I will be doing proper Table Top and Field Test Videos for each of these Airsoft guns as soon as I can get to them all, starting with the Umarex Gas Blowback H&K MP7 A1 Airsoft PDW so stay posted for these upcoming video reviews...
I finally got out to shoot my Wyoming Arms Parker 10mm S.S. and it worked pretty well for me, the kick was hard but the design of this 10mm pistol helps reduce recoil so the recoil was not really all that much more than shooting a .45 or .40 caliber. If you have not watched my Wyoming Arms Parker 10mm S.S. Pistol Real Steel Overview then make sure to do so... I did have a few of my reload rounds that seemed to give me a bit of trouble but other than that the Wyoming Arms shot very well for me and was extremely accurate.
I also brought along my little ISSC M22 .22LR shooting Glock look-a-like to keep some of my shooting costs down since the 10mm are so expensive I needed to recoup some of my costs shooting the super affordable .22LR ammo. And yes I have a full Table Top Review for the ISSC M22 so check that one out if you're in the market for a fairly low cost .22LR that looks a lot like a Glock.
I had a great time and we got to shot some other guns while we where at the gun range; Walther P38 9mm, Glock 22 .40 Caliber, Sig Sauer Mosquito .22LR and the Smith & Wesson M&P 15-22 .22LR in all.
After many many requests to show how the Umarex Walther PPK CO2 Tab Modification is done I have relented to public demand. I don't actually cut my tab in this PPK CO2 Tab Modification Video but I do go step-by-step in detail and compare my modified Umarex PPK to my unmodified Umarex PPK. It is really very basic on how this is done and only a hack say and perhaps a file are all that is required to make the modifications to the PPK CO2 tab in order to make it flush with the bottom of the handle area.
Your best bet is to simply watch my YouTube Video located below and follow the steps there but here it is in text form:
Place an empty (already pierced) CO2 into your Umarex Walther PPK and tighten the unmodified CO2 tab until fully tightened, just like you would tighten a fresh CO2.
Take note at how many threads are exposed between the bottom of the handle and the top of the plastic CO2 tab, there should be about 2-4 threads exposed.
Unscrew the CO2 tab all the way, place the PPK BB Pistol so it is secure (in a vice of some sort) and use a hacksaw or dremel to shorten the CO2 screw just above the plastic tab at the thread location you previously noted. Be conservative as you can always cut or file the screw a bit shorter if your first cut was not short enough.
Now use the same hacksaw or dremel to cut a notch in the exposed cut area of the CO2 screw so that you can use a slot screwdriver to tighten the CO2 screw.
That's it - Enjoy your modified Umarex Walther PPK CO2 BB Pistol!
Watch my Vimeo Video of the Umarex Walther PPK CO2 Tab Modification Tutorial:
Testing out the ASG - Marushin CZ 75 Blowback Shell Ejecting Airsoft Pistol was not an easy one but I did manage to get thorough it! First there was the setup, I could not shoot the ASG Shell Ejecting CZ 75 Airsoft pistol on my deck or I would have fore sure lost most of my shell casings for it. So I decided to setup camp in my pool area where I have a nice large flat area off to one side, I put down a ginormous tarp in hopes to catch the radically flying shells but even this failsafe did not catch them all as I later found out ;)
As with most of my Field Test Shooting videos, I usually do a bit of a pre test to make sure the gun is functioning properly and so I shot a full magazine of my brass shells through the ASG CZ 75 and it worked like a charm, of course when I started recording the live video it decided not to work at all and I still do not know why? I was able to revert back to the plastic shell casing that came with my ASG CZ 75 Blowback Shell Ejecting Airsoft Pistol and they seemed to be working so I went with them for my testing. Interestingly enough the brass shells got much higher fps (around 300+) when I did my pretest compared to around the 250 average fps I was getting with the plastic shell casings.
Shooting on target proved to be better than I though once I raised my sight point up a bit, the gun likes to shoot a bit low but once I found the sweet spot I got three rounds within about 3/4 of an inch from just over 20 feet away in a semi rested position.
I would not recommend this Airsoft gun as an everyday shooter and there is no way you could use it in any type of Airsoft simulation as the ejected shell casings would get lost for sure and the cost to shoot the ASG CZ 75 would get very high indeed! It would be good for use in a movie or video where you wanted the realistic look of shells being ejected and did not want to use a blank gun or render the shells in post. And of course it is just really cool to have an Airsoft gun that has ejecting shells :)
Materials: Plastic slide & frame, some metal parts.
Weight: 1.4 pounds (616 grams).
Barrel: Metalnon-rifled smooth bore.
Propulsion: Propane, green gas.
Action: Blowback, single action only.
Ammunition Type: 6mm plastic Airsoft BB's.
Ammunition Capacity: 8 rounds.
FPS: 279+ fps.
Trigger Pull: The trigger pull on the ASG CZ 75 Shell Ejecting Airsoft Replica is single action only, unlike the real steel version that actually has a single and double action trigger. The single action trigger has a light to medium pull but does have a fair bit of take-up to it.
Accuracy: I did not pre-test the ASG CZ 75 as the shells fly everywhere and you really need to be able to retrieve them afterwards as the cost to replace the shell casing is rather high. I do plan to do a full Shooting Field Test where I will shoot the ASG Shell Ejecting CZ 75 through the chronograph, place some shots on a target and also capture the action of this pistol in slow motion with a high speed camera. So stay posted for that. I can say that from the few shots taken in my house, that it seems to shoot pretty hard and the shells really com flying out of this gun with force, I also noticed that a BB does have to be loaded into each shell for there to be enough back pressure to allow for a full slide blowback and ejection of each shell.
Build Quality: Even though this gun is made mostly out of plastic and from what I can tell is also made in Taiwan, it has a very good overall fit and finish. The slide slop is next to none and the licensing and markings look great. There are metal parts where they really need to be like in the barrel, hammer, trigger, safety, slide catch, magazine and a few other internal parts.
Realism: The ASG Shell Ejecting CZ 75 Airsoft Pistol is one of the most ultra realistic Airsoft pistols I have seen and mimics a real steel gun right down to the shells being ejected, how cool is that! If it had more metal then that would really top it off. Even with the plastic slide and frame it is very realistic in almost every way and even field strips just like a real CZ 75 and is fully licensed. The only feature not true to the actual CZ 75 would be the single action only trigger.
Excellent fit and finish - tolerances are very good.
Very believable working replica of the real steel CZ 75.
Fully licensed.
Fully field strip-able.
Nice heavy full size drop out metal magazine helps give it some needed weight.
Has metal parts where they need to be.
Cons:
Plastic slide and frame.
A bit low in the FPS department.
Only 8 rounds in the magazine.
Can not really use in the field, would lose too many shells.
Comments:
The ASG CZ 75 Shell Ejecting Blowback Airsoft Pistol is a very unique Airsoft gun, not very many Airsoft guns actually have ejecting shells. Just because of that I had to have it! Overall it is a pretty decent gun but I have yet to really test it out and that is the biggest shortcoming with this gun, you can't just shoot it anywhere as you need to shoot it in a place where you can recover your spent shell casings, unless of course you have all the money and shell cases in the world... That said it has a lot going for it other than the ejecting shells; Fully licensed and trademarked, blowback operation, full size drop out metal magazine and it's fully field strippable. I am sorry to say we don't offer it in out Canada or USReplica Airguns Store but we do have a similar all metal CZ 75 Airsoft offering in the form of the KJWorks KP-09 which I have done both a Table Top and Shooting Review for.
I do get requests from many of my viewers to do some real steel reviews and so far I have pretty much stuck with 22LR real steel reviews and my Tokarev real steel review. I recently purchased an interesting 10mm semi auto handgun used at a local used gun show and so I though I would share this rather interesting and no longer in production pistol with you. The handgun we are looking at today is the Wyoming Arms Parker 10mm S.S. At first place it looks a lot like a 1911 but it is different in several ways. the obvious traits are the safety on the slide and lack of a grip safety, it also has a very different looking handle and there are some internal differences also.
What drew me to the Wyoming Arms Parker 10mm S.S. was it's 1911 looks, the very nice stainless steel finish and the rather unusual 10mm ammo it was chambered to shoot. If your not familiar with the 10mm round it was developed by the FBI for sue by their field agents but was later determined to be a bit too much to handle for some of their smaller but later agents. The 10mm was then detuned and turned into the S&W 40 caliber which is essentially a shorter less powerful version of the 10mm.
Here are a bunch more photos that really show off the beauty of this pistol!
Definitely make sure to watch this video as I go through the gun and show you around, I also do a field strip and talk a bit more about the Miami Shootout that was the FBI's reason to look into the development of the 10mm Auto round.
We have been taking preorders on many of our ASG Airguns and Airsoft guns for our Canada Replica Airguns Store, we where expecting them to be back in stock right around the end of the month. The good news is we got them a bit early so we are now filling back orders and most of our ASG inventory is now showing as in stock and ready to ship!
So if you've been waiting for an ASG gun, make sure to grab yours now before we run out again...
This is not meant to be a full review of either the BB or Airsoft version of the Cybergun - KWC CO2 Blowback Mini UZI's but I do talk about specifications, show you around both guns, and put them both through a full Field Test so I guess in a way, perhaps it can be considered to be a full review ;)
I will list the specifications here for you but I am not going to get into details like Trigger Pull, Build Quality, Accuracy and Realism. You can check out my other video reviews for more information on the Mini UZI:
As I said you can check out all my other videos for info on these very accurate Mini UZI Replicas, I mainly want to go over some of the main differences and similarities for both the BB and Airsoft versions.
In terms of build quality they are made almost exactly the same and weigh in at a hefty near 5 pounds, the only differences are the inner barrel and magazines to accommodate the different sized ammo. The BB version has a 25 round single stack magazine that does not have a follower to stop the bolt from continuing to operate even after the magazine is empty. While the 6mm Airsoft version has a double stack magazine that holds 38 rounds and does have a follower to stop the bolt which can save you some unintentional wasted CO2.
The Airsoft Mini UZI version is distributed by KWC while the 4.5mm BB version is distributed by Cybergun, you will find the UZI and IWI licensing on the Cybergun 4.5mm BB version but not on the KWC 6mm Airsoft version.
Out of the box the KWC Airsoft Mini UZI is ready to go in both semi auto and full auto while the 4.5mm steel BB version will only shoot in semi auto mode, it can however be easily modded to shoot in full auto.
Both guns come in cardboard boxes with manuals, some BB's and an Allen key to tighten the CO2. The KWC Airsoft Mini UZI also comes with a handy speed loader.
There is a slight fps velocity difference between the two with the KWC Airsoft 6mm plastic rounds traveling at around 400 fps (with .20 gram BB's) and the 4.5mm Steel BB's traveling at right around 350 fps. In the field test portion I test both guns out on some water filled cans to see how each ammo type performs in terms of penetration.
Your best bet is to watch both my Table Top and Field Test Comparison Video Reviews and see for yourself how they compare!
Earlier this week my father called me up and asked if I wanted to head out with him to go do some hunting/shooting. He has his bear tag but for the most part, hunting with my Dad consists of driving around in his truck hoping to stumble on something since he can not walk all that far these days.
We had a great time just enjoying each others conversation and of course the beauty of Canada BC's Harrison Lake area. We also got to shoot some guns to "make sure they where sighted in and working correctly". I brought my Norinco 12 Gauge Homeland Security 780 which I needed to test out and I'm glad I did since it needs some TLC to get working smoothly. I also brought along my little Henry Lever Action 22LR which is always a blast to shoot. My Dad brought his Savage Arms 7mm Magnum just in case we did see a bear on this outing.
Long story short we didn't bring any meat back home with us but we did see some out of season doe and of course had some nice father-son time together...
For the most part, this video is to test out some cameras and using them all together in a multi-camera scenario. I wanted to see how many camera angles I could shoot at one time and see how they would all work together when editing the video.
Cameras used:
My new Pivothead Recon Camera Glasses.
Sony HDR-AS15 Action Cam.
Drift HD170 Point of View Camera.
Nikon 1 with 10mm fixed lens.
Casio TRYX.
*All cameras where shooting in 1080p for this video.
I hope to use camera setups like this in the future, maybe not all at once but at least a couple at a time to give you some viewing options.
I picked out my WE SCAR GBB Airsoft Rifle for this test as it had a lot of mounting points and the Gas Blow Back makes for some great video action. Unfortunately My WE SCAR was not working at 100% but I still think I was able to pull off this test video either way.
Watch my Multi-Camera-Angle Test Video shooting the WE SCAR GBB AIrsoft Rifle:
Here is my official Field Test Shooting Video Review for my Daisy Winchester Model 11 CO2 Blowback BB Pistol. Make sure to checkout my previous Table Top Review for more details on the Winchester Model 11 1911 CO2 4.5mm BB version where I also did a pre-test showing similar results.
My 5 shot Chronograph test resulted in a bit lower than previously tested 339 average fps while my accuracy test shot from 20 feet out in a semi rested position got six shots right in the 1.5 inch bullseye with 4 shots coming out a bit, 2 of which spread the group out to about a 3 inch grouping in total. So in terms of shot placement you could say the Daisy Winchester 1911 4.5mm BB Pistol shot very well centered. Agin this time around I got 6 full magazines but had to manually clock teh hammer back on some of the last magazines end shots, power did seem OK even when manually cocking the hammer.
Overall, the Daisy Model 11 4.5mm BB Pistol is nice pretty much all metal low-cost CO2 Blowback BB pistol with good overall performance. This one looks the part of a 1911 even though it may not function 100%. If your OK with close and want to save a few bucks, then teh Daisy Winchester Model 11 may be for you, if you don't mind spending a bit more to get a BB gun as close to a real 1911 A1 as possible than take a look at the KWC/Cybergun Tanfoglio Model 1911 full blowback BB Pistol and Airsoft Pistol versions.
Here is my official Field Test Shooting Video Review for my KWC Sigma SW40F CO2 Blowback BB Pistol. Make sure to checkout my previous Table Top Review for more details on the KWC SW40F 4.5mm BB version where I also did a pre-test showing some similar results.
My 5 shot Chronograph test resulted in a somewhat expected 285 average fps while my accuracy test shot from 20 feet out in a semi rested position received a slightly wider 3 inch group this time but with most shots being within 1 inch of each other. In terms of shot placement the KWC SW40F 4.5mm BB Pistol shot very well centered but just slightly low. I also only got 2 full magazines this time around so don't expect a lot of shots per CO2 with this 4.5mm BB pistol.
Overall, the KWC SW40F 4.5mm BB Pistol is a really fun gun to shoot with a very crisp heavy slide that gives a nice firm blowback snap to it. It is one of the nicer sounding slides with a less tinny sound than most. The fps and shots per CO2 is a bit low but other than that performance is very good, you will have no problem nocking down cans and acquiring other miscellaneous targets.
ALL GUNS ARE NOW SOLD - THANKS FOR THE AWESOME RESPONSE!
This is a first for me but I guess you could say I have to make room for some more guns ;) I have some duplicate guns and a couple I juts don't have a need for anymore so instead of having them sit around collecting dust, I thought I would offer them up for sale and get them in the hands of someone who can really appreciate and get some use out of them...
Here is a list of the items up for sale:
Baikal IZH-61 .177 Caliber Spring Piston Pellet Rifle: $115
Baikal MP-655K Pellet/BB CO2 Pistol (missing pellet magazine): $125
Umarex CP99 Compact CO2 BB Blowback Pistol: $50
Swiss Arms Sig Sauer GSR 1911 CO2 BB Pistol: $30
ASG CZ 75 P-07 DUTY Dual Tone CO2 BB Blowback Pistol: $125
Umarex Beretta M92FS .177 Caliber CO2 Pellet Pistol - Nickel with Wood Grips: $200
(2x) AK47 BB Gun Magazines: $50 Each
Crosman 2240 .22 Caliber CO2 Pellet Pistol (14 inch barrel, RJMachine Breach/Brass Bolt, Wood Grip, NcSTAR 6x32 Scope): $225
Shipping/Handling is $15 Canadian and $25 to the US and you must be 18 or over to buy. You will need to email me at mike@replicaairguns.com to let me know what gun/guns you want to buy - first come first serve, I will send a PayPal request to the person with the first offer to buy and give them 24 hours to pay or I move on to the next buyer.
You can watch my YouTube Video to get a good look at each pre-owned item up for sale:
The KWC/Cybergun Model 1911 Blowback BB Pistols and Airsoft Pistols are very popular and so I tend to get lots of questions about them like: Are they the same quality? What version shoots the best? How do I remove the white warning lettering? Can I get one in an Airsoft version? Can I add a laser or tactical light? Can I change the grips...
So in this YouTube video I compare all four existing KWC and Cybergun model 1911's showing you the Cybergun Tanfoglio Witness 1911 in 4.5mm Steel BB, the KWC Model 1911 and Model 1911 A1 Tac also in 4.5mm Steel BB and lastly the KWC Model 1911 in 6mm Airsoft plastic BB.
Watch my Vimeo Video of these four KWC and Cybergun Model 1911 4.5mm Steel BB and Airsoft CO2 Blowback Pistols:
Trigger Pull: The trigger pull on the Daisy Winchester Model 11 is very nice, just about the perfect pull weight, not too heavy or too light, it has next to no take-up at all and a nice predictable release point. As is traditional with a 1911 styled pistol, the trigger is single action only so you will need to either pull the hammer back or rack the slide for the first shot, with subsequent shots you will not have to do this as the blowback action cocks the hammer for single action shooting. If your CO2 is very low, the blowback may not be adequate enough to cock the hammer so you can do this manually to get a few extra shots out of the Daisy Model 11.
Accuracy: When I shot the Winchester Model 11 from 20 feet out in a semi rested position, I was able to get some decent results. I placed 10 rounds within about a 2 group and the shot placement was very well centered, just a slight bit to the left. I did get a couple of stragglers that spread the group out just a bit larger but not too much. I did also get right around 350-360 fps on my chronograph on this not so warm day. We will have to see what my dedicated field test results yield for this BB pistol.
Build Quality: The Daisy Model 11 (1911) is made in Japan and has a nice overall finish to it. Other than the plastic magazine and grips it is an all metal gun so the materials used are good. The slide does have a bit of wiggle play in it but so do many blowback air pistols, perhaps to reduce some friction as the slide springs on these guns are not overly heavy. The paint used seems to be holding up very well and looks good, I did notice a molding seem that runs down the underside of the slide and along the trigger guard.
Realism: The Daisy Winchester Model 11 is a replica of the real steel 1911 A1 style 45 auto. It does have the Winchester licensing on it but I am not sure if there is an exact Winchester 1911 this gun is made to replicate. For the most part it looks and functions very similar to a real 1911 with a few exceptions like the lack of a working grip safety, a rather strange two stage safety and also the stick styled smaller magazine. This blowback air pistol can not be field striped conventionally either. I do like the true single action trigger and open ejection port.
Lots of metal in this airgun and good weight to it.
Good overall looking replica of a real 1911.
Reasonably decent blowback feel.
Mid range fps and shots per CO2.
Very nice true single action trigger.
Shots where well centered and got decent accuracy.
Markings and instructions on gun are color matched.
Solid CO2 tightening system, seems to work well once you get the hang of it.
Not bad at all for the lower price point.
Like the open ejection port.
Made in Japan.
Cons:
Kind of funny safety setup, it is redundant?
Has a plastic magazine, would have been nice in metal.
Back strap safety does not actually work but it does move.
Says "clip" instead of "magazine" on gun.
Comments:
I know some people have been hating on this gun for a couple of reason so let's get them out of the way... Yes it has a weird safety setup and I can not tell you why Daisy did this, perhaps they wanted it to be "more safe"? As a 1911 trainer you will have to adapt how you take this gun off of safety over a traditional 1911 setup. The magazine is plastic, not a biggie, if it breaks on you get another one. It's not full blowback like the Cybergun/KWC Tanfoglio 1911, this is true but you do get higher fps and more shots per CO2 out of it because of this. And yes Daisy uses the word "Clip"on the gun instead of the correct term "Magazine". Honestly, the Daisy WInchester Model 11 is a nice overall BB gun and the price point is pretty low for what you get. It looks really good overall and shoots nicely with enough blowback to give you some recoil feel and allow for true single action shooting. You also get decent fps and a good amount of shots from a single CO2 cartridge so stop complaining and just enjoy this gun for what it is!
My Vimeo Table Top Review of the Daisy Winchester Model 11 Blowback CO2 BB Pistol:
Trigger Pull: The trigger pull on the KWC Sigma SW40F CO2 Blowback BB Pistol is single action only which generally produces a very light trigger, on the SW40F it is a bit firmer than most single actions but still decent with a short take-up and firm release. You will need to pull the slide back (which also chambers your first round) to cock the internal hammer, after which subsequent shots you will not have to pull the slide back as the blowback action does this for you.
Accuracy: When I shot the KWC Sigma SW40F from 20 feet out in semi rested position I was able to get nice clean results. I placed 10 rounds within about 2 inches with the shot placement being very well centered. The KWC S&W Sigma SW40F seemed to keep the rounds tighter from top to bottom over side to side for me. I also noticed when I field stripped this gun that there is a built in hop-up (rubber bar) that sits inside the barrel, this will produce some back spin which will keep the BB's trajectory a bit flatter when shooting further out and is also probably there to stop BB's from rolling out of the barrel once chambered.
Build Quality: The build quality is about the same as all other KWC guns, tolerances seem tight and everything is working as it should, you will get some wear marks (paint wear) on the high spots over time which is normal on just about any (type of gun, real or air) but what I like about the SW40F is that the barrel is polished and since this is the first area to lose paint, it really does not matter since no paint is on the barrel.
Realism: The KWC Sigma SW40F CO2 Blowback BB Pistol is a replica of the real steel S&W Sigma with the exception of the licensing and it really is a bang on Replica, you can field strip this gun exactly like a real Smith & Wesson Sigma. All the mechanical parts work just the same and I like the fact that without the licensing, this gun is very clean looking with no obtrusive warning instructions on it.
Lots of metal in this gun with very good weight to it.
Very accurate S&W Sigma replica.
Heavy crisp blowback feel.
Predictable single action trigger.
Shots where well centered, got good accuracy.
White dot sights for quick target acquisition.
No ugly warning markings.
Full size drop out magazine holds BB's and CO2.
Like the polished barrel and ejection port.
Fully field strip-able.
Cons:
I only got two magazines in my pre-test for some reason?
FPS is not super high?
A bit finicky when loading BB's
Comments:
Just like my Airsoft review of the KWC Sigma SW40F, this blowback Air Pistol was a lot of fun to shoot, with it's super snappy heavy slide and ultra realistic shooting characteristics. It did seem to go through a lot of CO2 very quickly which is not uncommon for this style of full blowback heavy slided airgun, and to be honest I don't really mind since it shot well, felt good in the hand and backs it up with great looks. And heck it's still so much cheaper to shoot than a real 9mm hand gun ;) For those of you looking for something that is similar to a Glock in terms of looks and operation, the KWC Sigma BB or Airsoft pistol may be your only real option here in North America now that the Umarex SA177 is history.
My Vimeo Table Top Review of the KWC Sigma SW40F Blowback CO2 BB Pistol:
Trigger Pull: The trigger pull on the Cybergun Sig Sauer P226 Airsoft Replica is good in both single and double action. Once the slide is pulled back and released the first round is chambered and the hammer will remain back placing the P226 in single action mode, the pull is light and the take-up is fairly short, most of your shots will be in single action mode unless you use the de-cocker to lower the hammer for a subsequent double action next shot, double action shots are still pretty light but much longer in order to cock the hammer.
Accuracy: Shooting the Cybergun Sig P226 from 20 feet out in semi rested position I was able to get very good results. I placed 10 rounds in about 1.5 inches with the shot placement being a bit low possibly due to my barrel mod, adjusting the hop-up may bring the aim point back up to where it should be. The Sig Sauer P226 Airsoft Replica shot right around the 316 fps range while conducting my 5 shot average chrony testing which was lower than advertised but I was using much heavier .20 gram BB's. You can expect to get a full magazine worth of shots out of each gas fill-up but I did notice that as the magazine got colder it did tend to become much less efficient and also seemed to vent a lot of vapor.
Build Quality: The build quality is generally good and I was surprised at the finish on this model as the paint is not showing any wear marks so far, the fit is good with minimal slide and barrel wobble and everything is working very well with no problems so far with a fair amount of shots through it, guess you could say I like shooting this gun :) Most of the gun is metal with only the grips and a couple internal parts being plastic.
Realism: The Cybergun Sig Sauer P226 6mm Airsoft pistol is a replica of the real steel Sig Sauer P226 right down to the licensing and it really is a great looking and functioning Airsoft Replica. You can field strip this gun exactly like a real Sig and all the mechanical parts work just the same including a working de-cocker and adjustable front sight.
Seemed to shoot a bit low for me, could adjust with hop-up a bit?
Only one magazine per Gas fill.
Comments:
I am a big Sig Sauer fan so it would take a lot for me to not give this gun a good review, with that said it performed pretty well, sure it was not the most powerful but I was using gas over CO2 so I was not expecting too much, it also shot a bit low for me but again that may have been because of the barrel mod so who really knows for sure at this point ;) And yes it came with that unsightly orange tip that I took short work of removing. At teh end of the day I still love it and it performed well without letting me down, just like a would expect from a real Sig Sauer!
My Vimeo Table Top Review of the Cybergun Sig Sauer P226 GBB Blowback Airsoft Pistol:
I usually do my Table Top Video Review first but this time around I did my Field Test Video Review first since I was all setup checking out a couple other guns at the time. When I do my detailed Table Top Video Review for the Cybgergun Sig Suer P226, I'll post the link here so stay tuned. If you have not already checked out my Barrel Mod Video for this same gun then check that video out where I remover the extended orange portion of the metal barrel and make the barrel flush with the end of the slide which is how the real steel version was originally made.
Getting back to the Cybergun Sig Sauer P226 GBB blowback Airsoft Pistol field test, as per usual I test this Airsoft semi auto gas blowback pistol on the Chronograph to see what kind of real world velocity I get and since I had some Green Gas on hand, I used it for this part of the review and got an average of 315 fps with a six shot string.
I also stepped back 20 feet and shot 10 times at my stationary target using a semi rested position (sand bag up front and kneeling in the back). Even though the Sig Sauer P226 shot a bit low I did get about a 1.25 inch group with the exception of one flyer that hooked down just a bit making the 10 shot group a bit wider at just under 2 inches. The low shot placement may have been caused by my barrel mod but since I did not do a before and after test, I can not say for sure?
Make sure to watch my YouTube Video of this Field Test as it also includes some nice slow-motion of the slide blowback at both 400 and 1200 frames per second.
Watch my full Video Field Test Shooting Vimeo Video below:
My 5 shot Chronograph test resulted in a lower than expected 308 average fps while my accuracy test shot from 20 feet out in a semi rested position this time received a just over 2 inch group but with most shots being within 1 inch, I have found with Airsoft guns that there can be some floaters perhaps due to inconsistencies with some of the ammo. In terms of shot placement the KJWORKS KP-05 HI-CAPA 1911 shot very well centered only being just slightly high and to the left but only marginally. I was also able to get 2 full magazines plus another half mag this time around so just over 60 shots with the KP-05.
KJWorks KP-05 1911 HI-CAPA Airsoft Pistol although not shooting as hard as I though it would still performed great for me and would make a great field gun as it performs very well and has a nice high capacity magazine which would come in handy in the heat of battle.
