Type: Pellet Rifle. Distributer:Umarex. Model:Fusion 2. Materials: Metal and polymer build. Weight: 6.5pounds (2948 grams). Barrel: 22.5 inches, rifled. Total Length: 40.3 inches Propulsion: 12 gram CO2 x2 or 88 gram CO2 x1 Action: Bolt action repeater. Ammunition Type: .177 caliber pellets. Ammunition Capacity: 9 round rotary magazine x2. FPS: 490.
Trigger Pull: The trigger pull on Umarex Fusion 2 CO2 .177 Caliber Bolt Action Pellet Rifle feels pretty good, it is fairly short and light having a claimed 3.5 pound release which is believable. You will need to obviously work the bolt for each shot that precooks the internal hammer/striker allowing for the short and light trigger.
Accuracy: I have not performed my Field Test Shooting Video for the Umarex Fusion 2 CO2 .177 Caliber Bolt Action Pellet Rifle so stay posted for that. Umarex has claimed a velocity of around 490 FPS for the Canada version I will be testing, the US version has a claimed velocity of up to 700 for those in the US purchasing this Rifle. I am sure the included 4x32 optical scope once setup will help in the accuracy department when I test this CO2 Air Rifle out on a paper target setup 30 feet down range.
Build Quality: The Umarex Fusion 2 CO2 .177 Caliber Bolt Action Pellet Rifle is a fairly low cost target pellet Rifle when you consider it comes with a decent optical scope along with two 9 round magazines but even so the build quality seems very solid coming in at 6.5 pounds. The stock is plastic of course but there is lots of metal where you want it to be as in the bolt, trigger, safety and most other mechanical parts.
Realism: The Umarex Fusion 2 CO2 .177 Caliber Bolt Action Pellet Rifle is not a replace of any gun I know of but does sport a very modern ergonomic look with its pistol grip and molded full stock. I like the built in picatinny rail which even though it does not offer any type of open sight configuration will allow for a variety of scope mounting options for near or far shooting.
Pros:
Low cost for a full featured Air Rifle with included scope.
Nice ergonomic modern looking design.
Ability to use either 12 gram or 88 gram CO2 cartridges.
Comes with 4x32 optical scope and all mounting hardware needed.
Come with two 9 round rotary magazines.
May be very quiet if the SilencAir technology is not disabled here in Canada?
Single action 3.5 pound trigger fells good.
Safety is large and easy to use.
M-LOK slots for mounting additional hardware.
Cons:
No iron sight option if you would prefer that.
Limited to under 500 fps (Canada version).
Not sure about the functionality of the SilencAir technology in Canada?
Comments: I am looking forward to performing my Indoor Field Test Shooting Video for the Umarex Fusion 2 CO2 .177 Caliber Bolt Action Pellet Rifle to see if it performs as good as it looks. I’ll probably use the duel 12 gram configuration for this test since I don’t plan on shooting 300 rounds with it for my testing. We should also find out if the SilencAir technology has been disabled or not with my Canada version but even so, a 500 fps Air Refile is not going to be all that loud either way at the end of the day. There are not a lot of Bolt Action multi shot pellet Air Rifles out there especially in this price range so I am really hoping it hits a home run when I test it so stay posted for that video…
My Vimeo Videos for the Umarex Fusion 2 CO2 .177 Caliber Bolt Action Pellet Rifle:
In this Vimeo Replica Airguns Update Video I take a look at three CO2 Airguns, one is a 4.5mm Steel BB revolver distributed by Barra and two are CO2 Blowback Airsoft Pistols distributed by Umarex. All of these CO2 Airguns I have previously reviewed in slightly different versions either barrel length and finish or Steel BB as compared to 6mm Airsoft So checkout why other reviews on similar version Airguns.
The Barra Barra Schofield CO2 BB Revolver is a replica of the Schofield No. 3 single action revolver and utilizes 6 reloadable shells for a very realistic shooting experience. It is very solid in construction bing made mostly out of metal and weighs in at around 2.4 pounds. This version shots 4.5 mm Steel BBs at a velocity of up to 400 fps. It comes in a variety of barrel lengths and finishes so amen sure to have a look in our Online Replica Airguns Store for what we have available…
Next up from Umarex is the fully licensed Beretta Pietro Mod. 92 A1 CO2 Blowback Semi and Full Auto Airsoft Pistol, this product is distributed by Umarex but is made by KWC. Another solid metal pistol with a hefty 2.4 pound weigth that holds 21 rounds in its full size drop out metal magazine and offers both semi and full auto shooting at the flick of a switch!
Again from Umarex I showcase the Elite Force 1911 Tac CO2 Blowback Airsoft Pistol and like the Beretta Pietro it too is made in the KWC factory for Umarex. The 1911 Tac as the name suggest is a tactical version of the standard Colt 1911 but with some upgrades like a skeletonized hammer and trigger along with an ambidextrous safety, white dot sights front and back and a picatinny rail on the frame for add ons. You can expect velocity to be somewhere in the 400 fps range and the full size drop out metal magazine holds 15 Airsoft BB’s.
Type: BB Air pistol. Distributer: Crosman. Model:MAKO. Materials: Metal and polymer build. Weight: 1.71 pounds (775 grams). Barrel: 6 inches, non-rifled. Total Length: 8.6 inches Propulsion: CO2 x1. Action: Semi auto blowback, double action only. Ammunition Type: 4.5mm Steel BB's. Ammunition Capacity: 20 rounds. FPS: 425.
Trigger Pull: The trigger pull on the Crosman MAKO Blowback CO2 BB Pistol is a little on the heavy side since it is double action only and it is also longer again being double action only. That said it is fairly smooth and not super heavy which shoudl allow for decent action shooting. It would have been cane if the hammer could be engaged for single action shooting but the design of the Crosman MAKO Blowback CO2 BB Pistol does not allow for this and therefore the hammer is just for show in this case.
Accuracy: I have performed my Field Test Shooting Video for the Crosman MAKO Blowback CO2 BB Pistol which can be found here. I won’t get into too much detail but overall you can expect velocity to be in the 400 fps range with a brand new CO2 and accuracy was decent form 30 feet away but could be a bit tighter. I was surprised at how snappy the blowback action was for a light weight slide with a light spring in it.
Build Quality: The Crosman MAKO Blowback CO2 BB Pistol feels solid enough in the hand and the materials used I am sure are on par with most Airguns out there but the gun may come across as being on the cheaper side as it lacks some of the more full features of more realistic functioning blowback Airguns. Just don’t let that make you think it is not well made as it is well made and may even be more reliable over time..
Realism: The Crosman MAKO Blowback CO2 BB Pistol looks the part of a beretta M92 at first glance but when you get a little closer you can really tell it is an Airgun at heart which is not a bad thing since that’s exactly what it is. You will find working parts like the magazine release and slide catch release and the slide does function since it is a blowback Airguns but the Crosman MAKO Blowback CO2 BB Pistol does have that funny inner barrel that pops out of the front every time you pull the trigger and parts like the slide safety are moulded into the slide and the hammer is just for show.
Pros:
Fairly inexpensive.
High FPS rating for a blowback BB pistol.
Easy to see Fiber Optic front and rear sights.
Multi tone color scheme looks good.
Has a pleasing tactic look to it.
CO2 tab is nicely hidden inside grip under magazine but plate.
Double action trigger pull is long but not too firm.
Picatinny rail for adding accessories.
Notched grips for a firm hold (best for larger hands)
Has a working side catch release that locks back after the last shot.
Has a surprising decent blowback action to it.
Cons:
Slide action feels clanky.
Hammer is just for show, does not do anything, no single action shooting ability.
Grips are large and will be to bog for smaller hands.
Comments: All in all the Crosman MAKO Blowback CO2 BB Pistol is a fun inexpensive CO2 Blowback BB Pistol that surprised me a bit when I actual got to shoot it. I originally though ti would feel kind of cheap to shoot but the snappy and firm blowback action and higher fps than usually found on blowback Airguns was surprising! The fiber optic sights making lining up target super easy and for a double action only shooter the trigger is not too bad so if you're a Beretta and Crosman fan then perhaps this is the pistol for you.
My Vimeo Video for the Crosman MAKO Blowback CO2 BB Pistol:
Today I decided to get outside since the weather was nice and make my Field Test Shooting Video for the ASG TAC-6 CO2 Airsoft Rifle (actually outside in the filed!) After all the ASG TAC-6 CO2 Airsoft Rifle is a sniper rifle and so I wanted to test it out at longer ranges than my 30 foot indoor shooting range can allow for. So I setup two paper targets at around 40 feet and 80 feet out, the actually distance may have been longer than that?
Starting off my Field Test Review I placed five .25 gram plastic Airsoft BB’s through my Chronograph and averaged 446 fps which is 6 fps faster than the claimed 440 fps from ASG. And that was with .25 gram Airsoft BB’s so if I was using lighter .20 gram BB’s I would expect velocity closer to around 500fps so don’t be shooting anyone with this Airsoft Rifle at close ranges!
Next I proceeded with my accuracy test placing 5 rounds on the target setup around 40 feet downrange. I managed to get all 5 rounds within about 2 inches of each other, not bad since this is a good 10 feet more than I usually test my Airsoft Rifles at. With the remaining 10 rounds in my magazines I was hoping to get at least a couple shots on my paper target setup a good 80 feet away but did not have much luck, I even reloaded the 15 round stick magazine 2 more times and gave it a go but again with no success! The Airsoft BB’s seemed to want to angle off in all direction usually up and to the right or left right before the 80 foot target, perhaps I would have had much better luck at 60 feet?
All I can surmise from this higher range Field Test is that the ASG TAC-6 CO2 Airsoft Rifle is not really a long range Airsoft gun at least with the .25 gram Airsoft BB’s I was using, maybe heavier Airsoft BB’s would settle down a bit more? I can say at ranges up to 40 feet the ASG TAC-6 CO2 Airsoft Rifle did perform just fine so keep that in mind when looking into buying one of these as smoking cans at 30-40 feet will be no problem and make for some fun times in the back yard or even basement makeshift gun range.
Type: Airsoft Rifle. Manufacturer: ASG. Model:TAC-6. Materials: Plastic with some internal metal parts. Weight: 3.5 pounds (1588 grams). Barrel: 12 inches, metal non-rifled. Length: 36 inches. Propulsion: 12 gram CO2 x 1. Action: Semi auto, double action only. Ammunition Type: 6mm BB's. Ammunition Capacity: 15 round metal stick magazine. FPS: 440.
Trigger Pull: The double action only type trigger pull on the ASG TAC-6 CO2 Airsoft Rifle is not too heavy but it is rather long so really quick rapped fire shooting will require some finger work. The trigger reset is right at the begging of the pull so you need to make sure you allow the trigger full range of motion or you may miss the odd shot.
Accuracy: I haven't done my Field Test Shooting video just yet for the ASG TAC-6 CO2 Airsoft Rifle but will shortly so stay posted for that video. ASG claimed the fps to be right around 440 and I am assuming with .20 gram Airsoft BB’s, I will most likely busing .25 gram Airsfto BB’s for my testing so I am hoping for around 400 fps or so. With the fiber optic front sight and fully adjustable rear peep sight I shoudl be able to get some decent rounds on target downrange and hopefully get a nice grouping.
Build Quality: The ASG TAC-6 CO2 Airsoft Rifle is mostly plastic but feels pretty good in the hand with decent fit and finish. There are some metal internal part along with the outer barrel and top rail but for the most part the ASG TAC-6 CO2 Airsoft Rifle is all plastic including the trigger and front and rear sights.
Realism: The ASG TAC-6 CO2 Airsoft Rifle is not a replica of any modern rifle that I know of but it does look a bit like a Beretta CX4 Storm especially the back half of it. The flash hider and top and bottom raise add to the realism. Available From: The Replica Airguns Store.
Pros:
Very customizable with rails top and bottom.
Comes with a rather nice Bipod that can be used with other rifles.
Front and back removable Iron sights are very usable, fiber optic in front, peep in back.
Safety switch is in a great location for right handed shooters.
Canada version comes with black flash hider.
Mostly plastic but solid construction.
Rubber Butt Pad is nice and thick.
Removable barrel to reduce size for easier transportation.
Also come in 4.5mm Steel BB version.
Optional Integrated laser can be added.
Cons:
DOA Trigger pull is a bit long which will slow down rapid fire shooting a bit.
Mostly Plastic Polymer build.
Why not a longer inner barrel for possible more fps?
CO2 is in the Pistol grip and not the magazine so may not be great for on field battles.
Comments: This may not be the most exciting Airsoft Rifle I have reviewed, it does look kind of cool and the price is right compared to other Airsoft Rifles. Who is it really for? I would say someone looking for an Air Rifle for plinking in the backyard or basement that perhaps want's a little bit more safety in terms of using plastic BB’s rather than Steel BB’s. Sure you can use the ASG TAC-6 CO2 Airsoft Rifle for Airsoft wars but most people want something a bit more realistic in terms of looks and function. Because the ASG TAC-6 CO2 Airsoft Rifle does have built-in Popup it shoudl be able to reach out to longer ranges so we will have to see if it can perform decent at longer ranges when I do my Field test Shooting Video.
My YouTube Table Top Review Video for the ASG TAC-6 CO2 Airsoft Rifle:
This Table Top Comparison video is also a bit of a revisit since I reviewed the US version of the Sig Sauer ASP MPX .177 Cal. Pellet Rifle back in 2016 when it first came out. I actually had to go across the border and bring it back across with me which can be a lot of fun dealing with Canada Customs border agents. They are well meaning but often don’t fully understand their own import guidelines for Airguns. After about an hour or so I was able to convict the CBSA officer that no my Sig Sauer Airguns where not regulated Firearms and no they did not require any registration or transfer permits.
Anyway that was 5 years ago and now we have the Canada import version which makes purchasing one of the Sig Sauer ASP MPX .177 Cal. Pellet Rifles so much easier and to be honest there really isn’t any difference as far as I can tell since my original US version even though it had a claimed fps of up to 600 was actually closer to somewhere in the mid 400’s using standard .177 caliber lead pellets.
Below are the basic specifications and if you want more info than that either watch the video or checkout my Original Table Top Review for the Sig Sauer ASP MPX .177 Cal. Pellet Rifle since both the original US and newer Canada versions are virtually identical…
Type: Pellet Rifle. Manufacturer: Sig Sauer ASP Model: Sig Sauer MPX ASP Materials: Metal and Nylon Fiber build. Weight: 7 Pounds (3300 Grams). Barrel: 8 inch steelrifled. Propulsion: 88 or 90 Gram CO2. Action: Semi Auto,double action only. Ammunition Type: .177 caliber pellets. Ammunition Capacity: 30 rounds belt fed. FPS: Up to 575-600 fps (When shot by a Unicorn) Probably closer to around 450fps
I will be following this Tabel Top Review for the US and Canada Sig Sauer ASP MPX .177 Cal. Pellet Rifles with a Field Test Shooting Comparison to see if anything has really changed interns of velocity and accuracy so stay posted for that video coming out very soon…
In this Field Test Shooting Video I perform my usual Chronograph and Accuracy tests in the Replica Airguns Indoor Sea Can Shooting Range to find out what the actual feet per second velocity is and how accurate the ICS CPX-APE SF1 AEG Airsoft Rifle is in both semi auto and full auto. Watch my Table Top Video if you are looking for more info on Specifications and Details along with a full tear down of the ICS CPX-APE SF1 AEG Airsoft Rifle.
First up I place 6 rounds through my Chronograph to see what the real world velocity is and the ICS CPX-APE SF1 AEG Airsoft Rifle was able to average 391 fps using .25 gram plastic Airsoft BB’s. ICS claims the ICS CPX-APE SF1 is capable of fps up to 460 fps but this would be using lighter .20 gram Airsoft BB’s which I believe is entirely possible!
Next I put a fresh paper target on my metal backstop 30 feet downrange and proceeded to shoot 10 round in semi auto to see how tight of a grouping I could get. I was happy to see that 7 of my 10 rounds all grouped nicely within the 1.5 inch bullseye and only 3 came out just slightly increasing the grouping to around 2 inches but still closer to 1.5 inches. When I switched over to full auto and emptied the 300 round magazine into the target, amazingly the grouping still seemed to stay pretty close to 2 inches in diameter with some stragglers. The ICS CPX-APE SF1 AEG Airsoft Rifle punched a satisfying hole in my target going through several layers of cardboard.
As you can see in this YouTube Field Test Shooting Video the ICS CPX-APE SF1 AEG Airsoft Rifle performed very well for me living up to its pristine price point. You will pay top dollar for the ICS CPX-APE SF1 AEG Airsoft Rifle but will also get top quality with a ton fo features including an almost all metal/aluminum build, ambidextrous controls throughout, tons of add on capabilities using the 5 sided Keymod hand-gurd, fully adjustable folding stock and exceptional performance.
Type: AEG EBB Airsoft. Manufacturer: ICS Model: CPX-APE SF1 Materials: Mostly Metal/Aluminum. Weight: 6.4 pounds (2900 grams). Length: 25.2 inches folded / 32.5-36.2 unfolded. Hop-up: Yes adjustable. Propulsion: AEG EBB (Electric Blowback). Action: Semi & Full Auto single action only electric trigger. Ammunition Type: 6mm plastic Airsoft BB's. Ammunition Capacity: 300 rounds. FPS: 460 fps.
Trigger Pull: The trigger pull on the ICS CPX-APE SF1 AEG Airsoft Rifle is pretty much like most AEG Electric trigger operated Airsoft Rifles. Usually mid range, light and with no real noticeable release point since it is an electric on and on switch at the end of the day and not really mechanical. Of course you can elect between semi and full auto operation at will.
Accuracy: I have not done my actual Field Test Shooting video review for the ICS CPX-APE SF1 AEG Airsoft Rifle but plan to tackle this video next on my list so this week for sure, stay posted of this one as I have not Field Tested any ICS Airsoft Rifles to date and really don’t know what to expect!
Build Quality: The G&G ICS CPX-APE SF1 AEG Airsoft Rifle is extremely well made as the price tag would suggest. You are going to find metal almost everywhere on this product including the all aluminum upper receiver. The only plastic I could find on the ICS CPX-APE SF1 AEG Airsoft Rifle was in the magazine and the folding butt stock. Everything else is metal/aluminum including the upper and lowe receivers, the sights, the rails and all of the controls. Fit and finish feels great as-well!
Realism: The ICS CPX-APE SF1 AEG Airsoft Rifle is not a replica so to speak of any one particular gun in production but does have some AR and perhaps SCAR attributes to it. Perhaps there needs to be a real steel version of this gun as it does combine a bit of the best of a both platforms. The ICS CPX-APE SF1 AEG Airsoft Rifle is sold for sure with great weigth and feel to it being that it is mostly metal. All the controls work exactly like you would expect on a the real powder burner and you can totally take this Airsoft rifle apart in just a minute or two with virtually no tools.
Mostly metal construction with full aluminum upper receiver.
Tons of rail attachment options with the 5 sided Keymod rail hand-guard.
Fully adjustable pop-up iron sights.
Most everything is ambidextrous: Selector switch, Magazine release, Charging handle, Sling mount.
Rear folding stock has tons of positions, 6 in length and 5 for cheek rest.
Super easy access to everything, hop-up, gear box, inner barrel, outer barrel.
Electric blowback system for slight recoil effect.
T-window in magazine for quick ammunition checks.
FPS is nice and high, great for longer range shooting.
Cons:
On the expensive side but very high quality.
Limited battery options as space for a battery is tight.
May have a bit too high of fps for closer quarter indoor Airsoft games.
Comments:
The ICS CPX-APE SF1 AEG Airsoft Rifle is not an inexpensive product and may be a bit out of touch for Airsofters on a tighter budget. That said it is really well thought out and well built Airsoft product that is ready to go with no real upgrading required. You may want to show on an optical or red dot sigh, perhaps a tac light or fore grip? Nothing you need right away. There really isn’t one thing I can point out that makes this gun so great, it is a combination of everything. when it comes down to it the ICS CPX-APE SF1 AEG Airsoft Rifle kind of has it all going for it. I am looking forward to seeing just how well it performs during my Indoor Field Test. I have high hopes!
I am super excite to showcase three awesome rifles in this Update Preview Unboxing Video. Two of which are Airsoft and one is a Steel BB shooter, all of which are semi and full auto selectable. In this video I do a bit of an unboxing and preview of each Rifle not going into too much detail as I want to leave most of the information for my Table Top and Filed Test Videos. The main purpose of this video is to let everyone know we have these Rifles in our Canada Replica Airguns Store now for sale.
I may as well talk about them in the order they appear in my video so lets start with the ICS CXP APE AEG Airsoft Rifle. The ICS CXP APE AEG Airsoft Rifle is a mostly metal Electric Airsoft Rifle with realistic electronic blowback operation along with a CNC machined aluminum upper and lower receiver. It comes with a hi-cap 300 round magazine and a Ver 2 Full Metal ICS Split Type Gearbox. The ICS CXP APE AEG Airsoft Rifle weighs in at just under 3kg.
Next I showcase the G&G SMC9 GBB Airsoft Carbine, a unique product that converts the G&G GTP9 pistol into a a semi and full auto Carbine and includes a 50 round extended magazine, there is an even higher capacity drum magazine made for this product! You will find a fold out stock along with a CNC Machined MLOK Rail for additional mounting options.
Last but perhaps one that I have been the most eagerly anticipating is the Crosman AK1 CO2 Blowback BB Rifle a twin CO2 Blowback 4.5mm Semi and Full auto AK style BB Rifle, finally a decent AK BB Rifle! The Crosman AK1 CO2 Blowback BB Rifle has a claimed fps of 430 and shoots 1400 rounds per minute in full auto, very similar to the Crosman DPMS series of AR styled CO2 Blowback Full Auto BB Rifles. The Crosman AK1 CO2 Blowback BB Rifle comes with a 25 round magazine and swing out rear adjustable stock.
In this Field Test Shooting Video I test out the Velocity and Accuracy of the Umarex VFC Heckler & Koch HK416 V2 AEG Airsoft Rifle by first placing 5 rounds through my Chronograph and recording the feet per second for each shot and then averaging them out. For the second portion of my Indoor Shooting Performance Test I setup a paper target 30 feet down range followed by shoot 10 rounds back to back to see what the spread or grouping size is. I followed this up with a nice long full auto burst just for fun to see if the grouping still remains nice and tight.
For my Velocity test I used .25 grain Plastic Airsoft BB’s rather than the normally tested .20 in the claimed fps of over 366 fps so I was expecting to get a little bit lower velocity results. I did manage to average right around 304 fps with all shots fairly consistently with the slowest being 302 fps and the fastest hitting 305 fps.
I then setup my brand new paper target and using a rested and seated shooting position from 30 feet back I placed my first 10 rounds into the target. The Umarex VFC Heckler & Koch HK416 V2 AEG Airsoft Rifle did shoot a little bit low close to the bottom of the rings but not as low as when I tested the Heckler & Koch HK416C version, I am sure some hop-up adjustment will get this closer to the mark. I did mange to get a really tight 10 round grouping of close to half an inch with most of the BB’s hitting one o top of the other I would ahed to say this is the best 30 foot accuracy results I have gotten from any Airsoft rifle to date! Full auto was as predicted, lots of fun with a nice hole in the paper/cardboard leaving about a 2 inch opening.
The Umarex VFC Heckler & Koch HK416 V2 AEG Airsoft Rifle performed really well for me and as already mentioned is crazy accurate. It had a slightly lower fps than the Heckler & Koch HK416C version which was a bit of a surprise but at 304 fps using .25 gram Airsoft BB’s this is about perfect for close quarters shooting adn even out to medium distances. Make sure not checkout all of our Umarex VFC Heckler & Koch over in the Replica Airguns Canada Online Store.
In this Field Test Shooting Video I test out the Velocity and Accuracy of the Umarex VFC Heckler & Koch HK416C V2 AEG Airsoft Rifle by first placing 5 rounds through my Chronograph and recording the feet per second of each shot then averaging them out. For the second portion of my Indoor Shooting Performance Test I setup a paper target 30 feet away and then shoot 10 rounds back to back to see what the spread or grouping size is. I follow this up with a full auto burst just for fun to see if the grouping still remains nice and tight.
For my Velocity test I used .25 grain Plastic Airsoft BB’s rather than the .20 in the claimed fps over 366 fps so I was expecting to get a little bit slower results. I did manage to average right around 325.5 fps with all shots consistently hitting either 325 or 326 fps so super consistent.
I then setup my brand new paper target and using a rested and seated shooting position from 30 feet back I placed my first 10 rounds into the target. This is when I discovered the Umarex VFC Heckler & Koch HK416C V2 AEG Airsoft Rifle liked to shoot fairly low even when using the raised elevation option on the rear sight. Because of this I had to aim a little bit higher on the paper target to place shoots more centered. Once I figure out my aim point I did mange to get a fairly tight 10 round grouping of close to an inch with a couple of stagers pushing it out to 2 inches. Full auto was as predicted, lots of fun with a nice hole in the paper/cardboard leaving about a 3.5 inch opening.
The Umarex VFC Heckler & Koch HK416C V2 AEG Airsoft Rifle performed well for me once I figured out that it liked to shoot rather low. I would suggest placing a bit of a spacer or riser under the rear sight to bring up the barrel at least for closer in shots where hop-up may not ark the Airsoft BB enough at that point. Other than that the Umarex VFC Heckler & Koch HK416C V2 AEG Airsoft Rifle had super consistent performance in terms of both FPS and accuracy.
Type: AEG Airsoft Rifles Manufacturer:Umarex / VFC Model:HK416 V2 Materials: Fiberglass reenforced plastic and metal. Weight: 7 pounds (3180 grams). Total Length: 28 - 31.1 inches (710-790). Barrel: 10.2 inches (260mm) non rifled. Propulsion: AEG. Action: Single action semi & full auto. Ammunition Type: .6mm plastic Airsoft BB’s. Ammunition Capacity: High cap 320 round magazines. FPS: 366+ fps.
Trigger Pull: The trigger pull on the Umarex VFC Heckler & Koch HK416 V2 AEG Airsoft Rifle is similar to a light single action trigger as they are essentially an electrical on off switch. There is about a quarter inch of take up with virtually no extra friction to let you know when the release is going to be, with a bit of use you will figure out exactly when the trigger will release the action.
Accuracy: At this time I have not made my Field Test Shooting Video or even shot the Umarex VFC Heckler & Koch HK416 V2 AEG Airsoft Rifle, but plan to make my Field Test Shooting Video shortly. So stay posted for that video coming out soon. I do expected Umarex VFC Heckler & Koch HK416 V2 AEG Airsoft Rifle to perform well as it is a high quality and not so inexpensive AEG Airsoft Rifle.
Build Quality: The Build quality on the Umarex VFC Heckler & Koch HK416 V2 AEG Airsoft Rifle looks to be really good, there are lots of quality metal parts throughout this Airsoft Rifle including the top and bottom receiver, rails, parts of the sights, flash hider, magazine, charging handle, selector switch, magazine release, forward assist, dust cover, buffet tube and trigger. VFC (Vega Force Company) is the actual manufacturer of this product line and they are well know for making high quality Airsoft products.
Realism: The Umarex VFC Heckler & Koch HK416 V2 AEG Airsoft Rifle is a 1 to 1 scale fully licensed replica of the real steel HK 416 compact CQB styled rifles . You’ll find that most part work in the same manner as with the real steel version including the Charging Handle, Forward Assist, Bolt Release, Magazine Release, Selector Switch and Pop-up sights.
Pros:
Full H&K Licensed via Umarex.
Made by VFC (Vega Force Company), well known for quality products.
Lots of metal parts where would find them on the real steel HK416.
Semi auto & full auto selectable.
No orange tip on Canada import version.
Comes with AR type compatible high capacity 320 round magazine.
Removable metal sights are adjustable for windage.
Lots of rail attachment positions.
Easy access to hop-up system.
Quality internals - V2 metal gearbox and built in Mosfet.
Fully adjustable rear stock.
Cons:
Price is on the higher end.
No elevation adjustment on sights.
Comments:
The Umarex VFC H&K AEG Airsoft product line is going to be on the higher end of the price spectrum for sure but you are getting a really quality product here fully H&K licensed. The Umarex VFC Heckler & Koch HK416 V2 AEG Airsoft Rifle has a really nice form factor allowing for a full size rear adjustable stock which will make your shooting position a lot more comfortable while still allowing for a rather compact form factor overall. I look forward to seeing how well the Umarex VFC Heckler & Koch HK416C V2 AEG Airsoft Rifle performs in my upcoming Field Test Shooting Video.
My Vimeo Table Top Review for the Umarex VFC HK416 V2 AEG Airsoft Rifle:
Type: AEG Airsoft Rifles Manufacturer:Umarex / VFC Model:HK416C V2 Materials: Fiberglass reenforced plastic and metal. Weight: 6.1 pounds (2780 grams). Total Length: 22.6 - 27.4 inches (573-696mm). Barrel: 8.3 inches (210mm) non rifled. Propulsion: AEG. Action: Single action semi & full auto. Ammunition Type: .6mm plastic Airsoft BB’s. Ammunition Capacity: High cap 320 round magazines. FPS: 366+ fps.
Trigger Pull: The trigger pull on the Umarex VFC Heckler & Koch HK416C V2 AEG Airsoft Rifle is similar to a light single action trigger as they are essentially an electrical on off switch. There is about a quarter inch of take up with virtually no extra friction to let you know when the release is going to be, with a bit of use you will figure out exactly when the trigger will release the action.
Accuracy: At this time I have not made my Field Test Shooting Video or even shot the Umarex VFC Heckler & Koch HK416C V2 AEG Airsoft Rifle, but plan to make my Field Test Shooting Video shortly. So stay posted for that video coming out soon. I do expected Umarex VFC Heckler & Koch HK416C V2 AEG Airsoft Rifle to perform well as it is a high quality and not so inexpensive AEG Airsoft Rifle.
Build Quality: The Build quality on the Umarex VFC Heckler & Koch HK416C V2 AEG Airsoft Rifle looks to be really good, there are lots of quality metal parts throughout this Airsoft Rifle including the top and bottom receiver, rails, sights, flash hider, magazine, charging handle, selector switch, magazine release, forward assist, dust cover and trigger. VFC (Vega Force Company) is the actual manufacturer of this product line and they are well know for making high quality Airsoft products.
Realism: The Umarex VFC Heckler & Koch HK416C V2 AEG Airsoft Rifle is a 1 to 1 scale fully licensed replica of the real steel HK 416 compact CQB styled rifles but in an even more compact design I believe specifically only found in Airsoft versions as I was not able to find the exact same model on the H&K Website. That said most part work in the same manner as you would find on the real steel version including the Charging Handle, Forward Assist, Bolt Release, Magazine Release, Selector Switch and Pop-up sights.
Pros:
Full H&K Licensed via Umarex.
Made by VFC (Vega Force Company), well known for quality products.
Lots of metal parts where would find them on the real steel HK416.
Semi auto & full auto selectable.
No orange tip on Canada import version.
Comes with AR type compatible high capacity 320 round magazine.
Pop up metal sights are adjustable for windage.
Lots of rail attachment positions.
Easy access to hop-up system.
Quality internals - V2 metal gearbox and built in Mosfet.
Ultra compact adjustable CQB stock.
Cons:
Price is on the higher end.
No elevation adjustment on sights.
Limited to physical size/type of battery used.
Comments:
The Umarex VFC H&K AEG Airsoft product line is going to be on the higher end of the price spectrum for sure but you are getting a really quality product here fully H&K licensed. The Umarex VFC Heckler & Koch HK416C V2 AEG Airsoft Rifle is perhaps one of my favorites as I like more simplistic and minimalist styles of guns and this one for sure fits into that category. Even though it is small in nature it is super solid and heavier then it looks for sure when you pick it up with all the metal parts making up its build quality. I look forward to seeing how well the Umarex VFC Heckler & Koch HK416C V2 AEG Airsoft Rifle performs in my upcoming Field Test Shooting Video.
My Vimeo Table Top Review for the Umarex VFC HK416C V2 AEG Airsoft Rifle:
In this video I show you four Premium AEG Airsoft Rifles made by VFC and distributed and H&K Licensed by Umarex. This is not a detailed review but rather I focus on the basic specification and show my reaction as I take my first look at all four Umarex H&K AEG Airsoft Rifles. I do show off some close up photos so you can get an idea on the finish and what some of the components look like.
For this Field Test Shooting Video I put the Specna Arms RRA SA-C10 Core and Specna Arms RRA SA-E10 Edge head to head to see just how they will compare in terms of FPS and Accuracy at least out to 30 feet. If you want to know more about each of these AEG Specna Arms Airsoft Rifles then checkout my Table Top Review where I show them up nice and close and also talk about their specifications and how they both compare to each other.
For my Chronograph test, I decided to go with .25 gram Airsoft BB’s, a little bit heavier than what was used for the claimed FPS of around 380 using the M120 spring which by the way is preinstalled in these guns for import into Canada. Both the Specna Arms RRA SA-C10 Core and E10 Edge shot pretty similar with the C10 Core averaging right around 300 FPS and the E10 Edge shooting a little bit faster with 318 FPS. Throw some lighter .20 gram Airsoft BB’s into the mix and these numbers would go up for sure. I was using the same 11.1 volt Li-Po battery for all of my testing in this video.
Next I placed a fresh paper target 30 feet downrange and placed 10 semi auto rounds into it using a seated and rested shooting position. Both Specna Arms AEG Airsoft Rifles shot about a 1 inch grouping. I did find with both of these Specna Arms rifles that when using the peep sight they shot too low and when using the top notch sight they shot too high at least at this distance. Of course the sights are fully adjustable so this can easily be taken care of and you can adjust the hop-up for even more elevation considerations. After my 10 shot semi auto test I placed both Specna Arms Airsoft rifles in Full Auto and let the paper have it! As expected the groupings did spread out a little bit but not all that much, perhaps opening up to around 3-4 inches.
After testing both the Specna Arms RRA SA-C10 Core and E10 Edge AEG Airsoft Rifles side by side you really can’t go wrong with either version as they performed very similarly on the Chronograph and on Target. If you can afford to pay the little bit more than I would go with an Edge Series Specna Arms product since you do get a lot of extras for the little bit more you pay. Well worth it!
Type: AEG Airsoft Rifles Manufacturer:Specna Arms. Model: RRA SA-C10 / RRA SA-E10 Materials: Fiberglass reenforced plastic and metal/aluminum. Weight: C10 4.9 pounds ( 2.2 kg) - E10 5.1 pounds (2.3 kg). Total Length: 21.7 - 25.2 inches (550 - 640mm). Barrel: 6.7 inch (170mm) inner 6.03mm tight bore barrel non rifled. Propulsion: AEG. Action: Single action semi & full auto. Ammunition Type: .6mm plastic Airsoft BB’s. Ammunition Capacity: Mid cap 120 round magazines. FPS: 375 - 390 fps with installed spring, included M90 spring will be lower fps.
Trigger Pull: The trigger pull on both of the Specna Arms RRA SA-C10 Core and E10 Edge AEG Airsoft Rifles is similar to a light single action trigger as they are essentially an electrical on off switch. There is a little bit of take up with virtually no extra friction to let you know when the release is going to be, with a bit of use you will figure out exactly when the trigger will release the action.
Accuracy: At this time I have not made my Field Test Shooting Video or even shot the Specna Arms RRA SA-C10 Core and E10 Edge AEG Airsoft Rifles, but plan to very soon. They are next on my list for Filed Test Shooting Videos so stay posted for that video coming out soon. I do expect them to perform well and will be shooting both of these models side by side to see if there is any noticeable difference between the lower cost Core versus the slightly more premium Edge Specna Arms versions.
Build Quality: One thing I can say is no matter which version of the Specna Arms AEG Air Rifles you deicide to go with (either a Core or Edge Series), you are getting extremely good value for your money and neither one is going to have any low quality parts in it. Even the lower cost Core Series will have fiber glass reenforced plastic and metal parts along with a metal gearbox and virtually almost the same build as the more premium and slightly higher priced Edge Series. You will get upgrades in the Edge Series such as a an aluminum receiver and buffer tube, a GATE X-ASR Mosfet, the New Orion Gearbox, deep laser engraved licensing and an additional magazine. All of this for the little bit more you pay for an Edge series Specna Arms AEG Airsoft rifle.
Realism: The Specna Arms RRA SA-C10 Core and E10 Edge AEG Airsoft Rifles are based on the AR15 or M16 platform of course in a very modern and PDW styled look. They look and feel the part for sure with lots of working parts including the safety, selector switch, charging handle, dust cover, adjustable rear stock, pop-up front and rear sights as you would expect. Most of the hardware should be interchangeable with a real steel AR if you want to personalize the look of your Specna Arms Rifle.
Pros:
Super affordable yet very high quality product for what you pay.
Two options to consider, both with good price points and value.
Quality components throughout both the Core and Edge series.
Rock River Arms Licensed with hologram on receiver.
ESAâ„¢ quick spring change system makes spring changes quick and easy.
Comes with two springs for potential indoor and outdoor usage.
Plastic parts are fiberglass reenforced making them very durable.
Quick release fully adjustable pop-up sights.
No orange tips on our Canada Store versions.
Lots of rial mounting options even on such short PDW styled AR’s.
Metal gearboxes with metal gears and mostly all metal parts inside.
Easy access to motor for any possible trouble shooting you may need to do.
Cons:
Popup sights are mostly plastic..
Need to hold back charging handle to access the hop-up wheel.
Comments:
Value for your money is what comes to mind when I think about the entire Specna Ams AEG Airsoft Riffle product line. And this goes for not only the lower priced Core Series but also the premium Edge Series. Both version are built supper tuff with quality components throughout. You are just getting upgrades you are probably going to do at some point in time with the Edge Series and of course more metal components when you spend about $100 more for a similar Edge version. I figure if you can muster up the extra cash then go with an Edge Specna Arms AEG Airsoft Rifle, that said, any of the Core models will be money well spent.
Make sure not also watch my previous Specna Arms YouTube Video where I introduce the product line, show you around several models and talk about the key differences between the Core and Edge versions.
My Vimeo Table Top Review for the Specna Arms RRA C10 Core & E10 Edge Airsoft Rifles:
We have a new line of Airsoft rifles from Specna Arms I am super happy to be introducing to the Replica Airguns Airsoft Community.
Specna Arms AEG Airsoft Rifles are extremely cost effective and offer value for what you pay that is amazing. In this YouTube Introduction Video I go over the main differences between the Core Series (lower priced) versus the Edge Series (mid priced) so that you can understand what the extra cost will get you when buying a Spenca Arms Edge Series AEG Airsoft Rifle over a Specna Arm Core Series AEG Airsoft Rifle.
I also show 12 different versions from the Specna Arms Core and Edge Series some with Rock River Arms licensing and some without.
Specna Arms Core Series
Price: Mid $200’s (CAD)
Materials: Fiberglass Reenforced Plastic & Metal
Mosfet System: No
Gear Box: Ver 2 Metal Fully Upgradeable
Spring System: ESA Quick Change - 2 Springs (380-310 fps)
Make sure to watch my Table Top Review for the Diana Bandit PCP .177 Caliber Bolt Action Pellet Pistol if you haven’t already done so to get all the specifications and features along with some nice close up video. In this Field Test Shooting video I test out the Diana Bandit PCP .177 Caliber Bolt Action Pellet Pistol to find out what the real world velocity is and also just how accurate it will be shooting a paper target from 30 feet back using a rested shooting position. Since the Diana Bandit PCP .177 Caliber Bolt Action Pellet Pistol is a target pistol I was hoping for good accuracy since the Diana Chaser performed so well for me in my earlier Field Test Shooting video this week. The Diana Bandit does have a claimed 700 fps velocity but I believe this is for the non-Canada detuned version so it will be interesting to find out exactly what the power is.
First up I placed 5 shots through my Chronograph with a fully charged PCP tank using 6.9 grain RWS lead pellets and got just over 500 fps results averaging 517 fps, so yes the Diana Bandit PCP .177 Caliber Bolt Action Pellet Pistol has been detuned to make it Canada non-regulated legal.
Next I performed my accuracy test shooting at a paper target 30 feet down range with the Diana Bandit PCP .177 Caliber Bolt Action Pellet Pistol rested on a sand bag up front and sitting in the back. Since the magazine holds 9 rounds I placed 9 round on the target to see what kind of grouping I could get. At first I was not sure why my 9 shot grouping seemed to be much more spread out than My Dianna Chaser results but after watching the video I saw that only one shot really came out of the 1 inch grouping not including the random accident shot I took. Perhaps I had a misinformed pellet or perhaps I pulled that one shot. That shot aside both the Diana Bandit and Chaser performed about the same, even shooting just a hair to the left from the bullseye.
The trigger feels pretty decent, not super light or to heavy, there is a little bit of take-up and then a slight resistance then a quick release. The bolt action along with the 9 round rotary magazine worked flawlessly for me with no jamming at all. For the low price this PCP Target Pellet Pistol comes in at you really can’t go wrong and if you want to modify or upgrade it down the road there are tons of things you can do to the Diana Bandit PCP .177 Caliber Bolt Action Pellet Pistol. I highly recommend the Diana Bandit PCP .177 Caliber Bolt Action Pellet Pistol if you are looking for a super affordable PCP target pellet pistol.
Make sure to watch my Table Top Review for the Diana Chaser CO2 .177 Caliber Bolt Action Pellet Pistol if you haven’t already to get all the specifications and features along with some nice close up video. In this Field Test Shooting video I test out the Diana Chaser CO2 .177 Caliber Bolt Action Pellet Pistol to find out what the real world velocity is and also just how accurate it will be shooting a paper target from 30 feet back using a rested shooting position. Since the Diana Chaser CO2 .177 Caliber Bolt Action Pellet Pistol is a target pistol I was hoping for good accuracy but based on the claimed 525 fps velocity I was also hoping for close to 500 fps results.
First up I placed 4 shots through my Chronograph using a brand new CO2 along with 6.9 grain RWS lead pellets and got pretty close to 500 fps results averaging 490 fps, not bad considering the temperature was not super warm and I was using led pellets not hyper velocity alloy pellets.
Next I performed my accuracy test shooting at a paper target 30 feet down range with the Diana Chaser CO2 .177 Caliber Bolt Action Pellet Pistol rested on a sand bag up front and sitting in the back. Since the magazine holds 9 rounds I placed 9 round on the target to see what kind of grouping I could get. I was impressed to see a nice 1 inch grouping, maybe even a little bit less removing the paper tearing. Shots where vertically right on the mark and just a tad to the left but easily fixable with a quick tweak of the full adjustable sights.
The trigger feels pretty decent, not super light or to heavy , there is a little bit of take up and then a slight resistance then a quick release. The bolt action along with the 9 round rotary magazine worked flawlessly for me with no jamming at all. For the low price this CO2 Target Pellet Pistol comes in at you really can’t go wrong and if you want to modify or upgrade it down the road there are tons of things you can do to the Diana Chaser CO2 .177 Caliber Bolt Action Pellet Pistol. I highly recommend the Diana Chaser CO2 .177 Caliber Bolt Action Pellet Pistol if you are looking for a super affordable target pellet pistol.
Type: Pellet Pistol Manufacturer:Diana. Model:Bandit Materials: Wood and Metal, some plastic. Weight: 2.2 pounds (1000 grams). Total Length: 20.1 inches (51 cm) Barrel: 9.5 inches (24 cm), metal rifled. Propulsion: PCP. Action: Bolt. Ammunition Type: .177 & .22 Caliber pellets. Ammunition Capacity: Single shot to 9 & 7 round magazines.. FPS: 725 (.177) - 630 (.22). Need to test for Canada import version
Trigger Pull: The trigger pull on Diana Bandit PCP .177 Caliber Bolt Action Pellet Pistol is single action only meaning in order to cock the internal hammer/striker, you need to cycle the bolt back and forth allowing for a short and light trigger action. It does come with a rotary multi-round magazine that allows for the cycling of the bolt to automatically advance a pellet allowing for much quicker followup shots.
Accuracy: At this point I have not personally tested the Diana Bandit PCP .177 Caliber Bolt Action Pellet Pistol in terms of actual power and accuracy but I expect the Diana Bandit PCP .177 Caliber Bolt Action Pellet Pistol to perform well since in fact this is a target pistol with fairly high claimed fps. In the next few weeks I plan on making my Field Test Shooting Video so stay posted for the results from that video for confirmation of the performance.
Build Quality: The Diana Bandit PCP .177 Caliber Bolt Action Pellet Pistol is made in China which might make you wonder about the overall quality of this target pistol but after taking a good look around and working all the mechanical parts I ma very impressed with the overall quality and chosen material that went into the production of the Diana Bandit PCP .177 Caliber Bolt Action Pellet Pistol. You will finds metal where you need it as in the barrel, bolt and trigger. The pistol grip are made of wood but you will find some portions of the sights are plastic but it would have been nice if they where all metal.
Realism: Realism isn’t really a concern with the Diana Bandit PCP .177 Caliber Bolt Action Pellet Pistol since it is not a Replica Airguns but in terms of looking like a gun it serves that purpose, no mistaken that so no waving it around in public or things may not turn out so good for you…
Pros:
Inexpensive fairly high quality full featured target pistol for the price.
Expect good accuracy!
Metal construction where it needs to be (Bolt, barrel, trigger).
Rifled barrel.
Fully adjustable sights.
Adjustable and light single action trigger.
Dove tail on bolt for adding optical sight.
Nice wood pistol grip.
Good for small pest control because of fairly high fps and expected good accuracy for shot placement ability.
Overall the gun feels really high quality for the price.
Even comes with a nice soft shell case.
Available in both .22 and .177 caliber pellet versions.
Cons:
Grips may be a bit too wide for smaller handed shooters.
Allen key does not fight the trigger adjustment.
Made in China.
Will need a pump or way to pressurize.
Comments:
For the price I don’t think you will find anything out there in terms of a PCP target pellet pistols with as many features as the Diana Bandit PCP .177 Caliber Bolt Action Pellet Pistol. At least in the lower cost price point Diana is offering it at. For that reason it is not going to be the absolute best all around PCP pellet firing target pistol you can get but I am sure bang for your buck you will be happy with this one. Everything about the Diana Bandit PCP .177 Caliber Bolt Action Pellet Pistol feels good quality, I would expect to pay at least double the price for something similar for sure. I have a feeling keeping the Diana Bandit PCP .177 Caliber Bolt Action Pellet Pistol in stock is going to be a challenge for us so if you see it in stock don’t take too long making up your mind or you may be in for a bit of a wait.
My Vimeo Table Top Review for the Diana Bandit PCP .177 Caliber Bolt Action Pellet Pistol:
