In this Field Test Shooting Video I test out the G&G Piranha MK I & TR GBB Airsoft Pistols in the Replica Airguns Indoor Sea Can Airgun Shooting Range to see what the real world performance is for these very similar Airsoft Pistols. I first place 5 rounds through my Chronograph for each Airsoft Gun using .25 gram Airsoft BB’s with fully gassed up magazines to find out what the actual fps velocity is. I then shoot 10 rounds from a seated and rested shooting position into fresh paper targets setup 30 feet down range to see just what we can expect in terms of accuracy from the G&G Piranha series.
Starting with my Chronograph test, a placed 5 rounds through my Chronograph with both the G&G Piranha MK I and G&G Piranha TR GBB Airsoft Pistols. Technically they should have performed nearly identical but not all guns are setup exactly the same out of the box and so the G&G Piranha MK I GBB Airsoft Pistol did shoot a bit hotter than the G&G Piranha & TR GBB Airsoft Pistol averaging 290 fps versus 257 fps. As a quick test I placed the magazine from the MK I into the TR and the G&G Piranha TR GBB Airsoft Pistol did shoot much hotter and very close to the G&G Piranha MK resultsI. I would assume the valves in these magazines where perhaps not letting out the same amount of Gas hence the difference in velocity. The velocity was well under the claimed 370+but I was using slightly heavier BB’s and it was a little cold in the Sea Can on this testing day, not quite room temperature. Around 19 degrees Celsius or 66 degrees Fahrenheit.
Moving onto the accuracy testing for the G&G Piranha MK I & TR GBB Airsoft Pistols, they performed pretty well shooting 10 round 2 inch groupings with both Airsoft Pistols shooting on the money vertically while the G&G Piranha MK I shot a bit to the left and the G&G Piranha TR shooting well centered all around.
All in both of the G&G Piranha MK I & TR GBB Airsoft Pistols performed good for me, I would have liked to have seen the fps higher since both guns where well under the claimed 370+ fps but for close quarter shooting you should have no problem with either of them and again maybe your magazine will shoot a bit hotter than mine did. The partial blowback action is snappy and quick with just enough recoil action to give that realistic shooting experience. The triggers on the G&G Piranha MK I & TR GBB Airsoft Pistols are really nice allowing for quick tight followup shots and again if you like the look and feel of a Glock but perhaps want something a bit more unique then you will want to consider one of the G&G Piranha series Airsoft Pistols know doubt.
In this Field Test Shooting Video I test out the G&G GPM92 GP2 GBB Airsoft Pistol in the Replica Airguns Indoor Sea Can Airgun Shooting Range to see what the real world performance is for this Beretta 92 styled G&G Airsoft Pistol. I first place 5 rounds through my Chronograph using .25 gram Airsoft BB’s with a fully gassed up magazine to find out what the actual FPS is. I then shoot 10 rounds from a seated and rested shooting position into a fresh paper target setup 30 feet down range to see just what we can expect in terms of accuracy from the G&G GPM92 GP2 GBB Airsoft Pistol.
Starting with my Chronograph test, the G&G GPM92 GP2 GBB Airsoft Pistol averaged 275 FPS with the fastest shot recorded at 278 FPS and the slowest being 274 FPS, so very consistent in terms of sustained FPS doing my testing. The velocity was well under the claimed 366 but I was using slightly heavier BB’s and it was a little cold in the Sea Can on this testing day, not quite room temperature. Around 19 degrees Celsius or 66 degrees Fahrenheit.
Moving onto the accuracy testing for the G&G GPM92 GP2 GBB Airsoft Pistol, it performed pretty decent shooting about a 10 round 1.5 inch grouping if I removed one flyer that pulled a bit to the left. The grouping was a little bit low but well centered left and right so even though the sights are none adjustable I should be able to pull up the shot placement a bit using the hop-up adjustment.
All in all the G&G GPM92 GP2 GBB Airsoft Pistol performed well for me, I would have liked to see the FPS just a bit higher but for close quarter shooting you should have no problem with it. The blowback action is nice and firm and the typical Beretta single and double action trigger is true to form allowing for a round in the pipe with the hammer safely decocted but ready to go with a quick release of the safety and a double action pull of the first round. The G&G GPM92 GP2 GBB Airsoft Pistol may be a bit bulky and heavy for some smaller handed shooter so keep that in mind.
Type: Gas Blowback Airsoft Pistol. Manufacturer: G&G Model: Piranha TR Materials: Metal & Polymer. Weight: 1.5 pounds (670 grams). Length: 7.8 inches total Barrel: 4.01 inches,Metal non-rifled smooth bore. Propulsion: Green gas or propane. Action: Blowback, single action only. Ammunition Type: 6mm plastic Airsoft BB's. Ammunition Capacity: 25rounds. FPS: 370+ fps.
Trigger Pull: The trigger pull on the G&G Piranha TR GBB Airsoft Pistol is typical single action only with a easy short take up (some of which is the trigger safety engaging), followed by a crisp predictable light release. The quick slide cycle allows for quick semi auto shooting with the G&G Piranha TR GBB Airsoft Pistol making it a great fast action shooter with quick target acquisition between shots.
Accuracy: I have not done my actual Field Test Shooting video review for the G&G Piranha TR GBB Airsoft Pistol but I expect it to perform similar to most G&G Blowback Gas Operated Airsoft Pistols and shoot consistently in the mid 300 fps with a 10 round grouping around 1-2 inches. Stay posted for my Field Test Shooting Video where I hope to confirm these predictions in the Sea Can indoor Airgun Shooting Range.
Build Quality: Like most off theG&G Airsoft guns, the G&G Piranha TR GBB Airsoft Pistol build quality is really nice. Fit and finish are excellent with virtually zero slide wiggle, you can also get the G&G Piranha TR GBB Airsoft Pistol in a two tone stainless slide and chrome finish barrel that looks really sharp. It also has an updated Ceramic Whirl Cylinder Valve technology from G&G that should significantly help with freezing in colder or fast shooting situations along with a new Hop-up system you can easily adjust using a special tool without taking the Airsoft gun apart.
Realism: The G&G Piranha TR GBB Airsoft Pistol as far as I can determines not an exact replica of any specific real steel gun in production but it does share looks, size and feel to that of the Glock but perhaps with an even more modernized look to it. You will find realistic function to the G&G Piranha MK I GBB Airsoft Pistoling terms of it’s operation with its full blowback action, working slide catch release, magazine release trigger safety and takedown lever allowing for it to be easily and quickly field stripped.
Good balance of metal and plastic for a balanced and light feel.
Partial slide Blowback operation should allow for even better gas performance and snappy operation.
Ceramic Whirl Cylinder Valve should expect to get decent amount of shots per green gas fill.
White dot sights front and back.
Nice two tone slide.
Has a working trigger safety.
Smaller spit grip perfect for people smaller hands.
Comes with hard shell case.
New Hop-up system for quick and easy fine adjustments with no need to field strip the gun.
Dual 20mm top and bottom Rails for accessories.
Comes in all black and two tone black and sliver.
Comes with high quality speed loader
Threaded barrel tip for add on mock suppressor.
Cons:
Sights are non adjustable.
Not an actual replica of any specific gun I know of but does share some Glock attributes.
No actual frame safety other than the trigger safeties, (not always a bad thing).
Comments:
Overall I really like the new G&G Piranha TR GBB Airsoft Pistol, it has a really modern look to it yet has a familiar feel. The G&G Piranha TR GBB Airsoft Pistol is fairly light weight with that quick and snappy partial slide allowing for very quick follow up shots. Combine all of that with the new Gas saving Ceramic Whirl Cylinder Valve I expect the G&G Piranha TR GBB Airsoft Pistol to perform really well when in action. I like that you have the option of the more subdued all black version or if you like your guns to be a little bit more flashy you can also get it in the two tone with black and stainless version. The TR version over MK 1 does allow for optics on top which personally would not be my choice for this gun but it’s nice that you have this option.
My Table Top Review Video of the G&G Piranha TR GBB Airsoft Pistol:
Type: Gas Blowback Airsoft Pistol. Manufacturer: G&G Model: Piranha MK I Materials: Metal & Polymer. Weight: 1.5 pounds (670 grams). Length: 7.8 inches total Barrel: 4.01 inches,Metal non-rifled smooth bore. Propulsion: Green gas or propane. Action: Blowback, single action only. Ammunition Type: 6mm plastic Airsoft BB's. Ammunition Capacity: 25rounds. FPS: 370+ fps.
Trigger Pull: The trigger pull on the G&G Piranha MK I GBB Airsoft Pistol is typical single action only with a easy short take up (some of which is the trigger safety engaging), followed by a crisp predictable light release. The quick slide cycle allows for some pretty quick semi auto shooting with the G&G Piranha MK I GBB Airsoft Pistol making it a great fast action shooter.
Accuracy: I have not done my actual Field Test Shooting video review for the G&G Piranha MK I GBB Airsoft Pistol but I expect it to perform similar to most G&G Blowback Gas Operated Airsoft Pistols and shoot consistently in the mid 300 fps with a 10 round grouping around 1-2 inches. Stay posted for my Field Test Shooting Video where I will confirm these predictions.
Build Quality: Like pretty much all G&G Airsoft guns, the G&G Piranha MK I GBB Airsoft Pistol build quality is really good. Fit and finish are excellent with virtually zero slide wiggle, the two tone stainless slide and chrome finish barrel look really good. It also has an updated Ceramic Whirl Cylinder Valve technology from G&G that should significantly help with freezing in colder or fast shooting situations along with a new Hop-up system you can easily adjust without taking the Airsoft gun apart.
Realism: The G&G Piranha MK I GBB Airsoft Pistol as far as I can determines not an exact replica of any specific real steel gun in production but it does share looks, size and feel to that of the Glock but perhaps with an even more modernized look to it. You will find realistic function to the G&G Piranha MK I GBB Airsoft Pistoling terms of it’s operation with its full blowback action, working slide catch release, magazine release trigger safety and takedown lever allowing for it to be field stripped.
Good balance of metal and plastic for a balanced and light feel.
Partial slide Blowback operation should allow for even better gas performance and snappy operation.
Ceramic Whirl Cylinder Valve should expect to get decent amount of shots per green gas fill.
White dot sights front and back.
Nice two tone slide.
Has a working trigger safety.
Smaller spit grip perfect for people smaller hands.
Comes with hard shell case.
New Hop-up system for quick and easy fine adjustments with no need to field strip the gun.
20mm Rail for accessories.
Comes in all black and two tone black and sliver.
Comes with high quality speed loader
Threaded barrel tip for add on mock suppressor.
Cons:
Sights are non adjustable.
Not an actual replica of any specific gun I know of but does share some Glock attributes.
No actual frame safety other than the trigger safeties, (not always a bad thing).
Comments:
Overall I really like the new G&G Piranha MK I GBB Airsoft Pistol, it has a really modern look to it yet has a familiar feel. The G&G Piranha MK I GBB Airsoft Pistol is fairly light weight with a quick and snappy slide allowing for very quick follow up shots. Combine all of that with the new Gas saving Ceramic Whirl Cylinder Valve I expect the G&G Piranha MK I GBB Airsoft Pistol to perform really well when in action. I like that you have the option of the more subdued all black version or if you like your guns to be a little bit more flashy you can also get it in the two tone with black and stainless version.
My Table Top Review Video of the G&G Piranha MK I GBB Airsoft Pistol:
Type: Gas Blowback Airsoft Pistol. Manufacturer: G&G Model: GPM92 GP2 Materials: Metal slide & frame, real wood grips. Weight: 2.3 pounds (1040 grams). Length: 8.9 inches total Barrel: 4.6 inches,Metal non-rifled smooth bore. Propulsion: Green gas or propane. Action: Blowback, single and double action. Ammunition Type: 6mm plastic Airsoft BB's. Ammunition Capacity: 28rounds. FPS: 366+ fps.
Trigger Pull: The trigger pull on the G&G GPM92 GP2 GBB Airsoft Pistol is very good in both single and double action. Double action is a bit longer but not that much heavier when shooting in single action. Single action shooting is short, light and crisp as you would expect when shooting a real steel Beretta 92 style pistol.
Accuracy: I have not done my actual Field Test Shooting video review for the G&G GPM92 GP2 GBB Airsoft Pistol but it should perform similar to my earlier review of the G&G GPM92 GBB Airsoft Pistol where it performed fairly well shooting in the mid 300 fps with a nice under 1 inch 10 round shot placement for 30 feet down range.
Build Quality: Like pretty much all G&G Airsoft guns, the G&G GPM92 GP2 GBB Airsoft Pistol build quality is right inline. Fit and finish where excellent and a lot of attention to detail was seen all over this Replica Airsoft Pistol. It also has an updated Ceramic Whirl Cylinder Valve technology from G&G that should significantly help with freezing in colder or fast shooting situations along with a new Hop-up system you can easily adjust without taking the Airsoft gun apart.
Realism: The G&G GPM92 GP2 GBB Airsoft Pistol is an excellent replica of the real steel Beretta Mod. 92FS, the safety even acts as a working de-cocker. You'll also find 5, 10, and 15 numbered markings on the backside of the magazine that would normally indicate how many bullets are in the magazine, a nice touch for sure! Everything works pretty much the same as it would on a real Beretta M9 including the ability to fully field strip the G&G GPM92 GP2 GBB Airsoft Pistol. I like the addition of th real wood grips that are a bit thicker than the plastic ones but if you ahed decent sized hands this shoudl not be a problem for you.
Ceramic Whirl Cylinder Valve should expect to get decent amount of shots per green gas fill.
White dot sights front and back.
Nice real wood grips.
Comes with hard shell case.
New Hop-up system for quick and easy fine adjustments with no need to field strip the gun.
20mm Rail for accessories.
comes in three different color schemes. Black, Silver, Gold.
Comes with high quality speed loader
Safety also works as a de-cocker.
Threaded removable barrel tip for add on mock suppressor.
Cons:
Sights are non adjustable.
Wood grips make the grips a bit thicker than plastic grips.
Price does go up especially if yo want the silver or gold version.
Comments:
I would have to say the new G&G GPM92 GP2 is one of the nicest Beretta Model 92FS Airsoft Pistols you are going to find out there, even a step up over the previous GPM92 model. There is a ton of attention to detail for sure, You also get the hard shell case with included high quality speed loader and G&G's updated Ceramic Valve and Revolutionary Whirl Cylinder Valve that help with freeze-up issues. It’s also nice that you no longer are required to filed strip the G&G GPM92 GP2 GBB Airsoft Pistol in order to adjust hop-up and the real wood grips just really finish off this quality product from G&G.
My Table Top Review of the G&G GPM92 GP2 GBB Airsoft Pistol:
In this Preview Unboxing Video I take a look at five Gas Blowback Airsoft Pistols. Three of them are from G&G and two are from ICS. All offer full blowback operation and are green gas or propane powered with full size metal drop out magazines.
I am super excite to showcase three awesome rifles in this Update Preview Unboxing Video. Two of which are Airsoft and one is a Steel BB shooter, all of which are semi and full auto selectable. In this video I do a bit of an unboxing and preview of each Rifle not going into too much detail as I want to leave most of the information for my Table Top and Filed Test Videos. The main purpose of this video is to let everyone know we have these Rifles in our Canada Replica Airguns Store now for sale.
I may as well talk about them in the order they appear in my video so lets start with the ICS CXP APE AEG Airsoft Rifle. The ICS CXP APE AEG Airsoft Rifle is a mostly metal Electric Airsoft Rifle with realistic electronic blowback operation along with a CNC machined aluminum upper and lower receiver. It comes with a hi-cap 300 round magazine and a Ver 2 Full Metal ICS Split Type Gearbox. The ICS CXP APE AEG Airsoft Rifle weighs in at just under 3kg.
Next I showcase the G&G SMC9 GBB Airsoft Carbine, a unique product that converts the G&G GTP9 pistol into a a semi and full auto Carbine and includes a 50 round extended magazine, there is an even higher capacity drum magazine made for this product! You will find a fold out stock along with a CNC Machined MLOK Rail for additional mounting options.
Last but perhaps one that I have been the most eagerly anticipating is the Crosman AK1 CO2 Blowback BB Rifle a twin CO2 Blowback 4.5mm Semi and Full auto AK style BB Rifle, finally a decent AK BB Rifle! The Crosman AK1 CO2 Blowback BB Rifle has a claimed fps of 430 and shoots 1400 rounds per minute in full auto, very similar to the Crosman DPMS series of AR styled CO2 Blowback Full Auto BB Rifles. The Crosman AK1 CO2 Blowback BB Rifle comes with a 25 round magazine and swing out rear adjustable stock.
In this Field Test Shooting Video I test out the Velocity and Accuracy of the Umarex VFC Heckler & Koch HK416 V2 AEG Airsoft Rifle by first placing 5 rounds through my Chronograph and recording the feet per second for each shot and then averaging them out. For the second portion of my Indoor Shooting Performance Test I setup a paper target 30 feet down range followed by shoot 10 rounds back to back to see what the spread or grouping size is. I followed this up with a nice long full auto burst just for fun to see if the grouping still remains nice and tight.
For my Velocity test I used .25 grain Plastic Airsoft BB’s rather than the normally tested .20 in the claimed fps of over 366 fps so I was expecting to get a little bit lower velocity results. I did manage to average right around 304 fps with all shots fairly consistently with the slowest being 302 fps and the fastest hitting 305 fps.
I then setup my brand new paper target and using a rested and seated shooting position from 30 feet back I placed my first 10 rounds into the target. The Umarex VFC Heckler & Koch HK416 V2 AEG Airsoft Rifle did shoot a little bit low close to the bottom of the rings but not as low as when I tested the Heckler & Koch HK416C version, I am sure some hop-up adjustment will get this closer to the mark. I did mange to get a really tight 10 round grouping of close to half an inch with most of the BB’s hitting one o top of the other I would ahed to say this is the best 30 foot accuracy results I have gotten from any Airsoft rifle to date! Full auto was as predicted, lots of fun with a nice hole in the paper/cardboard leaving about a 2 inch opening.
The Umarex VFC Heckler & Koch HK416 V2 AEG Airsoft Rifle performed really well for me and as already mentioned is crazy accurate. It had a slightly lower fps than the Heckler & Koch HK416C version which was a bit of a surprise but at 304 fps using .25 gram Airsoft BB’s this is about perfect for close quarters shooting adn even out to medium distances. Make sure not checkout all of our Umarex VFC Heckler & Koch over in the Replica Airguns Canada Online Store.
In this Field Test Shooting Video I test out the Velocity and Accuracy of the Umarex VFC Heckler & Koch HK416C V2 AEG Airsoft Rifle by first placing 5 rounds through my Chronograph and recording the feet per second of each shot then averaging them out. For the second portion of my Indoor Shooting Performance Test I setup a paper target 30 feet away and then shoot 10 rounds back to back to see what the spread or grouping size is. I follow this up with a full auto burst just for fun to see if the grouping still remains nice and tight.
For my Velocity test I used .25 grain Plastic Airsoft BB’s rather than the .20 in the claimed fps over 366 fps so I was expecting to get a little bit slower results. I did manage to average right around 325.5 fps with all shots consistently hitting either 325 or 326 fps so super consistent.
I then setup my brand new paper target and using a rested and seated shooting position from 30 feet back I placed my first 10 rounds into the target. This is when I discovered the Umarex VFC Heckler & Koch HK416C V2 AEG Airsoft Rifle liked to shoot fairly low even when using the raised elevation option on the rear sight. Because of this I had to aim a little bit higher on the paper target to place shoots more centered. Once I figure out my aim point I did mange to get a fairly tight 10 round grouping of close to an inch with a couple of stagers pushing it out to 2 inches. Full auto was as predicted, lots of fun with a nice hole in the paper/cardboard leaving about a 3.5 inch opening.
The Umarex VFC Heckler & Koch HK416C V2 AEG Airsoft Rifle performed well for me once I figured out that it liked to shoot rather low. I would suggest placing a bit of a spacer or riser under the rear sight to bring up the barrel at least for closer in shots where hop-up may not ark the Airsoft BB enough at that point. Other than that the Umarex VFC Heckler & Koch HK416C V2 AEG Airsoft Rifle had super consistent performance in terms of both FPS and accuracy.
Type: AEG Airsoft Rifles Manufacturer:Umarex / VFC Model:HK416 V2 Materials: Fiberglass reenforced plastic and metal. Weight: 7 pounds (3180 grams). Total Length: 28 - 31.1 inches (710-790). Barrel: 10.2 inches (260mm) non rifled. Propulsion: AEG. Action: Single action semi & full auto. Ammunition Type: .6mm plastic Airsoft BB’s. Ammunition Capacity: High cap 320 round magazines. FPS: 366+ fps.
Trigger Pull: The trigger pull on the Umarex VFC Heckler & Koch HK416 V2 AEG Airsoft Rifle is similar to a light single action trigger as they are essentially an electrical on off switch. There is about a quarter inch of take up with virtually no extra friction to let you know when the release is going to be, with a bit of use you will figure out exactly when the trigger will release the action.
Accuracy: At this time I have not made my Field Test Shooting Video or even shot the Umarex VFC Heckler & Koch HK416 V2 AEG Airsoft Rifle, but plan to make my Field Test Shooting Video shortly. So stay posted for that video coming out soon. I do expected Umarex VFC Heckler & Koch HK416 V2 AEG Airsoft Rifle to perform well as it is a high quality and not so inexpensive AEG Airsoft Rifle.
Build Quality: The Build quality on the Umarex VFC Heckler & Koch HK416 V2 AEG Airsoft Rifle looks to be really good, there are lots of quality metal parts throughout this Airsoft Rifle including the top and bottom receiver, rails, parts of the sights, flash hider, magazine, charging handle, selector switch, magazine release, forward assist, dust cover, buffet tube and trigger. VFC (Vega Force Company) is the actual manufacturer of this product line and they are well know for making high quality Airsoft products.
Realism: The Umarex VFC Heckler & Koch HK416 V2 AEG Airsoft Rifle is a 1 to 1 scale fully licensed replica of the real steel HK 416 compact CQB styled rifles . You’ll find that most part work in the same manner as with the real steel version including the Charging Handle, Forward Assist, Bolt Release, Magazine Release, Selector Switch and Pop-up sights.
Pros:
Full H&K Licensed via Umarex.
Made by VFC (Vega Force Company), well known for quality products.
Lots of metal parts where would find them on the real steel HK416.
Semi auto & full auto selectable.
No orange tip on Canada import version.
Comes with AR type compatible high capacity 320 round magazine.
Removable metal sights are adjustable for windage.
Lots of rail attachment positions.
Easy access to hop-up system.
Quality internals - V2 metal gearbox and built in Mosfet.
Fully adjustable rear stock.
Cons:
Price is on the higher end.
No elevation adjustment on sights.
Comments:
The Umarex VFC H&K AEG Airsoft product line is going to be on the higher end of the price spectrum for sure but you are getting a really quality product here fully H&K licensed. The Umarex VFC Heckler & Koch HK416 V2 AEG Airsoft Rifle has a really nice form factor allowing for a full size rear adjustable stock which will make your shooting position a lot more comfortable while still allowing for a rather compact form factor overall. I look forward to seeing how well the Umarex VFC Heckler & Koch HK416C V2 AEG Airsoft Rifle performs in my upcoming Field Test Shooting Video.
My Vimeo Table Top Review for the Umarex VFC HK416 V2 AEG Airsoft Rifle:
Type: AEG Airsoft Rifles Manufacturer:Umarex / VFC Model:HK416C V2 Materials: Fiberglass reenforced plastic and metal. Weight: 6.1 pounds (2780 grams). Total Length: 22.6 - 27.4 inches (573-696mm). Barrel: 8.3 inches (210mm) non rifled. Propulsion: AEG. Action: Single action semi & full auto. Ammunition Type: .6mm plastic Airsoft BB’s. Ammunition Capacity: High cap 320 round magazines. FPS: 366+ fps.
Trigger Pull: The trigger pull on the Umarex VFC Heckler & Koch HK416C V2 AEG Airsoft Rifle is similar to a light single action trigger as they are essentially an electrical on off switch. There is about a quarter inch of take up with virtually no extra friction to let you know when the release is going to be, with a bit of use you will figure out exactly when the trigger will release the action.
Accuracy: At this time I have not made my Field Test Shooting Video or even shot the Umarex VFC Heckler & Koch HK416C V2 AEG Airsoft Rifle, but plan to make my Field Test Shooting Video shortly. So stay posted for that video coming out soon. I do expected Umarex VFC Heckler & Koch HK416C V2 AEG Airsoft Rifle to perform well as it is a high quality and not so inexpensive AEG Airsoft Rifle.
Build Quality: The Build quality on the Umarex VFC Heckler & Koch HK416C V2 AEG Airsoft Rifle looks to be really good, there are lots of quality metal parts throughout this Airsoft Rifle including the top and bottom receiver, rails, sights, flash hider, magazine, charging handle, selector switch, magazine release, forward assist, dust cover and trigger. VFC (Vega Force Company) is the actual manufacturer of this product line and they are well know for making high quality Airsoft products.
Realism: The Umarex VFC Heckler & Koch HK416C V2 AEG Airsoft Rifle is a 1 to 1 scale fully licensed replica of the real steel HK 416 compact CQB styled rifles but in an even more compact design I believe specifically only found in Airsoft versions as I was not able to find the exact same model on the H&K Website. That said most part work in the same manner as you would find on the real steel version including the Charging Handle, Forward Assist, Bolt Release, Magazine Release, Selector Switch and Pop-up sights.
Pros:
Full H&K Licensed via Umarex.
Made by VFC (Vega Force Company), well known for quality products.
Lots of metal parts where would find them on the real steel HK416.
Semi auto & full auto selectable.
No orange tip on Canada import version.
Comes with AR type compatible high capacity 320 round magazine.
Pop up metal sights are adjustable for windage.
Lots of rail attachment positions.
Easy access to hop-up system.
Quality internals - V2 metal gearbox and built in Mosfet.
Ultra compact adjustable CQB stock.
Cons:
Price is on the higher end.
No elevation adjustment on sights.
Limited to physical size/type of battery used.
Comments:
The Umarex VFC H&K AEG Airsoft product line is going to be on the higher end of the price spectrum for sure but you are getting a really quality product here fully H&K licensed. The Umarex VFC Heckler & Koch HK416C V2 AEG Airsoft Rifle is perhaps one of my favorites as I like more simplistic and minimalist styles of guns and this one for sure fits into that category. Even though it is small in nature it is super solid and heavier then it looks for sure when you pick it up with all the metal parts making up its build quality. I look forward to seeing how well the Umarex VFC Heckler & Koch HK416C V2 AEG Airsoft Rifle performs in my upcoming Field Test Shooting Video.
My Vimeo Table Top Review for the Umarex VFC HK416C V2 AEG Airsoft Rifle:
In this video I show you four Premium AEG Airsoft Rifles made by VFC and distributed and H&K Licensed by Umarex. This is not a detailed review but rather I focus on the basic specification and show my reaction as I take my first look at all four Umarex H&K AEG Airsoft Rifles. I do show off some close up photos so you can get an idea on the finish and what some of the components look like.
For this Field Test Shooting Video I put the Specna Arms RRA SA-C10 Core and Specna Arms RRA SA-E10 Edge head to head to see just how they will compare in terms of FPS and Accuracy at least out to 30 feet. If you want to know more about each of these AEG Specna Arms Airsoft Rifles then checkout my Table Top Review where I show them up nice and close and also talk about their specifications and how they both compare to each other.
For my Chronograph test, I decided to go with .25 gram Airsoft BB’s, a little bit heavier than what was used for the claimed FPS of around 380 using the M120 spring which by the way is preinstalled in these guns for import into Canada. Both the Specna Arms RRA SA-C10 Core and E10 Edge shot pretty similar with the C10 Core averaging right around 300 FPS and the E10 Edge shooting a little bit faster with 318 FPS. Throw some lighter .20 gram Airsoft BB’s into the mix and these numbers would go up for sure. I was using the same 11.1 volt Li-Po battery for all of my testing in this video.
Next I placed a fresh paper target 30 feet downrange and placed 10 semi auto rounds into it using a seated and rested shooting position. Both Specna Arms AEG Airsoft Rifles shot about a 1 inch grouping. I did find with both of these Specna Arms rifles that when using the peep sight they shot too low and when using the top notch sight they shot too high at least at this distance. Of course the sights are fully adjustable so this can easily be taken care of and you can adjust the hop-up for even more elevation considerations. After my 10 shot semi auto test I placed both Specna Arms Airsoft rifles in Full Auto and let the paper have it! As expected the groupings did spread out a little bit but not all that much, perhaps opening up to around 3-4 inches.
After testing both the Specna Arms RRA SA-C10 Core and E10 Edge AEG Airsoft Rifles side by side you really can’t go wrong with either version as they performed very similarly on the Chronograph and on Target. If you can afford to pay the little bit more than I would go with an Edge Series Specna Arms product since you do get a lot of extras for the little bit more you pay. Well worth it!
Type: AEG Airsoft Rifles Manufacturer:Specna Arms. Model: RRA SA-C10 / RRA SA-E10 Materials: Fiberglass reenforced plastic and metal/aluminum. Weight: C10 4.9 pounds ( 2.2 kg) - E10 5.1 pounds (2.3 kg). Total Length: 21.7 - 25.2 inches (550 - 640mm). Barrel: 6.7 inch (170mm) inner 6.03mm tight bore barrel non rifled. Propulsion: AEG. Action: Single action semi & full auto. Ammunition Type: .6mm plastic Airsoft BB’s. Ammunition Capacity: Mid cap 120 round magazines. FPS: 375 - 390 fps with installed spring, included M90 spring will be lower fps.
Trigger Pull: The trigger pull on both of the Specna Arms RRA SA-C10 Core and E10 Edge AEG Airsoft Rifles is similar to a light single action trigger as they are essentially an electrical on off switch. There is a little bit of take up with virtually no extra friction to let you know when the release is going to be, with a bit of use you will figure out exactly when the trigger will release the action.
Accuracy: At this time I have not made my Field Test Shooting Video or even shot the Specna Arms RRA SA-C10 Core and E10 Edge AEG Airsoft Rifles, but plan to very soon. They are next on my list for Filed Test Shooting Videos so stay posted for that video coming out soon. I do expect them to perform well and will be shooting both of these models side by side to see if there is any noticeable difference between the lower cost Core versus the slightly more premium Edge Specna Arms versions.
Build Quality: One thing I can say is no matter which version of the Specna Arms AEG Air Rifles you deicide to go with (either a Core or Edge Series), you are getting extremely good value for your money and neither one is going to have any low quality parts in it. Even the lower cost Core Series will have fiber glass reenforced plastic and metal parts along with a metal gearbox and virtually almost the same build as the more premium and slightly higher priced Edge Series. You will get upgrades in the Edge Series such as a an aluminum receiver and buffer tube, a GATE X-ASR Mosfet, the New Orion Gearbox, deep laser engraved licensing and an additional magazine. All of this for the little bit more you pay for an Edge series Specna Arms AEG Airsoft rifle.
Realism: The Specna Arms RRA SA-C10 Core and E10 Edge AEG Airsoft Rifles are based on the AR15 or M16 platform of course in a very modern and PDW styled look. They look and feel the part for sure with lots of working parts including the safety, selector switch, charging handle, dust cover, adjustable rear stock, pop-up front and rear sights as you would expect. Most of the hardware should be interchangeable with a real steel AR if you want to personalize the look of your Specna Arms Rifle.
Pros:
Super affordable yet very high quality product for what you pay.
Two options to consider, both with good price points and value.
Quality components throughout both the Core and Edge series.
Rock River Arms Licensed with hologram on receiver.
ESA™ quick spring change system makes spring changes quick and easy.
Comes with two springs for potential indoor and outdoor usage.
Plastic parts are fiberglass reenforced making them very durable.
Quick release fully adjustable pop-up sights.
No orange tips on our Canada Store versions.
Lots of rial mounting options even on such short PDW styled AR’s.
Metal gearboxes with metal gears and mostly all metal parts inside.
Easy access to motor for any possible trouble shooting you may need to do.
Cons:
Popup sights are mostly plastic..
Need to hold back charging handle to access the hop-up wheel.
Comments:
Value for your money is what comes to mind when I think about the entire Specna Ams AEG Airsoft Riffle product line. And this goes for not only the lower priced Core Series but also the premium Edge Series. Both version are built supper tuff with quality components throughout. You are just getting upgrades you are probably going to do at some point in time with the Edge Series and of course more metal components when you spend about $100 more for a similar Edge version. I figure if you can muster up the extra cash then go with an Edge Specna Arms AEG Airsoft Rifle, that said, any of the Core models will be money well spent.
Make sure not also watch my previous Specna Arms YouTube Video where I introduce the product line, show you around several models and talk about the key differences between the Core and Edge versions.
My Vimeo Table Top Review for the Specna Arms RRA C10 Core & E10 Edge Airsoft Rifles:
We have a new line of Airsoft rifles from Specna Arms I am super happy to be introducing to the Replica Airguns Airsoft Community.
Specna Arms AEG Airsoft Rifles are extremely cost effective and offer value for what you pay that is amazing. In this YouTube Introduction Video I go over the main differences between the Core Series (lower priced) versus the Edge Series (mid priced) so that you can understand what the extra cost will get you when buying a Spenca Arms Edge Series AEG Airsoft Rifle over a Specna Arm Core Series AEG Airsoft Rifle.
I also show 12 different versions from the Specna Arms Core and Edge Series some with Rock River Arms licensing and some without.
Specna Arms Core Series
Price: Mid $200’s (CAD)
Materials: Fiberglass Reenforced Plastic & Metal
Mosfet System: No
Gear Box: Ver 2 Metal Fully Upgradeable
Spring System: ESA Quick Change - 2 Springs (380-310 fps)
Trigger Pull: The trigger pull on Tokyo Marui VSR-10 Pro Sniper Spring Bolt Action Airsoft Rifle is nice and short and light as would be expected form a bolt action sniper rifle. The take-up and release are virtually on existent, just nudge your finger a bit and this Airsoft rifle is firing a round down range.
Accuracy: So far I have not tested out the Tokyo Marui VSR-10 Pro Sniper Spring Bolt Action Airsoft Rifle but from what I have seen watching other YouTube videos, it looks to be very accurate right out of the box. The version I have has the Canada import legal heavier spring so it should shout right around 366 fps or a tad higher using .20 gram Airsoft BB’s. I will probably test mine out using heavier Airsoft BB’s when I perform my Field Test Shooting Video for the Tokyo Marui VSR-10 Pro Sniper Spring Bolt Action Airsoft Rifle.
Build Quality: The Tokyo Marui VSR-10 Pro Sniper Spring Bolt Action Airsoft Rifle like all Tokyo Marui products is very well made, there is a lot of plastic in this Airsoft Sniper rifle but it is of good quality, you will find metal in the barrel and bolt areas of course. The trigger, safety and sling attachments are also metal.
Realism: The Tokyo Marui VSR-10 Pro Sniper Spring Bolt Action Airsoft Rifle is based off of your typical bolt action hunting rifle with not a lot fo bells and whistles other than the included adjustable open sights but you can pimp it out with a ton of aftermarket modifications including much suppresses, scope mounts for a scope, bipods and pretty much all the internal parts can be upgraded and swapped out.
Pros:
Not a clone so all aftermarket parts will work on and in it.
No CO2 or batteries required, ready when you are.
Expect excellent accuracy at most ranges.
Easy to adjust on the field Hop-up.
Super easy to operate bolt action and very nice trigger.
Comes with heavier spring installed so more powerful than standard version.
Comes with integrated fully adjustable sights, no need for a scope to start shooting.
Comes with sling mounts which make it Bipod compatible.
No red tip.
Cons:
Does not come with scope plate so you will need that if you plan to install a stope on it.
Front sight is taped on with double sided tape.
Cost is high compared to other Spring powered Airsoft rifles on the market..
Comments:
There are lots of clones out there of the Tokyo Marui VSR-10 Pro Sniper Spring Bolt Action Airsoft Rifle but this is the real deal and so you will pay more for it for sure but you will get Tokyo Marui quality and performance. That can not be said for the clone versions. If you do plan on upgrading yours down the road the Tokyo Marui version will accept all the aftermarket add ons and parts which again the clones may not and so you could end up wasting your money on parts that don’t fit with the other versions. Something to keep in mind when adding up all the costs. One thing to be aware of with the Tokyo Marui VSR-10 Pro Sniper Spring Bolt Action Airsoft Rifle is the bolt is a bit firmer with the upgraded spring dn so you need to make sure it is all the way forward before twisting and releasing. If you don’t it will not lock into place and you will end up scratching the back paint off of the area just in front of the safety, not a big deal, you can always touch it up easy enough.
My Vimeo Table Top Review for theTokyo Marui VSR-10 Pro Sniper Spring Bolt Action Airsoft Rifle:
Type: Airsoft Pistol. Manufacturer:KWC. Model: PT92 Materials: Almost entirely all Metal. Weight: 2.4 pounds (1089 grams). Barrel: 4.5 inches, metal non-rifled. Propulsion: 12 gram CO2. Action: Semi and full auto, single and double action with full blowback. Ammunition Type: 6mm Plastic Airsoft BB's. Ammunition Capacity: 27 rounds full size drop out metal magazine. FPS: 388 using .25 gram Airsoft BB’s.
Trigger Pull: The trigger pull on the KWC PT92 CO2 Blowback Airsoft Pistol is good in both single and double action. Of course in single action the trigger is much shorter and lighter but that said double action is still very usable. Once you fire a round in either double or single action the blowback action will continue to cock the hammer back allowing for single action followup shots.
Accuracy: The KWC PT92 CO2 Blowback Airsoft Pistol performed OK during my Field Test Shooting review in terms of accuracy. I shot it first in semi auto to get a sense of the overall accuracy and in terms of elevation it was right in the middle of the target. I did find the shots spread out a bit side to side perhaps as much as 4-5 inches during my test grouping. As expected when I flipped the happy switch to full auto the KWC PT92 CO2 Blowback Airsoft Pistol pretty much sprayed the target working its way up as the recoil from the full auto blowback action lifted the barrel. In terms of power the KWC PT92 CO2 Blowback Airsoft Pistol shot pretty hot, I was using .25 gram Airsoft BB’s and was still able to achieve close to 400 fps.
Build Quality: The KWC PT92 CO2 Blowback Airsoft Pistol like the other all metal KWC made Beretta 92 or Taurus PT92 copies out there being sold under different company names, is a good value blowback Beretta Taurus Airgun no matter which version you get. It’s not the best or worst, right about in the middle but most of the bugs have been worked out since it came out just after the KWC 1911 line and that’s been out for some time now. I find the finish does come off a bit easy but when this happens it kind of gives the Airgun a more realistic and slightly worn in look to it.
Realism: The KWC PT92 CO2 Blowback Airsoft Pistol is a One to One replica of the real steel Taurus PT92 and does a great job at replicating it. You would be hard pressed to see any differences in the Airgun version versus the 9mm caliber firing version until you pick one up and work the parts a bit. Even so pretty much all the mechanical parts work the same as a real steel Taurus PT92 including the ability to filed strip the Airgun version and gain access to the hop-up and other internal parts.
Pros:
All metal construction.
Full length blowback action with nice heavy recoil.
Accurate Taurus PT92 replica.
Single and double action triggers both feel good.
Double stack style metal magazine holds the CO2 and Airsoft BB’s.
No ugly white writing ( warning instructions) on the gun.
Fully filed strippable.
Adjustable Hop-up.
Recessed barrel for added realism.
FPS is fairly high for a full blowback gun.
Cons:
Finish on KWC guns can wear off quickly in the high spots but has gotten better over the years.
Full blowback action especially when in full auto mode will eat up a lot of CO2.
Comments: If you are a Beretta 92 or Taurus PT92 fan than I am sure you have already taken a look at the KWC line of Beretta 92 and Taurus PT92 Airguns, maybe in a steel BB version or Airsoft version? KWC first offered it in this PT92 style and then later brought out a more true to form Beretta 92 version. Depending on where you live and which model you buy you may or may not have the full auto feature but to be honest full auto is fun at first but then you realize you don’t really hit much with it and just end up wasting a lot fo CO2 and BB’s. Checkout our Replica Airguns Canada and US Stores for all the different versions and models of this KWC Beretta and Taurus style Airgun.
My Vimeo Video Review for the KWC PT92 CO2 Blowback Airsoft Pistol:
Type: Airsoft Pistol. Manufacturer:KWC. Model: M1911 Materials: Almost entirely all Metal. Weight: 1.97 pounds (894 grams). Barrel: 4.5 inches, metal non-rifled. Propulsion: 12 gram CO2. Action: Semi auto, single action only with full blowback. Ammunition Type: 6mm Plastic Airsoft BB's. Ammunition Capacity: 14-15 rounds full size drop out metal magazine. FPS: 360+.
Trigger Pull: The Single Action Only trigger pull on the KWC M1911 CO2 Blowback Airsoft Pistol is exactly as it should be and just like what you would find on a real steel Colt 1911 pistol. That would be short, light and crisp. As there is no double action mode, you are required to rack the slide back to chamber a rounds and cock the hammer for the first shot, afterwards the blowback action will do this for you.
Accuracy: I wasn’t overly impressed with the accuracy of the KWC M1911 CO2 Blowback Airsoft Pistol when I tested it out in the Replica Airguns Indoor Sea Can Airgun Range but it is what it is. The M1911 shot really high and a bit loose getting about a 5 inch 10 shot grouping, perhaps a hop-up adjustment was in order but this is how it shot right out of the box which is how I test all my Airguns. In terms of power the KWC M1911 CO2 Blowback Airsoft Pistol was bang on shooting .25 gram Airsoft BB’s at right around 350 fps.
Build Quality: The KWC M1911 CO2 Blowback Airsoft Pistol like the other all metal KWC made 1911’s out there being sold under different company names, is a good value Blowback 1911 Airgun no matter which version you get. It’s not the best or worst, right about in the middle but most of the bugs have been worked out since this is one of the longes CO2 1911’s out there and for the most part has stayed about the same. I find the finish does come off a bit easy but when this happens it kind of gives the 1911 Airgun a more realistic and slightly worn in look to it.
Realism: The KWC M1911 CO2 Blowback Airsoft Pistol is a One to One replica of the real steel M1911 A1 and does a great job at replicating it. You would be hard pressed to see any differences in the Airgun version and the .45 caliber firing version until you pick one up and work the parts a bit, even so pretty much all the mechanical parts work the same as a real steel M1911 A1 including the ability to filed strip the Airgun version and gain access to the hop-up and other internal parts.
Pros:
All metal construction.
Full length blowback action with nice heavy recoil.
Accurate Colt M1911 A1 replica.
Single action only trigger feels good, short light and crips.
Accurate trigger design and working grip safety.
Metal magazine holds the CO2 and 14-15 Airsoft BB’s.
No ugly white writing (warning instructions) on the slide of the gun.
Fully filed strippable.
Adjustable Hop-up.
Recessed barrel for added realism.
FPS is just about perfect, just over 360 fps using .20 gram BB’s, not too powerful but Canada import friendly.
Cons:
Finish on KWC guns can wear off quickly in the high spots but has gotten better over the years.
Full blowback action will eat up a lot of CO2.
Comments: I have always been a fan of the 1911 pistol and the KWC M1911 CO2 Blowback Airsoft Pistol is no exception to this. Like all of the KWC 1911’s out there being redistributed by the big airgun companies the KWC version is really no different other than more simple KWC branding and with no licensing on the Airgun to speak of. Some people prefer the cleaner look to it and some will like to have licensed versions, to each their own. Do some looking around on our website and find a KWC made 1911 you like best, perhaps a simple KWC M1911 A1 like the one reviewed here or maybe a more tactical version with all the more modern updates to it like a rail, ambidextrous controls and tactical triggers and hammers.
My Vimeo Video Review for the KWC M1911 CO2 Blowback Airsoft Pistol:
If you have not already watched my Preview video for both of these Airsoft pistols then make sure to watch that video for details and specifications along with some nice tight shots of each Airsoft gun.
Another multi gun Field Test Shooting Review, in this Indoor Sea Can Field Test Shooting Video I test out the KWC M1911 and PT92 Full Blowback CO2 Airsoft Pistols. I first place 5 6mm .25 gram plastic Airsoft BB’s through my Chronograph to find out what the real world velocity is for each Airsoft Pistol and then I perform my accuracy test where I shoot multiple rounds into a paper target 30 feet down range to see how close of a grouping I can get with each Airgun. I use a seated and rested shooting position to eliminate as much human factor as possible. By the way is used a brand new 12 gram CO2 and the temperature was 25 degrees Celsius (77 degree Fahrenheit) inside the Airgun Sea Can Shooting Range.
Starting with the KWC M1911 CO2 Blowback Airsoft Pistol I averaged 351 fps with the fastest shot being 353 and the slowest shot 345, so very consistent for sure! Accuracy for the KWC M1911 CO2 Blowback Airsoft Pistol could have been a bit better, I had to adjust my aim point to just under the bottom rings and even so the KWC M1911 wanted to shoot high, I was able to get around a 5 inch 10 shot grouping but was hoping for a bit better.
Next I tested out the KWC PT92 CO2 Blowback Airsoft Pistol which does have a full auto option. For the velocity portion of my Field Test the KWC PT92 did shoot a bit after than the MWC M1911 getting an average fps of 388 with the fastest shot hitting 396 and the slowest shot at 383 so again very consistent performance. Since the KWC PT92 CO2 Blowback Airsoft Pistol is capable of full auto shooting I decided to shoot 5 rods on my paper target to get a base accuracy and this resulted in a bit of a lateral spread fairly close to the bullseye about 4-5 inches apart. I then did a mag dump and as expected pretty much sprayed 6mm Airsoft BB’s all over the place but most shot a bit high and to the left probably because of the blowback recoil action.
The KWC M1911 and PT92 CO2 Blowback Airsoft Pistols are both classic Airguns and great options if your looking for a 1911 or Beretta styled Airgun to add to your collection without all the markings and white writing on them.
You’ve seen them all before but have you seen them in this exact configuration? All the Airguns I show off in this video are made by KWC and generally come in either Steel BB and or Airsoft versions along with non-blowback and blowback versions. You can even find most of them redistributed by other companies like Umarex, Cybergun, Gletcher, Crosman and others even licensed in some cases.
The versions I am showing today I have not review yet in these exact configuration and all of them are the KWC made and distributed unlicensed versions, so nice and clean with virtually none of that ugly white lettering on them…
