When I say Airguns, I am referring to pretty much all BB, Airsoft, Pellet, Paintball and even Blank guns for most of the topics listed here.
Do’s:
Treat your Airgun just like you would a real gun. If something goes wrong, perhaps the outcome will not be as severe but do you really want to take a trip down to your local emergency ward to get a BB or Pellet removed?
Always assume your airgun is loaded, for some reason it always seems those empty guns are the ones that do the most damage.
Be discrete, If it looks like a gun other people will think it is a gun so don’t flash your airguns around in public. Keep it in a case when transporting and shoot it in an area that will not alarm other people.
Always wear eye protection when shooting your Airgun. Do you really want to shoot your eye out? No Joke!
Be aware of your surroundings like windows, hard objects that could make your ammo bounce back at you. Make sure you are shooting your Airgun in a safe direction at all times, know your target and beyond.
Use Airguns to teach others and learn how to safely and effectively shoot a gun. Airguns can be less intimidating then a real gun (Not so loud and very little recoil) and make for great start out and transitions guns.
Use Airguns to get more inexpensive trigger time and become a more experienced shooter. Airguns cosy only pennies per round to shoot and can be shot in way more areas than a real gun can, practice makes perfect so get shooting!
Use Airguns in areas where real guns may not be allowed or safe to use. Again, Airguns can be shot in all kinds of places, in your back yard or even in a properly setup indoor home range.
Use Airguns with adequate power for safe and humane pest control where real guns may be prohibited.Airguns are quiet and less likely for the bullet to travel long ranges which makes them ideal for close range pest control in areas where real guns are too loud and to powerful.
Don’ts:
Do not assume because it is an airgun it is not dangerous or simply a toy. Many Deaths have been caused by Airguns along with a lot of pain and suffering so treat your Airgun with respect. It is not a toy or you would find them in the toy department at your local store along with yo-yos and stuffed animals.
Do not point or shoot at people unless of course you are using an Airsoft gun in an Airsoft field or facility. Yes Airsoft guns are meant to shoot at each other (with appropriate attire like eye protection and full body clothing), but steel BB and Pellet can cause serious injury especially at close range and on direct skin contact.
Do not leave your Airgun loaded, you never know who is going to come across it and accidentally discharge it. Remember, a loaded gun is a dangerous gun in the wrong hands. You may know better than to assume the gun is undulated but children and even adults without any gun training will most definitely handle the airgun without consideration of the danger it poses.
Do not use an Airgun for self protection. See my related video. Simply put, Airguns are not practical for self defense because they rarely have enough Stopping Power. The ones that do have enough power need to be pre-charged and in most cases are only single shot meaning if you miss or don’t get the job done no the first shot then you are done.
Do not use an underpowered Airgun for pest control. See related video. Using a low powered BB pistol for pest control is cruel, you will only injure the animal making it suffer unnecessarily. Use a high powered pellet rifle to get the job done.
Do not take your gun apart, in most cases this will void the warranty and the reality is that airguns rarely need to be cleaned since no dirty gun powder is used. lead pellet rifles may require occasional barrel cleaning to keep the rifled barrel free of debris.
Do not over oil your Airgun, a little goes a long way and too much oil will just attracted dirt, use the right airgun oil and just enough to keep part functioning smoothly.
Do not over pump an Airgun. Over pumping an Airgun can cause damage to valves and seals and in a worse case situation a rupture the air pressure reservoir or even cause the airgun to explode!
Can I use Airsoft BB's in my BB Pistol? I would have to say this is by far the number one question I get asked in the comments section of my Vimeo videos. I have made several videos where this question gets addressed within the video but so far to date I have not made a stand alone video just covering Airsoft BB use in BB Guns.
So here it is, and now I have a video I can link to this so very common question, if you where wondering about this yourself than please watch my YouTube Video on this topic as it goes into a fair amount of detail about it.
The short answer to this question is no, you can not use 6mm Airsoft BB's in a 4.5mm Steel BB Pistol or Rifle. For the simple reason that 6mm is larger than 4.5mm and so the physical diameter of a6mm Plastic Airsoft BB is just to large to fit inside of a 4.5mm Steel BB magazine or barrel.
People have commented about using a 4.5mm plastic Airsoft BB in a 4.5mm BB gun and yes this could in theory be an option but I discuss why I feel this is not a good idea based on size and mass.
In this video I feature my top five favorite BB pistols for early 2016. That said there are lots of other BB pistols I truly love and enjoy but I had to pick 5 so these are them! You may notice that many of them are blowback, I do like the blowback guns after all and this is my top 5 pick so naturally many of them will have blowback action.
Here is a list of my top 5 guns featured in this video not necessarily in order of choice:
With the popularity of the KWC - Cybergun 1911 Blowback CO2 Pistols and how super realistic they are in so many ways, it is no surprise that people often ask me if they can replace the original grips with grips made for a real 1911.
The short answer is yes you can! You will have to be prepared to remove just a little bit of material from the backside of both grips near the bottom of the handle where there is an area that has been flared out to accommodate the CO2. Not really a big deal, you can use a Dremel for the quick and easy approach or even some sand paper if you don't mind taking a little more time.
I'm getting close to uploading 600 videos now over on the Replica Airguns Vimeo channel, so there are bound to be a lot of similar questions and popular discussions. In this Replica Airguns Vimeo Video I address what I feel are my Top 10 Most Common Airgun Questions and Discussions.
Ammunition Capacity: 17 round full size metal magazine.
FPS: 380 using .20 gram BB's.
This is a Mini Review for the KWC/Cybergun Colt M1911 A1 CO2 Blowback Airsoft Pistol. I have already reviewed other KWC version of this all metal realistic CO2 blowback pistol in both 6mm Airsoft and 4.5mm Steel BB and in a variety of different finishes so if you are interested in a more detailed write up for the Cybergun Colt M1911 A1, you can check out the below links where I have reviewed many variations of virtually the same blowback CO2 airgun made by KWC.
Action: Semi auto non-blowback, double action only.
Ammunition Type: Steel BBs 4.5mm.
Ammunition Capacity: 21 rounds
FPS: 394 fps/ 120 m/s.
Trigger Pull: The trigger pull on the KWC Metal Slide CQBP M45 A1 Non-Blowback CO2 BB Pistol was about medium to hard but I have definitely experienced heavier trigger pulls on some guns. It is nice that the trigger is in the style of a 1911 and not your typical lever styled trigger like you will find on some 1911 wannabe's. I imagine if the CQBP M45 A1 has a lever style trigger it would have more leverage and be a bit lighter.
Accuracy: I have not shot the KWC Metal Slide CQBP M45 A1 Non-Blowback CO2 BB Pistol but expect it to perform similar to the Cybergun Sig Sauer GSR Sigarms I reviewed a while back since both guns have similar internals so for now until I do my dedicated Field Test review you can read my Cybergun Sig Sauer GSR Sigarms Review: "Accuracy was decent but not outstanding, I got around a 2.5 inch grouping from a 20 foot away free standing position, shooting just to the left and high on the target. I did find that I was able to zone in a bit better with the Cybergun GSR as I got used to the trigger. I also put the Cybergun Sig Sauer GSR through my Chrony Chronograph and got very close the manufacturers 397 claimed feet per second, actually starting off well above it and settling down to around the 370 FPS mark. My 8 shot average on a new CO2 was actually 422 FPS."
Build Quality: You will find a pretty nice balance of metal and plastic on the KWC Metal Slide CQBP M45 A1 Non-Blowback CO2 BB Pistol. The metal slide, magazine barrel and some literals give it a really decent weight in the hand and the fit and fish feel good overall. The trigger and hammer are not the best aspects of the gun in terms of quality as they are both plastic and both kind of made more for show and less for function.
Realism: The KWC Metal Slide CQBP M45 A1 Non-Blowback CO2 BB Pistol looks and feel the part of a M45 1911 A1 including a full size drop out metal magazine, working magazine release and safety. The slide catch release is none functioning and so is the hammer which does not cock back for single action shooting. It would have been nice to have a single action trigger and a working slide to finish off this pistol but it is meant to be more of an entry level pistol at the end of the day.
Should have good FPS and lots of shots per CO2 based on my 4.5mm BB version testing!
Rail for mounting accessories.
Nice white dot sights.
Recessed barrel give it a more realistic look.
True 1911 style looking trigger even though it is double action only.
True 1911 working safety.
Cons:
No blowback - slide does not move either.
Hammer moves but does not cock so no single action shooting.
Non adjustable rear sight.
Trigger action is bit heavy and long so it’s not going to be the fastest action shooter.
Comments:
If you're looking for a lower cost well made 1911 in that classic A1 style but with a little bit of updating like having a Picatinny rail and tactical sights then the KWC Metal Slide CQBP M45 A1 Non-Blowback CO2 BB Pistolmay just be right for you. So it doesn't have blowback or a working slide, on the other hand it has lots of metal on it giving it good weight and feel and with less moving parts there will be less to go wrong down the road. You can also expect to get fps into the 400 range with a decent amount of shots per CO2 so the trade off not having blowback may be worth it for this reason. All in all a nice airgun in the under $100 category.
My Vimeo Videos for the KWC Metal Slide CQBP M45 A1 CO2 Air Pistol:
Trigger Pull: The trigger pull on the KWC Mac 11 M11 is double action only and is rather long and a bit firm so you will get a bit of a finger workout especially when shooting a full 39 rounds from the 4.5mm steel BB version. There is no blowback operation so this is a double action only pistol.
Accuracy: The accuracy and true feet per second performance will be tested when I do my future Field Test Shooting Review shortly (weather permitting).
Build Quality: Overall the KWC Mac 11 M11 CO2 BB - Airsoft Pistol is built fairly well as long as you don't mind the all plastic build. to be honest if you where to drop this all plastic pistol on the ground it would most likely just bounce a couple of times no worse for wear since it is kind of light weight and all. If it was an almost all metal build it would weigh in a lot more and the drop onto a hard surface could easily break the zinc alloy metal parts. That said there is some metal on the KWC Mac 11 M11 CO2 BB - Airsoft Pistol and that would be the folding - sliding stock and of course some internal parts. The rear fold out portion of the stock is actually hardened steel!
Realism: As a replica of a real steel Mac 11 M11, the KWC Mac 11 M11 CO2 BB - Airsoft Pistol looks bang on since it is 1 to 1 scale and at least in terms of looks is virtually identical ot teh real Mac 11. In terms of function, that is a different story since the KWC Mac 11 M11 CO2 BB - Airsoft Pistol does not have many working parts other than the trigger, safety and magazine release. The selector switch, bolt charging handle and bolt are all molded into this gun and their only purpose is to look good! The overall weight is rather light too since most of this Mac 11 pistol is ABS or plastic.
Pros:
First 4.5mm Steel BB Mac 11.
1/1 scale replica definitely looks the part.
Full size drop out magazine that holds the CO2 and BB’s.
High capacity 39 rounds magazine.
Built in metal and steel retractable stock.
Decent fps.
Available in both 4.5mm Steel BB and 6mm Plastic Airsoft versions.
Cons:
Pretty much all ABS, kind of light weight.
No blowback or many working parts.
Kind of long and heavy trigger.
Pretty much everything is moulded into this gun.
Comments:
Too be honest when I first saw the box for the KWC Mac 11 M11 CO2 BB - Airsoft Pistol I was a bit excited, that was until I opened it up and found out I was looking at a pretty much all plastic gun with few working parts and no blowback operation. But after holding it and giving this air pistol a good look over I have to say I am warming up to it a bit more now. After all it is the first Mac 11 M11 4.5mm steel BB pistol that I know of and it 100% looks the part so if you are looking for a replica Mac 11 then this will fill that purpose for sure. Even though it is almost all ABS plastic, this airgun feels solid seems to be really well made. The steel and metal stock is a nice addition and so would have been a metal magazine but overall for a low cost replica BB and Airsoft shooter you do get your moneys worth.
My Vimeo Video Review for the KWC Mac 11 M11 CO2 BB - Airsoft Pistol:
Trigger Pull: The trigger pull on the KWC Makarov PM CO2 Blowback BB Pistol is really nice. It is single action only since it is a blowback pistol that requires racking the slide to chamber the first round. The take-up of the trigger is slight with a crisp light release, the trigger is definitely not going to get in the way of the accuracy of this pistol.
Accuracy: The accuracy and true feet per second performance will be tested when I do my future Field Test Shooting Review shortly (weather permitting).
Build Quality: Excellent, the KWC Makarov PM CO2 Blowback BB Pistol seems to be really well built like the other full blowback KWC BB and Airsoft pistols I have reviewed and shot in the past. The fit and finish is very good but I expect the electromagnetic black coating to wear off in the high spots fairly quickly but this does give the slight worn in real gun look. In terms of quality it looks like KWC may have even gone to extra effort to beef up some of the areas perhaps prone to breakage like the trigger guard since this pistol is made out of Zink based metals rather than hardened steel like you would find in the real firearm.
Realism: I have to say the KWC Makarov PM CO2 Blowback BB Pistol is a really nice replica overall, perhaps one of the best considering it has full cycle blowback with an all metal full sized drop out magazine. Sure the Baikal MP-654K takes the cake in terms of realism since it is practically a real Makarov rechambered to shoot Steel BB's but the MP-654K lacks blowback operation and the ability to fire quickly using a single action trigger. A couple of drawbacks with the KWC Makarov PM CO2 Blowback BB Pistol that are different from the real steel Makarov PM are the thicker trigger guard and butt plate.
Pros:
Has full cycle blowback operation.
Nice heavy blowback spring makes slide nice and snappy, should have good blowback operation.
All metal build.
All metal full size drop out magazine that holds the BB’s and CO2.
Fully field strip-able.
All part function like a real Makarov.
Open ejection port and reassessed barrel.
No ugly CO2 tab.
Seems to have a really nice single action only trigger.
Internal fixed hop-up for improved accuracy and sustained trajectory.
Cons:
Lower fps because of short barrel and presumable heavy blowback operation.
Magazine base sticks forward a bit more and is thicker than a real steel Makarov.
Trigger guard looks to be thicker than a real steel Makarov.
Comments:
The Makarov is one of my favorite pistols, it's a true classic! So the fact that there is yet another Makarov Air pistol on the market is fine with me. And perhaps the KWC Makarov PM CO2 Blowback BB Pistol might just be the best all around Airgun Makarov hitting all the hot spots us Replica Airgun enthusiasts love... Like full blowback operation, a nice light single action trigger, a full size metal magazine that holds the ammo and the CO2 and of course an all metal build with all those working bits and pieces like you would find on the real steel Makarov PM. But you will have to decide for yourself...
My Vimeo Video Review for the KWC Makarov PM CO2 Blowback BB Pistol:
Wow! Some new 4.5mm Steel BB and 6mm Plastic Airsoft guns and they are all brought to us from KWC. I would expect all of them to be available eventually in both 4.5mm Steel BB and 6mm Plastic Airsoft but for now I have the M11 in both Steel BB and Plastic Airsoft and the Makarov PM and CQBP M45 A1 in Steel BB.
This is just my quick preview video so make sure to watch it as I do show you around the guns fairly nicely but you can expect some more upcoming detailed Table Top and Shooting Videos shortly...
Here are some of the basic specifications for each gun...
Ammunition Capacity: 15 round metal stick magazine.
FPS: 380 & 400 fps claimed.
Trigger Pull: Trigger pull on both the Umarex Beretta Elite II and Umarex HK45 is double action only but they don't feel too bad, they have that traditional longer double action pull but I did not find it to be too heavy and the release point is fairly predictable for me which should allow for some good overall accuracy when I do my future Field Test Shooting Review.
Accuracy: I have done a full Felid Test Shooting Review Video for the Umarex HK 45 Metal Slide CO2 4.5mm steel BB Pistol so make sure to check that one out! In summary with the 4.5mm Steel BB version I got a bit higher fps then claimed at 420 fps with a 5 shot string using a brand new CO2 with RWS 5.1 grain zinc coated steel BB's. From 30 feet away shooting on a paper target using a semi rested posting I was able to place 10 BB's within 1.5 inches, almost close to a 1 inch grouping. The shot placement for me was just a tad to the left and a bit down but several shots hit the bulls eye so out of the box accuracy was really good on this low cost BB pistol. Since both the Umarex Beretta Elite II and Umarex HK45 Airsoft pistols share many of the same mechanical qualities, I should expect similar results even using 6mm plastics BB's, perhaps a bit wider grouping but fps should be pretty close to claimed.
Build Quality: The Umarex Beretta Elite II and Umarex HK45 are built fairly basic with few moving parts so there is not much to go wrong, the fit and finish is good and there is metal where it needs to be internally and also in the trigger, magazine and on the HK45 even the slide. Both Airsoft Pistols have decent weight even though there is a fair amount of plastic in them.
Realism: Both Umarex Airsoft pistols are accurate looking replicas of their real steel counterparts, in the case of the Umarex HK45, it is very accurate on almost every detail appearance wise, the Umarex Beretta Elite II is not an exact replica of any one specific Beretta but is based on the Beretta Elite II Brigadier. There is no working slide on either pistol and the slide catch/release and hammer are molded into the plastic. The only working parts would be the safety, magazine release and trigger.
Both have tactical rails for adding on accessories.
Both are fully licensed.
Both have pretty decent weigh to them.
The HK45 has a metal slide and white dot sights front and back
The Elite II has white dot front sight.
Cons:
Both guns are double action only.
Both guns have none working hammers
Neither gun has a working slide or blowback action.
Both guns have red tips.
Non adjustable sights.
Comments:
Considering these Airsoft Pistols are rather low cost, the Umarex Beretta Elite II and Umarex HK45 have a lot going for them! They are fully Beretta and HK licensed through Umarex with a (metal slide in the HK45) and metal parts where you want and need them to be. I am expecting decent accuracy and power from both guns and even the double action triggers are very usable. Sure the both budget Airsoft pistols is a pretty basic airguns with few moving parts but then again simplicity is sometimes better in terms of reliability. If you are an Beretta or HK fan and want low cost well made and good performing Airsoft pistols then checkout these Umarex Airsoft guns.
My Vimeo Table Top Review for the Umarex Beretta Elite II and HK45 CO2 Airsoft Pistols:
Getting back to this Field Test Shooting Video, so how did the KWC Jericho 941 CO2 Airsoft Pistol perform for me? I was expecting some pretty decent fps performance sine the steel BB version was a pretty hot shooter but in Airsoft you don't always want crazy high fps performance or the gun may not be usable in any Airsoft games since it could injure an opponent. My 5 shot Chronograph test using .20 gram Airsoft BB's with a brand new 12 gram CO2 gave me an average of 438 fps which is about as fast as you are going to want an Airsoft gun to shoot. This pistol should be capable of hitting targets pretty far down range.
When I setup for the accuracy portion of my Shooting Field Test, as usual I stood 30 feet back from a paper target and used a semi rested stance (sand bag up front and standing in the back). My first round of 10 shots shot really high, with most of the shots hitting the target off camera. So I decided to take another 10 shots but this time with my aim point set at the bottom of the target. Using this method I was able to get all 10 shots fairly well centred on the paper target all within about 3 inches of each other. Not bad. So yes the KWC Jericho 941 CO2 Airsoft Pistol at 30 feet shoots a bit high but depending on what ranges you want it set for it may be just what you want?
The KWC Jericho 941 CO2 Airsoft Pistol is a double action only pistol without blowback operation so the trigger pull is longer and heavier then a blowback pistol with a single action trigger but I would have to say you can still rip off a bunch of quick shots regardless of the heavier trigger pull. In a nutshell the KWC Jericho 941 CO2 Airsoft Pistol is a really solid and consistent shooter with a fairly low price tag and the advantage of full size drop out metal magazines which are perfect for in field shooting.
I have already reviewed the 4.5mm Steel BB version of the ASG Bersa BP9CC and done both a Table Top Video and Field Test Video review for it so make sure to check those review video links out!
In this Field Test Shooting videos review I take the ASG Bersa BP9CC CO2 Blowback Airsoft Pistol through its paces and test it using my Chronograph to see what kind of real world fps we can expect from it. I also perform my usual 30 foot back paper target accuracy test to see what kind of a 10 shot grouping the ASG Bersa BP9CC CO2 Blowback Airsoft Pistol will achieve.
I have to be honest and say that there may have been a problem with the valve in my test unit since I was getting really inconsistent velocity readings using my Chronograph to test out the fps. I could even hear the difference in how much CO2 was being let out with each shot and even the recoil from the blowback slide was sometimes very hard and sometimes very soft. I did end up getting an average of 356 fps but it ranged anywhere from 420 right down to below 300 fps?
With the extreme velocity readings I was getting I did not expect the ASG Bersa BP9CC CO2 Blowback Airsoft Pistol to be super accurate as velocity can really effect the high and low target placement but I was surprised when pretty much all the shots hit within a 3 inch group, with the excepting of a double shot that obviously shot slow and low. This double shot was a result of the slide not kicking back all the way and not reset the single action internal hammer so when I pulled back the trigger I loaded a round into the barrel but could not fire the gun. Resulting in me having to manually pull the slide back and then pull the trigger back a second time, loading a second Airsoft BB into the barrel and firing both BB's at the same time.
My 4.5mm Steel BB version did not seem to have this inconsistent power problem so it may be that my gun either needed some break in time or perhaps had a faulty valve? Even so It actually performed well during the accuracy portion of the test for me.
Materials: Mostly metal with some plastic construction.
Weight: 2 pounds (900 grams).
Barrel: 2.25 inches, non-rifled.
Propulsion: 12 gram CO2.
Action: Revolver, single & double actions.
Ammunition Type: 4.5mm steel BB's.
Ammunition Capacity: 6 rounds.
FPS: 328 fps (120 m/s).
Trigger Pull: The trigger pull on the Gletcher CLT-B25 357 2.5 Inch CO2 BB Revolver is good in both single and double action, even better than the Dan Wesson and S&W 327 TRR8 shell loading revolvers, most likely because the spring tension that pushes the inner barrel to make contact with the cylinder is noticeably lighter on the KWC - Gletcher 357's. Even the hammer is smoother and has less wiggle, just a better trigger and hammer mechanism overall.
Accuracy: In terms of power and accuracy, you can checkout my full Field Test Shooting Video here. I did get a nice 2 inch 6 shot grouping on my paper target setup 30 feet away from my standard semi-rested position (sand bag up front and standing in the back). Accuracy was a bit lower than the factory claimed 320 or so fps coming in at an average of 280. I did perform my field test back in May so the weather was not all that warm perhaps effecting peek fps performance somewhat.
Build Quality: The Gletcher CLT-B25 357 2.5 Inch CO2 BB Revolver being mostly metal has a very good build quality, perhaps even better than the Dan Wesson and S&W 327 TRR8 shell loading revolvers, even the weight of the KWC 357 is noticeably more! The only real plastic or rubber I could find was in the grips and the shell tips. Fit and finish was also good with no noticeable wear or sloppy workmanship.
Realism: The KWC - Gletcher CLT-B25 357 2.5 Inch CO2 BB Revolver overall is a close copy a the real steel 357 styled revolver. I did notice the rear portion of the receiver (between the rear cylinder and hammer) to be a bit longer perhaps to accommodate the CO2 valve length, but other than that this pistol is super close to the original 357 styled revolver it is based on. Again being all metal gives this CO2 BB revolver very realistic weight and feel and the loadable brass shells make using this gun almost exactly like using a real shell loading revolver but for much less cost per shot and of course a lot less recoil on the hands that a real 357 magnum or even when shooting 38 special shells for that matter.
It's a revolver with actual shells! Give you the feeling of loading and shooting a real revolver
Mostly all metal design
lots of detail, well made, fit and finish are both good.
Good overall weight, even for this short 2.5 inch barrel version.
Fully adjustable rear sight for windage and elevation.
Well hidden CO2 Screw.
Recessed barrel.
Nice Trigger pull in both single and double action.
Tactical fingered grips look good and allow for a firm hold.
Cons:
Grips are a bit rough, not as rubbery as they look.
Grips may be a bit large for people with smaller hands.
All black sights not great on dark backgrounds.
FPS could be a bit higher!
Comments:
The Gletcher - KWC CLT-B25 357 2.5 Inch CO2 BB Revolver is yet another addition to the increasing lineup of shell loading revolvers available today in both Steel BB and Airsoft versions. The 2.5 inch reviewed here is meant to be the compact version with its snub nosed barrel but I would have to say it is not a small gun at all coming in at 2 pounds and with rather large grips and a pretty large cylinder to pack around. But then again, that may be just what you are looking for? The shorter barrel does effect the fps performance since longer barreled versions of this same pistol I have tested do shoot much hotter but that is to be expected with pretty much any short barrelled CO2 pistol.
My Vimeo Table Top Review for the Gletcher CLT-B25 357 2.5 Inch CO2 BB Revolver:
In this Field Test Shooting video I test out the performance of the KJWorks KP01-E2 (Sig Sauer P226) CO2 Blowback Airsoft Pistol using my Chronograph to get a real world (FPS) Feet Per Second rating. I also position myself 30 feet back and shoot 10 rounds at a paper target using a semi-rested shooting position (Sand bag up front and standing in the back).
In terms of velocity the KJWorks KP01-E2 (Sig Sauer P226) CO2 Blowback Airsoft Pistol shot a bit on the fast side at 414 FPS when averaging a 5 shot strong using .20 gram BB's with a brand new CO2. Keep in mind I was using the CO2 magazine which will have more power than the Gas Magazine version. I would assume the Gas mag version would shoot right around the mid 300's which may be more suited for indoor Airsoft games. For outside Airsoft wars you may want the extra power of the CO2 mag for shooting at targets further distances out.
Stepping back 30 feet and shooting at my paper target, the KJWorks KP01-E2 (Sig Sauer P226) CO2 Blowback Airsoft Pistol produced a decent 2 inch 10 shot grouping that was just a hair low but well centered left and right. The low factor could be adjusted up using some Hop-up tweaking. The trigger in single action mode is light and the release is crisp. Even the double action trigger is fairly light for double action, but there is a lot more take up since your finger is doing all the work that the blowback action would normally do for you when shooting in single action.
With the heavy blowback and high FPS the KJWorks KP01-E2 (Sig Sauer P226) CO2 Blowback Airsoft Pistol creates a really great shooting experience. It would be great for some target practice, getting some additional trigger time in if you are a Sig Sauer P226 owner and would make an excellent outdoor Airsfot war backup weapon. The quality is excellent and as a lover of the Sig Sauer lineup of guns I highly recommend this Airsoft pistol from KJWorks.
Here is my follow up Shooting Field Test video for my Cybergun Colt 1911 MKIV CO2 Table Top Review. During this Field Test Shooting video review I shoot 5 rounds of .20 gram Airsoft BB's through my Chronograph to find out the average FPS. I also step back 30 feet and setup my shooting stance by resting my hands on a sand bag and standing in the back for a fairly secure shooting position. As per most of my accuracy tests, I loaded my Cybergun Colt 1911 MKIV CO2 Blowback Airsoft Pistol with 10 rounds in the magazine to see what kind of grouping I could get on the paper target..
I was a bit surprised by the FPS for the Cybergun Colt 1911 MKIV CO2 Blowback Airsoft Pistol I tested. The claimed FPS by the factory is 360 using .20 gram BB's, the temperature outside was decently warm and I was using a brand new CO2 so I should have gotten fairly close the this velocity. As it turned out on this day the gun I was testing shot right around 300 FPS which is great for close quarters Airsoft games but perhaps a bit weak for the longer ranges of outside games.
When it came to accuracy, I did find the Cybergun Colt 1911 MKIV CO2 Blowback Airsoft Pistol shot a bit high and to the left right out of the box but since it has a fully adjustable trigger this did not concern me. I was pleased to see that I was able to get a 2 inch 10 shot grouping from 30 feet back using a semi rested position which is about right for an Airsoft Pistol at this range.
While testing the Cybergun Colt 1911 MKIV CO2 Blowback Airsoft Pistol I did not have nay mechanical problems, everything worked exactly as it was meant to , the Blowback was nice and crisp with that usually 1911 sluggishness I have come to expect. The trigger is pretty typical for a single action 1911 styled trigger which in some cases can actually be a little bit on the light side which with the Cybergun Colt 1911 MKIV CO2 Blowback Airsoft Pistol was not the case. Over all a really pleasurable Airsoft Pistol to shoot!
Ammunition Capacity: 19 round full size metal magazine.
FPS: 361 using .20 gram BB's.
Trigger Pull: The trigger pull on the Cybergun Colt 1911 MKIV CO2 Blowback Airsoft Pistol is exactly what you would expect from a true single action 1911 styled pistol. It has a short take up and then a nice light and crisp release. The working grip safety is a nice touch requiring your palm to be pressed against it for the trigger and hammer to operate. I also like the Tactical Style Trigger found on the Cybergun Colt 1911 MKIV.
Accuracy: At this point I have not shot the Cybergun Colt 1911 MKIV CO2 Blowback Airsoft Pistol, I imagine it should perform well considering it has spin-up up and a fully adjustable rear sight just in case my shooting is off center a bit. According to the manufacturers claimed fps, we should get somewhere in the mid to high 300 fps range using .20 gram Plastic Airsoft BB's.
Build Quality: I am kind of sitting on the fence with the Colt 1911 MKIV Pistol, on one hand it is an all metal gun with what looks to be fairly decent fit and finish but on the other hand it feels kind of light weight especially with the heavy magazine out of it compared to even the KWC 1911's I have reviewed so often. It may be that more aluminum is being used in this pistol which could actually be a good thing since aluminum would be a higher quality metal over your typical zinc alloy used in most Airsoft and Airguns these days. In terms of operation, I feel like some of the mechanical parts need a bit of break in time, but I have found this to be true with many real guns I have used.
Realism: The Cybergun Colt 1911 MKIV CO2 Blowback Airsoft Pistol is a close replica of the real steel Colt 1911 45 auto but with a more modern Tactical look to it, sporting a Tac style trigger and hammer, double stack magazine, ambidextrous safety and adjustable rear sight. This gun is nearly all metal with very full blowback operation making it feel real to hold in the hand and shoot.
True 1911 single action trigger, excellent pull, very smooth and light.
Accurate trigger design and working grip safety.
Double stack metal magazine holds the CO2 and extra BB’s.
Fully Colt Licensed.
Full adjustable rear sight.
Tactical trigger and hammer with ambidextrous trigger for a more modern look and feel.
Cons:
Comes with the ugly red tip that is really stuck on the gun.
Can kind of tell the Chinese quality a bit.
Licensing is not engraved right into the gun.
Comments:
Overall the Cybergun Colt 1911 MKIV CO2 Blowback Airsoft Pistol is another nice option if you're looking for a Colt Government 1911 Styled Airsoft pistol. Keep in mind this one is Chinese made rather than made in Taiwan. Not sure how that will effect performance and longevity. I have owned Chinese guns that have shot and faired well for me so I am not too worried about it. With its double stack magazine you will find the Cybergun Colt 1911 MKIV to have a fairly large handle so it may not be suitable for those with smaller hands. I do think the Cybergun Colt 1911 MKIV CO2 Blowback Airsoft Pistol features a nice combination of classic Government 1911 looks with a few modern tactical components lie the upgraded trigger, hammer, ambidextrous safety and rear adjustable sight.
My Vimeo Video Review for the Cybergun Colt 1911 MKIV CO2 Blowback Airsoft Pistol:
Trigger Pull: The trigger pull on the KJWorks KP01-E2 Sig Sauer P226 Airsoft Replica is good in both single and double action. Once the slide is pulled back and released the first round is chambered and the hammer will remain back placing the KJWorks P226 in single action mode, the pull is light and the take-up is nice and short, most of your shots will be in single action mode unless you use the de-cocker to lower the hammer for a subsequent double action follow-up shot, double action shots are still pretty light but much longer in order to cock the hammer back.
Accuracy: (I have not shot the KJWorks distributed CO2 Mag version but I have already done a Field Test Shootinng Review for the same KJWORKS gun distributed and licensed by Cybergun in the Gas Mag version. Here is what I had to say about the Cybergun Gas Magazine version: "Shooting the Cybergun Sig P226 from 20 feet out in semi rested position I was able to get very good results. I placed 10 rounds in about 1.5 inches with the shot placement being a bit low possibly due to my barrel mod, adjusting the hop-up may bring the aim point back up to where it should be. The Sig Sauer P226 Airsoft Replica shot right around the 316 fps range while conducting my 5 shot average chrony testing which was lower than advertised but I was using much heavier .20 gram BB's. You can expect to get a full magazine worth of shots out of each gas fill-up but I did notice that as the magazine got colder it did tend to become much less efficient and also seemed to vent a lot of vapor."
Build Quality: The build quality for all KJWorks guns in my opinion is one of the best in the business. Fit and finish is top notch with close tolerances in the working parts as you would find in a real steel gun. The paint is excellent and in general will wear much better than other Airsoft guns out there. The KJWorks KP01-E2 (Sig Sauer P226) CO2 Blowback Airsoft Pistol is pretty much all metal and feels it, the recoil spring is nice and firm and all working parts are smooth and crisp when operated.
Realism: The KJWorks KP01-E2 (Sig Sauer P226) CO2 Blowback Airsoft Pistol is a replica of the real steel Sig Sauer P226 with the exception of the licensing. The KJWorks KP01-E2 really is a great looking and functioning Airsoft Replica. You can field strip this gun exactly like a real Sig Sauer and all the mechanical parts work just the same including a working de-cocker and adjustable front sight. It is really hard to distinguish the Airsoft version from the real Sig P226 in both looks and feel.
All metal pistol with good overall realistic weight to it.
Very crisp and firm full blowback operation.
Some of the best fit and finish in the industry. Especially in price range.
Nice accurate looking and working Sig Sauer P226 Replica.
Working de-cocker.
White dot sights for quick target acquisition.
Front sight is adjustable for windage.
Full size drop out magazine holds Airsoft BB's and CO2.
Fully field strip-able.
Cons:
No actual Sig Sauer Licensing but very clean look.
CO2 Mag does stick out a bit and add to size
Comments:
I am a huge Sig Sauer fan so I have kind of high expectations with a replica gun! The KJWorks lineup as a whole is really fantastic, and what I say about the KJWorks KP01-E2 (Sig Sauer P226) CO2 Blowback Airsoft Pistol can be said about the entire lineup. KJWorks makes a super well built product that replicates the real steal version almost exactly other then they shoot Airsoft BB's instead of actual bullets. When holding a KJWorks gun in the hand you can feel the quality, in weight, ballence and especially when operating the slide, trigger and other working parts. Everything just feels so perfect and responsive. For the money you can not go wrong with the KJWorks KP01-E2 (Sig Sauer P226) CO2 Blowback Airsoft Pistol or any other KJWorks gun for that matter.
My Vimeo Table Top Review of the KJWorks KP01-E2 (Sig Sauer P226) CO2 Blowback Airsoft Pistol:
Ammunition Capacity: 19 round metal stick drop out universal magazine.
FPS: 394 fps 120 m/s.
Trigger Pull: The trigger pull on the Gletcher BRT 84 is rather long and a bit on the heavy side but it is smooth and predictable. The release point takes a while to get to but once you figure it out you can get really accurate shot placement with this Beretta Model 84 replica. As with many low cost simplicity designed CO2 Air Pistols, the Gletcher BRT 84 uses the barrel like a hammer. When you pull the trigger, the inner barrel moves forward and out of the outer barrel allowing a BB to move into the breach area, then the barrel snaps rearward hitting the CO2 valve releasing CO2 and shooting the BB.
Accuracy: I tested the Gletcher BRT 84 All Metal CO2 BB Pistol from 30 feet back shooting at a paper target using a semi rested position I was able to get a near 1 inch 10 shot grouping on two separate occasions with this rather small and unassuming airgun. In terms of feet per second performance the Gletcher BRT 84 All Metal CO2 BB Pistol is rated at 394 fps, my Chronograph results shooting 5 rounds through the Chrony using a full CO2 and 5.1 grain Steel BB's was a respectable 421 fps, even a bit higher then the factor claim of 394.
Build Quality: Being a pretty much all metal gun, makes the Gletcher BRT 84 All Metal CO2 BB Pistol feel solid and sturdy even for such a small pistol. The only plastic parts on the Gletcher BRT 84 are the grips, the CO2 tab and perhaps an internal part like seals and such. The painted finish is a nice dark grey and seems to be wearing really well. Since the Gletcher BRT 84 All Metal CO2 BB Pistol is basically a one piece solid metal moulded airgun, there is really nothing to go wrong and no fit problems to speak of. Yes it is basic but it is also really well made.
Realism: The Gletcher BRT 84 All Metal CO2 BB Pistol is a replica of the real steel Beretta Model 84. It is an extremely close copy in terms of looks and feel, but does not have very many moving parts other than the trigger, magazine release and safety. So no slide movement or blowback, no working slide catch release, not even the hammer is functional. That said, not much to go wrong if what you are looking for is a gun that looks like a Beretta model 84.
Very solid all metal construction, good weight and feel.
Stick magazine is universal and can be used in many other guns.
Very accurate with good fps performance.
Grips feel nice, almost have a rubber like texture.
Simple design so not very much to go wrong with this airgun.
CO2 tab is hidden internally.
Reasonable price tag for well built all metal airgun.
Cons:
Very few working parts.
Trigger is a bit long and heavy, not ideal for action shooting.
Sights are non-adjustable
No Beretta Licensing
Comments:
I am usually not a huge fan of non-blowback basic airguns, especially when they do not have many working parts on them. However the Gletcher BRT 84 All Metal CO2 BB Pistol has some strong points that makes it worth considering, like it's solid all metal build, excellent accuracy and nice high fps performance for such a small sized airgun. It all feels really good in the hand ergonomically and based on the way it's built in such a simple no frills manner, the Gletcher BRT 84 All Metal CO2 BB Pistol should last a long time if taken care of.
Watch my Vimeo Review for the Gletcher BRT 84 All Metal CO2 BB Pistol:
Action: Semi auto non-blowback, double action only.
Ammunition Type: Airsoft plastic 6mm.
Magazine Capacity: 15 rounds
FPS: ? (1.6 Joules)
Trigger Pull: The trigger pull on the KWC Model 1911 All Metal Non-Blowback CO2 Airsoft Pistol was about medium to hard but I have definitely experienced heavier trigger pulls on many double action only Airguns. It is nice that the trigger has the look of a 1911 and not your typical lever styled trigger. I did find the trigger to be very usable and the release point is smooth and fairly predictable.
Accuracy: I have yet to perform my field test shooting component for the KWC Model 1911 All Metal Non-Blowback CO2 Airsoft Pistol, however I have reviewed the same gun in 4.5mm Steel BB Cybergun version and here is what I had to say about that the Steel BB version: "Accuracy was decent but not outstanding, I got around a 2.5 inch grouping from a 20 foot away free standing position, shooting just to the left and high on the target. I did find that I was able to zone in a bit better with the Cybergun GSR 1911 as I got used to the trigger. I also put the Cybergun Sig Sauer GSR through my Chrony Chronograph and got very close the manufacturers 397 claimed feet per second, actually starting off well above it and settling down to around the 370 FPS mark. My 8 shot average on a new CO2 was actually 422 FPS."
Build Quality: The build quality for the KWC Model 1911 is very good, this is an almost all metal Airsoft gun with a few exceptions like the hammer, trigger. magazine release, slide catch and grip safety. Pretty much everything else is metal including the slide, frame, magazine, and even the grips. The finish is very good and since there is lots of metal with minimal moving parts and less to go wrong, this should make for a very reliable pistol.
Realism: The KWC Model 1911 CO2 Airsoft Pistol is very close to the look, weight, and feel of the real steal Sig-Arms 1911 GSR! Even the 1911 style trigger was replicated as best as it could be given it being double action only. It would have been nice to have a single action trigger and a working slide to finish off the illusion but overall the GSR is a really nice copy of the real steel Sig Sauer GSR Sig-Arms 1911 firearm.
Very Accurate Sig-Arms Sig Sauer 1911 GSR Replica.
Should have good FPS and lots of shots per CO2 based on my 4.5mm BB version testing!
Very affordable and good value for the money.
Rail for mounting accessories.
Nice sights with white dots front and back.
Recessed barrel for added realism.
True 1911 style trigger even though it is double action only.
Very affordable price tag.
Cons:
Non-blowback and the slide does not move either.
The hammer is only for show and does not cock for single action shots.
Trigger action is bit heavy but not not too bad for a double action trigger.
Non adjustable rear sights.
Comments:
For a relatively inexpensive All Metal Airsoft gun you get a lot for your money with the KWC Model 1911, most importantly a very accurate reproduction of the real steal Sig-Arms Sig Sauer 1911 GSR firearm! If you're a 1911 fan and want to pick up an Airsoft gun that won't set you back too much, then the KWC Model 1911 would make a great choice with it's heavy full metal weight, full size drop out metal magazine, accurate reproduction of the real steal Sig-Arms GSR and again that very affordable price tag.
My Vimeo Videos for the KWC Model 1911 CO2 Airsoft Pistol:
