Trigger Pull: The trigger pull on the Umarex HK G36 KVis fairly short and light as it is essentially just an electrical on off switch for the internal electronic components. You can shoot the G36 very quickly in semi auto mode, and in full auto it cycles very quickly giving a high rate of fire.
Accuracy: In my brief pre-testing without any sighting in, the Umarex Heckler & Koch G36 KV shot just a bit off center to the right from a 30 foot semi rested position and produced a nice 2 inch grouping. In full auto the grouping opened up a bit but still punched a nice 1.5 inch hole in the target with most of the BB hitting there.
Build Quality: The Umarex HK G36 KV is very well made, yes it has lots of polymer but so does the real version and the plastic seems very durable, the fit and finish looked great and there is a lot of metal in and around the G36 where it would be on the real steel gun and where it is really required to be. Like the trigger, top rail, pins, selector switch, barrel, gearbox and gears.
Realism: Similar to my WE G39C reviewed earlier, I bet if you had a real Heckler & Koch G36 sitting beside the Umarex HK G36 KV, you would be hard pressed to tell them apart? The Umarex is also fully HK licensed and trademark throughout even including the 5.56mm NATO markings.
Excellent attention to detail with lots of working parts.
All metal internals and metal external mechanical parts.
Semi auto & full auto selectable.
Full HK licensing and markings.
Accurate 2 inch 10 shot group from 30 feet out.
Nice high 450+ FPS.
Full ambidextrous, even the charging handle can be switched side to side.
High capacity magazine (400 rounds)
Built in 3x optical sight with ability to add a Red Dot for close quarter shooting.
4 position adjustable folding stock.
Easy access to hop up system.
Cons:
Does not come with a battery or charger.
Came with the orange tip, you may want to replace it or paint it black?
May be too powerful for close quarter skirmishes without some detuning.
Comments:
This is my first Umarex Airsoft rifle product review and I have to say it really seems good so far, I have not had a lot of hands on time shooting the Umarex HK G36 KV but right out of the box I was getting very good results, nice high 450+ fps and good groupings even out at further range. The fit and finish are all very good and the realism is as good, if not better than other Airsoft AEG I have reviewed. I like the built in 3x Optical Scope and the addition of an upper rail to accommodate a Red Dot, this gives you the ability to acquire quick close up shot placements using a Red Dot while also being able to focus in on further out targets using the magnified optical scope. I look forward to my official Field Test shooting review.
The Fenix models I show off in the YouTube video are the TK45 -TK15 - LD22 - PD22, a rather nice selection that should cover most lighting requirements.
Some Features and Benefits of Fenix Flashlights:
Use Top quality Cree XLamp XM-L LEDs for highest efficiency and LED lifespan.
Heat-sinks to make sure the LEDs do not overheat.
Use the Optic Ultra Clear Glass Lenses that also produce a perfect mix of Throw and Spill.
A constant current regulation circuit, which keeps the flashlights in constant brightness regulation. Unlike traditional flashlights output will not dim over the life of the battery.
Waterproof to IPX-8 (2 Meters) standard with Anti-shock.
Type III Hard Anodized Scratch Resistant Finish.
Fenix TK45:
760 Lumens
200 Meter Throw Beam
232 Hours Max Runtime
IPX-8 Waterproof (2 Meters)
Type III Hard-anodized Anti-abrasive finish
Impact Resistant
Fenix TK15:
337 Lumens
215 Meter Throw Beam
142 Hours Max Runtime
IPX-8 Waterproof (2 Meters)
Type III Hard-anodized Anti-abrasive finish
Impact Resistant
Fenix LD22:
190 Lumens
100 Meter Throw Beam
110 Hours Max Runtime
IPX-8 Waterproof (2 Meters)
Type III Hard-anodized Anti-abrasive finish
Impact Resistant
Fenix PD22:
190 Lumens
101 Meter Throw Beam
97 Hours Max Runtime
IPX-8 Waterproof (2 Meters)
Type III Hard-anodized Anti-abrasive finish
Impact Resistant
Make sure to watch my YouTube Video Preview on the Fenix line of Flashlights:
Materials: Mostly metal construction with a few plastic parts.
Weight: 2.1 pounds.
Barrel: 4.88 inches, metal non-rifled.
Propulsion: CO2 x 1.
Action: Semi auto blowback, single action only.
Ammunition Type: 6mm plastic Airsoft BB's.
Ammunition Capacity: 16 round magazine.
FPS: 400+.
Trigger Pull: The trigger pull on the G&G Xtreme 45 is very smooth in single action only mode with there being just a bit of take-up and then a fairly light release, the light blowback and single action trigger allow fast sequential shooting with good groupings.
Accuracy: This is somewhat yet to be determined in my upcoming Field Test Shooting portion of this review but I did get the chance to take it outside and put some rounds down range, performance overall seemed decent.
Build Quality: This is an almost all metal air gun with good fit and finish and a nice hefty 2.1 pound weight to it. very similar in build to the Umarex Colt Special Combat 4.5mm BB Pistol reviewed earlier! The only plastic parts to speak of are the grips. In a perfect world, real wood grips would be nice but I have feeling that real 1911 grips may just fit this gun?
Realism: The G&G Xtreme 45 is a very good replica of the classic 45 auto 1911 styled pistol, with the exception of the trigger mechanism. I was happy to see if had a single action only trigger like you would find in a 1911 so this was a bonus. Overall weigh and feel make this Airsoft pistol a very believable gun and the blowback although light gives some nice feedback when shooting and the allowable single action trigger on followup shot.
Blowback operation (enough to give it some shot feedback and also cocks the hammer for easy single action trigger pull).
High fps for a blowback Airsoft pistol.
Expect to get decent amount of shots per CO2.
Fully adjustable rear sight.
Attractive two tone finish.
Magazine is all metal full size and hold both the CO2 and BB's and has a flush hidden CO2 screw.
Rain for accessories.
Very affordable gun considering all of the features it comes with.
Cons:
Blowback operation is light and not a full cycle.
Slide catch does not engage on the last round.
Does not have a true 1911 styled trigger but at least is single action.
Comments:
The G&G Xtreme 45 CO2 Blowback Airsoft Pistol is a great combination of realism and practicality toped with lots of great features you don't often find in a gun in this price range: Almost all metal, blowback operation, good fps and CO2 usage, fully adjustable rear sight, full size drop out metal magazine with hidden tab, awesome looks, and low price point. If your in the market for a good all around 1911 styled Airsoft blowback pistol, definitely put this one on the check list!
My Vimeo Video Review for the G&G Xtreme 45 CO2 Blowback Airsoft Pistol:
Trigger Pull: The trigger pull on the Bolt Airsoft B4A1 is fairly short and light as it is essentially just an on off switch for the internal electronic components. You can shoot this gun very quickly in semi auto mode, and of course in full auto when full auto position is selected. As is with all AEG rifles there is a bit of a delay while the spring is retracted and released, this is not as noticeable in full auto.
Accuracy: I tested the B4A1 Airsoft rifle by putting around 10 rounds into a target from 30 feet with .36 gram Airsoft 6mm BB's while using a semi rested position (sand bag in the front - standing in the rear). I used a non-magnified red dot scope for this test rather than using the built in iron sights. I got very good result in semi auto and even with the recoil making my sights jump around a bit in full auto still stayed well centered on target and got about a 1.5 inch group in both semi and full auto. My chronograph testing with lighter .20 gram BB's resulted in a 421 fps 5 shot average.
Build Quality: The Bolt Airsoft B4A1 Metal AEG Carbine is very well made with a full Metal upper and lower receiver, along with metal and polymer parts exactly where they would be on the real steel version of an actual Colt M4. The only plastic or nylon components are the stocks and the grips and perhaps some internal parts. I found the adjustable stock and magazine tolerance to be tighter than my King Arms M4A1 I previously reviewed which showed the Bolt B4A1 had a bit higher quality in the workmanship, for the most part the fit and finish was very good!
Realism: As with many Airsoft guns, there is great attention to realism and the Bolt Airsoft BRSS B4A1 Carbine is another great example of an Airsoft Carbine based on the Colt M4 platform. It is an AEG but because of the BRSS (Bolt Recoil Shock System) you get a very nice compromise between a conventional AEG and a GBB (Gas Blow Back Airsoft) gun. In other words, like a standard AEG I get that endless stream of consistent BB's flying down range on target but unlike a true Gas Blow Back Airsoft gun, I don't get that drop off in power and limitation to about 30 usable rounds per magazine . What I do get similar to a GBB is that recoil action that helps make the shooting experience so much more believable! Even the sound from the Bolt B4A1 is much snapper than a standard AEG and more like a GBB. I also like the fact that the charging handle and forward assist work similarly to a real M4 and also the dust cover cleverly exposes the bolt and internal hop-up for easy adjustment along with the bolt cycling just like a GBB rifle would cycle which is similar to a real steel M4.
Great attention to detail with lots of working parts.
All Metal upper and lower receiver, lots of metal parts throughout.
Semi auto & full auto selectable.
High capacity 300+ round magazine.
Removable carry handle with Weaver/Picatinny rail underneath.
Nice high 420 real FPS.
Extremely accurate for plastic BB's.
Fully adjustable sights with two position Peep sights.
6 position adjustable stock.
Easy access to internal hop-up system.
Realistic Blowback Recoil system (BRSS) for a very believable shooting experience!
Cons:
May not get off as many shots per battery charge as a traditional AEG because of the Bolt Recoil Shock System.
Does not come with battery or charger but most higher end AEG's also do not.
Not yet readily available in Canada, maybe we can change that :)
Comments:
The Bolt Airsoft B4A1 Blowback Airsoft Carbine is a great compromise for the avid Airsofter looking for a practical skirmish weapon, but also craving the realistic experience of having blowback with recoil which up until now was really only provided by Gas Blow Back systems. I really like this concept and find it great fun to shoot even if its just for plinking in the yard. The overall quality is very good and you just have to love the M4 platform it's based on. If you're into customizing you can mix and match many external and internal parts with other existing Airsoft mechanical parts and I would imagine real steel accessories. I like mine as is with my addition of a riser and Red Dot and if I every get a chance to get out for a skirmish this will be my weapon of choice for sure!
I got a few sample products I wanted to quickly share with everyone :) First off Bolt Airsoft, a Taiwanese based company, sent me one of their B4A1 (M4A1 Copy) AEG Airsoft rifles featuring BRSS - (Bolt Recoil Shock System) which has Blowback with simulated recoil.
The Bolt B4A1 is designed after the M4A1 and looks and works like most AEG Airsoft rifles giving you sustained performance and the use of high capacity magazines but Bolt has added their BRSS - (Bolt Recoil Shock System) which gives you the feedback and recoil you would normally only get with a true GBB (Gas Blow Back) Airsoft gun.
I will be doing a full review very shortly so watch for it!
I also received from ASG (Action Sport Games) a few Mock Airsoft Suppressors, all of them are B&T (Brügger & Thomet) derivatives. It was nice that they sent me the version (MP9 QD) that fits perfectly on my ASG/KWA MP9. The other tow are the ROTEX-IIIA and ROTEX-IIIA Compact that fit perfectly on to a standard flash hider and even include one with them.
Check out my Vimeo Preview Video of these Review items from Bolt Airsoft and ASG:
As with most new items I pickup, I like to share them with everyone. I am checking into some more ROHM blank guns, an RG-59 and RG-88, the RG-59 is a lot like the ROHM RG-56 .22 caliber blank revolver I sell in the Canada Replica Airguns Store but in .380 caliber and the one I show off here is a 5 shot two-tone model. Other than that they use the same frame and mechanical parts throughout.
I also received a black/blued ROHM RG-88 which is kind of like a Walther PPK in design, it field strips the same, has a similar safety setup and even has a similar size and look to it although it is definitely not a replica of a Walther PPK. I am impressed with the overall quality of the ROHM blank guns, material used, fit and finish is very good.
Lastly, I acquired a pre-owned Umarex CP99 CO2 Pellet Pistol from a customer of mine. It is in pretty much in new condition and is one of the Umarex guns I was missing in my collection and have been looking to add. The Umarex CP99 is a pretty good replica of the Walther P99 and uses the standard Umarex metal 8 shot rotary magazines and shares the same CO2 grip fed magazine as the CPSport. The CP99 is German made so it's not one of the lower cost Umarex pistols out there but you do get what you pay for ;)
I've had lots of requests to review the Daisy Winchester Model 11 and to give my opinion how it stacks up with the Cybergun Tanfoglio Witness 1911. I will be doing a full review of the Daisy Winchester Model 11 Colt 45 1911 replica shortly but wanted to kick things off with my comparison portion.
Your best off to simply watch my Vimeo Video Comparison of the Tanfoglio Witness 1911 and Winchester Model 11 but here are my thoughts on some of similarities, strengths and weaknesses for both 1911 syled airguns.
Similarities:
Both are good replicas of the classic Colt 45 1911 semi auto pistol.
Both shoot 4.5mm Steel BB's and use standard 12 gram CO2.
Both are mostly metal and weigh close to 2 pounds with the Cybergun Tanfoglio Witness weighing about 40 grams more.
Both come in a nice cardboard box.
Both have blowback operation with slides that lock back after the last shot.
Both have true 1911 styled single action only triggers.
Strengths:
The Winchester Model 11 has the higher feet per second rating and gets more shots per CO2 (410fps vs 320fps).
The Tanfoglio Witness 1911 has a full size drop out metal magazine that holds the BB's and CO2.
The Winchester Model 11 is more economical to buy and shoot.
The Tanfoglio Witness 1911 has a more realistic "full" blowback operation.
The Winchester Model 11 has less intrusive warning markings on the slide.
The Tanfoglio Witness 1911 has a working Grip Safety.
The Winchester Model 11 is made in Japan.
The Tanfoglio Witness 1911 can be field stripped similar to a real 1911.
Both have fairly high capacity magazines (16 BB's for the Winchester and 18 BB's for the Tanfoglio).
Weaknesses:
The Winchester Model 11 has a funky extra button on the thumb safety?
The Tanfoglio Witness 1911 tends to use a lot of CO2 with less average fps.
The Winchester Model 11 has more free-play (wiggle) in the slide.
The Tanfoglio Witness 1911 magazine are more expensive and can be hard to find at times.
All in all I really like both guns, and what really counts is how they feel and shoot and after a quick outside testing with the Daisy Winchester Model 11, it seemed to shoot and work pretty good for me. Realists may prefer the Cybergun Tanfoglio Witness 1911 because it is more realistic in terms of how it's built and how it functions but as a daily shooting gun, the Daisy Winchester Model 11 hits harder and gets more shots per CO2, all while still giving the shooter a very realistic 1911 styled shooting experience.
Watch my Vimeo video Comparison of the Daisy Winchester Model 11 vs the Cybergun Tanfoglio Witness 1911:
This is a much different review than I generally do but I have been using POV (Point Of View) or Action Cameras for some time now that I sometimes mount on my guns or myself for that first person style video angle. In the past I have been using an Innovations Drift HD170 Action Camera and an Oregon Scientific ATC9K HD Action Camera. I still have the Drift HD170 but the ATC9K went back to Costco because some of the plastic was starting to crack on it.
Let's turn the focus back to the Sony HDR-AS15 POV Action Cam, so why the "upgrade"? Well for one I had some extra play money because Costco gave me back all the money I spent when I returned the ATC9K. Of course there are a lot of other great cameras to choose from out there and I was considering one of the Hero based systems but the Sony HDR-AS15 POV Action Cam kind of caught my eye for a number of reasons.
Built in WiFi and with downloadable App for iOS and Android based Smartphones.
Comes with waterproof case good down to 60M (about 200 feet).
Has SteadyShot image stabilization that is very effective.
Carl Zeiss Lens with 170-degree or 120-degree selectable viewing angles.
Full 1080P 30fps resolution along with 720P 120 fps Super Slow-mo.
Excellent video and audio quality.
One of the most intriguing features for me was the built in WiFi as it allows me to see what the camera sees by streaming the video to my iPhone in real time. Even with a built in video view finder on a camera, you still can not see the screen when the camera is mounted on your head, while a remote screen using WiFi to stream the video to another device like my iPhone lets me see exactly where the camera is pointed and also start and stop recording and even change some of the settings remotely.
After doing some online research and watching video samples of the Sony HDR-AS15 POV Action Cam in comparison with some other very good quality Action Cameras, it was clear to me that the sony had excellent video and audio recording capabilities and seemed to even beat the competition in low light situations.
Of course there where some Cons I had to consider but for me they where not a big deal:
When in the water proof case you can only access the start and stop button.
No audio in any of the 720p high frame rate modes (60-120 fps).
It's a new product from Sony so there may be some bugs to work out and features that could be improved or added.
A bit limited in what camera mounts come in the box.
Your best bet to really see what the Sony HDR-AS15 POV Action Cam can do is to watch my video review for it. I show you around the Sony HDR-AS15 and also sync it to my iPhone using the PlayMemories Mobile Smart Phone App so you can see how to pair it, start and stop recording all while viewing the streaming video on the iPhone's screen. I also show you how you can use the WiFi feature to copy pre-recorded video from the HDR-AS15 to a Smartphone using the PlayMemories Mobile Smart Phone App.
I end off my review by showing you some video samples I made in various shooting modes and situations playing around with my new Sony HDR-AS15 POV Action Cam.
Checkout my Video Review of the Sony HDR-AS15 POV Action Cam:
Trigger Pull: The trigger pull on the ASG/KWC MP9 A3 is single action only as the charging handle has to be pulled back to open and release the bolt for the first shot. There is a trigger safety but it is not noticeable when shooting this Airsoft machine gun. There is a short take-up and then a light release and short reset.
Accuracy: Right away I put my NcSTAR 1x25 Red Dot sight on the ASG/KWC MP9 A3 as it was a perfect fit for this small and compact machine pistol, it did not take long to sight it in and I was able to get decent accuracy in both semi auto and full auto burst due to the mild but very fast cycle rate. I was able to get a 2 inch grouping at 30 feet out using a rested position. In full auto mode the grouping did not really get too much wider. I also got between 350 and 370 fps when testing the ASG MP9 on my Chronograph.
Build Quality: The ASG/KWC MP9 A3 Airsoft Machine Pistol is built very well, using similar components that you would find on the real steel version so yes it has a plastic shell but that is to be expected. The ASG/KWC MP9 A3 does use lots of metal where it needs to be like in the internal parts, pins, bolt, barrel, rails and even the magazine. The fit and finish is near perfect!
Realism: I have to say the ASG/KWC MP9 A3 is pretty much a bang on copy of the real steel Brügger & Thomet MP9 A3. The only telltale sign is the ASG branding on the right side along with the 6mm caliber beside the ASG logo. One other small detail is the magazine which is metal on the Airsoft version where as you would find the real version uses a transparent polymer magazine.
Rate of fire is very fast and does not slow down much even when the gas is running low.
Good overall power for a short barreled gas blowback gun.
Very nice trigger with working trigger safety.
Excellent replica of the real steel version in just about every way.
Can add a lot of gear and make this gun your own.
Decent price for all you get out of the ASG MP9!
Cons:
Bolt didn't lock back for me when the gun got really cold?
Real magazine would actually be transparent polymer.
Comments:
I really like the ASG/KWC MP9 A3! I love the look, I love the features and the price is also really good for what you are getting. I was really impressed with the super high cycle rate and because of the small low weight bolt the gun does not move around too much or slow down in rounds per minute even when you do a full mag dump. There is however just enough blowback recoil to give you that GBB realistic feel! I also found that the magazine holds a lot of gas so it is possible to get two magazine worth of shots out of a single fill, that's around 100 shots. I also like how easy it is to add to the ASG/KWC MP9 A3, I had mine pimped out and looking amazing right away and suggest if you get one you do the same :)
My Vimeo Video of the ASG/KWC MP9 A3 Airsoft Machine Pistol:
Take aim and fire with "The gun that helped to change the world". The Thompson Military M1A1 AEG is a battlefield weapon with a serious attitude. This beautiful gun is a fully licensed 1:1 scale replica of a real Tommy gun, and features a full metal body with artificial wood grain finish, a 60 Rd plastic magazine, and a shot velocity of 500 fps (using .20g BBs). The M1A1 also features an adjustable BAXS System for increased power and shooting accuracy. Airsoft enthusiasts will love the stunning classic era looks and awesome semi/fully automatic firepower of the Thompson Military M1A1 AEG. Do not miss this gun! Recommended for use with high quality .25g BBs.
Model:ME Ranger (1873 Colt 45 Single Action Army).
Materials: Mostly Metal with wood grips.
Weight: 2.2 pounds.
Barrel: Cylinder venting with fully plugged barrel. (No Red Tip)
Propulsion: Gun powder.
Action: Single action only.
Ammunition Type: .380 Crimped.
Ammunition Capacity: 6 rounds.
FPS: N/A.
Trigger Pull: The trigger pull on the Bruni ME Ranger Colt 45 Single Action Army Revolver is very light as it is a single action revolver and most of the effort is done by pre-cocking the hammer. All you are doing is releasing the hammer which with the ME Ranger is nice and light with next to no creep.
Accuracy: NA.
Build Quality: The overall build quality of the Bruni ME Ranger is nice an believable. It has good weight to it and the finish is not perfect but you would not expect and Single Action Army styled revolver to be perfect. All the mechanical parts felt tight and functioned perfectly for me.
Realism: The Bruni ME Ranger Blank Revolver is a pretty decent replica of a real Colt 45 Single Action Army Revolver in terms of size, weight and most general appearances. It does lack the 45 caliber larger more open Cylinder holes as it is chambered in .380 caliber but you can only see this when looking from the forward position of the ME Ranger. My version also had the plugged barrel so all flame and gasses emit from between the cylinder and the back of the barrel, it would be nice to un-plug this barrel so some of the gasses and flame would come out the front of the barrel.
Purchase from: A private collector.
Pros:
Well made, materials fit and finish is all very good.
True to the original 1873 Colt Single Action Army Revolver.
Real wood grips.
Nice light single action trigger.
Made in Italy.
Cons:
Not fornt venting.
9mm P.A.K. blanks do not fit - too long.
Wood grips are a bit bland.
Comments:
As my first replica Old West Single Action Blank Revolver, it is a nice addition to my collection. It would make an awesome prop for any cowboy or cowgirl costume, maybe I can convince my wife to go as a cowgirl this year for halloween ;) Overall I really like the Bruni ME Ranger and I plan to perhaps open the barrel up so that I get a more realistic shooting experience with flames and smoke coming out the front of the barrel. That and perhaps some work on the grips to give them a more rugged and weathered look.
My Vimeo Full Video Review for the Bruni ME Ranger Blank Revolver:
Trigger Pull: The trigger pull on the WE G39C is about what you would expect from a Single action only Semi Auto rifle, it has a very slight take up and then about a 4 pound trigger pull that is crisp and smooth.
Accuracy: Out of the Box the WE G39C shot great up close and farther out, the hop-up seemed to be already dialed in, and even though I was using only .20 gram BB's which is a bit light for this gun, I still found they tracked well and stayed on target both near and far. My 30 foot semi rested testing produced a nice 2 inch grouping. Shooting the barrel out on the tactical range I did have to aim just a bit higher when back out at 60 or more feet away. Maybe a slight bit more hop-up would do the trick.
Build Quality: The WE G39C is very well made, yes it has lots of polymer but so does the real version and the plastic seems very durable, The fit and finish looked great and there is a lot of metal in and around the G39C where it would be on the real steel gun and where it is really required to be. Like the trigger, flash hider, rails, pins, switches, rear sight, magazine and most internal parts also.
Realism: I bet if you had the real G36C sitting beside the WE G39C you would be hard pressed to tell them apart? WE did a great job making this Airsoft version very believable not just in appearance but also when field stripping it and shooting it with it's heavy bolt and felt blowback recoil.
Amazing attention to detail, just like the real H&K G36C.
All metal internals and metal external mechanical parts.
Semi auto & full auto selectable.
Awesome blowback kick really hits you in the shoulder.
Field strips just like the real steal version.
Nice high 400 FPS and good accuracy near and far.
Full ambidextrous, even the charging handle can be switched side to side.
Can get up to three magazines per propane fill up.
Very well priced for how awesome it really is.
Cons:
Some people may not like that it is a polymer built gun externally but it is what it is!
And that's it!
Comments:
So far I have been impressed with We an Airsoft company, they really know how to make very realistic and high quality products. I wasn't sure if I was going to like the mostly polymer external build on this gun but the sheer quality and solid build took away any ideas that tis Airsoft gun would be anything like a toy. The WE G39C is one of the best performing GBB Airsoft guns I have tried out getting up to 90 shots per gas fill on a magazine which is very impressive. We was also able to keep the price down which means more people can get into one of the G39C's. If you've been thinking about adding one of these to your arsenal I don't see any reason why not to!
Action: Semi auto, single & double action with blowback.
Ammunition Type: .43 caliber paintball or rubber bullet.
Ammunition Capacity: 9 round magazine.
FPS: 250-300fps.
Trigger Pull: The trigger pull on the Real Action Paintball RAP4 X50 is rather nice in single action, being a true blowback gun, the cycling of the slide not only chambers a round but also pre-cocks the hammer allowing for a very smooth and light single action trigger pull. There is also a working de-cocker that allows you to release the internal hammer. Double action is noticeably heavier but would only really be used on the first shot if you had already used the de-cocker.
Accuracy: After my previous review of the RAM X50 I was expecting this gun to perform pretty much the same. I did find it to be a bit more accurate within the 20-25 foot range using the rubber balls but when I got out into the field and switched over to the Paintballs I found that they where really hooking and darting all over the place? Mind you, this gun was right out of the box and not broken in yet. I also got a bit lower fps (right around 250) out of the RAP4 RAM Walther P99 compared to my RAM X50 but again my review unit had not been adjusted in any way and I imagine I could turn it up a bit to get more fps out of it if I wante to. The plus side is I was able to get an astounding 8 magazines worth of shots out of one CO2.
Build Quality: The RAP4 RAM Walther P99 styled Paintball Pistol is built very well, it does have a polymer frame but the gun overall has lots of metal parts and a very good overall 2 pounds weight to it dry. The blowback action is very snappy and all the mechanics and fit and finish all look and function very nicely. The slide spring is nice and firm giving this paintball gun a snappy recoil and the feel closer to a real gun than that of an airgun.
Realism: The RAP4 RAM Walther P99 was primarily made to simulate real word shooting environments for Police and Military users and even includes Walther branding and licensing, it is a very believable looking and functioning copy of the real steel semi auto pistol it replicates. Other than the exception of the CO2 Cylinder hanging a bit far out of the bottom of the handle. The RAM P99 would be hard to tell from the actual Walther P99, especially when looking down the large .43 caliber barrel. The Blowback action and firm recoil help pull off the believability when shooting this ralistic Paintball Pistol.
Very Accurate Walther P99 replica including licensing and trademarks.
Everything works pretty much like the real gun so a great training tool.
Good accuracy up close and lots of shots per CO2 for such a large round.
Nice light single action trigger and working de-cocker.
Fairly affordable.
Cons:
CO2 cylinder sticks out from the handle and looks a bit odd.
Paintball accuracy out at range was unpredictable.
Does not field Strip conventionally.
Comments:
This was my second time testing a RAP4 RAM product and again I took the chance to use it as it was intended to be used - in the field going through simulated tactical situations. My targets where barrels this time but they could have been other people with similar paintball guns shooting back at me which would have put even more pressure on me and forced me to really see where my mistakes are being made. That's the whole point of this type of training airgun, make it as real as it can be without your actual life being in danger so that when you are in danger you will not have to think about what you are doing but simply react based on your previous training. I think anyone who is a gun owner wanting to improve their reactive shooting skills should invest in one of these Paintball guns. One day you may thank yourself but let's hope it does not come to that!
Photo of Mystery KSC Removed by Request from Glock "Renzulli Law Firm"
All references, photos and video claiming that any item in this Review/Video looks like a Glock or is a Replica of a Glock in any way shape or form have been removed from this post as requested by Glock"Renzulli Law Firm"
Type: Airsoft GBB pistol. Manufacturer: KSC? Model: NAME REMOVED 17. Materials: Plastic & metal. Weight: 1.6 pounds. Barrel: 4 inch, non-rifled. Propulsion: GBB - Propane. Action: Semi auto - single action only. Ammunition Type: 6mm plastic Airsoft BB's. Ammunition Capacity: 23 round drop out all metal magazine. FPS: Up to 330. Trigger Pull: The trigger pull on this Mystery NAME REMOVED 17 GBB Airsoft pistol is very nice with some take-up at the beginning but once you hit the resistance part it is smooth and the release is very light. The NAME REMOVED trigger safety actually works on this model which is a nice touch!
Photo of Mystery KSC Removed by Request from Glock "Renzulli Law Firm"
Accuracy: I found the (KSC) NAME REMOVED 17 to have very good accuracy, getting about a 2 inch 8 shot grouping from 20 feet out in a semi rested position (sand bag up front, standing in the back). I also put 5 rounds through my Chrony Chronograph and this Airsoft Gas Blowback pistol averaged right around 326 fps using .20 gram 6mm plastic Airsoft BB's.
Photo of Mystery KSC Removed by Request from Glock "Renzulli Law Firm"
Build Quality: The (KSC) NAME REMOVED 17 Airsoft pistol uses a combination of plastic and metal and has a decent overall weight and feel to it thanks to the full size drop out metal magazine. The frame like a real NAME REMOVED is plastic but the slide and outer barrel are also plastic which on real steel NAME REMOVED would not be the case. Even so the overall weight is good and the fit and finish is very good. Even though this is a pre-owned Airsoft gun it is in as-new condition and seems to be holding up very well.
Photo of Mystery KSC Removed by Request from Glock "Renzulli Law Firm"
Realism: The (KSC) Airsoft NAME REMOVED 17 is very realistic in appearance and operation with all parts working exactly as they would on a real NAME REMOVED 17. Even the trigger safety works and field stripping this Airsoft gun is the same as a real NAME REMOVED. NAME REMOVED trademarks are present throughout, the only real giveaway is the plastic slide and outer barrel but you would need to examine this gun close up to see this for yourself. Purchased privately, check out some other Airsoft guns in theReplica Airguns Store.
Photo of Mystery KSC Removed by Request from Glock "Renzulli Law Firm"
Pros:
Very realistic and accurate licensing.
Got a tight two inch group but was a bit low, hop up should get it back up.
Decent FPS for a short barreled GBB Airsoft gun.
Even thought the frame and slide are polymer, it has good weight to it.
Everything works like the original, field strips and most mechanical parts are metal.
High capacity 23 round full size drop out metal magazine.
Adjustable rear sight for windage but is a bit lose on mine.
Good usage of the gas - two full magazines.
Photo of Mystery KSC Removed by Request from Glock "Renzulli Law Firm"
Cons:
Hard to get here in Canada.
Mostly plastic main build - slide and outer barrel are plastic.
Rear sight was a bit lose.
Comments: I am hoping that someone will know for sure who make this Airsoft NAME REMOVED 17 but either way it has been great playing around with it and doing my research to see if I could find out on my own. It's hard to tell you to go out and get one because I'm not sure what to go out and get at this point or even if this version can still be purchased and if so where from? All these questions... I can tell you that it's great to finally have an actual NAME REMOVED replica in my collection, I have a few NAME REMOVED-like guns but until I got my hand on this Mystery NAME REMOVED 17 GBB Airsoft pistol I really only had close proximities. So if you have the opportunity to snatch up something like this I say go for it!
Photo of Mystery KSC Removed by Request from Glock "Renzulli Law Firm"
Watch my YouTube Full Video Review of this Mystery NAME REMOVED 17 Airsoft Pistol:
Trigger Pull: The trigger pull on the Crosman 357 is decent in both single and double action. Single action is much shorter and lighter but not overly light with just a very short break to it. In double action it does get heavier and much longer as is expected. People with small hands may have to adjust their grip so they will have enough extension for the entire trigger pull, this is partially because of the larger grips that sit far back on the revolver frame.
Accuracy: I found the Crosman 357 pellet revolver to have excellent accuracy, getting about a 1 inch grouping from 30 feet out in a semi rested position (sand bag up front, standing in the back). I also put 6 rounds through my Chrony Chronograph and the Crosman 357 averaged 402 fps using RWS 6.9 grain lead pellets.
Build Quality:The Crosman 357 CO2 Pellet Revolver uses a combination of metal and plastic and has a good overall weight and feel to it. There could be more metal (like in the outer barrel) but Crosman used metal parts where they really needed to be like in the main frame, trigger, hammer, CO2 area and inner barrel. This air pistol has been around for a long time and so you can count on all the bugs being worked out. You will not find a great amount of detail in the Crosman 357 and some of the joints seem a bit unrefined but overall it is a nice looking airgun and feels well made.
Realism: The Crosman 357 is a replica of the Colt Python 357 Magnum and overall looks similar in shape. I would have liked to have seen a full swing our cylinder but this would have meant a complete redesign and the Crosman 357 main design goes back to the early 80's. Yes there are some newer revolver styled airguns like the Dan Wesson that have full swing out cylinders (BB only) but I still would have liked to have seen this, maybe on a future updated revision?
Inexpensive Pellet revolver, not really any other pellet revolvers out there to compare to.
Good usage of metal parts. (Metal trigger, hammer, frame, barrel, CO2 tab screw).
Single and double action trigger.
Excellent accuracy and good power with a reasonable amount of shots per CO2.
Can mount optics on the dove tail railed barrel.
High capacity 10 round removable magazine.
Fully adjustable rear sight.
Cons:
Outer barrel is plastic.
Grips and trigger pull length may be a bit long for smaller handed people when shooting in double action.
Some of the finish detail could be better (seems).
A slight recess on the inner barrel would have added to the realism.
Comments:
Reviewing this fun Crosman Pellet revolver was a bit of a walk in the past for me. back when I was in my early teens I had one and it went with me on just about all of my back woods adventures. I'd have to say I learned how to shoot with this pistol and it felt right at home back in my hands after all these years... Back in the day I didn't do any scientific testing with my Crosman revolver but I can tell you it shot hard and true then, just like it does now! I'm not sure why I held out so long getting another one, the price is right and if you are looking for a nice multi-shot pellet pistol with excellent accuracy and good power for well under $100, the Crosman 357 might just be for you.
I first want to say this isn't exactly a review, more of an overview. I do show you around this Chinese made Norinco Type 54 Model 213 9mm Tokarev copy but I don't shoot it or even talk too much about shooting it. I have shot my Norinco M213 and it's quit nice, especially when you consider this gun was designed back in 1930. The Original Russian made Tokarev was built to replace the aging Nagant M1895 revolver that the Soviet troops used as their sidearm.
The Tokarev looks a lot like the Browning FN Model 1903 and was more than likely based off of it but it is different internally utilizing a short recoil dropping barrel similar to what is used in a 1911. The original Tokarev was not normally chambered in 9mm but rather the Russian made 7.62mm round. Being that the original 7.62 round is longer than a 9mm Lugar, Norinco had to place a block inside the magwell to accommodate the smaller magazine. I think it's a good tradeoff so I can use my readily available 9mm rounds in it. Each magazine hold 7 rounds as they are single stack design, this does make the profile of the entire gun very slim.
Another feature to note, that is found on the Chinese Norinco Type 54 Tokarev copy is the addition of a safety. The original Tokarev did not have a safety on it. The safety is similar to what you would find on a Makarov.
I have several Norinco guns and from what I have seen, people either love them or hate them and it's usually the people that own them that love them and the people that don't own them that don't like them. This may be based on first impressions as many Norinco guns are not as refined as what you would see in a Smith & Wesson, Sig Sauer and many other higher end firearms. With that said the Norinco firearms kind of remind me of many Russian made guns which are more about how they work and less about how they look. The Norinco metal is tuff as nails and has a very high nickel content in it which is what makes it harder to refine.
Even today the Tokarev is a decent gun and I really love the history behind it, once you get used to it's unusual looks it really does start to grow on you and you can pick one up for pretty cheap these days, I only paid just over $200 for mine and it even came with 4 magazines.
Watch my Vimeo Video Overview of the Norinco Type 54 Model 213 9mm Tokarev:
Materials: Mostly metal with minimal plastic parts.
Weight: 2.1 pounds.
Barrel: 6.9 inches, metal rifled.
Propulsion: Spring-piston-operated.
Action: Single shot.
Ammunition Type: .177 & .22 caliber pellets.
Ammunition Capacity: 1 pellet.
FPS: 400-499.
Trigger Pull: The trigger pull on the Webley Tempest is very good, being that it is single action, there is next to no take-up and the pull itself is very light, yet not so light that you would accidentally shoot the gun. This helps a lot with accuracy. And to top it off, you can even adjust the trigger pull weight to your liking from 3-5 pounds!
Accuracy: Being that the Webley Tempest is a spring piston design, there is a noticeable amount of felt recoil when the spring snaps backwards, and I say backwards because it compress towards the front of the gun. With many spring piston rifles the spring snaps forwards almost giving a reverse recoil effect. The Webley Tempest recoil hits you in a familiar direction which made the airgun feel a bit more natural and I believe helped me to get a nice 1.5 inch 5 shot grouping from 30 feet out in a semi rested position. I also got a 400 fps average rating form my .22 caliber 11.9 grain RWS pellets which took me right up to the Canadian limit of 5.7 Joules to stay just within the limits of the uncontrolled firearm status for an airgun. FEW!
Build Quality: Build quality is very good, most of the gun is all metal with a few plastic parts, basically the nose cap and hand grips, everything else is metal on the Tempest. The Webley Tempest has a nice compact size for a spring piston design and has a nice weight to it making it feel very solid but not overly heavy. I do have to say the cocking effort is very heavy and you will have to try a few different techniques until you find a way that works for you.
Realism: This is not a replica airgun so to speak of but the basic pistol grips and trigger are designed to replicate a revolver more than anything. The Tempest is very unique and its basic design roots go back to the 1920's.
Fully adjustable rear sight for windage and elevation.
Small and compact yet very effective power.
Trigger pull adjustable from 3-5 pounds.
Cons:
If you're left handed the grips will not be as comfortable for you.
Sight adjustment will take some time to get right.
Spring recoil takes some getting used to so practice - practice - practice.
Cocking effort especially on the .22 caliber model is very heavy.
Comments:
Some people may qualify the fact that this "new version" is now made in Turkey but with that said I have been selling the Turkish made Webley Alecto for some time now and it has been one of my most trouble free airguns in the web-store. The Tempest looks to me to be just as well made and a nice perk with the Turkish made Tempest is its jump in velocity with the .22 actually hitting 400 fps and the .177 getting right around 500 fps, not bad at all for a fairly short barreled pistol. I also really like the small size this airgun has, it's no larger or heavier than say a Beretta 92 yet somehow it has to cram all the mechanics for the spring piston design into it and still get good performance. The only real reason I would not recommend this gun to some people is if you are of slight build or perhaps have some hand or wrist problems because it does take some effort to cock this gun, if this is a factor for you, you may want to go with the .177 caliber version as it does have a lighter cocking effort.
Action: Blowback, Single action only on KP-07 - Single/Double action on KP-02 & Elite 1A
Ammunition Type: 6mm plastic Airsoft BB's.
Ammunition Capacity: 20/22/20 rounds.
FPS: 366+ fps.
Trigger Pull: The trigger pull on all of these KJWorks Airsoft guns is very nice in both single and double action, The KP-07's true single action only 1911 trigger is a beauty, with no take up at all and a very light and smooth release. The Beretta Elite 1A is the next best with a surprisingly light weight double action trigger. All of these guns will be shooting primarily in single action as the blowback precooks the hammer with each shot.
Accuracy: I shot all of these fine KJWorks Airsoft guns from 20 feet out in semi rested position and got very similar results. I was able to place 10 rounds in a 2 to 2.5 inch grouping for all guns, with the KP-07 1911 shooting the most well centered. The Beretta Elite 1A shot well centered also but just a hair under center mass while the KP-02 seemed to shoot low but could be adjusted to shoot higher by increasing the hopup. All three KJWorks Airsoft pistols got right around the 330-350 fps mark (5 shot average chrony testing) with the KP-7 1911 and Elite 1A Beretta hitting the higher end and the KP-02 Sig P229 getting right around 330fps. All three KJWorks Blowback Airsoft guns should be able to hit 366+fps in the right shooting conditions.
Build Quality: I was extremely impressed with the build quality of these KJWorks Airsoft guns, the fit and finish is the best I have seen on any of my guns including Airguns also. Even after shooting several magazines worth of BB's, the painted metal friction areas did not seem to show nearly as much wear as some of my other blowback guns. The tolerances between the moving parts like the slide and frame are very tight showing excellent workmanship and machining with these KJWorks Airsoft guns.
Realism: All of these KJWorks 6mm Airsoft pistols are based on real steal versions of the same guns (KP-02 is a Sig Sauer P229 copy, the KP-07 is a Colt 1911 copy and the Elite 1A is a Beretta Copy). They are very good replicas even though the KP-02 and KP-07 do not have any specific licensing on them. The Elite 1A does have licensing which is a plus. The only negative thing I can think of is the fact that the KP-02 has the rather unusual CO2 magazine that sticks out of the bottom of the handle that is not at all like a real P229 magazine. I do believe you can find a GBB magazine that would be much more in line with the real steel version of this magazine.
All metal guns with good overall realistic weights.
Very heavy blowback on all guns, especially the KP-07 1911
Excellent fit and finish - best I have seen.
Nice mid range fps - great for on the field.
Very consistent accuracy for all KJWorks Airsoft guns.
Very believable replicas of the real steel versions.
Cons:
KP-2 and KP-07 did not have official licensing.
All seem to go through CO2/Gas fairly fast.
KP-02 had a rather strange looking CO2 magazine.
KP-02 slide did not lock back after last shot, may be due to CO2 magazine configuration.
Comments:
I guess you get what you pay for, these KJWorks Airsoft guns do fetch a bit higher price but when you take them out of the box and really look at them closely you can see why, they are pretty much flawless and the fit and tolerances are very good with very little play in the mechanical parts. Shooting these guns is just as wonderful, they all worked very well and got consistent accuracy and fps between shots. There where no ammo loading problems and no unexpected behaviors with any of these Airsoft pistols. If you can afford to pay that little bit more for one of these very high quality KJWorks Blowback Airsoft guns, you will not be let down!
Trigger Pull: The trigger pull on the Umarex HK P30 is fairly nice in single action mode while shooting in double action will give your trigger finger a bit of a workout. You can fire off pretty quick in double action but not as fast as with airguns that have a lighter double action.
Accuracy: I shot the Umarex HK P30 at a target from 20 feet away in a semi rested position using both pellets and BB's to see how both ammunitions worked. I was also interested to see if pellets would perform better than the BB's? Using 6.9 grain RWS pellets I was able to get just over a one inch grouping close to the center of the target and also averaging 363 fps with my 5 shot chronograph testing. BB's did get higher chronograph results as expected with an averaged 415 fps but grouped a bit larger at just under two inches.
Build Quality: This is an extremely well made metal and polymer air pistol with great fit and finish and a nice dense 1.7 pound weight to it. It's another "made in Germany" Umarex that uses the 8 shot rotary pellet magazines but with teh added ability to shoot BB's loaded in the full size drop out magazine? There is plastic on this air pistol but it's in the same places you would find it on the real steel HK P30. The balance, ergonomics and feel this gun offers is as good as it gets.
Realism:The Umarex HK P30 is a licensed replica of the real HK P30 semi auto pistol. It looks almost exactly like the real steel version with the exception of the break in the slide where the rotary magazine is accessible and the smaller .177 caliber muzzle opening.
Rifled barrel for Pellets but can also shoot BB's.
Full H&K Licensing.
German made!
Comes in a nice hard-shell case.
Full size drop out magazine that holds BB's and CO2.
Adjustable rear sight for windage.
Double and Single Action trigger.
Rail for adding accessories.
Very nice holding gun, good ball acne and weight.
Good accuracy and power.
Cons:
More expensive then many entry level guns but much higher quality.
Barrel is not recessed at all.
Did not get a lot of shots form a CO2.
Trigger is a bit tuff in double action mode.
Comments:
I have had a lot of people ask me to review this air pistol and to be honest I thought it would be just like the other Umarex German made rotary magazine pellet shooters, and that's not a bad thing! But it is different then the rest as it is the only one that also has the ability to shoot BB's by loading up the inline drop out magazine with 15 BB's and fitting the BB adapter where the rotary magazine would normally go. I also really like the look and feel of this gun. It is the perfect size and weight, not too big or small and not to heavy or light. I would really lie to get my hands on the real steel HK P30 to see if it has similar characteristics? If you want the best of both worlds, an accurate CO2 pellet pistol and an action shooting high capacity BB shooter, you can have it all with the HK P30.
Trigger Pull: The trigger pull for both KWC blowback single action pistols is very good, the Desert Eagle is a bit better with less play and a lighter pull while the Sigma SW40F still feels very good but has a little bit more take up and a slight bit more pull required.
Accuracy: I shot both guns from 20 feet out in semi rested position and got similar results. I was able to place 10 rounds in a 2.5 to 3 inch group and both guns shot well centered. I have full confidence that I could easily hit a man sized target from 50 feet away. Both KWC Airsoft pistols got right around 400 fps (5 shot average chrony testing) with the Desert Eagle only 10 fps higher than the Sigma SW40F and this was using .20 gram plastic Airsoft BB's.
Build Quality: The build quality for both guns is pretty much the same, both have a metal slide and barrel with a polymer frame and plastic grips, the Sigma SW40F had a plastic magazine release and trigger while the Desert Eagle used metal in these parts. The KWC Sigma SW40F seemed to wear a bit better as the painted finish seemed more durable. I found the metal on metal areas on the Desert Eagle where losing the paint and also in some of the high spots. Over all the guns worked very well and had good fit and finish.
Realism: The KWC Desert Eagle .50 and Sigma SW40F are very accurate replicas of their real steel counterparts, with the Desert Eagle also having the full licensing on it for added authenticity. The workings of both Airsoft guns are pretty much just like a real gun with full size drop out magazines and very heavy full blowback operation. The slides on each gun give a nice metallic sound when operating.
Very believable replicas of the real steel versions.
Cons:
Paint wear in high spots noticeable on the Desert Eagle.
Non adjustable sights.
Both go through CO2 fast.
No trademarks on the Sigma SW40F.
Comments:
It's wonderful to get these KWC blowback Airsoft guns here in Canada finally and have the ability to review them for everyone. They remind me a lot of the Cybergun 4.5mm Steel BB blowback pistols very much and this is probably because there are Airsoft version of these guns also distributed by KWC. Whether you want one of these very nice Airsoft pistols for plinking and target practice or to use in battle on the Airsoft field, either gun would make a great choice. I am really loving the fact that I now have more guns I can review and Airsoft or 4.5mm Steel BB it really doesn't matter to me, I'm having way to much fun to care ;)
