

Buy the G&G CM16 Raider GBB Airsoft Rifle in Canada 

Buy G&G Airsoft Rifles in the US

Type: Airsoft Revolvers.

Manufacturer: ASG - G&G

Model:Dan Wesson 2.5 inch Gold - G&G G731 2.5 inch Silver & Black

Materials: Mostly metal.

Weight: 1.87 pounds. (850 grams) - 1.65 pounds. (750 grams)

Barrel: Metal non-rifled.

Propulsion: CO2 x 1.

Action: Revolver, single and double action.

Ammunition Type: 6mm plastic Airsoft BB's.

Ammunition Capacity: 6 rounds.

FPS: 394.

Trigger Pull: Both of these pistols have about the same style of triggers, they both shoot in true revolvers style offering single and double action triggers. The double action has a bit of friction to it since the cylinder is being rotate during the first part of the trigger pull and there is a spring fed metal gasket between the barrel and the cylinder that creates a seal but does apply pressure and results in some friction and a heavier trigger pull in double action. Single action is much lighter on both guns.

Accuracy: This part of my testing has not been conducted to date, I will put a link in here when I have completed my Shooting Field Test review for the ASG Dan Wesson 2.5 inch Gold and G&G G731 2.5 inch Airsoft pistols. Even thought the claimed fps is around 400 for both guns I am expecting more like 350-375 fps. Accuracy should be decent at closer ranges but since there is no hop-up, neither gun would be good at longer ranges in my opinion.

Build Quality: These detailed revolver are really well built! Both are almost all metal with just a few components made out of plastic, like the handles on both guns and the CO2 screw tab on the Dan Wesson. Both revolvers grips gave me just a bit of concern, you will need to be careful when snapping in the grip on the G&G G731 and the Dan Wesson grips have been known to ware a bit with heavy use. The finish on both of these guns is amazing and while the Silver finish on the G&G looks just like polished stainless steel, the Gold finish on the Dan Wesson offers a very unique and customized finish not found on too many guns. And if you just want classic black then there is always the G&G G731 in standard black as an option.

Realism: The ASG Dan Wesson and G&G G731 revolvers are as close as you can get to real six shooters, all the parts work pretty much like a real revolver, the realistic loading of the metal shells not only make it feel like you are handling a real revolver but also finish off the look making it really hard to tell that both these pistols are in fact Airsoft Revolvers.

Purchased From: The Replica Airguns Store.

Pros:

• Revolver with actual brass shells giving you the feeling of a real 6 shooter!

• Almost all metal design.

• lots of detail in both revolvers, very well made, fit and finish is excellent.

• Should have respectable power for a short barreled pistol.

• Fully adjustable sight on the ASG Dan Wesson.

• G&G G731 is super compact and flush, great out of the way back up side arm.

• No Red Tip on the Canada version.

Cons:

• Plastic CO2 screw tab on the Dan Wesson (but is well hidden and protected).

• A bit of concern with wearing and usage on the grips for both guns.

• No adjustable sight on the G&G G731 but super clean looking.

• Red tip on the US version :(

Comments:

As with all of these shell loading revolvers, they are just so realistic and really fun to load up and shoot. You actually get a bit of time in-between shooting to take a breath and enjoy the entire experience rather than just unload round after round with some of the other super high round magazine guns. I love the compact size of both guns, perhaps the G&G G731 just a bit more with it's super clean edges and even smaller profile. But on the other hand the Dan Wesson ASG 2.5 inch has that more aggressive combat look if that is more to your liking! Either way, both guns make a great choice for an out of the way revolver styled side arm when you need that extra backup firepower!

My Vimeo Video Table Top Review for these compact realistic Airsoft Revolvers:

Buy ASG Gold Airsoft Pistol in Canada  -  Buy Airsoft Revolvers in the US

Buy G&G G731 Airsoft Pistols in Canada  -  Buy Airsoft Revolvers in the US

Every so often I come across some interesting guns that people are willing to trade or sell me, if the price is right or the trade involves a gun I can part with, then I go for it and hopefully end up with something I may not be able to get new or that for me is hard to acquire in Canada.

My most recent trade added two new guns to the collection, a KSC M11A1 Airsoft Machine Pistol and a Daisy Power Line 2003 .177 Caliber Pellet Pistol.

Both of these guns are very hard to get since the KWC Airsoft M11A1 shoots a  bit too week for import into Canada, and the Daisy 2003 is no longer in production.

The KSC M11A1 is a 6mm Airsoft pistol that shoots in both semi and full auto using a Gas Blowback open bolt system, it is a replica of the .380 Caliber Cobra RPB Industries M11-A1. Mine came with a mock suppressor and 7 magazines, although not all of them are in working condition. The KSC M11A1 is in working condition but needs a new Hop-up Rubber Bucking which I have on order.

The Daisy Power Line 2003 seems to be in really good condition but still needs to be tested, it is one of the only true blowback semi auto pellet pistols I know of, what I mean by this, is it has a true blowback system with a true single action trigger which means it can be converted to full auto which is one of the reason Daisy may have discontinued it. The Daisy Power Line 2003 uses a very interesting 35 round rotational magazine. Some say it is loosely styled after a Browning High Power pistol.

Stay posted for reviews on both of these pistols down the road.

Buy BB Mini UZI in Canada   -   Buy BB Mini UZI in the US

Buy Airsoft Mini UZI in Canada   -   Buy Airsoft Pistols in the US

You may wonder why I am doing another video on the G&G CM16 Raider Gas Blowback Airsoft AR Rifle? That's because the one I have here in this Update Video is Version 2 and yes there is a difference. So far I can only tell you about the obvious stuff since I really have not tested it out to see if there are any other performance gains with Version 2 over Version 1.

G&G has made some improvement with Version 2 enhancing several areas:

• First off, there is now a selector switch on both sides of the receiver allowing for left or right handed use.

• Carrying on with the ambidextrous theme, G&G also added a magazine release to the left side of the receiver.

• Another missing feature was a bolt lock out when your magazine was empty, this has been added and so the bolt will lock back about 1/3 the way back locking out the gun and letting you know when you are out of ammo.

• The bolt release on Version 1 was just for show and did not function. On Version 2, with the bolt lock, G&G also added a working bolt release.

Those are some pretty significant improvements to the G&G Armament CM16 Raider GBB Version 2 in my books! So now it's time to test it out and see if full auto mode has been improved. I found with Version 1, that when using full auto, the G&G CM16 Raider GBB would have some trouble getting through a full mag dump but when shooting very quickly in semi auto had no problems at all.

Make sure to check back for my full review and shooting field test for the G&G CM16 Raider GBB Version 2 AR Airsoft Rifle.

Buy the G&G CM16 Raider GBB Airsoft Rifle in Canada - Buy G&G Airsoft Rifles in the US

Type: Airsoft.

Manufacturer:King Arms.

Model:Thompson M1A1 Military & M1928 Chicago (Gold & Chrome).

Materials: Metal & Wood.

Weight: 6.6 pounds.

Barrel: 15 inches, metal.

Propulsion: AEG

Action: Semi/full auto, single action.

Ammunition Type: 6mm Plastic BB (recommended .20 gram plus).

Ammunition Capacity: 420 round magazine.

FPS: 380-410.

Trigger Pull: The trigger pull on the King Arms Thompson Machine Guns is fairly short and light as it is essentially just an on-off switch for the internal electronic components. You can shoot this gun very quickly in semi auto mode, and of course even quicker when full auto is selected. As with all AEG systems their is a slight delay between when you pull the trigger and the shot is taken as the internal spring needs to compress first before releasing.

Accuracy: In many cases Airsoft guns can be just as accurate as 4.5mm BB guns, well at least at fairly close ranges, I was able to get most of my .25 gram BB 10 round target test shots within 1 inch from 30 feet away using a semi-rested position. There where a couple BB's that lengthened the group out to about 2 inches but still a very good result when you consider these are plastic BB's being used. In Terms of FPS, I did stick with the slightly heavier 2.5 gram Airsoft BB's and still got a decent 360 average 5 shot Chronograph test result making this AEG Airsoft rifle perfect for just about any Airsoft game type.

• Click here to watch my Field Test Shooting Video for these King Arms Thompson Machine Guns

Build Quality: The King Arms 23 Karat Gold and Chrome Platted AEG Thompson Machine Guns are very well made using Aluminum Zinc Alloy bodies and real Wood Stocks, the fit and finish is very good and pretty much everything on these rifles are either metal or wood. You will have to polish these guns with a cloth from time to time since the mirror finish shows every smudge and finger print.

Realism: I'm not sure how many real 23 Karat Gold and Chrome Platted Thompson Machine Guns there are out there but there has to be at least a few ;) But going on how these guns look and feel, they are solid and very realistic. Some people have mentioned that the bolt should be on the top for some versions of the Thompson's but there are some Thompson's with the bolt on the side so I suppose we will let that one slide. The Wood stocks are a real plus adding to the overall weight and authenticity. Most parts works as they would on the real steel Thompson M1A1 Military or M1928 Chicago (Gold or Chrome) AEG Airsoft Machine Guns.

Available in the: The Canada Replica Airguns Store.

Pros:

• Gorgeous Wood stock and Gold or Chrome platting.

• Nice high capacity metal magazines, can be mixed and matched.

• Adjustable rear sight for windage with two sight positions (Notch & Peep).

• Semi and full auto selectable with really nice rate of fire.

• FPS is bang on for indoor or outdoor Airsoft games.

• Fully Thompson licensed.

• Comes with Certificate of Authenticity.

Cons:

• Does not come with a battery or charger.

• Prone to finger prints and smudges.

• Need to use a screw driver to get at the battery.

Comments:

I am a big fan of the King Arms Thompson line, even the all black version with the plastic stocks looks and functions great. Internally the lower cost black version is the same and having previously shot my black Thompson, I knew these blinged out 23 Karat Gold and Chrome Platted versions where also going to perform as good as they looked! I'm not so sure about buying a Gold or Chrome Thompson for everyday use, since they will get knocked around and scratched up but if you are looking for the best of the best with real wood stocks and all metal parts then make sure to consider one of the Thompson 

My Vimeo Video Review for the King Arms Thompson Gold & Silver AEG Airsoft Machine Guns:

Buy the King Arms Thompson Special Gold & Chrome AEG Rifles in Canada