In this Field Test Shooting Video I test out the Velocity and Accuracy of the Umarex VFC Heckler & Koch HK416 V2 AEG Airsoft Rifle by first placing 5 rounds through my Chronograph and recording the feet per second for each shot and then averaging them out. For the second portion of my Indoor Shooting Performance Test I setup a paper target 30 feet down range followed by shoot 10 rounds back to back to see what the spread or grouping size is. I followed this up with a nice long full auto burst just for fun to see if the grouping still remains nice and tight.
For my Velocity test I used .25 grain Plastic Airsoft BB’s rather than the normally tested .20 in the claimed fps of over 366 fps so I was expecting to get a little bit lower velocity results. I did manage to average right around 304 fps with all shots fairly consistently with the slowest being 302 fps and the fastest hitting 305 fps.
I then setup my brand new paper target and using a rested and seated shooting position from 30 feet back I placed my first 10 rounds into the target. The Umarex VFC Heckler & Koch HK416 V2 AEG Airsoft Rifle did shoot a little bit low close to the bottom of the rings but not as low as when I tested the Heckler & Koch HK416C version, I am sure some hop-up adjustment will get this closer to the mark. I did mange to get a really tight 10 round grouping of close to half an inch with most of the BB’s hitting one o top of the other I would ahed to say this is the best 30 foot accuracy results I have gotten from any Airsoft rifle to date! Full auto was as predicted, lots of fun with a nice hole in the paper/cardboard leaving about a 2 inch opening.
The Umarex VFC Heckler & Koch HK416 V2 AEG Airsoft Rifle performed really well for me and as already mentioned is crazy accurate. It had a slightly lower fps than the Heckler & Koch HK416C version which was a bit of a surprise but at 304 fps using .25 gram Airsoft BB’s this is about perfect for close quarters shooting adn even out to medium distances. Make sure not checkout all of our Umarex VFC Heckler & Koch over in the Replica Airguns Canada Online Store.
In this Field Test Shooting Video I test out the Velocity and Accuracy of the Umarex VFC Heckler & Koch HK416C V2 AEG Airsoft Rifle by first placing 5 rounds through my Chronograph and recording the feet per second of each shot then averaging them out. For the second portion of my Indoor Shooting Performance Test I setup a paper target 30 feet away and then shoot 10 rounds back to back to see what the spread or grouping size is. I follow this up with a full auto burst just for fun to see if the grouping still remains nice and tight.
For my Velocity test I used .25 grain Plastic Airsoft BB’s rather than the .20 in the claimed fps over 366 fps so I was expecting to get a little bit slower results. I did manage to average right around 325.5 fps with all shots consistently hitting either 325 or 326 fps so super consistent.
I then setup my brand new paper target and using a rested and seated shooting position from 30 feet back I placed my first 10 rounds into the target. This is when I discovered the Umarex VFC Heckler & Koch HK416C V2 AEG Airsoft Rifle liked to shoot fairly low even when using the raised elevation option on the rear sight. Because of this I had to aim a little bit higher on the paper target to place shoots more centered. Once I figure out my aim point I did mange to get a fairly tight 10 round grouping of close to an inch with a couple of stagers pushing it out to 2 inches. Full auto was as predicted, lots of fun with a nice hole in the paper/cardboard leaving about a 3.5 inch opening.
The Umarex VFC Heckler & Koch HK416C V2 AEG Airsoft Rifle performed well for me once I figured out that it liked to shoot rather low. I would suggest placing a bit of a spacer or riser under the rear sight to bring up the barrel at least for closer in shots where hop-up may not ark the Airsoft BB enough at that point. Other than that the Umarex VFC Heckler & Koch HK416C V2 AEG Airsoft Rifle had super consistent performance in terms of both FPS and accuracy.
Type: AEG Airsoft Rifles Manufacturer:Umarex / VFC Model:HK416 V2 Materials: Fiberglass reenforced plastic and metal. Weight: 7 pounds (3180 grams). Total Length: 28 - 31.1 inches (710-790). Barrel: 10.2 inches (260mm) non rifled. Propulsion: AEG. Action: Single action semi & full auto. Ammunition Type: .6mm plastic Airsoft BB’s. Ammunition Capacity: High cap 320 round magazines. FPS: 366+ fps.
Trigger Pull: The trigger pull on the Umarex VFC Heckler & Koch HK416 V2 AEG Airsoft Rifle is similar to a light single action trigger as they are essentially an electrical on off switch. There is about a quarter inch of take up with virtually no extra friction to let you know when the release is going to be, with a bit of use you will figure out exactly when the trigger will release the action.
Accuracy: At this time I have not made my Field Test Shooting Video or even shot the Umarex VFC Heckler & Koch HK416 V2 AEG Airsoft Rifle, but plan to make my Field Test Shooting Video shortly. So stay posted for that video coming out soon. I do expected Umarex VFC Heckler & Koch HK416 V2 AEG Airsoft Rifle to perform well as it is a high quality and not so inexpensive AEG Airsoft Rifle.
Build Quality: The Build quality on the Umarex VFC Heckler & Koch HK416 V2 AEG Airsoft Rifle looks to be really good, there are lots of quality metal parts throughout this Airsoft Rifle including the top and bottom receiver, rails, parts of the sights, flash hider, magazine, charging handle, selector switch, magazine release, forward assist, dust cover, buffet tube and trigger. VFC (Vega Force Company) is the actual manufacturer of this product line and they are well know for making high quality Airsoft products.
Realism: The Umarex VFC Heckler & Koch HK416 V2 AEG Airsoft Rifle is a 1 to 1 scale fully licensed replica of the real steel HK 416 compact CQB styled rifles . You’ll find that most part work in the same manner as with the real steel version including the Charging Handle, Forward Assist, Bolt Release, Magazine Release, Selector Switch and Pop-up sights.
Pros:
Full H&K Licensed via Umarex.
Made by VFC (Vega Force Company), well known for quality products.
Lots of metal parts where would find them on the real steel HK416.
Semi auto & full auto selectable.
No orange tip on Canada import version.
Comes with AR type compatible high capacity 320 round magazine.
Removable metal sights are adjustable for windage.
Lots of rail attachment positions.
Easy access to hop-up system.
Quality internals - V2 metal gearbox and built in Mosfet.
Fully adjustable rear stock.
Cons:
Price is on the higher end.
No elevation adjustment on sights.
Comments:
The Umarex VFC H&K AEG Airsoft product line is going to be on the higher end of the price spectrum for sure but you are getting a really quality product here fully H&K licensed. The Umarex VFC Heckler & Koch HK416 V2 AEG Airsoft Rifle has a really nice form factor allowing for a full size rear adjustable stock which will make your shooting position a lot more comfortable while still allowing for a rather compact form factor overall. I look forward to seeing how well the Umarex VFC Heckler & Koch HK416C V2 AEG Airsoft Rifle performs in my upcoming Field Test Shooting Video.
My Vimeo Table Top Review for the Umarex VFC HK416 V2 AEG Airsoft Rifle:
Type: AEG Airsoft Rifles Manufacturer:Umarex / VFC Model:HK416C V2 Materials: Fiberglass reenforced plastic and metal. Weight: 6.1 pounds (2780 grams). Total Length: 22.6 - 27.4 inches (573-696mm). Barrel: 8.3 inches (210mm) non rifled. Propulsion: AEG. Action: Single action semi & full auto. Ammunition Type: .6mm plastic Airsoft BB’s. Ammunition Capacity: High cap 320 round magazines. FPS: 366+ fps.
Trigger Pull: The trigger pull on the Umarex VFC Heckler & Koch HK416C V2 AEG Airsoft Rifle is similar to a light single action trigger as they are essentially an electrical on off switch. There is about a quarter inch of take up with virtually no extra friction to let you know when the release is going to be, with a bit of use you will figure out exactly when the trigger will release the action.
Accuracy: At this time I have not made my Field Test Shooting Video or even shot the Umarex VFC Heckler & Koch HK416C V2 AEG Airsoft Rifle, but plan to make my Field Test Shooting Video shortly. So stay posted for that video coming out soon. I do expected Umarex VFC Heckler & Koch HK416C V2 AEG Airsoft Rifle to perform well as it is a high quality and not so inexpensive AEG Airsoft Rifle.
Build Quality: The Build quality on the Umarex VFC Heckler & Koch HK416C V2 AEG Airsoft Rifle looks to be really good, there are lots of quality metal parts throughout this Airsoft Rifle including the top and bottom receiver, rails, sights, flash hider, magazine, charging handle, selector switch, magazine release, forward assist, dust cover and trigger. VFC (Vega Force Company) is the actual manufacturer of this product line and they are well know for making high quality Airsoft products.
Realism: The Umarex VFC Heckler & Koch HK416C V2 AEG Airsoft Rifle is a 1 to 1 scale fully licensed replica of the real steel HK 416 compact CQB styled rifles but in an even more compact design I believe specifically only found in Airsoft versions as I was not able to find the exact same model on the H&K Website. That said most part work in the same manner as you would find on the real steel version including the Charging Handle, Forward Assist, Bolt Release, Magazine Release, Selector Switch and Pop-up sights.
Pros:
Full H&K Licensed via Umarex.
Made by VFC (Vega Force Company), well known for quality products.
Lots of metal parts where would find them on the real steel HK416.
Semi auto & full auto selectable.
No orange tip on Canada import version.
Comes with AR type compatible high capacity 320 round magazine.
Pop up metal sights are adjustable for windage.
Lots of rail attachment positions.
Easy access to hop-up system.
Quality internals - V2 metal gearbox and built in Mosfet.
Ultra compact adjustable CQB stock.
Cons:
Price is on the higher end.
No elevation adjustment on sights.
Limited to physical size/type of battery used.
Comments:
The Umarex VFC H&K AEG Airsoft product line is going to be on the higher end of the price spectrum for sure but you are getting a really quality product here fully H&K licensed. The Umarex VFC Heckler & Koch HK416C V2 AEG Airsoft Rifle is perhaps one of my favorites as I like more simplistic and minimalist styles of guns and this one for sure fits into that category. Even though it is small in nature it is super solid and heavier then it looks for sure when you pick it up with all the metal parts making up its build quality. I look forward to seeing how well the Umarex VFC Heckler & Koch HK416C V2 AEG Airsoft Rifle performs in my upcoming Field Test Shooting Video.
My Vimeo Table Top Review for the Umarex VFC HK416C V2 AEG Airsoft Rifle:
In this video I show you four Premium AEG Airsoft Rifles made by VFC and distributed and H&K Licensed by Umarex. This is not a detailed review but rather I focus on the basic specification and show my reaction as I take my first look at all four Umarex H&K AEG Airsoft Rifles. I do show off some close up photos so you can get an idea on the finish and what some of the components look like.
For this Field Test Shooting Video I put the Specna Arms RRA SA-C10 Core and Specna Arms RRA SA-E10 Edge head to head to see just how they will compare in terms of FPS and Accuracy at least out to 30 feet. If you want to know more about each of these AEG Specna Arms Airsoft Rifles then checkout my Table Top Review where I show them up nice and close and also talk about their specifications and how they both compare to each other.
For my Chronograph test, I decided to go with .25 gram Airsoft BB’s, a little bit heavier than what was used for the claimed FPS of around 380 using the M120 spring which by the way is preinstalled in these guns for import into Canada. Both the Specna Arms RRA SA-C10 Core and E10 Edge shot pretty similar with the C10 Core averaging right around 300 FPS and the E10 Edge shooting a little bit faster with 318 FPS. Throw some lighter .20 gram Airsoft BB’s into the mix and these numbers would go up for sure. I was using the same 11.1 volt Li-Po battery for all of my testing in this video.
Next I placed a fresh paper target 30 feet downrange and placed 10 semi auto rounds into it using a seated and rested shooting position. Both Specna Arms AEG Airsoft Rifles shot about a 1 inch grouping. I did find with both of these Specna Arms rifles that when using the peep sight they shot too low and when using the top notch sight they shot too high at least at this distance. Of course the sights are fully adjustable so this can easily be taken care of and you can adjust the hop-up for even more elevation considerations. After my 10 shot semi auto test I placed both Specna Arms Airsoft rifles in Full Auto and let the paper have it! As expected the groupings did spread out a little bit but not all that much, perhaps opening up to around 3-4 inches.
After testing both the Specna Arms RRA SA-C10 Core and E10 Edge AEG Airsoft Rifles side by side you really can’t go wrong with either version as they performed very similarly on the Chronograph and on Target. If you can afford to pay the little bit more than I would go with an Edge Series Specna Arms product since you do get a lot of extras for the little bit more you pay. Well worth it!
Type: AEG Airsoft Rifles Manufacturer:Specna Arms. Model: RRA SA-C10 / RRA SA-E10 Materials: Fiberglass reenforced plastic and metal/aluminum. Weight: C10 4.9 pounds ( 2.2 kg) - E10 5.1 pounds (2.3 kg). Total Length: 21.7 - 25.2 inches (550 - 640mm). Barrel: 6.7 inch (170mm) inner 6.03mm tight bore barrel non rifled. Propulsion: AEG. Action: Single action semi & full auto. Ammunition Type: .6mm plastic Airsoft BB’s. Ammunition Capacity: Mid cap 120 round magazines. FPS: 375 - 390 fps with installed spring, included M90 spring will be lower fps.
Trigger Pull: The trigger pull on both of the Specna Arms RRA SA-C10 Core and E10 Edge AEG Airsoft Rifles is similar to a light single action trigger as they are essentially an electrical on off switch. There is a little bit of take up with virtually no extra friction to let you know when the release is going to be, with a bit of use you will figure out exactly when the trigger will release the action.
Accuracy: At this time I have not made my Field Test Shooting Video or even shot the Specna Arms RRA SA-C10 Core and E10 Edge AEG Airsoft Rifles, but plan to very soon. They are next on my list for Filed Test Shooting Videos so stay posted for that video coming out soon. I do expect them to perform well and will be shooting both of these models side by side to see if there is any noticeable difference between the lower cost Core versus the slightly more premium Edge Specna Arms versions.
Build Quality: One thing I can say is no matter which version of the Specna Arms AEG Air Rifles you deicide to go with (either a Core or Edge Series), you are getting extremely good value for your money and neither one is going to have any low quality parts in it. Even the lower cost Core Series will have fiber glass reenforced plastic and metal parts along with a metal gearbox and virtually almost the same build as the more premium and slightly higher priced Edge Series. You will get upgrades in the Edge Series such as a an aluminum receiver and buffer tube, a GATE X-ASR Mosfet, the New Orion Gearbox, deep laser engraved licensing and an additional magazine. All of this for the little bit more you pay for an Edge series Specna Arms AEG Airsoft rifle.
Realism: The Specna Arms RRA SA-C10 Core and E10 Edge AEG Airsoft Rifles are based on the AR15 or M16 platform of course in a very modern and PDW styled look. They look and feel the part for sure with lots of working parts including the safety, selector switch, charging handle, dust cover, adjustable rear stock, pop-up front and rear sights as you would expect. Most of the hardware should be interchangeable with a real steel AR if you want to personalize the look of your Specna Arms Rifle.
Pros:
Super affordable yet very high quality product for what you pay.
Two options to consider, both with good price points and value.
Quality components throughout both the Core and Edge series.
Rock River Arms Licensed with hologram on receiver.
ESA™ quick spring change system makes spring changes quick and easy.
Comes with two springs for potential indoor and outdoor usage.
Plastic parts are fiberglass reenforced making them very durable.
Quick release fully adjustable pop-up sights.
No orange tips on our Canada Store versions.
Lots of rial mounting options even on such short PDW styled AR’s.
Metal gearboxes with metal gears and mostly all metal parts inside.
Easy access to motor for any possible trouble shooting you may need to do.
Cons:
Popup sights are mostly plastic..
Need to hold back charging handle to access the hop-up wheel.
Comments:
Value for your money is what comes to mind when I think about the entire Specna Ams AEG Airsoft Riffle product line. And this goes for not only the lower priced Core Series but also the premium Edge Series. Both version are built supper tuff with quality components throughout. You are just getting upgrades you are probably going to do at some point in time with the Edge Series and of course more metal components when you spend about $100 more for a similar Edge version. I figure if you can muster up the extra cash then go with an Edge Specna Arms AEG Airsoft Rifle, that said, any of the Core models will be money well spent.
Make sure not also watch my previous Specna Arms YouTube Video where I introduce the product line, show you around several models and talk about the key differences between the Core and Edge versions.
My Vimeo Table Top Review for the Specna Arms RRA C10 Core & E10 Edge Airsoft Rifles:
We have a new line of Airsoft rifles from Specna Arms I am super happy to be introducing to the Replica Airguns Airsoft Community.
Specna Arms AEG Airsoft Rifles are extremely cost effective and offer value for what you pay that is amazing. In this YouTube Introduction Video I go over the main differences between the Core Series (lower priced) versus the Edge Series (mid priced) so that you can understand what the extra cost will get you when buying a Spenca Arms Edge Series AEG Airsoft Rifle over a Specna Arm Core Series AEG Airsoft Rifle.
I also show 12 different versions from the Specna Arms Core and Edge Series some with Rock River Arms licensing and some without.
Specna Arms Core Series
Price: Mid $200’s (CAD)
Materials: Fiberglass Reenforced Plastic & Metal
Mosfet System: No
Gear Box: Ver 2 Metal Fully Upgradeable
Spring System: ESA Quick Change - 2 Springs (380-310 fps)
Perhaps you might call this a followup video since I already made a full Field Test Shooting Video of the all black version of this pistol and you may wonder if the color of a gun could in some way effect how it performs? Well I don’t think color would really matter but it has been over 6 years since I did my original Field Test Shooting video fo the Umarex Colt Python 357 Magnum Chrome CO2 BB Revolver and so perhaps some things have changed, maybe my shooting is better or worse? At any rate let’s find out.
Starting off with my Chronograph test I was able to get an average 6 shot velocity of 348 fps which is about 40 fps less than my testing 6 years ago of 390 fps, perhaps the temperatures where a bit different? Perhaps the valve setups of the guns was not the same? By the way the temperature was 23 degrees Celsius in the indoor Airgun Sea Can Shooting Range and I was using a brand new 12 gram CO2 along with 5.1 grain zinc coated steel BB’s.
Moving on to the accuracy test, surely I would get a similar 1 inch 6 shot grouping from the Umarex Colt Python 357 Magnum Chrome CO2 BB Revolver, after all it’s been 6 years and I must be a much more advanced shooter… Well there again the Chrome Umarex Colt Python 357 Magnum CO2 BB Revolver did not perform as well as the black one from my 2014 Field Test? Again maybe the steel BB’s I was using where not of the same quality? Maybe I simply had one too many espresso shots? As the video shows this time around I was only able to get about a 2 inch 6 shot grouping from the Umarex Colt Python 357 Magnum Chrome CO2 BB Revolver. Still not bad but I was hoping for better result or at least the same as before.
I could do this test again and get completely different results using perhaps another brand of CO2 on a warmer day with higher quality Steel BB’s and just maybe with me on my game a little bit better? At the end of the day 350 fps is perfectly fine for putting holes in pop cans and a 2 inch group at 30 feet will get you on most targets every time so I’m not going to sweat it too much. If you are looking for a shell loading CO2 BB Revolver the Umarex Colt Python 357 Magnum Chrome CO2 BB Revolver is for sure one of my top picks.
Type: BB air revolver Manufacturer:Umarex. Model: Colt Python 375 Materials: Almost entirely all Metal. Weight: 2.75 pounds (1218 grams). Barrel: 5.5 inches, metal non-rifled. Propulsion: 12 gram CO2. Action: Revolver, single & double actions. Ammunition Type: 4.5mm steel BB's. Ammunition Capacity: 6 round cylinder. FPS: 400.
Trigger Pull: The trigger pull on the Umarex Colt Python 357 Magnum Chrome CO2 BB Revolver is good in both single and double action, it’s nice that you have the shorter lighter single action trigger for slower more accurate shooting but you can also blast away in double action when you feel like it. The hammer on the Umarex Colt Python 357 Magnum Chrome CO2 BB Revolver is firm with not very much wiggle which some other revolvers in this category do have.
Accuracy: Based on my results shooting the Umarex Colt Python 357 which is essentially the same gun in a different finish. The results I got shooting my 6 round group from a 30 foot out semi rested position where good overall. Vertically there was about a 2 inch spread while horizontally there was about a 1 inch spread. I did find the plastic tips on the brass shells seemed to be a bit tight at first and this is when I did most of my Chronograph and target shooting. I believe the tightness effected the consistency of the FPS which also effected the accuracy especially up and down. I did get one shot out of the Umarex Colt Python 357 well over the claimed 400 fps but again the fps was rather erratic most likely because of the snug BB fit due to shell break-in.
Build Quality: The Umarex Colt Python 357 Magnum Chrome CO2 BB Revolver being mostly metal has a very good build quality and is on par with the Dan Wesson 715 shell loading revolver. It has a nice weigth adn balance to it and feels really good in the hand! The only real plastic I could find was in the grips and the shell tips. Fit and finish was also good with no noticeable chrome wear or sloppy workmanship. It will be interesting to see how the Chrome finish wears over time compared to the black finishes fodun on most KWC made Airguns.
Realism: TheUmarex Colt Python 357 Magnum Chrome CO2 BB Revolver overall is a close copy a the real steel Colt Python 357 styled revolver. I did notice the rear portion of the receiver (between the rear cylinder and hammer) to be a bit longer perhaps to accommodate the CO2 valve length, but other than that, this pistol is super close to the original Colt Python 357 styled revolver it is based on. Again being all metal gives this CO2 BB revolver very realistic weight and feel and the loadable brass shells make using this gun almost exactly like using a real shell loading revolver but for much less cost per shot and of course a lot less recoil on the hands and noise to be had.
Pros:
Shells loading revolver give you the feeling of loading and shooting a real revolver.
Mostly all metal design.
Lots of detail, well made, chrome looks nice, not sure if it will wear better than the black finish found on most KWC made pistols?
Good overall weight, almost 3 pounds.
Should have good overall power, accuracy and shots per CO2 (based on my previous Colt Python testing).
Fully adjustable sights.
Well hidden CO2 Screw.
Recessed barrel.
Nice Trigger pull in both single and double action.
Cons:
Grips are a bit rough and wood grain is only OK.
Grips may be a bit large for people with small hands.
Decent enough Colt Python 357 replica but the frame is a bit long between the cylinder and the hammer.
Comments:
It’s been a while since I reviewed a Shell Loading Airgun and this one is pretty much the same Airgun I have reviewed in the past in both the KWC and Umarex Distributed forms. It has been almost 6 years since I took a look at one on my table and it still hods up today. I plan on performing another Field Test Shooting Review for the Umarex Colt Python 357 Magnum Chrome CO2 BB Revolver to see if I can replicate the same good results I did back in 2014 when I tested it out on my deck. If you’re looking for a shell loading revolver in the 357 design then for sure checkout the Umarex Colt Python 357 Magnum Chrome CO2 BB Revolver as an option.
My Vimeo Table Top Review for the Umarex Colt Python 357 Magnum Chrome CO2 BB Revolver:
Type: Pellet Revolver. Manufacturer: Gamo Model:PR-776. Materials: Mostly metal construction. Weight: 2.2 Pounds (1 kg). Barrel Length: 6 inches Total Length: 11.5 inches. Propulsion: CO2 x1 Action: Revolver single and double action. Ammunition Type: .177 caliber pellets. Ammunition Capacity: 8 rounds per magazine. Max FPS: 400+ fps.
Trigger Pull: The Gamo PR-776 CO2 .177 Caliber Pellet Revolver has your traditional revolver single and double action trigger setup. In double action, the trigger is going to be a bit longer and heavier but it feel fairly smooth with no real friction points and I would consider it to have a medium trigger pull. When you cock the hammer back placing the Gamo PR-776 CO2 .177 Caliber Pellet Revolver in single action, the trigger pull becomes very short with virtually no take-up at all and the weight of the trigger is very light allowing for more accurate shots.
Accuracy: Make sure to watch my Field Test Shooting video for the Gamo PR-776 CO2 .177 Caliber Pellet Revolver where I test out the velocity and accuracy in the Replica Airguns Indoor Airgun Shooting Range. In summary the Gamo PR-776 CO2 .177 Caliber Pellet Revolver shot a little bit hotter than claimed at just over 400 fps using around 7 grain lead pellets. In terms of accuracy with a total of 16 shots the grouping spread out to around 4 inches but I am pretty sure a different pellet choice may have made a difference.
Build Quality: The build quality of the Gamo PR-776 CO2 .177 Caliber Pellet Revolver is pretty good overall. It is mostly all metal with the exception of the grips of course, Fit and finishes looks good, everything feel snug adn tight with the exception of the pistol grips. I feel like the grips could easily move out of place and get caught on something. This is not a problem when shooting, more so when in a holster. The Gamo PR-776 CO2 .177 Caliber Pellet Revolver feels good in the hadn't, nice and solid and with a good weight to it.
Realism: The Gamo PR-776 CO2 .177 Caliber Pellet Revolver is a decent looking Airgun in the style of a traditional revolver, I wouldn’t say it’s an exact replica of any specific revolver in production but it does tick off all the boxes in terms of looking realistic. The weight and feel for now and the Gamo PR-776 CO2 .177 Caliber Pellet Revolver also has a recessed barrel and hidden CO2 crew. The only real giveaway would be the cylinder size as it is a bit smaller than expected and of course is chambered for .177 caliber pellets.
Pros:
Good power over 400 fps using actual lead pellets.
Quicker reloading over shell loading revolvers
More shots per magazine reload, 8 versus 6.
Comes with two metal 8 round magazines.
Traditional single and double action trigger.
White dot front sight with fully adjustable rear sight.
Good weight and feel to it.
Fit and finish look good.
Recessed barrel for realistic looking barrel opening.
Should be able to use a dovetail type scope mount for adding on a red dot or magnified scope.
Cons:
Not a fan of the loose pistol grip setup to access the CO2.
Was hoping to get a bit tighter grouping but may have been a pellet choice issue.
Comments: It was nice reviewing the Gamo PR-776 CO2 .177 Caliber Pellet Revolver as it was a bit different then most of today shell loading revolvers. I like that the Gamo PR-776 CO2 .177 Caliber Pellet Revolver still offered a realistic looking cylinder that the shell loading revolvers have but with the moon clip style magazines that allow for quick adn easy reloading of 8 rounds at a time. The velocity or power of the Gamo PR-776 CO2 .177 Caliber Pellet Revolver was even a bit high than Gamo claims using PBA Platinum pellets since Gamo claims 400 fps using these 5.1 grain lead pellets. My testing with closer to 7 grain pellets yielded fps up and over 400 fps. All the Gamo PR-776 CO2 .177 Caliber Pellet Revolver needs is to be just a little bit more accurate but I feel this may simply be more of a pallet choice, once you find a pellet the Gamo PR-776 CO2 .177 Caliber Pellet Revolver likes I am pretty sure it will deliver accurate shots.
My Table Top Review for the Gamo PR-776 CO2 .177 Caliber Pellet Revolver:
Make sure to watch my upcoming Table Top Review for the Gamo PR-776 CO2 .177 Caliber Pellet Revolver where I go over the specifications, pros and cons and show it up nice and close. In this Field Test Shooting Video I determine what the accuracy and velocity of the Gamo PR-776 CO2 .177 Caliber Pellet Revolver by testing out the fps with my Chronograph along with a accuracy test shooting a paper target at a distance of 30 feet away using a rested shooting position.
For the velocity test I placed a brand new CO2 Cartridge in the Gamo PR-776 CO2 .177 Caliber Pellet Revolver and shot five 6.9 grain lead pellets though my Chronograph. Gamo claims their 5.1 grain PBA Platinum pellets will shoot around 400 fps so I was expecting something in the low to mid 300’s but was surprised at a five shot average of 4115 fps with the much heavier RWS6.9 grain pellets. The slowest shot I achieved was 396 fps while the fastest shot was 434 fps. The temperature was right around 24 degrees Celsius or 75 degrees Fahrenheit.
For the next section of my Field Test Shooting Review I setup a brand new paper target 30 feet down range and loaded up two eight round magazines. The results for the Gamo PR-776 CO2 .177 Caliber Pellet Revolver where a bit confusing with both eight round magazines. It seemed like most of the shots wanted to group within about 1-2 inches of each other but I was getting several outliers that extended the grouping to closer to four inches. Not the best performance but as I have found with many guns, sometimes you need to find a pellet that the gun is happy with. the wrong pellet can really make a difference and I am fairly sure this was the case with the Gamo PR-776 CO2 .177 Caliber Pellet Revolver using the RWS pellets. just not the best choice for it.
The Gamo PR-776 CO2 .177 Caliber Pellet Revolver overall performer well, like I said I really think pellet choice will be the deciding factor in how accurate it is going to be. The velocity was very good for a CO2 Pellet revolver considering I was suing actual lead pellets and not the alloy pellets Gamo was using as their reference. The Gamo PR-776 CO2 .177 Caliber Pellet Revolver uses metal eight round magazines which are easy to preload and allow for two additional shots over the more common these days shell loading revolvers, which makes the Gamo PR-776 CO2 .177 Caliber Pellet Revolver more practical as a target pistol allowing for more power and easier loading.
The Umarex T4E TR50 .50 Caliber Paintball Revolver is an interesting Paintball pistol, it has a very different look and also uses .50 caliber Paintballs which are a little bit less common than the .68 and .43 caliber paintball gun I have been reviewing up until now. The Umarex T4E TR50 .50 Caliber Paintball Revolver is some countries is marketed as a self defense gun but those versions do have a little bit more fps and foot pounds of energy. The version I am testing is not marketed here in Canada or the US as self defense products but rather as more of a training Paintball Gun.
Starting with my Chronograph velocity test I placed 5 Rubber Balls through my Chronograph using a brand new CO2. The Rubber balls I am going to say are a little bit heavier than standard Paintballs and Umarex claims the Umarex T4E TR50 .50 Caliber Paintball Revolver is capable of hitting around 360 fps so with the heavier rubber balls I was expecting a little bit under the max fps. I was able to get an average of 328 fps so not bad at all.
Moving on to my accuracy test. I need up placing 10 of my 12 rounds into the paper target as I had two rounds that went off in what I am going to call an uncontrolled manor. The 10 rubber paintball rounds that did hit my paper target that was setup 30 feet down range all hit within about 6 inches of each other daily well centered left and right and a little bit low on the target. Gettin back to the uncontrolled shots, I had a situation where I pulled the trigger and the Umarex T4E TR50 .50 Caliber Paintball Revolver went click as you would expect but no CO2 was expelled and so no round was shot. I thought perhaps the cylinder was caught up so I went to wiggle it to try and free it up. As I did so the gun went off without my finger anywhere near the trigger. I am glad I was using rubber balls since the rubber ball hit my cabinet leaning a biota a mark but really causing any damage. This happened twice with the same cylinder, the second time I was bit more prepared for it and had the gun pointed well downrange. I was not able to recreate this problem again so perhaps the cylinder magazine was not seated properly but this still concerns me a bit.
Overall I really like the Umarex T4E TR50 .50 Caliber Paintball Revolver, it’s a pretty cool looking Paintball Gun with decent accuracy and power, you can even feel a little push back and barrel lift when you shoot it. I also like that you can preload a CO2 and puncture it whenever hypo are ready to shoot with a quick smack on the bottom of the grip. Just made sure to put the CO2 in the right way :)
My systems setup for a more powerful airgun as I was shooting .22 caliber lead pellets with about 11-12 foot pounds of energy. Direct hits passing through the 3/4 inch cut outs had no problem laying down the metal paddles and resetting the paddles was a lot easier than I though it would be even way back 50 feet.
I did not have my Sig Sauer Virtus PCP .22 Caliber Air Rifle perfectly sighted in so I did have to aim low and to the left which made it a bit harder dropping the plates but I did manage to get the job done at least for providing a decent test video fo the Rx Target Systems for the purposes of this video.
Make sure to not only watch my Field Test Shooting video included in this post but also checkout my Rx Target Systems Preview Video where I show it up and close and also go into more details on the Rx Target Systems and how modular and versatile it really is.
I want to thank David Bitkowski from Rx Target Systems for providing me with this sample unit to share with the Replica Airguns community. This video is only a Preview video as I wanted to get the RX Target System out there before I follow up with my actual Table Top and Shooting Videos for it.
For now here are some of the key points I want to get out to everyone:
Mission: Rx Target Systems are meant to bridge the gap between firearms and airguns. They allow high precision shooting on a reactive, three- dimensional, rugged target that can be carted around in a back pack. What makes Rx Target Systems unique is that it is a system. It is so modular and adaptable with interchangable faceplates and paddles. Rx Target Systems are not going to break or get dented or dissembled on the range as many of the lighter gauged steel targets on the market today vs today’s high powered airguns.
Modular
One base allows interchange of faceplates for different target configurations
One threaded axel allows interchange of paddle from 10 gauge to 3/8 inch-thick paddles
Portable
Mount it on a shelf indoors
Mount it on a sawhorse outdoors
Carry it in a backpack or duffle bag- its 10 pounds
Rugged
Solid steel design
Faceplates from 10 gauge to ¼ inch thick
3-Dimensional
Faceplate is offset from paddles
Clipping the aperture does not guarantee a score
Intentions of target configurations
Standard 1 inch bulls.- represents kill zone of many small game at 30 yards, great for sighting in prior to the hunt. Also is ¼ scale of bull used in rapid fire pistol when shot from 8.3 meters. (25 meters distance/100mm bull)
1.2 inch bulls- represents the 4-10 ring of the NRA 10 meter air rifle target. Gears the shooter to consistently hitting the “black” of that target on paper
AAFTA style- represents common kill zones found in American Airgun Field Target Assosciation using 1.5”, 1”, ¾", ½", and 3/8”.
WFTF style- represents common kill zones found in World Field Target Federation using 15mm, 25mm, and 38mm apertures
10-15- Inspired by customer request, uses 10mm and 15mm apertures. High-Precision shooting.
Unfortunately the microphone system I was using for some reason did not record the Lapel Microphones we where record the audio with for this ASG SHOT Show 2020 Interview Video. The Camera we where recording video with did record audio but as there is so much back ground noise going on at large show like this, the audio is far from good. That all said try do you your best to listen to what we are discussing. There are sections where the audio is fairly distinguishable and sections in the video that are not due the proximity of the camera.
Bob from ASG and I go over serval products for ASG at SHOT Show 2020 this year. We first take a look at the new ASG Shadow 2 CO2 Blowback BB Pistol. One interesting fact about the new ASG Shadow 2 is that it has an internal Hop-up system that help BB’s travel further out for longer range shooting. The ASG Shadow 2 also has a fully adjustable rear sight making this Blowback CO2 BB Airgun a potentially pretty decent target pistol.
Another new product from ASG we focused on is the Airsoft ASG B&T Universal Service Weapon designed for first responder situations. The ASG B&T USW has an extended rear frame allowing for a non-recipricating red dot sight placement. The ASG B&T Universal Service Weapon has a built in folding stock and you can trick it out with all kinds of add ons to make it your own.
Near the end of the video we took a look at some new ICS Airsoft offerings from ASG.
This isn’t a SHOT Show 2020 Interview but most certainly worth reporting on. While walking around SHOT Show I ventured into the Chiappa Booth as I own a .22 caliber 1911 styled pistol from them and they do have some interesting products to take a look at.
Then I saw a red tip on one of their Chiappa Rhino Revolvers which caught my eye since I was not aware that Chiappa was making an Airgun version of their Rhino. Well as it turns out they are hoping to be shipping both an Airsoft version and Steel BB version around spring time and from what I can tell there will be two finishes, a kind of Gold Satin finish and also a Back finish version. As is with a lot of revolvers these days they will be shell loading which will help them look the part of a real steel Chiappa Rhino Revolver.
Looking forward to getting my hands on one when they come out in Spring this year!
This year Sig Sauer was showcasing their Airsoft Pistols with a new line called the Proforce series geared towards high end training. Sig has also included new Reflex Red Dot Sights that can be ordered already on the gun or as an add on accessory. The Proforce Pistol line includes both the M17 and M18 series Sig Sauer pistols.
Last year at SHOT Show 2019 Sig had introduced their Virtus .22 Caliber PCP Semi Auto Rifle but it was not ready at that time. Well now the Sig Sauer Virtus is ready to ship and yours truly will be getting one of these bad boys for review! Since the .22 caliber PCP Sig Sauer Virtus shoots around 700 fps with a 12 foot pound energy level you will need a PAL firearms license if you live in Canada but the Sig Sauer Virtus is a considered a “long gun” so no registration will be required in Canada.
Watch my Sig Sauer SHOT Show 2020 Las Vegas Interview for more info and cool stuff presented by Stephanie from Sig Sauer.
Here we go again, another round of SHOT Show videos brought to you direct from Replica Airguns!
As always I like to start off with a Teaser Video with a few quick clips of some of the new products I had the opportunity to take a look at at this years SHOT Show 2020 Las Vegas.
I will be rolling out Interview Videos as quickly as I can edit them and put them together for the following Airgun Related companies:
Sig Sauer
Umarex
Crosman - Velocity Outdoors
ASG
Air Venturi
Chiappa
So sit back and enjoy this years Replica Airguns SHOT Show 2020 Las Vegas Teaser Video!
