I have already done a pretest for the Umarex Walther P99 CO2 Blowback Airsoft Pistol while making my Table Top Review and it shot right around the 333 fps mark, but it was a colder day then. I also shot my Umarex Walther P99 DAO from a much closer 20 foot distance for the pretest and got a respectable 2 inch grouping.
On the actual Field Test Shooting day it was much warmer (tank top weather ;) and so as would be expected, this time my Umarex Walther Airsoft P99 shot a bit quicker at right around a 356 fps average, shooting 10 rounds through my Chronograph. I would expect to get even more fps on an even hotter day as it was only about 22 degrees Celsius or about 72 Fahrenheit on this test day.
Accuracy from 30 feet out was pretty close to my pretest 20 foot testing if you exclude the two flyers but again the Umarex Airsoft P99 version was shooting a bit to the left which unfortunately can not be adjusted other than changing my sight position on the target. I would think the trend to the left will only increase as we shoot further out but this gun is really best suited for close quarters shooting anyways and should have no problems right up to 50 feet shooting a man sized target..
You can expect to get around 100 shots or a good 6 full 15 shot magazines from Umarex Walther P99 CO2 Blowback Airsoft Pistol which should get you nicely through a CQB match without having to change CO2 cartridges. For being a rather low cost Airsoft gun, it did perform well enough for me on this day, keep in mind it does have a firm long pull double action only trigger so really fast shooting will take it's toll on your trigger finger ;)
Watch my Field Test Shooting Video for the Umarex Walther P99 CO2 Blowback Airsoft Pistol:
I've had the opportunity to review and shoot my Dan Wesson 4.5mm Steel BB Version so I kind of knew what to expect with the Airsoft version, much of the same but with perhaps a little bit less accurate further out shooting since the plastic BB's will tend to drift a bit more.
I already did my pretest for the ASG Dan Wesson 6 Inch Silver CO2 Airsoft Revolver while making my Table Top Review and shot right around the 400 fps mark, but it was a colder day then, I also shot my ASG Dan Wesson Airsoft Revolver from a closer up 20 feet for the pretest and got a nice tight 1.5 inch shot group.
On the actual Field Test Shooting day it was much warmer (tank top weather ;) and so as would be expected, this time my ASG Dan Wesson 6 Inch Silver CO2 Airsoft Revolver shot a bit faster at closer to a 420 fps average with 6 shots put through it. There is even room for some more fps still as it was only about 22 degrees Celsius or about 72 Fahrenheit on the test day.
Accuracy from 30 feet out was not as tight as my pretest 20 foot testing and I would imagine this will spread out even more the further back we go with the Airsoft ASG Dan Wesson, as is the case with Airsoft BB's. Airsoft BB's are just not as accurate as steel BB's especially when shooting at longer ranges. I would expect this Airsoft Dan Wesson version should still be very effective on a "man sized target" up to about 60 feet or so. Keep in mind there is no hop-up in this revolver so teh Airsoft BB's will drop much more than a gun that has hop-up.
Like the 4.5mm BB shooting version you can expect a good 100 or more shots from this Airsoft BB Shooting Dan Wesson CO2 Revolver. Having tradition revolver single and double action makes for both precise and action styled shooting. All in all a really nice Airsoft pistol from ASG.
Watch my Field Test Shooting Video for the ASG Dan Wesson 6 Inch Silver CO2 Airsoft Revolver:
Action: Semi auto, double action only with blowback.
Ammunition Type: 6mm plastic Airsoft BB's.
Ammunition Capacity: 15 round stick magazine.
FPS: 380.
Trigger Pull: The Double Action Only trigger pull on the Umarex Walther P99 CO2 Blowback Airsoft Pistol is long but not overly heavy for a double action trigger, it does have a break point mid way where it locks partway back, I presume this is the point in which a BB is loaded from the magazine into the barrel? The rest of the pull is still medium but much shorter with a distinct release point.
Accuracy: I did do a quick preliminary test before I made this table top review to get an idea of where this gun performs in terms of FPS and accuracy, I shot 5 rounds through my Chronograph on a fresh CO2 and got an average of 333FPS which was a bit lower than the claimed 380 but it was not the hottest of days. I also stepped back 20 feet and from a semi rested position I was able to get 9 shots within 2 inches of each other which was not bad for a DAO gun that I have never shot before. I did shoot a bit down and to the left with the set sights.
Build Quality: The Umarex Walther P99 is well built for its rather low price tag, it may not have all the bells and whistles but it does get the job done with good fit and finish and materials used. You will find a plastic/polymer frame but there is a lot of metal where it would normally be found on the real steel version like in the slide, magazine, trigger, slide catch, magazine release, inner barrel and many other internal parts. No real complaints here!
Realism: The Umarex Walther P99 CO2 Blowback Airsoft Pistol is pretty close in looks to a real steel Walther P99 with the exception of a missing decocker, but I'm pretty sure this is the same with the real steel DAO version? There is also the funny looking safety on the right side of the frame found on many Umarex airguns. I have to mention the red tip but again this can be removed and even when removed the barrel it is still recessed which adds to the realism. The Blowback action, Walther licensing and nice heavy weight all add up to make this Airsoft pistol look and feel the part.
Metal slide and internal parts gives it decent weight.
Rail for accessories.
Well hidden CO2 screw.
Walther licensing.
Recessed inner barrel.
White dot sights, easy to use.
Right amount of power for indoor CQB style airsoft games.
Cons:
Comes with a red tip even in Canada.
Double action only, so trigger is a bit heavier.
Kind of funny safety, not like the real gun.
Blowback was a bit sluggish.
Comments:
Overall the Umarex Walther P99 CO2 Blowback Airsoft Pistol is a very good buy, it's a decent replica of the real steel Walther P99 with blowback operation, lots of metal parts, good fit and finish, decent performance and full Walther licensing and trademarks. All at a very affordable price tag. It may lack some of the extras you will find on more expensive and more functional Airsoft pistols but the simplicity of the Umarex Walther P99 CO2 Blowback Airsoft Pistol means it will most likely be a bit more reliable with less to go wrong down the road. If you have been looking for a nice Walther styled replica in an Airsoft version this may be just be the ticket!
My Vimeo Video Review for the Umarex Walther P99 CO2 Blowback Airsoft Pistol:
Trigger Pull: The ASG Dan Wesson Airsoft Revolver has a predictable trigger with the single action being a bit lighter and more consistent, not just in feel but also in fps. Double action shooting is very usable without a lot of extra pressure required and makes for fun consecutive shooting albeit you will run our of ammo pretty quick compared to many high capacity semi auto styled airguns.
Accuracy: I shot the Dan Wesson Airsoft Revolver at a target from 20 feet away in a semi rested position, and it performed excellent, getting a 1.5 inch 6 shot grouping dead center in the bullseye! The sights are fully adjustable for elevation and windage so getting these guns centered on the bullseye if you where out a bit would be very easy. My Chrony testing for the Dan Wesson Airsoft Revolver with a six shots averaged result was 399 fps.
Build Quality: This detailed revolver is extremely well built! All the Dan Wesson Revolvers are almost all metal with just a few components made out of plastic, like the handle and CO2 screw tab. The handle feels like a cross between plastic and rubber but is basically plastic with a coated paint on it that can wear off with long term use so try and go easy on the grips. The finish on the six inch silver Dan Wesson is amazing and looks just like polished stainless steel. Very nice indeed!
Realism: The ASG Dan Wesson BB revolvers are as close as you can get to a real six shooter, ASG didn't leave out any details and has really brought us an extremely believable CO2 revolver that mimics the real steel in almost every way! Loading and ejecting actual brass shells into the cylinder makes you feel like this gun is much more then an unassuming airgun!
It's a revolver with actual brass shells giving you the feeling of a real 6 shooter!
Almost all metal design.
lots of detail in this gun, very well made, fit and finish is excellent.
Good power and good accuracy.
Fully adjustable sights.
Can mount a scope of some sort on it with the rail attached.
Right amount of power, even for some indoor CQB style airsoft games
Cons:
Plastic CO2 screw tab (but is well hidden and protected).
Grips can wear a bit with extended use.
Red tip on the US version :(
Comments:
I wasn't really a revolver person until I got my Dan Wesson's! They are really fun to shoot and yes you only get to fire off 6 shots at a time but the reloading is kind of fun and adds to the realism of shooting a revolver styled gun. The other benefit to taking breaks every 6 shots to reload is the time it allows your CO2 and gun to warm up which increases the overall FPS and shots per CO2. I am not sure if a large six shot revolver is the way to go when in a high intensity Airsoft game but I can tell you when you're on the other end of the barrel of one of these you are probably not thinking how many shots does he have left :)
My Vimeo Video Table Top Review for this amazingly real Airsoft Revolver:
I managed to acquire another Russian made Nickel Baikal MP-654K CO2 BB Pistol, the last one that came my way was back in September of 2012 and I am really surprised I got my hands on another one to be honest so if you missed out on the last one, now is your chance!
This 2004 Baikal Makarov Nickel MP-654K BB Pistol is in brand new condition and comes with the original box, manual, tools and o-rings. I have test fired it and it works great and holds CO2 with no leaks.
If you want the background info I encourage you to checkout the review videos I have already made for my own person exact version of this gun right down to the same production year:
To get in on the bidding, simply Email Me Here with your highest bid by no later than May 31st 2013 by midnight. At the conclusion of this Silent Auction I will notify the winner and they will have 24 hours to make payment before I move onto the next highest bidder.
This Rare Airgun Silent Auction is open to both my Canada and US customers, Canadian Customers will pay an additional $17.99 for Shipping/Handling plus their local provincial sales Tax. US Customers will pay $29.99 International Canada to US Shipping & Handling but will not pay any sales tax. Good luck to everyone!
Enjoy my YouTube Video showing off this gorgeous Airgun and below that are some additional photos:
I will be doing proper Table Top and Field Test Videos for each of these Airsoft guns as soon as I can get to them all, starting with the Umarex Gas Blowback H&K MP7 A1 Airsoft PDW so stay posted for these upcoming video reviews...
After many many requests to show how the Umarex Walther PPK CO2 Tab Modification is done I have relented to public demand. I don't actually cut my tab in this PPK CO2 Tab Modification Video but I do go step-by-step in detail and compare my modified Umarex PPK to my unmodified Umarex PPK. It is really very basic on how this is done and only a hack say and perhaps a file are all that is required to make the modifications to the PPK CO2 tab in order to make it flush with the bottom of the handle area.
Your best bet is to simply watch my YouTube Video located below and follow the steps there but here it is in text form:
Place an empty (already pierced) CO2 into your Umarex Walther PPK and tighten the unmodified CO2 tab until fully tightened, just like you would tighten a fresh CO2.
Take note at how many threads are exposed between the bottom of the handle and the top of the plastic CO2 tab, there should be about 2-4 threads exposed.
Unscrew the CO2 tab all the way, place the PPK BB Pistol so it is secure (in a vice of some sort) and use a hacksaw or dremel to shorten the CO2 screw just above the plastic tab at the thread location you previously noted. Be conservative as you can always cut or file the screw a bit shorter if your first cut was not short enough.
Now use the same hacksaw or dremel to cut a notch in the exposed cut area of the CO2 screw so that you can use a slot screwdriver to tighten the CO2 screw.
That's it - Enjoy your modified Umarex Walther PPK CO2 BB Pistol!
Watch my Vimeo Video of the Umarex Walther PPK CO2 Tab Modification Tutorial:
Every once in a while something goes wrong and your favorite BB shooter stops working as it should :( One of the most common problems I see with many of the full blowback BB and Airsoft pistols are BB's getting stuck in the gas tube. This is because this style of gun loads a BB into the breach area of the barrel every time you rack the slide forward. Of course this is only when there are BB's in the magazine.
The semi auto style of these guns is similar to that of a real gun, the blowback operates the slide which in turn moves back and then forward and loads a BB into the chamber. With a real gun, if you where to rack the slide manually again without shooting it, the chambered round would be ejected by the extractor but with a BB gun there is no extractor because there is no spent shell to eject. So multiple BB's can be loaded into the chamber area of the barrel overloading it and if the BB's have nowhere to go they just jam up and often go back into the gas tube which can cause all kinds of problems...
In this Cybergun KWC Tanfoglio Witness 1911 Stuck BB Removal Tutorial Video, I show you how to remove a BB or even multiple BB's from the gas tube area which in short requires; the removal of the slide and guid rod and spring so that you can push the gas tube forward and shake the BB out of the front of the gas tube.
Watch my Vimeo Video on how to remove a stuck BB from the Gas Tube on my Tanfoglio Witness 1911.
Materials: Metal and plastic (polymer) construction.
Weight: 1 pound 10.5 ounces (752 grams).
Barrel: 3.3 inches, metal rifled.
Propulsion: CO2 x 1.
Action: Semi auto, single and double action.
Ammunition Type: .177 caliber pellets
Ammunition Capacity: 8 shot rotary magazine.
FPS: 360.
Trigger Pull: The trigger pull on the Umarex Walther CP99 is in the mid range for it's double action trigger pull with most of the effort at the beginning and middle stages as it cocks the hammer and indexes the rotary magazine, it does have a predictable release point making it easy to put pellets on target. By racking the rear slide you can put the CP99 in single action mode which makes the trigger pull much lighter and great for very accurate shots.
Accuracy: I shot this air pistol at a target from 20 feet away in a free semi rested position and it performed well getting a nice tight one inch eight shot grouping just to the left on the target. The sights can be adjusted for windage if your aim is off to one side or the other. With my preliminary Chrony Chronograph testing using 6.9 grain RWS lead pellets I got pretty close to the factory claim of 360fps with an average of right around 346 fps.
Build Quality: The Umarex Walther CP99 is a metal and polymer air gun with a good deal of metal components on the inside giving the Walther CPSport a decent overall weight and heft. It's worth mentioning that the Walther CP99 has a full size drop out magazine for holding the CO2 cartridge that gives the air gun some additional weight and functionality. The German made fit and finish is very good on the CP99 and the plastic quality is also very good.
Realism: The Umarex Walther CP99 is licensed by Walther and is based around the Walther P99. The frame is very similar to the P99 but the slide is not as accurate in terms of the real steel but you can definitely tell the Pellet shooting CP99 is a copy of a Walther P99. One of the biggest shortcomings is the safety, the real P99 does not have a safety but Umarex decided to put a rather large safety on the right hand slide area. I do however like the working de-cocker, slide catch for loading magazines and full size drop out magazine which give the Umarex CP99 a more realistic look and feel.
Slide catch and de-cocker are realistic and functional.
Rifled barrel.
Sights are adjustable for windage.
Slide catch and magazine release are fully functional.
Nice full size drop out CO2 magazine.
Good combination of power, accuracy and CO2 efficiency (I got about 100 shots from a CO2)!
Rail for accessories.
Walther licensing.
German Quality.
Cons:
Up in the higher price range.
Double action can have some stickier shots.
Kind of funny safety, not true to the real steel Walther P99.
No recessed barrel
Comments:
The Umarex Walther CP99 Pellet CO2 Air Pistol is a nice step up from the Walther CPSport I reviewed earlier. The CP99 is a much more accurate looking replica of the P99 and it also has more metal parts and a single and double action trigger. These added features do come with an additional $100 price tag but in my opinion are worth it. If you're a fan of the Walther line of pistols than you should probably take a look at the Umarex Walther CP99 as it would make a great addition to your airgun collection.
Ammunition Capacity: 13 round full size metal magazine -18 round metal stick magazine.
FPS: 428 - 380.
Trigger Pull: There is a lot of difference between the trigger on both of these guns, first off the Umarex Makarov has both a single and double action trigger/hammer while the KWC Makarov has a double action only trigger/hammer. Comparing the double action of both guns the definite advantage goes to the 4.5mm Steel BB shooting Umarex Makarov as it is shorter and lighter, the KWC Airsoft Makarov does not have a bad trigger but it is much longer and a bit heavier, but still very usable. The single action trigger on the Umarex Makarov is not really any lighter than when shooting in double action, it is however much shorter with a medium take-up and predictable release.
Accuracy: Both Airsoft and BB Makarov's performed very well in their shooting tests for me, they bot shot fairly well centered with the KWC Makarov getting all five shots in the black bullseye and the Umarex Makarov having a tighter group but just off to one side. This was good news since both guns do not have adjustable sights! They also scored very well in the velocity department shooting over their advertised claimed feet per second rating. The Umarex BB version shot a very respectable 390 fps while the KWC Airsoft pistol shot a very surprising 480 fps well over the claimed factory 430 fps. Both guns also shot very accurately out to ranges of 50 feet or so. From a single CO2 I was able to get 162 shots from the Umarex Makarov and 112 shots from the KWC Makarov before I noticed a significant power drop.
Build Quality: Neither one these Makarov replicas is going to win a prize for build quality, some shortcuts have been made to keep the price down on each model, but they are both built with mostly metal parts and they both performed perfectly for me during my testing. The Umarex 4.5mm Steel BB Makarov did have more moving parts while the KWC did weigh in a bit heavier, both guns had reasonable fit and finish to them.
Realism: In terms of being good Makarov replicas the pair for sure look the part, size and overall weight are very true to the original real Steel Makarov PM with the Umarex Makarov having a working slide, Makarov licensing and the ability to be field stripped. The KWC Makarov had a nicer recessed barrel and full size drop out metal magazine. I was not a big fan of the KWC screws on the right side slide or the Umarex exposed CO2 tab.
KWC may shoot a bit too hot for CQB Airsoft games.
Both guns do not have adjustable sights.
Comments:
To be honest when I got the KWC Airsoft BB shooting Makarov, I was not all that awe struck, the lack of a working slide, DOA trigger and screw holes in the slide put me off just a bit. This Airsoft pistol did warm up to me a lot once I shot it, I was surprised by the very high fps and how accurate it was for such a low cost Airsoft pistol. I can really see this gun being used as a backup or sidearm in an out doors style Airsoft game where you may need to shoot targets out at range where other lower powered pistols just would not be able to get out to. The Umarex Makarov has always had a place in my heart, it is just a really good little CO2 BB pistol for the price with mostly all metal parts, a working slide, single and double action trigger and very good overall performance. In my books you can not go wrong choosing either of these Makarov replicas so choose wisely!
My Vimeo Video Table Top Comparison Review for these Makarov Air Replicas:
We have been taking preorders on many of our ASG Airguns and Airsoft guns for our Canada Replica Airguns Store, we where expecting them to be back in stock right around the end of the month. The good news is we got them a bit early so we are now filling back orders and most of our ASG inventory is now showing as in stock and ready to ship!
So if you've been waiting for an ASG gun, make sure to grab yours now before we run out again...
This is not meant to be a full review of either the BB or Airsoft version of the Cybergun - KWC CO2 Blowback Mini UZI's but I do talk about specifications, show you around both guns, and put them both through a full Field Test so I guess in a way, perhaps it can be considered to be a full review ;)
I will list the specifications here for you but I am not going to get into details like Trigger Pull, Build Quality, Accuracy and Realism. You can check out my other video reviews for more information on the Mini UZI:
As I said you can check out all my other videos for info on these very accurate Mini UZI Replicas, I mainly want to go over some of the main differences and similarities for both the BB and Airsoft versions.
In terms of build quality they are made almost exactly the same and weigh in at a hefty near 5 pounds, the only differences are the inner barrel and magazines to accommodate the different sized ammo. The BB version has a 25 round single stack magazine that does not have a follower to stop the bolt from continuing to operate even after the magazine is empty. While the 6mm Airsoft version has a double stack magazine that holds 38 rounds and does have a follower to stop the bolt which can save you some unintentional wasted CO2.
The Airsoft Mini UZI version is distributed by KWC while the 4.5mm BB version is distributed by Cybergun, you will find the UZI and IWI licensing on the Cybergun 4.5mm BB version but not on the KWC 6mm Airsoft version.
Out of the box the KWC Airsoft Mini UZI is ready to go in both semi auto and full auto while the 4.5mm steel BB version will only shoot in semi auto mode, it can however be easily modded to shoot in full auto.
Both guns come in cardboard boxes with manuals, some BB's and an Allen key to tighten the CO2. The KWC Airsoft Mini UZI also comes with a handy speed loader.
There is a slight fps velocity difference between the two with the KWC Airsoft 6mm plastic rounds traveling at around 400 fps (with .20 gram BB's) and the 4.5mm Steel BB's traveling at right around 350 fps. In the field test portion I test both guns out on some water filled cans to see how each ammo type performs in terms of penetration.
Your best bet is to watch both my Table Top and Field Test Comparison Video Reviews and see for yourself how they compare!
For the most part, this video is to test out some cameras and using them all together in a multi-camera scenario. I wanted to see how many camera angles I could shoot at one time and see how they would all work together when editing the video.
Cameras used:
My new Pivothead Recon Camera Glasses.
Sony HDR-AS15 Action Cam.
Drift HD170 Point of View Camera.
Nikon 1 with 10mm fixed lens.
Casio TRYX.
*All cameras where shooting in 1080p for this video.
I hope to use camera setups like this in the future, maybe not all at once but at least a couple at a time to give you some viewing options.
I picked out my WE SCAR GBB Airsoft Rifle for this test as it had a lot of mounting points and the Gas Blow Back makes for some great video action. Unfortunately My WE SCAR was not working at 100% but I still think I was able to pull off this test video either way.
Watch my Multi-Camera-Angle Test Video shooting the WE SCAR GBB AIrsoft Rifle:
Here is my official Field Test Shooting Video Review for my Daisy Winchester Model 11 CO2 Blowback BB Pistol. Make sure to checkout my previous Table Top Review for more details on the Winchester Model 11 1911 CO2 4.5mm BB version where I also did a pre-test showing similar results.
My 5 shot Chronograph test resulted in a bit lower than previously tested 339 average fps while my accuracy test shot from 20 feet out in a semi rested position got six shots right in the 1.5 inch bullseye with 4 shots coming out a bit, 2 of which spread the group out to about a 3 inch grouping in total. So in terms of shot placement you could say the Daisy Winchester 1911 4.5mm BB Pistol shot very well centered. Agin this time around I got 6 full magazines but had to manually clock teh hammer back on some of the last magazines end shots, power did seem OK even when manually cocking the hammer.
Overall, the Daisy Model 11 4.5mm BB Pistol is nice pretty much all metal low-cost CO2 Blowback BB pistol with good overall performance. This one looks the part of a 1911 even though it may not function 100%. If your OK with close and want to save a few bucks, then teh Daisy Winchester Model 11 may be for you, if you don't mind spending a bit more to get a BB gun as close to a real 1911 A1 as possible than take a look at the KWC/Cybergun Tanfoglio Model 1911 full blowback BB Pistol and Airsoft Pistol versions.
Here is my official Field Test Shooting Video Review for my KWC Sigma SW40F CO2 Blowback BB Pistol. Make sure to checkout my previous Table Top Review for more details on the KWC SW40F 4.5mm BB version where I also did a pre-test showing some similar results.
My 5 shot Chronograph test resulted in a somewhat expected 285 average fps while my accuracy test shot from 20 feet out in a semi rested position received a slightly wider 3 inch group this time but with most shots being within 1 inch of each other. In terms of shot placement the KWC SW40F 4.5mm BB Pistol shot very well centered but just slightly low. I also only got 2 full magazines this time around so don't expect a lot of shots per CO2 with this 4.5mm BB pistol.
Overall, the KWC SW40F 4.5mm BB Pistol is a really fun gun to shoot with a very crisp heavy slide that gives a nice firm blowback snap to it. It is one of the nicer sounding slides with a less tinny sound than most. The fps and shots per CO2 is a bit low but other than that performance is very good, you will have no problem nocking down cans and acquiring other miscellaneous targets.
ALL GUNS ARE NOW SOLD - THANKS FOR THE AWESOME RESPONSE!
This is a first for me but I guess you could say I have to make room for some more guns ;) I have some duplicate guns and a couple I juts don't have a need for anymore so instead of having them sit around collecting dust, I thought I would offer them up for sale and get them in the hands of someone who can really appreciate and get some use out of them...
Here is a list of the items up for sale:
Baikal IZH-61 .177 Caliber Spring Piston Pellet Rifle: $115
Baikal MP-655K Pellet/BB CO2 Pistol (missing pellet magazine): $125
Umarex CP99 Compact CO2 BB Blowback Pistol: $50
Swiss Arms Sig Sauer GSR 1911 CO2 BB Pistol: $30
ASG CZ 75 P-07 DUTY Dual Tone CO2 BB Blowback Pistol: $125
Umarex Beretta M92FS .177 Caliber CO2 Pellet Pistol - Nickel with Wood Grips: $200
(2x) AK47 BB Gun Magazines: $50 Each
Crosman 2240 .22 Caliber CO2 Pellet Pistol (14 inch barrel, RJMachine Breach/Brass Bolt, Wood Grip, NcSTAR 6x32 Scope): $225
Shipping/Handling is $15 Canadian and $25 to the US and you must be 18 or over to buy. You will need to email me at mike@replicaairguns.com to let me know what gun/guns you want to buy - first come first serve, I will send a PayPal request to the person with the first offer to buy and give them 24 hours to pay or I move on to the next buyer.
You can watch my YouTube Video to get a good look at each pre-owned item up for sale:
The KWC/Cybergun Model 1911 Blowback BB Pistols and Airsoft Pistols are very popular and so I tend to get lots of questions about them like: Are they the same quality? What version shoots the best? How do I remove the white warning lettering? Can I get one in an Airsoft version? Can I add a laser or tactical light? Can I change the grips...
So in this YouTube video I compare all four existing KWC and Cybergun model 1911's showing you the Cybergun Tanfoglio Witness 1911 in 4.5mm Steel BB, the KWC Model 1911 and Model 1911 A1 Tac also in 4.5mm Steel BB and lastly the KWC Model 1911 in 6mm Airsoft plastic BB.
Watch my Vimeo Video of these four KWC and Cybergun Model 1911 4.5mm Steel BB and Airsoft CO2 Blowback Pistols:
We just added some Baikal producst to the Canada Replica Airguns Store, we even have the already full auto modded Baikal Drozd Blackbird ready to shoot 1200 rounds per minut.
Trigger Pull: The trigger pull on the Daisy Winchester Model 11 is very nice, just about the perfect pull weight, not too heavy or too light, it has next to no take-up at all and a nice predictable release point. As is traditional with a 1911 styled pistol, the trigger is single action only so you will need to either pull the hammer back or rack the slide for the first shot, with subsequent shots you will not have to do this as the blowback action cocks the hammer for single action shooting. If your CO2 is very low, the blowback may not be adequate enough to cock the hammer so you can do this manually to get a few extra shots out of the Daisy Model 11.
Accuracy: When I shot the Winchester Model 11 from 20 feet out in a semi rested position, I was able to get some decent results. I placed 10 rounds within about a 2 group and the shot placement was very well centered, just a slight bit to the left. I did get a couple of stragglers that spread the group out just a bit larger but not too much. I did also get right around 350-360 fps on my chronograph on this not so warm day. We will have to see what my dedicated field test results yield for this BB pistol.
Build Quality: The Daisy Model 11 (1911) is made in Japan and has a nice overall finish to it. Other than the plastic magazine and grips it is an all metal gun so the materials used are good. The slide does have a bit of wiggle play in it but so do many blowback air pistols, perhaps to reduce some friction as the slide springs on these guns are not overly heavy. The paint used seems to be holding up very well and looks good, I did notice a molding seem that runs down the underside of the slide and along the trigger guard.
Realism: The Daisy Winchester Model 11 is a replica of the real steel 1911 A1 style 45 auto. It does have the Winchester licensing on it but I am not sure if there is an exact Winchester 1911 this gun is made to replicate. For the most part it looks and functions very similar to a real 1911 with a few exceptions like the lack of a working grip safety, a rather strange two stage safety and also the stick styled smaller magazine. This blowback air pistol can not be field striped conventionally either. I do like the true single action trigger and open ejection port.
Lots of metal in this airgun and good weight to it.
Good overall looking replica of a real 1911.
Reasonably decent blowback feel.
Mid range fps and shots per CO2.
Very nice true single action trigger.
Shots where well centered and got decent accuracy.
Markings and instructions on gun are color matched.
Solid CO2 tightening system, seems to work well once you get the hang of it.
Not bad at all for the lower price point.
Like the open ejection port.
Made in Japan.
Cons:
Kind of funny safety setup, it is redundant?
Has a plastic magazine, would have been nice in metal.
Back strap safety does not actually work but it does move.
Says "clip" instead of "magazine" on gun.
Comments:
I know some people have been hating on this gun for a couple of reason so let's get them out of the way... Yes it has a weird safety setup and I can not tell you why Daisy did this, perhaps they wanted it to be "more safe"? As a 1911 trainer you will have to adapt how you take this gun off of safety over a traditional 1911 setup. The magazine is plastic, not a biggie, if it breaks on you get another one. It's not full blowback like the Cybergun/KWC Tanfoglio 1911, this is true but you do get higher fps and more shots per CO2 out of it because of this. And yes Daisy uses the word "Clip"on the gun instead of the correct term "Magazine". Honestly, the Daisy WInchester Model 11 is a nice overall BB gun and the price point is pretty low for what you get. It looks really good overall and shoots nicely with enough blowback to give you some recoil feel and allow for true single action shooting. You also get decent fps and a good amount of shots from a single CO2 cartridge so stop complaining and just enjoy this gun for what it is!
My Vimeo Table Top Review of the Daisy Winchester Model 11 Blowback CO2 BB Pistol:
