Entries in Blowback,Blank Gun News

Umarex T4E S&W M&P9 M2.0 .43 Cal. Paintball Pistol Field Test Review

No Comments

It’s always fun shooting a Paintball Gun like the Umarex T4E S&W M&P9 M2.0 .43 Cal. Paintball Pistol for a change but in this case it’s not all that different then shooting one of my BB or Airsoft pistols, with the acceptation of the .43 caliber rubber balls. I went with rubber balls rather than Paintballs inside my Sea Can Indoor Airguns Shooting Range to keep things clean. Actual Paintballs may have performed a little different than the rubber balls but this gives us a good idea on what the Umarex T4E S&W M&P9 M2.0 .43 Cal. Paintball Pistol is capable of

First, I put five rounds through my Chrony Chronograph to see what the real world FPS would be, keep in mind I was using rubber balls rather than paintballs and the rubber balls are a little bit heavier than paintballs so this could bring the FPS down a bit compared to the slightly lighter paintballs. Using a brand new CO2, the Umarex T4E S&W M&P9 M2.0 .43 Cal. Paintball Pistol average 315 FPS which was higher than the claimed 290 FPS! Temperature inside my Sea Can Airgun Shooting Range was around 24 degrees Celsius or 75 degrees Fahrenheit.

Moving on to my accuracy testing, as per usual I positioned myself 30 feet back from my fresh paper target and using a seated and rested shooting position I shot a full magazine (8 rounds) of rubber balls on target with the Umarex T4E S&W M&P9 M2.0 .43 Cal. Paintball Pistol. I was not expecting as tight groups as I would get using a BB or Airsoft pistol since Paintball guns are not known for super tight groups. I did manage to shoot around a 6 inch group with most of the shots staying within around 3 inches all pretty well centered. This is about what I was expecting as paintball guns are not meant for "target practicing", generally you are going to be shooting human sized objects and hoping to get some well placed center mass shots. 3-6 inch accuracy at 30 feet will get the job done for sure. I did find the trigger using rubber balls did have a bit more friction while the inner barrel seated itself into the magazine. When shooting quickly with the Umarex T4E S&W M&P9 M2.0 .43 Cal. Paintball Pistol it is much less noticeable and overal the trigger is not bad.

I know some of you are going to ask about using the Umarex T4E S&W M&P9 M2.0 .43 Cal. Paintball Pistol with rubber balls for non-lethal self defense and the reality is it will not stop a person who is determined on hurting you. There is simply not enough stoping power here. Will it a lot if you get shot up close with one of these Umarex T4E S&W M&P9 M2.0 .43 Cal. Paintball Pistols especially directly on the skin ? For sure but a well timed punch has more chance of dropping someone than a .43 caliber rubber ball moving at around 300 FPS. You may scare someone off simply by brandishing it but you take the chance of the person calling your bluff. Perhaps 8 rubber balls to the face will change their mind but that's a chance you have to figure out if you want to take or not.

The Umarex T4E S&W M&P9 M2.0 .43 Cal. Paintball Pistol is on par with the Umarex Walther PPQ M2 .43 Cal. Paintball Pistol for being about the best I have seen in terms of replica paintball guns. It is as good as they come for realism. In terms of power and accuracy I was very pleases with the results I got. Throw in some extra magazines and you have yourself a nice trainer.

Buy in the Canada Replica Airguns Store or the US Replica Airguns Store

Categories: .43 cal, Blowback, CO2, Field Test, Paintball, Pistol, Review, Semi Auto, YouTube Video Tags: Umarex, T4E, S&W M&P9 M2.0

Umarex T4E S&W M&P9 M2.0 .43 Cal. Paintball Pistol Table Top Review

1 Comment

Type: Paintball Gun.
Manufacturer: Umarex - T4E.
Model: S&W M&P9 M2.0
Materials: Metal & Polymer.
Weight: 763 grams (1.7 pounds).
Barrel: Smooth bore.
Power Source: 1x12 gram CO2.
Action: Semi-Automatic with blowback action.
Ammo Type: .43 Caliber Paintball or Rubber Ball.
Ammo Capacity: 8 Rounds.
FPS: 290.

Trigger Pull: The trigger pull on Umarex T4E S&W M&P9 M2.0 .43 Cal. Paintball Pistol feels a lot like a double action trigger mainly because when you pull the trigger the inner barrel travels backwards into the magazine which seals off the barrel form the magazine so less CO2 is wasted going it not the magazine and also placing a paintball round in the barrel. This does make the trigger a little bit longer and heavier than a single action trigger. I believe the internal hammer/striker is engaged from the blowback action.

Accuracy: So far I have not had the opportunity to test the Umarex T4E S&W M&P9 M2.0 .43 Cal. Paintball Pistol out so stay posted for my future Field Test Shooting Video where I will see what kind of fps and accuracy we can expect from the Umarex T4E S&W M&P9 M2.0 .43 Cal. Paintball Pistol. You can watch my Field Test Shooting Video for the Umarex Walther PPQ M2 .43 Cal. Paintball Pistol as it is very similar in design..

Build Quality: The build quality of the Umarex T4E S&W M&P9 M2.0 .43 Cal. Paintball Pistol is really very good, metal parts are where you would expect them, the slide, slide catch, barrel, magazine and most internal parts giving the Umarex T4E S&W M&P9 M2.0 .43 Cal. Paintball Pistol a nice near 2 pounds (1.7 pounds) of weight with the magazine in which makes the Paintball version a little heavier than the real steal version (1.54 pounds) but once the real steal version is loaded with a full mag this may even out a bit. The Umarex T4E S&W M&P9 M2.0 .43 Cal. Paintball Pistol does have a polymer frame but again this is normal with todays modern guns and helps keep the weight down. Fit and finish is also very good!

Realism: The Umarex T4E S&W M&P9 M2.0 .43 Cal. Paintball Pistol  is a near perfect replica of the real steel S&W M&P9 M2.0 Pistol, from the fully licensed markings to the large .43 caliber diameter barrel. If you placed the Paintball version side by side with the real steel version I doubt you could tell them apart unless you start inspecting it really close up and working the action. You will find that the slide cycle distance is a bit shorter than it would be meaning that when the side catch is engaged the slide does not go as far back as it the real 9mm S&W M&P9 M2.0. Field stripping the Umarex T4E S&W M&P9 M2.0 .43 Cal. Paintball Pistol will requires some tools and pin removal.

Purchase it from: The Canada Replica Airguns Store or the US Replica Airguns Store

Pros:

  • Really great weight and solid feeling gun.

  • Full Metal slide that locks back on the last shot.

  • All metal heavy full size drop out magazine adds some additional weight to the gun.

  • Very Accurate S&W M&P9 M2.0 replica, almost indistinguishable from the real still version.

  • Everything works pretty much like the real gun so a great training tool.

  • Adjustable yellow dot sights.

  • Working trigger safety.

  • Fit and finish is excellent.

  • Magazine spring release really shoots the magazine out.

  • Love the .43 caliber barrel opening, adds to realism.

Cons:

  • Trigger is a bit long as it shoots like a double action trigger, this is because the inner barrel has to travel back into the magazine before firing.

  • Magazine only holds 8 rounds, so you are going to need extra magazines for sure.

  • Blowback action is not full blowback, more like a typical half blowback BB gun.

Comments:

The Umarex T4E S&W M&P9 M2.0 .43 Cal. Paintball Pistol is mechanically very close to the Umarex Walther PPQ M2 .43 Cal. Paintball Pistol in how it functions as a Paintball Pistol so I expect both to shoot very similarly and that’s not a bad thing since the Umarex Walther PPQ M2 .43 Cal. Paintball Pistol performed rather well for me in the Replica Airguns Sea Can Indoor Shooting Range. I like that the Umarex T4E S&W M&P9 M2.0 .43 Cal. Paintball Pistol come with additional back-straps to fit any sized hands and overall I feel it would make a great training tool since the Umarex T4E S&W M&P9 M2.0 .43 Cal. Paintball Pistol as it looks, feels and functions just like a real 9mm S&W M&P9 M2.0.

Categories: .43 cal, Blowback, CO2, Comparison, Paintball, Pistol, Review, Semi Auto, YouTube Video Tags: Umarex, T4E, S&W M&P9 M2.0, S&W M&P

Umarex Glock 19X CO2 Blowback BB Pistol Field Test Review

No Comments

If you have not already checked out my Table Top Video then make sure to do so for more details and specifications and also some nice close up video of the Umarex Glock 19X CO2 Blowback BB Pistol. In this video we see how well the Umarex Glock 19X CO2 Blowback BB Pistol performs in the Replica Airguns Indoor See Can Airgun Shooting Range. I test out the velocity and accuracy and also talk a little bit about how the gun performed overall for me. You can also checkout my Table Top and Field Test Shooting Video for the Umarex Glock 17 3rd Gen as it is mechanically very similar to the Umarex Glock 19X CO2 Blowback BB Pistol.

Starting off with my velocity power test using my  Caldwell Ballistic Precision Chronograph, I was able to get really close to the factory claimed fps of 360 with an average of 347 fps. Shooting conditions where decent in the See Can compared to outside temperatures in late October but still not that warm at only 16 Degrees Celsius (60 Degrees Fahrenheit), a lot warmer than outside but still not as warm as your typical summer day. In warmer conditions I am sure I would have hit the claimed 360 or even high fps with the Umarex Glock 19X CO2 Blowback BB Pistol.

Next for my Field Testing , I placed 10 shots into a paper target with my Umarex Glock 19X CO2 Blowback BB Pistol from 30 feet down range using my standard seated and rested shooting position (Seated in the back and rested on a sand bag up front). I was able to get right around a 2 inch 10 shot group, not bad at all! The Umarex Glock 19X CO2 Blowback BB Pistol did shoot a little bit high and to the left which for some reason is common with most CO2 action airguns and I know it’s not entirely me since others have commented the their airguns shoot a bit to the left in most cases. Elevation was pretty close at 30 feet but just a tad high.

The Umarex Glock 19X CO2 Blowback BB Pistol is very similar to their Umarex Glock 17 3rd Gen in terms of their mechanical build and function since both use the same magazines and have that semi blowback action but I can say the Umarex Glock 19X CO2 Blowback BB Pistol not only looks better in my opinion but the slide is improved as it seems to have a less metallic sound and the slide wiggle is very minimal. The Umarex Glock 19X CO2 Blowback BB Pistol also did not lack in the performance department getting really close to the the claimed 360 FPS while shooting about the same 10 round grouping of 2 inches which is about what I expect for an action BB shooter. Now we have a bunch of Umarex Glocks to chooses from, checkout our Replica Airguns Canada and US Online Stores for Glock airguns and find one that’s right for you!

Categories: 4.5mm / .177 cal, BB, Blowback, CO2, Field Test, Pistol, Review, Semi Auto, YouTube Video Tags: Umarex, Umarex Glock, Glock 19X

Umarex Glock 19X CO2 Blowback BB Pistol Table Top Review

3 Comments

Type: Blowback CO2 BB Pistol.
Manufacturer: Distributed by Umarex.
Model: Glock 19X.
Materials: Metal & Polymer.
Weight: 1.5 pounds (662 grams).
Barrel: Smooth bore 3.36 inch barrel (85.3mm).
Propulsion: CO2 x 1.
Action: Semi auto blowback, double action only trigger.
Ammunition Type: 4.5mm steel BB's.
Ammunition Capacity: 18 round drop out full size metal magazine.
FPS: Claimed 360.

Trigger Pull: The trigger pull on the Umarex Glock 19X CO2 Blowback BB Pistol is what I would call a double action trigger mainly because there is an indexing of the BB from the magazine into the breach area every time you pull the trigger which means the take up is longer thanks a standard Glock take up and there is a little bit of friction from the mechanical mechanism that indexes the BB making the trigger feel more like a double action only trigger.

Accuracy: At this point I have not shot the Umarex Glock 19X CO2 Blowback BB Pistol so I can only quote what Umarex is saying in terms of FP2 which is 360. That said I have already done a full Table Top and Field Test Shooting Video for the Umarex Glock 17 Gen 3 CO2 Blowback BB Pistol which is essentially the same mechanical gun but with a slightly longer slide and barrel. In my Field Test Shooting Video for the Umarex Glock 17 Gen 3 CO2 Blowback BB Pistol I was able to get a 5 shot average fps of 363 in a bit cooler shooting conditions along with 2 inch 10 shot grouping from a 30 foot shooting distance.

Build Quality: The Umarex Glock 19X CO2 Blowback BB Pistol seems to be really well made. Fit and finish are nice and slide wiggle is minimal. There is a bit of a clanky sound when the slide cycles but not as bad as the Umarex Glock 17 Gen 3 CO2 Blowback BB Pistol. I also think the Coyote finish is the nicest looking with its black on tan two tone look.

Realism: The Umarex Glock 19X CO2 Blowback BB Pistol absolutely looks the part of a Glock 19X, sitting on the table and even holding it in your hand you are going to think it's the real deal until of course you drop the magazine and see that it is a CO2 mag. Mostly everything operates like a real Glock 17 but the slide is not a full blowback meaning it only goes back about 3/4 as much as a real Glock 17 slide would. One other noticeable difference is the ability to quickly field strip the Umarex Glock 19X CO2 Blowback BB Pistol, you will need to remove a pin since the take down tabs are non functioning and moulded into the frame.
Available From: The Replica Airguns Store.

Pros:

  • Nice weight and feel to it, build quality seems good.

  • Really nice looking replica of the real steel Glock 19X, love the Coyote color.

  • Fully Glock licensed.

  • Easy to see white dot sights front and back.

  • Recessed barrel for added realism.

  • Accessory rail for adding a laser or tactical light.

  • Full size drop out metal magazine that holds the CO2 and 18 4.5mm steel BB’s.

  • Safety built into the serial number plate area keeps it well hidden. 

  • Warning instruction are nice and discreet under trigger guard

  • Not bad feeling double action only trigger as the blowback pre-cocks the internal hammer/strike.

  • 360 fps is decent for a blowback BB gun.

Cons:

  • Does have blowback action but not full blowback.

  • Slide sound is a bit clanky but not as bad as the 17 Gen 3 Blowback.

  • Sight are non-adjustable which is common with low cost action shooters like this one.

  • Would have liked to have seen more pristine packaging from Glock over the plastic clamshell

Comments:

It’s great to see Umarex expanding their live of Glock licensed Airguns and the addition of the Umarex Glock 19X CO2 Blowback BB Pistol is welcome! Some of you are not going to like the semi blowback action but it does mean you get higher fps and more shots per CO2 while still getting that simulated recoil form the blowback action. I honestly thing the Umarex Glock 19X CO2 Blowback BB Pistol is one of the most attractive Glock Airguns with it’s Coyote Tan frame and slide with black highlights, I also like the compact size for its shortened frame and slide over the Umarex Glock 17 Gen 3 CO2 Blowback BB Pistol. So many to choose for now but I guess that a good thing or perhaps just get them all!

Categories: 4.5mm / .177 cal, BB, Blowback, CO2, Comparison, Pistol, Review, Semi Auto, YouTube Video Tags: Umarex, Umarex Glock, Glock 19, Glock 19X

2019 Replica Airguns Halloween Contest Giveaway

No Comments

There are two parts to they video, the Halloween Costume Contest and what’s going on next week so make sure to watch it all…

Part 1 - 2019 Replica Airguns Halloween Contest Giveaway

Contest Rules:

  • Must be 18+ to receive a prize.

  • Canada & US winners only.

  • Halloween Costumes must have a weapon of some sort in them.

  • Must post a Halloween costume video to your YouTube channel.

  • Your video must be named "2019 Replica Airguns Halloween Contest Giveaway".

  • November 9th is the deadline date for you to get your video in.

  • Must post a comment in this video letting me know you have a video for me.

  • Must be a subscriber to the Replica Airguns channel.

  • Must like this video

1st, 2nd and 3rd Prizes Awarded:

What’s going on next week?

I will be away competing in a Body Building Fitness Contest so there will not be any more videos that week.

You may have noticed I have been withering away this past couple of months. This is in preparation for a Fitness Contest I am going into. For a show like this you need to be super lean to be competitive.

I have been competing since 2015 mainly in Men’s Physique and have qualified myself over the years to compete at the National level in Amateur Body Building.

The competition I am going to is the GNC / ALLMAX Canadian National Pro Qualifier in Toronto. If I do really well I can possibly get an IFBB Pro Card. Getting an IFBB Pro Card means I would now be able to compete in Pro Body Building competitions.

In order to win the Pro Card I would need to win my hight class and then win the overalls against the other winners in their hight class.

To date I have come close to winning the IFFB Pro Card but just missed it on two occasions. I am hoping to get the IFBB Pro Card this times around but I know the competition will be very competitive.

Categories: 4.5mm / .177 cal, 6mm, Airsoft, BB, Blowback, CO2, Full Auto, Replica Airguns News, Semi Auto, Pistol, Rifle, YouTube Video Tags: Crosman, Bushmaster MPW, KWC, Taurus PT24 24/7, Umarex, Makarov PM, Makarov

Tokyo Marui FNX-45 Tactical GBB Airsoft Pistol TableTop Review

1 Comment

Type: GBB Airsoft Pistol.
Manufacturer: Made by Tokyo Marui.
Model: FNX-45 Tactical.
Materials: Mostly polymer with metal components.
Weight: 1.8 pounds (830 grams).
Barrel: 4.4 inches metal non-rifled.
Propulsion: Green gas.
Action: Semi auto blowback, singled double action trigger.
Ammunition Type: 6mm plastic Airsoft BB's.
Ammunition Capacity: 29 round drop out full size metal magazine.
FPS: Claimed 366.

Trigger Pull: The single action trigger pull on the Tokyo Marui FNX-45 Tactical GBB Airsoft Pistol is light and smooth with just a bit of take-up and a crisp release. You can also shoot in double action, as expected the trigger pull in double action will be longer and heavier but it’s still pretty smooth and not at all heavy.

Accuracy: At this point I have not shot the Tokyo Marui FNX-45 Tactical GBB Airsoft Pistol so I have no idea what the actual fps is and how accurate it may be but I can say I like the feel of how it dry fires so if that’s any indication as to how well it performs then I have high hopes for the Tokyo Marui FNX-45 Tactical GBB Airsoft Pistol.

Build Quality: The Tokyo Marui FNX-45 Tactical GBB Airsoft Pistol even though on the outside it’s all plastic (Slide and frame), the quality is fantastic, fit and finish is top notch everywhere and you will find metal parts where they need to be as in the inner and outer barrel, trigger, hammer, slide catch release, back strap safety, trigger group and many more internal parts.

Realism: The Tokyo Marui FNX-45 Tactical GBB Airsoft Pistol is virtually an exact replica of a Real Steel FNX-45 Tactical, looking at photos online of the powder burning version it is nearly impossible to tell them apart. You will find FN licensing in all the right places but keep in mind Tokyo Marui does not actually hold an FN license so yours will come with black stickers over the FN markings. Easy enough to take off :) In terms of functionality the Tokyo Marui FNX-45 Tactical GBB Airsoft Pistol operated pretty much exactly like the real steel version including the ability to field strip it for easy Hop-up adjustments.

Pros:

  • Ultra realistic Replica of the FNX-45 with authentic markings.

  • Removable slide cover allows mounting of red dot sight.

  • 16mm CW threaded barrel is mock suppressor-ready.

  • Multiple grip backstraps for a custom fit to your hand size.

  • Overall quality, fit and finish is excellent.

  • Easy to see white dot sights front and back.

  • Full size full metal magazine.

  • Ambidextrous safety, slide catch and magazine release.

  • Can easily put a mock suppressor on it.

  • Comes with additional internal barrel lengths for a mock suppressor or no meat tenderizer setup.

  • All mechanical parts work just like a steel FNX-45.

  • Super fast blowback action, great for action shooting.

Cons:

  • Mostly all plastic build.

  • Not actually licensed by Tokyo Marui.

Comments:

I am really liking the Tokyo Marui product line and welcome it to our Canada Replica Airguns Store. The Tokyo Marui FNX-45 Tactical GBB Airsoft Pistol is one the nicest quality Airsoft guns I have reviewed so far, it really is a work of art. The only thing that would be nice is a metal slide but I can live without it since everything else about the gun is nearly perfect! The Tokyo Marui FNX-45 Tactical GBB Airsoft Pistol is really built for everyone, left hand or right handed, large or small hands, the full set of ambidextrous controls and interchangeable back-straps will take care of you.

Categories: 6mm, Airsoft, Blowback, Gas, GBB, Pistol, Review, Semi Auto, YouTube Video Tags: Tokyo Marui, FNX-45 Tactical

Tokyo Marui Strike Warrior .45 1911 GBB Airsoft Pistol Table Top Review

No Comments

Type: GBB Airsoft Pistol.
Manufacturer: Made by Tokyo Marui.
Model: Marui Strike Warrior .45 1911.
Materials: Mostly polymer with metal components.
Weight: 1.8 pounds (816 grams).
Barrel: 3.9 inches metal non-rifled.
Propulsion: Green gas.
Action: Semi auto blowback, single action only trigger.
Ammunition Type: 6mm plastic Airsoft BB's.
Ammunition Capacity: 28 round drop out full size metal magazine.
FPS: Claimed 366.

Trigger Pull: The single action only trigger pull on the Tokyo Marui Strike Warrior .45 1911 GBB Airsoft Pistol is extremely nice, there is virtually zero take-up with a light and easy release. You can really hammer out quick shots with this Airsoft pistol. One of the best 1911 triggers I have tested so far.

Accuracy: At this point I have not shot the Tokyo Marui Strike Warrior .45 1911 GBB Airsoft Pistol so I have no idea what the actual fps is and how accurate it may be but I can say I like the feel of how it dry fires so if that’s any indication as to how well it performs then I have high hopes for the Tokyo Marui Strike Warrior .45 1911 GBB Airsoft Pistol.

Build Quality: The Tokyo Marui Strike Warrior .45 1911 GBB Airsoft Pistol even though on the outside it’s all plastic (Slide and frame), the quality is fantastic, fit and finish is top notch everywhere and you will find metal parts where they need to be as in the inner and outer barrel, trigger, hammer, slide catch release, back strap safety, trigger group and many more internal parts.

Realism: The Tokyo Marui Strike Warrior .45 1911 GBB Airsoft Pistol is built on the Colt 45 1911 design but as you can see it comes in a compact version with a very tactical and aggressive look. You can tone it down a bit by removing the “Meat Tenderize” from the front basically turning it into a straight forward Tactical 1911 Compact version.

Pros:

  • Custom Detonics style slide and outer barrel.

  • Meat tenderizer-like Strike Face muzzle gives gun aggressive appearance.

  • 20mm underside rail for laser or flashlight attachment.

  • Squared-off SAO trigger guard with short-stroke trigger pull.

  • Fit and finish is excellent.

  • Easy to see white dot sights front and back.

  • Full size full metal magazine.

  • Very cool looking tactical compact 1911.

  • Ambidextrous safety.

  • Comes with additional internal barrel lengths for a Mock suppressor or no Meat tenderizer setup.

  • Working grip safety as you would expect.

  • All mechanical parts work just like a real steel 1911.

  • Super fast blowback action, great for action shooting.

Cons:

  • Mostly all plastic build.

  • Can not field strip easily and get to the hop-up adjustment with the Meat tenderizer on it.

Comments:

This is my first real experience with a Tokyo Marui product and I have to say I am very impressed with their build quality and design. Even though the slide and frame are plastic, there is enough metal going on in this Airsoft pistol to give it decent enough weight and feel. I really like what Tokyo Marui did with the styling of the Tokyo Marui Strike Warrior .45 1911 GBB Airsoft Pistol with the Meat tenderizer-like Strike Face muzzle, squared-off trigger guard and overall tactical look and feel. A great addition to the Replica Airguns Canada Online Store!

Categories: 6mm, Airsoft, Blowback, Gas, GBB, Pistol, Review, Semi Auto, YouTube Video Tags: Tokyo Marui, Strike Warrior .45

Tokyo Marui New Product Preview Unboxing Video

No Comments

TokyoMaruiLogo.jpg

I though I would feature the fact that we recently added some of the Tokyo Marui product line to our Canada Replica Airguns Store. Tokyo Marui is said to be one of the best Airsoft products on the market and they have been around for a while so they have had time to get it right! As Tokyo Marui is a Japanese based company they are restricted to only being able to use plastic frames and slides but even with this limitation the Tokyo Marui products that I have personally looked at are extremely well made.

In this Tokyo Marui New Product Preview Unboxing Video I take a look at 4 Tokyo Marui models; the Tokyo Marui Strike Warrior .45 1911 Gas Blowback Airsoft Pistol, the Tokyo Marui Hi-Capa 5.1 D.O.R (Direct Optics Ready) GBB Airsoft Pistol, the Tokyo Marui FNX-45 Tactical Gas Blowback Airsoft Pistol and lastly the Tokyo Marui VSR-10 Pro Sniper Bolt Action Airsoft Rifle.

Tokyo Marui Strike Warrior .45 1911 Gas Blowback Airsoft Pistol

  • Type: Airsoft Pistol

  • Manufacturer: Tokyo Marui

  • Model: Strike Warrior .45

  • Materials: ABS

  • Weight: 816 g (1.8 lb)

  • Length: 205 mm (8.1 in)

  • Barrel: 74 mm (2.9 in), metal

  • Power Source: Green Gas

  • Action: Semi-automatic, blowback

  • Ammo Type: 6mm airsoft BBs

  • Ammo Capacity: 28 rounds

  • FPS: 366

Tokyo Marui Hi-Capa 5.1 D.O.R (Direct Optics Ready) GBB Airsoft Pistol

  • Type: Airsoft Pistol

  • Manufacturer: Tokyo Marui

  • Model: Hi-Capa 5.1 D.O.R.

  • Materials: Polymer and metal

  • Weight: 839 g (1.85 lb)

  • Length: 220 mm (8.7 in)

  • Barrel: 112 mm (4.4 in), metal

  • Power Source: Green Gas

  • Action: Semi-automatic, blowback

  • Ammo Type: 6mm airsoft BBs

  • Ammo Capacity: 31 rounds

  • FPS: 366

Tokyo Marui FNX-45 Tactical Gas Blowback Airsoft Pistol

  • Type: Airsoft Pistol

  • Manufacturer: Tokyo Marui

  • Model: FNX-45 Tactical

  • Materials: ABS

  • Weight: 830 g (1.8 lb)

  • Length: 220 mm (8.7 in)

  • Barrel: 113 mm (4.4 in)

  • Power Source: Green Gas

  • Action: Semi-automatic, blowback, single/double-action

  • Ammo Type: 6mm airsoft BBs

  • Ammo Capacity: 29 rounds

  • FPS: 366

Tokyo Marui VSR-10 Pro Sniper Bolt Action Airsoft Rifle

  • Type: Airsoft Rifle

  • Manufacturer: Tokyo Marui

  • Model: VSR-10 Pro Sniper vers.

  • Materials: ABS

  • Weight: 1.9 kg (4.2 lb)

  • Length: 107.5 cm (42.3 in)

  • Barrel: 430 mm (17 in)

  • Power Source: Spring

  • Action: Bolt action

  • Ammo Type: 6mm airsoft BBs

  • Ammo Capacity: 30 rounds

  • FPS: 366

Categories: 6mm, Airsoft, Blowback, Comparison, GBB, Gas, Pistol, Review, Replica Airguns News, Rifle, Semi Auto, Spring Piston, YouTube Video Tags: Tokyo Marui, VSR-10 Pro, FNX-45 Tactical, Hi-Capa 5.1 D.O.R., Strike Warrior .45

Umarex T4E HK 416 Training Marker CO2 Paintball Rifle Field Test Review

No Comments

If you have not already watched my Table Top Video Review for the Umarex T4E HK 416 Training Marker CO2 Paintball Rifle than make sure to do so if you are interested in more specifications and details.

I don’t often make many Paintball Review Gun Videos let alone Shooting Videos so this one is a bit different than the norm. Lucky for me I have some .43 caliber Rubber Paintballs that I can use in my Indoor Sea Can Shooting Range so as not to make a mess of things. As per usual I like to use a brand new 12 Gram CO2 Cartridge for my testing and for your reference the temperature was right around room temperature or 21 degree Celsius, 69 degrees Fahrenheit.

First up I generally perform my Chronograph test to see what the real world velocity or fps is for the Umarex T4E HK 416 Training Marker CO2 Paintball Rifle. I shot a short string of rubber rounds through my Chronograph and was able to get a 280 fps average with the Umarex T4E HK 416 Training Marker CO2 Paintball Rifle. This is plenty enough power for the intended target down range to feel the paintball effect without causing too much trauma.

With the remaining 10 rounds in my Umarex T4E HK 416 Training Marker CO2 Paintball Rifle magazine, I then setup a brand new paper target 30 feet down range and using a rested and seated shooting position and carefully unloaded the Umarex T4E HK 416 Training Marker CO2 Paintball Rifle into the target. I was a bit surprised to see the rounds spread out a fair amount perhaps as much as 10-12 inches but at least half where in the target rings.

I would not recommend the Umarex T4E HK 416 Training Marker CO2 Paintball Rifle as a long range paintball marker but it would be perfect for close quarters ultra realistic simulations. I would like to give actual .43 caliber paintballs a try outside to see if accuracy would be better, maybe the rubber balls grip the barrel a bit too much causing some random and unexpected spinning to occur? Either way the Umarex T4E HK 416 Training Marker CO2 Paintball Rifle is a really unique and fun Paintball Gun to shoot, maybe not for everyone but if you want the most realistic Paintball Marker then it would be a great option.

Categories: .43 cal, Blowback, CO2, Field Test, Paintball, Review, Rifle, Semi Auto, YouTube Video Tags: Umarex, T4E HK416

Umarex T4E T4E HK 416 Training Marker CO2 Paintball Rifle Table Top Review

No Comments

Type: Paintball Rifle.
Manufacturer: Umarex - T4E.
Model: H&K 416.
Materials: Metal & Polymer.
Weight: 3016 grams (6.65 pounds).
Barrel: Metal smooth bore.
Power Source: 1x12 gram CO2.
Action: Semi-Automatic with internal working bolt blowback action.
Ammo Type: .43 Caliber Paintball or Rubber Ball.
Ammo Capacity: 14 Rounds.
FPS: 330-460?

Trigger Pull: The trigger pull on Umarex T4E T4E HK 416 Training Marker CO2 Paintball Rifle is pretty typical of what you would find on an AR styled rifle. Since the internal bolt cycles with each shot, the trigger is engaged and the Paintball rifle is ready for the next shot with a very light and short single action trigger pull.

Accuracy: So far I have not had the opportunity to test the Umarex T4E T4E HK 416 Training Marker CO2 Paintball Rifle other than placing a few rounds down range into my ammo trap to see how it shot and felt. Without actually shooting rounds through the Chronograph I don’t really know what the fps velocity is going to be but I can say it felt like it was shooting perhaps even over 400 fps? Out of the box the Umarex T4E T4E HK 416 Training Marker CO2 Paintball Rifle was shooting rather low but you can adjust the rear sight for windage and elevation.

Build Quality: The build quality of the Umarex T4E T4E HK 416 Training Marker CO2 Paintball Rifle is very good since this Paintball gun is made for military and law enforcement training use. You’re going to find high quality metal and polymer where you would normally find them on the real steel version. The bolt carrier is expected to last at least 3000 shots but you do get an extra one included with it.

Realism: The fully licensed Umarex T4E T4E HK 416 Training Marker CO2 Paintball Rifle is about as realistic as you are going to get in a Paintball Rifle. It’s basically made very similar to a GBB Airsoft Rifle of the same type with a working bolt and pretty much all working parts on it. You can even break the Umarex T4E T4E HK 416 Training Marker CO2 Paintball Rifle down into the lower and upper receiver halves. The bolt blowback action is not super strong but this may be a good thing since CO2 usage will be more efficient allowing for higher fps and more shots per CO2.

Purchase it from the Canada Replica Airguns Store or the US Replica Airguns Store

Pros:

  • Seem to have decent fps, will see when I do my Field Test?

  • Full Size drop out magazine that holds 14 .43 caliber Paintballs and the CO2.

  • Removable 4 position adjustable stock.

  • Removable and adjustable iron sights.

  • Lots of rials for adding accessories.

  • Fully licensed H&K 4116 replica via Umarex.

  • Blowback does give a bit of recoil feedback and allow for a true single action trigger.

  • Very high quality metaled polymer build.

  • Used as a training weapon for military and law enforcement.

  • Comes with extra bolt carrier.

Cons:

  • Very expensive, well over $1000!!

  • Comes with blue hardware but can be swapped out (Pistol grip, But stock, Magazine).

  • Bolt carrier may wear out at around 3000 rounds.

Comments:

If’ you’re looking for the ultimate in Paintball Rifle realism the Umarex T4E T4E HK 416 Training Marker CO2 Paintball Rifle is going to meet that requirement for sure. It will come at a pretty decent cost but you are going to have a very unique Airgun that not many people will own. And as they say you do get what you pay for which is realism, quality and reliability. I look forward to testing out the Umarex T4E T4E HK 416 Training Marker CO2 Paintball Rifle on the Chronograph using some rubber ball ammo, I may even take it outside for some paintball ammo shooting, we will have to see…

Categories: .43 cal, Blowback, CO2, Paintball, Review, Rifle, Semi Auto, YouTube Video Tags: T4E HK416, Umarex

Umarex Glock 17 4th Gen CO2 Blowback BB Pistol Field Test Review

No Comments

In this Field Test Shooting Video I focus on Umarex’s latest CO2 Blowback BB Airgun, the Umarex Glock 17 4th Gen CO2 Blowback BB Pistol. We have been waiting a while for this one to ship and now that it’s here I really want to get to shooting it and finding out if it performed as good as it looked and felt.

I loaded up my Umarex Glock 17 4th Gen CO2 Blowback BB Pistol with a brand new 12 gram Sig Sauer CO2 cartridges along with some 4.5mm RWS 5.1 grain Zinc coated BB’s and began the Chronograph portion of my Indoor Field Test Shooting Video. The temperature was not overly warm sitting right around 19 degrees Celsius or 66 degrees Fahrenheit. Umarex claims roughly around 300 fps from the Umarex Glock 17 4th Gen CO2 Blowback BB Pistol but I was able to get just a bit high with my 5 shots through the Chronograph averaging 310 fps.

I then put up a paper target 30 feet down range, reloaded my full size drop out metal magazine with 10 more steel BB’s and proceeded to carefully place the 10 shots into the target using a rested and seated shooting position. I was able to get around a 3.5 inch grouping but I feel I could have done better since several rounds actually shot one on top of the other. The Umarex Glock 17 4th Gen CO2 Blowback BB Pistol did shot just a little bit low and to the left but not a lot.

I really like the trigger on the Umarex Glock 17 4th Gen CO2 Blowback BB Pistol, it’s short and light, perfect for shot placement and also action shooting. The blowback action is nice and crisp giving the Umarex Glock 17 4th Gen CO2 Blowback BB Pistol just enough blowback recoil effect. I didn't have any issues with the Umarex Glock 17 4th Gen CO2 Blowback BB Pistol which makes for the best testing and out of all the Umarex Glocks to date the Umarex Glock 17 4th Gen CO2 Blowback BB Pistol is by far my favorite version! If you already have and Umarex Glock, that’s OK get this one too, you won’t be disappointed.

Categories: 4.5mm / .177 cal, BB, Blowback, CO2, Field Test, Pistol, Review, Semi Auto, YouTube Video Tags: Umarex Glock, Umarex, Glock 19, Gen 4

Umarex Glock 17 4th Gen CO2 Blowback BB Pistol Table Top Review

10 Comments

Type: Blowback CO2 BB Pistol.
Manufacturer: Distributed by Umarex.
Model: Glock 17 Gen 4.
Materials: Metal & Polymer.
Weight: 1.7 pounds (771 grams).
Barrel: 3.6 inches metal non-rifled.
Propulsion: CO2 x 1.
Action: Semi auto blowback, single action only trigger.
Ammunition Type: 4.5mm steel BB's.
Ammunition Capacity: 18 round drop out full size metal magazine.
FPS: Claimed 300.

Trigger Pull: The trigger pull on the Umarex Glock 17 Gen 4 CO2 Blowback BB Pistol is single action only so you will need to rack the slide first to not only chamber a 4.5mm Steel BB in the breach area but to also cock the internal striker. There is a working trigger safety on the Umarex Glock 17 Gen 4 CO2 Blowback BB Pistol and you’ll also find the Glock 17 Gen 4 has a nice short and light trigger as you would expect similar to the real steel Glock. Perfect for fast action shooting!

Accuracy: At this point I have not shot the Umarex Glock 17 Gen 4 CO2 Blowback BB Pistol so I can only quote what Umarex is saying in terms of FP2 which is 300. That sounds reasonable based on other Airguns like this that have that full blowback action since much of the CO2 gas is used to work the action of the slide. This not only reduces how many shots you can expect o get out of a single 12 gram CO2 cartridge but a reduction in power over non-blowback or even partial blowback CO2 Airguns.

Build Quality: The Umarex Glock 17 Gen 4 CO2 Blowback BB Pistol looks to be well made overall with metal and plastic parts where you would find them on a real steel Glock 17 Gen 4. Fit and finish are nice and the slide wiggle is next to zero. The slide spring is very heavy and the sound of the slide when racked and released does not have that cheap metallic sound some blowback Airguns have. I am expecting some pretty decent blowback action recoil from the Umarex Glock 17 Gen 4 CO2 Blowback BB Pistol when I do my Field Test Shooting Review!

Realism: The Umarex Glock 17 Gen 4 CO2 Blowback BB Pistol 100% looks the part of a Glock 17 4th Generation, sitting on the table and even holding it in your hand you are going to think it's the real deal until of course you drop the magazine and see that it is a BB/CO2 mag. Mostly everything operates like a real Glock 17 including the slide catch release, trigger safety, magazine release and even the take down switches for quick field stripping and access to the adjustable hop-up, yes it is adjustable.
Available From: The Replica Airguns Store.

Pros:

  • Good weight and feel to it, build quality seems very good.

  • Really nice looking and full featured replica of the original Glock 17 Gen 4.

  • Fully Glock licensed through Umarex.

  • Easy to see white dot sights front and back.

  • Recessed barrel for added realism.

  • Accessory rail for adding a laser or tactical light.

  • Full size drop out metal magazine that holds the CO2 and 18 4.5mm steel BB’s.

  • Slide spring feels heavier than most full blowback Airguns, should have a heavy blowback recoil effect.

  • Safety built into the serial number plate area keeps it well hidden.

  • Comes with additional Backstraps for different sized hands.

  • Warning instruction are nice and discreet under trigger guard.

  • Great feeling single action only trigger as the blowback pre-cocks the internal hammer/strike.

  • 300 fps is decent for a full blowback BB gun.

Cons:

  • FPS could be higher but fairly inline with other full blowback CO2 air pistols.

  • Sight are non-adjustable which is common with low cost Airguns like this one.

  • Would have liked to have seen more pristine packaging from Glock..

Comments:

I know everyone has been waiting for Umarex to release the Umarex Glock 17 Gen 4 CO2 Blowback BB Pistol and here it is finally, does it live up to all the hype and excitement? So far without shooting it I have to say yes, I am very pleased with how the Umarex Glock 17 Gen 4 CO2 Blowback BB Pistol looks and feels. There is not too much more you can ask for in a replica Airgun of any kind… it looks like the real steel version, it feels like there real steel version, it functions like there real steel version. Hopefully it shoots just as well! If you haven’t bought one of the Umarex Glocks so far then this one is the one to have, but I say why not have them all :)

Categories: 4.5mm / .177 cal, BB, Blowback, CO2, Comparison, Pistol, Review, Semi Auto, YouTube Video Tags: Glock 17, Glock, Umarex Glock, Umarex, Gen 4

G&G GPM1911 GBB Airsoft Pistol Field Test Review

No Comments

I’m going to start off by saying this Field Test Shooting Review for the G&G GPM1911 GBB Airsoft Pistol did not go all that well as I had some complications with this Airgun when chambering rounds. I am pretty sure it is magazine related and hope to try a different magazine with it soon. I say this because I am following through with my review regardless of my initial results to demonstrate that not all Airguns perform as expected during my reviews and sometimes you get a lemon even with a good quality brand like G&G.

I am fairly certain the defect in this case for the G&G GPM1911 GBB Airsoft Pistol was the magazine tip being too tight and not allowing an Airsoft BB to position all the way to the top of the magazine which means when the slide cycled and the nozzle was in position to push an Airsoft BB into the breach, it simple was hitting the top of the BB and pushing it even further into the magazine. All said and done I was able to test the fps and accuracy on target so let’s get on with my review.

Using .20 gram Airsoft BB’s with a fully filled propane gas magazine in my G&G GPM1911 GBB Airsoft Pistol, I was able to get 6 recoreded shots through my Chronograph averaging 319 fps. The slowest shot being 313 fps and the fastest shot hitting 330 fps. The temperature was right around room temperature so around 22 degrees Celsius or 72 degrees Fahrenheit.

As I was having issues with with the G&G GPM1911 GBB Airsoft Pistol chambering rounds with the .20 gram Airsoft BB’s. I was hoping that when I switched to a different .32 gram Airsoft BB for my target portion of this review that perhaps the different Airsoft BB’s would chamber better but they did not. To get through the target portion of my test, with each shot I had to drop the magazine, make sure the Airsoft BB’s was at the top of the magazine, rack the slide, insert the magazine and then release the slide. So as you can see I was resetting completely for each shot which does not always make for the tightest groupings. Surprisingly I was still able to get about a 1.5 inch grouping on my paper target setup 30 feet downrange using a rested and seated shooting position.

Not all reviews go as planned but you still have to make the best of it. I really feel the G&G GPM1911 GBB Airsoft Pistol is a good gun overall even though mine did not perform that well for me. When I was able to chamber a round it shot a consistent fps and placed Airsoft BB’s downrange accurately and very close to the bullseye. Perhaps simply by swapping out the magazine I will have a much more reliable Airsoft gun? I will have to get back to you on that one.

Categories: 6mm, Airsoft, Blowback, Field Test, Gas, GBB, Pistol, Review, Semi Auto, YouTube Video Tags: G&G, GPM1911, 1911, M1911 A1

G&G GPM1911 GBB Airsoft Pistol Table Top Review

2 Comments

Type: Gas Blowback Airsoft Pistol.
Manufacturer: G&G
Model: GPM1911
Materials: Metal slide, frame & Magazine.
Weight: 2.25 pounds (1020 grams).
Length: 8.66 inches (22.0 cm) total.
Barrel: 4.58 inches (11.7 cm), Metal non-rifled smooth bore.
Propulsion: Green gas or propane.
Action: Blowback, single action only.
Ammunition Type: 6mm plastic Airsoft BB's.
Ammunition Capacity: 25 rounds.
FPS: 300-330 fps.

Trigger Pull: The single action only trigger pull on the G&G GPM1911 GBB Airsoft Pistol is what you would expect from a traditional single action only 1911 trigger, a very short take-up and a crips and light release. Great for getting a lot fo shoots off quickly and accurately down range without making your trigger finger do a lot of work.

Accuracy: I have not done my actual Field Test Shooting video review for the G&G GPM1911 GBB Airsoft Pistol so I can into comment just yet but I will be making a Field Test Shooting Video for it as soon as I can and will post that here on the website and of course over on the Replica Airguns YouTube channel when I have it ready.

Build Quality: The G&G GPM1911 GBB Airsoft Pistol is in my opinion one for the nicer looking finishes wise and I would have to say it seems to also be one of the better quality 1911 Airguns out there, for sure a step up from a KWC blowback 1911’s and in line with what KWA and KJWorks is making these days which is good quality. The G&G GPM1911 GBB Airsoft Pistol is one of the heavier Airsoft 1911 Blowback Pistols which makes me think the metal is a bit higher quality where it needs to be. Tolerances are nice and tight and the blowbacks action is very heavy.

Realism: The G&G GPM1911 GBB Airsoft Pistol like most of these full blowback 1911 Airguns, Steel BB or Airsoft BB, is super realistic with an all metal build. All the real steel working parts like the slide catch release, back strap safety and pretty much everything else function as they should. The G&G GPM1911 GBB Airsoft Pistol even field strips like a traditional 1911 pistol. Not sure what you could do to make it more authentic for an Airgun?

Available in the: Replica Airguns Store

Pros:

  • Nice high capacity magazine compared to other GBB 1911 Airsoft pistols.

  • Heavier than most Airsoft 1911’s.

  • All parts fit nice and tight, tolerances are very good.

  • Working back-strap safety.

  • No ugly red tip.

  • Finish is really nice, gun looks really good.

  • Expect to get decent amount of shots per gas fill.

  • Micro Gas Filter and Whirl Cylinder Valve help to manage gas efficiency and reduced frost buildup.

  • Traditional adjustable Hop-up.

  • Full Size Dropout metal magazine pretty standard on Airsoft pistols.

  • Comes with high quality hard shell case and speed loader.

Cons:

  • Sights are pretty basic, no white dots and non-adjustable as you would expect on a 1911 A1.

  • Very simple Airsoft gun, no modern bits and pieces on it.

  • FPS could be a bit higher but fine for close quarters.

Comments:

The G&G GPM1911 GBB Airsoft Pistol is for sure one of the nicer 1911 A1 styled Airsoft pistols, inline with KWC and KJWorks. It does come in a little bit heavier and seems to have more blowback recoil action which is nice. All I need to do now is find out how well it shoots! If it’s not half bad then it is for sure worth the price which by the way is a little bit cheaper than a KWA or KJWorks 1911 and about the same price as a KWC 1911. So many choices I know but that’s a good thing :)

My Table Top Review of the G&G GPM1911 GBB Airsoft Pistol:

Categories: 6mm, Airsoft, Blowback, Comparison, Gas, GBB, Pistol, Review, Semi Auto, YouTube Video Tags: G&G, GPM1911

Air Venturi Springfield Armory 1911 CO2 Blowback BB Pistol Table Top Review

2 Comments

Type: BB air pistol.
Manufacturer: Air Venturi - KWC.
Model: Springfield Armory 1911 Mil-Spec.
Materials: Pretty much all metal build.
Weight: 2 pounds (907 Grams).
Barrel: 4.38 inchesBrass, non-rifled.
Propulsion: CO2 x1.
Action: Semi auto blowback, single action only.
Ammunition Type: 4.5mm Steel BB's.
Ammunition Capacity: 18 rounds.
FPS: 320.

Trigger Pull: The trigger pull on the Air Venturi Springfield Armory 1911 CO2 Blowback BB Pistol is like all the other KWC made CO2 full blowback 1911's, it's exactly what you would expect from a real steel 1911 single action only pistol which helps to make this replica 1911 a great trainer or show piece. So in other words the trigger pull is super short, super light with very little take-up and a nice crisp break.

Accuracy: I have not shot this "exact version" of the KWC Air Venturi 1911 but it will undoubtedly perform very much like all the other incarnations. I can expect decent under 2 inch groupings from 30 feet out and will get a little over 300 fps on a full CO2 cartridges as long as it’s decently warm out. Depending on how fast I shoot off my magazines, I should expect to get around 3 good mags and if I slow things down a bit I should get a forth magazine so anywhere from 50-70 good or so shots per CO2 out of the Air Venturi Springfield Armory 1911 CO2 Blowback BB Pistol. I may or may not make a Field Test Shooting Video for the Air Venturi Springfield Armory 1911 CO2 Blowback BB Pistol…

Build Quality: Very good, with almost all metal construction, good weight and craftsmanship, the KWC 1911 line of pistols have proven themselves over time, that said they will not last forever since these are not expensive guns made out of high quality metals. You will find most of these KWC pistols in general have a rather thin coating for a finish and so they tend to wear a bit on the high spots but over time this has been improving with KWC made Airguns.

Realism: This is as close as you can come to the look, weight, feel, and action of the real 1911 in virtually almost every way including the ability to field strip this pistol exactly the same! All the mechanical parts work just like they do on a real steel 1911 including the grip safety. On top of all of this Air Venturi has licensed the Air Venturi Springfield Armory 1911 CO2 Blowback BB Pistol with very realistic Springfield branding thought the Airgun.

Available at the: Replica Airguns Store

Pros:

  • All metal construction - Good weight and solid feeling gun.

  • Heavy blowback action with that 1911 sluggish feel.

  • Very Accurate 1911 A1 styled replica in pretty much every way.

  • True 1911 Single action trigger, excellent pull, very smooth and light.

  • Working backstop safety

  • 3 dot white sights help with target acquisition on darker backgrounds.

  • Could mix and match other KWC 1911 parts.

  • Springfield Armory licensed by Air Venturi.

  • Good accuracy, not too bad amount of shots for this style of gun about 3 good magazines.

Cons:

  • Non adjustable sights.

  • Sacrifice fps and shots per CO2 because of the heavy blowback action but worth it.

  • Not  Available at time of video.

Comments:

I really never get tired of making reviews for the KWC 1911 line of CO2 Blowback Airguns, sure they are all made from the same base KWC 1911 Aigun but each one has its own unique look and customization to it. I really like the Faux plastic wood grips with the deep Springfield Armory licensing on this version. And the matt black slide and frame with the chrome barrel and silver barrel bushing really look sharp on this 1911 BB Gun. Even though the Air Venturi Springfield Armory 1911 CO2 Blowback BB Pistol is basically a standard 1911 A1, the added touch of the White Dot sights will for sure help when shooting this Blowback BB Gun at what ever target you point it at.

My Videos for the Air Venturi Springfield Armory 1911 CO2 Blowback BB Pistol:

Categories: 4.5mm / .177 cal, BB, Blowback, CO2, Pistol, Review, Semi Auto, YouTube Video Tags: AirVenturi, M1911, Colt, Springfield Armory, 1911

Webley Nemesis and G&G GPM1911 Unboxing Preview Video

No Comments

I keep getting more and more really cool airguns to review and it’s been hard to keep up with them all and get out Table Top and Field Test videos for each new product. I at least want to be able to get the word out so to speak for some of the new Airguns that come across my tassel even if I may not be able to get to their full reviews right away.

That said I have two new Airguns that we have in our Replica Airguns Stores to show everyone, the Webley Nemesis in .177 Caliber Pellet and the G&G GPM1911 GBB Airsoft Pistol. Both could not be any more different for sure but I really like each of them for their own reasons.

The Webley Nemesis is a very unique CO2 powered pistols since it is bolt action like many of the corpsman pistols but the Webley Nemesis .177 Caliber Pellet Pistol comes with a duel sided rotary magazine that holds 7 rounds on each side, the .22 caliber version holds 6 rounds on each side. The .177 caliber version can shoot up to 450 fps while the .22 caliber version has a claimed fps of up to 370. I look forward to testing and reviewing the Webley Nemesis .177 Caliber Pellet Pistol as soon as I can.

I also showcase the G&G GPM1911 GBB Airsoft Pistol which is a well priced basic A1 styled 1911 that is really well built and about one of the heaviest full metal 1911’s I have come across to date hitting the scale at nearly 2 pounds and 4 ounces. Another Replica Airgun I look forward to treating out!

Categories: .22 cal, 4.5mm / .177 cal, 6mm, Airsoft, Blowback, CO2, GBB, Gas, Pellet, Pistol, Review, Semi Auto, YouTube Video Tags: Webley, Nemesis, G&G, GPM1911

Air Venturi Springfield Armory M1 Carbine CO2 BB Rifle Field Test Review

1 Comment

Lots of CO2 BB Rifles getting reviewed these days and that’s kind of awesome, I remember a few years back and we barely had any realistic Replica BB rifles available to us. Now we have an ever increasing list of choices from Historical to Modern.

Todays Field Test Shooting Video focusses on the Air Venturi Springfield Armory M1 Carbine CO2 BB Rifle, I have not done my Table Top Video yet for it but I did make a preview video where I show it around a bit and talk about some basic specs. In short the Air Venturi Springfield Armory M1 Carbine CO2 BB Rifle is a CO2 powered semi auto 4.5mm Steel BB firing replica of the Springfield Armory M1 Carbine. It holds the CO2 and 15 rounds of Steel BB’s in its full size drop out metal magazine. Available with a plastic or upgraded wood stock.

For the Field Test Shooting part of this review I tested out the power and accuracy of the Air Venturi Springfield Armory M1 Carbine CO2 BB Rifle by first shooting 5 rounds through my Chronograph to establish the Feet Per Second velocity. I then placed a fresh paper target 30 feet downrange, while using a rested and seated shooting position I fired off 10 rounds into the target to see how tight of a group I can get with the Air Venturi Springfield Armory M1 Carbine CO2 BB Rifle. I used a brand new CO2 along with 5.1 grain 4.5mm Zinc coated Steel BB’s. The temperature was a conservative 22 degrees Celsius or 71 degrees Fahrenheit.

During my Chronograph velocity test I was a bit surprised to only obtain an average of 335 fps from the Air Venturi Springfield Armory M1 Carbine CO2 BB Rifle. Air Venturi claims closer to 425 so I am not sure why it was nearly 100 fps lower than claimed but perhaps the CO2 did not pierce as well as it could have, that said 335 fps does get the job done when shooting targets 20-30 feet away.

In terms of accuracy I was very pleased with the Air Venturi Springfield Armory M1 Carbine CO2 BB Rifle, it kind of made up for the slower than expected feet per second by getting a sub 1 inch 10 round group and I am not a big fan of peep sights so I was really not expecting these results. Right out of the box the Air Venturi Springfield Armory M1 Carbine CO2 BB Rifle shot pretty close to the bullseye, just s slight bit to the left and about 1-2 inches high. The rear sight is adjustable for elevation so that can be taken care of pretty easy.

All in all I really like the Air Venturi Springfield Armory M1 Carbine CO2 BB Rifle other than the lower than expected fps which may have been something to do with my rifle? I will have to try a fresh CO2 with it sometime to see if this can be improved but even with the lower velocity the Air Venturi Springfield Armory M1 Carbine CO2 BB Rifle performs well hitting what ever you are shooting at with excellent accuracy. The blowback action gives the Air Venturi Springfield Armory M1 Carbine CO2 BB Rifle just enough recoil feel to tap your shoulder a bit and of course give you that nice short and light single action only trigger.

Categories: 4.5mm / .177 cal, BB, Blowback, CO2, Field Test, Review, Semi Auto, YouTube Video, Rifle Tags: AirVenturi, Springfield Armory, M1 Carbine

Crosman Bushmaster MPW CO2 Blowback BB Machine Gun Field Test Review

No Comments

Make sure to watch my Table Top Video Review for the Crosman Bushmaster MPW CO2 Blowback BB Machine Gun for all the details and specifications. And if you have not already taken a look at the Crosman DPMS SBR CO2 Blowback BB M4 then watch those video reviews since both guns are very similar internally with some cosmetic differences.

The purpose of my Field Test Shooting Video is to find out how the airgun being reviewed performs in terms of velocity and accuracy, and if the ratings on paper end-up being the same or close to the tested results. Crosman claims the Crosman Bushmaster MPW CO2 Blowback BB Machine Gun is capable of shooting 5.1 grain 4.5mm Steel BB’s at up to 430 fps. When I tested the Crosman Bushmaster MPW CO2 Blowback BB Machine Gun using my Chronograph averaging out 5 shots using a brand new set of CO2 cartridges I averaged 385 fps. Note the temperature in my Indoor Airgun Sea Can Shooting Range was not super warm at about 20-22 degrees Celsius or right around 70 degrees Fahrenheit. I was able to get 405 fps from the Crosman DPMS SBR CO2 Blowback BB M4 but I have a feeling the temperate may have been a little bit warmer for the DPMS SBR Testing which does help to increase the fps.

Moving on to the accuracy portion of this Field Test Shooting Review for the Crosman Bushmaster MPW CO2 Blowback BB Machine Gun, I loaded up the 25 round magazine with the maximum amount t it would hold and then placed 10 semi auto shots on my paper target setup 30 feet downrange. I was using a rested and seated shooting position to help minimize human factor. I was a bit surprised that the Crosman Bushmaster MPW CO2 Blowback BB Machine Gun shot a 2.5 inch semi auto 10 shot group since the Crosman DPMS SBR CO2 Blowback BB M4 was able to get just under 1 inch when I performed the same test.

I then flipped the semi auto selector switch to full auto and dumped the remaining 15 rounds into my paper target in full auto mode and to my surprise the Crosman Bushmaster MPW CO2 Blowback BB Machine Gun actually tightened up it’s grouping a little bit closer to 1.5 inches which is amazing in full auto mode with the airgun rocking around a lot due to the blowback action.

In summary the Crosman Bushmaster MPW CO2 Blowback BB Machine Gun performed a lot like the Crosman DPMS SBR CO2 Blowback BB M4, just a little bit lower fps perhaps because of the difference in temperature when both of the airguns where tested. In semi auto mode I should have been able to get a tighter grouping, perhaps it was my performance on this day? But in full auto mode I was able to get nearly identical results as I shot with the Crosman DPMS SBR CO2 Blowback BB M4.

I think it really comes down to which of the Crosman AR type full auto BB rifles you like the look of since both are very capable shooters. Or just get both if you can’t decide :)

Categories: 4.5mm / .177 cal, BB, Blowback, CO2, Field Test, Full Auto, Review, Rifle, Semi Auto, YouTube Video Tags: Crosman, Crosman MPW, Bushmaster MPW, Crosman Remington DPMS SBR

Air Venturi Springfield Armory XDM Blowback CO2 BB Pistol Field Test Review

No Comments

In this Field Test Shooting Review Video I test out both the 3.8 Compact and 4.5 Full Size Air Venturi Springfield Armory XDM Blowback CO2 BB Pistols to see how they perform in both velocity and accuracy. I thought it would be interesting to see how the shorter and longer barreled versions compare side by side and if we sill see a difference in power and down range accuracy…

As always I use a brand new 12 gram CO2 along with 5.1 gran zinc coated steel BB’s for my testing and on this day the temperature in the Sea Can Indoor Airgun range was around 24 degrees Celsius or 75 degrees Fahrenheit.

Starting with the Chronograph test I placed 5 rounds through each gun and averaged out the result. The 3.8 inch Compact Air Venturi Springfield Armory XDM Blowback CO2 BB Pistol averaged 281 fps while the 4.5 inch Full Size Air Venturi Springfield Armory XDM Blowback CO2 BB Pistol averaged 303 fps. So it looks like the additional .7 inches increases the velocity about 20 fps!

I then shot 10 steel BB’s from each Air Venturi Springfield Armory XDM Blowback CO2 BB Pistol on my paper target setup 30 feet down range using a rested and seated shooting position. The 3.8 Compact Air Venturi Springfield Armory XDM Blowback CO2 BB Pistol shot about a 2 inch grouping but seemed to shoot rather low, just outside the outer rings so about 3-4 inches below the bullseye. Windage was good pretty much dead center left to right on the target.

I did find the 4.5 Air Venturi Springfield Armory XDM Blowback CO2 BB Pistol to shoot a little bit low as well but not as low as the 3.8 XDM staying inside the rings and about 2 inches below the bullseye, again all within about 2 inches and well center left to right.

At the end of the day both the 3.8 and 4.5 Air Venturi Springfield Armory XDM Blowback CO2 BB Pistols perfumed flawlessly for me with really great SAO triggers and a nice heavy blowback feel giving a noticeable recoil effect. The 3.8 Springfield Armory XDM did shoot a little bit slower as expected and a little bit lower on the target. It all comes down to choice and there are many with the Air Venturi Springfield Armory XDM Blowback Air Pistols. Airsoft or Steel BB, 3.8 inch or 4.5 inch, all black or silver slide. You decide which one is best for you :)

Categories: 4.5mm / .177 cal, BB, Blowback, CO2, Comparison, Field Test, Pistol, Review, Semi Auto, YouTube Video Tags: AirVenturi, Springfield Armory, XDM

Air Venturi Springfield Armory XDM BB vs Airsoft Pistol Comparison

1 Comment

For more of a traditional Table Top Features and Specifications video for the Air Venturi Springfield Armory XDM Air Pistol, then watch my Table Top Review for the Airsoft Springfield Armory XDM here.

Since both the 6mm Airsoft and 4.5mm Steel BB Air Venturi Springfield Armory XDM’s are nearly identical with only a few exceptions, I didn’t feel it was necessary to make another almost identical Table Top Video for the Steel BB firing Air Venturi Springfield Armory XDM. Instead I want to focus mainly on the differences in this comparison video.

Watch my Video for all the main differences but in short here they are for those reading this post:

  • Steel BB version uses CO2 while the Airsoft version uses Green Gas or Propane.

  • There is no orange tip on the Steel BB version while Airsoft versions come with orange tips installed.

  • Steel BB versions have 20 round full length magazines for both the 3.8 and 4.5 inch versions, while the Airsoft 3.8 compact comes with the shorter 14 round magazine and the Airsoft 4.5 comes with a longer 25 round magazine.

  • FPS for the Steel BB versions are 270fps for the 3.8 and 325fps for the 4.5, comparably the Airsoft 3.8 is claimed to have 280fps with the 4.5 version a bit higher at 330fps. (Keep in mind that steel BB’s weigh more at around .33 grams compared to the .20 gram plastic Airsoft BB’s used for testing).

  • I did notice that on the sliver slide version, my earlier Airsoft 4.5 had more of a parkerized metallic finish while my same Steel BB version I received at a later time had more of brushed stainless look to it. Air Venturi has since informed me that all silver slide version will now have the brushed stainless finish.

Categories: 6mm, 4.5mm / .177 cal, Airsoft, Blowback, CO2, Comparison, Gas, GBB, Pistol, Review, Semi Auto, YouTube Video Tags: AirVenturi, Springfield Armory, XDM