Type: Pellet air revolver.

Distributed by:UmarexUSA.

Model:Single Action Army Revolver with Colt licensing

Materials: Mostly metal with plastic grips.

Weight: 2.35 pounds (1070  grams).

Barrel: 6.75 inches rifled.

Propulsion: 12 gram CO2.

Action: Revolver, single action only.

Ammunition Type: .177 cal. pellets.

Ammunition Capacity: 6 rounds.

FPS: 380.

Trigger Pull: Trigger pull on all the Umarex Single Action Army BB and Pellet Revolver is really great. Being that these Single Action Army Revolvers are single action only, most of the work is done while you pre-cock the hammer with your thumb. The trigger single action pull is under 2 pounds and has virtually no take up with a crisp release. I love the ratcheting sound of the cylinder as you pull back the hammer just like using a real SAA Revolver!

Accuracy: I have not yet tested the Umarex Colt Single Action Army Nickel & Gold Pellet Revolver so far but expect it to perform very similarly to the 4.5 inch barreled pellet shooting version I tested a while back. On that Field Test Shooting review I was abel to get pretty close to the claimed fps with an average of 378 fps. During my accuracy portion shooting from 30 feet back onto a paper target I got a very respectable .75 inch 6 shot grouping using a semi rested position. I do expect the slightly longer barrel on the Nickel and Gold version to perhaps improve fps slightly.

Build Quality: All of the Colt Single Action Army BB and Pellet Revolvers have a mostly all metal construction other than the plastic grips and any seals. The fit and finish is excellent with a great overall weight in the hand. The mechanical action of the hammer and trigger feels just like it would on a real single action army revolver. I really like the two tone nickel and Gold finish on this longer barreled SAA revolver.

Realism: In terms of replicating a real steel Colt Single Action Army Revolver, again these Umarex old west 6 shooters are absolutely amazing replicas. It's really hard to tell the airgun version apart from the real steel version, with the exception of the smaller diameter shells and the discreet safety switch located under the frame. Even the barrel is nicely recessed and has some fake rifling twists in it to give the appearance of a large caliber barrel opening. The CO2 is well hidden with the Allen key built into the handle so no ugly CO2 screw tab hanging down.

Available in the:Replica Airguns Store

Pros:

• Still the best airgun reproduction of the Single Action Army Revolver, a very accurate replica of the real steel old west version.

• Nice large caliber Recessed barrel.

• Great weight and feel in the hand.

• Shell loading design that loads from the back so no need to remove shells if you wish not to.

• Hammer and trigger action is about perfect, no take-up, very crisp and super light (under 2 pounds).

• Nickel and Gold finish looks really great!

• Colt licensing via Umarex.

• Very well concealed CO2 with built in Allen key.

• Discreet safety location under the frame.

• Longer barrel is unique and should get a bit higher fps than the standard  shorter barreled versions.

Cons:

• A lot more expensive than the standard barrel length in standard finishes.

• Real version would shoot 45 caliber, dummy shells are actual closer to 357 so a bit smallish.

• The safety in all of these ghost is really firm and hard to change.

Comments:

We have pretty much established that these Umarex Colt Single Action Army pistols are fantastic airgun copies of the old west real steel 6 shooters in pretty much every way. For this reason they have been super popular! The Umarex Colt Single Action Army Nickel & Gold Pellet Revolver is yet another rendition of this same airgun but with a longer barrel and the tow tone Gold and Nickel finish. You will pay a bunch more for the longer barrel and two tone finish, is it worth it? If your on a budget perhaps not but if you want something that really stands out and may even perform just a little better than pony up the extra bucks and pick one of these beauties up.

My Vimeo Table Top Review for the Umarex Colt Single Action Army Nickel & Gold Pellet Revolver:

Buy the Umarex Colt SAA Pellet Revolver in Canada

Type: Blowback Airsoft Pistol.

Manufacturer:KJWORKS Distributed by ASG

Model:X9 Classic

Materials: Metal slide & frame.

Weight: 2.1 pounds (950 grams).

Barrel: Metalnon-rifled smooth bore.

Propulsion: 12 gram CO2.

Action: Blowback, single and double action.

Ammunition Type: 4.5mm steel BB's.

Ammunition Capacity: 16 rounds.

FPS: 312+ fps.

Trigger Pull: The trigger pull on the ASG/KJWorks Beretta X9 Classic is very good in both single and double action. Double action is a bit longer and heavier than when shooting in single action since the hammer is being drawn back, but not overly heavy by any means. Single action shooting is short, light and crisp as you would expect when shooting a real steel Beretta 92 style pistol.

Accuracy: I have not done my actual Field Test Shooting video review for the ASG/KJWorks Beretta X9 Classic CO2 BB Pistol but I did get the chance to make a short preview video where I shot the Airsoft version of this M9 Beretta at some clay pigeons setup around 20 feet away. I was able to pop the center out of the clay pigeons no problem and found that even without any practice I was consistently hitting dead center on most shots. I am not sure exactly what the FPS will be btu it shoudl for sure get at least the claimed 312 fps if not a bit more.

Build Quality: As expected, the ASG X9 Classic Beretta M9 CO2 Blowback 4.5mm BB Pistol build quality is just like all the other KJWorks Airsoft guns I've tested so far. The ASG 4.5mm Steel BB shooting X9 Classic has more of a Matt finish but I kind of like it, not so many finger prints on the gun. All  the tolerances between the moving parts like the slide and frame are very tight showing excellent workmanship and machining from KJWorks.

Realism: The ASG X9 Classic Beretta M9 CO2 Blowback 4.5mm BB Pistol is an excellent copy of the real steel popular Beretta M9, it is really hard to tell it apart from the real version and the ASG X9 Classic can even be field stripped in the same manor as a real Beretta M9 Semi Auto pistol with the similar functioning parts. The only missing aspect would be Beretta Licensing since the ASG version is unlicensed.

Available in the:Replica Airguns Store

Pros:

• No ugly white warning instructions on the slide.

• Really nice replica of the original Beretta M9.

• Great weight and feel to it.

• All metal design, fit and finish is very good as is with all KJWorks made guns.

• Strong slide spring so should have nice heavy blowback action.

• Realistic working safety and working slide catch and release.

• Full size dropout metal magazine that holds steel BB's and CO2.

• Can be field stripped like original Beretta M9.

• KJWorks quality.

Cons:

• Not licensed like the Umarex version.

• None adjustable sights and white dot sights are kind of light.

• Will eat up CO2 pretty quickly. 

Comments:

There are very few 4.5mm Steel BB guns made by KJWorks and it seems that ASG as far as I know is the only distributer that has teamed up with KJWork to have them make some of their guns, I reviewed the ASG CZ 75 which is another ASG/KJWorks distributer 4.5mm CO2 Blowback Pistol. I don't even think you can get the 4.5mm Steel BB shooting version direct from KJWork? What I love most of all about the ASG X9 Classic Beretta M9 CO2 Blowback 4.5mm BB Pistol is that it is made by KJWorks since there are already a lot of Beretta M9's and Mod. 92's already out there but if I could only have one it would probably be the ASG X9 Classsic!

My Vimeo Table Top  Review of the ASG X9 Classic Beretta M9 CO2 Blowback 4.5mm BB Pistol:

Buy the ASG X9 Classic BB Pistol in Canada

Buy the ASG X9 Classic BB Pistol in the US

I have some new guns for everyone to checkout which is always good for everyone, especially me :)

In this update video I show you around three pistols one Arisoft Rifle. With the pistols we have a mixed bag of Pellet, steel BB and plastic Airsoft. First off I take a look at the ASG X9 Classis Beretta M9 CO2 Blowback 4.5mm Steel BB pistol, which by the way is actually made by KJWorks so we know this it's going to be a quality gun! I then switch things up and showoff the new long barrel CO2 powered Umarex Colt Peacemaker SAA pellet revolver that sports a Nickel and Gold finish. Last for the pistols we take a look at the 6mm Airsoft firing Colt 1911 Rail Gun in the Dark Earth finish, it's basically a KWC 1911 but with a little extra bling.

Last but now least to show you in this update video is the ASG CZ Scorpion EVO 3 A1. This product was developed by ASG in cooperation with CZ and is made to give the Airsoft Player the closest shooting experience they can possibly get to handling and shooting a real CZ Scorpion EVO 3 A1!

ASG X9 Classic Beretta Blowback CO2 BB Pistol:

• Full metal

• 4.5mm steel BB's

• Full blowback action

• 2.1 pounds

• 16 Round full size drop out metal magazine

• 312 fps

• Single & double action

Umarex SAA Colt Peacemaker Nickel & Gold Co2 Pellet Revolver:

• Full metal

• .177 caliber pellets

• Gold highlighted cylinder, hammer & trigger

• 6.75 inch barrel

• Shell loading 6 shooter

• 380 fps

• Single action only

Colt 1911 Rail Gun Dark Earth Blowback CO2 Airsoft Pistol:

• Full metal

• 6mm Airsoft BB's

• Comes with red tip but can be removed with some work

• Full blowback action

• 2.1 pounds

• 17 Round full size drop out metal magazine

• 345 fps

• Single action only

ASG CZ Scorpion EVO 3 A1 AEG Airsoft Rifle:

• Metal & plastic build

• 6mm Airsoft BB's

• Comes with red tip but can be removed easily

• AEG: single shot, 3 round and full auto shooting modes

• 5.3 pounds

• 75 Round magazine

• 394 fps

• Full CZ licensed

Buy Umarex SAA Colt Peacemaker Nickel & Gold Co2 Pellet Revolver in Canada

Buy ASG X9 Classic Beretta Blowback CO2 BB Pistol in Canada

Buy ASG X9 Classic Beretta Blowback CO2 BB Pistol in the US

Buy Colt 1911 Rail Gun Dark Earth Blowback CO2 Airsoft Pistol in Canada

Buy Colt 1911 Rail Gun Dark Earth Blowback CO2 Airsoft Pistol in the US

Buy ASG CZ Scorpion EVO 3 A1 AEG Airsoft Rifle in Canada

Buy ASG CZ Scorpion EVO 3 A1 AEG Airsoft Rifle in the US

First off, I want to thank Crosman for providing these two guns for review! Now they're not exactly new guns by any means but for sure worth showing and doing some update reviews for.

Starting with the Crosman PFAM98 Taurus PT-92:

The Crosman PFAM98 Taurus PT-92 is essential a KWC made M92 also branded as the same gun as the Cybergun GSG 92 and the Swiss Arms P92.

So for all intense and purposes if you have watched any of my other revise on this line of KWC Beretta /Taurus BB pistols and even Airsoft versions then this BB gun should be really familiar to you.

History of the Taurus PT-92:

It is often referred to as a Berate 92 copy but in fact it is a Taurus PT-92 replica. The Taurus PT-92 is a product of Brazil, Taurus actually bought the entire Brazilian Beretta factory back in 1980 including drawings, tooling, machinery, and a very experienced work force to make the guns. Taurusimmediately sought to improve on the Beretta design, resulting in the popular and acclaimed Taurus PT-92.

Specifications for the Crosman PFAM98 Taurus PT-92:

• Full Blowback operation.

• Full metal frame, slide and magazine.

• 12 gram CO2.

• 4.5mm steel BB’s.

• 20 shot full size drop out metal magazine.

• Smooth bore barrel.

• Single and double action trigger.

• 2.44 pounds (1107 grams).

• Up to 400fps.

• Replica of Taurus PT-92.

• Made for Crosman by KWC in Taiwan.

Next up the Crosman American Classic P1322.

The American Classic P1322 is basically a .22 caliber version of the .177 caliber 1377 Pneumatic Pump Air Pistol. So make sure to watch the video reviews I have already done for the Crosman American Classic P1377. Other than caliber the .22 caliber version at least in Canada is more powerful since it has not been detuned for Canada import. The .22 caliber version has a claimed fps of 460 which is under our 500 fps import limitation while the standard non detuned .177 caliber version has a max claimed fps of up to 600 which can set off alarms at customs. For this reason the Crosman American Classic P1377 Canada version is detuned to shoot under 500 fps.

Crosman use to make a similar version of the Crosman American Classic P1322 called the Back Packer which had a slightly longer barrel and came with a removable stock. You can kind of replicate this gun by adding the stock but it will have a shorter barrel. Keep in mind there are a ton of mods available for this series of Crosman airguns including barrels, bolts, trigger, Internals stocks, scope mounts…

PHOTOSpecifications for the Crosman American Classic P1322:

• Metal and plastic construction.

• Pneumatic pump.

• .22 caliber lead pellets.

• Single shot bolt action.

• Rifled metal barrel.

• Single action only.

• Up to 460fps using lead pellets (10 pumps).

• 1.88 pounds (853 grams)

Keep posted for my full update reviews for these airguns...

This year at SHOT Show 2017 in Las Vegas, I found there wasn’t a lot of new Airgun products but as always there are some that stood out for me. If you want more info on each Airgun Company then make sure to watch my full interviews for this years SHOT Show 2017. So without prolonging this video any longer let’s get right into it…

Umarex Legends MP CO2 Full Auto German MP40 Replica Machine-gun:

What’s not to like about the Umarex Legends MP? It has lots of metal parts weighing in at 7.7 pounds, a 60 round steel BB magazine with a dual 12 gram CO2 system. You also get your choice of shooting either in semi auto or full auto at up to 400 fps. Personally the Umarex Legends MP was the most interesting Airgun at the show this year for me and I really think it is going to be a hit!

Umarex SA10 Blowback Pellet and BB CO2 Pistol:

Another interesting product from Umarex this year was the SA10, I am not really sure what it is exactly styled after, it’s more of a futuristic looking gun with slide venting and a thread barrel for adding a mock suppressor or compensator. What appealed to me most about the Umarex SA10 was the new magazine design that incorporates a full size drop out metal magazine with 4 rotary 8 round magazines that can be loaded with either pellets or BB’s. When you empty one 8 shot magazine you simply drop the entire mag out and swap your empty 8 shot rotary magazine for a full one. The SA10 has a nice weight of around 2 pounds and shoots up to 426 fps.

Sig Sauer ASP P320 CO2 Blowback Pellet Pistol:

Sig Sauer introduced their new Sig Sauer ASP P320 CO2 Pellet Pistol this year that will be replacing the P250. Like the P250 the Sig P320 has a metal slide and polymer frame but instead of a double sided 16 shot rotary magazine, the Sig ASP P320 has a newly designed and very unique 30 round belt fed magazine. That’s nearly double the capacity without having to flip the magazine around part way through shooting. It’s great to see innovations like this happening in the airgun market.

Crosman Remington 1875 Shell Loading CO2 Pellet and BB Revolver:

Crosman introduced their own Single Action Old West Revolver this year in the form of the Remington 1875. Like the super popular Umarex Single Action Army Revolvers, the Remington 1875 is also shell loading and uses 12 gram CO2. You have the option of shooting either Pellets or BB’s out of its smooth bore barrel. I expect the Crosman Remington 1875 Shell Loading Revolver to be another popular Old West Airgun Revolver.

Crosman PSM45 Single Shot Spring Powered BB Pistol:

The Crosman PSM45 at first glance may not seem that interesting, after all it’s all plastic on the outside and only shoots about 200 fps! On the plus side it kind of looks like a Glock and we all know how hard it is to find airguns these days that resemble a Glock. I also like the fact that there is no need for any CO2, and most springers out there look like springers while the Crosman PSM45 looks like a real semi auto pistol. The PSM45 even has pretty decent weight to it since there are lots of internal metal parts and a full size drop out metal magazine which was a real surprise in such an entry level low cost pistol. If you’re looking for a fun inexpensive replica plinker than the Crosman PSM45 should fit the bill. On a side not the PSM45 would also make a really great low cost prop since the slide does work and it has that full size drop out magazine!

ASG Dan Wesson 715 2.5 and 4 inch Shell Loading CO2 Revolvers:

The ASG Dan Wesson Revolver has always been a popular choice, and then the Dan Wesson 715 came out improving on the design by adding extra weight and smoothing out the mechanics. How do you top that? Well by giving us some more options like barrel lengths. You now have your choice of a 2.5, 4 or 6 inch barrel for the Dan Wesson 715 and of course you will be able to buy your 715 pick in 4.5mm Steel BB, 6mm Plastic Airsoft or .177 Caliber Pellet ammunition versions. My personal choice may be the 4 inch Dan Wesson 715 since it has the addition of an integrated accessory rail machined into the outer barrel for lasers or tach lights.

Gletcher M1944 Mosin Nogant CO2 BB Rifle:

The Gletcher M1944 Mosin Nogant CO2 BB Rifle is not a new replica gun this year but it has been a hard one to get your hands on. In fact up until SHOT Show 2017 I had never seen one in person and so the Gletcher M1944 is new to me. I was very impressed with the quality of the Gletcher M1944 Mosin Nogant, it has a lot of metal parts including the swing out bayonet and even the simulated wood stock looks like real wood. I even had to take a second look and ask before confirming that the stock is in fact plastic on the Gletcher M1944 Mosin Nogant. I am looking forward to reviewing this rifle in the future when I do finally get one!

Of course there where other interesting products at SHOT Show 2017 this year but those are the products that stood out the most for me. Again make sure to watch my full interview videos to find out more about all the new products at this years SHOT Show.

And finally my last Vimeo video from SHOT Show 2017 in Las Vegas! Sorry there is no Interview this time with KWA but I did talk a lot with the KWA folks over at SHOT Show this year and I even got to test out their Laser Targeting System designed to be used with several specifi KWA guns by laser-ammo.com.

Unfortunately we don't carry the KWA brand in the replica Airguns store, a few models sneak in when being distriubted by another company like ASG in the case of the ASG MP9. I would love to carry KWA Airsoft Products in the future since they really do make very high quality Airsoft guns.

KWA has a great selection of Airsoft pistols and rifles in both Gas Blowback and AEG formats. The quality reminds me of the KJWors Airsoft guns we sell in the Replica Airguns Canada Store, you can really feel the quality when you pick them up and hold them for yourself.

My last Interview for SHOT Show 2017 in Las Vegas, well at least till next year and I am already looking forward to going back and doing it all over again :) I met with Boris Shekhman from Gletcher and Boris showed me several of their Gletcher Airguns along with a new accessory introduced this year.

Probably the highlight at the Gletcher booth was the Gletcher M1944 Mosin Nagant CO2 4.5mm Steel BB Bolt Action full stock air rifle! I already reviewed the Gletcher M1891 short stock version but have been really looking forward to seeing the Gletcher M1944 Mosin Nagant in person. Interestingly, Boris was asked by the SHOT Show staff to remove the Gletcher M1944 Mosin Nagant from his display because the real metal swing out bayonet was a concern for them. Boris was kind enough to bring out the Gletcher M1944 for me to see and video for everyone. The full stock however is not real wood but you need to look super close to figure this out as the reproduction is incredible.

We took a look at another Gletcher Airgun I have reviewed in the past, the Gletcher NGT and Gletcher NGT R which are very acurate Steel BB and Pellet shooting reproductions of the Belgian Nagant Revolver. Both these BB and Pellet shooting NGT's are getting a slight make-over with the addition of a safety on them, the real steel versions do not have a safety but some dealers felt it was a concern so Gletcher moving forward will be including a safety on all new NGT's. So if you want a more original Gletcher NGT Nagant Revolver then hurry up and pickup the older non-safety versions while they are still available!

Last on the list of new products from Gletcher are some really great looking leather holsters that not only work for several Gletcher airgun products but can also be used for the same real steel versions. Some of the pistols these new leather holsters will accommodate are the Gletcher TT Tokarev, 1911, Grach, PM 1951 Makarov, and the Stechkin.

Enjoy my latest SHOT Show Interview with Jesse Caster from Crosman. Jesse shows me Crosman’s latest old west single action revolver, the Remington 1875 which shares a lot with the super popular Colt Single Action Army revolvers. Jesse also goes over some new airgun pistols with me, a CO2 powered non blowback 1 to 1 replica of the Remington RP45, a very interesting single shot spring piston “Glock-ish looking pistol called the PSM45. And last but not least, Crosman has now got on the Beretta / Taurus bandwagon and added the PFAM98 to their lineup.

Crosman’s new Remington 1875 should be a welcome addition for anyone looking to add something new to their Old West Airgun lineup. The Crosman Remington 1875 like the Colt Single Action Army Revolver is shell loading, shoots in single action only and has that super slick ratcheting cylinder we all love. The Crosman Remington 1875 shoots both .177 caliber pellets and 4.5 mm steel BB’s from its smooth bore barrel, but Jesse has gone on record to claim that the pellets work well and shoots pellets and BB’s accurately at ranges typical for this type of Airgun.

Another Remington Licensed Airgun from Crosman this year is the Remington PR45. The PR45 is a 1 to 1 replica of the real steal Remington RP45 but in a CO2 non-blowback 4.5mm BB shooting version. The Crosman PR45 has a metal slide and polymer frame with a drop out all metal stick magazine. Some other notable features for the Crosman PR45 are a working trigger safety and white dot sights front and back.

If you are looking for something a little different from Crosman this year then checkout the single shot spring piston PSM45. This super affordable air pistol kind of looks "similar" to a Glock and lord knows how many times I get asked what is available in an airgun that resembles a Glock. The Crosman PSM45 is not going to win any fps awards (shoots around 200 fps), but there is no need to buy any CO2 and you can shoot this airgun in virtually any temperature for only the cost of steel BB’s. The frame and slide on the Crosman PSM45 are plastic but it does have decent weight do some internal metal parts and an unexpected full metal full size drop out magazine.

Crosman this year is adding a Beretta/Taurus full metal and full blowback CO2 BB Pistol to their product lineup. You may have already guessed it, it’s essentially a KWC Beretta / Taurus which really isn’t a bad thing since the KWC Blowback Beretta / Taurus has been very popular with replica airguners. A nice little treat with the Crosman PFAM98 Beretta / Taurus is that right out of the box it shoots in both semi and full auto using the ambidextrous selector safety switch.

Another SHOT Show 2017 interview video, this interview is with Bob Li from ASG (Action Sport Games), Bob shares with me some updates to the super popular Dan Wesson 715 along with the reintroduced EVO Scorpion Inferno powered Airsoft Rifle. Bob finishes up with a new X9 Classic which is a Beretta M9 in 4.5mm Steel BB.

You may have thought the Dan Wesson 715 was already pretty much perfect as is so what could ASG to make it even better? How about different barrel lengths. ASG has introduce the Dan Wesson 715 in both a new 2.5 inch and 4 inch version. Both lengths will be hitting stores shortly and will come in .177 caliber pellet and 4.5mm steel BB options. 6mm Airsoft will be out later on. The 4 inch version also includes an integrated accessory rail machined into the outer barrel for those of you wanted to add items like lasers and tactical lights to your Dan Wesson 715.

Last year at SHOT Show ASG introduced the EVO CZ Scorpion 3 A1 Inferno powered Airsoft Rifle but is again reintroducing it this year since they decided to take their time and get it perfect before releasing it in stores this March. The EVO CZ Scorpion 3 A1 is Inferno powered using an HPA system with a custom chip set that allows for a three round burst option an empty magazine detection.

ASG has sourced out not just any 4.5mm Steel BB shooting M9, they are actually getting their new ASG X9 Classic built by KJWorks. KJWorks is known for their Airsoft guns and I have reviewed several of them to date. If you have been looking for a KJWorks M9 but would prefer it to be in 4.5mm Steel BB then the new X9 Classic 4.5mm Steel BB KJWorks M9 exclusive to ASG is where you can get one!

Next up from SHOT Show 2017 in Las vegas, I bring you my Umarex Interview with Bradley Burgin! Bradley showcases two new pistol from Umarex Airguns. First we take a look at the Umarex SA10 CO2 Blowback Pellet and BB Pistol. The Umarex SA10 has a unique full size drop our metal magazine that not only holds the CO2 but also houses 4 8 shot rotary magazines that can be pre loaded and then hot swapped as required. Each 8 shot rotary magazine can be loaded with either 4.5mm Steel BB's or .177 caliber pellets. The Umarex SA10 comes in at a hefty 2 pounds and can shoot up to 426 fps. The barrel is also threaded for attaching an optional mock silencer.

Next up Bradley showed me the ultra realistic and fully licensed Beretta APX which is a Blowback CO2 BB Pistol that like its real steel big brother has a locking metal slide and polymer frame. The Umarex Beretta APX has a 19 round stick magazine and shoots 4.5mm steel BB's at 400 fps.

Last but not least and perhaps the most exciting product from Umarex for me was the Umarex Legends MP. The Legends MP is a replica of the German MP40 submachine gun and even has semi and full auto selectability! The Umarex Legends MP is a mostly metal rifle and comes in at 7.7 pounds. The full size magazine holds two CO2 cartridges along with 60 4.5mm steel BB's for an almost endless supply of ammo :) The Umarex Legends MP like the real German MP40 has a metal folding stock and propels steel BB's at 400 fps.

My First SHOT Show 2017 Las Vegas Interview to kick things off! Dani Navickas from Sig Sauer ASP talks with me about three new CO2 blowback air pistols Sig Sauer ASP is introducing this year just in time for spring season.

The Sig Sauer ASP P320 will be replacing last years P250, don't worry the Sig Sauer ASP P226 is not going anywhere! The P320 is a CO2 Blowback Pellet pistol similar to the previous P250 but this new model has a 30 round belt fed magazine rather than a dual sided 16 round rotary magazine. I love that Sig Sauer ASP is coming out with new innovations like this for us Airgun enthusiasts! The Sig Sauer ASP P320 has a metal slide and polymer frame like it's big powder burning brother and throws pellets at around 430 fps average. Don't expect a ton of shots per CO2, you will be lucky to get two magazine out of a single 12 gram CO2 but I am sure the extra power is worth it.

Sig Sauer ASP also introduced this year two new full metal and full blowback CO2 BB firing 1911's that feature a working safety and grip safety along with a true single action trigger. You have your choice of the signatured Max Michel in two tone black and silver or the Spartan in a Gold Brown finish. Both of these guns are based on the same mechanical build but are cosmetically different. I can say they feel really good in the hand and are super solid. There is a bit of a trade off, you do get a bit higher fps (around 410 fps) than some other 1911's at out there but you will have to put up with a stick magazine.

Of course the Sig Sauer ASP MPX and MCX are still going strong alone with the Sig Sauer ASP P266. Make sure to watch my previous Review Video for the Sig Sauer APS MPX and Sig Sauer APS P226.

Enjoy some additional photos along with my Vimeo Sig Sauer SHOT Show 2017 Interview!

Type: Airsoft Pistol.

Manufacturer:Umarex.

Model:H&K USP.

Materials: Mostly clear plastic exterior with metal magazine and internal metal parts.

Weight: 1.2 pounds (544 grams).

Barrel: 4 inches, metal non-rifled with internal Hop-up.

Propulsion: CO2 x 1.

Action: Semi auto, double action only.

Ammunition Type: 6mm Plastic BB's.

Ammunition Capacity: 16 round full size drop out magazine.

FPS: 360 (.12 gram BB's).

Trigger Pull: The trigger pull on the Umarex HK USP Clear CO2 Airsoft Gun is pretty light for a Double Action Only trigger and it will allow for some pretty quick rapid fire action shooting. The hammer is basically for show as the hammer is actually situated internally.

Accuracy: So far I have not had a chance to test the Umarex HK USP Clear CO2 Airsoft Gun out but I expect it to get around 300 fps using .20 gram plastic Airsoft BB's and with the internal hop-up it should also be fairly accurate. We will have to find out later on when I get outside and perform my Field Test Shooting Video Review.

Build Quality: My first impressions of a clear plastic gun are that it is going to be cheaply made but this is not the case with the Umarex HK USP Clear CO2 Airsoft Gun. For the most part it is exactly like the all black Steel BB version I already reviewed other than the clear plastic shell. Everything else about the Umarex HK USP Clear CO2 Airsoft Gun is the same and there is a lot internal metal parts including a metal barrel and breach and a full internal metal chassis. I would have like to have seen a metal trigger, hammer, safety and slide catch release.

Realism: The Umarex HK USP Clear CO2 Airsoft Gun is a fully licensed replica of the real H&K USP automatic pistol. Other than it being clear and having a red tip is an extremely close looking and accurate replica of the real steel version. It does not operate the same since it is non blowback and does not have a moving slide but visually it is a very good copy.

Purchased this gun from: The Replica Airguns Store.

Pros:

• Relatively low cost gun, even less than the Steel BB version that is the same other than the clear plastic portions.

• Nice full size drop out magazine that holds the CO2 and Airsoft BB’s.

• Lots of internal metal parts gives decent weight to the gun even though much of the shell is plastic.

• Rail for accessories.

• CO2 screw is well hidden in magazine.

• H&K licensing via Umarex.

• Red dot sights are easy to see on most targets.

• Should have justthe right amount of power for indoor CQB style Airsoft games.

• Makes a good starter pistol for someone getting into the hobby that may not want a gun that looks too realistic. 

Cons:

• Being a clear gun obviously takes away from the realism but that is the point of this gun so as not be confused with a real gun..

• Would have been nice if the magazine was metal like earlier versions of the HK USP.

• Also would have been nice to see more metal parts like the hammer, magazine release, safety, and slide catch release.

Comments:

As I mentioned in my video of the Umarex P99 Clear Plastic Spring Airsoft Pistol, I can be a bit of an Airgun snob and I tend to stay away from the clear Airsoft guns since I like mostly metal guns with blowback operation. That said there is a place for these clear Airsoft pistols. The Umarex HK USP Clear CO2 Airsoft Gun other than being clear looks like a gun and shoots like a gun but will not be confused as being a real gun which can offer some more safety and less stress to all parties involved.

My Vimeo Video Review for the Umarex HK USP Clear CO2 Airsoft Gun:

Buy the Umarex HK USP Clear CO2 Airsoft Gun in Canada

Buy the Umarex HK USP Clear CO2 Airsoft Gun in the US

It's been a great year for Replica Airguns and I wanted to share with everyone some of my favorites that I reviewed this year. In this Vimeo Video I show some of my top Replica Airgun picks for 2016 and talk a little bit about each one and what I like about it.

Here is a list of the Replica Airguns in this lineup:

• ASG Dan Wesson 715 CO2 Revolver - Comes in 4.5mm Steel BB, 6mm Plastic Airsoft & .177 Pellet.

• Umarex Colt Combat Vet CO2 Blowback 1911 - 4.5mm Steel BB.

• Sig Sauer MPX ASP CO2 Rifle - .177 Pellet.

• Sig Sauer ASP P226 CO2 Blowback Pistol - .177 Pellets.

• Air Venturi ISSC M22 CO2 Blowback Pistol - 4.5mm Steel BB.

• KJWorks KC-02 V2 Ruger 10/22 GBB Rifle - 6mm Plastic Airsoft.

• Umarex S&W M&P40 CO2 Blowback Pistol - 4.5mm Steel BB.

This has got to be one of the most asked questions when people are trying to decide on which CO2 BB Pistol they want to buy. The reality is that most non blowback CO2 BB pistols will generally shoot just over 400 fps and most blowback BB pistols will shoot around 350 fps. Some may shoot a little faster and some may shoot a little slower.

My question is this… What difference will it make if you are shooting a BB at 350 fps versus say 450 fps? I honesty think that some people believe that if they purchase a CO2 BB pistol that shoots a whopping 499 fps, then they have acquired a deadly weapon with crazy stopping power.

The truth of the matter is that even a 500 fps BB gun is still not suitable for even small pest control or hunting, you would only be causing the animal to suffer if you shot it with such a lower powered airgun. So using an air pistol for any kind of personal protection on human sized targets is completely out off the question.

Let’s talk about what CO2 BB pistols are really used for. Shooting at pop cans, shooting paper targets, perhaps setting up some army men and  picking them off one by one. stuff like that. So does it really matter if the BB is going 350 fps versus 450 fps? It’s still going to go clean though a pop can even filled with water, paper is no match for a BB traveling even under 300 fps, and Army men stand no chance when head shot by a steel BB the size of a canon ball to them.

When is power really going to be important in a CO2 BB Pistol? Perhaps if you plan to shoot out at longer ranges but in this case Steel BB’s are not really meant to shoot out at long ranges as most BB pistols do not have rifled barrels meant for long range accuracy. I have found Steel BB guns to be very accurate up to 30 feet or so, even grouping within in a half inch with some CO2 BB pistols, but further out than that and the BB’s start to wander.

Normally higher velocity is what you want when you plan on using your airgun for hunting or pest control but again a CO2 BB pistol simply is not the tool for this job.

One comment I hear a lot from people is that they would prefer more power over blowback action and that they feel that blowback action robs the gun of too much power. Yes blowback does sacrifice some power since it uses a little bit of the CO2 to operate the slide but the benefits of blowback in my opinion are worth the 50 or so fps loss in power. Blowback operation adds realism to the CO2 BB gun simulating recoil, allowing true single action trigger operation and many CO2 BB Pistols will even lock the slide back on the last shot so you know you are out of ammo and can practice your magazine drop and reloading.

One of the most common types of question I get on my Replica Airguns YouTube channel has to be something like… Why is my Airgun not working? Most of the time the amount of info about the problem is limited to something like… “It was working yesterday but now it’s not working anymore” or something like “when I pull the trigger nothing happens”. My personal favorite is… “I took my gun apart and now it doesn’t work!”

I just made a similar video for Blank Guns and as I said in that video, trying to trouble shoot a mechanical or technical problem over the internet is very difficult, this goes for cars, guns, computers or what have you…

In this Why is My CO2 Airgun Not Working video I will however cover some of the more common and obvious problems I have seen relating to why a CO2 Airgun may not be working properly. I really don’t get a lot of questions about Spring Piston or Pump Airguns so I will be focusing on CO2 Airguns in this video. There will be a lot of crossover with CO2 Airsoft guns so this video may be helpful for some of you Airsofters out there

First let’s get the super obvious stuff out of the way! 

• Did you put a new CO2 cartridge in it and is it pierced all the way?

• Did you load BB’s or Pellets into the Airguns magazine and is the magazine in the gun correctly?

• Is the safety off?

• If the gun is a blowback semi auto single action Airgun then did you pull the slide back prior to the first shot?

CO2 Related Problems:

Not all CO2 cartridges are created equal, they often have slightly different shaped nubs on them and some brands will work better than others in different Airguns. If the shape of the CO2 nub does not fit properly into the valve area then it may not pierce or it could pierce but then not allow you to tighten it all the way losing all the CO2 in the process. If the CO2 is coming form the airguns handle to CO2 Valve area then this is an indication that your problem is related to the area where the CO2 enters the airgun.

There is a seal where the CO2 cartridge buts up to the valve, this seal can be damaged or even deformed from usage or even leaving your CO2 in the gun for too long. The outside CO2 Valve seal can also take the shape of a specific CO2 nub so when you use a different brand CO2 the seal may not properly make concat with the new CO2 type you are using, again causing leaking or even the total loss of all your CO2. Watch my YouTube video on “How to Fix Leaking CO2 in an Airgun”.

CO2 Valve Related Problems:

Again, make sure that Outside CO2 Valve Seal is in good condition and any leaking is not being caused by this problem, if you have checked the Out Side Seal and everything is OK with it then perhaps there is a problem with the CO2 valve?

One indication that your CO2 Valve might be the culprit is the total loss of all your CO2 when you try to insert and tighten a new CO2 Cartridge. Usually all the CO2 will exit the barrel, not the handle or valve area. What may be happening is the valve is stuck open or the internal seal is broken or deformed. If this is the case you will have to remove the valve and have a look inside, this is a lot easier on CO2 airguns that have the CO2 valve in the magazine, if the CO2 valve is in the actual Airguns then a lot more disassembly may be required and I would recommend an Airgun technician take care of this for you.

If the gavel is in the magazine then you will have to unscrew it, you may require a special tool for this? Once the valve is out of the magazine  take a look inside and examine the internal seal, also look for any bits of metal shavings as they can disrupt the action of the valve causing leaking. Give the inside of the valve a good clean and then lubricate it with some silence spray. hopefully that fixes your problem!

BB’s getting Stuck in the Blowback Gas Tube:

I have actually made a dedicated video for this problem so I will put a link to it in the description of this video. The main reason people may have this problem is because we all like to rack that slide on our full blowback Airguns, but if you have a fully loaded magazine then each time you reach that slide without shooting the gun, you are inadvertently trying to load another BB into the breach area, the breach is only designed to hold one BB at a time so after a few racks of the slide the newly loaded have no place to go but into the Gas Tube where they can get stuck and cause having to the operation of your Full Blowback CO2 Airgun.

BB’s Rolling Out of the Barrel of Your CO2 Airgun:

This is not actually a fault of the gun but happens because of the way the gun is designed. This situation can happen with certain CO2 Airguns when the gun user pulls the trigger really slowly while the gun is point slightly in a downward position. What is actually happening is the first part of the trigger is made to draw a BB from the magazine into the breach of the gun. If the barrel of the gun does not have a rubber hop-up stopper in it then the BB is free to roll down the barrel and out of the gun. How do you fix this problem? Be more committed to your trigger pull and or shoot at a target that is not so low. Perhaps place your targets slightly higher than the gun so the barrel is not pointing down, especially if you like to take your time with the trigger :)

A Little Maintenance Can Go a Long Way!

Sometimes a good cleans is all you need to do to get things working as they should, again I have already made video Tutorial Showing “How to Clean Airguns and Blank Guns”.

What about stuff like My Airgun is jammed or my trigger is stuck or some random part fell out of my gun?

There is only so much I can cover in this video, most other problems are going to get a bit more complicated to fix and I suggest if your Airgun is not working and the suggestions I have made in this video do not solve your problem, then consider taking your gun into a gun tech.

First off I want to say it’s hard to trouble shoot technical or mechanical problems over the internet regardless of if ithas to do with guns, cars, computers or pretty much anything where unless you are there in person it’s really hard to figure out the problem.

But I will attempt to address some of the more common issues why a blank gun may not be functioning properly.

Why is my Semi Auto Blank Gun Not Cycling or Ejecting Shells?

One very common reason a blank gun may not be cycling the shells properly is because the owner has removed the barrel restrictor plug. People usually do this to make the barrel opening look more realistic but the barrel restrictor is a necessary component to increase the back pressure allowing the slide to cycle fully to the rear position so it can eject and pickup a new shell.

The blanks you are using may not have enough gun powder in them. Some blank guns require banks with more gun powder than others, again this additional internal pressure forces the slide all the way back, if the blank does not have enough gun powder in it then only a partial slide motion happens and so the discharged shell may not eject properly, in this case the user would have to clear the blank gun manually so another shell can then be picked up and loaded into the breach.

If your blank guns is dirty or not lubricated then it may act sluggish again restricting the full movement of the slide which will effect correct operation. Make sure to thoroughly clean and lubricate your blank gun, that may be a quick fix for you!

You may have a faulty extractor? The extractor is like a hook that grabs the discharged shell while the slide is in the reward position pulling or extracting the shell out of the breach. If the extractor is worn or broken then the empty shell will not be ejected from the breach so when a new shell is picked up from the magazine it has nowhere to go and usually you will get a jam-up in the ejection port area.

One final situation that can cause your blank gun to not cycle properly is to strong of a slide spring, some blank guns out of the box just come with a really heavy slide spring, so much so that even blanks with lots of gunpowder in them are still not strong enough to make the slide operate full motion. Your only option here would be to replace the heavy slide spring with a lighter one.

Why Are My Blanks Not Firing?

This is a situation where you pull the trigger and nothing happens. Lets get the obvious causes right out of the way here… Did you put blanks in your gun and are they new blanks? Did you chamber the first round in your semi auto pistol?

So now that that’s out of the way let’s look at some other reasons why your blank gun may not be firing a blank. Perhaps the firing pin is broken? Most blank guns are not made out of carbon steel and even the firing pins can be lesser quality than what you would find in a real gun so blank guns are more prone to breaking than real guns. I have seen broken firing pins in blank guns first hand so make sure to check the firing pin and that it is fully operational.

Try changing up your blanks to another brand? Again blank gun ammunition is not made to the same higher standards that real firearm ammo is made and some primers may require a little more pressure than your gun is providing. Even with real guns an ammo change may help the gun operate better.

Why is the Trigger or Hammer Not Operating Properly?

I have come across blank guns where there are mechanical problems in the trigger and hammer areas, you may be able to address this yourself but I would recommend taking your blank gun to a gunsmith since you will have to take the gun pretty much full apart to fix a problem in the trigger and hammer areas.

Of course make sure your gun is clean and lubricated, this can help a lot with the mechanical areas of your blank gun.

One problem I saw with a few EKOL Special 99’s was specifically with the single action potion of the trigger, when I would pull the hammer back it would not lock back and the hammer would often slip and fire randomly, this is rather dangerous. When I took the gun apart I found that the table top or step that the trigger was supposed to catch on was worn down on the edge so it would simply slip off. I was able to fix this by filing a new edge on the step area. Again this can happen because blank guns are not made out of as high quality metal materials as real guns.

Why does the Flame Come out the Top of My Blank Gun and Not the Front?

If you find that the flame or discharge comes out of the top of your blank gun and not the barrel, this usually does not mean anything is wrong with your blank gun. All it means is you own a top venting blank gun and not a front firing blank gun. In some countries front firing blank guns are not allowed but front venting blank guns are. The same may also be reversed in some countries, for instance here in Canada we can only import front firing blank guns with flare adaptors since our blank guns are imported under the assumption that they are to be used as signaling or flare devices.

Can I Convert my Top Venting Blank Gun into a Front Venting Blank Gun?

I really don't recommend altering a blank gun in any way as it may be a violation of your local laws and it could cause the blank gun to malfunction in a very bad way causing serious injury or even death!

In theory I suppose it may be possible to convert your Top Venting Blank Gun into a Front Venting Blank Gun but again you would need to allow for just the right amount of back pressure so a wide open barrel would not work unless it was a revolver. You can not simply remove the red plug and bingo you have a front firing blank gun because in most cases the barrel will be completely plugged in the frontal region. Not only would you need to drill out the plugged portion of the barrel but you would also have to somehow fill in the top venting area and again makes sure to allow for just enough back pressure to cycle the slide back and forth.

Hopefully this has helped some of you with blank gun issues. If you’re looking for a blank gun make sure to come down to www.ReplicaAirguns.ca and www.ReplicaAirguns.us and have a look in our blank gun area of our online stores.

Power Sources Covered in this review: CO2 - Green Gas / Propane - Spring - AEG / AEP (Automatic Electric Gun - Airsoft Electric Pistol)

Pro’s:

• CO2 Airsoft Guns allow for fast repeat shooting, great for action shooters, generally CO2 Airsoft Guns will have a little more power then Green Gas Airsoft Guns. There is no need to pump or cock your CO2 powered Airsoft gun in-between shots and a CO2 power source can allow for a very realistic action of the gun you are shooting. 

• Green Gas (Propane) Airsoft Guns operate much the same as CO2 Airsoft guns so they all make for great action shooters and the Green Gas powers the mechanical operation allowing for very realistic operation. Green Gas (Propane) Airsoft Guns can cost a little bit less to operate that a CO2 Airsoft Gun especially if you plan to use Propane as it can be cheaper to buy than the smaller 12 gram CO2 Cartridges.

• Spring Airsoft Guns are generally fairly basic and low cost so they are the usually the most affordable Airsoft guns to buy. There is no need to buy CO2 or Green Gas or even a Battery and Charger Setup so the cost to shoot Spring Airsoft Guns is only going to be subject to the Airsoft BB’s you plan on buying.

• AEG (Automatic Electric Guns) have the most consistent power as they use a spring internally that the electric motor draws back before each shot, the internal spring will essentially apply the same force to the Airsoft BB’s with each shot. AEG (Automatic Electric Guns) are a great option when you are wanting a Full Auto Airsoft gun since there is no cool down effect and as long as your batteries are charged and you have Airsoft BB’s in your magazine, the gun will simply keep shooting. AEG (Automatic Electric Guns) allow for the highest capacity magazines and often hold as many as 500 Airsoft BB’s in a single magazine. So if you’re looking for raw firepower an AEG or AEP Airsoft Gun is your best option. Once you have purchased your AEG (Automatic Electric Gun) and a battery and charger setup, they are fairly inexpensive to operate since no CO2 or Green Gas is required.

Con’s:

• CO2 Airsoft Guns require the additional cost to buy the CO2 cartridges as they will not function without it. CO2 Airsoft Guns have a limited power output and lose power as you shoot and use up the CO2. CO2 Airsoft Guns are effected by hot and cold temperatures and will have less power in colder temperatures and may not even work in super cold environments. CO2 Airsoft Guns will have a more conservative ammunition capacity since too high of a capacity magazine would freeze up the magazine and even the gun.  

• Again since Green Gas (Propane) Airsoft Guns work much like CO2 Airsoft Guns, they are effected by cool down and lose power when shoot quickly or as the Green Gas or Propane runs low. Green Gas does not expand as much as CO2 so it will not be as powerful and even less effective in colder temperatures. Green Gas Airsoft Guns will have a more conservative ammunition capacity since too high of a capacity magazine would freeze up.

• Spring Airsoft Guns are not the best action shooters since you need to manually operate the slide to pullback the spring prior to each shot, this does work well with Pump, Lever and Bolt Action Airsoft guns but is not the best option for pistols since most real steel pistols operate in semi auto mode.

• If you plan to use your AEG (Automatic Electric Gun) in a battle then it will require a multi battery setup which does cost a bit more upfront. AEG (Automatic Electric Guns) are know to not operate as realistically as a CO2 or Green Gas Airsoft gun since CO2 and Green Gas Guns do allow for the same realistic mechanical operation which can give very believable blowback operation, this is hard to replica with an AEG Airsoft Gun.

Power Sources Covered in this review: CO2 - Spring Piston - Variable Pump -HPA (High Pressure Air)

Pro’s:

• CO2 Airguns allow for fast repeat shooting, great for action shooters, generally CO2 Airguns will supply a medium power range. No need to pump or cock your CO2 powered weapon in-between shots and a CO2 power source can allow for a very realistic action of the gun you are shooting.

• Spring Piston Airguns are best suited of single shot situations, they can provide low to high power output depending on the spring used. Spring Piston Airguns are very low cost to operate since you only need to buy the Pellets or BB’s. Spring Piston Airguns are not greatly effected by outside temperatures.

• Variable Pump Airguns allow you to decide how much power your gun will have and can offer very high power output depending on the Airgun. Variable Pump Airguns are very low cost to operate since you only need to buy the Pellets or BB’s. Variable Pump Airguns are not greatly effected by outside temperatures. Variable Pump Airguns generally have very low recoil and vibration.

• HPA (High Pressure Air) Airguns generally do not require pumping or cocking in-between shots and some even come in semi automatic or bolt action. HPA Airguns can have very high power output and even be used on larger game using large caliber ammunition. HPA Air Rifles have lower recoil and low vibration. HPA Airguns can be charged ahead off time so they are ready for use when you need them.

Con’s:

• CO2 Airguns require the additional cost to buy the CO2 as they do not function without it. CO2 Airguns have a limited power output and lose power as you shoot and use up the CO2. CO2 Airguns are effected by hot and cold temperatures and will have less power in colder temperatures and may not even work in super cold environments.

• Spring Piston Airguns require cocking before each shot. Spring Piston Airguns can have a lot of recoil and vibration, so much so that special optics must be considered when buying an optical sight. The action of the spring recoil can effect accuracy, especially if you are not use to the vibration and recoil or have spent some time practicing using a Spring Piston Airgun.

• Variable Pump Airguns will require multiple pumps to achieved maximum power output which can take some time in-between shots. So you are going to have to work for each shot.

• HPA (High Pressure Air) Airguns require the use of a manual pump to fill their built in air tank to maximum pressure and it does take a lot of time to manual fill an HPA tank. Alternatively you can have the air tank filled at a shop or buy a pressurization system similar to a scuba tank out paintball setup, the cost of this setup can be very high but will save you the castle of manually pumping air in to your HPA Airgun. HPA Airguns are generally a little more bulky then other Airgun systems since they have to accommodate fairly large air pressure tanks.

Power:
Generally speaking a longer barrel is going to allow for more power. If you compare most CO2 pellet pistols to CO2 Pellet Rifles, you will find that the CO2 Pellet Pistol will generally shoot about 300-400 fps using a standard lead Pellet. On the other hand many CO2 Pellet Rifles can get up to as high as 600 fps which is much better speed for humanly shooting some smaller pests.

If you are talking about Springer or Variable Pump Air Pistols versus their Air Rifle counterparts, again the Air rifles will generally shoot with much more power. I have seen some none CO2 Air Pistols shoot up into the 500-600 fps range but again compered to none CO2 Air Rifles, they can even double these numbers.

Some of you may ask about Steel BB Pistols and Rifles. I personally would never really sue this type of ammunition for pest control simply because most BB Rifles have much less raw power than Pellet Rifles and steel BB’s will not be as accurate at any type of longer distance.

Stability:
When holding any rifle from the shoulder, you have three point of contact with your body spread out in a much longer distance than a two handed pistol grip. Holding steady even without a rested position is much easier using a rifle. Even when using a rested position, the rifle will more stable.

Accuracy:
A big factor in accuracy is stability but there are also other factors to consider. Barrel length its self does not make the gun more accurate, you only need a few inches of barrel length to get constant accurate results from a gun. What makes longer barreled guns more accurate is the distance between the rear and front sight. The closer the sights are together, the more margin for error there is, the longer you spread out the sights from each other, the more accurate the sighting system becomes.

Overall More Humain:
When you consider Air Rifles tend to have higher power, better accuracy and overall more consistency than shorter barreled Air Pistols. The logical choice for humanly shooting a Pest is to use the Air Rifle. The last thing you want to do is make any animal suffer, even if it has been causing a lot of havoc around your home or farm or place of business.

Here is my Field Test Shooting Video Review for the ASG CZ 75 P-07 Duty CO2 Airsoft Pistol. Make sure to checkout my previous Table Top Review for more detailed info about the ASG CZ 75 P-07 Duty Airsoft version.

My 5 shot Chronograph test resulted in a much lower than expected average velocity of around 265 fps, the ASG CZ 75 P-07 Duty CO2 Airsoft Pistol did start off in the mid350 range but then suddenly drop into the mid 200 fps range and according to ASG's rating, we should of been getting closer to 400 fps so something may have been up with this gun? My 10 shot accuracy test from 30 feet out using a semi rested position came in at around 4 inches. I am happy to say that my shots did seem to get to the target a bit faster than I was expecting with such a low fps chronograph testing. In terms of shot placement the ASG CZ 75 P-07 Duty CO2 Airsoft Pistol shot a bit high and to the left so you may have to adjust your aim point since there is no hop-up or windage adjustments on this pistol.

I was expecting a lot more power from the ASG CZ 75 P-07 Duty CO2 Airsoft Pistol since the 4.5mm Steel BB version of this same gun even with blowback operation still got an average of closer to 350 fps? I do like the lighter single action trigger the blowback version offers but the double action trigger of the non-blowback version is pretty good, not too heavy and fairly smooth. You can also expect to get at least 100 shots or more from a single 12 gram CO2 which makes this an relatively inexpensive gun overall.

Watch my Vimeo Video Field Test for the ASG CZ 75 P-07 Duty CO2 Airsoft Pistol:

Buy the ASG CZ 75 P-07 Duty Airsoft in Canada

Buy the ASG CZ 75 P-07 Duty Airsoft in the US