This comparison Review Video serves a few purposes, first to compare the ASG Dan Wesson 715 Revolver 4.5mm steel BB version to the 6mm plastic Airsoft version in both velocity and accuracy. Secondly to give my new Chrony Chronograph with lighting kit a test to see if I can get more reliable readings in lower light and thirdly to try and redeem the Steel BB version of the Dan Wesson 715 as last time I tested it, it did not get all that high of fps readings, well below the claimed 430 on the box.
In this review video I test both Dan Wesson 715 Revolvers out, first with my Chrony Chronograph and then all in one take I setup and shoot 6 rounds each on separate paper targets from 30 feet back to see how accurate the smaller heavier Steel BB rounds are compared to the larger lighter Plastic BB's. I used 5.1 grain RWS 4.5mm Steel BB's and .20 gram 6mm plastic BB's and installed brand new 12 gram CO2 cartridges in both guns.
In terms of my Chrony consistency, the smaller steel BB's still struggled to get consistent readings with only 2 out of 6 shots while the larger Airsoft BB's managed to get a good reading 4 out of 6 shots. Steel BB velocity was right around 350 fps while the Airsoft BB's where travelling much faster at closer to 450 fps.
Both the Steel BB and Airsoft CO2 Dan Wesson 715 Revolvers shot 6 round grouping of about 2 inches with 4 out of the 6 shots making a much tighter 1 inch group again with both ammo types. The Airsoft Dan Wesson 715 seemed to be centered on target well while the Steel BB Dan Wesson 715 shot a bit low.
As most my Vimeo Subscribers and Viewers will already know, I have been struggling with my Chrony Shooting Chronograph for a while now. I know some of it is to do with the bad lighting under my deck but over time my Chrony F-1 Shooting Chronograph has become less and less reliable to the point now that I simply don't get any usable feedback from it. If I'm lucky on a good day I might get one FPS reading out of ten shots which is nothing I can use.
So recently I went out and purchased a new Chrony Shooting Chronograph, I actually upgraded a little bit and got the higher end Chrony Beta Shooting Chronograph version which has more options than my older F-1 Chrony like:
Selector switch to change from FPS (feet per second) to MPS (meter per second).
Delivers Measurements and Statistics such as - High, Low and Average Velocities, Extreme Spread and Standard Deviation.
Retrieve individual Shot Velocities and Statistics.
Has temporary working memory.
Has 60 shot permanent memory (divided into 6 numbered strings of up to 10 shots each, with one set of Statistics for each string).
Delete individual shots (with automatic adjustment of Statistics).
Delete the content of a whole string or all data from memory.
Can be switched off, taken home & switched on again for reviewing and information retrieval.
Memory will stay even without battery.
Moves instantly from string to string, interrupts shooting on any string without memory loss, returns to any string to continue where you left off.
Change string size.
Stereo Jack for optional Printer or Remote Control.
Forget Button - To clear individual strings instantly.
In this review video I mainly show you around my new Chrony Beta Shooting Chronograph and don't really talk too much about features since it is all new to me and I have not played around with my new Beta Chrony much so far.
Make sure to watch my Vimeo video for this Comparison Review as I go into a lot of detail about the similarities and difference with each of these CO2 Blowback Pellet Guns.
All of these CO2 blowback pellet guns are made for each company in Japan (I am assuming from the same factory?)
All of the listed Pellet Airguns shoot .177 caliber pellets (Can be Alloy or Lead)
They all have double sided rotary stick magazines that hold 8 rounds on each end for a total of 16 shots per magazine.
All of the Airguns use 12 gram CO2.
All compared pellet guns have Blowback operation.
All of these pellet pistols have single and double action triggers except for the Gamo MP9 which is single action only and needs to be charged on the first shot.
They all have rifled barrels.
Here is where we find some key differences between these CO2 Blowback Pellet Pistols:
Trigger Pull: The trigger pull on the Sig Sauer ASP P250 CO2 Blowback .177 Caliber Pellet Pistol is a lot better than I thought it was going to be. The blowback operation does place the hammer in the cocked position for single action type shooting but the the trigger is still required to index or advance the next pellet to line up with the barrel. Because of this, trigger pull is full length even in single action mode but you can barely feel any added friction from the indexing of the rotary magazine. All of this makes for a slightly longer trigger pull but one that is light weight with a fairly nice and easy release. For some reason the Sig Sauer P226 trigger does feel a little smoother with a slightly easier release.
Accuracy: I have not done my official Field Test Shooting Video with the Sig Sauer ASP P250 CO2 Blowback .177 Caliber Pellet Pistol and I am not sure when I am going to get the chance to do so since I am waiting on a replacement Chronograph for my velocity portion of my testing. That said I can say that Sig has already done some of the work for me and conducted their own "real world" velocity testing for their ASP line of CO2 Pellet Guns. Sig tested both a standard 8.18 grain lead pellet and a high velocity 5.25 grain alloy pellet shooting an 8 shot string with each to find out average fps performance for both pellet types. The 8.18 grain lead pellet average 353 fps while the 5.25 grain alloy pellet average 399 fps. In terms of accuracy, I was able to get just under a 2 inch 16 shot well centered grouping on two separate 30 foot back tests which is pretty decent. I did notice that when shooting a 16 shot string, the first and last shot velocity will vary a fair amount as the CO2 cools the gun and lowers the fps. I would recommend taking your time in-between reloads to let the Sig Sauer ASP P250 CO2 Blowback .177 Caliber Pellet Pistol warm back up.
Build Quality: The Sig Sauer ASP P250 CO2 Blowback .177 Caliber Pellet Pistol is a bit on the lighter side coming in around 1.5 pounds since it does incorporate both metal and plastic construction. You will find the Sig Sauer P250 has a metal slide and plastic frames similar to the real steel version. Weighing it at 1.45 pounds, the P250 is lighter then a standard Sig Sauer P250. Sig claims that their entire APS line of pellet guns is life tested for 15,000 shots so you know this gun is going to last and provide years of shooting fun. The fit and finish seem really good, so far no real paint or finish problems and all mechanically everything is operating as it should.
Realism: The Sig Sauer ASP P250 CO2 Blowback .177 Caliber Pellet Pistol is a very close replica of the real steel Sig Sauer P250. I really like the fact that the safety also works as a working decoker just as it would on the real Sig P250. Other similar working parts are the magazine release and the hammer that stays back for true single action shooting. The slide catch release and take down leaver are purely for show but they are not moulded in parts so they look good and realistic. One slight disappointment for me is when a gun does not have a cut out ejection port, that is the case with both the Sig Sauer ASP P226 and P250 but it does not take away from the shooting fun in any way.
Good overall replica of the real steel Sig Sauer P250.
Designed by Sig and made in Japan, fully Sig Sauer licensed.
Nice heavy blowback operation.
It might feel a bit light weight at first but out of the two Sig Sauer ASP pellet pistols this one seems to shoot a bit better.
Got respectable accuracy and seemed to shoot pretty hard.
Safety works as the de-cocker same as the real Sig Sauer P250.
White dot sights and accessory rail.
Great feel to the trigger not heavy or sticky in any way.
Cons:
Shots tended to slow down a bit near the end of a 16 shot strong as the gun cooled down.
Sight are non adjustable.
Ejection port is not cut out.
Comments:
What I really like about the Sig Sauer ASP P250 CO2 Blowback .177 Caliber Pellet Pistol is that like all the other APS Airgun from Sig, it is a product that Sig has decided to invest a lot of their time and effort to develop rather then simply grab an existing Airgun product from a manufacturer and slap their license on it. Sigs product ingenuity is what will help to improve the airgun industry overall. Getting back to the Sig Sauer ASP P250 CO2 Blowback .177 Caliber Pellet Pistol, it may feel a bit light weight at first but the heavy blowback will rock you unexpectedly! I found in terms of comparison to the Sig Sauer ASP P226, the P250 was more accurate and well centered on target for me as well. If you're a Sig Sauer P250 owner you are for sure going to want to pick yourself up one of these ASP CO2 Blowback Airgun versions so you can get some extra practice time in for pennies per shot and the ability to shoot in a lot more locations..
My Vimeo Table Top Review of the Sig Sauer ASP P250 CO2 Blowback .177 Caliber Pellet Pistol:
Trigger Pull: The trigger pull on the Sig Sauer ASP P226 CO2 Blowback .177 Caliber Pellet Pistol is a lot better than I thought it was going to be. The blowback operation does place the hammer in the cocked position for single action type shooting but the the trigger is still required to index or advance the next pellet to line up with the barrel. Because of this, trigger pull is full length even in single action mode but you can barely feel any added friction from the indexing of the rotary magazine. All of this makes for a slightly longer trigger pull but one that is light weight with a fairly nice and easy release.
Accuracy: I have not done my official Field Test Shooting Video with the Sig Sauer ASP P226 CO2 Blowback .177 Caliber Pellet Pistol and I am not sure when I am going to get the chance to do so since I am waiting on a replacement Chronograph for my velocity portion of my testing. That said I can say that Sig has already done some of the work for me and conducted their own "real world" velocity testing for their ASP line of CO2 Pellet Guns. Sig tested both a standard 8.18 grain lead pellet and a high velocity 5.25 grain alloy pellet shooting an 8 shot string with each to find out average fps performance for both pellet types. The 8.18 grain lead pellet average 359 fps while the 5.25 grain alloy pellet average 403 fps. In terms of accuracy, I was able to get about a 2 inch 16 shot grouping on two separate 30 foot back tests which is pretty decent. I did notice that when shooting a 16 shot string, the first and last shot velocity will vary a fair amount as the CO2 cools the gun and lowers the fps. I would recommend taking your time in-between reloads to let the Sig Sauer ASP P226 CO2 Blowback .177 Caliber Pellet Pistol warm back up.
Build Quality: The Sig Sauer ASP P226 CO2 Blowback .177 Caliber Pellet Pistol is a very solid feeling pistol with its all metal construction. Weighing it at 2.35 pounds, it is actually a tad bit heavier then the real steel version but not by much. Sig claims that their entire APS line of pellet guns is life tested for 15,000 shots so you know this gun is going to last and provide years of shooting fun. The fit and finish seem really good, so far no real paint or finish problems and all mechanically everything is operating as it should.
Realism: The Sig Sauer ASP P226 CO2 Blowback .177 Caliber Pellet Pistol is a very close replica of the real steel Sig Sauer P226, I would say it most closely takes after the MK-25 Threaded Barrel version. I really like the fact that the safety also works as a working decoker just as it would on the real P226. Other similar working parts are the magazine release and the hammer that stays back for true single action shooting. The slide catch release and take down leaver are purely for show but they are not moulded in parts so they look the part. One slight disappointment for me is when a gun does not have a cut out ejection port, that is the case with both the Sig Sauer ASP P226 and P250 but it does not take away from the shooting fun in any way.
Good overall replica of the real steel Sig Sauer P250.
Really solid feeling gun, has awesome weight to it with it’s all mental construction, pretty close in weight the real steel version.
Designed by Sig and made in Japan, fully Sig Sauer licensed.
Nice heavy blowback operation.
Got respectable accuracy and seemed to shoot pretty hard.
Safety works as the de-cocker same as the real Sig Sauer P226.
White dot sights and accessory rail.
Super easy CO2 loading system, no having to tighten a CO2 tab.
Great feel to the trigger not heavy or sticky in any way.
Cons:
Shots tended to slow down a bit near the end of a 16 shot strong as the gun cooled down.
Sight are non adjustable.
Ejection port is not cut out.
Comments:
What I really like about the Sig Sauer ASP P226 CO2 Blowback .177 Caliber Pellet Pistol is that like all the other APS airguns from Sig, it is a product that Sig has decided to invest a lot of their time and effort to develop rather then simply grab an existing arigun product from a manufacturer and slap their license on it. Sigs product ingenuity is what will help to improve the airgun industry overall. Getting back to the Sig Sauer ASP P226 CO2 Blowback .177 Caliber Pellet Pistol, it's a really solid CO2 Pellet pistol that is a lot of fun to shoot and for Sig Sauer P226 owners, the pellet shooting airgun version offers a super economical and safe way to get some practice in using a product that looks, feels and shoots similarly to their real steel counterpart.
My Vimeo Table Top Review of the Sig Sauer ASP P226 CO2 Blowback .177 Caliber Pellet Pistol:
Materials: Plastic main body with some metal parts.
Weight: 1.6 pounds (708 grams).
Barrel: 5.5 inches - Metal none rifled.
Propulsion: 12 gram CO2.
Action: Blowback single action only.
Ammunition Type: 4.5mm Steel BB's.
Ammunition Capacity: 20 round top loading stick magazine.
FPS: 350+.
Trigger Pull: The trigger pull on the Daisy Powerline Model 400 CO2 Blowback BB Pistol is single action only and has about a medium pull to it, not the lightest single action trigger I have shot by far but not too heavy by any means. There is some initial take-up with a noticeable release point.
Accuracy: Make sure to watch my full Field Test Shooting video for th PHOTO4 Daisy Powerline Model 400 CO2 Blowback BB Pistol. When performing my usual 30 foot out paper target shooting performance test I was able to get about a 2 inch 10 shot grouping using a semi rested stance. This pistol did shoot rather on the high side so you will have to aim low as the sights are non-adjustable. In terms of velocity I was able to get fairly consistent 350fps performance using a brand new CO2, this is pretty good considering this is a 20 year old pistol and may have been one of the first blowback airguns to hit the market. The Daisy Powerline Model 400 CO2 Blowback BB Pistol was a bit of a CO2 hog only getting around 50 shots out of one 12 gram CO2.
Build Quality: The Daisy Powerline Model 400 CO2 Blowback BB Pistol is a mainly all metal airgun but it is solid and well built, The plastics used long ago in my opinion are superior in terms of longevity to today plastics. Being a Japan built gun is also a plus and you will find metal parts where they need to be as in the hammer, trigger, barrel, safety and many other internal parts. Keep my used pistol is over 20 years old and still looks and works like new.
Realism: The Daisy Powerline Model 400 CO2 Blowback BB Pistol is an obvious replica of a Desert Eagle Semi Auto Pistol, there are no licensed markings but there is no doubt what this gun is intended to look like. In terms of size and overall appearance it is a good copy of a real steel Desert Eagle but it does weigh in a lot lighter being made mostly from plastics. Some mechanical parts are moulded into the gun like the safety and slide catch but the blowback operation helps add back to the realism. Of course the top loading 20 round BB magazine is not at all what you would expect to find on the real Desert Eagle, that said it is practical for loading a BB gun.
Trigger Pull: The trigger on the SM Mod 110 8mm Blank Pistol is single action only so you will need to rack the slide to not only chamber a round but also cock the internal hammer / striker, follow up shots will case the slide to cycle on it own allowing for single action shooting. The trigger is rather nice with just a slight bit of take-up followed by a light release.
Accuracy: NA.
Build Quality: The SM Mod 110 8mm Blank Pistol was made in West Germany sometime back in the Mid 70's so this pistol is 30-40 years old and still looks great. Mine does have some slight pitting on the right side I am assuming from sitting in the box up against the manual which more than likely may have an acidic property to it. Even so this pitting is minor and the gun is in good condition overall. Like most blank pistols much of the gun is made out of pot metal (a zinc alloy) but it does have hardened steel parts where they need to be (Barrel, ejector, hammer, pins, screws and magazine).
Realism: The SM Mod 110 8mm Blank Pistol is not a true replica as far as I can tell is not an actual replica of any real steel semi-auto pistol in production but it does look a bit like the American Derringer LM5. In terms of looking like a gun it looks like what you would expect a small caliber sub compact pistol should look like and all operation is exactly like a semi auto pistol with the exception that the SM Mod 110 only shoots blanks since the barrel is obstructed with a metal rod.
I really like unique blank guns since they are so hard to locate here in Canada. When I saw this sitting on the table at my local gun show I kind of wondered if someone had accidentally left out a prohibited firearm but once I inspected it I quickly realized it was a blank shooter and decided right there and then I had to have it. I did pay close to $200 for it but to me it is worth it simply because this little blank shooter is a rare find and it was also in really good condition and even came with the original 8mm self defence pepper blanks. The SM Mod 110 8mm Blank Pistol is for sure a blank shooter I will be holding onto for some time...
My Vimeo Table Top Review for the SM Mod 110 8mm Blank Pistol:
I was personally confused about some of the similarities and differences between several models of KJWorks Beretta M9 CO2 Blowback Airsoft Pistols, so I decided to make a video where I go over 4 models of KJWorks M9 Pistols and point out the commonalities and differences between them.
Here are the 4 versions of KJWorks Beretta M9 CO2 Blowback Airsoft Pistols:
All of them come with interchangeable 25 round CO2 Magazines.
All of them shoot around 360+ fps.
All have a metal slide and frame.
All weigh close to the same weight (2.1 - 2.4 pounds).
All shoot in single and double action.
All have ambidextrous safeties.
All have white dot sights.
Prices range from $184 -$200.
Here is a list of the differences between them:
The VE, Vertex and M9A1 come in a semi gloss finish while the Tactical is more of a matt black.
The VE and M9A1 have rails for accessory attachments while the Vertex and Tactical do not.
The Vertec, Tactical and M9A1 have laniard loops while the VE does not.
Some slight trigger guard differences between the models but very subtle.
The Vertex and M9A1 share the same style classic Beretta pistol grip, The Tactical has a tactical finger pistol grip and the VE has it’s own unique pistol grip.
Make sure to watch my Vimeo video where I cover this information in detail:
Trigger Pull: The single action only trigger pull on the Umarex Smith & Wesson M&P40 CO2 Blowback BB Pistol is very nice, there is some take up required be for the release but the release or break point is very smooth, perhaps a little too smooth since there is no real noticeable resistance so you will have to get use to the range in the trigger pull in which the release takes place. Since there is no external hammer you will need to draw the slide back in order to cock the internal striker.
Accuracy: Make sure to checkout my full Field Test Shooting Video for the Umarex Smith & Wesson M&P40 CO2 Blowback BB Pistol where I test out this fun S&W M&P40 BB shooting replica by shooting some BB's through my chronograph and also at a paper target to find out how it performs. In summary I was able to get an average of around 300 fps and accuracy in the 2 inch size groupings from 30 feet away. Not bad for a full blowback short barrel CO2 BB pistol. It did shoot a little low so some manual target sighting adjustments may be required.
Build Quality: Very good, with metal and plastic construction where you would find it on the real steel S&W M&P40. I am fairly certain the the Umarex Smith & Wesson M&P40 CO2 Blowback BB Pistol is made by KWC which has produce some other nice quality examples of other full blowback replica BB and Airsoft pistols. As with most KWC powder coated airguns, you will get some wear in the high spots of the finish over time but this is true even with real steel blued guns.
Realism: This is by far the best example of a 4.5mm BB shooting Smith & Wesson M&P out there, I have had several real steel M&P40 owners comment on how accurate this BB copy really is including how the barrel drops from its locked position and angles down and up during blowback operation. You even get interchangeable grip backstraps to accommodate different sized hands. And of course all the mechanical parts function as you would expect them to including being able to fully field strip the Umarex Smith & Wesson M&P40 CO2 Blowback BB Pistol.
Most accurate looking steel BB shooting replica of the S&W M&P40 to date.
Good weight and feel to it.
Metal and plastic parts where you would find them on the real steel version.
Realistic working safety and working slide catch and release.
Full size dropout metal magazine that holds BB's and CO2.
Can be field stripped like original Smith & Wesson M&P40.
Fully Smith & Wesson licensed via Umarex.
Rail for add on accessories.
White dot sight with adjustable front sight for windage.
Comes with three sizes of interchangeable grip backstraps.
Cons:
FPS may be low for some people that like the more powerful CO2 pistols.
Shoots a bit low out of the box.
Ugly white warning instruction on the slide.
Comments:
Many of us have been waiting for a blowback Smith & Wesson M&P and now we have one. Thanks to Umarex, we also get it in a fully licensed version to make it even more realistic! Everything about the Umarex Smith & Wesson M&P40 CO2 Blowback BB Pistol is so very accurate to the real steel version other than of course the fact that it shoots 4.5mm Steel BB's using CO2 but isn't that why we are interested in it in the first place? If you are a Real Steel S&W M&P owner than you are going to have to get yourself one of these as a low cost and easily accessible training alternative. A great choice fro anyone else looking for an ultra realistic 4.5mm CO2 blowback pistol what ever your purpose is.
My Vimeo Videos for the Umarex Smith & Wesson M&P40 CO2 Blowback BB Pistol:
This Vimeo Video Preview covers three really nice CO2 Pistols recently added to our Replica Airguns Canada Store. One is a pellet pistol from Gletcher called the Gletcher NGT R which is for the most part the same as the standard 4.5mm Steel shooting NGT but the R model is made to shoot .177 caliber pellets so it also has a rifled barrel. I am expecting pretty decent accuracy with this pistol!
Last but perhaps the best or at least most anticipated gun I am showing off today is the Umarex S&W M&P40 Full Blowback CO2 BB Pistol. This is a really nice acurate replica of the real steal S&W M&P40 with full licensing and pretty much every part operational like it would be on the .40 caliber version.
Here are some basic Specifications for all of these fine Co2 Airguns...
Action: Semi and full auto blowback, single and double action.
Ammunition Type: 4.5mm Steel BB's.
Ammunition Capacity: 18 rounds.
FPS: 310.
Trigger Pull: The trigger pull on the Umarex Beretta Mod. 92 A1 BB Pistol is like what you would expect from a real Beretta 92 A1, it offers both single and double action but most of the time you will be shooting in single action since the blowback cocks the hammer after each shot. Single action has a little bit of take-up but has a predictable release that is not overly light or heavy. Double action shots are longer and heavier which is as expected.
Accuracy: I have not shot this "version" of the Umarex Beretta Mod. 92 A1 but it will undoubtedly perform very similar to the many other full blowback CO2 pistols I have tested like the KWC and Cybgergun M92's, 1911's and Sigs. I did notice the slide spring on the Umarex Beretta Mod. 92 A1 CO2 Blowback 4.5mm BB Pistol to be very firm so I am expecting it to have pretty good blowback action. One other consideration is this CO2 airguns offers both semi and full auto shooting options but with the heavy blowback, don't expect much accuracy when shooting in full auto mode :)
Build Quality: Very good, with almost all metal construction, good weight and craftsmanship. Don't quote me on this but I have a feeling the Umarex Beretta Mod. 92 A1 CO2 Blowback 4.5mm BB Pistol may be made by KWC, if this is the case then we know to expect the same quality as we have found with other KWC full blowback airguns which is pretty good overall. There may be some wear in the high spots of the finish over time but I kind of like this since it gives the gun a more realistic look.
Realism: This is by far the closest Beretta Model 92 out there, even the magazine butt plate looks the part, the safety is true to form and it is full licensed and trademarked throughout the gun via Umarex. I'm not sure if the real steal Umarex ever offered full auto or not but we can look past this for the sake of how much fun it is going to be shooting in full auto! The only negative aspect in terms of realism is the white warning writing on the left side of the slide.
Your choice of shooting in either semi auto or full auto mode.
Really nice replica of the original Beretta 92 A1.
Great weight and feel to it.
All metal design, fit and finish is very good.
Strong slide spring so it should have heavy blowback action.
Realistic working safety and working slide catch and release.
Full size dropout metal magazine that holds BB's and CO2.
Can be field stripped like original Beretta 92 A1.
Fully Beretta licensed.
Cons:
Will probably eat CO2 especially in full auto mode.
Non-adjustable sights.
Ugly white warning instruction on the slide.
Comments:
I know the KWC M92 and Cybergun GSG 92 have been out for a while and the Umarex Beretta Mod. 92 A1 CO2 Blowback 4.5mm BB Pistol is along the same lines, but I do like that it is a true Beretta Replica rather than the Taurus copy. I like that Umarex went the extra mile and made the magazine look the part with a much shorter butt plate and adding semi and full auto right out of the box with a dedicated selector switch is pretty cool too. I am really looking forward to testing this gun out and seeing how the blowback action combined with the full auto ability is going to recoil, I have a feeling it's going to kick like a mule!
My Vimeo Videos for the Umarex Beretta Mod. 92 A1 CO2 Blowback 4.5mm BB Pistol:
Type: Pellet Rifle. Manufacturer: Sig Sauer ASP Model: Sig Sauer MPX ASP Materials: Metal and Nylon Fiber build. Weight: 7 Pounds (3300 Grams). Barrel: 8 inch steelrifled. Propulsion: 88 or 90 Gram CO2. Action: Semi Auto,double action only. Ammunition Type: .177 caliber pellets. Ammunition Capacity: 30 rounds belt fed. FPS: Up to 600 fps (When shot by a Unicorn)
Trigger Pull: The trigger pull on the Sig Sauer MPX ASP .177 Caliber Pellet Rifle is actually pretty decent when you consider the first part of the trigger pull is used to advance the belt fed 30 round magazine. One would think that there would be a lot of added friction from the belt but this does not seem to be the case. There is some internal blowback action going on but it is only used to cock the internal hammer/striker which does lesson the overall amount of trigger pull required. The trigger pull is shorter than expected with all that is going on and it's not overly heavy so quick and predictable action shooting is very possible with the Sig Sauer MPX ASP .177 Caliber Pellet Rifle.
Accuracy: So far I have not done my official Field Test Shooting Video for the MPX ASP .177 Caliber Pellet Rifle but I did have the chance to get out and shoot some rounds down range at my Sig provided Quad Shooting Gallery that I had setup about 35-40 feet away. Even though I did not have my red dot all perfectly sighted in I was still able to hit the smallish metal targets fairly well using the Sig Sauer MPX ASP. In terms of velocity you can expect from the Sig Sauer MPX ASP .177 Caliber Pellet Rifle, 600 fps is a bit optimistic. Sig did send me a real world fps performance spread sheet they had conducted using both 5.25 grain alloy pellets and 8.18 grain lead pellets shooting 8 rounds and averaging out the fps. The 5.25 grain pellets averaged in at just over 500 fps while the heavier 8.18 grain pellets came in with an average of just under 450 fps. Pretty much what I would expect from a shorter barreled CO2 rifle.
Build Quality: The build quality for Sig Sauer MPX ASP .177 Caliber Pellet Rifle is excellent, you can tell Sig Sauer had a lot of hands on in the design and production of this Pellet Shooting Air Rifle! The materials used and fit and finish are top notch and the mechanical function again is really good, I am kind of amazed at how well their belt fed rotary magazine design works in terms of feeding and operation. So far I have not experienced any pellet feeding problems at all using both lead and alloy flathead pellets.
Realism: The Sig Sauer MPX ASP .177 Caliber Pellet Rifle is for the most part designed to be used as a side by side optional training aid for the real steel Sig Sauer MPX Rifle. Sig wanted the pellet version to look and feel as close as posable and Sig has done a good job with this. Other than the lessor recoil and noise factor, the Sig Sauer MPX ASP .177 Caliber Pellet Rifle works and shoots much the same as a real steel Sig Sauer MPX Rifle.
Pros:
Has to be the best semi auto pellet rifle replica I have seen and shot to date.
Near perfect replica of the real steel Sig Sauer MPX including licensing and trademarks.
Awesome build quality, lots of metal parts and the nylon parts are true to form and very solid.
Rifle has been tested to shoot over 15,000 rounds reliably.
30 round full size belt fed magazine has super high capacity and works flawlessly.
Decent fps performance, about what I would expect from a multi-shot CO2pellet shooter and totally usable.
Trigger feels really good, not too long or to heavy and very consistent feel on every shot.
Fully adjustable pop up front and rear sights.
Lots of rails for your pick of sight options and other add on accessories.
Very accurate with it’s 8 inch rifled barrel.
Cons:
Rear stock is none adjustable so the gun may feel kind of cramped for larger shooters.
Internal blowback action does not advance the belt fed magazine but does cock the internal hammer.
FPS claim of 600 fps seems a bit optimistic compared to real world testing.
Comments:
I have been waiting to get my hands on the Sig Sauer MPX ASP .177 Caliber Pellet Rifle for some time now and the wait has been worth it for sure. There are really no other guns out there right now other than perhaps the Umarex CX4 Storm that compare to the Sig Sauer MPX ASP .177 Caliber Pellet Rifle and even so I feel the Sig Sauer MPX is by far the better of the two CO2 Air Rifles. OK so the MPX does not really come close to hitting 600 fps but did you really believe that in the first place? Still consistent 450 fps from a decent grain lead pellet is about what you would expect from a short barreled CO2 rifle. If you do want more fps then look at the MCX with over double the barrel length of the MPX, this will easily get you an additional 100+fps for those of you who thrive on velocity performance. I am fine with 450-500 fps since this is all that is needed to accuracy shoot and nock over most targets at a variety of ranges.
My Vimeo Table Top Review of the Sig Sauer MPX ASP .177 Caliber Pellet Rifle:
Materials: Mostly plastic with some metal construction.
Weight: 1.3 pounds (586 grams).
Barrel: 5.5 inches, non-rifled.
Propulsion: 12 gram CO2.
Action: Revolver, single & double actions.
Ammunition Type: 4.5mm steel BB's.
Ammunition Capacity: 10 rounds.
FPS: 375.
Trigger Pull: The trigger pull on the Umarex Brodax CO2 BB Revolver is actually rather nice. If you decide to cock the hammer back and shoot it single action style then you get a little bit of that SAA Revolver like ratcheting sound. The trigger pull in single action mode is short with virtually no take-up and on the light side. Double action shooting with the Umarex Brodax CO2 BB Revolver is not overly long or heavy either so action shooting is totally possible with this BB shooting CO2 revolver.
Accuracy: I can not comment so far on the shooting performance for the Umarex Brodax CO2 BB Revolversince I have not shot it yet. The weather is getting nicer outside so that should happen pretty soon. The claimed FPS for the Umarex Brodax CO2 BB Revolver is stated at only 375 which I find seems a bit low for a none blowback fairly straight forward BB pistol with an almost 6 inch barrel so hopefully my testing shows performance up into the 400's which I am hoping for. The open sights are non adjustable but there are tons more options by taking advantage of the two rails top and bottom for adding either a red dot or laser to increased target shooting ability.
Build Quality: The Umarex Brodax CO2 BB Revolver is pretty much an all metal pistol with the outer shell being made up of plastic, there is a fair bit of internal metal going on along with the trigger, hammer and of course the inner barrel made out of metal parts. Mechanically the Umarex Brodax CO2 BB Revolver feels solid and even though it only weight in at 1.3 pounds it feels much heavier in the hand.
Realism: The Umarex Brodax CO2 BB Revolver as far as I know is not an exact replica of any real steal gun currently in production. It's basically a spin off of an ultra tactical .44 magnum revolver with a super beefed up front barrel assembly sporting all kinds of accessory option to be placed on the top and bottom rails. I like that Umarex made sure to recess the barrel opening so it has a more realistic barrel size. Like many new CO2 airguns coming out these days the CO2 is not only well hidden inside the grips but a handy Allen key is built into the handle.
Not the heaviest revolver on the market but it feels really nice in the hand and has good balance, the weight is not bad at all and feels heavier than 1.3 pounds.
Trigger action is really good in both single and double action, short light single action trigger and totally usable double action trigger.
CO2 is well hidden with built in Alan key in the handle.
Rails top and bottom for all kinds of accessory add on options.
Barrel is recessed for that larger caliber look.
Nice and discreet safety.
Comes with three 10 shot easy to load rotary magazines.
Low cost with high fun factor.
Cons:
Grips are a bit hard to remove to get at the CO2, may work-in over time?
All black sights are not great on dark backgrounds and are non adjustable.
Would have liked to see fps into the 400 range.
Comments:
The Umarex Brodax CO2 BB Revolver when I first picked it up did not appeal to me all that much, maybe knowing it was for the most part yet another mostly plastic BB revolver with those thin pop in disc magazines didn't help me take notice much. But as I have been playing around with the Umarex Brodax CO2 BB Revolver it has grown on me a lot. I think it has a really cool look that is also very usable in terms of putting juts about any accessory you want on this CO2 revolver. The hammer and trigger action are also both excellent for not juts an inexpensive Airgun but even a higher end airgun. And right out of the box, or should I say clam-shell plastic wrap, you get three rotary disc magazines which is a nice bonus.
My Vimeo Table Top Review for the Umarex Brodax CO2 BB Revolver:
Action: Semi auto, single action only with blowback.
Ammunition Type: 6mm plastic BB's.
Ammunition Capacity: 16 round full size drop out magazine.
FPS: 370.
Trigger Pull: The Single Action Only trigger pull on the Umarex Elite Force Blowback CO2 Airsoft Race Gun is what you want when looking for a gun made specifically for IPSC styled shooting. The trigger is nice and light with a very short take up and crisp release. Exactly what you would be looking for when wanting to shoot accurately and quickly as in with IPSC competition shooting!
Accuracy: I have not done a field test or shooting video for the Umarex Elite Force Blowback CO2 Airsoft Race Gun so far, I am just waiting for the weather to get a little bit better but that should be soon! I woudl expect this pistol to get close to 400 fps on a warm day and pretty decent shots pre CO2 with its shorter blowback action and magazine design that seals the Airsoft BB in the breach. We will have to wait and see ot be sure...
Build Quality: The Umarex Elite Force Blowback CO2 Airsoft Race Gun is well built, it's pretty much entirely metal except for the grips and part of the full size magazine. It weighs in at a hefty 2.5 pounds so be prepared for a relatively heavy pistol but with good balance that will offset the weight of it. The tolerances are very good with very little slide wiggle the slide spring is nice and firm and the slide catch release seems to function really well, I like that the slide racking handle can be switched to either side of the gun depending on your shooting preference.
Realism: The Umarex Elite Force Blowback CO2 Airsoft Race Gun is not based on any one gun that I am aware of but overall looks the part of a real gun with all the working parts and features of a semi auto pistol of this type. You will find a full size drop out magazine is sprung to eject with force when you press the magazine release which is great for IPSC shooting. The slide catch/release will also lock the slide back on the last shot and with rails top and bottom you have several options for adding accessories.
All metal construction - good weight and very solid feeling gun.
Heavy snappy blowback action, good recoil spring tension.
Fit and finish is really nice.
Well balanced, so even with heavy blowback the gun should stay on target.
Really light, short and smooth single action trigger, for quick follow up shots.
Can take the sight rail off and install one of the two included adjustable open sight options.
Expect it to get a decent amount of shots per CO2 because of the limited blowback action and magazine design.
Would make a nice IPSC trainer.
Cons:
Comes with a red tip but may be able to take it off.
Not sure about the hop-up setup, believe it has hop-up but no way to adjust it that I could find.
Has that white waring instruction labeling on the slide, at least it is in very small print.
Comments:
Overall the Umarex Elite Force Blowback CO2 Airsoft Race Gun is a really nice competition shooting pistol and I am looking forward to getting some shooting time in with it to see if it performs as good as I believe it will. I am also hoping with it's slightly shorter blowback action and magazine design that not only will it get good fps but also a reasonable amount of shots per CO2. At this point I am not sure if am going to put a Red Dot on the sight rail or take the sight rail off and go with open metal sights, either way I pretty sure to expect fast and accurate shooting with this IPSC inspired Race Gun.
My Vimeo Video Review for the Umarex Elite Force Blowback CO2 Airsoft Race Gun:
Trigger Pull: The trigger pull on the Umarex Colt M45 CQBP Blowback CO2 BB Pistol is like the original 1911 semi auto pistol a single action only trigger. That said the Colt M45 CQBP SAO trigger is notably longer than a true 1911 trigger would be but still pretty decent overall. There is a fair bit of take up but once you get to the release point the trigger weight is about a medium pull and should allow for pretty fast action shooting with not too much finger fatigue.
Accuracy: I have not shot this "version" of the Umarex Colt M45 CQBP Blowback CO2 BB Pistol but I have high expectations that it will get much better fps and CO2 efficiency than the similar looking KWC versions out there. 400 fps for a blowback is pretty good and if it can get about 5-6 magazines worth of shots that would be close to double of what a KWC 1911 blowback gets! In terms of accuracy only time will tell when the weather perk sup here a bit and I can get outside and make some shooting videos...
Build Quality: I am very impressed with the build quality for the Umarex Colt M45 CQBP Blowback CO2 BB Pistol. In many ways it may even be better than the KWC 1911's as it seems to have a much more durable finish and the mechanical parts fit together very snug with virtually no slide wiggle at all. This little rather inexpensive 1911 blowback BB pistol should last you a long time and perform well doing it.
Realism: Up to now I have been almost preferring the Umarex Colt M45 CQBP Blowback CO2 BB Pistol over the KWC Blowback 1911 series but when it comes to realism the tables turn a little bit in favor of the KWC 1911 version. On first look it is hard to tell them both apart so yes they both look and feel very much like real steel 1911 pistols. Once you get into some more of the mechanical aspects the Umarex Colt M45 CQBP Blowback CO2 BB Pistol does make some compromises choosing to take away a little bit of the realism in favor of increasing performance. These area are the range of motion of the blowback action. On the Umarex Colt M45 CQBP Blowback CO2 BB Pistol the slide range is a bit shorter which will save on CO2 usage and the magazine is a stick mag setup which again allows for a more enclosed system again taking advantage of all the CO2 being used. Most of the mechanical parts work as you would expect them to on a real 1911 with the exception of the grip safety. The barrel is even nicely recessed ti make the barrel opening look like a real 45 auto. Lastly the trigger even though it is a true SAO trigger does extend out from the gun a lot more than a true 1911 trigger would.
Build quality and finish seem really good, excellent tolerances.
Nice snappy blowback action with a pretty heavy recoil spring.
Overall Accurate 1911 tactical styled replica in most ways.
Does have a single action only trigger, but is longer than most.
Fully Colt Licensed.
Like the white dot sights, machined hammer, ambidextrous safety and accessory rail.
Cool that the Alan key is built into the handle.
Has a believable recessed barrel.
Finished coating seems to be more durable than the actual KWC versions.
Warning instructions are color matched and not so intrusive.
Cons:
Trigger action is notably longer than a real 1911 trigger but is single action only.
No working grip safety.
Not easily field strippable.
Does not have a full size drop out metal magazine but rather a metal stick mag.
Comments:
I can never seem to get enough of the Blowback 1911 BB pistols when I have the opportunity to review them. Most of them have been just different reskinned, rebranded and redistributed version of the original KWC 1911 so it was kind of nice to get the Umarex Colt M45 CQBP Blowback CO2 BB Pistol since it offers that 1911 look with blowback action and from the looks of things it should have improved performance in the shooting department. If you have been after a Blowback 1911 BB pistol but wanted one with some more power and that you can get a decent amount of shots out of a single CO2 then the Umarex Colt M45 CQBP Blowback CO2 BB Pistol may be just what you are looking for.
My Vimeo Videos for the Umarex Colt M45 CQBP Blowback CO2 BB Pistol:
Trigger Pull: The trigger pull on the Gletcher GOLD APS Stetchkin is nice in both double and single action modes. Double action is fairly light as the hammer spring tension is moderate. The blowback operation will of course pre-cock the hammer allowing for single action shooting on almost all of your shots but the trigger pull length remains the same in both single and double action. The only difference is that in single action mode, the first part of the trigger pull, or should I say the take-up portion is much lighter until it gets to the hammer release point where you will notice more pressure and a short crisp release point.
Accuracy: I have already done a field test shooting review for the standard blowback Gletcher APS Stechkin which other than the finish is the same gun and will perform exactly the same. Make sure to checkout that shooting review for more info on how the Gletcher APS performed. In summary, I was able to get very close to the claimed 400 fps even on a rather cool early spring day (under 10 degree Celsius). I also shot with around a 2 inch 10 shot grouping from my standard target setup of 30 feet back in a semi rested position.
Build Quality: The Gletcher GOLD APS Stechkin CO2 Blowback BB Pistol is well made, the Gold and black etched finish looks really nice but may not be to everyones personal taste, kind of a love it or hate situation when it comes ot Gold guns ;) The fit is good, not a lot of slide wiggle and pretty much the entire pistol is metal including the frame, slide, trigger, slide catch-release, safety, hammer, magazine and inner barrel. The only plastic parts would be the grips, outer barrel and some internal seals and o-rings.
Realism:The GOLD CO2 BB Gletcher APS is a 1 to 1 replica of the Stechkin Soviet Military sidearm, all the mechanical parts function just like you would find on the real steel version other than the full auto mode located on the safety, which has been disabled, perhaps for the European markets where full auto airguns are not allowed. The barrel opening and the stick magazine are the real only tell-tale signs that this is the airgun version rather than a real Stechkin.
Pros:
Come in a nice Velvet lined Wooden Box.
Gold Plated with etching )either love it or hate it)
Very solid and weighty gun. Mostly all metal.
High capacity 22 round all metal stick magazine
Blowback operation is pretty heavy, slide locks back on last round.
Operational parts all work like they should (slide catch, safety, hammer, elevation adjustment, mag release)
Field Strippable.
May be able to attach a stock on it?
Shooting performance, good trigger pull, around 400 fps and got about a 2 inch grouping from 30 feet away.
Cons:
No reassessed barrel opening.
Would have liked to have seen full size drop out metal magazine on this gun.
Full auto feature disabled on safety.
Gold version is a lot more expensive than the standard blowback version. ($349 versus $179)
Comments:
When I saw this pistol in the Gletcher catalog, I did not realize how large it actually was, I was expecting the Gold Gletcher APS Stechkin to be a bit larger than the Makarov but it really does dwarf the Makarov. Being that it is a large pistol it does have some weight to it but it does not feel heavy for its size. The grips are long front to back but not overly thick side to side so even medium sized hands should be OK shooting this BB air pistol. I am really happy to see another historic airgun added to the available Replica Airguns at our disposal and it's a bonus that we also get this one with blowback operation. You do have your choice when it comes to what you are looking for in terms of finish and operation, there is of course the APS GOLD blowback BB Version being reviewed in this video, the standard black/grey none blowback APS BB version, the black/grey blowback APS BB version which again is mechanically exactly the same as the GOLD. If your prefer Airsfot you can even find a Gletcher APS Blowback Airsoft model to fit your needs. All you have to decide is which one is for you!
My Vimeo Table Top Video of the Gletcher APS Stechkin CO2 Blowback BB Pistol:
I try and make it to my local gun show which is held in Chilliwack BC about this time each year. It is put on by the Historical Arms Collectors Society of BC and there are generally a lot of used long guns (rifles) some pistols, lots of accessories, knives, hunting gear, knick·knacks and even some antique items. I tend to be looking for airguns or blank guns that are rare or a good deal.
This year I came across a few items that caught my eye. The first item was a Daisy replica 4.5mm BB pistol, I am not a big fan of Daisy replica gun in general as they are usually a far cry from the originals but this Daisy Powerline Model 400 was actually a really good copy of a Desert Eagle in size and looks. Sure it had a lot of plastic in it but it was made in Japan and even being around 20 years olds was holding up really well. This Daisy Powerline 400 even had Blowback which back then was not all that common.
The Daisy Powerline 400 BB Desert Eagle has a 20 round removable magazine that fits along the top of the barrel and it has a claimed fps. It is almost all high grade plastic with the exception of the single action only trigger, safety, hammer, barrel and several internal parts.
The next interesting item I found was a little compact 8mm blank shooter originally made in West Germany. So this blank gun is close to 30 years old. The SM Model 110 8mm Blank Pistol kind of reminds me of my EKOL Tuna in terms of size and functionality since both have the same half slide and magazine release system.
The SM Mod 110 8mm Blank Pistol is front venting and pretty much all metal with reinforced steel areas, it has a 5 round single stack magazine and shoots in single action only.
My last purchase for this show was a new item, here in Canada we generally are not allowed much in the way of items specifically labeled for self defense. There are some work arounds for instance we can carry a knife as long as it is not concealed entirely and we only intend to use it as a tool. We can also carry pepper spray again only for use on animals. Generally speaking we have not been allowed stun guns or tasers here in Canada and even importing them can land you in a lot of trouble! Again it seems a work around has been made, as long as the Stun Gun or Taser is at least 480mm in length then it is not considered a concealable weapon and as long as you have it out on display and only intend to use it on animals that may be a threat to you then all is good :)
The Stun Gun I purchased is basically a baton with a flashlight on the front and a 1 million volt taser on the front of it. You have several options with this device if harm is eminent. You can try blinding the threat with the built in flashlight which is not all that powerful but good for finding your way in dark areas, you can give the attacker a whack with the baton baseball bat style and if none of that is working well let em have the 1 million volt sandwich! We should be getting some of these Stun Baton Flashlights in our Canada Replica Airguns Store at some point so stay posted for that item.
Type: BB air pistol. Manufacturer: Umarex - KWC. Model: Colt Combat Vet Limited Edition 1911. Materials: Pretty much all metal build. Weight: 2 pounds. Barrel: 4.38 inchesBrass, non-rifled. Propulsion: CO2 x1. Action: Semi auto blowback, single action only. Ammunition Type: 4.5mm Steel BB's. Ammunition Capacity: 18-19 rounds. FPS: 320.
Trigger Pull: The trigger pull on the Umarex Colt Combat Vet Limited Edition 1911 is like all the other KWC made CO2 full blowback 1911's, it's exactly what you would expect from a real 1911 single action only pistol which helps to make this replica 1911 a great trainer. So in other words the trigger pull is super short, super light with very little take-up and a nice crisp break.
Accuracy: I have not shot this "version" of the Umarex - KWC 4.5mm BB 1911 but it will undoubtedly perform exactly like all the others. I can expect decent under 2 inch groupings from 30 feet out and will get a little over 300 fps on a full CO2 cartridges. Depending on how fast I shoot off my magazines, I should expect to get around 3 good mags and if I slow things down a bit I should get a forth magazine so anywhere from 50-70 good or so shots per CO2 out of the Umarex Colt Combat Vet Limited Edition 1911.
Build Quality: Very good, with almost all metal construction, good weight and craftsmanship, the KWC 1911 line of pistols have proven themselves over time and even though some of the original first run units had some CO2 valve issues, this seems to have been fixed over the years. You will find most of these KWC pistols in general have a rather thin coating for a finish and so they tend to wear a bit on the high spots but with this weathered Umarex Colt Combat Vet Limited Edition 1911 that really isn't a concern!
Realism: This is as close as you can come to the look, weight, feel, and action of the real 1911 in virtually almost every way including the ability to field strip this pistol! All the mechanical parts work just like they do on a real steel 1911 including the grip safety. I'm not sure what more you could ask for? The Umarex Colt Combat Vet Limited Edition 1911 even has that real gun wear and tear look to it which in my opinion even adds to the realism.
Extremely realistic airgun replica of an original Colt 1911 A1 styled 45 auto.
All metal construction - Good weight and solid feeling gun.
Would make an excellent training gun as it functions just like the real steel 1911 45 handgun.
Blowback action is very firm adding to the realism of shooting this weapon.
Field strips just like the real 1911 45 auto.
True 1911 Single action only trigger, excellent pull, very smooth and light.
Working grip safety.
Colt Licensed by Umarex
Weathering gives this pistol a very authentic look to it.
Warning instructions are nicely out of the way.
Cons:
It goes through CO2 very fast as do all the KWC full blowback pistols.
Sights are non-adjustable.
Umarex decided to label the safety, perhaps for legal reasons but it detracts from the finish.
Comments:
You would think by now I would be getting tired of reviewing yet another variation of the KWC made 1911? Nope! The Umarex Colt Combat Vet Limited Edition 1911 with it's Umarex Colt licensed and Weathered appearance adds just enough to respark my interest in these awesome CO2 Blowback 1911 replicas and every time I pick one up I get a little excited and want to go out and shoot some rounds through one :) If for some reason you have not picked up one of these 1911's to date then make sure to grab the Umarex Colt Combat Vet Limited Edition 1911 before they are all gone!
My Vimeo Videos for the Umarex Colt Combat Vet Limited Edition 1911 BB Pistol:
Trigger Pull: The ASG Dan Wesson 357 Revolver has a smoother trigger than the previous non 715 Dan Wesson Revolvers. There seems to be less of that friction while the cylinder rotates past the spring engaged inner barrel. Even the Hammer has a nicer fell to it with less side to side wiggle. Single action is really nice with a very short take up and light release point.
Accuracy: I have not had a chance to test out the ASG Dan Wesson 715 6 Inch Silver CO2 BB Revolver so far since the outside whether has been rather cold and wet. In terms of accuracy I would expect at least a 1-2 inch grouping from 30 feet out and the clamed fps of 430 seems to be in line with what we should see from the 4.5mm BB shooting Dan Wesson 715. I guess we will have to find out later on when I do my Field Test Shooting video to be sure...
Build Quality: I thought the previous generation Dan Wesson Revolvers where built really nice but the new Dan Wesson 715 takes this up several notches higher. All you need to do is pick this gun up and immediately you are in a state of wow! You almost need to ask yourself if it is in fact the Real Steal Dan Wesson 715 357 Magnum Revolver it feels that good. ASG has beefed up the barrel assembly to a solid component that adds a lot of forward weight which would be just like what you would expect from the 357 Magnum shooting version. To balance it all off the forward weight, the grips section is also reinforced with metal underneath the Hogue Styled rubber finger grips which again are another huge improvement over the plastic pistol grips found on previous models of the ASG Dan Wesson's. The stainless finish is of course awesome and this guns simply looks and feels great!
Realism: Again referencing the new ASG Dan Wesson 715 6 Inch Silver CO2 BB Revolver to it's predecessors, the Dan Wesson 715 is a true replica of the Dan Wesson 715 357 Magnum Revolver in almost every aspect and not just the Dan Wesson name. I could tell you everything that was the same but it's simply much easier to point out the only real difference I was able to point out and that would be the two pins that connect the barrel assembly to the frame of the BB version of the Dan Wesson 715. Not a deal breaker by any means and the pins really don't take away from this gun in my opinion.
Another great shell loading revolver, perhaps one of the nicest modern BB revolvers to date!
Almost all metal design, super heavy, feels like a real gun in the hand.
Lots of detail in this gun, very well made, fit and finish is excellent.
Dan Wesson Licensed and an excellent replica overall.
Adjustable rear sight for windage and elevation.
Rubber Hogue style finger grips, huge improvement over previous Dan Wesson grips.
Well hidden CO2 screw and Allen key built into the removable grip.
Much improved hammer and trigger action, smoother trigger and less wiggle in hammer.
Barrel opening is very realistic, even has simulated rifling.
Safety design is well hidden and easy to use.
Cons:
Two pins to attach the barrel assembly to the frame are not in line with the real steel version.
Trigger still has a bit of that initial friction in double action mode because of the spring loaded internal barrel.
Comments:
I was already a big fan of the Dan Wesson line of Revolvers, this new 715 version of the Dan Wesson takes it to a whole new level! In terms of the modern shell loading CO2 Revolvers out there the ASG Dan Wesson 715 6 Inch Silver CO2 BB Revolver is by far my new favorite. ASG completely redesign their new ASG Dan Wesson 715 6 Inch Silver CO2 BB Revolver basing it entirely on the real steel version and capturing the quality, look and feel nearly exactly. if you already have a Dan Wesson Revolver and think that perhaps you can pass the new version by, well I would think again or you may be missing out on one of the best BB Revolvers out there at this time.
My Vimeo Video Table Top Review for the Dan Wesson 715 CO2 BB Revolver:
I am showcasing here on the Replica Airguns website and over on the Replica Airguns YouTube channel a series of videos I will be making for the purpose of selling some guns out of my personal collection. I simply have no more room for the new guns and in some cases I either have duplicate guns or very similar versions so there is no need to have both. Some guns I am less attached to and as I already stated I need to make room for some of the new stuff I will be reviewing and or buying for myself.
In this second Mike's Personal Guns For Sale video I am offering three rifles, two of which will require a Canada PAL Firearms License since one is a 22LR rimfire rifle and the other is a high powered .22 caliber break barrel pellet rifle. The last item up for bid is an AK-47 styled .68 caliber paintball rifle.
Make sure to watch my above YouTube video to see these three rifles I am selling and instructions on how you can take part in the sale and purchase of them. By the way I am only selling to Canadian residents since shipping cross borders is a little sketchy.
Here is a list of the these three rifles I am selling from my personal gun collection:
